TYLDEN HERITAGE R MODEL MACK MAIL ORDER PARTS CATALOGUE

Transcription

1 Catalogue Part No Mack LTL Diesel TYLDEN HERITAGE R MODEL MACK MAIL ORDER PARTS CATALOGUE Custom Classic Truck & Tractor Restorations Business Hours: Location: 1906 Trentham Road, Kyneton Vic 3444 Australia Note: Our workshop & warehouse are only open by appointment Postal Address: P.O. Box 614, Kyneton Vic 3444 Australia Supplier of after market Mack reproduction and dress up parts Big range of Mack B & R Model bits. Special Interest in: Mack Trucks...Diamond T Trucks...Caterpillar Tractors Trading since tyldenheritage@bigpond.com web: Lee No 3 Pty Ltd A.C.N A.B.N These pages may only be reproduced after obtaining written permission from Tylden Heritage. All rights reserved. COST PER PRINTED CATALOGUE INCL POSTAGE 10

2

3 INDEX FOR R MACK PARTS 1R. AXLE: Section 1 CHASSIS: ENGINE: Section 1. Bumper, Fuel Tank, Mudflaps, Steering, Tail Shaft. Section 1: Radiator, Starter Motor. 2R BONNET Section 2: Latches, JEWELLERY: Dogs, Emblems. 3R CABIN INTERIOR: Section 3. 4R CABIN EXTERIOR: Section 4. 5R DOOR PARTS: Section 5. SEE GENERAL SECTION CATALOGUE FOR OTHER PART OPTIONS - Parts for Axle, Brakes, Catches, Dress Up, Electrical, Parts Books, Rubber Parts, Reproduction Cast Parts, Steel Name Plates & Instruction Plates & Stickers.

4 SECTION R SERIES MACK PARTS E9 MOTOR - 2 AVAILABLE Mack E9-450 complete motor. Governed at 1800RPM. 4 Valve Serial No SK0280. Built new 1/3/85. Clutch CL available. Came out of Canada on trailer stock crate. 15, SPEED GEAR BOX - EX ABOVE Mack TRTXL 1070B 12 speed gear box. Serial No. 5K0892 5, REAR AXLE COMPLETE ASSEMBLY Rear axle air bag Mack SA38C Carrier CRDPC92 CRD93 Ratio Brackets for Neway Air Suspension. 6, NOTE: ABOVE PARTS BUILT The above parts came from a Superliner 11 to give truck a required speed of 75 mph = 120Km per hour at 1800 rpm. R CABINS - PAINT STRIPPED R Model cabin, hand stripped back to gal finish - no rust. Ready for painting inside and out. 6, R CABIN COMPLETE - WHITE R Model cabin complete as lifted out of classic. Very good condition and would not require painting if used for work truck. 8, NEW MACK BUMPERS Suit new Superliner, Titan bumper, complete mounting kit with front under protection. (FUP). 1, R MODEL FIBREGLASS BONNET R Model fibreglass bonnet. Does not include grille EARLY 'R' DOOR - LIKE NEW Early door, complete with early type door lock & window winder. Ex USA fire trucks. 1, R MODEL-1 AXLE 1

5 SECTION R SERIES MACK PARTS CHASSIS/AXLE PARTS TIE RODS 402 B Mack tie rod, suit FA 508, FA 517 and some early R Macks. Larger capacity has flat end caps screw in male thread ends Lor R - used RH 1 1/8 x 12 TPI - NEW LH 1 1/8 x 16 TPI - NEW DRAG LINK COVERS 303 B Model Drag link leather grease covers with lace - new R MODEL DIFF 400 Single axle diff hub to hub ex R model - ratio 4.25 with springs. 2, AXLE HUB - MODERN CONVERSION 2947 Axle wheel hubs for conversion to 10 stud USA from Spider. Suit 44000lbs diff. Made in USA. NEW. Price Per Each. Mack Part No MK3398HR735K Brake drum for NEW. Price Per Each CENTRE BEARING 2969 R Bearing 1060mm Top to Bottom 240mm BUMPER BAR 3055 R Model standard bumper bar - black. New. Made in USA POA 3056 R Model standard bumper bar - chrome. New. Weight 25kg. Length 2450mm, height 450mm. Flanges are 90mm. 1, BUMPS STOP SPRING 2819 Front spring buffer, suit R, flat top 2 1/4 high, 2 1/8 diam, 3/4 long X 3/8 locating bolt...see Rubber Parts General Section 6G-6 for pricing and options R MODEL-1 AXLE 2

6 SECTION R SERIES MACK PARTS CHASSIS PARTS BATTERY BOX COMPLETE 3064 Heavy duty Mack battery box base with ribbed top - 2 sections. New. Note: we can supply lid chrome plated Heavy duty Mack type battery box, bottom section holds 2 batteries with rubber latch/catch- as on R model - new. Note: we can supply chrome catch for B Model Black steel ribbed top battery box lid cover - correct for R model - NEW. Note: we can supply lid chrome plated Disassemble chrome plate and reassemble battery box lid (box not included) Steel battery hold down bracket, hold the batteries securely - not stocked Nickel Cadium carriage bolt. Holds batteries bracket down - 2 required (sold as a kit)- not stocked Battery Box Rubber Latch. Mack Supply ELEPHANT SPRING INSULATOR FEET 2754 Top insulator, suit Required. Price Per Each. SEE RUBBER PARTS IN GENERAL SECTION 6G-19 FOR PRICING Top insulator suit steel base, 6ins x 4 1/2 ins 1 3/4 dowl. 4 Required. Price Per Each. SEE RUBBER PARTS IN GENERAL SECTION 6G-19 FOR PRICING 2757 Lower insulator. Suit & rear end. Steel Base 6 1/8 x 6 1/8 1 3/4 dowl. 4 Required. Price Per Each.SEE RUBBER PARTS IN GENERAL SECTION 6G-19 FOR PRICING Side spacer of lower insulator Neoprene. 8 Required. Price Per Each. SEE RUBBER PARTS IN GENERAL SECTION 6G-19 FOR PRICING. MUD FLAPS 3086 Mack facing dog. SEE RUBBER PARTS IN GENERAL SECTION 6G-18 FOR PRICING AND OPTIONS. R MODEL-1 AXLE 3

