Induction Motors. Standard AC Motors. Constant Speed Motors. Standard AC Motors C-19. Induction Motors

Transcription

1 Standard AC Introduction Induction Induction Standard AC Constant Speed Induction Reversible Electromagnetic Brake Clutch & Synchronous Brake Low-Speed Synchronous Watertight, Dust-Resistant Gearheads Linear Heads Brake Pack Accessories Installation Page Features and Types of Induction C-2 General Specifi cations C-2 World K Series [1 W 9 W (1/7 HP 1/ HP)] C-2 BH Series [2 W ] C- 2-Pole, High-Speed Type [4 W 1 W (1/19 HP 1/ HP)] C-7 C-19

2 Induction (1/7 HP, 1/2 HP) Features and Types of Induction 1 W (1/ HP) 2 W (1/3 HP) Features of Induction Optimal for Uni-Directional and Continuous Operation Induction motors are optimal for uni-directional and continuous operation such as a conveyor system. Easy Operation All you need is to connect a capacitor and plug the motor into an AC power supply and the motor can be easily operated. (No capacitor is needed for a three-phase motor.) Extensive Lineup The World K Series and BH Series are available. We have models with an output power range of 1 W (1/7 HP) to 2 W, so you can find a motor that meets your specific application. Compatible with Various Gearheads Combination with a gearhead allows the motor speed to be reduced to the required speed or generate higher torque. 4 W Types of Induction Series Features, Lineup 9 W 2 W World K Series Conforms to Safety Standards All World K Series models have an overheat protection device built-in and conform to major safety standards. Applicable Standards UL/CSA Standards Certified under the China Compulsory Certification System (CCC System) CE Marking (Low Voltage Directive) Except Conduit Box Type Overheat Protection Device Thermal protector, Impedance protected The Bearing Life is Twice as Long as a Conventional Type A motor's life is determined by its bearing. We adopted high-performance bearing grease to lubricate this important component. As a result, the bearings of World K Series motors last twice as long as conventional bearings. [Excluding 1 W (1/7 HP) and 3 W (1/2 HP) type.] Protective Earth Terminal on the 2-Pole 4-1 W (1/19-1/ HP) Global Voltage Specifications The World K Series supports the power supply voltages used in major countries. meeting the local voltage standard are readily available in major countries in Europe, Asia and North America. Protective Earth Terminal Lineup Frame Size 42 mm ( 1.6 in.) 9 mm ( 3.4 in.) Lead Wire Type: 1 W 9 W (1/7 HP 1/ HP) Terminal Box Type: 2 W 9 W (1/3 HP 1/ HP) Output Power Conduit Box Type: 2 W 9 W (1/3 HP 1/ HP) 2-Pole, High-Speed Type: 4 W 1 W (1/19 HP 1/ HP) Single-Phase 11/11 VAC Voltage Single-Phase 22/23 VAC Three-Phase 2/22/23 VAC BH Series Smallest Frame Size among 2 W These motors achieve a high output of 2 W with a frame size of 14 mm (4.9 in.). Tapped Hole at the Shaft End The gearhead shaft features a tapped hole for convenient connection with loads. Lineup Frame Size Output Power Hypoid Gear Right Angle Type is Available. 14 mm ( 4.9 in.) 2 W "Combination Type" for Easy Installation With each combination type, the motor and gearhead come pre-assembled for easy installation into your equipment. Conforms to Safety Standards and Global Voltage Specifications Type Cable Type:, Hollow Shaft Type,, Solid Shaft Type, Parallel Shaft Type, Round Shaft Type Terminal Box Type:, Hollow Shaft Type,, Solid Shaft Type, Parallel Shaft Type, Round Shaft Type Voltage Single-Phase 11/11 VAC Single-Phase 22/23 VAC Three-Phase 2/22/23 VAC C-2 ORIENTAL MOTOR GENERAL CATALOG 212/213

3 Standard AC Features of Gearheads Easy Speed Reduction and Increase Combination with a gearhead allows the motor speed to be reduced to the required speed or generate higher torque. Wide Variety of Products Gearheads come in various types including the long life, low noise gearhead and right-angle gearhead. Most gearheads are available with 2 different gear ratios from 3:1 to 1:1. Gearhead Pinion Shaft Combine gearheads with a pinion shaft type motor. Gearheads of World K Series are sold separately. BH Series comes with the gearhead pre-assembled. Introduction Induction Reversible Types of Gearheads Types Features Electromagnetic Brake Long Life, Low Noise GN-S Gearhead Long Life GE-S Gearhead Long Rated Life of 1 Hours The GN-S gearhead achieves a long rated life of 1 hours, twice the level of a conventional gearhead, by adopting a large, specially designed bearing and reinforced gears. Low Noise Design The GN-S gearhead generates less noise thanks to gears with a special shape and surface machining assembled with the use of advanced technology. Applicable Products, 1 W (1/ HP), 2 W (1/3 HP) or 4 W GN pinion motor Long Rated Life of 1 Hours The GE-S gearhead achieves a long rated life of 1 hours, twice the level of a conventional gearhead, by adopting a large, specially designed bearing and reinforced gears. The GE-S gearhead comes with a tapped hole at the tip of the shaft. Sound Pressure Level [db(a)] : Long Life, Low Noise GN-S Gearhead 4IK2GN-AW2J/4GN12S : GN-K Gearhead (Conventional ) 4IK2GN-A/4GN12K [Measurement conditions] Load: 1.2 N m Direction: Clockwise Measurement distance: 1 m (Measured in A-weighted sound pressure level) K 1.6K 2.K 4K 6.3K 1K 16K K 2K 3.1K K K 12.K 2K Frequency [Hz] Applicable Products or 9 W GE pinion motor Clutch & Synchronous Brake Low-Speed Synchronous Watertight, Dust-Resistant Gearheads Gearhead Page C-227 Ideal Space-Saving Solution The gear shaft is positioned at right angles with the motor shaft, enabling space-saving. Hollow Shaft and Solid Shaft Types are Available Select an appropriate type that suits your specific application. Solid shaft type of GE pinion gearhead comes with a tapped hole at the tip of the shaft. Applicable Products 2 W (1/3 HP), 4 W, or 9 W pinion motor Linear Heads Brake Pack Accessories Installation High Strength, Long Life, Low Noise Highest Maximum Permissible torque, 1, hours of life and quiet operation. For more details on see page C-149 or visit CAD Data Manuals Technical Support TEL: () techsupport@orientalmotor.com C-21

4 Induction (1/7 HP, 1/2 HP) 1 W (1/ HP) 2 W (1/3 HP) 4 W 9 W Product Line of Induction World K Series Series Voltage (VAC) Type 2-Pole, High-Speed Type BH Series Single-Phase 11/11 Single-Phase 22/23 Three-Phase 2/22/23 Single-Phase 11/11 Single-Phase 22/23 Three-Phase 2/22/23 Single-Phase 11/11 Single-Phase 22/23 Three-Phase 2/22/23 42 mm ( 1.6 in.) (1/7 HP, 1/2 HP) 6 mm 7 mm ( 2.36 in.) ( 2.76 in.) 1 W (1/ HP) 2 W (1/3 HP) Frame Size, Output Power mm ( 3.1 in.) 4 W 4 W 9 mm ( 3.4 in.) 9 W Lead Wire Terminal Box Conduit Box Lead Wire Terminal Box Conduit Box Lead Wire Terminal Box Conduit Box Lead Wire Lead Wire Lead Wire Terminal Box Cable Terminal Box Cable Terminal Box Cable Terminal Box 1 W (1/ HP) 14 mm ( 4.9 in.) 2 W 2 W Product Line of Gearheads Gearhead Applicable Rated Life Type of Gearhead Type of Pinion Series Output Power Type of Pinion (hours) Low Noise 2-Pole 4-1 W (1/19-1/ HP) Long Life, Low Noise GN-S Gearhead GN Type Pinion Shaft World K Series 4 W (1/12 HP 1/19 HP) GN Type Pinion Shaft 1 Parallel Shaft GN-K Gearhead GN Type Pinion Shaft World K Series 1 W 4 W (1/7 HP 1/19 HP) GN Type Pinion Shaft Long Life GE-S Gearhead GE Type Pinion Shaft World K Series, 9 W (1/12 HP, 1/ HP) GE Type Pinion Shaft 1 Shaft Hollow Shaft Gearhead Solid Shaft Gearhead GN Type Pinion Shaft GE Type Pinion Shaft GN Type Pinion Shaft GE Type Pinion Shaft World K Series World K Series World K Series World K Series 2 W, 4 W (1/3 HP, 1/19 HP), 9 W (1/12 HP, 1/ HP) 2 W, 4 W (1/3 HP, 1/19 HP), 9 W (1/12 HP, 1/ HP) GN Type Pinion Shaft GE Type Pinion Shaft GN Type Pinion Shaft GE Type Pinion Shaft C-22 ORIENTAL MOTOR GENERAL CATALOG 212/213

5 Standard AC System Configuration Gearheads (Sold separately) Introduction Parallel Shaft Gearheads ( Page C-21) Gearheads ( Page C-227) Hollow Shaft Type Solid Shaft Type Induction Reversible Induction (Pinion Shaft) Peripheral Equipment (Sold separately) Electromagnetic Brake (Included) Cap (Included) AC Power Supply (Main power supply) Brake Pack SBW ( Page C-23) Speed Controller FE1/FE2 ( Page D-17) Clutch & Synchronous Brake Low-Speed Synchronous Accessories (Sold separately) Watertight, Dust-Resistant Mounting Brackets ( Page C-264) Flexible Couplings ( Page C-269) Gearheads Example of System Configuration Sold Separately Sold Separately Induction Long Life, (Pinion shaft) Mounting Bracket Flexible Coupling Low Noise Gearhead 4IK2GN-AW2U 4GN2SA SOL4U1 MCL3F6F6 Gearheads cannot be combined with round shaft type motors. The system confi guration shown above is an example. Other combinations are available. Linear Heads Brake Pack Accessories Installation CAD Data Manuals Technical Support TEL: () techsupport@orientalmotor.com C-23

6 Induction (1/7 HP, 1/2 HP) 1 W (1/ HP) 2 W (1/3 HP) 4 W 9 W 2 W 2-Pole 4-1 W (1/19-1/ HP) Product Number Code World K Series I K 4 GN - AW 2 T U Frame Size : 42 mm (1.6 in.) 2: 6 mm (2.36 in.) 3: 7 mm (2.76 in.) 4: mm (3.1 in.) : 9 mm (3.4 in.) 2 Type I: Induction 3 Series K: K Series 4 Output Power (W) (Example) 4: 4 W Shaft Type, A: Round Shaft GN: GN Type Pinion Shaft GE: GE Type Pinion Shaft Type of Pinion 6 Power Supply Voltage/ Number of Poles 2, 3: RoHS-Compliant T: Terminal Box Type AW: Single-Phase 11/11 VAC 4-Pole BW: Single-Phase 11/11 VAC 2-Pole CW: Single-Phase 22/23 VAC 4-Pole DW: Single-Phase 22/23 VAC 2-Pole SW: Three-Phase 2/22/23 VAC 4-Pole TW: Three-Phase 2/22/23 VAC 2-Pole 7 9 Included U: For Single-Phase 11/11 VAC E: For Single-Phase 22/23 VAC Blank: Three-Phase Type The U and E at the end of the model name indicate that the unit includes a capacitor. These letters are not listed on the motor nameplate. When the motor is approved under various safety standards, the model name on the nameplate is the approved model name. (Example) : IK4GN-AW2U nameplate and product approved under various safety standards: IK4GN-AW2 Conduit Box Type I K 4 GN - F C H Frame Size 4: mm (3.1 in.) : 9 mm (3.4 in.) 2 Type I: Induction 3 Series K: K Series 4 Output Power (W) (Example) 4: 4 W Shaft Type, A, AA: Round Shaft GN: GN Type Pinion Shaft GE: GE Type Pinion Shaft Type of Pinion 6 Power Supply Voltage F: Single-Phase 11/11 VAC E: Single-Phase 22/23 VAC S: Three-Phase 2/22/23 VAC 7 C: With H: Conduit Box Type Gearhead GN SA Gearhead Frame Size : 42 mm (1.6 in.) 2: 6 mm (2.36 in.) 3: 7 mm (2.76 in.) 4: mm (3.1 in.) : 9 mm (3.4 in.) 2 Type of Pinion GN: GN Type Pinion GE: GE Type Pinion 3 Gear Ratio (Example) : Gear Ratio of :1 1X denotes the decimal gearhead of gear ratio 1:1 GN Type Pinion SA: Long Life, Low Noise GN-S Gearhead KA: GN-K Gearhead RH:, Hollow Shaft Gearhead RAA:, Solid Shaft Gearhead 4 GE Type Pinion SA: Long Life GE-S Gearhead RH:, Hollow Shaft Gearhead RAA:, Solid Shaft Gearhead BH Series BH I 6 2 F T - 1 RH Series BH: BH Series 2 Type I: Induction 3 Frame Size 6: 14 mm (4.9 in.) 4 Output Power (W) (Example) 2: 2 W Power Supply Voltage F: Single-Phase 11/11 VAC E: Single-Phase 22/23 VAC S: Three-Phase 2/22/23 VAC 6 T: Terminal Box Type Blank: Cable Type 7 Gear Ratio, Shaft Type A: Round Shaft Type Number: Gear Ratio of Combination Type Type of Gearhead RH:, Hollow Shaft Type RA:, Solid Shaft Type Blank: Parallel Shaft Type (Combination type only) C-24 ORIENTAL MOTOR GENERAL CATALOG 212/213

