TYLDEN HERITAGE GENERAL MAIL ORDER PARTS CATALOGUE

Transcription

1 Catalogue Part No 420 TYLDEN HERITAGE GENERAL MAIL ORDER PARTS CATALOGUE Custom Classic Truck & Tractor Restorations Business Hours: Location: 1906 Trentham Road, Kyneton Vic 3444 Australia Note: Our workshop & warehouse are only open by appointment Postal Address: P.O. Box 614, Kyneton Vic 3444 Australia Supplier of after market Mack reproduction and dress up parts Big range of Mack B & R Model bits. Special Interest in: Mack Trucks...Diamond T Trucks...Caterpillar Tractors Trading since tyldenheritage@bigpond.com web: Lee No 3 Pty Ltd A.C.N A.B.N These pages may only be reproduced after obtaining written permission from Tylden Heritage All rights reserved. COST PER PRINTED CATALOGUE INCL. POSTAGE - $30

2

3 SECTION 6 - GENERAL INDEX 6A 6B 6C 6D 6E 6F 6G 6H 6I 6J AXLE, CHASSIS BRAKES CATCHES, LATCHES, HANDLES, CLIPS, FASTENERS, SPECIAL SCREWS. DRESS UP PARTS ELECTRICAL PARTS BOOKS RUBBER PARTS & MOULDINGS REPRODUCTION CAST PARTS STEEL INSTRUCTION PLATES STICKERS. SEE GENERAL SECTION CATALOGUE FOR OTHER PART OPTIONS - Parts for Axle, Brakes, Catches, Dress Up, Electrical, Parts Books, Rubber Parts, Reproduction Cast Parts, Steel Name Plates & Instruction Plates & Stickers.

4 8/09/16 SECTION 6A - AXLE/ CHASSIS ALL PRICES ARE SUBJECT TO GST AIR BAG (AIR SPRING) CONVERSION KIT FOR PASSENGER COMFORT AND DRIVER FATIGUE, AS THE DRIVER HAS A VEHICLE WITH IMPROVED HANDLING, BETTER STEERING, GREATER BRAKING ABILITY Tylden Heritage now offers load sharing air helper suspension suitable for insulation on front suspensions for truck chassis and highway vehicles. Note: Load sharing is intended for use on primary front suspensions with 3.5 or 4 inch wide springs. The base casting must be slightly modified for use on the 3.5 inch springs, each kit includes 2 air bags, upper and lower mounting K4 brackets, cab mounted pressure regulator/gauge panel and air fittings and pipe. Cost is dependant on truck model, size & type of kit required. PHOTO SHOWS R MACK. AIR REGULATOR 2274 Air regulator 1/4 inch fitting mounting bracket with 40mm gauge 0-150PSI KPA Cost from $ $30.00 AIR SPRING 2273 Firestone Air spring base 7" (180mm) height unloaded, 9 inch (225mm) top width 61/4 inch (160mm) $ SPIDER HUB TO MODERN 10 STUD HUB CONVERSION KIT MACK 44000lb DIFF rear axle 10 stud USA hubs. 6 stud axle hubs drive Mack. Part No MK3398HR735K. Price per each. NEW. Limited Stock. $ Brake drum for above conversion. Price per each. NEW $ AXLE, STUDS & NUTS (suit modern hubs) 2121 Late type hub pilot axle studs 22mm diam 1.5 thread. Note: length and shank size can vary with different types of hubs and wheels. - PER EACH $ Late type hub pilot axle nuts. PER EACH. Bin 2121 $ 5.00 EARLY STUD PILOT (IMPORTED EARLY USA TRUCKS) 2124 Early type stud pilot inner sleeves. Note: Left & right threads. Have 2" of thread on sleeve. PER EACH $ Early type stud pilot outer nuts. Note: Left & right threads. PER EACH. $ 4.25 SECTION 6A - GENERAL - AXLE 1

5 8/09/16 SECTION 6A - AXLE./CHASSIS ALL PRICES ARE SUBJECT TO GST 2126 Early type stud pilot inner sleeves. Note: Left & Right threads 30mm (1 1/2 of thread). Suit steel wheels. PER EACH $ Nut for above PER EACH $ 4.00 SPIDER WHEEL NUTS 2128 Standard Spider wheel rear wheel nut - 3/4 thread in ID 1.25 inch OD. $ 1.15 THE HISTORY ON TYPES OF USA STUD WHEELS There are two types of wheels - "Stud" pilot which use the nuts to centre the wheels, not common in Australia but on some imported vintage trucks. Today most are "Hub" pilot which uses the hub to centre the wheels. 150 pattern on the same old style Bud wheels. Some have a large stud and a thin nut and some have small stud and a large nut. Early aluminium wheels had 5 slots. The story goes P.I.E. (Pacific Intermountain Express) had Alcoa make these wheels in the fifties as weight saving when tubeless was unheard of. The first Alcoa tubeless wheels started 1956 with a new design in 1963 and changed from 5 holes to 10. Tyres lasted better, less flats, easier repairs. HISTORY OF SPIDER TUBELESS STEEL RIMS With the change from inch tube tyres they became 22.5 and inch became 24.5 in tubeless and the 24 inch tube tyre do not have a tubeless replacement. Tubeless rims first started to go on the Australian market in early 1970's. There are 3 standard sizes,7.5 inches wide x 22.5 inches diameter inches wide x 22.5 inches diameter. This is the best size for the 11R.22-5 tyre. The third is the offset type rim 9 inches wide x 22.5inches diameter. This rim is suitable for chroming for use on the steer axle. I purchased the first new truck with tubeless rims in 1976 and went from 4 to 6 punctures per week to zero road side changes per year. FUEL, OIL, AIR TYPE TANK J BRACKETS inch - J Bracket radius POA inch - J Bracket radius POA inch - J Bracket radius POA inch - J Bracket radius POA inch - J Bracket radius POA Prices vary with size. Small start at $95 each to large heavy duty $250 each. NOTE: Mounting holes differ on some model trucks and holes may need to be changed. Tank strap in stainless steel $40 - $110 each. Mounting rubber $12 to $20 each. SECTION 6A - GENERAL - AXLE 2

6 8/09/16 SECTION 6A - AXLE./CHASSIS ALL PRICES ARE SUBJECT TO GST ALL PRICING SUBJECT TO GST FUEL TANK CAPS - LARGE 262 Brass fuel cap large type with four lugs - Snyder Buffalo cast from brass & machined with new 100mm thread 130mm Top - new $ FUEL TANK CAPS - SMALL 273 Brass fuel cap 55mm thread (2 1/8). Top 70mm (2 5/8) Snyder - Used $ FUEL TANK FILLER 363 Fuel tank filler tube aluminium for welding into tanks to take large B (part 262) filler caps. Note: not machined - new. POA 363a With clean up and new thread for Buffalo cap 262 ready for welding into tank POA FUEL TANK TAP 1395 Brass stop tap - new - 1/2 female, 1/2 male, NPT thread with round gate wheel handle - looks like original - new. PRICE PER EACH. Bin $ TRUCK TANK VALVE 1396 Brass stop tap 3/8 NPT female. 3/8 NPT Male. $ TRUCK TANK VALVE FLARE OUTLET 1397 Brass stop tap 1/2 flare x 1/2 NPT $ SECTION 6A - GENERAL - AXLE 3

7 SECTION 6B - BRAKES - ALL PRICES ARE SUBJECT TO GST AIR BRAKE GLADHAND TRAILER BRAKE COUPLING 633 B Model original glad coupling bracket only. Bolts onto rear of B Model cabin. Fitted to many B Models with T in chassis number. - Used $ a As above - available chrome plated NA BRAKE COUPLINGS 607 Trailer brake coupling self sealing 1/2 NPT female thread connection. $ Trailer brake coupling self sealing 1/2 NTP male thread connection. Bin 621 $ Trailer brake coupling non sealing adaptor 1/2 NPT female thread $ Trailer brake coupling, 1/2 NPT male thread $ Trailer brake coupling 3/8 NTP. Male thread. $ 6.00 BRAKE STOP SWITCH 591 Air system brake stop light switch. 1/4 gas thread. $ BRAKE LOW PRESSURE SWITCH 592 Air system low pressure switch 1/8 gas thread. Bin 591 $ BRAKE DIAPHRAM 643 Type 12 OR 16 Replaceable diaphram. Suit B Model - FRONT $ 8.00 SPRING BRAKE TYPE 24/ Bolt direct onto B Model backing plate lugs 24/24 Price per each. $ Spring brake assembley 30/30. Note: will only fit B Mack with adaptor plate. POA 6B-GENERAL - BRAKES 4

8 SECTION 6B - BRAKES - ALL PRICES ARE SUBJECT TO GST POGO STICK 605 Pogo stick chrome $ SUZI COIL 609 Dual brake suzi coil - short tail. $ Suzi coil 7 core - long tail 3.6m $ Pogo stick Suzie coil clamp hinges to allow placement of hoses and cable and held in place by steel clasp. $ TREDDLE OR FOOT VALVE - LATE TYPE 579 Brake - treddle or foot valve (only). Suit B Model conversion adaptor. See B Mack cab interior for detail - New. Can be used on single or dual line brake systems on most USA trucks. $ Pedal assembly suit above foot valve (579). Note: Can only be purchased with late type pedal (as photo). The curved original B pedal will fit into this new bracket or for R Model we offer a pedal with Mack logo (Part no 3074 below). Suit E3 & E6 foot valve $ R MODEL FOOT VALVE PEDAL 3074 New brake pedal with Mack logo. Note: holes are not drilled. $ AIR TANK DRAIN VALVES 1403 Drain cock 3/8 thread with 4ft (1220mm) long cable. NEW $ DRAIN COCK VALVE /4 BSP with standard quick T bar control $ /8 BSP with hex nut tamper proof control $ 9.25 AIR PRESSURE RELIEF VALVE /4 BSP. The 106SV Series valve. Comes set a 11 bar/160 PSI with a plastic tamper proof cap for protection. Please contact us for available pressure ranges. $ B-GENERAL - BRAKES 5

9 SECTION 6B - BRAKES - ALL PRICES ARE SUBJECT TO GST TRACTOR PROTECTION VALVE 625 Trailer Tractor Protection Valve $ BRAKE RELAY VALVE 626 Brake relay valve service brakes. Suit tandem or single axle. $ BRAKE RELEASE VALVE 627 Brake relay valve for spring brake $ DUMP VALVE 611 Dump valve for brakes - 3 port 3/8 NPT, used on B Models and other early type trucks, not used today as they are noisy. $ GOVENOR VALVE 610 Govenor valve (air compressor control valve). Bin 589 $ AIR TANK NON RETURN VALVE 612 In line non return valve with 1/2 NPTF ports. Bin 620 $ DOUBLE CHECK VALVE 622 Double check valve 3/8 NPTF ports. Bin 620 $ PRESSURE CONTROL VALVE 620 The valve is used to assure a nominal pressure level of 70 PSI. In the event of a system failure or a decrease in the valves supply pressure, the valve will prevent futher pressure loss or reverse flow. 1/4-18 NPTF ports 60mm long $ BRAKE CONTROL VALVES TRACTOR PROTECTION VALVE 586 Valve dash control. Note: Knob part 590 & 588 and holding nut 587 is extra. (see over for options.) $ B-GENERAL - BRAKES 6

10 SECTION 6B - BRAKES - ALL PRICES ARE SUBJECT TO GST SPRING BRAKE CONTROL 590 Knob only tractor protection. Suit 586. Bin 586 $ BRAKE CONTROL KNOB 618 Black reserve knob 38mm diam top. Suit 586 KNOBS AVAILABLE FOR VALVE 586 ROUND ALL BLACK WITH WHITE WRITING. PARKING BRAKE. EMERGENCY BRAKE, AUXILIARY BRAKE. RESERVE AIR. SYSTEM EMERGENCY CONTROL, WITH DIAMOND SHAPE WITH YELLOW DOT PARKING BRAKE (PULL TO APPLY, PUSH TO RELEASE. 587 Nut to hold tractor protection valve. Suit part 586 Bin 586 $ Locking pin for valve knob. Suit part 590. Bin 586 $ 3.50 SPRING BRAKE OPTION VALVES 584 Spring brake dash control valve lever type with slide lock - RED $ Spring brake dash control valve -pull type $ EARLY TYPE AIR ON/OFF UNIVERSAL VALVE 583 Air simple slide control valve. Suit most early trucks. See following usage description plates. Can be supplied with other truck make logos. Bin 604 $ B-GENERAL - BRAKES 7

11 SECTION 6B - BRAKES - ALL PRICES ARE SUBJECT TO GST DESCRIPTION PLATES SUIT VALVE PART NO 583 TRUCK VALVE ID CONTROL 1247 Truck Tractor Brake control lever plate with Mack logo normal emergency - cut out and made lever slot. Bin 1242 $ POWER DIVIDER ID CONTROL PLATE 1249 Power divider Dry or Slippery Road ID control plate with steel backing and logo. Bin 1248 $ POWER DIVIDER 1252 Power divider IN/OUT ID plate with steel backing and logo - option Bin 1252 $ AIR SUSPENSION 1217 Air suspension normal or deflate ID ple\ate with steel backing and logo $ TRAILER AIR SUPPLY 1218 Trailer Air Supply ON/OFF $ OPTIONS WE CAN ALSO OFFER VALUE DESCRIPTION PLATES FOR YOUR CUSTOM TRUCK WITH A MAKER OF YOUR CHOICE. SPRING BRAKE ID PLATE 1251 Spring brake ID plate. Up Down Lever. Type with lock. Bin 1248 $ ENGINE BRAKE PLATE 1250 Engine Brake ID Plate. $ B-GENERAL - BRAKES 8

12 SECTION 6B - BRAKES - ALL PRICES ARE SUBJECT TO GST STANDARD BRASS BSP SCREWED FITTINGS (CATEGORY 1) HEX PLUG 1993 Brass hexagon head plug - 1/8 NPT. Bin 644A $ Brass Hexagon head plug - 1/4 NPT. Bin 644A $ Brass hexagon head plug - 3/8 NPT. Bin 644A $ Brass Hexagon head plug - 1/2 NPT. Bin 644A $ Brass Hexagon head plug - 3/4 NPT. Bin 644A REDUCING BUSHES 2000 Brass reducing bush - 1/8 to 1/4 NPT. Bin 644B $ Brass reducing bush - 1/8 to 3/8 NPT Bin 64B $ Brass reducing bush - 1/4 to 3/8 NPT Bin 644B $ Brass reducing bush - 1/4 to 1/2 NPT. Bin 644B 2004 Brass reducing bush - 1/2 to 1/8. Bin 644B 2005 Brass reducing bush - 1/2 to 1/4. Bin 644B ELBOW M & F COMPACT 2006 Elbow M & F 1/8 Bin 645 $ Elbow M&F 1/4 Bin 646 $ Elbow M&F 3/8.Bin 647 $ Elbow M&F 1/2. Bin 648 $ 9.00 ELBOW 45 DEGREES M & F Elbow 45 deg. M&F 1/8. Bin 645B $ Elbow 45 deg. M&F 1/4 Bin 645C $ Elbow 45 deg. M&F 3/8. Bin 645D $ Elbow 45 deg. M&F 1/2 Bin 645E $ HEX SOCKET 2016 Brass Hexagon socket - 1/8 NPT Bin 646A $ Brass Hexagon socket - 1/4 NPT. Bin 646B $ Brass Hexagon socket - 3/8 NPT Bin 646C $ Brass Hexagon socket - 1/2 NPT Bin 646D $ Brass Hexagon socket - 3/4 NPT Bin 646E $ B-GENERAL - BRAKES 9