7 SECTION R SERIES MACK PARTS FUEL TANK 3022 Fuel Cap - Aluminium - small R FUEL CAP GASKET 3020 Cork Fuel cap gasket - 4 1/2 inch OD (114mm) 3 3/4 inch ID (96mm). PRICE PER EACH Fuel Cap - Large FUEL CAP STEP FOR STEP TANK 3025 Step Tank mm long Step Tank mm long R MODEL FUEL TANK FLAT STRAP 3084 R Mack flat fuel tank strap. 2 1/8 wide 1/8 thick (has no edge turn up). Sold Per Foot. SEE GENERAL SECTION 6G- 20 FOR PRICING & OPTIONS FUEL TANK J BRACKET ROLLED EDGE STRAP 3085 Rubber Fuel Tank Strap - 2 inch. Comes in bag of 25ft. (7.6M) SEE RUBBER PARTS IN GENERAL SECTION 6G- 20 FOR PRICING AND OTHER OPTIONS. FRONT FUEL TANK SUPPORT RUBBERS 3434 R fuel tanks per each. 3 3/4 in long x 2 5/8 diam x 1 1/2 hole are split for fitting. SEE GENERAL SECION 6G-20 FOR PRICING & OPTIONS. STEERING PARTS - SHAFTS - BEARINGS 3095 R Bearing Steering Shaft. Size shaft 1 inch OD 2 inch. Bin R Bearing Steering Shaft Firewall. Size shaft 1 inch hole, centres 3 1/2 inch DUST COVER 3097 R Rubber dust boot steering shaft 1 inch (25mm) round hole. See Rubber Parts in General Section 6G-5 for pricing and options. Bin R Rubber dust boot slip yoke 4 slots to suit shaft. See General Section 6G-5 for pricing & options. Bin R MODEL-1 AXLE 4

8 SECTION R SERIES MACK PARTS SHAFT 3091 Shaft steering lower - suit Superliner 2 and other models Shaft steering main - suit Superliner 2 over all length 46 inches (1070mm) as in photo thats with 6 inch (150mm) inside yoke R STEERING YOKE 3088 Yoke. Steering Shaft Ross Box. (.875 inch ID). Bin Universal Steering Top Bin Universal Steering Lower. Note: There are 2 types of Lower Unies. Bin R MODEL-1 AXLE 5

9 SECTION R SERIES MACK PARTS AIR INTAKE FITTINGS 2739 Air Hose hump connector, straight, suit 5 inch tube. Suit Superliner. SEE GENERAL RUBBER SECTION 6G-16 FOR COST & OPTIONS 2742 Air hose connector, straight, suit 6 inch tube. SEE GENERAL RUBBER SECTION 6G-16 FOR COST & OPTIONS 2740 Air elbow 38 deg. Suit 5 inch tube. SEE GENERAL RUBBERS SECTION 6G-16 FOR COST & OPTIONS 2743 Air elbow 38deg. Suit 6inch tube. Suit Superliner. SEE GENERAL RUBBER SECTION 6G-16 FOR COST & OPTIONS 2741 Air elbow 90 deg suit 5 inch tube. SEE GENERAL RUBBER SECTION 6G-16 FOR COST & OPTIONS 2744 Air elbow 90 deg suit 6 inch tube. SEE GENERAL RUBBER SECTION 6G-16 FOR COST & OPTIONS INTERCOOLER CLAMP 1866 Spring loaded inter cooler clamps - 5 inch. SEE GENERAL SECTION 6C-2 FOR COST & OPTIONS 1867 Spring loaded inter coller clamp - 6 inch. SEE GENERAL SECTION 6C-2 FOR COST & OPTIONS AIR CLEANER SEALING GASKET - SEE CAB EXTERIOR. AIR STARTER 3169 Air starter motor used. Note: Pinion lengths vary Air starter valve remote valve assembly. NEW V air starter solonoid control valve - to suit NEW R MODEL-1 AXLE 6

10 SECTION R SERIES MACK PARTS ENGINE PARTS - 6 CYLINDER WATER PUMP KIT 3106 Suit most 60's & 70's Macks 5/8 shaft. (Note: shaft lengths do vary with number of pulleys and front bearing sizes may vary also) WATER PUMP PARTS E9 V Water Pump Kit - 9 Pieces. NOTE: This kit bushes need reaming after fitting. 10 per set Water pump, complete new unit 1, Water pump seal only, suit above kit suit 3/4 shaft 1 5/8 OD. Suit E9. Bin LUBERFINER 1008 Engine oil filter Luberfiner. Length15 inches (380mm) diameter 7 1/2 inches (190mm). Suit 675 and other similar early build engines OIL FILTER 3124 Engine Oil full flow filter. Spin on E6, E7, E R MODEL-1 AXLE 7