7 Standard AC General Specifications World K Series 1 W (1/7 HP), 3 W (1/2 HP) Type Item Specifications Insulation Resistance 1 MΩ or more when VDC megger is applied between the windings and the case after rated operation under normal ambient temperature and humidity. Dielectric Strength Sufficient to withstand 1. kvac at Hz or 6 Hz applied between the windings and the case for 1 minute after rated operation under normal ambient temperature and humidity. Temperature Rise Temperature rise of windings are 7 C (13 F) or less measured by the resistance change method after rated operation under normal ambient temperature and humidity with connecting a gearhead or equivalent heat radiation plate. Thermal Class UL/CSA standards: 1 (A), EN standards: 12 (E) Overheat Protection Impedance protected Ambient Temperature 1 +4 C ( F) (non-freezing) Ambient Humidity % or less (non-condensing) Degree of Protection IP2 9 W Type, 2-Pole/High-Speed Type Item Specifications Insulation Resistance 1 MΩ or more when VDC megger is applied between the windings and the case after rated operation under normal ambient temperature and humidity. Dielectric Strength Sufficient to withstand 1. kvac at Hz or 6 Hz applied between the windings and the case for 1 minute after rated operation under normal ambient temperature and humidity. Temperature Rise Temperature rise of windings are C (1 F) or less measured by the resistance change method after rated operation under normal ambient temperature and humidity with connecting a gearhead or equivalent heat radiation plate. [Three-phase type: 7 C (126 F) or less] Thermal Class 13 (B) type has impedance protection. Overheat Protection Other Types Built-In thermal protector (automatic return type) Open: 13± C (266±9 F), Close: 2±1 C (179.6±27 F) Three-Phase 1 W Type Open: 13± C (266±9 F), Close: 9±1 C (194±27 F) Ambient Temperature Single-phase 11/11 VAC, Single-phase 22/23 VAC, Three-phase 22/23 VAC: 1 +4 C ( F) (non-freezing) Three-phase 2 VAC: 1 + C ( F) (non-freezing) Ambient Humidity % or less (non-condensing) Degree of Protection Lead Wire Type: IP2 Terminal Box Type, Conduit Box Type: IP4 (excluding the installation surface of the round shaft type) Heat radiation plate (Material: Aluminum) Type Size: mm (in.) Thickness: mm (in.) 1 W (1/7 HP), 3 W (1/2 HP) Type ( ) Type ( ) 1 W (1/ HP) Type ( ) 2 W (1/3 HP) Type (2-Pole, High-Speed 4IK4 Type, 4IK6 Type) (.31.31) (.2) 4 W Type (2-Pole, High-Speed IK6 Type) (6. 6.), 9 W, 1 W (1/ HP) Type 2 2 ( ) Introduction Induction Reversible Electromagnetic Brake Clutch & Synchronous Brake Low-Speed Synchronous Watertight, Dust-Resistant BH Series Item Insulation Resistance Dielectric Strength Temperature Rise Thermal Class Overheat Protection Ambient Temperature Ambient Humidity Degree of Protection Specifications 1 MΩ or more when VDC megger is applied between the windings and the case after rated operation under normal ambient temperature and humidity. Sufficient to withstand 1. kvac at Hz or 6 Hz applied between the windings and the case for 1 minute after rated operation under normal ambient temperature and humidity. Temperature rise of windings are 7 C (126 F) or less measured by the resistance change method after rated operation under normal ambient temperature and humidity with connecting a gearhead or equivalent heat radiation plate. 13 (B) Built-in thermal protector (automatic return type) Open: 1± C, (32±9 F), Close: 96±1 C (24.±27 F) Single-phase 11/11 VAC, Single-phase 22/23 VAC, Three-phase 22/23 VAC: 1 +4 C ( F) (non-freezing) Three-phase 2 VAC: 1 + C ( F) (non-freezing) % or less (non-condensing) Cable Type: IP4 Terminal Box Type: IP4 (excluding the installation surface of the round shaft type) Heat radiation plate: mm ( in.), Thickness: mm (.2 in.) (Material: Aluminum) Gearheads Linear Heads Brake Pack Accessories Installation CAD Data Manuals Technical Support TEL: () techsupport@orientalmotor.com C-2

8 Induction (1/7 HP, 1/2 HP) Connection Diagrams The direction of motor rotation is as viewed from the shaft end of the motor. CW represents the clockwise direction, while CCW represents the counterclockwise direction. Single-Phase 11/11 VAC Single-Phase 22/23 VAC Lead Wire Type Three-Phase 2/22/23 VAC Terminal Box Type Single-Phase 11/11 VAC Three-Phase 2/22/23 VAC Single-Phase 22/23 VAC 1 W (1/ HP) 2 W (1/3 HP) 4 W Clockwise L N Counterclockwise L N White Red Black White Red Black CCW CW Clockwise L1(R) L2(S) L3(T) Red White Black CW Counterclockwise To change the rotation direction, change any two connections between L1(R), L2(S) and L3(T). Clockwise L N Counterclockwise L N Z2 U2 U1 Z2 U2 U1 CCW CW Clockwise L1(R) L2(S) L3(T) U V W CW Counterclockwise To change the rotation direction, change any two connections between L1(R), L2(S) and L3(T). 9 W Conduit Box Type Single-Phase IK4GN-AW2T 11/11 VAC Three-Phase 2/22/23 VAC Single-Phase IK4GN-CW2T 22/23 VAC 2 W 2-Pole 4-1 W (1/19-1/ HP) Clockwise NC L N White Red Black Green/Yellow NC: No connection Counterclockwise L NC N White Red Black Green/Yellow CCW CW Clockwise L1(R) L2(S) L3(T) Red White Black Green/Yellow CW Counterclockwise To change the rotation direction, change any two connections between L1(R), L2(S) and L3(T). NC: No connection : Protective Earth Note Change the direction of single-phase motor rotation only after bringing the motor to a stop. If an attempt is made to change the direction of rotation while the motor is rotating, motor may ignore reversing command or change its direction of rotation after some delay. How to connect a capacitor Page C-22 C-26 ORIENTAL MOTOR GENERAL CATALOG 212/213

9 Standard AC Introduction Induction Reversible Electromagnetic Brake Clutch & Synchronous Brake Low-Speed Synchronous Watertight, Dust-Resistant Gearheads Linear Heads Brake Pack Accessories Installation CAD Data Manuals Technical Support TEL: () C-27

10 Induction (1/7 HP, 1/2 HP) Induction 1 W (1/7 HP), 3 W (1/2 HP) Frame Size: 42 mm ( 1.6 in.) (Gearhead sold separately) 1 W (1/ HP) 2 W (1/3 HP) 4 W 9 W 2 W 2-Pole 4-1 W (1/19-1/ HP) Specifications Continuous Rating Pinion Shaft Type IK1GN-AW3U IK3GN-BW3U Lead Wire Type Round Shaft Type IK1A-AW3U IK3A-BW3U Output Power W HP VAC Hz A 1 Single-Phase /7 Single-Phase Single-Phase /2 Single-Phase Voltage Frequency Current Starting Rated mn m oz-in The U at the end of the model name indicates that the unit includes a capacitor. This letter is not listed on the motor nameplate. When the motor is approved under various safety standards, the model name on the nameplate is the approved model name. Page H-11 Details of safety standards Page H-2 : Impedance protected. Product Line Type Lead Wire Pinion Shaft Type IK1GN-AW3U IK3GN-BW3U The following items are included in each product.,, Cap, Operating Manual Round Shaft Type IK1A-AW3U IK3A-BW3U Gearmotor Table Rated Speed mn m oz-in r/min μf Parallel Shaft Gearhead (Sold separately) Gearhead Type Gearhead Gear Ratio Parallel Shaft GN-K Gearhead GN KA The following items are included in each product. Gearhead, Mounting Screws, Operating Manual 3, 3.6,, 6, 7., 9, 12., 1, 1, 2, 3, 36,, 6, 7, 9, 1, 12, 1, 1 Enter the gear ratio in the box ( ) within the gearhead model name. A colored background ( ) indicates gear shaft rotation in the same direction as the motor shaft, while the others rotate in the opposite direction. The speed is calculated by dividing the motor's synchronous speed (4-pole type; 6 Hz: 1 r/min, 2-pole type; 6 Hz: 36 r/min) by the gear ratio. The actual speed is 2 33% less than the displayed value, depending on the load. 6 Hz / Gearhead Speed r/min Unit = Upper values: N m/lower values: lb-in Gear Ratio IK1GN-AW3U GN KA / Gearhead Speed r/min IK3GN-BW3U GN KA Unit = Upper values: N m/lower values: lb-in Gear Ratio Permissible Overhung Load and Permissible Thrust Load (Round shaft type) Page C-17 Gearhead Page C-17 Permissible Load Inertia J of Gearhead Page C-1 C-2 ORIENTAL MOTOR GENERAL CATALOG 212/213 Page Features C-2 / System Configuration C-23 / Specifications C-2 / Product Line C-2 Dimensions C-29 / Connection Diagrams C-26

11 Standard AC Dimensions Unit = mm (in.) Mounting screws are included with gearheads. Dimensions for mounting screws Page C-2 Lead Wire Type Gearhead DXF IK1GN-AW3U IK3GN-BW3U GN KA A1U Mass:.3 kg (.66 lb.) Gearhead.2 kg (. lb.) 2 (1.1) 2 (.) 7. (.3) 16. (.6) 1 (.39) 7.2 (.29) 6 (2.36) 26 (1.2) (.2) 3 (.12) 2 (.79) 12.7 (.) (.172) Leads 3 mm (12 in.) Length UL Style 3266, AWG22 Detail Drawing of Protective Earth Terminal (Included) A ϕ4.3 (ϕ.169) 2 (.79) B 4. (.1) Protective Earth Terminal M4 B+1 (.39) ϕ ϕ.17. (3/16") (.32) ϕ1 (ϕ.71) 42 (1.6) 4 ϕ3. (ϕ.13) Thru 42 (1.6) 1 (.39) 4±. (1.9±.2) 7 (.2) max. Protective Earth Terminal M4 Dimensions Unit = mm (in.) Pinion Shaft Type Round Shaft Type Shaft Section of Round Shaft Type The motor s dimensions (excluding the shaft section) are the same as those of the pinion shaft types. Mass DXF IK1A-AW3U IK3A-BW3U 2 (.79) 1. (.6).3 kg (.66 lb.) 42 (1.6) 4 ϕ3. (ϕ.13) Thru 1 (.39) IK1GN-AW3U IK1A-AW3U CH1FAUL IK3GN-BW3U IK3A-BW3U CH1FAUL ϕ.12 (ϕ.1969.) ϕ (ϕ1.43.1) A B C 31 (1.22) 31 (1.22) 14. (.7) 14. (.7) 42 (1.6) 23. (.93) 23. (.93) A2 4±. (1.9±.2) 7 (.2) max. Protective Earth Terminal M4 Mass g (oz.) 1 (.64) 1 (.64) Cap Included Introduction Induction Reversible Electromagnetic Brake Clutch & Synchronous Brake Low-Speed Synchronous Watertight, Dust-Resistant AMP#17 4 (.16) 1 C (.39) 6 (.24) Connection Diagrams Page C-26 Accessories and Peripheral Equipment Instantaneous Stop Brake Pack Page C-23 Accessories Page C-263 Gearheads Linear Heads Brake Pack Accessories Installation CAD Data Manuals Technical Support TEL: () techsupport@orientalmotor.com C-29

12 Induction (1/7 HP, 1/2 HP) Induction Frame Size: 6 mm ( 2.36 in.) (Gearhead sold separately) 1 W (1/ HP) 2 W (1/3 HP) 4 W 9 W 2 W 2-Pole 4-1 W (1/19-1/ HP) Specifications Continuous Rating Pinion Shaft Type 2IK6GN-AW2U 2IK6GN-CW2E 2IK6GN-SW2 Lead Wire Type Round Shaft Type 2IK6A-AW2U 2IK6A-CW2E 2IK6A-SW2 Output Power W HP VAC Hz A 6 Single-Phase /12 Single-Phase /12 6 1/12 Voltage Frequency Current Starting Rated Single-Phase 22 Single-Phase 23 Three-Phase Three-Phase Three-Phase mn m oz-in The U and E at the end of the model name indicate that the unit includes a capacitor. These letters are not listed on the motor nameplate. When the motor is approved under various safety standards, the model name on the nameplate is the approved model name. Page H-11 Details of safety standards Page H-2 : Impedance protected Rated Speed mn m oz-in r/min μf Product Line Type Lead Wire Pinion Shaft Type 2IK6GN-AW2U 2IK6GN-CW2E 2IK6GN-SW2 The following items are included in each product.,, Cap, Operating Manual Only for single-phase motors Round Shaft Type 2IK6A-AW2U 2IK6A-CW2E 2IK6A-SW2 Parallel Shaft Gearhead (Sold separately) Gearhead Type Gearhead Gear Ratio Parallel Shaft Long Life, Low Noise GN-S Gearhead The following items are included in each product. Gearhead, Mounting Screws, Operating Manual 3, 3.6,, 6, 7., 9, 12., 2GN SA 1, 1, 2, 3, 36,, 6, 7, 9, 1, 12, 1, 1 2GN1XS (Decimal Gearhead) The following gearheads are also available. For details, please refer to website ( or contact the nearest Oriental sales office. Gearhead Type Gearhead Gear Ratio Parallel 2GN KA 3 1 Shaft GN-K Gearhead 2GN1XK (Decimal Gearhead) High Strength, Long Life, Low Noise Highest Maximum Permissible torque, 1, hours of life and quiet operation. For more details on see page C-149 or visit C-3 ORIENTAL MOTOR GENERAL CATALOG 212/213 Page Features C-2 / System Configuration C-23 / Specifications C-3 / Product Line C-3 Dimensions C-31 / Connection Diagrams C-26

13 Standard AC Gearmotor Table Enter the gear ratio in the box ( ) within the gearhead model name. A colored background ( ) indicates gear shaft rotation in the same direction as the motor shaft, while the others rotate in the opposite direction. The speed is calculated by dividing the motor's synchronous speed ( Hz: 1 r/min, 6 Hz: 1 r/min) by the gear ratio. The actual speed is 2 2% less than the displayed value, depending on the load. To reduce the speed beyond the gear ratio in the table, attach a decimal gearhead (gear ratio 1:1) between the gearhead and the motor. In that case, the permissible torque is 3 N m (26 lb-in). Hz / Gearhead 2IK6GN-CW2E 2IK6GN-SW2 6 Hz / Gearhead 2IK6GN-AW2U 2IK6GN-CW2E 2IK6GN-SW2 Speed r/min Unit = Upper values: N m/lower values: lb-in Gear Ratio GN SA Speed r/min Unit = Upper values: N m/lower values: lb-in Gear Ratio GN SA Permissible Overhung Load and Permissible Thrust Load (Round shaft type) Page C-17 Gearhead Page C Permissible Load Inertia J of Gearhead Page C-1 Dimensions Unit = mm (in.) Mounting screws are included with gearheads. Dimensions for mounting screws Page C Introduction Induction Reversible Electromagnetic Brake Clutch & Synchronous Brake Low-Speed Synchronous Watertight, Dust-Resistant Lead Wire Type Mass:.7 kg (1.4 lb.) Gearhead.4 kg (. lb.) ϕ6 (ϕ2.36) 7 (2.9) 7 (.2) L (.2) 32 (1.26) 12.7 (.) (.293) 1 (.39) ϕ24 (ϕ.94) Leads 3 mm (12 in.) Length UL Style 3271, AWG2 ϕ ϕ (/16") 6 (2.36) 4 ϕ4. (ϕ.) Thru 6 (2.36) 22. 7±. (2.76±.2) Protective Earth Terminal M4 (.2) max. Gearhead Gear Ratio L DXF 2IK6GN-AW2U 2IK6GN-CW2E 2IK6GN-SW2 2GN SA (.) Protective Earth Terminal M4 1. (.61) 3 (1.1) 4 (1.7) Detail Drawing of Protective Earth Terminal A3AU A3BU Gearheads Linear Heads Brake Pack Accessories Installation CAD Data Manuals Technical Support TEL: () techsupport@orientalmotor.com C-31