13 SECTION 6B - BRAKES - ALL PRICES ARE SUBJECT TO GST STANDARD BRASS BSP SCREWED FITTINGS (CATEGORY 1) HEX NIPPLE /8 Bin 646A $ /4 Bin 646A $ /8 Bin 646A $ /2 Bin 646A $ 4.00 LONG HEX NIPPLE /8 X 2 Bin 646B $ /4 x 2 Bin 646B $ /8 x 2 Bin 646B $ /8 to 1 1/2 Bin 646E /4 to 4.0 Bin 646E M & F LONG ADAPTOR REDUCING NIPPLE /4 x 1/8 Bin 646G $ /8 x 1/8 Bin 646G $ /8 x 1/4 Bin 646G $ /2 x 1/8 Bin 646G $ /2 x 1/4 Bin 646G $ /2 x 3/8 Bin 646G $ 6.00 REDUCING SOCKET /2 X 1/8 Bin 646C $ /2 x 1/4 Bin 646C $ /2 x 3/8 Bin 646C $ /4 x 1/8 Bin 646C $ /8 x 1/2 Bin 646C $ /8 x 1/4 Bin 646C $ 7.00 FEMALE TEE /8 Bin 646D $ /4 Bin 646D $ /8 Bin 646D $ /2 Bin 646D $ MALE BRANCH TEE /8 $ /4 $ /8 $ /2 $ FEMALE CROSS /8 $ /4 $ /8 $ /2 $ HEX LOCK NUT 2061 Lock nut - 1/8 $ Lock nut - 1/4 $ Lock nut - 3/8 $ Lock nut - 1/2 $ Lock nut - 3/4 $ B-GENERAL - BRAKES 10

14 SECTION 6B -BRAKES - ALL PRICES ARE SUBJECT TO GST BRASS BULKHEAD FITTINGS - SUITABLE FOR FITTING BRAKE LINES THROUGH CHASSIS & FIREWALL 631 Bulkhead or chassis fitting 1/2" male x 1/2" female - 2 inches long. Bin 629 $ FEMALE BULK HEAD FITTING 2073 Bulk Head - 1/8 - M16 x 1.5 $ Bulk Head - 1/4 - M20 x 1.5 $ Bulk Head - 3/8 - M26 x 1.5 $ Bulk Head - 1/2 - M28 x 1.5 $ MANIFOLD ROUND /4 to 1/4 $ MANIFOLD STANDARD /8 to 1/4 $ B-GENERAL - BRAKES 11

15 SECTION 6B -BRAKES - ALL PRICES ARE SUBJECT TO GST BRASS SLEEVE 1400 SERIES COMPRESSION 564 Brass Sleeve - 1/4 Bin Brass Sleeve - 3/8 Bin 564 $ Brass Sleeve - 1/2 Bin Brass Sleeve - 5/8 Bin 564 $ 2.30 BRASS INSERT SERIES 571 Brass insert - 1/4 Bin Brass insert - 3/8 Bin Brass insert - 1/2 Bin Brass insert - 5/8 Bun 571 BRASS NUT 1400 SERIES 555 Brass nut - 5/8 Bin Brass nut - 3/8 Bin Brass nut - 1/2 Bin Brass nut - 5/8 Bin 555 MALE CONNECTORS 524 Brass SAE 45 flare male connector 1/2 tube 3/4 SAE 1/4 NPT. Bin Brass SAE 45 flare male connector - 3/8 tube 5/8 SAE 3/8 NPT Bin Brass SAE 45 flare male connector - 3/8 tube 5/8 SAE 1/4 NPT Bin Brass SAE 45 flare male connector - 1/2 tube 3/8 NPT Bin 524 NYLON TUBE JOINERS 500 1/4 Nylon Tube Joiner $ /8 Nylon Tube Joiner $ /2 Nylon Tube Joiner $ MALE CONNECTORS 542 Brass male connector tube - 3/8 x 1/4 NPT Bin 542 $ Brass male connector - 3/8 x 3/8 NPT Bin 542 $ Brass male connector 1/2 tube x 1/2 NPT Bin 542 $ 7.00 MALE BRANCH TEE 569 Brass male branch tee - 3/8 x 3/8 tube x 1/4 NPT. Bin 569 ELBOW FLARE - 90 Deg 526 Brass 90 deg - SAE 45m Flare 1/2 tube 1/4 NPT. Bin 526 $ Brass 90 deg SAE 45 flare elbow 1/2 tube 3/8NPT.. Bin 526 $ Brass 90 deg SAE 45 flare 1/2 tube 1/2 NPT $ 8.00 ELBOW 90 Deg CONNECTOR 545 Brass elbow 90- deg 3/8 tube 3/8 NPT. Bin Brass elbox 90 deg 3/8 tube 1/4 NPT. Bin 542 ELBOW 45 Deg CONNECTOR 544 Brass elbow 45 deg - 3/8 tube 1/4 NPT. Bin 542 6B-GENERAL - BRAKES 12

16 SECTION 6B -BRAKES - ALL PRICES ARE SUBJECT TO GST FIELD ATTACHABLE 247 N SERIES 539 Steel NPT male rigid hose fitting - 5/16 ID x 1/4 pipe 540 Steel NPT male rigid hose fitting - 5/16 hose ID 3/8 pipe JIG FEMALE SWIVEL 547 Steel female 45 flare 3/16 hose Steel female 45 flar 1/4 hose Steel female 45 flare 5/16 hose Steel female 45 flare 7/8 hose 6B-GENERAL - BRAKES 13

17 SECTION 6B -BRAKES - ALL PRICES ARE SUBJECT TO GST BRAIDED BRAKE HOSE GIVE YOUR RESTORATION THAT PERIOD LOOK WITH COTTON BRAIDED FABRIC COVERED LOW PRESSURE HOSE. APPLIATION AIR, FUEL. OIL & WATER, WORK PRESSURE 350 PSI. TEMP RANGE 40OC TO 100OC. Sold per metre 613 Cotton braided air hose - 3/ Cotton braided air hose - 5/ Cotton braided air hose - 1/4 617 Cotton braided air hose - 1/2 618 Cotton braided air hose - 7/8 6B-GENERAL - BRAKES 14

18 SECTION 6C - CATCHES, LATCHES, HANDLES, CLIPS, FASTENERS, SPECIAL SCREWS ALL PRICING SUBJECT TO GST UNIVERSAL QUARTER VENT HANDLE 712 Vent or quarter vent universal turn catch and locating plate. Bin 714. Price Per Each. $ AFTER MARKET LOOK A LIKE STAR WHEEL HOOD PROPS - SUITABLE FOR BONNETS, TOOL BOXES & BINS etc 726 Bonnet hood star wheel prop 152mm closed, extended 239mm - NEW - Price per each 727 Bonnet hood star wheel prop 285mm closed 470mm, open - NEW - Price per each 728 Bonnet Hood star wheel prop or support stay - 290mm closed - 495mm open with 2 brackets - NEW - Price per each CATCHES & LATCHES BATTERY BOX OR BONNET LATCHES 723 B & R model chrome battery box latch, also fits Toyota 40 & 45 series and many other early type bonnets. Foot can be moved to suit base angle. $ DOOR T LOCK CATCH 715 Door T lock with stainless steel spring loaded dust cover. Rubber seal under stainless steel cup, multiple rod mounts on locking tongue, stainless steel shaft keyed alike - used mainly on tool boxes $ FLUSH PADDLE LOCK 716 Flush paddle type lock with keys. Suits one or two rods or cables. $ Flush Paddle locks with keys - S/S - gasket suit stricker plate - see stricker plate for catches - used mainly on tool boxes. $ COMPRESSION LOCK 713 Compression lock satan finish & key with adjustable close position to suit thickness of box 70mmx32mm hole. tank boxes. $ OPEN/CLOSE PUSH LOCK 730 Glove box and small panel button push lock. 5/8 thread.. Bin 773 KEY DOOR LOCKS 856 Door & ignition lock set includes 2 door tumblers and one ignition tumbler with 2 matching keys. B88, See General 6E-2 for pricing. $ SECTION 6C - GENERAL CATCHES & LATCHES - 15

19 SECTION 6C - CATCHES, LATCHES, HANDLES, CLIPS, FASTENERS, SPECIAL SCREWS ALL PRICING SUBJECT TO GST DECK LOCKS 718 Quarter turn latches - vibration resistant die cast - suit mounting in deck plate up to 8mm - holds down deck drill 20mm hole. 2 types of latch available. $ COVER FOR Moulding deck latch lift up lid, chrome plated 28.5mm wide screw centres 20.6mm. Designed to cover 718 but will need drilling & tapping $ Key to open Quarter turn locks 718 $ 5.45 UNIVERSAL DOOR HANDLE 1111 Traditional arched chrome all purpose universal door handle with key suit outside door opening - early type trucks and cars - 130mm long, 56mm high with 125mm long, 8mm shaft. $ SECTION 6C - GENERAL CATCHES & LATCHES - 16

20 SECTION 6C - CATCHES, LATCHES, HANDLES, CLIPS, FASTENERS, SPECIAL SCREWS INTER COOLER TYPE CLAMP 1866 Spring loaded inter cooler stainless steel clamp - 5 inch $ Spring loaded inter cooler stainless steel clamp - 6 inch $ POSITIVE STAINLESS STEEL WATER HOSE CLAMPS 1869 Super Clamp $ Super Clamp /2 inch $ Super Clamp inch $ Super Clamp inch $ Super Clamp inch $ SECTION 6C - GENERAL CATCHES & LATCHES - 17

21 SECTION 6C - CATCHES, LATCHES, HANDLES, CLIPS, FASTENERS, SPECIAL SCREWS HINGES - CONTINUOUS PIANO HINGE - SUITABLE FOR BONNETS & LIGHT TOOLBOXES Piano hinge type- stainless steel - to suit new made up bonnets, tool boxes etc x38mm S/S cost per each. $ TYLDEN TYPE HINGE CHANNEL 135 Tylden type hinge Channel to suit new made up bonnets x20x20x20mm - Used with two optional Piano Hinge $ BACK FLAP HINGE 1125 Back flap steel hinge with off set pin - suit early truck cabin, also suit heavy applications - width 50mm length 80mm, flap thickness 6mm - Pin size 8mm $ DOOR STRICKER PLATE Step stricker plate - 56mm (2 1/4 inches) L x 25mm (1 inch) 10mm high 2 mounting holes on each side. Suit flush paddle locks and some early car and trucks $ Step stricker plate - 238mm (1 1/2inches) 30mm L - mounting holes on each side $ 6.35 DOVE TAILS 2267 Door guide Vee catch to locate door 62mm long 28mm wide, with 4 holes - suit Mack L cabins but many other early model trucks and cars - cast from brass. Note: Not drilled as holes vary with different models - Sold per each $ DOOR LOCKS 1976 Roto-lok it star wheel replacement. Suit Mack trucks , also Chrysler dodge, DeSoto, Plymouth , Studebaker 37 & 48, Nash 40 48, Packard Suit front right or rear left door. See Cast Parts for more detail. LONG ENTRY GRAB HANDLES 1120 Chrome plated brass grab handle 308 long x 25 with 50mm clearance. 3 mounting holes. Note These are available up to 1200mm long. Suitable cab & sleeper entry or rear of cabin. $ OUTSIDE CAB GRAB ENTRY HANDLE 1119 Stainless steel cabin grab handle - cast not exactly original B Model type but good look a like, same bolt pattern - length 7 inch (17.77mm) bolt centres. 1 1/2 inch (15mm) x 210mm. - sold per each $ SECTION 6C - GENERAL CATCHES & LATCHES - 18

22 SECTION 6C - CATCHES, LATCHES, HANDLES, CLIPS, FASTENERS, SPECIAL SCREWS ALL PRICING SUBJECT TO GST SPECIAL STAINLESS STEEL BOLTS BUMPER BAR CUB HEAD OR TIMBER BOLTS 2909 Bumper bar type 26mm Domed head 8mm square shank 65mm long 5/16 UNC.. Bin 2909 $ Bumper bar type domed head stainless steel. 30mm x 10mm. Bin $ 5.00 CAGED NUTS WITH WELD ON TAGS ALSO REFERRED TO AS FLOATING THE DESIGN. ALLOWS THE NUT TO FLOAT WITHIN THE STEEL CAGE FOR HOLE MISALIGNMNT Caged Nuts - 6mm 1/14-20 $ Caged Nuts - 8mm. 5/ Bin 2903 $ Caged Nuts - 10mm. 3/8-16. Special Order Only CHEESE HEAD 2936 Raised cheese slotted head 1/4 UNC 1 3/4 long stainless steel screws. PER EACH. Bin 2917 $ Cast radiator top tank holding S/S screws for (Suit B615, B ) 1 1/2 x 3/8. Suit most models with cast radiator. 4 required. Price per Each..NEW..Bin 2917 $ 6.00 OLD TIME DOMED HEAD COUNTER SUNK SCREWS 2900 Raised slotted head old time counter sunk S/S screws UNC x 1 inch long. Note: suitable for B Mack door handle holding screws. (B Model have odbod thread and you need to re tap to 1/4 UNC to use these screws. Price per each. See Bin FLAT HEAD COUNTER SUNK SCREWS 2929 Star counter sunk head S/S B bonnet (hood) hinge end. Holds down screws. NEW. Supplied with 2 nuts & flat washer Price per each. Bin 2900 $ 2.25 $ 1.90 SECTION 6C - GENERAL CATCHES & LATCHES - 19

23 SECTION 6C - CATCHES, LATCHES, HANDLES, CLIPS, FASTENERS, SPECIAL SCREWS ALL PRICING SUBJECT TO GST R MODEL DOOR LATCH COUNTER SUNK SCREWS 3517 Door latch holding screws. 3 Per door - 1/4 inch. PRICE PER EACH. Bin $ 1.82 FLAT SLOTTED HEAD COUNTER SUNK SCREWS 2905 Flathead S/S old time slotted head counter sunk 1/4 UNF x 1 1/2 inches long. Bin 2905 $ 1.35 B MODEL PAN HEAD 2940 Panhead S/S 3/16 x 1 1/2 UNC Headlight. Suit B73-B75, B615 and other models with aluminium panel. Bin 2905 $ 1.35 B MODEL PAN HEAD METAL SCREWS 2941 Stainless Screws to hold head light rims 4.2 x 45 long. B43-B61 etc. Suit B Mack headlight. Bin $ 1.35 B MODEL QUICK TURN PANEL SCREWS 2918 Quick turn panel screws with 10 cent coin slotted heads. 20mm diam head with 20mm quick turn shank. See Part 2919 for holding washers. Price per Each.See bin $ R MODEL STAR HEAD 2922 Starhead S/S B model Mack dash. Bin 2904 $ 0.95 R MODEL DOOR PANEL SCREWS 3516 Door panel screws. R Model. Price Per Each. Bin $ 3.00 SECTION 6C - GENERAL CATCHES & LATCHES - 20