11 SECTION R SERIES MACK PARTS ENGINE R MODEL ENGINE MOUNTING INSULATORS 2745 Mack engine mounting rubber. Fits some Flintstones, R Model, V/Liner, Superliner, Ultraliner, Cruiseliner etc from about 70's to around 1990's where they run 8 rear engine mounts, also used as front engine mount on some models. Note: Very common engine mounts. Size of 2745 & mmx20mmdeep with 50mm wide and 18mm hgh centre. Number depending on model. 8 required for most models. 8 standard mounts. Price per each Top harder rubber yellow dot used on rear top mount. 4 per truck. Price per each RADIATOR MOUNTING INSULATOR 2738 Lower mounting 2 piece insulator V8. PRICE PER EACH Insulator Radiator stay side set of 4 cross tie mounting. Top 43mm, bottom 30mm, height 30mm, Hole 12mm ENGINE ID PLATES 1232 Mack engine exhaust emission control information rocker cover plate. 200mm long x 70mm high. Supplied blank for your detail. See General Section 6I-2 for price & options. MACK GENERAL MODELS ( Photocopy) 1628 Workshop Manual Pages - Early - Covers Models B Includes Mack C.M.B.F.R.U & Flintstone - For Engines END END ENDT ENDT673 & B - END END ENDT 864. Fuel pump, clutch, gear box, drive shaft, diffs, came with our first new R Model Mack in 1976 MACK R WORKSHOP MANUAL (Photocopy) 1629 Workshop Manual - covers R-RD-U & DM models Pages. Chassis, cooling, front axle, steering, springs, & suspension, wheels, brakes, electrical. Cabs. This book came with our first new R model Mack in R MODEL-1 AXLE 8

12 SECTION R SERIES MACK PARTS ENGINE - E9 E9 ENGINE PARTS SUBJECT TO STOCK AND AVAILABILITY. PRICE SHOWN ARE AN INDICATION ONLY. E 9 SLEEVE - ALL TO 610HP 3127 Standard engine sleeve - Price Per Each SLEEVE O RINGS PLEASE NOTE DIFFERENCE. TYPE OF O RINGS 447gc USE ORANGE DOT, U TO 5H ENGINES BUILT LATE 70'S TO EARLY 80'S - 447gc 225 USE WHITE DOT. E 9 PISTON 3130 Piston with CV pin Price Per Each E 9 RING SET 3131 Ring Set 400 & 610HP. Price Per Cylinder E 9 BEARING ROD 3128 Bearing Rod Std size. Price Per Cylinder E 9 INLET VALVE 3125 Valve inlet in. 400 to 610HP. Price Per Each E 9 EXHAUST VALVE 3126 Valve exhaust in. 400 to 610HP. Price Per Each E 9 CONROD BOLT E9 865 & Bolt conrod 3/8-18 x Price Per Each R MODEL-1 AXLE 9

13 SECTION R SERIES MACK PARTS E9 ENGINE PARTS (CONT) 3242 Head Gasket. Price Per Each E 9 AIR WATER GASKET 3241 Air and Water Gasket, Price Per Each E9 V8 EXHAUST GASKET 3233 Gasket Exhaust E9. 3.5/8 bolt. Centres 21/2 x 2 1/2 hole. 10 Per Set..PER EACH Oil Ring Turbo Oil Drain Gasket Ring Exhaust - PER EACH Oil Drain Gasket 1 inch hole. 2 1/16 bolt holes Turbo gasket Oil Drain Gasket. 1/2 inch hole. 1 1/2 inch bolt holes E9 TAPPET GASKET 3239 Tappet gasket - SUIT E9. price per each E 9 SUMP GASKET 3240 E9 Sump Gasket R MODEL-1 AXLE 10

14 R MODEL - SECTION 2 BONNETT, JEWELLERY, LATCHES BONNET LATCH SHORT TYPE - STEEL BONNET 3290 R Model black hood latch with square body - New - 4 required per truck - Note: bottom pin needs turning for some models - sold per each - catch is extra. Square tube section 3 1/2 inch x 90mm long BLACK LATCH 3291 R Model black hood catch for above NEW Price Per Each. Bin OPTIONAL CHROME- SHORT TYPE 3292 Model R chrome hood latch with square body - new. Sold per each. Note: Catch is extra. Square tube section 3 1/2 inch x 90mm long CHROME CATCH 3293 Model R chrome hood catch for above - new. Suit Bin STEEL CATCH 3294 Model R hood latch socket - NEW not painted. Bin USED BLACK LATCH SHORT TYPE 3295 Used R Model black short square - some rust. Used BONNET LATCH - LONG TYPE - FIBREGLASS BONNET 3296 Latch - R model chrome fibreglass hood (bonnet) 8 inch (200mm) pin centres with adjustable length. Suit Superliner 11 & Valveliner. Sold Per Each Latch - R Model black fibreglass hood (bonnet) 8inch (200mm) pin centres. 2 Per Truck. Sold per Each. Square tube section 5 1/2 inch x 140mm long BONNET LATCH SPRING - SHORT TYPE 161 Replacement spring bonnet latch. 80mm long x 13mm wide - Bin BONNET LATCH RUBBER 3302 Long bonnet latch. Suit Superliner 2 and others. Length centre of mounting pin to latch connecting point - 7 inch x 180mm overall length 330mm x 13 inch R MODEL - 2 BONNET ETC 11

15 R MODEL - SECTION 2 BONNETT, JEWELLERY, LATCHES SOCKET CLIP FOR Clip for long rubber bonnet latch. Part No As fitted to Superliner and Valveliner. PRICE PER EACH. See Bin Short bonnet latch. Also suit battery box and some bonnets. PER EACH. Length centre of mounting pin to latch connecting point 4 3/4 inch x 125mm SOCKET CLIP FOR Clip for short bonnet hatch. Bin Lower mounting kit for 3301 Bolt not included. Bin BONNET WEAR STRAP 3300 Nylon cabin to hood wear strap. R Model. PER EACH BONNET HINGE 3268 Bonnet hinge ball type Nut 11/16, 18 thread per inch, to suit above.bin Bonnet hinge pivot ball type. Suits R Model bonnet mount (with front radiator mtg intercooler). Bin R BONNET LOCATING ROLLERS 3298 Bonnet locating rollers. 3 inch diam 2 3/8 wide, 5/8 hole. PRICE PER EACH BONNET FLARES 3273 R Model bonnet mudguard flares... Per Set Valveliner v8. Note: 6 cyl flares are different Superliner NOTE: NOT ALWAYS STOCKED, FREIGHT FROM MANUFACTURER TO US NOT INCLUDED - EXTRA BONNET BADGES GRILLE FRONT LETTER SET - R MODEL 3310 Mack letter set. Front. Suit R Bonnet (hood). NEW. Letter size- 5 1/2inch high by 3 1/4 inch R MODEL - 2 BONNET ETC 12