14 Induction (1/7 HP, 1/2 HP) 1 W (1/ HP) 2 W (1/3 HP) 4 W Shaft Section of Round Shaft Type The motor s dimensions (excluding the shaft section) are the same as those of the pinion shaft types. Mass DXF 2IK6A-AW2U 2IK6A-CW2E 2IK6A-SW2 2 (.) 24 (.94) ϕ6.12 (ϕ.2362.) ϕ4.3 (ϕ ) 6 ( 2.36) 4 ϕ4. (ϕ.) Thru.7 kg (1.4 lb.) A ±. (2.76±.2) Protective Earth Terminal M4 (.2) max. Decimal Gearhead Can be connected to GN pinion shaft type. 2GN1XS Mass:.2 kg (. lb.) A3 3. (1.1) (1.2) (.49) 2 (.) ϕ4.3 (ϕ ) 6 ( 2.36) 4 ϕ4. (ϕ.) Thru 7±. (2.76±.2) 9 W 2 W (Included with single-phase motors) A ϕ4.3 (ϕ.169) 2 (.79) B 4. (.1) B+1 (.39) Dimensions Unit = mm (in.) Pinion Shaft Type Round Shaft Type 2IK6GN-AW2U 2IK6A-AW2U CH2FAUL2 2IK6GN-CW2E 2IK6A-CW2E CH6BFAUL A B C 31 (1.22) 31 (1.22) 17 (.67) 14. (.7) 27 (1.6) 23. (.93) Mass g (oz.) 21 (.74) 1 (.64) Cap Included 2-Pole 4-1 W (1/19-1/ HP) AMP#17 4 (.16) 1 C (.39) 6 (.24) Connection Diagrams Page C-26 Accessories and Peripheral Equipment Instantaneous Stop Brake Pack Page C-23 Speed Control Speed Controller Page D-17 Accessories Page C-263 C-32 ORIENTAL MOTOR GENERAL CATALOG 212/213 Page Features C-2 / System Configuration C-23 / Specifications C-3 / Product Line C-3 Dimensions C-31 / Connection Diagrams C-26

15 Standard AC Induction 1 W (1/ HP) Frame Size: 7 mm ( 2.76 in.) (Gearhead sold separately) Introduction Induction Specifications Continuous Rating Pinion Shaft Type Lead Wire Type 3IK1GN-AW2U 3IK1GN-CW2E 3IK1GN-SW2 Round Shaft Type 3IK1A-AW2U 3IK1A-CW2E 3IK1A-SW2 Output Power W HP VAC Hz A 1 Single-Phase / Single-Phase / 1 1/ Voltage Frequency Current Starting Rated Single-Phase 22 Single-Phase 23 Three-Phase Three-Phase Three-Phase mn m oz-in Rated Speed mn m oz-in r/min μf The U and E at the end of the model name indicate that the unit includes a capacitor. These letters are not listed on the motor nameplate. When the motor is approved under various safety standards, the model name on the nameplate is the approved model name. Page H-11 Details of safety standards Page H-2 : Contains a built-in thermal protector (automatic return type). If a motor overheats for any reason, the thermal protector is activated and the motor is stopped. When the motor temperature drops, the thermal protector closes and the motor restarts. Be sure to turn the motor power off before inspecting. Reversible Electromagnetic Brake Clutch & Synchronous Brake Low-Speed Synchronous Watertight, Dust-Resistant Product Line Type Pinion Shaft Type Round Shaft Type 3IK1GN-AW2U 3IK1A-AW2U Lead Wire 3IK1GN-CW2E 3IK1A-CW2E 3IK1GN-SW2 3IK1A-SW2 The following items are included in each product.,, Cap, Operating Manual Only for single-phase motors Parallel Shaft Gearhead (Sold separately) Gearhead Type Gearhead Gear Ratio Parallel Shaft Long Life, Low Noise GN-S Gearhead The following items are included in each product. Gearhead, Mounting Screws, Operating Manual 3, 3.6,, 6, 7., 9, 12., 3GN SA 1, 1, 2, 3, 36,, 6, 7, 9, 1, 12, 1, 1 3GN1XS (Decimal Gearhead) The following gearheads are also available. For details, please refer to website ( or contact the nearest Oriental sales office. Gearhead Type Gearhead Gear Ratio Parallel 3GN KA 3 1 Shaft GN-K Gearhead 3GN1XK (Decimal Gearhead) Gearheads Linear Heads Brake Pack Accessories Installation High Strength, Long Life, Low Noise Highest Maximum Permissible torque, 1, hours of life and quiet operation. For more details on see page C-149 or visit CAD Data Manuals Technical Support TEL: () techsupport@orientalmotor.com C-33

16 Induction (1/7 HP, 1/2 HP) 1 W (1/ HP) 2 W (1/3 HP) 4 W 9 W 2 W 2-Pole 4-1 W (1/19-1/ HP) Gearmotor Table Enter the gear ratio in the box ( ) within the gearhead model name. A colored background ( ) indicates gear shaft rotation in the same direction as the motor shaft, while the others rotate in the opposite direction. The speed is calculated by dividing the motor's synchronous speed ( Hz: 1 r/min, 6 Hz: 1 r/min) by the gear ratio. The actual speed is 2 2% less than the displayed value, depending on the load. To reduce the speed beyond the gear ratio in the table, attach a decimal gearhead (gear ratio 1:1) between the gearhead and the motor. In that case, the permissible torque is N m ( lb-in). Hz / Gearhead Speed r/min 3IK1GN-CW2E 3GN SA IK1GN-SW2 3GN SA Hz / Gearhead 3IK1GN-AW2U 3IK1GN-CW2E Unit = Upper values: N m/lower values: lb-in Gear Ratio Speed r/min Unit = Upper values: N m/lower values: lb-in Gear Ratio GN SA IK1GN-SW2 3GN SA Permissible Overhung Load and Permissible Thrust Load (Round shaft type) Page C-17 Gearhead Page C-17 Permissible Load Inertia J of Gearhead Page C Dimensions Unit = mm (in.) Mounting screws are included with gearheads. Dimensions for mounting screws Page C-2 Lead Wire Type Mass: 1.1 kg (2.4 lb.) Gearhead. kg (1.21 lb.) ϕ69 (ϕ2.72) (3.1) 7 L 32 (1.26) (.2) 12.7 (.2) (.).2 (.347) ϕ9.2.1 ϕ.37.6 (3/") 1 (.9) ϕ3 (ϕ1.1) Leads 3 mm (12 in.) Length UL Style 3271, AWG2 7 (2.76) 4 ϕ. (ϕ.217) Thru 7 (2.76) 22. 2±. (3.23±.2) Protective Earth Terminal M4 (.2) max. Gearhead Gear Ratio L DXF 3IK1GN-AW2U 3IK1GN-CW2E 3IK1GN-SW2 3GN SA (.) Protective Earth Terminal M4 16. (.6) 32 (1.26) 42 (1.6) Detail Drawing of Protective Earth Terminal A7AU A7BU C-34 ORIENTAL MOTOR GENERAL CATALOG 212/213 Page Features C-2 / System Configuration C-23 / Specifications C-33 / Product Line C-33 Dimensions C-34 / Connection Diagrams C-26

17 Standard AC Shaft Section of Round Shaft Type The motor s dimensions (excluding the shaft section) are the same as those of the pinion shaft types. Mass DXF 3IK1A-AW2U 3IK1A-CW2E 3IK1A-SW2 2 (.) 32 (1.26) ϕ6.12 (ϕ.2362.) ϕ64.3 (ϕ ) 7 ( 2.76) 4 ϕ. (ϕ.217) Thru 1.1 kg (2.4 lb.) A 22. (Included with single-phase motors) A ϕ4.3 (ϕ.169) AMP#17 2 (.79) B 4. (.1) 4 (.16) 1 C (.39) B+1 (.39) 6 (.24) Connection Diagrams Page C-26 Accessories and Peripheral Equipment Instantaneous Stop Brake Pack Page C-23 Speed Control Speed Controller Page D-17 2±. (3.23±.2) Protective Earth Terminal M4 (.2) max. Accessories Page C-263 Decimal Gearhead Can be connected to GN pinion shaft type. 3GN1XS Mass:.3 kg (.66 lb.) A9 43 (1.69) 3 13 (1.1) (.1) 2 (.) ϕ64.3 (ϕ ) 7 ( 2.76) 4 ϕ. (ϕ.217) Thru Dimensions Unit = mm (in.) Pinion Shaft Type Round Shaft Type 3IK1GN-AW2U 3IK1A-AW2U CH4FAUL2 3IK1GN-CW2E 3IK1A-CW2E CH1BFAUL 2±. (3.23±.2) A B C 37 (1.46) 37 (1.46) 1 (.71) 1 (.71) 27 (1.6) 27 (1.6) Mass g (oz.) 26 (.92) 27 (.9) Cap Included Introduction Induction Reversible Electromagnetic Brake Clutch & Synchronous Brake Low-Speed Synchronous Watertight, Dust-Resistant Gearheads Linear Heads Brake Pack Accessories Installation CAD Data Manuals Technical Support TEL: () techsupport@orientalmotor.com C-3

18 Induction (1/7 HP, 1/2 HP) Induction 2 W (1/3 HP) Frame Size: mm ( 3.1 in.) Lead Wire Type Terminal Box Type (Gearhead sold separately) 1 W (1/ HP) 2 W (1/3 HP) Specifications Continuous Rating Lead Wire Type Dimension 1 Upper Name: Pinion Shaft Type Lower Name ( ): Round Shaft Type Terminal Box Type Dimension 2 Conduit Box Type Dimension 3 Output Power Voltage Frequency Current W HP VAC Hz A Starting mn m oz-in Rated Rated Speed mn m oz-in r/min μf 4 W 4IK2GN-AW2U (4IK2A-AW2U) 4IK2GN-CW2E (4IK2A-CW2E) 4IK2GN-AW2TU (4IK2A-AW2TU) 4IK2GN-CW2TE (4IK2A-CW2TE) 4IK2GN-FCH (4IK2AA-FCH) 2 1/3 2 1/3 Single-Phase 11 Single-Phase 11 Single-Phase 22 Single-Phase W 2 W 2-Pole 4-1 W (1/19-1/ HP) 4IK2GN-SW2 (4IK2A-SW2) 4IK2GN-SW2T (4IK2A-SW2T) 4IK2GN-ECH (4IK2AA-ECH) 4IK2GN-SH (4IK2AA-SH) 2 1/3 2 1/3 Single-Phase Single-Phase 23 Three-Phase Three-Phase Three-Phase The U and E at the end of the model name indicate that the unit includes a capacitor. These letters are not listed on the motor nameplate. When the motor is approved under various safety standards, the model name on the nameplate is the approved model name. Page H-11 Details of safety standards Page H-2 Conduit box type is not certified under the China Compulsory Certification System (CCC System). : Contains a built-in thermal protector (automatic return type). If a motor overheats for any reason, the thermal protector is activated and the motor is stopped. When the motor temperature drops, the thermal protector closes and the motor restarts. Be sure to turn the motor power off before inspecting. Product Line Type Lead Wire Terminal Box Conduit Box Pinion Shaft Type Round Shaft Type 4IK2GN-AW2U 4IK2A-AW2U 4IK2GN-CW2E 4IK2A-CW2E 4IK2GN-SW2 4IK2A-SW2 4IK2GN-AW2TU 4IK2A-AW2TU 4IK2GN-CW2TE 4IK2A-CW2TE 4IK2GN-SW2T 4IK2A-SW2T 4IK2GN-FCH 4IK2AA-FCH 4IK2GN-ECH 4IK2AA-ECH 4IK2GN-SH 4IK2AA-SH The following items are included in each product.,, Cap, Operating Manual Only for single-phase motors (Excluding conduit box type) High Strength, Long Life, Low Noise Highest Maximum Permissible torque, 1, hours of life and quiet operation. For more details on see page C-149 or visit C-36 ORIENTAL MOTOR GENERAL CATALOG 212/213 Page Features C-2 / System Configuration C-23 / Specifications C-36 / Product Line C-36 Dimensions C-3 / Connection Diagrams C-26

19 Standard AC Parallel Shaft Gearhead/ Gearhead (Sold separately) Gearhead Type Gearhead Gear Ratio Parallel Shaft Shaft Parallel Shaft Long Life, Low Noise GN-S Gearhead Hollow Shaft Solid Shaft Long Life, Low Noise GN-S Gearhead 4GN SA 3, 3.6,, 6, 7., 9, 12., 1, 1, 2, 3, 36,, 6, 7, 9, 4GN RH 1, 12, 1, 1 4GN RAA 4GN1XS (Decimal Gearhead) The following items are included in each product. Parallel Shaft Gearhead Gearhead, Mounting Screws, Operating Manual Hollow Shaft Gearhead Gearhead, Mounting Screws, Parallel Key, Safety Cover (with screws), Gasket, Operating Manual Solid Shaft Gearhead Gearhead, Mounting Screws, Gasket, Operating Manual The following gearheads are also available. For details, please refer to website ( or contact the nearest Oriental sales office. Gearhead Type Gearhead Gear Ratio Parallel 4GN KA 3 1 Shaft GN-K Gearhead 4GN1XK (Decimal Gearhead) Introduction Induction Reversible Electromagnetic Brake Gearmotor Table Enter the code that represents the terminal box type " T" in the box ( ) within the motor model name. Enter the gear ratio in the box ( ) within the gearhead model name. A colored background ( ) indicates gear shaft rotation in the same direction as the motor shaft, while the others rotate in the opposite direction. The speed is calculated by dividing the motor's synchronous speed ( Hz: 1 r/min, 6 Hz: 1 r/min) by the gear ratio. The actual speed is 2 2% less than the displayed value, depending on the load. To reduce the speed beyond the gear ratio in the table, attach a decimal gearhead (gear ratio 1:1) between the gearhead and the motor. In that case, the permissible torque is N m (7 lb-in). When a gearhead of 2:1 36:1 is connected, the value for permissible torque is 6 N m (3 lb-in). Hz Unit = Upper values: N m/ Lower values: lb-in Speed r/min / Gear Ratio Gearhead 4IK2GN-CW2 E 4IK2GN-ECH 4IK2GN-SW2 4IK2GN-SH 6 Hz / Gearhead 4IK2GN-AW2 U 4IK2GN-CW2 E 4IK2GN-FCH 4IK2GN-ECH 4IK2GN-SW2 4IK2GN-SH 4GN SA GN SA Speed r/min Unit = Upper values: N m/ Lower values: lb-in Gear Ratio GN SA GN SA Gearmotor Table When Gearhead is Attached Page C-23 Permissible Overhung Load and Permissible Thrust Load (Round shaft type) Page C-17 Gearhead Page C Permissible Load Inertia J of Gearhead Page C Clutch & Synchronous Brake Low-Speed Synchronous Watertight, Dust-Resistant Gearheads Linear Heads Brake Pack Accessories Installation CAD Data Manuals Technical Support TEL: () techsupport@orientalmotor.com C-37