24 SECTION 6C - CATCHES, LATCHES, HANDLES, CLIPS, FASTENERS, SPECIAL SCREWS ALL PRICING SUBJECT TO GST C CLIPS - SHUTTER 2554 Radiator Shutter C Clips - 4mm. Suit B shutter. Bin Radiator Shutter C Clips - 5mm. Suit B shutter. Bin 2923 C CLIPS - WIPER 2556 Radiator Shutter C Clips. - 6mm. Suit B wiper shaft. 2 required. Bin 2923 T CLIPS FOR HOOD LACING 1455 T steel clips for holding hood lacing to the cowling - steel - set of 28 per B Mack truck, suit other trucks & cars. - sold per each. Bin 2915 $ 0.45 CLIPS FOR B MODEL HOOD TRIM 14 Clips to hold stainless trim strips (14 per truck) 18mm fits 10mm hole sold per each- new.suit B Mack bonnet side strips. Bin 2916 $ 2.00 SPECIAL CLIPS 1456 Plastic clip for weather strip Sold per each. Suit 8mm hole and take 5mm pins. Bin 2915 $ Steel clip for weather strip. Sold per each. Bin 2915 $ Radiator top shield retainer Ford and other blind spot jobs. Nylon suit 5mm hole 10mm long. Bin $ 1.00 HELMET THREAD CUTTING MASCOT NUTS 2580 Helmet nuts - size 3/16 Hex 3/8 OD 5/8. Price Per Each.. Suit Mack Crest Mascots. Bin Mack part No 23AX503 $ Helmet Nuts - size 1/8 Hex 5/16 OD 17/32. Price Per Each. - suit original B61 badges for B model - 6 per side. Bin 2906 $ 0.75 DOME NUT 2584 Dome Nut high profile 3/16-1/4-5/16. PRICE PER EACH $ 1.65 J TYPE SPEED BODY NUT CLIPS 2589 J speed nut 3.5mm. Suit Ford. Sold per each. Bin 2907 $ J speed nut, holds B model steel door trim over edge 3/16 (4.8mm)- 13 per door. Note: if door hardware kit supplied they are included with kit. SOLD PER EACH. Bin J Nuts - 1/4. (6.5mm)Suit R Model door & dash panel. SOLD PER EACH Bin 2907 $ 2.00 $ 2.00 SECTION 6C - GENERAL CATCHES & LATCHES - 21

25 SECTION 6C - CATCHES, LATCHES, HANDLES, CLIPS, FASTENERS, SPECIAL SCREWS ALL PRICING SUBJECT TO GST J NUT CLIPS (cont) 2592 J Nuts - 5/16. Bin 2907 POA B MODEL 2593 J Nuts suitable for B model for holding fender (mudguard) panel screws 3/16 PRICE PER EACH. Bin 2913 MASCOT HOLDING CUPS 39 Stainless steel mascot cupwasher. 1/4 hole 7/8 diam. 5/16 dish. Price per each. Bin 2911 $ 4.90 $ 5.50 CONVENIENT RIVET - PETERBILT. KW Pop type rivet suitable to fill holes in Peterbilt sleepers. Can be placed from the outside with std pop rivet gun. (Note: hole in rivet needs to be filled after fitting. Price Per Each. Bin Also used on some Ford doors. $ 1.25 DOOR CLIP - B & R 3540 Retaining clip for regulator to glass support track. 25mm diam. Price Per Each. (suit R & B Model Part No & 3539). 2 required for B and early R. 1 required for late R model. Also Ford and all Chrysler Bin Door gear plate retaining clip. 1 required per door for B & R model. Bin 2914 $ 3.60 $ 3.50 DOOR LOCK RETAINER CLIPS 2912 B Model Door lock slide in retainer clip. Slides from outside to hold door lock. Width 30mm length 70mm hole 22mm. Note: if stock 118 is supplied they are in the kit, sold per each. Suits other many other models. Bin 2914 LACE HIDE ENDS 1461 Hide ends for hood lacing - 20mm. Bin See Section 6C for pricing and options. $ $ 2.10 DOOR HANDLE ESCUTCHEON 3526 Handle escutcheon. Suit door and window crank handle. Shaft size 22mm. $ Pin for window & door handle. Suit door and window crank handle. Bin 3526 $ 2.15 BONNET LATCH SPRING 161 Replacement spring for round bonnet latch, also suitable for square latches. 80mm long x 13mm wide. NEW Price per Each.. Bin 141 $ SECTION 6C - GENERAL CATCHES & LATCHES - 22

26 SECTION 6D - DRESS UP PARTS ALL PRICING IS SUBJECT TO GST MACK B JUNIOR TILT FIBREGLASS BONNET 1961 Mini tilting bonnet (hood) for custom utes (pick up truck) 2.9m (114 inches) wide to suit standard car parking spaces. Designed to suit B Mack cabin and Dodge chassis but hinge point can be changed to suit other makes and model chassis 1964 Bonnet Guard extension fits above with mounting rebate on cabin. For above. (pair) $ 3, $ MACK B TILT BONNET OPTION 1963 Maxie tilting bonnet (hood) (B615 look-a-like) suit fitting to B61 type trucks POA FIBREGLASS REAR MUDGUARDS (FENDERS) 1962 Old style rear mudguard - suit ute (pick up truck). Designed to suit 16"to 20" wheels. The guard is 1250mm long 660mm high at front & 550mm high at rear and 280mm deep, but deeper options are available for dual wheels. AUSTRALIAN OPTION UNIVERSAL ROOF VENT 1582 Cabin roof lift up solid top air vent - Australian option fits in top of cabin roof (very effective cooling a must for summer), 180x100 (7x4). Also suitable for inspection or service access doors. Trailer, canopy, horse float, rally car. $ 1, $ LARGER UNIVERSAL OPTION 1583 As above but outside dimensions - 265x214 - Cut out size 220x170 $ B MODEL AIR HORN 486 B Model Dual ORIGINAL Grover chrome short trumpet air horns - original - (per set) with valve & fittings.600mm (24Inches long) - new. $ Air Horn round dual original trumpet PA 1 Grover Copy 600mm (24 inches long). Per set- suit R or B - New. $ R AIR HORN 3439 Air horn -round single trumpet. Suit R Model. 600mm (24 inches) long $ AIR HORN RECTANGULAR 3440 Mack air horn rectangular front with snow cover with mounting kit. Suit R Mack. $ MIRROR SPOTTER 1525 Blind spot mirror, convex glass. Radius 200 x 140mm long x 100mm high $ 8.00 SECTION 6D - DRESS UP OPTIONS 23

27 SECTION 6D - DRESS UP PARTS ALL PRICING IS SUBJECT TO GST KICK PLATES - PROFILED STAINLESS STEEL MACK 1346 Fuel Tank Entry Kick Plate with Mack logo - suit B square foot opening - 320x140 profiled from polished stainless steel - per each $ Running board kick plates with Mack logo - 750x140mm profiled from stainless steel - suit early truck with long running boards. NOTE: Other sizes or vehicle brand available on request. $ DIAMOND T 23 Profiled Stainless Steel kick plate with Diamond T logo in centre- 750x140mm. $ Profiled Stainless Steel kick plate with Diamond T logo in centre- 660x90mm. $ Screws for Name Plate Mock Corners - Pan head s/taping cross recess - stainless steel M2 9X19 MACK NAME BADGES 1328 Mack cast brass side oval badge 120 x 60 suit mounting on steps, tool boxes etc. - not finished or chromed $ MUDFLAPS MUDFLAP WEIGHT & BRACKET 1336 Mudflap bottom support bracket, profiled from 6mm stainless steel 610, long & 75mm in centre with Mack logo, suitable for bending to profile of mudguard. Pair $ B MODEL CHROME HUB CAPS 2201 Mack B chrome new front axle chrome hubcaps. Fits FA 505 axle or 2203 adaptor plates. (price per each) new $ Chrome hubcaps front axle with Mack logo (not common in Australia) used - some minor rust - sold per each $ ADAPTER FOR B MODEL HUB CAPS 2203 Aluminium solid cast adaptors machined & drilled (to fit stock 2201 hubcaps to heavier axle which has flat caps) may also be used to fit caps to some rear axles-sold per each. $ MODERN TRUCKS MACK HUB 2212 Cast Alminium Universal rear hubcaps, designed to fit over wheel hub, 230 OD, 2151ID, 210 deep to suit modern 10 stud wheels with raised Mack lettering, not detailed or chromed, Price per each. $ Cast Aluminium front hub caps, designed to fit inside late American hub with raised Mack logo. $ SECTION 6D - DRESS UP OPTIONS 24

28 SECTION 6D - DRESS UP PARTS ALL PRICING IS SUBJECT TO GST STEPS - STAINLESS STEEL STEPS - CAST ALUMINIUM FOOT HOLE 1514 Foot hole recessed step -rolled top - face 165mmx140mmx90 deep - $ foothole - 115x95x90 deep - aluminium with polished face MACK B - ALUMINIUM 1515 Mack original recessed foot hole step rolled to suit round tank 560mm diameter.180mm wide x 150 deep & 240 high. SEE CAST PARTS SECTION 6H FOR COST. MACK R - 2 FOOT DIAMETER 1516 Mack original recessed foot hole. Cast aluminium. Step suitable radius to suit round tank 610 mm wide (2ft), step 370mm wide x 130mm deep x350mm high. See Cast Parts 6H General Section for cost. STEPS - PULL OUT AND FOLD DOWN 1520 Pull Out & fold down one step - zinc plated - slides under body for transport 350 wide 400 deep step, drops down. POA 1521 Pull Out & fold down two step zinc plated, slides under body for transport wide, 660 long, step drops down 530mm $ Pull Out & fold down three step - zinc plated - slides under body for transport wide, 750 long, step drops down 600mm POA STEP - FOLD DOWN 1524 Fold down entry step - cast steel suitable for fitting to rear of fuel or tool box to improve entry (for people who have difficulty climbing up into cabin). $ WATER TANK 1574 Stainless steel hand wash water tanks with flowered finish with taps with flange mounting upright - 25 litre long 240 high x 400 wide. $ Top mounted stainless 25 litre tank with rear mounting lugs high x 170 wide x 400 long. $ Brackets for above part no long x 165 deep. $ TANK STRAPPING Note: photos shows end & bolt not included 1565 Stainless steel 38mm wide flat tank straps, 2mm 304 No 8 PVC mirror finish Laser cut 1800mm long material strap only. PER EACH (Photos shows connection not included) 1566 Stainless steel 50mm wide flat tank strap 3mm 304 No 8 PVC mirror finish Laser cut 1800mm long strap only (Photos shows connection) Original type bonnet Bugler Swan ( 6 1/2")high, flat base with mounting studs & nuts. Note: Off road use only. POA $ $ SECTION 6D - DRESS UP OPTIONS 25

29 SECTION 6D - DRESS UP PARTS (cont) ALL PRICING IS SUBJECT TO GST LASHING RINGS 741 Recessed lashing rings - stainless steel tie down point anchor. Ute, light trailer. 89x76mm. Price Per Each $ Recessed lashing rings. Zinc plated. This useful steel tie down is supplied complete with moulded shroud for plant fixing to wall or floor. There is a rubber plug to prevent rattle. Mounting plate 101x95mm OD, Mounting holders 79x73mm - size 7mm. Recess 22mm. SWL 500 kg. Price Per Each 8" EXHAUST KIT Exhaust kit 8 inch stand K $ Stainless clamp 8 inch wide angle Chrome Pete 359, 68 inch mm Exhaust EL Tapered end straight section top Spool 8 inch x 55 inch (1346mm) Stack chrome 8 inch short straight section - no taper ODF x 44 inch (1067mm 981 Silicone - Hi - Temp RTV Gaster Exhaust Y Pipes. 5 inch Pete 359 (Note: this may need some changing to fit older models) Pete Exhaust mount grommetts P Stainless cab angled bracket Pete STY INCH EXHAUST KIT AS ABOVE - LIMITED STOCK $ 4, GEAR STICK KNOB 1127 Black round gear shift knob 44mm diam, no logo. 3/8 unc thread. $ Mack wooden gear shift knob $ SECTION 6D - DRESS UP OPTIONS 26

30 SECTION 6D DRESS UP PARTS (cont) ALL PRICING IS SUBJECT TO GST JOEY BOX CATERPILLAR KNOBS 1129B Knobs long (caterpillar type) for Joey box M10-M12 thread. $ R Also available in red with 3 different thread size adaptors. OLD TIME COTTON TAPE 919 Old style cotton type insulation tape,( to give your wiring the old time look). See electrical section 6E for details and pricing. STEERING WHEEL 3454 Mack optional upgrade 18" 4 spoke black steering wheel $ Steering wheel hub for above to suit R Model standard steering shaft POA No Photo FORM SHIELD (CABIN INSULATION) 1396 Form shield with silver backing heat and noise insulation - 18mm thick - Price per metre $ ARY LIZARD SKIN Lizard skin is a special sound and heat easy spray on cabin insulation. Developed in the USA for hot rods, RV vehicles and truck and sleeper, and is applied one on the other, One US gallon covers approx 18-22ft. Supplied in 2 US gallon buckets. (7.57 litres) Sound control designed to reduce unwanted noise. Improves sound system performance Ceramic insulgation designed to decrease engine and solar heat transfer. Sound and ceramic help also to seal out moisture. DEADENING PANELS 2389 Heavy duty bitumen based panels with poly propyhen covering. Self adhesive. Can be painted. Kit includes 6 panels. 550x250x2mm. Kit weight 2.5Kg. $ SECTION 6D - DRESS UP OPTIONS 27

31 SECTION 6E - ELECTRICAL PARTS ALL PRICES ARE SUBJECT TO GST REPRODUCTION WIRING HARNESS - 9 CIRCUITS Simple Universally easy to install wiring harness assembly. Has 9 circuits with pre marked fuse box wires and coded with book with wiring details. Made in USA. $ REPRODUCTION WIRING HARNESS 28 CIRCUITS Universal wiring harness assembly up-to-date and easiest to install automotive kit on the market even if you have limited electrical experience. Has 28 circuits with pre marked fuse box wires are colour coded with book of wiring details. Fuse box includes plug in flasher can and relay. Made in USA. ROUND BLINKER (TURN SIGNAL) LIGHT 772 Fender (mudguard) turn signal LED round face look a like 100mm light with chrome bezel - amber both sides - suits B & R model & other US built trucks - SOLD PER EACH $ 1, $ ROUND BLINKER RED & AMBER LENS 769 Fender (mudguard) turn single round face 12V globe type amber lens 110mm diameter. Price per Each. $ Red lens to suit above $ Amber lens to suit above $ ROUND BLINKER SIDE AMBER 3335 R Model side hood blinker lamp - Amber - Price Per Each. Complete assembly with wires. $ R TYPE CHROME SQUARE LED BLINKER 3334 R Type double side square hood blinker lamp included wiring tail. Size 115x115 lens. Note: This light has a built in side lamp chrome bezel so 3335 above would not be necessary. $ SUPERLINER STYLED DUAL FACE BLINKER 3341 Combination turn signal, side marker & park light signal with round lens. USA made, grey body with amber and red main lens. 4 wires. Replaceable globe 12V 2.1A 0.5 Park. Price Per Each. Or Supplied with 2 Amber lens Part No Add $25 BLINKER MOUNTING WEDGE (suit B Model) 774 Turn signal spacer wedge on top of front fender to level blinker light - 2 per truck - new. Sold per each. Bin 763 $ $ 9.10 BLINKER WIRING COVER BOOT 773 Turn signal wiring cover boot kit fits over wiring under fenders (mudguards) turn signal light (blinker above) - SOLD PER EACH $ BLINKER (TURN SIGNAL) INDICATOR STALK 771 B & R Model original chrome handle turn signal switch - mounts on steering column - as fitted on original with adjustable strap for other models with 7 wires. - new. $ R Model original chrome handle turn signal column switch. Mounts on steering column. 8 wires with plug $ E - GENERAL - ELECTRICS 28