16 R MODEL - SECTION 2 BONNETT, JEWELLERY, LATCHES, DOGS etc CABIN FRONT LETTER SET - F MODEL 3312 Mack F letter set. Front of cabin. New. Letter size 2 inch high SIDE SCRIPT 3311 Mack script name - side 9inch x 3 inch. NEW. Sold Per Each BONNET BADGES 3318 Econodyne Emblem - suit R Model - Price Per Each. Bin Maxidyne Emblem - suit R Model - not stocked POA 3321 Super liner emblem. Price per Each. NEW HALF DOG 3322 Mack R - Half Dog - 2 per truck. L&R hand...new. Price Per Each LATE MACK HALF DOG 3270 New Mack logo standing half dog. Left and Right, facing each other. Cast from brass, detailed and chrome plated. PRICE PER SET OF 2 DOGS MACK LETTER SET 3271 New Mack logo letters. Set of 4, cast from brass, detailed and chrome plated. Price per Set of 8 letters. Bin EARLY MACK DOG 654A New old stock Mack long ear dogs, as fitted to Mack trucks 1932 to LATE MACK DOG 3307 Late Mack Short Eared Dog. Standard bonnet size...new DOG BASE 3308 R Model base for Bulldog - chromed with special screws.new R MODEL - 2 BONNET ETC 13

17 R MODEL - SECTION 2 BONNETT, JEWELLERY, LATCHES, DOGS etc REPRODUCTION MODEL BADGES 3324 Mack R600 badge.cast from Brass, Detailed & Chromed - length 210mm (8 1/4 inch) Mack R700 Badge, Cast from Brass, Detailed & Chromed. Length 210mm (8 1/4 inch) Mack F700 Badge. Cast from Brass, Detailed & Chromed. Length 210mm (8 1/4 inch) Mack R800 badge. Cast from brass. Detailed & Chromed. Length 210mm (8 1/4 inch) V8 Side Badge. Cast from Brass. Detailed & Chromed. 90mmx60x8 thick. Bin BONNET BADGES GRILLE 3303 Grille - Suit R & F - New or Used and Reconditioned. Price subject to quality & stock. Priced on condition. Exchange Service Available. FROM 1000 FIBREGLASS GRILLE MOUNTING 3304 New fibreglass mounting surround POA GRILLE MOULDING 3306 Grille surround moulding - black, in 2 sections. POA HEAD LAMP 3313 New Headlamp Assembly 12V.7 inch domed sealed beam. Fits most Macks with single round headlight also other model trucks & cars. Supplied with lens body and lead ready for fitting. See General Section 6E for pricing As Above but with Halogen 7 inch domed sealed beam Headlamp Gasket for 3313 light assembly Chrome head light bezel. Suits steel style fronts, R also DM, Valueliner and Flintstone & B80 & 81 Tylden JR ute. Size rear ID 210mm front ID. 185mmx30mm deep. Sold Per each Sealed Beam 7 inch holding ring R MODEL - 2 BONNET ETC 14

18 R MODEL - SECTION 2 BONNETT, JEWELLERY, LATCHES, DOGS etc 3316 Headlight Trim. New Stainless steel 16 5/8 long x 9 1/4 high. 7 3/8 inch hole. Price Per Each. NOTE: This type has only 2 bolt holes and is a wee bit smaller than the 6 bolt hole one HEADLIGHT BEZEL - SUPERLINER 3332 Duel headlight bezel. Suit Superliner. 1 3/4 (45mm) deep with mounting screws. PRICE PER EACH Dual headlight bezel Mack Supply. Suit Superliner. 1 3/8 (35mm) with mounting screws PRICE PER EACH HEADLIGHT ASSEMBLY 3338 Complete oblong head light assembly RH (see part no 3332 for chrome bezel) Complete oblong head light assembly LH. (see part no 3332 for chrome bezel) ROUND BLINKER (INDICATOR) LIGHTS 769 Fender (mudguard) turn signal round face look a like 100mm light with chrome bezel - amber both sides - suits B & R model & other US built trucks - SOLD PER EACH SEE GENERAL 6E-1 FOR PRICING & OTHER OPTIONS R TYPE SQUARE BLINKER 3334 R Model double side square LED hood top mounting blinker lamp includes wiring tail. NOTE: This light has built in side lamp so 3335 below would not be necessary. SEE GENERAL 6E-1 FOR PRICING & OTHER OPTIONS SUPERLINER STYLED DUAL FACE BLINKER 3341 Combination turn signal, side marker & park light signal with round lens. USA made, grey body with amber or amber and red main lens. Replaceable globe 12V 2.1A 0.5 minor. 4 wires. Price Per Each. SEE GENERAL 6E FOR PRICING & OTHER OPTIONS 3261 Blinker mounting wedge ROUND BLINKER SIDE AMBER 3335 R Model side hood blinker lamp assembly. - Amber with wiring. SEE GENERAL 6E-1 FOR PRICING & OTHER OPTIONS. PARK LIGHTS 3336 Lamp Marker Park Light Assembly, clear with wiring. See General Section 6E-7 for Pricing Parking light lens only - clear or amber for above & See General Section 6E-7 for Pricing and options. R MODEL - 2 BONNET ETC 15