20 Induction (1/7 HP, 1/2 HP) 1 W (1/ HP) 2 W (1/3 HP) 4 W 9 W Dimensions Unit = mm (in.) Mounting screws are included with gearheads. Dimensions for mounting screws Page C-2 Lead Wire Type 1 Mass: 1. kg (3.3 lb.) Gearhead.6 kg (1.43 lb.) ϕ79 (ϕ3.11) (3.3) L 32 7 (1.26) (.2) (.24) (.) Terminal Box Type 2 Mass: 1.7 kg (3.7 lb.) Gearhead.6 kg (1.43 lb.).2 (.347) ϕ9.2.1 ϕ.37.6 (3/") 1 (.9) ϕ34 (ϕ1.34) Leads 3 mm (12 in.) Length UL Style 3271, AWG2 (3.1) 4 ϕ. (ϕ.217) Thru (3.1) ±. (3.7±.2) Protective Earth Terminal M4 (.2) max. Gearhead Gear Ratio L DXF 4IK2GN-AW2U 4IK2GN-CW2E 4IK2GN-SW2 4GN SA 21. (.) Protective Earth Terminal M (1.26) (1.67) 16. (.6) Detail Drawing of Protective Earth Terminal A9AU A9BU Gearhead Gear Ratio L DXF 4IK2GN-AW2TU 4IK2GN-CW2TE 4IK2GN-SW2T 4GN SA (1.26) (1.67) A41AU A41BU 2 W 2-Pole 4-1 W (1/19-1/ HP) 2 (1.1) max. ϕ79 (ϕ3.11) 2 (.9) 7 (2.9). (.22) 12.7 (.).2 (.347) ϕ9.2.1 ϕ.37.6 (3/") 1 (.9) ϕ34 (ϕ1.34) 43 (1.69) (3.1) 62 (2.) 94±. (3.7±.2) 7 (.2) (3.3) 6 (.24) L 32 (1.26) Use cable with a diameter of ϕ6 ϕ12 mm (ϕ.24 ϕ.47 in.). Details of terminal box Page C-23 4 ϕ. (ϕ.217) Thru (3.1) Shaft Section of Round Shaft Type The motor s dimensions (excluding the shaft section) are the same as those of the pinion shaft types. 32 (1.26) 2 (.) 2 (.9) 7 (.2) ϕ.1 (ϕ.31.6) ϕ73.3 (ϕ ) ( 3.1) 4 ϕ. (ϕ.217) Thru 94±. (3.7±.2) Protective Earth Terminal M4 (Lead wire type only) (.2) max. Mass DXF 4IK2A-AW2U 4IK2A-CW2E 4IK2A-SW2 4IK2A-AW2TU 4IK2A-CW2TE 4IK2A-SW2T 1. kg (3.3 lb.) 1.7 kg (3.7 lb.) A4 A C-3 ORIENTAL MOTOR GENERAL CATALOG 212/213 Page Features C-2 / System Configuration C-23 / Specifications C-36 / Product Line C-36 Dimensions C-3 / Connection Diagrams C-26

21 Standard AC Conduit Box Type 3 Gearhead Gear Ratio L DXF 4IK2GN-FCH 4GN SA 4IK2GN-ECH Mass: 1.9 kg (4.2 lb.) Gearhead.6 kg (1.43 lb.) ϕ21. 4 (2.13) (ϕ.46) (2.17) 32 (1.26) ϕ79 (ϕ3.11) (1.26) A9AU (1.67) A9BU 7 (2.9) 12.7 (.).2 (.347) ϕ9.2.1 ϕ.37.6 (3/") 1 (.9) ϕ34 (ϕ1.34) (3.1) 94±. (3.7±.2) Introduction Induction Reversible Electromagnetic Brake 3 Leads: UL Style 3266, AWG2 1 Ground Lead: UL Style 3266, AWG1 Details of terminal box Page C-23 7 (.2) (3.3) 6 (.24) L 32 (1.26) Gearhead Gear Ratio L DXF 4IK2GN-SH 4GN SA (1.26) A91AU (1.67) A91BU Mass: 1.7 kg (3.7 lb.) Gearhead.6 kg (1.43 lb.) ϕ21. (ϕ.46) 4 (1.77) 23 (.91) 4 (2.13) 7 (2.9) ϕ79 (ϕ3.11) 12.7 (.).2 (.347) 4 ϕ. (ϕ.217) Thru ϕ9.2.1 ϕ.37.6 (3/") 1 (.9) ϕ34 (ϕ1.34) (3.1) (3.1) 94±. (3.7±.2) Clutch & Synchronous Brake Low-Speed Synchronous Watertight, Dust-Resistant 3 Leads: UL Style 3266, AWG2 1 Ground Lead: UL Style 3266, AWG1 Details of terminal box Page C-23 7 (.2) (3.3) 6 (.24) L 32 (1.26) 4 ϕ. (ϕ.217) Thru (3.1) Gearheads Shaft Section of Round Shaft Type The motor s dimensions (excluding the shaft section) are the same as those of the pinion shaft types. Mass DXF 4IK2AA-FCH 4IK2AA-ECH 1.9 kg (4.2 lb.) ϕ ϕ (/16") 2 (.9) 7.37 (.2) ϕ73.3 ) A9 ϕ ( (3.1) 94±. (3.7±.2) Shaft Section of Round Shaft Type The motor s dimensions (excluding the shaft section) are the same as those of the pinion shaft types. Mass DXF 4IK2AA-SH 1.7 kg (3.7 lb.) A1 ϕ ϕ (/16") 2 (.9) 7.37 (.2) ϕ73.3 ) ϕ (3.1) ( 94±. (3.7±.2) Linear Heads Brake Pack Accessories Installation 2 (.) 32 (1.26) 4 ϕ. (ϕ.217) Thru (3.1) 2 (.) 32 (1.26) 4 ϕ. (ϕ.217) Thru (3.1) CAD Data Manuals Technical Support TEL: () techsupport@orientalmotor.com C-39

22 Induction (1/7 HP, 1/2 HP) 1 W (1/ HP) 2 W (1/3 HP) Decimal Gearhead Can be connected to GN pinion shaft type. 4GN1XS Mass:.4 kg (. lb.) A13 4. (1.79) (1.26) (.3) 2 (.) ϕ73.3 (ϕ ) ( 3.1) 94±. (3.7±.2) 4 W 9 W 2 W 2-Pole 4-1 W (1/19-1/ HP) 4 ϕ. (ϕ.217) Thru (Included with single-phase motors) A ϕ4.3 (ϕ.169) AMP#17 2 (.79) B 4. (.1) 4 (.16) 1 C (.39) B+1 (.39) 6 (.24) Connection Diagrams Dimensions Unit = mm (in.) Upper Name: Pinion Shaft Type Lower Name ( ): Round Shaft Type Lead Wire Type Terminal Box Type 4IK2GN-AW2U (4IK2A-AW2U) 4IK2GN-CW2E (4IK2A-CW2E) 4IK2GN-AW2TU (4IK2A-AW2TU) 4IK2GN-CW2TE (4IK2A-CW2TE) CH6CFAUL2 CH1BFAUL A B C 4 (1.9) 3 (1.) 19 (.7) 21 (.3) 29 (1.14) 31 (1.22) Mass g (oz.) 3 (1.24) 37 (1.31) Cap Included Page C-26 Gearhead, Accessories and Peripheral Equipment Space-Saving Gearheads Page C-227 Instantaneous Stop Brake Pack Page C-23 Speed Control Speed Controller Page D-17 Accessories Page C-263 C-4 ORIENTAL MOTOR GENERAL CATALOG 212/213 Page Features C-2 / System Configuration C-23 / Specifications C-36 / Product Line C-36 Dimensions C-3 / Connection Diagrams C-26

23 Standard AC Induction 4 W Frame Size: 9 mm ( 3.4 in.) Lead Wire Type Terminal Box Type (Gearhead sold separately) Introduction Induction Specifications Continuous Rating Lead Wire Type Dimension 1 IK4GN-AW2U (IK4A-AW2U) IK4GN-CW2E (IK4A-CW2E) IK4GN-SW2 (IK4A-SW2) Upper Name: Pinion Shaft Type Lower Name ( ): Round Shaft Type Terminal Box Type Dimension 2 IK4GN-AW2TU (IK4A-AW2TU) IK4GN-CW2TE (IK4A-CW2TE) IK4GN-SW2T (IK4A-SW2T) Conduit Box Type Dimension 3 IK4GN-FCH (IK4AA-FCH) Output Power IK4GN-ECH 1 4 (IK4AA-ECH) 1 1/19 IK4GN-SH (IK4AA-SH) Voltage Frequency Current W HP VAC Hz A 4 Single-Phase /19 Single-Phase /19 Single-Phase 22 Single-Phase 23 Three-Phase Three-Phase Three-Phase Starting mn m oz-in The U and E at the end of the model name indicate that the unit includes a capacitor. These letters are not listed on the motor nameplate. When the motor is approved under various safety standards, the model name on the nameplate is the approved model name. Page H-11 Details of safety standards Page H-2 1 Single-Phase 22 VAC Hz type is not available for conduit box type. 2 Conduit box type is not certified under the China Compulsory Certification System (CCC System). : Contains a built-in thermal protector (automatic return type). If a motor overheats for any reason, the thermal protector is activated and the motor is stopped. When the motor temperature drops, the thermal protector closes and the motor restarts. Be sure to turn the motor power off before inspecting Rated Rated Speed 2 mn m oz-in r/min μf Reversible Electromagnetic Brake Clutch & Synchronous Brake Low-Speed Synchronous Watertight, Dust-Resistant Product Line Type Pinion Shaft Type Round Shaft Type IK4GN-AW2U IK4A-AW2U Lead Wire IK4GN-CW2E IK4A-CW2E IK4GN-SW2 IK4A-SW2 IK4GN-AW2TU IK4A-AW2TU Terminal Box IK4GN-CW2TE IK4A-CW2TE IK4GN-SW2T IK4A-SW2T IK4GN-FCH IK4AA-FCH Conduit Box IK4GN-ECH IK4AA-ECH IK4GN-SH IK4AA-SH The following items are included in each product.,, Cap, Operating Manual Only for single-phase motors (Excluding conduit box type) High Strength, Long Life, Low Noise Highest Maximum Permissible torque, 1, hours of life and quiet operation. For more details on see page C-149 or visit Parallel Shaft Gearhead/ Gearhead (Sold separately) Gearhead Type Gearhead Gear Ratio Parallel Shaft Shaft Parallel Shaft Long Life, Low Noise GN-S Gearhead Hollow Shaft Solid Shaft Long Life, Low Noise GN-S Gearhead GN SA 3, 3.6,, 6, 7., 9, 12., 1, 1, 2, 3, 36,, 6, 7, 9, GN RH 1, 12, 1, 1 GN RAA GN1XS (Decimal Gearhead) The following items are included in each product. Parallel Shaft Gearhead Gearhead, Mounting Screws, Operating Manual Hollow Shaft Gearhead Gearhead, Mounting Screws, Parallel Key, Safety Cover (with screws), Gasket, Operating Manual Solid Shaft Gearhead Gearhead, Mounting Screws, Gasket, Operating Manual The following gearheads are also available. For details, please refer to website ( or contact the nearest Oriental sales office. Gearhead Type Gearhead Gear Ratio Parallel GN KA 3 1 Shaft GN-K Gearhead GN1XK (Decimal Gearhead) Gearheads Linear Heads Brake Pack Accessories Installation CAD Data Manuals Technical Support TEL: () techsupport@orientalmotor.com C-41

24 Induction (1/7 HP, 1/2 HP) 1 W (1/ HP) 2 W (1/3 HP) 4 W 9 W 2 W 2-Pole 4-1 W (1/19-1/ HP) Gearmotor Table Enter the code that represents the terminal box type " T" in the box ( ) within the motor model name. Enter the gear ratio in the box ( ) within the gearhead model name. A colored background ( ) indicates gear shaft rotation in the same direction as the motor shaft, while the others rotate in the opposite direction. The speed is calculated by dividing the motor's synchronous speed ( Hz: 1 r/min, 6 Hz: 1 r/min) by the gear ratio. The actual speed is 2 2% less than the displayed value, depending on the load. To reduce the speed beyond the gear ratio in the table, attach a decimal gearhead (gear ratio 1:1) between the gearhead and the motor. In that case, the permissible torque is 1 N m ( lb-in). Hz Unit = Upper values: N m/lower values: lb-in Speed r/min / Gear Ratio Gearhead IK4GN-CW2 E (Single-phase 22 VAC) IK4GN-CW2 E IK4GN-ECH (Single-phase 23 VAC) IK4GN-SW2 IK4GN-SH 6 Hz / Gearhead IK4GN-AW2 U IK4GN-CW2 E IK4GN-SW2 IK4GN-FCH IK4GN-ECH IK4GN-SH GN SA GN SA Speed r/min Unit = Upper values: N m/lower values: lb-in Gear Ratio GN SA Gearmotor Table When Gearhead is Attached Page C Permissible Overhung Load and Permissible Thrust Load (Round shaft type) Page C-17 Gearhead Page C-17 Permissible Load Inertia J of Gearhead Page C-1 Dimensions Unit = mm (in.) Mounting screws are included with gearheads. Dimensions for mounting screws Page C-2 Lead Wire Type 1 Mass: 2. kg (. lb.) Gearhead 1. kg (3.3 lb.) ϕ9 (ϕ3.) 1 (4.13) 7. (.3) L 32 4 (1.26) (.16) 19 (.7) 11.4 (.4) ϕ ϕ..7 (1/2") 1 (.71) ϕ36 (ϕ1.42) 9 (3.4) 9 (3.4) 14±. (4.9±.2) Gearhead Gear Ratio L DXF IK4GN-AW2U IK4GN-CW2E IK4GN-SW2 Protective Earth Terminal M4 GN SA (.6) 42 (1.6) 6 (2.36) A42AU A42BU Leads 3 mm (12 in.) Length UL Style 3271, AWG2 4 ϕ6. (ϕ.26) Thru 22. (.2) max. 21. (.) Protective Earth Terminal M4 Detail Drawing of Protective Earth Terminal C-42 ORIENTAL MOTOR GENERAL CATALOG 212/213 Page Features C-2 / System Configuration C-23 / Specifications C-41 / Product Line C-41 Dimensions C-42 / Connection Diagrams C-26