32 SECTION 6E - ELECTRICAL PARTS ALL PRICES ARE SUBJECT TO GST SWITCHES DIMMER (DIPPER) - DIPPER SWITCH - TOP FLOOR MOUNTED. 914 B Model old style headlight dimmer switch - floor mounted - suit B Model & other early model cars & trucks. NEW. Bin 910. NOTE: Designed to mount on top of floor plate $ BELOW FLOOR 3389 R Series dip switch with long or short leg. Bin NOTE: Designed to mount below floor plate. $ SWITCHES - HEADLIGHT 904 B Model Original Style Push Pull head light switch with fuse - 2 positions - black knob. NEW. $ Toggle switch on-off-on $ Forward and Reverse switch 6 Amp. Use to operate mini linial actuator. See Section 6E. $ MACK STARTER SWITCH 917 Cab push starter button black knob chrome nut $ IGNITION SWITCH 856 Door & ignition lock set includes 2 door tumblers and one ignition tumbler with 2 matching keys. B88. Suit Mack B & R and lots of other makes and models. See 6C Part no 88 for door lock retainer clip. Bin 88 $ Two position ignition switch with 2 keys, Suit 3/4 inch dash hole. Made in the USA by Cole Hersee..B818. $ As Above but suit 1inch dash hole. Mack No MR3172P2. Suit B Mack, International. Made in USA..B818 $ DOOR SWITCH 805 Adjustable, suit door light/bonnet/alarm switch 10A-12V $ E - GENERAL - ELECTRICS 29

33 SECTION 6E - ELECTRICAL PARTS ALL PRICES ARE SUBJECT TO GST BATTERY ISOLATION SWITCH 785 Battery master isolation single pole switch - manual control, 250 continuous amp, volt. $ Battery isolation master switch suit car, utility or air starter trucks $ B CAB MARKER SWITCH 905 Cabmarker On/Off Switch $ 9.00 KNOBS - Dash 910 Black knobs with white (marker light engraved into knob) 3/16 UNF thread for New. $ E - GENERAL - ELECTRICS 30

34 SECTION 6E - ELECTRICAL PARTS ALL PRICES ARE SUBJECT TO GST STANDARD USA MATCHING GAUGES - BLACK FACE & BEZEL. SUIT MOST TRUCKS 3367 Speedo gauge KMH cable - 3 1/4 diam mounting hole. 3050mm cable available. $ TACHO 3369 Tacho gauge. Zero to 3200 RPM with built in hour metre cable type 2250mm luna available. 3 1/4 inch mounting hole. $ MECHANICAL OIL PRESSURE GAUGE 3372 Oil pressure gauge PSI mechanical. Suit 2 inch hole mounting. $ LOW OIL PRESSURE SWITCH 3373 Low oil pressure warning engine switch $ OIL TEMPERATURE GAUGE 3378 Gauge - Oil Temp. Transmission & Diff. Bin $ Gauge - Oil Temperature Sender for Transmission & Diff. $ VOLT METER 3377 Gauge Volt 12V 10 to 16amps battery condition and charge section $ WATER TEMPERATURE GAUGE 3380 Gauge - Water Temp Neg Fahrenheit. - Electric $ Gauge - Water Temperture Sender Unit. Negative Ground. Bin 3373 $ AIR PRESSURE GAUGE 3385 Gauge - air pressure single needle. 0-15psi. Air pipe operation $ Gauge - Air Pressure PSI Dual needle. $ E - GENERAL - ELECTRICS 31

35 SECTION 6E - ELECTRICAL PARTS ALL PRICES ARE SUBJECT TO GST STANDARD USA MATCHING GAUGES - BLACK FACE & BEZEL. SUIT MOST TRUCKS FUEL GAUGE 3387 Fuel Gauge $ USA TYPE FUEL GAUGE SENDER 3388 Sender Fuel Gauge B, R & F multi volt. Suit tank 6-24 inch deep. Suit Pal & Mack gauges. 250 ohm empty, 102 ohm half full, 310 ohm full. For Stewart Warner, Datcon, Fara, Medallion & Teleflex gauges. Supplied with instructions. MACK TACO 1030 Tachometer head, chrome bezel, black face with Mack logo. 0 to 3200 RPM with engine hours. Cable operated. Suit 85mm diam hole. $ $ E - GENERAL - ELECTRICS 32

36 SECTION 6E - ELECTRICAL PARTS ALL PRICES ARE SUBJECT TO GST AUSTRALIAN MADE CUSTOM NEW MACK LOGO GAUGES 1017 Speedometer head, black or white face with Mack logo and stainless bezel suit 85mm diam mounting hole, electrical operated in Km - zero to 120Km. OTHER MAKES ON REQUEST. $ Speedo gear box drive transducer. Bolts to standard gearbox (cable outlet) and sends signal to speedo head (part1017 above). M22 x impoulses 5mm lug. Supplied with drive key. B&R Model Macks use different drive key Drive Key x 8mm 3mm x 28mm suit B Mack & early R. For part number 1050 above $ $ Drive Key. Suit late R Mack. For part number 1050 above $ Plug for VDO gauges, except clock. PRICE PER EACH. Bin 1050 $ Plug for VDO gauges, speedo and Tacho. 8 Pin. PRICE PER EACH Bin 1050 $ TACHOMETER 1018 Tachometer head, black or white with Mack logo, stainless bezel electrical operated suit 85mm diam mounting hole - zero to 2500rpm. $ ENGINE OIL PRESSURE GAUGE 1019 Oil pressure gauge 0 TO 80PSI, electrically operated. black or white face with Mack logo stainless bezel - 50mm diam. $ ENGINE OIL PRESSURE SENDER 840 Oil sender switch 0-500KPa. Earth return oil/air ohm 1/8-27 Npts. Spade & M4 thread. $ ENGINE WATER TEMPURATURE GAUGE 1020 Water Temp gauge 40 TO 120. Electrically operated. Black or white face with Mack logo, stainless bezel - 50mm diam. $ ENGINE WATER TEMPERATURE SENDER 841 Temperature earth return water ohms, 1/8-27 NPT thread...b840 $ E - GENERAL - ELECTRICS 33

37 SECTION 6E - ELECTRICAL PARTS ALL PRICES ARE SUBJECT TO GST AUSTRALIAN MADE CUSTOM NEW MACK LOGO GAUGES VOLT METER 1021 Volt meter gauge, electrically operated, black or white face Mack logo stainless bezel - 50mm diam $ FUEL GAUGE 1022 Fuel Gauge (see Part 843 for sender) black or white face with Mack logo, Stainless Bezel 50mm. Sender not included. $ FUEL TANK LEVEL FLOAT TYPE SENDER - VDO 843 Fuel adjustable float arm sender type with 72mm daimeter top mounting plate. Suit 6-24 inch deep tanks. Supplied with fitting instruction for VDO range ohms. AIR PRESSURE GAUGE 1023 Air pressure gauge single needle. 0 to 150PSI, black or white face. Mack logo with stainless bezel 50mm. Air Pipe Operation. $ $ CUSTOM GAUGES VDO 1024 Boost gauge - black or white face with Mack logo, stainless bezel - O to 50 PSI. Photos shows optional DT logo with white face. $ Pyro metre gauge black or white face, Mack logo, stainless bezel with lead and screw in exhaust sensor - 50mm diam. Photo shows optional DT logo with white face. $ E - GENERAL - ELECTRICS 34

38 SECTION 6E - ELECTRICAL PARTS ALL PRICES ARE SUBJECT TO GST HEADLAMP ROUND 3313 New Headlamp Assembly. Fits most Macks with single round headlight and other trucks and cars, has domed lens. Supplied with lens body and lead ready for fitting Headlamp Gasket for 3313 light assembly $ HEADLAMP ASSEMBLY - OBLONG 3338 Complete oblong head light assembly RH (see part no 3332 for chrome bezel) $ Complete oblong head light assembly LH. (see part no 3332 for chrome bezel) $ AUSTRALIAN MADE CUSTOM NEW MACK LOGO GAUGES HEADLIGHT BEZEL 3332 Duel headlight bezel. Suit Superliner. 1 3/4 (45mm) deep with mounting screws. PRICE PER EACH $ INTERIOR LIGHT - UNIVERSAL - GLOBE TYPE 896 Old style interior 5 inch domed lens old style single pole. 12V globe...b818 $ UNIVERSAL LED TYPE 897 Chrome Bezel interior 150mm diam, base 30mm depth, 12V DC 0.6 Amp, current draw 40 super bright LED surface mount prewired. ON, OFF, Door switch. INTERIOR LIGHT - R MODEL 3364 R & B Dome interior light with switch and lead and suits many other models. $ DOOR OPENING LIGHT - LED 804 Door Opening light LED suit 120mm long hole x 70mm high 35mm deep with end entry plug. See part no 805 for pin door on/off switch. $ E - GENERAL - ELECTRICS 35

39 SECTION 6E - ELECTRICAL PARTS ALL PRICES ARE SUBJECT TO GST CABIN BULLET LIGHTS 3444 Bullet type curved roof lights 390mm long x 90mm diam. Suit R Model. Price Per Each. $ Bullet type curved short centre light. Suit R Model. Price Per Each. $ CURVED BASE ROOF MARKER 797 B Model original cab roof marker lights -acrylic lens - usedcondition fair to good as base plate has some rust. Rubber kit 2667 below suits this light. $ B Model cab roof chrome marker lights with curved base, acrylic amber lens (5 per truck) sold per each. They are close to the original. - New - Price per each. $ B Model Original glass amber lens to suit 797 marker lights - used - price per each. $ ROOF LIGHT ORIGINAL MOULDED EDGE TYPE RUBBER PAD 2667 Mack and other roof clearance light. Rubber glass & base pad set of 5 (10 pieces). Fit Part No. 797 used cab, very tight fit on new 796 lights. (SEE SECTION 6G - 1 FOR PRICING) PARK LIGHTS ASSEMBLY 3336 Lamp Marker Park Light Complete Assembly with wires - White. Price Per Each. Complete assembly with wires. Bin 20 $ LENS - AMBER OR WHITE 3337 Parking White or Amber Acrylic lens only - suits New. Bin 3337 $ E - GENERAL - ELECTRICS 36

40 SECTION 6E - ELECTRICAL PARTS ALL PRICES ARE SUBJECT TO GST PARK LIGHT LENS 844 E & L Mack Reproduction Diamond T & White etc park light lens ONLY. Bin1073 $ REAR LED COMBINATION LAMP 811 Quality type tail/stop/indicator lamp 9-33 volt. Super bright LED, Designed to screw from front or rear 210mm long 84 height & 33mm deep. $ Peterson USA clearance light LED amber red, 9-30V. 65 sold with chrome mounting bracket $ Peterson USA chrome mounting bracket $ 5.00 NUMBER PLATE LIGHTS 812 Number plate lights 3 LED, Steel casing 52mm bolt hole. Sold Per Pair. $ RED REPLACEMENT LENS INTERNATIONAL BLINKER LIGHTS 5050 International R190 & 200 blinker light lens truck single rear window. $ AUSTRALIAN TYPE FORD TAIL LIGHT LENS 785 Ford rear tail light lens, red, amber, clear for number plate ligh. Red Ford Script. $ E - GENERAL - ELECTRICS 37

41 SECTION 6E - ELECTRICAL PARTS ALL PRICES ARE SUBJECT TO GST OLD TIME COTTON TAPE 919 Old style cotton type insulation tape, (to give your wiring the old time look) $ MINI LINIAL ACTUATOR 901 General purpose electical push, pull ram, suitable to open vents $ and many other applications. Travel speed 6mm per second, length closed 155mm, open 205mm Max load 125kg. Supplied with in built limit switches and remote reversing switch. Can be made to fit R model air vent. EXTERNAL WIRING COVER 954 Stainless steel flexable wiring cover 11mm hole. Suit cars & trucks with exposed wiring. Bin 1073 POA HIGH BEAM LIGHT 872 B Model original style high beam light - Red lens. Bin 871 $ 8.20 CIGARETTE LIGHTER - ORIGINAL TYPE 818 Chrome knob cigarette lighter - suit B Model and most cars and trucks, (element & dash mounting) - new. $ E - GENERAL - ELECTRICS 38

42 SECTION 6F -GENERAL - PARTS BOOKS ALL PRICING SUBJECT TO GST PLEASE NOTE: ALL BOOKS ARE PHOTOCOPIES MACK B CABIN ONLY PARTS CATALOGUE 1612 Cabin parts catalogue - Standard round B Model - CA21 & CA211 as on most trucks in Australia includes assembly photos on bonnet, mudguards, firewall, floor, dash, cabin, interior, doors, cab mountings, seats, windscreen, wiper, heater, cowl, mirrors, quarter vent window, wiper motor - with Mack parts numbers for each item - 98 A4 pages 1603 Cabin Parts - B73 & B75, CA30, West Coast round type - details as above (1612) but has longer bonnet step down in floor, cast radiator. This model not common in Australia. $ $ MACK B DRIVER HAND BOOK 1605 B Model Glove box driver hand book (Petrol & diesel) pages - has general maintenance, model info, gear changing & ratios, lubrication, engine END 673 $ Glove box driver comprehensive information booklet pages, suit B, H models cooling system, operative & driving instructions for 15 & 20 speed lubrication, oil types, preventative maintenance, Thermodyne engines - 48 pages, clutch - 13 pages, gear box speed - 20 pages, air brakes - 8 pages, rear axle - 47 pages, trouble shooting - 11 pages $ MACK A DRIVE HAND BOOK $ A Model glove box drive hand book - Suit A50H, A50X, A50T, A50RT, A50S & A50RST A50 & A50T Parts Book - 56 Pages MACK L DRIVE HAND BOOK 1644 L Model Glove Box drive hand book - Suit LJT & LJSW with Cummins Engine MACK AC SALES BOOK FROM AC fully detailed specification history book with description and photos of all parts and photos of different applications including Prime Mover - Tray - Tipper - Vans - Fire Trucks - Tankers - Buses - Tower Trucks - Two Trucks - 54 Pages $ SECTION 6F - GENERAL - PARTS BOOKS - 39