19 R MODEL - SECTION 2 BONNETT, JEWELLERY, LATCHES, DOGS etc FRONT MUDFLAP 3340.Mudflap bonnet LH & RH R Model black with brass eyelets, not Valveliner. See Rubber Parts in General Section 6G-18 for pricing and options. BONNET (HOOD) WEBBING 2692 Suit Flintstone etc. - See Rubber in General Section 6G-4 for Pricing and Options. BONNET & SLEEPER MOUNTING RUBBERS 2746 Bonnet pivot mounting insulators. Supplied with 2 large lower & 2 small upper. Note: this part fits some R, V/Liner, S/Liner & early Titans and cab and sleeper box mounts as well. Size 65x30 with 52x13 top. See Section 6G-3 for pricing Lower bonnet mount size 52mmx13. See Rubber in General Section 6G-3 for pricing and options. R MODEL - 2 BONNET ETC 16

20 R MODEL - SECTION 3 - CABIN INTERIOR WESTERN TRIM 3345 Tylden offer a full R Model Western Trim package as per factory with large facing dogs or diamonds hot welded into material or optional stitched with loose buttons. Available in brown, cream, grey, magnum (red), or colour of your choice. Western Trim including 2 seats (part No 3347), 2 Door trims (Part No 3348), Rear Cab (Part No 3349) and Hood Lining (Part No 3350). 2 Pillar Trims. NOTE: ALL PRICES SHOWN ARE FOR UPHOLSTERY ONLY Bucket Seat Cushion, original perforated vinyl with Mack Logo stamp (as original) IN BACK. Price Per Each. Ask us to better photos. 2, R Model Western door trim with welded dog logo. Original welded patterns or stitched with buttons. Price Per Each. Ask us to better photos R Model door arm rest, included with 3348 OR Price Per Set. Ask us to better photos R Model rear Cab lining Western original pattern in perforated vinyl. Ask us to better quality photos R Model roof head lining in perforated vinyl. Ask us to better quality photos Head lining holding buttons. Supplied black but can be painted. Price Per Each. Bin FOLLOWING NOT INCLUDED IN PART NO PACKAGE ABOVE PRICES ROOF CONSOLE TRIM 3351 R Model front roof console. Cover Only. (console supplied by customer) Length 1400x250x New R front roof console with corner pieces made from aluminium. See above for cover. FLOOR CONSOLE COMPLETE 3352 R Model centre floor console in vinyl, base & lid. - trim only. Box supplied by Customer ALL NEW FLOOR CONSOLE 3357 Complete new centre console, 390mm long x 300mm deep x 280mm wide, folded from steel with hinged marine ply. Lid covered in vinyl with stamped dog logo in lid. Interior covered with light carpet Steel centre console base only, 390mm x300mm deep x 280 wide Gear Stick boots with Mack letters embroidery. Price Per Each. Ask us to better photo R MODEL-3 CABIN INTERIOR 17

21 R MODEL - SECTION 3 - CABIN INTERIOR CABIN SIDE INFILL 3358 Cabin side kick infill same colour of interior HATCH SURROUND 3353 R Model hatch surround. Cover Only New inner R hatch ventilator surround made from steel to shape of original plastic (Not Covered) DOOR PILLAR 3354 R Model Side front pillar trims - L & R at top of photo. Centre of photo shows door arm rests - part Bottom photo are angles to hold roof console part Note: 3356 & 3351 are display only. DOG STAMP 3365 Stamp your material with original dog type stamp PRICE PER EACH INTERIOR LIGHT 3364 R Model dome interior light with switch and lead DASH PANEL LH 3410 New R model genuine dash - left hand section. Including top hatch. 1, GLOVE BOX LID 3413 New glove box lid to suit above DASH PANEL RH 3411 New R model genuine dash - right hand section DASH PANEL SCREW 3516 Dash Panel Screw. See door for nut. Bin R MODEL-3 CABIN INTERIOR 18

22 R MODEL - SECTION 3 - CABIN INTERIOR DASH PANEL RH 3363 New R top ashtray DASH NUT 2591 Nut - dash and door trim speed nut. Price per Each. Bin DASH PLUG 2924 Plug, snap lock & HLE suit 1/2 inch hole in dash panel ENGINE STOP CABLE 3359 R Model engine stop cable. Red Knob HAND TROTTLE CABLE 3360 R Model hand throttle cable. Black knob R MODEL-3 CABIN INTERIOR 19

23 R MODEL - SECTION 3 - CABIN INTERIOR STANDARD MATCHING GAUGES SUIT R & B MACK USA SUPPLIED GAUGES SPEEDO 3367 Speedo gauge kmh cable 3 1/4 diam R Model speedo cable with 2 types of adaptors -112 inch Length 3050mm Speedo gear box drive 3 1/2 inches square TACHO 3369 Tacho gauge. Zero to 3200 RPM with built in hour meter. 3 1/4 inch R Model Tacho cable with 3 types of adaptors. 88 inch (2240mm long.) MECHANICAL OIL PRESSURE GAUGE 3372 Oil pressure gauge PSI mechanical. Suit 2 inch hole mounting LOW OIL PRESSURE SWITCH 3373 Low oil pressure warning engine switch OIL TEMPERATURE GAUGE 3378 Mack Gauge - Oil Temp. Engine, Transmission & Diff. 60 to 160 Cel.Bin Mack Gauge - Oil Temperature Sender for Transmission & Diff. Bin VOLT METER 3377 Mack Gauge Volt 12V 10 to 16amps battery condition and charge section WATER TEMPERATURE GAUGE 3380 Mack Gauge - Water Temp Neg Fahrenheit Mack Gauge - Water Temperture Sender Unit. Negative Ground. Bin R MODEL-3 CABIN INTERIOR 20