25 Standard AC Terminal Box Type 2 Mass: 2.6 kg (.7 lb.) Gearhead 1. kg (3.3 lb.) 2 (1.1) max. 7 (2.9) 6 (.24) ϕ ϕ..7 (1/2") Gearhead Gear Ratio L DXF IK4GN-AW2TU IK4GN-CW2TE IK4GN-SW2T GN SA (2.) 42 (1.6) 6 (2.36) AAU ABU Introduction Induction ϕ9 (ϕ3.) 2 (.9) 19 (.7) 11.4 (.4) 1 (.71) ϕ36 (ϕ1.42) 9 (3.4) 43 (1.69) 14±. (4.9±.2) Reversible Electromagnetic Brake 7. (.3) 4 (.16) 4 ϕ6. (ϕ.26) Thru 1 (4.13) L 32 (1.26) Use cable with a diameter of ϕ6 ϕ12 mm (ϕ.24 ϕ.47 in.). Details of terminal box Page C-23 Shaft Section of Round Shaft Type The motor s dimensions (excluding the shaft section) are the same as those of the pinion shaft types. 2 (.) 37 (1.46) 3 (1.1) 9 (.3) ϕ1.1 (ϕ ) ϕ3.3 (ϕ ) 9 ( 3.4) 14±. (4.9±.2) Protective Earth Terminal M4 (Lead wire type only) 9 (3.4) Mass DXF IK4A-AW2U IK4A-CW2E IK4A-SW2 IK4A-AW2TU IK4A-CW2TE IK4A-SW2T 2. kg (. lb.) 2.6 kg (.7 lb.) A43 A33 Clutch & Synchronous Brake Low-Speed Synchronous Watertight, Dust-Resistant 4 ϕ6. (ϕ.26) Thru 22. (.2) max. Gearheads Linear Heads Brake Pack Accessories Installation CAD Data Manuals Technical Support TEL: () techsupport@orientalmotor.com C-43

26 Induction (1/7 HP, 1/2 HP) 1 W (1/ HP) 2 W (1/3 HP) Conduit Box Type 3 Gearhead Gear Ratio L DXF IK4GN-FCH GN SA IK4GN-ECH Mass: 2.7 kg (.9 lb.) Gearhead 1. kg (3.3 lb.) ϕ21. (ϕ.46) (2.17) 32 (1.26) 4 (2.13) 7 (2.9) ϕ9 (ϕ3.) (1.6) A92AU (2.36) A92BU 19 (.7) 11.4 (.4) ϕ ϕ..7 (1/2") 1 (.71) ϕ36 (ϕ1.42) 9 (3.4) 14±. (4.9±.2) 4 W 3 Leads: UL Style 3266, AWG2 1 Ground Lead: UL Style 3266, AWG1 Details of terminal box Page C-23 1 (4.13) 7. (.3) 4 (.16) L 32 (1.26) 4 ϕ6. (ϕ.26) Thru 9 (3.4) 9 W 2 W Gearhead Gear Ratio L DXF IK4GN-SH GN SA (1.6) A93AU (2.36) A93BU Mass: 2. kg (. lb.) Gearhead 1. kg (3.3 lb.) ϕ21. (ϕ.46) 4 (2.13) 7 (2.9) ϕ ϕ..7 (1/2") 2-Pole 4-1 W (1/19-1/ HP) 4 (1.77) 23 (.91) ϕ9 (ϕ3.) 19 (.7) 11.4 (.4) 1 (.71) ϕ36 (ϕ1.42) 9 (3.4) 14±. (4.9±.2) 3 Leads: UL Style 3266, AWG2 1 Ground Lead: UL Style 3266, AWG1 Details of terminal box Page C-23 1 (4.13) 7. (.3) 4 (.16) L 32 (1.26) 4 ϕ6. (ϕ.26) Thru 9 (3.4) Shaft Section of Round Shaft Type The motor s dimensions (excluding the shaft section) are the same as those of the pinion shaft types. Mass DXF IK4AA-FCH IK4AA-ECH 2.7 kg (.9 lb.) A11 Shaft Section of Round Shaft Type The motor s dimensions (excluding the shaft section) are the same as those of the pinion shaft types. Mass DXF IK4AA-SH 2. kg (. lb.) A12 37 (1.46) 2 (.) 3 (1.1).2 (.3) ϕ ϕ.37. (3/") ) ϕ3.3 ϕ (3.4) ( 14±. (4.9±.2) 37 (1.46) 2 (.) 3 (1.1).2 (.3) ϕ ϕ.37. (3/") ) ϕ3.3 ϕ (3.4) ( 14±. (4.9±.2) 4 ϕ6. (ϕ.26) Thru 9 (3.4) 4 ϕ6. (ϕ.26) Thru 9 (3.4) C- ORIENTAL MOTOR GENERAL CATALOG 212/213 Page Features C-2 / System Configuration C-23 / Specifications C-41 / Product Line C-41 Dimensions C-42 / Connection Diagrams C-26

27 Standard AC Decimal Gearhead Can be connected to GN pinion shaft type. GN1XS Mass:.6 kg (1.32 lb.) A22 (2.17) 37 (1.46) 2 (.) 1 (.71) Introduction Induction Reversible ϕ3.3 (ϕ ) 9 ( 3.4) 14±. (4.9±.2) Electromagnetic Brake 4 ϕ6. (ϕ.26) Thru (Included with single-phase motors) A ϕ4.3 (ϕ.169) AMP#17 2 (.79) B 4. (.1) 4 (.16) 1 C (.39) B+1 (.39) 6 (.24) Connection Diagrams Page C-26 Dimensions Unit = mm (in.) Upper Name: Pinion Shaft Type Lower Name ( ): Round Shaft Type Lead Wire Type Terminal Box Type IK4GN-AW2U (IK4A-AW2U) IK4GN-CW2E (IK4A-CW2E) IK4GN-AW2TU (IK4A-AW2TU) IK4GN-CW2TE (IK4A-CW2TE) CH9CFAUL2 CH23BFAUL A B C 4 (1.9) 4 (1.9) 22. (.9) 21 (.3) 31. (1.24) 31 (1.22) Mass g (oz.) 4 (1.9) 43 (1.2) Cap Included Clutch & Synchronous Brake Low-Speed Synchronous Watertight, Dust-Resistant Space-Saving Gearheads Page C-227 Gearhead, Accessories and Peripheral Equipment Instantaneous Stop Brake Pack Page C-23 Speed Control Speed Controller Page D-17 Accessories Page C-263 Gearheads Linear Heads Brake Pack Accessories Installation CAD Data Manuals Technical Support TEL: () techsupport@orientalmotor.com C-4

28 Induction (1/7 HP, 1/2 HP) Induction Frame Size: 9 mm ( 3.4 in.) Lead Wire Type Terminal Box Type (Gearhead sold separately) 1 W (1/ HP) 2 W (1/3 HP) 4 W 9 W 2 W 2-Pole 4-1 W (1/19-1/ HP) Specifications Continuous Rating Lead Wire Type Dimension 1 IK6GE-AW2U (IK6A-AW2U) IK6GE-CW2E (IK6A-CW2E) IK6GE-SW2 (IK6A-SW2) Upper Name: Pinion Shaft Type Lower Name ( ): Round Shaft Type Terminal Box Type Dimension 2 IK6GE-AW2TU (IK6A-AW2TU) IK6GE-CW2TE (IK6A-CW2TE) IK6GE-SW2T (IK6A-SW2T) Conduit Box Type Dimension 3 IK6GE-FCH (IK6A-FCH) Output Power IK6GE-ECH 1 6 (IK6A-ECH) 1 1/12 IK6GE-SH (IK6A-SH) Voltage Frequency Current W HP VAC Hz A 6 Single-Phase /12 Single-Phase /12 Single-Phase 22 Single-Phase 23 Three-Phase Three-Phase Three-Phase Starting mn m oz-in The U and E at the end of the model name indicate that the unit includes a capacitor. These letters are not listed on the motor nameplate. When the motor is approved under various safety standards, the model name on the nameplate is the approved model name. Page H-11 Details of safety standards Page H-2 1 Single-Phase 22 VAC Hz type is not available for conduit box type. 2 Conduit box type is not certified under the China Compulsory Certification System (CCC System). : Contains a built-in thermal protector (automatic return type). If a motor overheats for any reason, the thermal protector is activated and the motor is stopped. When the motor temperature drops, the thermal protector closes and the motor restarts. Be sure to turn the motor power off before inspecting Rated Rated Speed 2 mn m oz-in r/min μf Product Line Type Pinion Shaft Type Round Shaft Type IK6GE-AW2U IK6A-AW2U Lead Wire IK6GE-CW2E IK6A-CW2E IK6GE-SW2 IK6A-SW2 IK6GE-AW2TU IK6A-AW2TU Terminal Box IK6GE-CW2TE IK6A-CW2TE IK6GE-SW2T IK6A-SW2T IK6GE-FCH IK6A-FCH Conduit Box IK6GE-ECH IK6A-ECH IK6GE-SH IK6A-SH The following items are included in each product.,, Cap, Operating Manual Only for single-phase motors (Excluding conduit box type) Parallel Shaft Gearhead/ Gearhead (Sold separately) Gearhead Type Gearhead Gear Ratio Parallel Shaft Shaft Parallel Shaft Long Life GE-S Gearhead Hollow Shaft Solid Shaft Long Life GE-S Gearhead GE SA 3, 3.6,, 6, 7., 9, 12., 1, 1, 2, 3, 36,, 6, 7, 9, GE RH 1, 12, 1, 1 GE RAA GE1XS (Decimal Gearhead) The following items are included in each product. Parallel Shaft Gearhead Gearhead, Mounting Screws, Parallel Key, Operating Manual Hollow Shaft Gearhead Gearhead, Mounting Screws, Parallel Key, Safety Cover (with screws), Gasket, Operating Manual Solid Shaft Gearhead Gearhead, Mounting Screws, Parallel Key, Gasket, Operating Manual High Strength, Long Life, Low Noise Highest Maximum Permissible torque, 1, hours of life and quiet operation. For more details on see page C-149 or visit C-46 ORIENTAL MOTOR GENERAL CATALOG 212/213 Page Features C-2 / System Configuration C-23 / Specifications C-46 / Product Line C-46 Dimensions C-47 / Connection Diagrams C-26

29 Standard AC Gearmotor Table Enter the code that represents the terminal box type " T" in the box ( ) within the motor model name. Enter the gear ratio in the box ( ) within the gearhead model name. A colored background ( ) indicates gear shaft rotation in the same direction as the motor shaft, while the others rotate in the opposite direction. The speed is calculated by dividing the motor's synchronous speed ( Hz: 1 r/min, 6 Hz: 1 r/min) by the gear ratio. The actual speed is 2 2% less than the displayed value, depending on the load. To reduce the speed beyond the gear ratio in the table, attach a decimal gearhead (gear ratio 1:1) between the gearhead and the motor. In that case, the permissible torque is 2 N m ( lb-in). Hz Unit = Upper values: N m/lower values: lb-in Speed r/min / Gear Ratio Gearhead IK6GE-CW2 E IK6GE-ECH IK6GE-SW2 IK6GE-SH 6 Hz / Gearhead IK6GE-AW2 U IK6GE-CW2 E IK6GE-FCH IK6GE-ECH IK6GE-SW2 IK6GE-SH GE SA GE SA Speed r/min Unit = Upper values: N m/lower values: lb-in Gear Ratio GE SA GE SA Gearmotor Table When Gearhead is Attached Page C-23 Permissible Overhung Load and Permissible Thrust Load (Round shaft type) Page C-17 Gearhead Page C-17 Permissible Load Inertia J of Gearhead Page C-1 Dimensions Unit = mm (in.) Mounting screws are included with gearheads. Dimensions for mounting screws Page C-2 Lead Wire Type 1 Mass: 2.7 kg (.9 lb.) Gearhead 1. kg (3.3 lb.) 9 ( 3.4) 12 (4.72) 7. (.3) 6 (2.6) 3 (1.) 7 (.2) 29.±. (1.16±.2) 2. (1.12) Leads 3 mm (12 in.) Length UL Style 3271, AWG ϕ ϕ.62.4 (/") ϕ17 (ϕ.67) 1 (.71) ϕ34 (ϕ1.34) No.1-24UNC 1 (.39) Deep 9 (3.4) 4 ϕ6. (ϕ.26) Thru (3.4) Gearhead DXF IK6GE-AW2U IK6GE-CW2E IK6GE-SW2 GE SA A4U 14±. (4.9±.2) Protective Earth Terminal M4 (.2) max. 21. (.) 2 2 Protective Earth Terminal M4 16. (.6) Detail Drawing of Protective Earth Terminal Introduction Induction Reversible Electromagnetic Brake Clutch & Synchronous Brake Low-Speed Synchronous Watertight, Dust-Resistant Gearheads Linear Heads Brake Pack Accessories Installation CAD Data Manuals Technical Support TEL: () techsupport@orientalmotor.com C-47

30 Induction (1/7 HP, 1/2 HP) Terminal Box Type 2 Mass: 2. kg (6.2 lb.) Gearhead 1. kg (3.3 lb.) Gearhead DXF IK6GE-AW2TU IK6GE-CW2TE IK6GE-SW2T GE SA A47U 1 W (1/ HP) 2 (1.1) max. 2 (.9) 7 (2.9) 6 (.24) 29.±. (1.16±.2) 2. (1.13) ϕ ϕ.62.4 (/") ϕ17 (ϕ.67) 1 (.71) ϕ34 (ϕ1.34) 62 (2.) 43 (1.69) 2 W (1/3 HP) 9 ( 3.4) No.1-24UNC 1 (.39) Deep 9 (3.4) 4 W 7. (.3) 12 (4.72) 7 (.2) 6 (2.6) 3 (1.) 14±. (4.9±.2) 4 ϕ6. (ϕ.26) Thru 9 (3.4) Use cable with a diameter of ϕ6 ϕ12 mm (ϕ.24 ϕ.47 in.). Details of terminal box Page C-23 Key and Key Slot (The key is included with the gearhead) 9 W 2 W 2.±.2 (1.12±.) ( ) ( ) (.17 ) (.1 ) 2-Pole 4-1 W (1/19-1/ HP) Shaft Section of Round Shaft Type The motor s dimensions (excluding the shaft section) are the same as those of the pinion shaft types. 2 (.) 37 (1.46) 3 (1.1) 11 (.43) ϕ12.1 (ϕ ) ϕ3.3 (ϕ ) 9 ( 3.4) 14±. (4.9±.2) Protective Earth Terminal M4 (Lead wire type only) Mass DXF IK6A-AW2U IK6A-CW2E IK6A-SW2 IK6A-AW2TU IK6A-CW2TE IK6A-SW2T 2.7 kg (.9 lb.) 2. kg (6.2 lb.) A46 A332 4 ϕ6. (ϕ.26) Thru (.2) max. 22. C-4 ORIENTAL MOTOR GENERAL CATALOG 212/213 Page Features C-2 / System Configuration C-23 / Specifications C-46 / Product Line C-46 Dimensions C-47 / Connection Diagrams C-26