43 SECTION 6F - GENERAL - PARTS BOOKS ALL PRICING SUBJECT TO GST PLEASE NOTE: ALL BOOKS ARE PHOTOCOPIES MACK B PARTS BOOKS 1620 Parts Book - B Pages. Complete part book ENDT673, turbo, engine TRQ720, guard, gear box, tail shaft with centre bearing, heavy front axle, tandem heavy rear axle. 357 pages. $ Parts Book - B615 RS Pages - Complete parts book. END 864 V8 engine, power steering, rotary injector pump, square fuel tanks, cast radiator, two disk clutch, TRQ x4 gear box, centre bearing type tail shaft, heavy front axle, heavy tandem rear axle. Cummins maintenance manual - suit NHH, Super 250, V555, VT903, NTC pages $ Cummins Shop Manual - Printed 08/ & 927 Series which include NH-23-, NHD230, NHF 240, NHC250, NHC250D, NHH25, NHF 265 Power Torque 270, NTC 290, NTF 295, NTC 335, NHHTC 335, NTC 350, NTF 365, NTA 370, NTA 400, NTA 420, NHCT-CT, NHCT 270, NHTC 295, NT 380 and 927 Series Super 250 & Super 250/ Parts Book - Great to help see how the bits fit - suit B61 RS (Note: R - is for right hand drive & S is for six wheels) Tandem. - Book is in 2 sections - Section pages - covers 711 engine & clutch - first 250 pages. 5x4 gear box FLINTSTONE 1634 R Model 1966 Flintstone with END 711 engine, square fuel tanks, cast radiator, single clutch, TRQ7220 5x4 gear box, heavy front axle, heavy tandem rear axle, steel bonnet pages $ $ R MODEL 1630 Parts Book 785 RST has ENDT 675 engine $ F MODEL 1631 Parts Book - suit F709 RT END 711 Engine - single clutch, TRQ 7220 gearbox 5x4, RHD cross shaft steering, single rear axle, steel sleeper cabin 367 Pages $ Parts book F785 RS first 8 pages, has damaged corners, 482 pages similar to book 1631 but has END T673 engine. $ SECTION 6F - GENERAL - PARTS BOOKS - 40

44 SECTION 6F GENERAL - PARTS BOOKS ALL PRICING SUBJECT TO GST MACK TRUCK SALES BROCHURE PLEASE NOTE: ALL BOOKS ARE PHOTOCOPIES 1657 B615 Sale brochure - Or see our website. $ END 864 Mack engine sales brochure - or see our website $ 1.80 MACK B WORKSHOP MANUAL Service Workshop Manual - B Pages $ B Model Workshop manual pages. Comprehensive detail with driving & gear shifting instructions, lubrication, oils, preventative maintenance, engines END P-711-END T 673, END , electrical wiring details, air starter, clutch set up, gear box quad overgear 5x4, brake trouble shooting, camber & caster, full diff assembly single axle, glass fitting. B615 heading Service Workshop Manual - B615 -RS Pages. Table of torque - 8 pages, operation detail - 15 pages, driving a Mack diesel - 5 pages, lubrication - 22 pages, preventative maintenance - 37 pages, Engine END pages, cooling system - 25 pages, electrical with wiring diagrams - 33 pages, clutch - single & double plate - 26 pages, transmission 9 & 10 speed & TRQ722 quadruplex - 25 pages, tail shaft - 5 pages, brakes - 34 pages, steering gemmer, ross, power assist with trouble shooting etc - 8 pages, front axle with sheel alignment data - 22 pages, rear axle - 16 pages, wheels - 16 pages, springs - 4 pages, chassis - 8 pages, body - 11 pages, tools - 7 pages MACK GENERAL MODELS 1628 Workshop Manual Pages - Early - Covers Models B Includes Mack C.M.B.F.R.U & Flintstone - For Engines END END ENDT ENDT673 & B - END END ENDT 864. Fuel pump, clutch, gear box, drive shaft, diffs, came with our first new Mack in 1976 MACK R WORKSHOP MANUAL 1629 Workshop Manual - covers R-RD-U & DM models Pages. Chassis, cooling, front axle, steering, springs, & suspension, wheels, brakes, elecrical. Cabs. $ $ $ $ CUMMINS MAINTENANCE MANUAL Suit NHH, Super 250, V555, VT903, NTC335, - 88 pages $ Cummins Shop Manual - Printed 8/ & 927 Series which include, NH230, NHD 230, NHF240, NHC 250, NHC250D, NHH250,NHF265, Power Torque 270, NTC 290, NTF 295, NTC 335, NHHTC 335, NTC 350, NTF 365, NTA 370, NTA 400, NTA 420, NHCT-CT, NHCT 270, NHTF 295, NT 3980 & 927 Series, Super 250 & Super 250/270. $ SECTION 6F - GENERAL - PARTS BOOKS - 41

45 SECTION 6G - CAB RUBBERS ALL PRICING IS SUBJECT TO GST. MACK B MODEL WINDSCREEN (WINDSHIELD) RUBBER 2800 B Model Mack windshield rubber moulding supplied as one piece - see part 2802 for lock strip - new. $ B Model Mack lock strip for windscreen (needs 4.1metres) and rear window, front and back needs 6.3 metres. Also suit R & B model. Sold per metre - new. $ 5.00 REAR WINDOW RUBBER MOULDING - B MODEL 2801 Rear cab (window) rubber moulding and lock strip to hold glass. 3.2m (10ft6in). - B Series. $ CAB MARKER LIGHT PADS 2667 Cab marker light moulded pad. Set of 5. Suit curved early type Mack B and other early trucks. $ EDGE TRIM DASH & GLOVE BOX SEAL - B MODEL 2538 Edge trim round edge - glass size -4 mm wide 1/8 x 6 mm x 1/4 deep. Sold per foot. Dash panel rubber mounting edge seal (1500mm). Fits over inner edge/lip to save paint. Photo shows end view. Supply 1.4m for B glove box & dash board. B & R CLUTCH PEDAL RUBBER 2482 Clutch rubber suit B & R Mack. Fits over steel plate 95mm long and 50mm wide. Can be used on many other model brake pedals. $ 5.45 $ MACK R MODEL WINDSCREEN RUBBER - R MODEL 3418 Windscreen rubber - R Series. Complete both sides. See Part no 2802 above for lock strip $ REAR WINDOW RUBBER - R MODEL 3432 Rear window rubber seal - R Series. See part no $ ROOF VENT SEAL - R MODEL 3420 Roof Vent Seal - R Series. $ VENT TRIM - EDGE B & R MACK SIDE 2621 Sponge extrusion - suit Mack. B & R Model side vent - 10mmx8mm, Sold per foot mm (27 1/2 inches) per vent. $ G - GENERAL - RUBBER. 42

46 SECTION 6G - CAB RUBBERS ALL PRICING IS SUBJECT TO GST. MACK F MODEL WINDSCREEN RUBBER - F 2804 Windscreen rubber F Model Mack $ Lock Strap for above $ DIAMOND T REAR WINDOW RUBBER - DIAMOND T 2470 Rear window rubber single glass. Suit And other Diamond T models up to Then Diamond T had White built cabins. $ Rear window double glass - suit $ WINDSCREEN RUBBER 2472 Front windscreen rubber. Suit 1950 to 1959 Diamond T and other Diamond T models up to 1959, after that Diamond T had White built cabins. $ COWL VENT RUBBER 2473 Cowl vent gasket - suit Diamond T. $ INTERNATIONAL INTERNATIONAL WINDSCREEN RUBBER 2706 Windscreen rubber suit R190, R200 with single rear back window curved dash and press button door handles. $ B CAB & RADIATOR MOUNTING INSULATOR SPECIAL CUP TYPE 154 Mack B model special cup type cab mounting insulators, 4 large & 4 small required. They are 70mm diam & 30 high with 5/8 hole. They require a 8 inch bolt at rear. See part 193 below. Sold as a set of 2 as per photo. 10mm cup machined out. 193 Rear cab mounting long bolts 8" x 5/8 with washer & nyloc nuts. 2 required per each. $ Set $ 2.50 R CABIN FUEL TANK & INSULATOR 3434 R cab and fuel tanks per each. 3 3/4 in long x 2 5/8 diam x 1 1/2 hole are split for fitting. $ G - GENERAL - RUBBER. 43

47 SECTION 6G - BONNET RUBBERS ALL PRICING IS SUBJECT TO GST. BONNET (HOOD) WOVEN LACING 2690 Woven type hood lacing - 18x5mm (3/4 x 3/16) - sold per foot $ Woven type hood lacing - 25x5mm (1x3/16) sold per foot. Also used on Ford Trucks H to C $ Woven type hood lacing - 30x8mm (1 1/4 x 3/8). Sold per foot. $ B Model rear cab end 2x1070mm per side. Supply B Model steel front 2x600. B B 61 type. B Model Alloy front 2x700. B 615 type INTERNATIONAL BONNET LACING 2696 Rubber type lacing - suit International KB1 to KB12 Model etc. 25x5mm. Sold per foot. Ex USA $ 7.30 INTERNATIONAL BONNET SEAL 2702 International hood to cowl seal. 9/16 x 3/8 high. Sold Per Foot. $ T steel clips for holding hood lacing to the cowling - steel - set of 28 per B Mack truck, suit other trucks & cars. - sold per each. Bin See Section 6C - 6 for pricing and options. BONNET LACE HIDE ENDS 1461 Hide ends - 20mm. Bin See Section 6C- 7 for pricing and options. BONNET RUBBERS - SEE BUMP STOPS LATER IN THIS SECTION 6G - GENERAL - RUBBER. 44

48 SECTION 6G - BONNET RUBBERS UNIVERSAL CORNER RUBBERS BONNET (HOOD) CORNER RUBBERS 2609 Bonnet (Hood) universal corner rubber - slip on with brass rivet - 35mmx30mm. Price per each. B2609 $ Bonnet (Hood) universal angle corner rubbers - slip on - 35mm x 35mmx43mm. Price per each. B2610 $ Bonnet (Hood) universal square corner rubbers - slip on - 45mm x 45mm. Sold per pair. B2610 $ Bonnet (Hood) universal angle corner rubbers - 60mm x 60mm.Sold per pair. B2610 $ Bonnet (Hood) universal corner rubbers - slip on - 80mmx55mmx55mm. Sold per each. $ 8.20 MACK B 2619 Bonnet (Hood) corner rubbers - suit B Model Mack. Set of 4. Note: front are different to rear. Kit cvonsists 2 front & 2 rear. 2x m = 2x 2615 cut to suit. See bin 2611 & 2615 $ INTERNATIONAL 2615 Bonnet (Hood) corner rubbers suit International R etc. Set of 2 with rivets. 75mmx47mm $ KW 2618 Bonnet (Hood) corner rubbers - suit KW slotted pad type - 50mmx50mmx50mm.Sold per each. $ KW OR AUTO CAR 2614 Bonnet (Hood) corner rubbers - suit Kenworth & Autocar - 65mmx45mmx45mm. Kit of 4. Supplied with rivets. $ BONNET WEAR STRIP 3300 Nylon cabin to hood wear strap. R Model. PER EACH $ G - GENERAL - RUBBER. 45

49 SECTION 6G - BONNET RUBBERS ALL PRICING IS SUBJECT TO GST. R BONNET & SLEEPER MOUNTING RUBBERS 2746 Bonnet pivot mounting insulators. Supplied with 2 large lower & 2 small upper. Note: this part fits some R, V/Liner, S/Liner & early Titans and cab and sleeper box mounts as well. Size 65x30 with 52x13 top. PRICE PER EACH. $ Lower bonnet mount size 52mmx13. PRICE PER EACH. $ R BONNET LOCATING ROLLERS 3298 Bonnet locating rollers. 3 inch diam 2 3/8 wide. 5/8 hole $ BONNET & MUDGUARD OPTIONS BONNET LATCH 3302 Latch hood catch, suit Valveliner and Superliner. Length centre of mounting pin to latch connect point 7 inch (180mm) overall length 13 inch (330mm) $ SOCKET CLIP FOR Clip for long rubber bonnet latch. Part No As fitted to Superliner and Valveliner. PRICE PER EACH. $ Short bonnet latch. Also suit battery box and some bonnets. PER EACH. Length centre of mounting pin to latch connecting point 4 3/4 inch x 125mm. $ SOCKET CLIP FOR Clip for short bonnet hatch. Bin 3301 $ Lower mounting kit for 3301 $ G - GENERAL - RUBBER. 46

50 SECTION 6G - BOOT RUBBERS ALL PRICING IS SUBJECT TO GST. BOOT TYPE INSULATORS GEAR SHIFT BOOT 2869 Gear shift boot rubber long 100 wide 100 high. B2870. Suit B & R Model and most other cabins,. $ TRIM RING 2868 Stainless steel surround for gear shifter boot 2869 above. $ Gear shift boot PVC high 125 wide to 18mm hole. Bin 2870 $ UNIVERSAL SHAFT BOOT 2870 Steering shaft or gear shift boot rubber - suit some R Models - 222mm long 135mm wide 70 high. B2870 $ PEDAL STEERING FLOOR BOOT 2665 Mack early oval grommet, Suit 3 inch hole in mounting plate with 2 1/4 x 1 1/2 hole centre. Bin 2870 $ STEERING SHAFT BOOTS 3097 Bearing seal 25mm shaft 65mm OD 25mm deep. $ Slip Yoke dust seal. Suit 4 splines. 1 1/4 shaft. $ G - GENERAL - RUBBER. 47

51 SECTION 6G - BUMP STOPS ALL PRICING IS SUBJECT TO GST. FLAT HEAD RUBBER SPRING BUMP STOP. SUIT MACK B & R & OTHERS 2819 Flat top spring bump stops - 58mmhigh 55mm wide. 3/8 UNF 15mm long bolt suit many other models. Suit B Mack light & heavy front axle also R Mack. Sold per each. Bin 3083 $ REMOVABLE MUDGUARD PANEL 2811 Flat top B model removable fender - 22mm wide top x 10mm deep. Sold per each. 10 Per truck. $ 6.50 SUIT GLOVE BOX, FUEL CAP ETC Universal Dome head bump stop. Size Head wide 8mm x 3mm high. S $ Universal Dome head bump stop - size head wide 9mm x 7mm high. S $ 2.75 B MACK GLOVE BOX 2828 Flat head top (glove box, fuel cap etc). 1/2 round 5/16 high, suit 1/4 inch hole. 4 Per Truck. Sold Per Each. Also GM car door & quarter glass bumper. $ 2.30 BUMP STOPS - GENERAL 2814 Flat head bump stop - 16high x 15mm wide with 8.32 thread. Also some Fords. $ Flat head top bump stop. 143mm high x 19mm wide. Also some Chevys. $ Flat head top bump stop - 12mm high x 22mm wide. Bin 2816 $ Flat head top bump stops - 19mm high x 22mm wide. Bin 2816 $ 4.30 BONNET LATCH 2846 Hood latch rubber cushion bump stop with steel backing 18mmw 12mm high. PER EACH $ G - GENERAL - RUBBER. 48

52 SECTION 6G - BUMP STOPS ALL PRICING IS SUBJECT TO GST. FLAT HEAD RUBBER SPRING BUMP STOP. SUIT MACK B & R & OTHERS 2847 Hood latch replacement cushion rubber - NEW. Not as thick as PER EACH $ 5.55 INTERNATIONAL 2703 International truck bonnet to mudguard bumpers and corners. Suit US built International L,R,S bumpers & 2 corners. PER SET. B2615 $ ADJUSTING BONNET TYPE BUMP STOP 2818 Flat head top bonnet (hood) adjusting bolt with bumper, chrysler to 1960's upwards & other models where adjustment of height is required 31mm wide 13mm deep 30mm long bolt. 3/16 UNC. Bin 2816 BUFFER DOCKING TYPE BUTTERS 2822 Block type bump stops 75mm high 155 mm long at 65mm base. 2x15mm mounting holes $ 7.30 POA 2823 Block type bump stops 50 high 195mm long 55mm wide 2x10mm mounting holes POA 2824 Block type bump stop 90mm high 150mm long 75mm wide. 2x12mm mounting holes POA 2825 Block type bump stop 95mm high 200mm long 145mm wide with 4x15mm mounting holes. POA 6G - GENERAL - RUBBER. 49