24 R MODEL - SECTION 3 - CABIN INTERIOR AIR PRESSURE GUAGE SINGLE NEEDLE 3385 Air pressure gauge single needle 0 to STANDARD USA MATCHING GAUGES - BLACK FACE & BEZEL. SUIT MOST TRUCKS FUEL GAUGE 3387 Fuel Gauge. Note: No stock at present. Option part No 3163 US TYPE FUEL GAUGE SENDER 3388 Sender Fuel Gauge. B, R & F multi volt. Suit tank 6-24 inch deep. Suit Pal & Mack gauges. 250ohm empty 1020ohm half full & 31ohm full. For Stewart Warner, Datcon, Fara, Medallion & Teleflex gauges. Supplied with instructions PYROMETER 3374 Pyrometer gauge - 2inch face Thermocouple - suit MACK TACO 1030 Tachometer head, chrome bezel, black face with Mack logo. 0 to 3200 RPM with engine hours. Cable operated. Suit 85mm diam hole OPTIONAL FITTINGS FOR GAUGES V Light socket to suit gauges. Price Per Each. Note: VDO gauges come with light socket. Bin OIL AND AIR GAUGE FITTING KIT 3371 Oil gauge line and air gauge insulation kit with 2m of 3/16 PVC tube with 1/8 NPT female connector for gauge and 1/8 NPT male end for connection to engine or air system. Cost per Kit R MODEL-3 CABIN INTERIOR 21

25 R MODEL - SECTION 3 - CABIN INTERIOR GAUGES - MACK SUPPLIED - SPEEDO 3155 Speedo head cable operated with in built dipper light 0-120Km. 85mm hole size TACHOGRAPH 3156 Tacho head RPM cable operated with inbuilt hour meter. 85mm hole size Tachometer head, chrome bezel, black face with Mack logo. 0 to 3200 RPM with engine hours. Cable operated. Suit 85mm diam hole. New Old Stock EINGINE OIL PRESSURE 3157 Oil Pressure Gauge. 0 TO 150 OIL TEMPERATURE 3158 Oil Temperature. Engine, Transmission, diff 1 and 2. VOLT METER 3159 Volt Meter ENGINE WATER TEMPERATURE 3160 Water Temperature Gauge 40 to 120. Suit 53mm hole AIR PRESSURE DUAL 3161 Air Pressure - Dual Needle. Dual pipes AIR PRESSURE KIT 3371 Oil and Air line and fitting kit. 2m PVC tubing and gauge adapter. Note: air gauge has 2 connections FUEL GAUGE 3163 Fuel Gauge - Neg grooving. Suit 53mm hole Pyrometer PYROMETER 3165 Boost BOOST R MODEL-3 CABIN INTERIOR 22

26 R MODEL - SECTION 3 - CABIN INTERIOR INDICATOR STALK - TURN SIGNAL 771 R Series indicator stalk - 7 wires. See General Section 6E-1 for pricing and options. 775 R Series indicator stalk. - 8 Wires. See General Section 6E-1 for pricing and options. DIP SWITCH (BELOW FLOOR TYPE) 3389 R Series dip switch with long or short leg. Bin LOCK SET IGNITION & DOOR 856 Lock Kit Ignition and door lock R & F. See General Section 6E- 2 for pricingbin 88 CUSTOM HORN BUTTON LOGO 1258 Custom horn button logo with your Custom details. Mounted on S/S plate for easy mounting on your horn button. See Stickers in General Section for Pricing FRONT FLOOR MAT 3391 R Model front floor mat - moulded rubber ribbed with Mack logo & wear section on LH side. Weight 8 Kg REAR FLOOR MAT 3392 R Model rear floor under seat mat - moulded ribbed rubber. Weight 2.5Kg R Model plain floor mat (no ribs etc) supplied in one section. Approx 700 LOOSE FLOOR MAT 2771 Floor mat - loose with dog logo with cut out for peddles. Sold as Pair. The second (passenger side) one is square R MODEL-3 CABIN INTERIOR 23

27 R MODEL - SECTION 3 - CABIN INTERIOR R MODEL CLUTCH PEDAL 3406 R Model clutch pedal & bracket clutch type. Generally stocked to change from old through floor pedal type to pendulum type with cable. Photo shows insulation in B Model. - Used CLUTCH CABLE 3404 Suit R600 & Valveliner 109" (2770mm) 112" (2850mm) tip to tip Suit Trident, Titan, VL S/L, 138" (3480mm) long GEAR SHIFT BOOT 2869 Gear shift boot - rubber - 180mm long x 100mm wide x 70mm high. See General Section 6G-5 for pricing 2868 Stainless steel surround Cover for boot See General Section Rubber 6G-5 for Pricing Steering Column gear shift boot and rubber - 222mm long x 135mm wide x 70 high.see General Section 6G-5 for pricing CLUTCH RUBBER 2482 Clutch pedal - rubber replacement pad, also fits B Model. See General Section 6G-1 for pricing. R MODEL FOOT VALVE PEDAL 3074 New brake pedal with Mack logo. Note holes are not drilled. See General Section for other brake options THROTTLE PEDAL 361 R Model fuel pedal only with Mack logo - New. Price Per Each KICK PLATES 3415 R Door entry stainless steel kick plates with Mack logo and special clear hard coat. Price Per Each R Model Entry Kick Plate. Custom to fit around corners with printing of your choice. Polished Stainless Steel with special clear hard coat. POA R MODEL-3 CABIN INTERIOR 24