31 Standard AC Conduit Box Type 3 Gearhead DXF IK6GE-FCH IK6GE-ECH GE SA A94U Introduction Mass: 3.2 kg (7. lb.) Gearhead 1. kg (3.3 lb.) ϕ21. (ϕ.46) 6 (2.6) 31 (1.22) 74 (2.91) 3 Leads: UL Style 3266, AWG2 1 Ground Lead: UL Style 3266, AWG1 Details of terminal box Page C-23 9 ( 3.4) Key and Key Slot (The key is included with the gearhead) 2.±.2 (1.12±.) ( ) ( ) (.17 ) 1 (3.94) 7. (.3) 12 (4.72) (.1 ) 7 (.2) 6 (2.6) 3 (1.) 29.±. (1.16±.2) 2. (1.13) ϕ ϕ.62.4 (/") ϕ17 (ϕ.67) 1 (.71) ϕ34 (ϕ1.34) No.1-24UNC 1 (.39) Deep 14±. (4.9±.2) 9 (3.4) 4 ϕ6. (ϕ.26) Thru 9 (3.4) Induction Reversible Electromagnetic Brake Clutch & Synchronous Brake Low-Speed Synchronous Gearhead DXF IK6GE-SH GE SA A9U Mass: 2. kg (6.2 lb.) Gearhead 1.kg (3.3 lb.) ϕ21. (ϕ.46) 4 (2.13) 7 (2.9) ϕ ϕ.62.4 (/") Watertight, Dust-Resistant 4 (1.77) 23 (.91) 3 Leads: UL Style 3266, AWG2 1 Ground Lead: UL Style 3266, AWG1 Details of terminal box Page C-23 9 ( 3.4) Key and Key Slot (The key is included with the gearhead) 2.±.2 (1.12±.) ( ) ( ) (.17 ) 7. (.3) 12 (4.72) (.1 ) 7 (.2) 6 (2.6) 3 (1.) 29.±. (1.16±.2) 2. (1.13) ϕ17 (ϕ.67) 1 (.71) ϕ34 (ϕ1.34) No.1-24UNC 1 (.39) Deep 14±. (4.9±.2) 9 (3.4) 4 ϕ6. (ϕ.26) Thru 9 (3.4) Gearheads Linear Heads Brake Pack Accessories Installation CAD Data Manuals Technical Support TEL: () techsupport@orientalmotor.com C-49

32 Induction (1/7 HP, 1/2 HP) Shaft Section of Round Shaft Type The motor s dimensions (excluding the shaft section) are the same as those of the pinion shaft types. Mass DXF IK6A-FCH IK6A-ECH 3.2 kg (7. lb.) A13 74 (2.91) Shaft Section of Round Shaft Type The motor s dimensions (excluding the shaft section) are the same as those of the pinion shaft types. Mass DXF IK6A-SH 2. kg (6.2 lb.) A14 1 W (1/ HP) ϕ12.1 ϕ ( ) 6 (2.6) ϕ12.1 ϕ ( ) 2 W (1/3 HP) 4 W 9 W 3 (1.1) 2 (.) 37 (1.46) 11(.43) 4 ϕ6. (ϕ.26) Thru Decimal Gearhead Can be connected to GE pinion shaft type. GE1XS Mass:.6 kg (1.32 lb.) A29 ϕ3.3 ) ϕ ( 9 (3.4) 9 (3.4) 14±. (4.9±.2) 3 (1.1) 2 (.) 37 (1.46) 11 (.43) ϕ3.3 ) 61 (2.4) 2 W 4 (1.7) 21 (.3) 2 (.) 2-Pole 4-1 W (1/19-1/ HP) ϕ3.3 (ϕ ) 9 ( 3.4) 14±. (4.9±.2) 4 ϕ1. (ϕ.42) Thru (Included with single-phase motors) A ϕ4.3 (ϕ.169) AMP#17 2 (.79) C B 7 (.2) 1 (.39) 6 (.24) 4 (.16) ϕ ( 9 (3.4) 4 ϕ6. (ϕ.26) Thru 9 (3.4) 14±. (4.9±.2) B+1 (.9) R1 (R.39) Dimensions Unit = mm (in.) Upper Name: Pinion Shaft Type Lower Name ( ): Round Shaft Type Lead Wire Type Terminal Box Type IK6GE-AW2U (IK6A-AW2U) IK6GE-CW2E (IK6A-CW2E) IK6GE-AW2TU (IK6A-AW2TU) IK6GE-CW2TE (IK6A-CW2TE) CH1CFAUL2 CH4BFAUL A B C (2.2) (2.2) 29 (1.14) 23. (.93) 41 (1.61) 37 (1.46) Mass g (oz.) 92 (3.2) 73 (2.6) Cap Included C- ORIENTAL MOTOR GENERAL CATALOG 212/213 Page Features C-2 / System Configuration C-23 / Specifications C-46 / Product Line C-46 Dimensions C-47 / Connection Diagrams C-26

33 Standard AC Connection Diagrams Page C-26 Space-Saving Gearheads Page C-227 Gearhead, Accessories and Peripheral Equipment Instantaneous Stop Brake Pack Page C-23 Speed Control Speed Controller Page D-17 Accessories Page C-263 Introduction Induction Reversible Electromagnetic Brake Clutch & Synchronous Brake Low-Speed Synchronous Watertight, Dust-Resistant Gearheads Linear Heads Brake Pack Accessories Installation CAD Data Manuals Technical Support TEL: () C-1

34 Induction (1/7 HP, 1/2 HP) Induction 9 W Frame Size: 9 mm ( 3.4 in.) Lead Wire Type Terminal Box Type (Gearhead sold separately) 1 W (1/ HP) 2 W (1/3 HP) 4 W 9 W 2 W 2-Pole 4-1 W (1/19-1/ HP) Specifications Continuous Rating Lead Wire Type Dimension 1 IK9GE-AW2U (IK9A-AW2U) IK9GE-CW2E (IK9A-CW2E) IK9GE-SW2 (IK9A-SW2) Upper Name: Pinion Shaft Type Lower Name ( ): Round Shaft Type Terminal Box Type Dimension 2 IK9GE-AW2TU (IK9A-AW2TU) IK9GE-CW2TE (IK9A-CW2TE) IK9GE-SW2T (IK9A-SW2T) Conduit Box Type Dimension 3 IK9GE-FCH (IK9A-FCH) Output Power IK9GE-ECH 1 9 (IK9A-ECH) 1 1/ IK9GE-SH (IK9A-SH) Voltage Frequency Current W HP VAC Hz A 9 Single-Phase / Single-Phase / Single-Phase 22 Single-Phase 23 Three-Phase Three-Phase Three-Phase Starting mn m oz-in The U and E at the end of the model name indicate that the unit includes a capacitor. These letters are not listed on the motor nameplate. When the motor is approved under various safety standards, the model name on the nameplate is the approved model name. Page H-11 Details of safety standards Page H-2 1 Single-Phase 22 VAC Hz type is not available for conduit box type. 2 Conduit box type is not certified under the China Compulsory Certification System (CCC System). : Contains a built-in thermal protector (automatic return type). If a motor overheats for any reason, the thermal protector is activated and the motor is stopped. When the motor temperature drops, the thermal protector closes and the motor restarts. Be sure to turn the motor power off before inspecting Rated Rated Speed 2 mn m oz-in r/min μf Product Line Type Pinion Shaft Type Round Shaft Type IK9GE-AW2U IK9A-AW2U Lead Wire IK9GE-CW2E IK9A-CW2E IK9GE-SW2 IK9A-SW2 IK9GE-AW2TU IK9A-AW2TU Terminal Box IK9GE-CW2TE IK9A-CW2TE IK9GE-SW2T IK9A-SW2T IK9GE-FCH IK9A-FCH Conduit Box IK9GE-ECH IK9A-ECH IK9GE-SH IK9A-SH The following items are included in each product.,, Cap, Operating Manual Only for single-phase motors (Excluding conduit box type) Parallel Shaft Gearhead/ Gearhead (Sold separately) Gearhead Type Gearhead Gear Ratio Parallel Shaft Shaft Parallel Shaft Long Life GE-S Gearhead Hollow Shaft Solid Shaft Long Life GE-S Gearhead GE SA 3, 3.6,, 6, 7., 9, 12., 1, 1, 2, 3, 36,, 6, 7, 9, GE RH 1, 12, 1, 1 GE RAA GE1XS (Decimal Gearhead) The following items are included in each product. Parallel Shaft Gearhead Gearhead, Mounting Screws, Parallel Key, Operating Manual Hollow Shaft Gearhead Gearhead, Mounting Screws, Parallel Key, Safety Cover (with screws), Gasket, Operating Manual Solid Shaft Gearhead Gearhead, Mounting Screws, Parallel Key, Gasket, Operating Manual High Strength, Long Life, Low Noise Highest Maximum Permissible torque, 1, hours of life and quiet operation. For more details on see page C-149 or visit C-2 ORIENTAL MOTOR GENERAL CATALOG Page Features C-2 / System Configuration C-23 / Specifications C-2 / Product Line C-2 212/213 Dimensions C-3 / Connection Diagrams C-26

35 Standard AC Gearmotor Table Enter the code that represents the terminal box type " T" in the box ( ) within the motor model name. Enter the gear ratio in the box ( ) within the gearhead model name. A colored background ( ) indicates gear shaft rotation in the same direction as the motor shaft, while the others rotate in the opposite direction. The speed is calculated by dividing the motor's synchronous speed ( Hz: 1 r/min, 6 Hz: 1 r/min) by the gear ratio. The actual speed is 2 2% less than the displayed value, depending on the load. To reduce the speed beyond the gear ratio in the table, attach a decimal gearhead (gear ratio 1:1) between the gearhead and the motor. In that case, the permissible torque is 2 N m ( lb-in). Hz Unit = Upper values: N m/lower values: lb-in Speed r/min / Gear Ratio Gearhead IK9GE-CW2 E IK9GE-ECH IK9GE-SW2 IK9GE-SH 6 Hz / Gearhead IK9GE-AW2 U IK9GE-FCH IK9GE-CW2 E IK9GE-ECH IK9GE-SW2 IK9GE-SH GE SA GE SA Speed r/min Unit = Upper values: N m/lower values: lb-in Gear Ratio GE SA GE SA GE SA Gearmotor Table When Gearhead is Attached Page C-23 Permissible Overhung Load and Permissible Thrust Load (Round shaft type) Page C-17 Gearhead Page C Permissible Load Inertia J of Gearhead Page C-1 Dimensions Unit = mm (in.) Mounting screws are included with gearheads. Dimensions for mounting screws Page C-2 Lead Wire Type 1 Gearhead DXF Mass: 3.2 kg (7. lb.) Gearhead 1. kg (3.3 lb.) 9 ( 3.4) 13 (.31) 7. (.3) 6 (2.6) 3 (1.) 7 (.2) 29.±. (1.16±.2) 2. (1.13) Leads 3 mm (12 in.) Length UL Style 3271, AWG ϕ ϕ.62.4 (/") ϕ17 (ϕ.67) 1 (.71) ϕ34 (ϕ1.34) No.1-24UNC 1 (.39) Deep 9 (3.4) 4 ϕ6. (ϕ.26) Thru IK9GE-AW2U IK9GE-CW2E IK9GE-SW2 9 (3.4) ±. (4.9±.2) Protective Earth Terminal M4 (.2) max GE SA (.) A4U Protective Earth Terminal M (.6) Detail Drawing of Protective Earth Terminal Introduction Induction Reversible Electromagnetic Brake Clutch & Synchronous Brake Low-Speed Synchronous Watertight, Dust-Resistant Gearheads Linear Heads Brake Pack Accessories Installation CAD Data Manuals Technical Support TEL: () techsupport@orientalmotor.com C-3

36 Induction (1/7 HP, 1/2 HP) Terminal Box Type 2 Mass: 3.3 kg (7.3 lb.) Gearhead 1. kg (3.3 lb.) Gearhead DXF IK9GE-AW2TU IK9GE-CW2TE IK9GE-SW2T GE SA A46U 1 W (1/ HP) 2 (.9) 2 (1.1) max. 7 (2.9) 6 (.24) 29.±. (1.16±.2) 2. (1.13) ϕ (2.) ϕ.62.4 (/") ϕ17 (ϕ.67) 1 (.71) ϕ34 (ϕ1.34) 43 (1.69) 2 W (1/3 HP) 9 ( 3.4) No.1-24UNC 1 (.39) Deep 9 (3.4) 4 W 7. (.3) 7 (.2) 13 (.31) 6 (2.6) 3 (1.) Use cable with a diameter of ϕ6 ϕ12 mm (ϕ.24 ϕ.47 in.). Details of terminal box Page C-23 Key and Key Slot (The key is included with the gearhead) 14±. (4.9±.2) 4 ϕ6. (ϕ.26) Thru 9 (3.4) 9 W 2.±.2 (1.12±.) ( ) ( ) (.17 ) (.1 ) 2 W 2-Pole 4-1 W (1/19-1/ HP) Shaft Section of Round Shaft Type The motor s dimensions (excluding the shaft section) are the same as those of the pinion shaft types. 2 (.) 37 (1.46) 3 (1.1) 11 (.43) ϕ12.1 (ϕ ) ϕ3.3 (ϕ ) 9 ( 3.4) 14±. (4.9±.2) Protective Earth Terminal M4 (Lead wire type only) Mass DXF IK9A-AW2U IK9A-CW2E IK9A-SW2 IK9A-AW2TU IK9A-CW2TE IK9A-SW2T 3.2 kg (7. lb.) 3.3 kg (7.3 lb.) A49 A334 4 ϕ6. (ϕ.26) Thru (.2) max. 22. C-4 ORIENTAL MOTOR GENERAL CATALOG Page Features C-2 / System Configuration C-23 / Specifications C-2 / Product Line C-2 212/213 Dimensions C-3 / Connection Diagrams C-26

37 Standard AC Conduit Box Type 3 Gearhead DXF IK9GE-FCH IK9GE-ECH GE SA A96U Introduction Mass: 3.7 kg (.1 lb.) Gearhead 1. kg (3.3 lb.) ϕ21. (ϕ.46) 6 (2.6) 31 (1.22) 74 (2.91) 3 Leads: UL Style 3266, AWG2 1 Ground Lead: UL Style 3266, AWG1 Details of terminal box Page C-23 9 ( 3.4) Key and Key Slot (The key is included with the gearhead) 2.±.2 (1.12±.) ( ) ( ) (.17 ) 1 (3.94) 7. (.3) 13 (.31) (.1 ) 7 (.2) 6 (2.6) 3 (1.) ϕ ϕ.62.4 (/") 29.±. (1.16±.2) 2. (1.13) ϕ17 (ϕ.67) 1 (.71) ϕ34 (ϕ1.34) No.1-24UNC 1 (.39) Deep 14±. (4.9±.2) 9 (3.4) 4 ϕ6. (ϕ.26) Thru 9 (3.4) Induction Reversible Electromagnetic Brake Clutch & Synchronous Brake Low-Speed Synchronous Gearhead DXF IK9GE-SH GE SA A97U Mass: 3.3 kg (7.3 lb.) Gearhead 1. kg (3.3 lb.) ϕ21. 4 (2.13) (ϕ.46) 4 (1.77) 23 (.91) 3 Leads: UL Style 3266, AWG2 1 Ground Lead: UL Style 3266, AWG1 Details of terminal box Page C-23 9 ( 3.4) Key and Key Slot (The key is included with the gearhead) 2.±.2 (1.12±.) ( ) ( ) (.17 ) 7 (2.9) 7. (.3) 13 (.31) (.1 ) 7 (.2) 6 (2.6) 3 (1.) ϕ ϕ.62.4 (/") 29.±. (1.16±.2) 2. (1.13) ϕ17 (ϕ.67) 1 (.71) ϕ34 (ϕ1.34) No.1-24UNC 1 (.39) Deep 14±. (4.9±.2) 9 (3.4) 4 ϕ6. (ϕ.26) Thru 9 (3.4) Watertight, Dust-Resistant Gearheads Linear Heads Brake Pack Accessories Installation CAD Data Manuals Technical Support TEL: () techsupport@orientalmotor.com C-