53 SECTION 6G -DOOR RUBBERS ALL PRICING IS SUBJECT TO GST. B DOOR BAILEY FLEXIBLE CHANNEL - GENERAL 2501 Bailey channel flexable, stainless steel bead, rubber covered, pile & felt lining suit Mack, Ford 52-56, Chrysler 55-56, Studebaker 53-62, Willys SOLD PER FOOT, EX USA, 15 mm wide, 15mm high & Bead. $ DOOR RIGID PILLAR BAILEY CHANNEL 2510 Bailey channel rigid, pillar channel, stainless steel bead, pile lining, 12mm wide 13mm high & bead. Suit Mack B&R. PRICE PER METRE DOOR BAILEY FLEXIBLE CHANNEL - SUIT R & F MODEL MACK 3549 Channel Bailey - Mack R&F. 2 per door. Price Per Each Door. Supplied with 5 clips. $ BELT STRIP DOOR SQUEEGEE - UNIVERSAL 2512 Half Bailey channel, rigid weather strip, stainless steel, rubber covered, pile lining, 8mm thick 15mm high. Sold per foot. Ex USA $ 6.85 UNIVERSAL DOOR GLASS SQUEEGEE SET 2513 Set of 4 sqeegee door glass guides for glass to glide on. Universal set suit lots of makes and models. 420mm long 12mm deep 6mm thick. NA B & R & F DOOR GLASS SQUEEGEE INNER 3550 Weather strip B & R & F model door glass squeegee guides.- 2 required per door L & R. Price Per Each. Note on R & F, only one per door if wiper type below option is used. $ R & F DOOR GLASS SQUEEGEE OUTER OPTION 3546 Weather strip R&F model door glass squegee guides with rubber wiper seal and door lip - RH (one per door) $ Weather strip R&F model door glass squegee guides with rubber wiper seal and door lip (one per door) - LH $ DOOR KITS DOOR KIT - B MODEL 2511 B Model door glass rubber channel curved radius kit, includes flexable lining bailey channel with stainless steel bead for curved radius top of door. One rigid & one flexable for removable window panel in door and 2 sqeegee glass guides for glass to glide in. B Model door kit - 5 pieces. DOOR KIT - R MODEL 3552 R Model door glass channel curved kit. Top of door 2 channel for removable window panel and 2 squeegee glass guides. $ $ no photo 6G - GENERAL - RUBBER. 50

54 SECTION 6G - DOOR RUBBERS ALL PRICING IS SUBJECT TO GST. DIAMOND T CAB RUBBER KITS 2467 Complete rubber cabin kit for Diamond T type cabin - R190 & R200 with single rear window and press button door handles. $ 1, INTERNATIONAL CAB RUBBERS CURVED DASH MODEL ONLY 2704 Complete rubber cabin door kit for USA type cabin 32 pieces - Late R190 & R200 with single rear window, curved dash and press button door handles. $ 1, DOOR SEAL - B MACK 2560 D shape car, truck, door hollow weather strip adhesive backing. 14mm wide x 15mm high. Sold in 4 metre lengths $ SPECIAL DOOR SEAL - R MACK 3558 Rubber super soft hollows door seal. Adhesive backing. Fits in cabin door, closes against it. 13mm wide 18mm high. Sold in a 4.5m (15ft) length. Note: 4 metres per door. $ DOOR SEAL - INTERNATIONAL 2697 International lower door seal KB & L, R, S. US models. Lower door seal mm long 15mm wide T pop. Sold Per foot. $ International door seal front of cabin. US models single rear window mm x 5mm Sold per foot $ 3.80 INTERNATIONAL TRUCK DOOR SEAL GUARD 2699 Quarter round sponge square back type - 12x12., Sold per foot. $ Sponge extrusion - 12x12. Sold per foot. $ 3.80 DOOR QUARTER VENT SEALING RUBBER - SUIT B MODEL MACK - NEW 2452 Quarter Vent window rubbers (pair) - fit to door to seal pivot glass closing to frame - new. Sold as pair only. $ DOOR QUARTER VENT SEALING RUBBER - SUIT B MODEL MACK - USED 2453 Quarter vent rubber complete and pliable - suit older restoration job. - Used. L & R. Price Per Each. $ B DOOR QUARTER VENT WINDOW POST SEAL 2454 B model vent window post rubbers (seals glass vent to the rear upright post when glass is closed straight). Sold per each - 2 required per truck. $ G - GENERAL - RUBBER. 51

55 SECTION 6G - DOOR RUBBERS ALL PRICING IS SUBJECT TO GST. R MODEL MACK 3571 R Model vent window flipper (quarter vent) outer rubber seal LH only $ R Model vent window flipper (quarter vent) outer rubber seal RH only $ DIAMOND T NOTE: DIAMOND T CABINS WITH 2 BACK WINDOWS SAY MODEL etc USE A SHORTER DOOR QUARTER VENT RUBBER Quarter vent rubber set, Diamond T type cabin with twin rear window etc models. As 2468 above but not as long. $ Quarter vent rubber set for Diamond T type cabin, with single back window and press button door handles. $ INTERNATIONAL 2705 Quarter vent rubber set for USA type cabin. Late R190 & R200 with single back window and curved dash and press button door handles. $ DOOR GLASS SETTING CHANNEL & QUARTER VENT GLAZING SEAL - HOLDS GLASS IN PLACE Quarter vent and door glass holding rubber. 400mm per B door, 700mm per B vent. Softens with kero to help fitting. When dried makes strong bond to glass. Used with door glass channel lifter and quarter vent glass in its frame and some windscreen and glass frames. Sold per metre. 1 1/2 WIDE X 1/16 THICK. (1.5X87MM). $2.18 per 200mm. $ G - GENERAL - RUBBER. 52

56 SECTION 6G - ENGINE & CAB INSULATORS ALL PRICING IS SUBJECT TO GST. B ENGINE MOUNTING INSULATORS 169 Mack B rear engine and gear box mounting rubber. Set includes 4 upper & 4 lower. They are 70mm dia & 30mm high with 5/8 hole. Sold Per set of 4 (8 PIECES) $ (4 sets) R MODEL ENGINE MOUNTING INSULATORS 2745 Mack engine mounting rubber. Fits some Flintstones, R Model, V/Liner, Superliner, Ultraliner, Cruiseliner etc from about 70's to around 1990's, where they run 8 rear engine mounts, also used as front engine mount on some models. Note: Very common engine mount. Size of 2745 & 2747, 80mmx20mm deep with 50mm wide X18 centre. Lower number dependant on model. 8 standard mounts. Price Per Each HEAVY DUTY ENGINE MOUNTING INSULATORS 2747 Top harder rubber yellow dot used on rear top mount. 4 per truck. Price per Each. $ $ CENTRE BEARING & SHOCKER RUBBER 2674 Centre bearing rubber, also fit some shockers. 25mm hole, 50mm big end, 40mm small end & 28mm deep $ G - GENERAL - RUBBER. 53

57 SECTION 6G - FLOOR MATS ALL PRICING IS SUBJECT TO GST. FLOOR MATS -MOULDED MACK 2761 B61 type ribbed moulded front floor mat with Mack logo and heavy backing $ B61 type ribbed moulded floor mat with heavy backing (goes under seat) $ B61 type straight ribbed front floor mating cut out of rubber sheeting to original size. No Mack logo. Straight wide grooves. See part no 2640 below for photo. $ B61 type rear floor mating cut out of straight ribbed rubber sheeting, straight wide grooves. $ R FRONT FLOOR MAT 3391 R Model front floor mat - moulded rubber ribbed with Mack logo & wear section on LH side. $ REAR FLOOR MAT 3392 R Model rear floor under seat mat - moulded ribbed rubber $ R Model plain floor mat (no ribs etc) supplied in one section. MAKE YOUR OWN FLOOR MATS 2640 Roll of big rib rubber sheeting 2m wide - make your own floor or ute tray mat - SOLD PER FOOT. $ LOOSE FLOOR MATS 2771 Loose floor mats with Mack logo L&R. Weight 2.5Kg. SOLD PER PAIR $ G - GENERAL - RUBBER. 54

58 SECTION 6G - GENERAL RUBBERS ALL PRICING IS SUBJECT TO GST. ADHESIVE - NO SLIP ADHESIVE Black high grip non slip adhesive backed rubber. 150 wide - sold per metre. $ 9.00 DRAG LINK COVERS 303 B Model Drag link leather grease covers with lace - new $ EDGE TRIM DASH & GLOVE BOX SEAL 2538 Edge trim round edge - glass size -4 mm wide 1/8 x 6 mm x 1/4 deep. Sold per foot. Dash panel rubber mounting edge seal (1500mm). Fits over inner edge/lip to save paint. Photo shows end view. Supply 1.4m for B glove & dash board. $ Edge trim round edge - 12mmx10mm (1/2x3/8). Sold per foot. $ Edge trim square edge - 7 mm 1/4 wide x 8 mm 5/16 deep. Sold per foot. $ Edge trim - round edge - 12 mm 1/2 deep x 10mm 3/8 wide Sold per foot $ Edge trim - square back 7mm 1/4 x5mm 3/16. Sold per foot. $ Edge trim - round edge - 12mm 1/2 wide x 12mm 1/2 deep. Sold per foot. $ GASKET RUBBER RADIATOR 2860 Rubber gasket suit top and bottom radiator tanks - B615 & 75 and the like. 2mm thick 30mm wide. Sold per metre $ G - GENERAL - RUBBER. 55

59 SECTION 6G - GENERAL RUBBERS ALL PRICING IS SUBJECT TO GST. MAKE YOUR OWN FLOOR MATS 2640 Roll of big rib rubber sheeting 2m wide - make your own floor or ute tray mat - sold per foot. $ OIL ENGINE Castrol RS Super 15w-40 engine oil. Sold Per Litre. Workshop Only. $ 6.00 PINCH WELD 2882 Pinch weld - suit Peterbilt sleeper doors $ RUNNING BOARD RUBBER 2641 Ribbed running board rubber strip 425mm wide. Sold per metre. $ SLEEPER CAB SEAL 2639 Universal sleeper seal, an efficient seal designed to connect and seal crawl space between the driving and sleeping cabins in trucks. 150 wide x 25 deep. Sold per metre (4m = 1Kg) $ SPONGE EXTRUSION 2563 Sponge - 8mmx10mm. Sold Per foot. $ Universal door seal. Soft seal fits most cars. 13mm wide x19 mm high. Sold per metre $ 4.55 VENT TRIM - EDGE B & R MACK SIDE 2621 Sponge extrusion - suit Mack. B & R Model side vent - 10mmx8mm, Sold per foot mm (27 1/2 inches) per vent. $ Sponge extrusion 20x10mm. Sold Per Foot. $ Sponge Extrusion 13 x 7mm. SOLD PER METRE $ Universal rectangular stick back seal rubber. 3/8 inch wide 3/16 high. (9mm x 5mm ) Sold Per Foot. $ Sponge seal square extrusion with sticky back - 20mmx12mm. Sold per foot $ G - GENERAL - RUBBER. 56

60 SECTION 6G - HOSES ALL PRICING IS SUBJECT TO GST. HOSE SILICONE COOLANT BLUE 2720 Silicon Hose - 1 inch (25mm). SOLD PER 100mm. $ Silicon Hose 1 1/2 inch (38.1mm) sold per 100mm $ Silicon Hose - 2 inch (50.8mm) Sold per 100mm $ Silicon Hose 2 1/2 inch (63.5mm) Sold per 100mm. $ Silicon Hose - 3 inch (76.2mm) Sold per 100mm $ Silicon Hose - 4 inch (101.6mm) Sold per 100mm $ Silicon Hose - 5 inch (128mm) Sold per 100mm $ Silicone hose 6 inches (2.250mm) Sold per 100mm. $ SILICONE HOSE -BLACK (OLD TIME) 2730 Silicone hose 2 1/4 inch (57 ID). SOLD PER 100mm $ Silicone hose - 3 inch (76mm). SOLD PER 100mm $ Silicone hose - 4 inch (1.2mm). SOLD PER 100mm. $ AIR INTAKE FITTINGS 2739 Air hose hump connector, straight, suit 5 inch tube. Suit Superliner. $ Air Hose hump straight suit 6 inch tube $ Air elbow 38deg. Suit 5 inch tube POA 2743 Air elbow 90 deg suit 6 inch tube. Suit Superliner $ Air elbow 90 deg. Suit 5 inch tube $ Air elbow 90 deg suit 6 inch tube. $ FOR AIR BRAKE HOSE (SEE BRAKE PARTS) 6G - GENERAL - RUBBER. 57

61 SECTION 6G - MUDGUARD ALL PRICING IS SUBJECT TO GST. HEAD LIGHT PANEL MOULDING SEAL - MACK B 2565 Suit head light panel to radiator - B Mack, very flexible, 7mm piping, 30mm flat section, suit many applications. Beaded vinyl moulding seals headlight panel to radiator shell and to outer mudguard. Note: Special rubber edge trim can also be used but extra work normally takes 650 per section or 2600 per truck size 40mmx10mm. (note: & 75 only need 1300) SOLD PER METRE. $ T SECTION 2785 T Section joint rubber - 50mm x 10mm. SOLD PER METRE $ ROUND SECTION 2552 Round edge seal - 25mm x 7mm. SOLD PER METRE. $ INTERNATIONAL MUDGUARD SEAL 2701 International rear mudguard ribbed rubber welt 5/16 x 1 inch. Sold per foot. $ 4.50 HOLLOW PIPE SEAL 2792 Hollow pipe joining rubber - 35x11. SOLD PER METRE. $ MUDGUARD (FENDER SEAL) MACK B 2685 Mudguard to cab edge fenderwelt seal - 40Wx8Hx8W. Sold per foot. Ex USA $ G - GENERAL - RUBBER. 58

62 SECTION 6G - MUDFLAPS ALL PRICING IS SUBJECT TO GST. MUD FLAPS - REAR 3086 Mack mudflaps - white with facing dogs, as on Bicentennial Super Liner. 600 w, x 400 drop. Australian made. 4kG PER PAIR.PRICE PER EACH $ MUDFLAPS - SUIT UTILITY (PICK UP) 1198 White heavy mudflap ute 280mm (8ins) wide c 280mm (11ins) deep. Australian made. Sold per each $ Rear mudflaps - heavy black rubber with white logo - 30" or 36" Mack log - sold per pair. Made in USA. L&R facing dogs. NEW. (13kKg PER PAIR) $ Rear black mudflap suitable for fitting straight half mudguard as the provision for bolting holes are in the bottom, can be used for front flaps by redrilling holes in the top. 610mm (24ins) wide x 150mm (6ins) high with MACK in white writing. Made in USA. Sold Per Set Mud Flaps - Diamond T mudflaps, white with red markings wide x 460 drop. Note. We must order 50 at a time, so would need some interest on numbers to do another batch. $ POA FRONT MUDFLAP 3340 Mudflap bonnet LH & RH, R Model black. Not Valveliner. Supplied with brass eyelets and top rebate. PRICE PER EACH $ G - GENERAL - RUBBER. 59