28 R MODEL - SECTION 3 - CABIN INTERIOR HEATER DUCT Round heater duct vents - suit R Model 3407 Oblong heater duct vents - suit R Model VINYL STICKERS - GENERAL STEERING WHEEL 3454 Mack optional upgrade. 18 inch 4 spoke steering wheel. See General Section 6D for pricing. POA 3455 Steering wheel hub for above to suit R model standard steering shaft. POA MACK AIR ACTUATORY 3405 Mack red dot part no 4379-RD suit Mack CHR 1992 to about Used to open and close air vent shutters DRIVER INSTRUCTION STICKERS SEE GENERAL SECTION - 6J FOR OPTIONS R SERIES MACK CAB STICKERS 1236 WARNING TOWING. See Stickers General Section 6J-5 for pricing 1237 COMPOUND TRANSFER CASE See Stickers General Section 6-5J for pricing 1241 MAXIDYNE OPERATING INSTRUCTIONS. See Stickers General Section 6J-5 for pricing 1244 CAUTION T2090 TRANSMISSION. See Stickers General Section 6J-5 for pricing ` 1246 STEERING LOCK ADJUST STICKER 60x30mm - SAMPLE PHOTO See Stickers General Section 6J-5 for pricing 1274 DOOR ENTRY WARNING sticker 100x60mm. See General Section 6J-5 for pricing R MODEL-3 CABIN INTERIOR 25

29 SECTION 3 - R MODEL - CABIN 1280 HORN COVER LOGO. Rectangular horn cover 112mm long 56mm deep. Wording is 107mm long. See General Section 6J-5 for pricing GAUGE INDENTIFICATION STICKER 1281 Gauge face sticker for diff 1 & 2 plus gearbox and engine. See General Section 6J for pricing Battery Service Warning. Negative ground system. See General Section 6J for pricing OPERATING INSTRUCTIONS Start & Shut down Instructions 200x SPLITTER SHIFTING INSTRUCTIONS 1180 Shifting Instructions TRDL 1070/TRTxL x MAXITORQUE SPLITTER TRANSMISSION 1181 Shift Sequence 150x DYNATARD INSTRUCTIONS 1182 Correct Dynatard Operation Instructions. 75x WARNING 1183 Auxillary Brake Warning. 40x Low Water, Oil Pressure, High Water Temperature. 40x STARTING INSTRUCTIONS 1185 Starting Cold Engine. 150x PIPING SCHEMATIC STICKER OR HARDBACK 1186 Dual Circuit Air Brake System Color Coded Master. Size 300x200mm. See Section 6J for options and pricing R SWITCH LABELS 1173 Replacement switch labels to stick onto existing backing. HTD Mirrors, Driving Lights, Clips, Panel LPS, Park P. Eng Brake, Lights, Off AM, Roof Warning, others available on request. See 6J Stickers for pricing. R MODEL-3 CABIN INTERIOR 26

30 SECTION 4 - R MODEL CABIN EXTERIOR AIR CLEANER 3460 Used RH Mack air cleaner 15 inch OD (sample photo) (SUBJECT TO STOCK AVAILABLE) POA TOP GASKET 3462 Top Lid Gasket - Suit R and Valveliner. 380 OD. 12 Holes AIR CLEANER TOP HAT NUTS 3190 Nut top of air cleaner. 12 in set. Price per each nut AIR FILTER ELEMENT 3463 Air Cleaner Element - Suit Mack R & Valveliner AIR CLEANER HAT 3461 Air cleaner hat - black plastic 15in x 3 1/2 plus sprigit extra 1 1/2 ins rain. Suit pipe size 6 inch Air ram 6 inch with side vents AIR CLEANER SERVICE INSTRUCTIONS 1276 Air Cleaner Service Instructuion for EBA15 as fitted to Superliner and other models. 180mmx AIR CLEANER ELEMENT INFORMATION 1278 Air Cleaner Element Information Sticker. Length 120mmx70mm AIR INTAKE FITTINGS 2739 Air Hose hump connector, straight, suit 5 inch tube. Suit Superliner. SEE GENERAL RUBBER SECTION 6G-1 FOR COST & OPTIONS 2742 Air hose connector, straight, suit 6 inch tube. SEE GENERAL RUBBER SECTION 6G-16 FOR COST & OPTIONS 2740 Air elbow 38 deg. Suit 5 inch tube. SEE GENERAL RUBBERS SECTION 6G- 16 FOR COST & OPTIONS 2743 Air elbow 38deg. Suit 6inch tube. Suit Superliner. SEE GENERAL RUBBER SECTION 6G-16 FOR COST & OPTIONS R MODEL - 4 CABIN EXTERIOR 27

31 SECTION 4 - R MODEL CABIN EXTERIOR 2741 Air elbow 90 deg suit 5 inch tube. SEE GENERAL RUBBER SECTION 6G-16 FOR COST & OPTIONS 2744 Air elbow 90 deg suit 6 inch tube. SEE GENERAL RUBBER SECTION 6G-16 FOR COST & OPTIONS AIR HORN - ROUND 3439 Horn - Air - round single trumpet kit. Suit R model 600mm (24 inches) long AIR HORN - RECTANGULAR 3440 Mack horn air rectangular - front with snow cover with mounting kit HORN COVER LOGO 1280 Rectangular Horn Cover 115mm long 56mm deep. Wording is 110mm long CABIN INSULATOR 3434 Cab front insulator R cabin. Also R fuel tanks per each. 3 3/4 in long x 2 5/8 diam x 1 1/2 hole are split for fitting CAB ENTRY GRAB HANDLE 3437 Grab entry handles. 23 long. Price Per Each CAB LEVELLING VALVE 3467 Valve cab levelling suit R Model + T401 Kw CABIN SUPER CUSHION AIR BAG 3468 Cabin rear air spring bag. Max inflation 100 PSI. Max Torque 15ft lbs. Length 5 1/4 inch. Diameter at big end - 3 1/2 inch CABIN BULLET LIGHTS 3444 Bullet type roof lights 390mm long x 90mm diam, supplied with mounting bolts. See General Electrical Section 6E for pricing and options Bullet short centre light. 200mm long x 90mm diam. Price Per Each. See General Electrical Section 6E for pricing and options. R MODEL - 4 CABIN EXTERIOR 28