38 Induction (1/7 HP, 1/2 HP) Shaft Section of Round Shaft Type The motor s dimensions (excluding the shaft section) are the same as those of the pinion shaft types. Mass DXF IK9A-FCH IK9A-ECH 3.7 kg (.1 lb.) A1 74 (2.91) Shaft Section of Round Shaft Type The motor s dimensions (excluding the shaft section) are the same as those of the pinion shaft types. Mass DXF IK9A-SH 3.3 kg (7.3 lb.) A16 1 W (1/ HP) 2 W (1/3 HP) 4 W 37 (1.46) 2 (.) 3 (1.1) 11 (.43) ϕ12.1 ϕ ( ϕ3.3 ) ϕ ( ) 9 (3.4) 6 (2.6) 14±. (4.9±.2) 37 (1.46) 2 (.) 3 (1.1) 11(.43) ϕ12.1 ϕ ( ϕ3.3 ) 9 W 2 W Decimal Gearhead Can be connected to GE pinion shaft type. GE1XS Mass:.6 kg (1.32 lb.) A29 61 (2.4) 4 (1.7) 21 2 (.3) (.) 2-Pole 4-1 W (1/19-1/ HP) ϕ3.3 (ϕ ) 9 ( 3.4) 14±. (4.9±.2) 4 ϕ1. (ϕ.42) Thru (Included with single-phase motors) A ϕ4.3 (ϕ.169) AMP#17 2 (.79) C B 7 (.2) 1 (.39) 6 (.24) 4 (.16) ϕ ( ) 9 (3.4) 14±. (4.9±.2) 4 ϕ6. (ϕ.26) Thru 9 (3.4) 4 ϕ6. (ϕ.26) Thru 9 (3.4) B+1 (.9) R1 (R.39) Dimensions Unit = mm (in.) Upper Name: Pinion Shaft Type Lower Name ( ): Round Shaft Type Lead Wire Type Terminal Box Type IK9GE-AW2U (IK9A-AW2U) IK9GE-CW2E (IK9A-CW2E) IK9GE-AW2TU (IK9A-AW2TU) IK9GE-CW2TE (IK9A-CW2TE) CH2CFAUL2 CH6BFAUL A B C (2.2) (2.2) 29 (1.14) 29 (1.14) 41 (1.61) 41 (1.61) Mass g (oz.) 91 (3.2) 92 (3.2) Cap Included C-6 ORIENTAL MOTOR GENERAL CATALOG Page Features C-2 / System Configuration C-23 / Specifications C-2 / Product Line C-2 212/213 Dimensions C-3 / Connection Diagrams C-26

39 Standard AC Connection Diagrams Page C-26 Space-Saving Gearheads Page C-227 Gearhead, Accessories and Peripheral Equipment Instantaneous Stop Brake Pack Page C-23 Speed Control Speed Controller Page D-17 Accessories Page C-263 Introduction Induction Reversible Electromagnetic Brake Clutch & Synchronous Brake Low-Speed Synchronous Watertight, Dust-Resistant Gearheads Linear Heads Brake Pack Accessories Installation CAD Data Manuals Technical Support TEL: () C-7

40 Induction (1/7 HP, 1/2 HP) High Power Induction BH Series 2 W Frame Size: 14 mm ( 4.9 in.) Cable Type Hollow Shaft Terminal Box Type Parallel Shaft 1 W (1/ HP) 2 W (1/3 HP) 4 W Features High Power 2 W Smallest frame size among 2 W motors Hypoid Gear Gearheads Right-angle gearheads employ hypoid gears. Hollow shafts and solid shafts are available to enable space-saving. Tapped Hole at the Shaft End The gearhead shafts feature a tapped hole for convenient connection with loads. "Combination Type" for Easy Installation The combination type comes with the motor and gearhead pre-assembled. This enables easy installation in equipment. Combination Type: The combination type comes with the motor and its dedicated gearhead pre-assembled which simplifies installation in equipment. and gearheads are also available separately to facilitate changes or repairs. 9 W 2 W 2-Pole 4-1 W (1/19-1/ HP) Specifications Continuous Rating Combination Type ( ) : Round Shaft Type Cable Type Terminal Box Type BHI62F- RH BHI62F- RA BHI62F- (BHI62F-A) BHI62E- RH BHI62E- RA BHI62E- (BHI62E-A) BHI62S- RH BHI62S- RA BHI62S- (BHI62S-A) BHI62FT- RH BHI62FT- RA BHI62FT- (BHI62FT-A) BHI62ET- RH BHI62ET- RA BHI62ET- (BHI62ET-A) BHI62ST- RH BHI62ST- RA BHI62ST- (BHI62ST-A) Output Power W HP VAC Hz A 2 1/4 2 1/4 2 1/4 Voltage Frequency Current Starting Rated Rated Speed Single-Phase 11 Single-Phase 11 Single-Phase 22 Single-Phase 23 Three-Phase Three-Phase 22 6 Three-Phase N m oz-in N m oz-in r/min μf The values for each specification applies to the motor only. Details of safety standards Page H-2 For detailed product safety standard information including standards, file number and certification body, please visit : Contains a built-in thermal protector (automatic return type). If a motor overheats for any reason, the thermal protector is activated and the motor is stopped. When the motor temperature drops, the thermal protector closes and the motor restarts. Be sure to turn the motor power off before inspecting. Product Line Combination Type Shaft Type Voltage Gear Ratio Single-Phase 11/11 VAC BHI62F- RH Hollow Shaft Single-Phase 22/23 VAC BHI62E- RH Cable Three-Phase 2/22/23 VAC BHI62S- RH Single-Phase 11/11 VAC BHI62FT- RH Hollow Shaft Single-Phase 22/23 VAC BHI62ET- RH Terminal Box, 6, 7., 9, 12., Three-Phase 2/22/23 VAC BHI62ST- RH 1, 1, 2, 3, 36, Single-Phase 11/11 VAC BHI62F- RA, 6, 7, 9, 1, Solid Shaft Single-Phase 22/23 VAC BHI62E- RA 12, 1, 1 Cable Three-Phase 2/22/23 VAC BHI62S- RA Single-Phase 11/11 VAC BHI62FT- RA Solid Shaft Single-Phase 22/23 VAC BHI62ET- RA Terminal Box Three-Phase 2/22/23 VAC BHI62ST- RA The following items are included in each product., Gearhead,, Cap, Parallel Key, Operating Manual Only for single-phase motors 1 C- ORIENTAL MOTOR GENERAL CATALOG 212/213 Page Features C-2 / System Configuration C-23 / Specifications C- / Product Line C- Dimensions C-6 / Connection Diagrams C-67 / and Gearhead Combinations C-69

41 Standard AC Parallel Shaft Type Voltage Gear Ratio Single-Phase 11/11 VAC BHI62F- Parallel Shaft Single-Phase 22/23 VAC BHI62E- Cable 3, 3.6,, 6, 7., 9, 12., 1, Three-Phase 2/22/23 VAC BHI62S- 1, 2, 3, 36,, 6, 7, Single-Phase 11/11 VAC BHI62FT- Parallel Shaft 9, 1, 12, 1, 1 Single-Phase 22/23 VAC BHI62ET- Terminal Box Three-Phase 2/22/23 VAC BHI62ST- The following items are included in each product., Gearhead,, Cap, Mounting Screws, Parallel Key, Operating Manual Only for single-phase motors Gearmotor Table for Combination Type Round Shaft Type Type Voltage Single-Phase 11/11 VAC BHI62F-A Cable Single-Phase 22/23 VAC BHI62E-A Three-Phase 2/22/23 VAC BHI62S-A Single-Phase 11/11 VAC BHI62FT-A Terminal Box Single-Phase 22/23 VAC BHI62ET-A Three-Phase 2/22/23 VAC BHI62ST-A The following items are included in each product.,, Cap, Operating Manual Only for single-phase motors Enter the code that represents the terminal box type T in the box ( ) within the model name. Enter the gear ratio in the box ( ) within the model name. A colored background ( ) indicates gear shaft rotation in the same direction as the motor shaft, while the others rotate in the opposite direction. The speed is calculated by dividing the motor's synchronous speed ( Hz: 1 r/min, 6 Hz: 1 r/min) by the gear ratio. The actual speed is 2 2% less than the displayed value, depending on the load. Decimal gearheads are not available for the BH series. Shaft Hz Unit = Upper values: N m/lower values: lb-in Speed r/min Gear Ratio BHI62E - RH, BHI62E - RA BHI62S - RH, BHI62S - RA Shaft 6 Hz Unit = Upper values: N m/lower values: lb-in Speed r/min Gear Ratio BHI62F - RH, BHI62F - RA BHI62E - RH, BHI62E - RA BHI62S - RH, BHI62S - RA (2 VAC) BHI62S - RH, BHI62S - RA (22 VAC) BHI62S - RH, BHI62S - RA (23 VAC) Parallel Shaft Hz Unit = Upper values: N m/lower values: lb-in Speed r/min Gear Ratio BHI62E - BHI62S Parallel Shaft 6 Hz Unit = Upper values: N m/lower values: lb-in Speed r/min Gear Ratio BHI62F -, BHI62E - BHI62S - (2 VAC) BHI62S - (22 VAC) BHI62S - (23 VAC) Introduction Induction Reversible Electromagnetic Brake Clutch & Synchronous Brake Low-Speed Synchronous Watertight, Dust-Resistant Gearheads Linear Heads Brake Pack Accessories Installation CAD Data Manuals Technical Support TEL: () techsupport@orientalmotor.com C-9

42 Induction (1/7 HP, 1/2 HP) 1 W (1/ HP) Permissible Overhung Load and Permissible Thrust Load Combination Type Page C-17 Round Shaft Type Page C-17 Permissible Load Inertia J of Gearhead Page C-1 Dimensions Unit = mm (in.) Mounting screws are included with the combination type, parallel shaft. Dimensions for mounting screws Page C-2 2 W (1/3 HP) 4 W Combination Type:, Hollow Shaft (Cable Type) BHI62F- RH, BHI62E- RH, BHI62S- RH Mass: 1. kg (22 lb.) : BHI62F-G2, BHI62E-G2, BHI62S-G2 Gearhead: BH6G2- RH A299 Key (Included) (.94. ).36 (.31.14) ( ) 16 (6.3) Protective Earth Terminal M4 (2.4) 14 (6.6) 19.3 (4.3) 3 (1.1) 1 (.9) 1. (.6) 3 (1.1) 1 (.9) 1. (.6) 9 W 2 W 2-Pole 4-1 W (1/19-1/ HP) 13 ( 4.6) 2. (.1) Cable ϕ7. (ϕ.31), mm (2 in.) Length UL Style 3271, AWG2 32. (1.2) 12 (4.2) +.4 ϕ4 (ϕ1.7) 16 (.63) 99 (3.9) 11 (4.6) 4 (.16) ϕ.46 (ϕ2.23.1) (.943 ) ±. (.31 ) (4.72±.2) 4. (.19) Flange Mounting Surface A A 14 (.) Groove for Retaining Ring ϕ26.2 (ϕ1.3 ) 27 (1.6) A 2.3 (1.11) 14 (4.9) A 14 (4.9) 4 ϕ. (ϕ.33) Thru 66 (2.6) C-6 ORIENTAL MOTOR GENERAL CATALOG 212/213 Page Features C-2 / System Configuration C-23 / Specifications C- / Product Line C- Dimensions C-6 / Connection Diagrams C-67 / and Gearhead Combinations C-69

43 Standard AC Combination Type:, Solid Shaft (Cable Type) BHI62F- RA, BHI62E- RA, BHI62S- RA Mass: 1. kg (22 lb.) : BHI62F-G2, BHI62E-G2, BHI62S-G2 Gearhead: BH6G2- RA A3 16 (6.3) 14 (6.6) Protective Earth (2.4) Terminal M4 Introduction Induction 13 ( 4.6) 2. (.1) Reversible Electromagnetic Brake Cable ϕ7.(ϕ.31), mm (2 in.) Length UL Style 3271, AWG2 12±. (4.72±.2) 14 (.) 27 (1.6) Clutch & Synchronous Brake 14 (4.9) 16 (.63) 99 (3.9) 11 (4.6) 32. (1.2) 12 (4.2) M6 12 (.47) Deep 32 (1.26) 4±. (1.7±.2) 4 (.16) 4 (1.9) ϕ22.21 (ϕ.661.) 24. (.96) ϕ.46 (ϕ2.23.1) Low-Speed Synchronous 14 (4.9) 4 ϕ. (ϕ.33) Thru 66 (2.6) Watertight, Dust-Resistant Key and Key Slot (Included) 32±.2 (1.26±.) 6.3 ( ) 6.3 ( ) 1..1 (.72.4 ) Gearheads At the time of shipment, a key is inserted on the gearhead s shaft. Linear Heads Brake Pack Accessories Installation CAD Data Manuals Technical Support TEL: () techsupport@orientalmotor.com C-61

44 Induction (1/7 HP, 1/2 HP) 1 W (1/ HP) 2 W (1/3 HP) Combination Type:, Hollow Shaft (Terminal Box Type) BHI62FT- RH, BHI62ET- RH, BHI62ST- RH Mass: 1. kg (22 lb.) : BHI62FT-G2, BHI62ET-G2, BHI62ST-G2 Gearhead: BH6G2- RH A31 13 ( 4.6) 16 (6.3) 14 (6.6) 16 (.63) 99 (3.9) 11 (4.6) Key (Included) 2.2 (.94.) 19.3 (4.3) 3 (1.1) 1 (.9) 1. (.6) 7.36 ( ).36 (.31.14) 3 (1.1) 1 (.9) 1. (.6) 4 W 9 W 2 (1.1) max. 2 (.9) 7 (2.9) 9 (.3) 12 (4.2) (.31 ) ϕ4 (ϕ1.7) 4 (.16) ϕ.46 (ϕ2.23.1) (.943 ) 12±. (4.72±.2) 4. (.19) Flange Mounting Surface A A Groove for Retaining Ring ϕ26.2 (ϕ1.3 ) 62 (2.) 43 (1.69) 2 W 2-Pole 4-1 W (1/19-1/ HP) Use cable with a diameter of ϕ6 ϕ12 mm (ϕ.24 ϕ.47 in.). Details of terminal box Page C-23 A A 14 (4.9) 2.3 (1.11) 14 (4.9) 4 ϕ. (ϕ.33) Thru 66 (2.6) C-62 ORIENTAL MOTOR GENERAL CATALOG 212/213 Page Features C-2 / System Configuration C-23 / Specifications C- / Product Line C- Dimensions C-6 / Connection Diagrams C-67 / and Gearhead Combinations C-69