63 SECTION 6G - SPRING RUBBERS ALL PRICING IS SUBJECT TO GST. FRONT SPRING INSULATOR 2751 Front spring insulator. Suit B61 and most other B models $ ELEPHANT FEET INSULATOR 2758 Top insulator suit steel base, 6insx4 1/2 ins 1 3/4 dowel. 4 Required. Price Per Each $ Top insulator - suit Required $ Top insulator, suit early with smaller locating dowel. Note: these are modified in our workshop to 33mm dowel, top plate 6 x 4 1/2 inch, 3 inch deep & dowel. Cost to modify add $35 $ Lower insulator. Suit & rear end. Steel Base 6 1/8 x 6 1/8 1 3/4 dowl. 4 Required. Price Per Each $ Side Spacer of lower insulator Neoprene. 8 Required. Price Per Each. $ SPRING INSULATORS - DIAMOND T 2479 Front spring shackle rubbers 1 3/4 inch diamater x 2 7/8 inches high Price Per each. Allow 4 to 5 weeks for delivery $45.00 front 2480 Diamond T rear bush set. Allow 4 to 5 weeks for delivery. Sold Per Each $ G - GENERAL - RUBBER. 60

64 SECTION 6G - TANK & TOOL BOX STRAP ALL PRICING IS SUBJECT TO GST. TANK STRAPPING SQUARE EDGE 2525 Fuel/ air etc tank strapping - square edge - 32mm ID, Sold per metre $ Fuel tank strapping - square edge - 38mm ID Sold per metre 2528 Fuel tank strapping - square edge - 50mm ID. Sold Per Metre. $ Fuel tank strapping - square edge - 80mm ID. Sold Per Metre. $ TANK STRAPPING - ROLL OVER EDGE 2520 Fuel tank strapping - rollover - 40mm ID $ SAMPLE PHOTO 2521 Fuel Tank strapping - roll over - 50mm ID $ Fuel tank strapping - roll over - 63mm ID 2523 Fuel tank strapping - rollover - 80mm ID FUEL TANK STRAP ROLL 3085 Rubber Fuel Tank Strap 50mm ID - 2 inch. Comes in bag of 25ft. (7.6m). $ SAMPLE PHOTO R FUEL TANK FLAT STRAP 3084 R Mack fuel tank flat strap. 2 1/8 wide, 1/8 thick, (has no edge turn up) SOLD PER FOOT. $ 4.00 EDGE TOOL BOX STRIP 2561 Sponge tool box flat strip, super fine with stick back - 18mmx 1.6mm $ 2.55 TANK SUPPORT RUBBER 3434 R fuel tanks support rubber. Price per each. 3 3/4 in long x 2 5/8 diam x 1 1/2 hole are split for fitting. $ G - GENERAL - RUBBER. 61

65 6H - REPRODUCTION CAST PARTS ALL PRICING SUBJECT TO GST F MACK MODEL BADGES 3326 F Mack side and glove box badge, cast from brass, detailed and chromed long x 34mm high. Price per each. $ R MACK MODEL BADGES 3324 R600 cast from brass, detailed and chromed. $ R700 cast from brass, detailed and chromed. $ R800 cast from brass, detailed and chromed $ B MODEL HOOD/BONNET MODEL NUMBERS 8 Chrome model hood emblem recast from brass, not finished or chromed. Models available - B20, B42, B57, B60, B61, B73-B85, B95, B422, B421, B615, B815, H60 - W71. For hand detail and chrome plated add extra $ Bin 8. Note: We can make any model number but a new pattern cost would apply of $60.00 $ V8 EMBLEM - NOTE ONLY ON SOME MODELS 205 B Model V8 bonnet emblem, cast from brass - not finished or chromed - sold per each. $ B Model V8 chrome emblem, detailed & chromed with threaded pins. All models which had a chrome badge. Gold available. 90mm wide 60mm high and 8mm thick. Sold per each.bin 205 $ THERMODYNE BADGE 292 Thermodyne script badge - not finished or chromed - 2 required (Price per each) 36 B Model Thermodyne badge, fully hand detailed and chromed, fitting pins in bonnet and they are nice and straight - new - (Price per each) $ $ DIESEL BADGES 87 Diesel script badge, cast from brass, not finished or chromed. $ Diesel script badge, cast from solid brass, detailed and chromed, fitting pins fit holes in original bonnet. $ L SERIES MACK BIG DIESEL BADGE 1946 Diesel side badge - suit L model. 9" long x 2 1/4 deep $ As Above but detailed and chrome plated. $ to 1945 LTL or LTH BADGES - MADE TO ORDER POA 6H-GENERAL REPRO CAST PARTS 62

66 6H - REPRODUCTION CAST PARTS ALL PRICING SUBJECT TO GST B MODEL MACK CHROME SCRIPT 70 B Model chrome "Mack" script for Hood sides, cast from brass not finished or chromed. L&R. Sold per each. Bin B Model Chrome "Mack" script for Hood Sides - L&R -NEW - Sold per each. Detailed and chromed. MACK CASTING 1328 Mack cast brass side oval badge 120 x 60 suit mounting on steps, tool boxes etc. - not finished or chromed $ $ $ Mack script cast from aluminium and shaped so when fitted to a body it looks like a pressing 300mm long 90mm high. $ (Mack) Jr letters. Cast from aluminium and so shaped, so when fitted to a body it looks like a pressing. Note: photo shows 1325 (Mack) above this not included in price. $ Mack Aluminium script 115x50 - suit fitting into foot grates etc. $ MACK DOGS 1329 Mack oval raised cast script with dog on top - logo - 48x44mm - extra for chrome plating. Suit axle ends, steering wheel centres $ Mack oval raised cast script with dog on top, 230 long 150 high 15mm thick. Dog Oval 10mm thick. $ B MODEL MACK HALF DOG 10 B Model half dog emblem - hood sides - left & right - sold per each - NEW - 2 required $ B Model half dog - used all have some pitting $ CURVED DOG BASES MOUNTING - STEEL COWL 4 B 61 and similar Model Curved Base for Bulldog Hood Ornament - Chromed - New. Ex USA POA 33 B61 Model curved dog base for bulldog hood ornament with some pitting, maybe OK for rechroming - USED. $ H-GENERAL REPRO CAST PARTS 63

67 6H - REPRODUCTION CAST PARTS ALL PRICING SUBJECT TO GST CURVED DOG BASES MOUNTING - STEEL COWL (cont) 33a B61 Model curved dog base as above but special type rechromed. $ B61 Model curved dog base for Bulldog Hood Ornament, cast from brass, not finished or chromed or tapped. - new. Add $184 for detailing, drilling & chroming. $ LATE MACK HALF DOG 3270 New Mack logo standing half dog. Left and Right, facing each other. Cast from brass, detailed and chrome plated. PRICE PER EACH. Also available in gold colour. $ New Mack logo letters. Set of 4, cast from brass, detailed and chrome plated. Price per Set of 8 letters. Bin 3270 $ CAST RADIATOR BADGES MACK AB 1743 AB Mack radiator cap with motor metre mounting hole with inside thread. Cut. $ MACK CHASSIS PLATE - CAST ALUMINIUM 1747 Mack AB type rear cross member name script plate, cast from aluminium painted green with yellow Mack script cast to look like the original raised enamel plate - 450x110x6mm $ AK MACK PARTS 1700 AK Mack new aluminium top radiator tank - as per original fitting, not machined & drilled. $ 3, AK Mack new aluminium LH lower radiator tank - not machined & drilled. $ SAMPLE PHOTO 1702 AK Mack new aluminium RH lower rdiator tank - not machined & $ drilled AK Mack new aluminium hose fitting POA 1704 AK Mack new aluminium hose fitting, not machined & drilled. Note: AK are larger capacity radiators - check size before ordering. POA SAMPLE PHOTO NO PHOTO AVAILABLE NO PHOTO AVAILABLE 6H-GENERAL REPRO CAST PARTS 64

68 6H - REPRODUCTION CAST PARTS ALL PRICING SUBJECT TO GST AC MACK PARTS 1715 AC 1927 sales book - 56 pages. $ Original AC radiator cap mascot. 50mm round badge. $ NO PHOTO AVAILABLE 1721 AC Mack top radiator tank, as per original detail & dimensions - not machined or drilled. $ 3, AC Mack - LH lower tank as per original - not machined or drilled $ AC Mack - RH lower radiator tank as per original detail & dimesnions, Not machined or drilled. MACK E SERIES 1741 EH side cigar emblem script plate, Cast from brass not finished or chromed. Suit E series & similar year models. Price per each. $ $ EH type short mount grille & dog mount - not finished or chromed $ A E type long radius type grille & dog mount, not finished or chromed $ MACK JR SERIES 1967 JR round grille badge - 80mm (3 1/8) diameter, not finished or chromed. $ JR curved radiator cap surround with Mack name emblem. 75mm (3 inch) diameter, not finished or chromed but machined. $ JR radiator cap cover & dog base. Small dog part no. 660 mounts in holes. This cover screws on to part no Bin $ JR hood (bonnet) side cigar type script plate. 380 long x 50mm wide. Not finished or chromed. Price Per Each $ TYLDEN B MACK JUNIOR RADIATOR MASCOT 1965 Tylden B Junior ute radiator mascot & dog base. Special for fibreglass bonnet. POA 6H-GENERAL REPRO CAST PARTS 65

69 6H - REPRODUCTION CAST PARTS ALL PRICING SUBJECT TO GST MACK JR HUB CAP CENTRE 1966 Mack JR hub cap centre. Hex base (85mm wide) 3 1/4 inches (12mm) thick. Not finished or chromed. B1977 $ SMALL RAISED DOG 1353 Mack raised dog cast from aluminium. 200 long, 140 high x 20mm thick. $ LARGE RAISED DOG 1351 Mack raised dog cast from aluminium with hollow back section part., 760 long 670 high 65mm thick. $ PAINTED OPTION OF Mack big dog 760 long 670 high x 65 deep air brushed - hand painted - high quality finish then clear coated. Suitable for in or outside mounting. Weight 8kg. $ MACK CAST STEP PLATE 1301 Step plate early Mack logo 280 long x105 high. 10mm deep - cast from aluminium. Not drilled or detailed. $ Mack cast step plate 470mm long x 120mm wide. Not drilled or detailed. $ B MACK FLOOR MAT EDGE COVER 1348 B Model cast polished aluminium kick plate with Mack logo to cover edge of carpet (mat), priced per pair - NEW. B61 type cabin - not suitable for B73 or B75 without splicing. Also available cast from brass and chrome plated. $ B MODEL FOOT VALVE CURVED PEDAL 582 New RHD Curved brake pedal with Mack logo. Fit late pedal adapter. Casting only, not drilled or detailed. NEW $ R MODEL FOOT VALVE PEDAL 3074 New brake pedal with Mack logo. Note: holes are not drilled. $ BIG BASE MIRROR DOOR BRACKET piece mirror arm bracket mounting set. LTL type. Suit lots of models & makes. POA 6H-GENERAL REPRO CAST PARTS 66

70 6H - REPRODUCTION CAST PARTS ALL PRICING SUBJECT TO GST SUNVISOR CENTRE BRACKET 1092 Sunvisor centre bracket to suit steel sunvisers. Sold as a casting with deep lug for different shape and angel visors. Not finished, need to be adjusted to your truck and drilled for chroming. $ FUEL TANK CAPS - LARGE 262 Brass fuel cap large type with four lugs - Snyder Buffalo cast from brass & machined with new 100mm thread 130mm Top - new $ FUEL TANK CAPS - SMALL 273 Brass fuel cap 55mm thread (2 1/8). Top 70mm (2 5/8) Snyder - Used $ FUEL TANK FILLER 363 Fuel tank filler tube aluminium for welding into tanks to take large B (part 262) filler caps. Note: not machined - new. POA 363a With clean up and new thread for Buffalo cap 262 ready for welding into tank POA FUEL TANK TAP 1395 Fuel tank Brass stop tap - new - 1/2 female, 1/2 male, NPT thread with round gate wheel handle - looks like original. See Axle/Chassis Section for options and prices. MICHELIN MAN 1375 Cast Bibendum tyre Michelin compessor man on base high $ Cast Bibendum tyre Michelin man 200mm high 140mm round base. $ Cast Bibendum type wall mount Michelin man 460mm high $ Solid cast Bibendum tyre Michelin man 240mm high $ H-GENERAL REPRO CAST PARTS 67

71 6H - REPRODUCTION CAST PARTS ALL PRICING SUBJECT TO GST SPECIAL CAST NAME SCRIPT BADGES 1319 TYLDEN HERITAGE - 30mm high - cast from brass and chromed. $ CUSTOM BUILT -30mm high - cast from brass & chromed. $ CUMMINS PLATES - CAST ALUMINIUM 1272 Cummins Diesel cross mounted on raised polished backing with two mount bolts can have engine model - 190x110 - new $ Cummins 290 cast model chrome plate - size 6 1/2x 1 5/8 inches (165x40mm) - new $ Cummins 400 cast model chrome plate - size 6 1/2x 1 5/8 inches (165x40mm) - new $ STEPS - CAST ALUMINIUM FOOT HOLE for ROUND TANK 1515 Foot hole recessed step suit Mack US round fuel tanks, 560mm diameter. Foot hole 175mm wide, 145mm deep, 200 high. Suit hole 190mm W x 230mm H. NEW. Price per each. $ MACK R 1516 Mack original recessed foot hole. Cast aluminium. Step suitable radius to suit round tank 610 mm wide (2ft), step 370mm wide x 130mm deep x350mm high. $ AMERICAN EAGLE 1371 American wall mounting eagle. 790mm wing span $ American wall mounting eagle 790mm wing span hand painted. $ MACK DOOR LOCK 1976 Roto-Lokit door. Suit Mack Chrysler, Dodge, DeSoto , Plymouth , Studebaker , Nash , Packard , suit right front or rear left. Cast from brass, not drilled or detailed. Bin $ H-GENERAL REPRO CAST PARTS 68

72 6H - REPRODUCTION CAST PARTS ALL PRICING SUBJECT TO GST REPLACEMENT STRICKER PLATE 1385 New replacement stricker plate catch. Plate cast from brass. L&R side supplied with stainless bolts..b95 Bin 385 $ BLINKER MOUNTING WEDGE (suit B Model) 774 Turn signal spacer wedge on top of front fender to level blinker light - 2 per truck - new. Sold per each. Bin 763 $ H-GENERAL REPRO CAST PARTS 69

73 6H - REPRODUCTION CAST PARTS ALL PRICING SUBJECT TO GST DIAMOND T CAST PARTS 1753 Cast Aluminium hub caps. Note: These do not have holding clips and may not fit on some axle spigots. They do not have outside lip to allow fitting with external screws. Size 230mm diameter plus locating lip 80mm deep. Hole ID inside 215mm. Also available with Mack logo. Not chromed Cast aluminium bumper bar top step to suit model Diamond T Bumper bar top step thread plate as per original 360long x 160mm wide at large end. Sold as left & right. (per each) Not drilled Cast aluminium grille curved badge. Curved front grille badge - suit 531 & 630. Size 210x210mm. Not chromed. Add $50 extra for chrome. $ $ $ Cast aluminium side bonnet badges. Side bonnet badges - 180x100mm. Note: These have been made smaller than original as we believe originals look too big. Not chromed. Add $45 extra for chrome. Bin Cast bronze dash & upholstery badge (fits in plate DT21 below). Small dash plate badge also suitable for door trims. 45x25mm. Not chromed. Add $15 extra for chrome. $ $ Brass Dash Plate. Round dash plate - 130mm diam. Fits in left hand hole in dash - Diamond T models. Stock No Diamond badge fits in its centre. Not chromed. $ Cast aluminium step plates. Diamond T step plate mould based on original rubber step with Diamond cast in centre. 680 long x 220 wide. Not chromed. $ Cast aluminium step plates. Diamond T step plate. The mould based on original rubber step with Diamond cast in centre. 790 long x 150 wide. Not finished or chromed. $ INTERNATIONAL 5052 International Loadstar V8, 1800 side badge, cast from brass not finished. 140 long x 75mm high. Bin 5052 $ H-GENERAL REPRO CAST PARTS 70

74 6H - REPRODUCTION CAST PARTS ALL PRICING SUBJECT TO GST CHAMBERLAIN 1361 Front grille plate, cast from brass, not detailed or chromed $ Front up and down grille plate, (TYPE DIESEL) cast from brass, not detailed or chromed $ DA Diesel side badge cast from brass, not detailed or chromed. $ KEITH SIDE BADGE 1365 KEITH side badge 185mm long x 65 high. Nor finished or chromed. $ H-GENERAL REPRO CAST PARTS 71

75 6I - STEEL INSTRUCTION & PATTERN PLATES ALL PRICING SUBJECT TO GST STEEL NAME PLATES - MACK GEAR SELECTION 1207 MACK STEEL PRINTED GEAR SHIFT PATTERN PLATES AUXILIARY TRANSMISSION 152mmX65mm. Bin 1208 $ MACK TRANSMISSION 5 SPEED DIRECT - 95mmX65mm. Bin 1208 $ MACK UNISHIFT - DO NOT USE 5 IN LOW - 152mmX65mm Bin 1208 $ MACK - 9 SPEED OVERGEAR TRANSMISSION - 150mmX65mm Bin 1208 $ MACK - 10 SPEED DIRECT TRANSMISSION - 150mmX70mm Bin 1212 $ MACK - 10 SPEED OVERGEAR TRANSMISSION - 150mmX70mm. Bin 1212 $ MACK - TRT - 72 TRIPLEX 15 SPEED - 152mmX65mm Bin 1212 $ MACK - TRO - 72Q - QUADRUPLEX (20 SPEED OVERGEARED) 152mmX65mm. Bin 1212 $ MACK - 18 SPEED QUADRUPLEX (20 SPEED OVERGEARED) 152mmX65mm. Bin 1212 $ MACK - LTL GEAR SHIFT PATTERN 5 X 4-130mmX80mm. Bin 1307 $ SECTION 6I - ENGINE PLATES 72

76 6I - STEEL INSTRUCTION & PATTERN PLATES ALL PRICING SUBJECT TO GST STEEL NAME PLATES - MACK SELECTION 1230 MACK - AIR TANK - 152mmX76mm. Bin 1228 $ MACK - DRAIN AIR TANKS DAILY - 70mmX40mm. Bin 1228 $ MACK - DRAIN AIR TANKS DAILY - 125mmX66mm. Bin 1216 $ SPRING BRAKE CYLINDER 1228 MACK - MANUFACTURED BY WAGNER ELECTRIC CORP - 60X40mm. Bin 1228 $ CHASSIS 1224 MACK - DO NOT WELD CHASSIS OR DRILL FLANGE - 70mmX50mm. Bin 1216 $ MACK - DO NOT WELD CHASSIS OR DRILL FLANGE - 125mmX66mm. Bin 1216 $ BLANK VIN DOOR PLATES FOR CHASSIS, MODEL, SERIAL NO etc. 152X76mm 1242 MACK TRUCKS INC - PLAINFIELD N.J. U.S.A mmX76mm. Bin 1242 $ MACK TRUCKS Inc - NEW YORK - 152x76mm. Bin 1242 $ FUEL TANK 1234 Mack fuel tank ID information plate. B & early R. Bin 1234 $ R MODEL ENGINE PLATES 1232 Mack engine exhaust emission control information rocker cover plate. 200mm long x 70mm high. Bin $ SECTION 6I - ENGINE PLATES 73

77 6I - STEEL INSTRUCTION & PATTERN PLATES ALL PRICING SUBJECT TO GST R MODEL FIREWALL PLATE 1235 R Model firewall ID plate 90x90. Bin 1234 $ R Model Firewall ID plate 90x90 with MSR ratin. Bin 1235 $ TURNTABLE 1239 TURNTABLE PLATE BLANK - MACK TRUCKS Inc. PLAINFIELD N,.J. U.S.A. - Type/Year. 130x40mm. Bin 1234 $ STEEL ROUND & OVAL SMALL MACK SCRIPT PLATES 1245 MACK - small round steel printed script - fits axle cap & can be used in steering wheel centre - 60mm diam. Bin 1242 $ MACK - OVAL SCRIPT - 60X37. Note: oval section not cut out or drilled. Bin 1252 $ CUSTOM ENGINE PLATES - MADE TO ORDER 1256 MACK THERMODYNE V8 DIESEL ENGINE MODEL END mmX40mm. Bin 1252 $ STEEL PRINTED PLATES GENERAL (cont) 1287 Original 2 speed Electric Shift Plate - generally fitted behind sunvisor - 250x66mm. Suit all makes with 2 speed electric change Eaton Diff. Bin Also available in vinyl sticker. Part No 1287 DASH PLATES 1248 DASH PLATE - CAUTION ENGINE OPERATING RANGE 95x40mm. Bin 1248 $ $ SECTION 6I - ENGINE PLATES 74

78 6I - STEEL INSTRUCTION & PATTERN PLATES ALL PRICING SUBJECT TO GST TRUCK PROTECTION TRUCK ID CONTROL 1247 Truck Tractor Brake control lever plate with Mack logo normal emergency - cut out and made lever slot. Bin 1242 $ POWER DIVIDER ID CONTROL PLATE 1249 Power divider Dry or Slippery Road ID control plate with steel backing and logo. Bin 1248 $ AIR SUSPENSION 1217 Air suspension - Normal or Deflate ID plate with steel backing and logo. $ TRAILER AIR SUPPLY 1218 Trailer Air Supply ON/OFF ID plate. $ POWER DIVIDER CONTROL PLATE 1252 Power divider IN/OUT ID plate with steel backing and logo. - option Bin 1252 $ SPRING BRAKE ID PLATE 1251 Spring brake ID plate. Up Down Lever. Type with lock. Bin 1248 $ ENGINE BRAKE PLATE 1250 Engine Brake ID Plate. Bin 1248 $ NAME PLATE SERVICE. - IF YOU HAVE CHANGED THE SPECIFICATIONS OF YOUR TRUCK OR TRAILER, WE CAN MAKE A NEW PLATE TO SHOW THESE CHANGES. CUMMINS ENGINE ID STEEL PLATE 1271 Cummins original early type engine ID plates - 220mm (81/4 ins) length x 38mm (1 1/2 ins) width. Steel fits on timing gear cover. Bin 1271 $ SECTION 6I - ENGINE PLATES 75

79 6I - STEEL INSTRUCTION & PATTERN PLATES ALL PRICING SUBJECT TO GST DO NOT OVERTAKE 1277 DO NOT OVERTAKE TURNING VEHICLE Steel Sign 400x400. Bin 1277 $ GENERAL ID PLATES - MIXED. Bin 1234 SECTION 6I - ENGINE PLATES 76

80 6I - STEEL INSTRUCTION & PATTERN PLATES ALL PRICING SUBJECT TO GST DIAMOND T 1761 Diamond T standard door chassis ID plate - 95x85mm $ Diamond T General Information under dash Plate - 162x90mm. Bin 1761 $ Original 2 speed Electric Shift Plate - generally fitted behind sunvisor - 250x66mm Bin 1307 $ Brisken Original Greg Style Fuel Tank ID Plate - suit Diamond T 630. Bin 1761 $ ID PLATE - INTERNATIONAL 1318 Cab ID & Specification plate - suit most models built in Australia including R190, R200 $ ID PLATE - WHITE TRUCK 1307 Cab ID & specification plate. Note: top not cut out. 130 high x 110 wide. Bin $ SECTION 6I - ENGINE PLATES 77

81 6J - STICKERS ALL PRICING SUBJECT TO GST CUSTOM CUSTOMER LOGO 1258 Horn button custom built logo. Supplied with your details on stainless steel mounting plate to stick into own horn button. REAR WINDOW SHADOW DOG LOGO 1254R Right Hand Shadow Dog Logo. 200mm long. Has sticky on rear. $ L Left hand Shadow dog - 200m long,. Has sticky on rear. $ AIR CLEANER - B MODEL 1266 Donaldson air cleaner - black striker with white writing. Mack logo with B model ID - 134x49mm $ 2.30 AIR CLEANER SERVICE INSTRUCTIONS - R MODEL 1276 AIR CLEANER SERVICE INSTRUCTIONS for EBA15 as fitted to Superliner and other models. 180mmx145 $ AIR CLEANER ELEMENT - R MODEL 1278 AIR CLEANER ELEMENT INFORMATION sticker. Length 120mmx70mm $ GENERAL MACK AIR CONDITIONING 1282 CASTROL COOLANT - ADD ONLY PREMIUM 50. CHANGE EVERY 4 YEARS. DO NOT MIX - with Mack logo $ 0.45 COOLING SYSTEM 1263 CAUTION: COOLING SYSTEM FITTED WITH FLEETGUARD PG PLUS - with Mack logo - 66x48 $ 0.45 FRAME 1264 HEAT TREATED FRAME - DO NOT WELD OR DRILL HOLES IN UPPER OR LOWER FLANGES with Mack logo. 66x43mm $ 0.45 POWER STEERING 1262 POWER STEERING FITTED WITH DEXRON OIL ONLY- with Mack logo - 66x48mm $ 0.45 SECTION 6J - STICKERS 78

82 6J - STICKERS ALL PRICING SUBJECT TO GST CHANGE AIR CLAMPS 1268 MAINTAIN CHANGE AIR CLAMPS AT 7.3Nm (65lbs) - with Mack logo 66x48mm $ 0.45 ENGINE OIL 1261 USE ONLY MACK APPROVED ENGINE OIL - with Mack logo - 66x48mm $ 0.45 FAN 1269 ATTENTION: MAINTAIN EQUAL CLEARANCE AROUND FAN AFTER ADJUSTING BELTS. THE BELT SURROUND MAY REQUIRE ADJUSTMENT. With Mack logo - 66x48mm $ AUTOMATIC FAN - KEEP HAND FREE with Mack logo - 66x48mm $ 0.45 NOTE: WE CAN MAKE WITH OTHER LOGO ON REQUEST. MACK SCRIPT VINYL LETTERING 1265 Mack lettering cut out to the size of the AB type cross member plate, ALSO suit Bumper Bars, Cross Members, Tanks, Steps, Rear Windows etc 300x90. We also offer a cast one - see Cast Parts in this section. $ MACK - " I WISH I WAS A MACK TRUCK" $ WEE MACK PEDAL CAR LOGO (Note size) 1297 Steel craft pedal car gauges- small 40x25mm. Large - 50x30mm $ Mack scroll logo for pedal car. 200x65mm $ AC Mack pedal car hood logo. 100mm diam $ AC Mack pedal car side logo. 80mm wide x 65mm high $ 9.10 SECTION 6J - STICKERS 79

83 6J - STICKERS ALL PRICING SUBJECT TO GST VINYL STICKERS - GENERAL 2 GEAR SHIFT PLATE 1287 Original 2 speed Electric Shift Plate - generally fitted behind sunvisor - $ x66mm. Suits trucks with Eaton 2 speed electric shift. CATERPILLAR 1308 Caterpillar - 300mm long $ Caterpillar - 300mm long $ Caterpillar 380 long $ INTERNATIONAL 5053 International logo 80mm high $ International logo mm high $ "IF IT'S NOT RED LEAVE IT IN THE SHED" long $ CUMMINS 1283 USE ONLY CUMMINS APPROVED ENGINE OIL - 66X48mm $ 9.10 GM DIESEL ENGINE 1292 GM - Jimmy Diesel. Black, red & white early man with pen and paper cutting operating costs. 120x100mm $ SECTION 6J - STICKERS 80

84 6J - STICKERS ALL PRICING SUBJECT TO GST VINYL STICKERS - GENERAL GM DETROIT 1305 Detroit Diesel red, yellow & black - 80mm square $ Detroit Diesel Power, red, yellow & black. - 80mm square $ GM side bonnett (hood) plate 200mm long mounted on aluminium backing for mounting. Price per each. $ SAFETY 1284 BE CAREFUL - 40long x 120 high $ WARNING - HOT AND HAZARDOUS EXHAUST - 80mmx60mm. $ 9.10 CRUSH ZONE 1291 WARNING CRUSH ZONE - KEEP CLEAR $ 9.10 WATER 1304 DRINKING WATER STICKER LONG X 40 HIGH $ 7.25 HISTORY 1296 PRESERVE OUR HISTORY 30 high x 300 wide $ EUCLID 1286 Round 200mm diam original sticker with pioneer man pointing to the right $ TRAVEL 1303 GONE NORTH A'DROVING long x 190 high $ SECTION 6J - STICKERS 81

85 6J - STICKERS ALL PRICING SUBJECT TO GST VINYL STICKERS - GENERAL PETROL & OIL STICKERS 1259 Kangaroo - small wide x 160 high 1260 Kangaroo - large 440 wide x 350 high R SERIES MACK 1236 WARNING TOWING $ COMPOUND TRANSFER CASE - 120x60 $ MAXIDYNE OPERATING INSTRUCTIONS 110x53 $ ` 1244 CAUTION T2090 TRANSMISSION $ STEERING LOCK ADJUST STICKER - 60x30mm $ DOOR ENTRY WARNING sticker. 100x60mm $ HORN COVER LOGO. Rectangular horn cover mirror background 110mm long 55mm high. Wording is 107mm long $ Mack logo 110mm long x 55mm high 1300 Battery Service Warning. Negative Ground System. 100mm x 65mm. $ SECTION 6J - STICKERS 82

86 6J - STICKERS ALL PRICING SUBJECT TO GST VINYL STICKERS - GENERAL GAUGE INDENTIFICATION STICKER 1174 Gauge face sticker for diff 1 or 2. Suit 1 3/4 diam Face $ ENGINE TEMPERATURE 1175 Gauge face sticker for engine temperature. Suit 1 3/4 diam face. TRANSMISSION TEMPERATURE 1176 Gauge facer sticker of Transmission - suit 1 3/4 diam face Set of 4 as above gauge stickers. $ Jacobs Engine Brake JACOBS START & SHUT DOWN 1179 Instructions 200x110 $ SPLITTER SHIFTING INSTRUCTIONS 1180 Shifting Instructions TRDL 1070/TRTxL x120 $ MAXITORQUE SPLITTER TRANSMISSION 1181 Shift Sequence 150x110 $ DYNATARD INSTRUCTIONS 1182 Correct Dynatard Operation Instructions. 75x60 $ WARNING 1183 Auxillary Brake Warning. 40x40 $ Low Water, Oil Pressure, High Water Temperature. 40x40 $ SECTION 6J - STICKERS 83

87 6J - STICKERS ALL PRICING SUBJECT TO GST VINYL STICKERS - GENERAL STARTING INSTRUCTIONS 1185 Starting Cold Engine. 150x100. $ PIPING SCHEMATIC 1186 Dual Circuit Air Brake System Color Coded Master. $ SECTION 6J - STICKERS 84