45 Standard AC Combination Type:, Solid Shaft (Terminal Box Type) BHI62FT- RA, BHI62ET- RA, BHI62ST- RA Mass: 1. kg (22 lb.) : BHI62FT-G2, BHI62ET-G2, BHI62ST-G2 Gearhead: BH6G2- RA A32 16 (6.3) 14 (6.6) Introduction Induction 16 (.63) 99 (3.9) 11 (4.6) Reversible Electromagnetic Brake 7 (2.9) 9 (.3) 12 (4.2) 32 (1.26) 4 (.16) 4 (1.9) ϕ22.21 (ϕ.661.) 24. (.96) ϕ.46 (ϕ2.23.1) 62 (2.) Clutch & Synchronous Brake 14 (4.9) 13 ( 4.6) 2 (1.1) max. 2 (.9) M6 12 (.47) Deep 4±. (1.7±.2) ϕ12±. (4.72±.2) 43 (1.69) Low-Speed Synchronous Use cable with a diameter of ϕ6 ϕ12 mm (ϕ.24 ϕ.47 in.). Details of terminal box Page C (4.9) 4 ϕ. (ϕ.33) Thru 66 (2.6) Watertight, Dust-Resistant Key and Key Slot (Included) 32±.2 (1.26±.) 6.3 ( ) 6.3 ( ) At the time of shipment, a key is inserted on the gearhead s shaft (.72.4 ) Gearheads Linear Heads Brake Pack Accessories Installation CAD Data Manuals Technical Support TEL: () techsupport@orientalmotor.com C-63

46 Induction (1/7 HP, 1/2 HP) 1 W (1/ HP) 2 W (1/3 HP) 4 W 9 W Combination Type: Parallel Shaft (Cable Type) BHI62F-, BHI62E-, BHI62S- Mass:. kg (1 lb.) : BHI62F-G2, BHI62E-G2, BHI62S-G2 Gearhead: BH6G2- A33 13 ( 4.6) Cable ϕ7. (ϕ.31), mm (2 in.) Length UL Style 3271, AWG2 Protective Earth Terminal M4 16 (6.3) 72 (2.3) 42 (1.6) 1. (.41) 33.±. (.2) (1.32±.2) 2 (.9) 2. (.1) 32. (1.2) (2.2) 14 (.) ϕ1.1 (ϕ.77.7) ϕ2 (ϕ.79) 2 (.79) M6 12 (.47) Deep 2. (.1) ϕ42(ϕ1.6) (.2) max. Protective Earth Terminal M4 14 (4.9) 4 ϕ. (ϕ.33) Thru 12±. (4.72±.2) 27 (1.6) 14 (4.9) 2 W 2-Pole 4-1 W (1/19-1/ HP) Combination Type: Parallel Shaft (Terminal Box Type) BHI62FT-, BHI62ET-, BHI62ST- Mass:. kg (1 lb.) : BHI62FT-G2, BHI62ET-G2, BHI62ST-G2 Gearhead: BH6G2- A34 2 (1.1) max. 7 (2.9) 9 (.3) 2 (.9) 13 ( 4.6) 33.±. (1.32±.2) 2 (.9) ϕ1.1 (ϕ.77.7) ϕ2 (ϕ.79) M6 12 (.47) Deep 2 (.79) 2. (.1) ϕ42 (ϕ1.6) 12±. 62 (2.) (4.72±.2) 14 (4.9) 43 (1.69) 16 (6.3) 1. (.41) (.2) 72 (2.3) 42 (1.6) 4 ϕ. (ϕ.33) Thru 14 (4.9) Use cable with a diameter of ϕ6 ϕ12 mm (ϕ.24 ϕ.47 in.). Details of terminal box Page C-23 Key and Key Slot (Included) 2±.2 (.94±.) 6.3 ( ) 6.3 ( ) (.71.4 ) At the time of shipment, a key is inserted on the gearhead s shaft. C-64 ORIENTAL MOTOR GENERAL CATALOG 212/213 Page Features C-2 / System Configuration C-23 / Specifications C- / Product Line C- Dimensions C-6 / Connection Diagrams C-67 / and Gearhead Combinations C-69

47 Standard AC Round Shaft Type (Cable Type) BHI62F-A, BHI62E-A, BHI62S-A Mass:. kg (11 lb.) A37 13 ( 4.6) 16 (6.3) 1. (.41) 32. Cable ϕ7., (ϕ.31), mm (2 in.) Length (1.2) UL Style 3271, AWG2 (2.2) 37 (1.46) 2 (.) 14 (.) 3 (1.1) 13 (.1) ϕ14.1 (ϕ.12.7) ϕ94.3 (ϕ3.7.14) 14 (4.9) (.2) max. Protective Earth Terminal M4 4 ϕ. (ϕ.33) Thru 27 (1.6) 12±. (4.72±.2) Introduction Induction Reversible Electromagnetic Brake Protective Earth Terminal M4 2. (.1) Round Shaft Type (Terminal Box Type) BHI62FT-A, BHI62ET-A, BHI62ST-A Mass:. kg (11 lb.) A3 2 (1.1) max. 2 (.9) 7 (2.9) 9 (.3) 43 (1.69) ϕ14.1 (ϕ.12.7) 62 (2.) Clutch & Synchronous Brake Low-Speed Synchronous Watertight, Dust-Resistant 13 ( 4.6) 3 (1.1) 13 (.1) ϕ94.3 (ϕ3.7.14) 14 ( 4.9) 12±. (4.72±.2) Gearheads Use cable with a diameter of ϕ6 ϕ12 mm (ϕ.24 ϕ.47 in.). Details of terminal box Page C (.41) 16 (6.3) 2 (.) 37 (1.46) 4 ϕ. (ϕ.33) Thru Linear Heads Brake Pack Accessories Installation CAD Data Manuals Technical Support TEL: () techsupport@orientalmotor.com C-6

48 Induction (1/7 HP, 1/2 HP) 1 W (1/ HP) 2 W (1/3 HP) (Included with single-phase motors) ϕ4.3 (ϕ.169) AMP#17 A 2 (.79) C B 7 (.2) 1 (.39) 4 (.16) B+1 (.9) R1 (R.39) 6 (.24) Dimensions Unit = mm (in.) A B C Cable Type Terminal Box Type BHI62F- RH BHI62F- RA BHI62F- BHI62F-A BHI62E- RH BHI62E- RA BHI62E- BHI62E-A BHI62FT- RH BHI62FT- RA BHI62FT- BHI62FT-A BHI62ET- RH BHI62ET- RA BHI62ET- BHI62ET-A CH4CFAUL2 CH1BFAUL (2.2) (2.2) 41 (1.61) 3 (1.3) (2.2) (1.97) Mass g (oz.) 17 (6.2) 132 (4.7) Cap Included 4 W Mounting Method for, Hollow Shaft Types Page C W 2 W 2-Pole 4-1 W (1/19-1/ HP) C-66 ORIENTAL MOTOR GENERAL CATALOG 212/213 Page Features C-2 / System Configuration C-23 / Specifications C- / Product Line C- Dimensions C-6 / Connection Diagrams C-67 / and Gearhead Combinations C-69

49 Standard AC Connection Diagrams The direction of motor rotation is as viewed from the shaft end of the motor. CW represents the clockwise direction, while CCW represents the counterclockwise direction. Enter the voltage (F, E) in the box ( ) within the model name. Single-Phase Induction Three-Phase Induction Type Cable Type Terminal Box Type Cable Type Terminal Box Type Clockwise BHI BHI62-1 CW Clockwise BHI62 T-3 9 BHI62 T- 1 CW Clockwise BHI62S-3 9 BHI62S- 1 CW Clockwise BHI62ST-3 9 BHI62ST- 1 CW Introduction Induction Reversible L N White Red Black L N Z2 U2 U1 L1 (R) L2 (S) L3 (T) Red White Black L1(R) L2(S) L3(T) U V W Electromagnetic Brake Combination Type: Parallel Shaft Counterclockwise CCW L N Clockwise L N White Red Black Counterclockwise L N Z2 U2 U1 CCW Counterclockwise To change the rotation direction, change any two connections between L1(R), L2(S) and L3(T). Counterclockwise To change the rotation direction, change any two connections between L1(R), L2(S) and L3(T). BHI BHI62 T BHI62S BHI62ST White Red Black CW Clockwise L N Z2 U2 U1 CW Clockwise L1 (S) L2 (R) L3 (T) Red White Black CW Clockwise L1(S) L2(R) L3(T) U V W CW Clutch & Synchronous Brake Low-Speed Synchronous Watertight, Dust-Resistant CounterclockwiseCCW L N : Protective Earth Connecting to the terminal Applicable lead wires: AWG24 12 Strip length: mm (.31 in.) White Red Black Counterclockwise L N Z2 U2 U1 CCW Counterclockwise To change the rotation direction, change any two connections between L1(S), L2(R) and L3(T). Counterclockwise To change the rotation direction, change any two connections between L1(S), L2(R) and L3(T). Note Change the direction of single-phase motor rotation only after bringing the motor to a stop. If an attempt is made to change the direction of rotation while the motor is rotating, motor may ignore reversing command or change its direction of rotation after some delay. How to connect a capacitor Page C-22 Gearheads Linear Heads Brake Pack Accessories Installation CAD Data Manuals Technical Support TEL: () techsupport@orientalmotor.com C-67

50 Induction (1/7 HP, 1/2 HP) Type Single-Phase Induction Three-Phase Induction Cable Type Terminal Box Type Cable Type Terminal Box Type BHI62 -RH 1RH BHI62 -RA 1RA BHI62 T-RH 1RH BHI62 T-RA 1RA BHI62S-RH 1RH BHI62S-RA 1RA BHI62ST-RH 1RH BHI62ST-RA 1RA Clockwise CW Clockwise CW Clockwise CW Clockwise CW 1 W (1/ HP) 2 W (1/3 HP) 4 W 9 W 2 W 2-Pole 4-1 W (1/19-1/ HP) Combination Type: Right Angle Shaft Round Shaft Type L N Counterclockwise L N Clockwise L N Counterclockwise L N White Red Black White Red Black CCW L N Counterclockwise L N Z2 U2 U1 Z2 U2 U1 CCW L1 (S) L2 (R) L3 (T) Red White Black Counterclockwise To change the rotation direction, change any two connections between L1(S), L2(R) and L3(T). L1(S) L2(R) L3(T) U V W Counterclockwise To change the rotation direction, change any two connections between L1(S), L2(R) and L3(T). BHI62 -A BHI62 T-A BHI62S-A BHI62ST-A White Red Black White Red Black CCW CW Clockwise L N Counterclockwise L N Z2 U2 U1 Z2 U2 U1 CCW CW Clockwise L1 (R) L2 (S) L3 (T) Counterclockwise Red White Black CW To change the rotation direction, change any two connections between L1(R), L2(S) and L3(T). Clockwise L1(R) L2(S) L3(T) U V W CW Counterclockwise To change the rotation direction, change any two connections between L1(R), L2(S) and L3(T). : Protective Earth Connecting to the terminal Applicable lead wires: AWG24 12 Strip length: mm (.31 in.) Note Change the direction of single-phase motor rotation only after bringing the motor to a stop. If an attempt is made to change the direction of rotation while the motor is rotating, motor may ignore reversing command or change its direction of rotation after some delay. How to connect a capacitor Page C-22 C-6 ORIENTAL MOTOR GENERAL CATALOG 212/213 Page Features C-2 / System Configuration C-23 / Specifications C- / Product Line C- Dimensions C-6 / Connection Diagrams C-67 / and Gearhead Combinations C-69

51 Standard AC List of and Gearhead Combinations and gearhead combinations are shown below. Combination Type: Right Angle Shaft Gearhead BHI62F- RH BH6G2- RH BHI62F-G2 BHI62F- RA BH6G2- RA BHI62FT- RH BH6G2- RH BHI62FT-G2 BHI62FT- RA BH6G2- RA BHI62E- RH BH6G2- RH BHI62E-G2 BHI62E- RA BH6G2- RA BHI62ET- RH BH6G2- RH BHI62ET-G2 BHI62ET- RA BH6G2- RA BHI62S- RH BH6G2- RH BHI62S-G2 BHI62S- RA BH6G2- RA BHI62ST- RH BH6G2- RH BHI62ST-G2 BHI62ST- RA BH6G2- RA Accessories and Peripheral Equipment Speed Control Speed Controller Page D-17 Accessories Page C-263 Combination Type: Parallel Shaft Gearhead BHI62F- BHI62F-G2 BHI62FT- BHI62FT-G2 BHI62E- BHI62E-G2 BHI62ET- BHI62ET-G2 BH6G2- BHI62S- BHI62S-G2 BHI62ST- BHI62ST-G2 Introduction Induction Reversible Electromagnetic Brake Clutch & Synchronous Brake Low-Speed Synchronous Watertight, Dust-Resistant Gearheads Linear Heads Brake Pack Accessories Installation CAD Data Manuals Technical Support TEL: () C-69

52 Induction (1/7 HP, 1/2 HP) Induction 2-Pole, High-Speed Type 4 W,, 9 W, 1 W (1/ HP) Frame Size: mm ( 3.1 in.), 9 mm ( 3.4 in.) 1 W (1/ HP) 2 W (1/3 HP) 4 W Specifications Continuous Rating Output Power Voltage Frequency Current Starting Rated Rated Speed 9 W 2 W 2-Pole 4-1 W (1/19-1/ HP) Round Shaft Type W HP VAC Hz A mn m oz-in mn m oz-in r/min μf Single-Phase IK4A-BW2U 4 1/ Single-Phase /2 Single-Phase IK4A-DW3E /19 Single-Phase Single-Phase IK6A-BW2U 6 1/ Single-Phase /14 Single-Phase IK6A-DW3E /12 Single-Phase Single-Phase IK6A-BW2U 6 1/ Single-Phase Single-Phase IK6A-DW3E 6 1/ Single-Phase Three-Phase IK6A-TW2 6 1/12 Three-Phase Three-Phase Single-Phase IK9A-BW2U 9 1/ Single-Phase Single-Phase IK9A-DW3E 9 1/ Single-Phase Three-Phase IK9A-TW2 9 1/ Three-Phase Three-Phase Single-Phase IK1A-BW2U 1 1/ Single-Phase / Single-Phase IK1A-DW3E / Single-Phase Three-Phase 2 IK1A-TW / IK1A-TW2T Three-Phase Three-Phase The U and E at the end of the model name indicate that the unit includes a capacitor. These letters are not listed on the motor nameplate. When the motor is approved under various safety standards, the model name on the nameplate is the approved model name. Page H-11 Details of safety standards Page H-2 : Contains a built-in thermal protector (automatic return type). If a motor overheats for any reason, the thermal protector is activated and the motor is stopped. When the motor temperature drops, the thermal protector closes and the motor restarts. Be sure to turn the motor power off before inspecting. C-7 ORIENTAL MOTOR GENERAL CATALOG 212/213 Page Features C-2 / System Configuration C-23 / Specifications C-7 / Product Line C-71 Dimensions C-71 / Connection Diagrams C-74