32 SECTION 4 - R MODEL CABIN EXTERIOR ROUND BLINKER (INDICATOR) LIGHTS 772 Fender (mudguard) turn signal round face look a like 100mm light with chrome bezel - amber both sides - suits B & R model & other US built trucks - SOLD PER EACH SEE GENERAL 6E FOR PRICING & OTHER OPTIONS R TYPE SQUARE BLINKER 3334 R Model double side square LED hood top mounting blinker lamp includes wiring tail.. (see Electrical in General Section 6E-1 for pricing). NOTE: This light has built in side lamp so 3335 above would not be necessary. SEE GENERAL 6E FOR PRICING & OTHER OPTIONS SUPERLINER STYLED BLINKER 3341 Combination turn signal, side marker & park light signal. USA made, grey body with amber or amber and red main lens. 4 wires. Price Per Each. Extra 2 Amber lens. SEE GENERAL 6E-1 FOR PRICING & OTHER OPTIONS ROUND BLINKER SIDE AMBER 3335 R Model side hood blinker lamp assembly. - Amber with wiring. SEE GENERAL 6E-1 FOR PRICING & OTHER OPTIONS. CABIN VENTS TOP ROOF VENT 3449 Cabin top roof ventilator cowl outer assembly R MODEL CABIN ROOF VENT SEAL 3420 Roof Vent Seal. 37 INCHES (940mm) SIDE CABIN VENT 3450 Side Vent Cover SIDE CABIN AIR VENT RUBBER 2621 R Model side air vent sealing rubber. 10mmx8mm. 700mm (27 1/2 inches) per vent. SEE SECTION 6G-15 FOR PRICING FRONT VENT OPENER OPTION 901 Optional front vent opener. Can be adapted to suit without a lot of modification. 155mm closed 205mm open. Max load 125kg. Travel speed 6mm per second. Has inbuilt limit switches supplied with 12V switch MIRROR - SEE DOORS NEXT SECTION WINDSCREEN GLASS 3416 Windscreen glass LH, suit R. valve, super, metro. Weight 10 Kg. 31 inches (800mm) x 21 inches (530mm) Windscreen glass RH, suit R, valve, super, metro. Weight dimension as LH R MODEL - 4 CABIN EXTERIOR 29

33 SECTION 4 - R MODEL CABIN EXTERIOR R MODEL FRONT VENT COWL ASSEMBLY 3451 Front cabin vent cowl assembly. CompletE, ready for assemble. (has rod assembly but no control) R MODEL WINDSCREEN RUBBER 3418 Windscreen rubber - complete both sides REAR WINDOW 3430 Suit R & F C/liner & MCR Model rear window - laminated. Tinted Std. Auto glass. Weight 8 Kg. Length 1100mm Height 450mm Rear window glass rubber seal. Supplied with inbuilt lock strip MIRROR SEE DOOR PARTS - NEXT SECTION R MODEL WIPER BLADE 3497 Windscreen wiper blade. R Model. 16 inch long F MODEL WIPER BLADE 3498 Windscreen wiper blade - F Model - 20 inch long (500mm) R MODEL WIPER ARMS 3495 LH wiper arm with inbuilt concealed windshield washer nozzles & two knurled drive options RH Wiper arm with inbuilt concealed windshield washer nozzle and two knurled drive options R MODEL WIPER PIVOT BODY 3490 RH Pivot body and complete connecting arm assembly with end bearing for connection to wiper motor LH Pivot body and complete connecting arm assembly with end bearing for connection to wiper motor AIR WIPER MOTOR 3487 New Air wiper motor assembly. Note: this requires a new valve see below New Valve control assembly for above (3487) air wiper motor. Bin R MODEL - 4 CABIN EXTERIOR 30

34 SECTION 4 - R MODEL CABIN EXTERIOR R MODEL ELECTRIC WIPER MOTOR CONVERSION KIT 3474 Wiper Motor Assembly Etc Link Assy LH- without shaft Linkage Wiper without shaft Screw & Washer (4 required each) Arm wiper elec RH Arm Wiper elec LH Wiper blades - 2 required PRICE PER EACH Breaker Circuit Switch elec W Bolt 1/2 x 1/ Washer Harness Knob Wiper Switch KIT ITEMS AS SHOWN... COST 1,330 R MODEL - 4 CABIN EXTERIOR 31

35 SECTION 4 - R MODEL CABIN EXTERIOR WINDSCREEN BOTTLE 3499 Reservoir windscreen washer bottle cap & pump. 12V. R model door Washer bottle cap only. Bin Plug with wiring harness for windscreen washer bottle. Plus Postage WINDSCREEN BOTTLE PUMP 3494 Washer bottle pump. 12V. Bin STEEL PLATE FIREWALL PLATE 1235 Blank Firewall certification plate (See General Section 6-3I for pricing). FIREWALL ID PLATE - SPECIAL 1233 Blank Firewall centification plate with MSR..See General Section 6 for pricing. Bin 1235 SLEEPER TO CAB SEAL 2639 Universal sleeper seal, an efficient seal designed to connect and seal crawl space between the driving and sleeping cabins in trucks. 6 inches wide. Can close to 5 inches and open to 7 inches wide x 25 deep. Sold per metre. Weight 4m = 1Kg FITTING SEAL Sleeper mounting may be best to mount say 3 inches gap between cab & sleeper, depending on seal mounting location. If cab is on air then sleeper gap would be better at larger gap. FITTING - start at bottom centre and seal and clamp seal around opening back to lower centre. When happy with connection, cut seal for force, fit and seal with rubber glue, Seal is Australian made. R MACK Crawl through opening supply. 3.1 metres including shipping Australia wide Walk through opening with V opening. Supply 4metres including shipment Australia wide R MODEL - 4 CABIN EXTERIOR 32

36 SECTION 5 - R MODEL - DOORS 3500 Door shell - R Model - new Left - suits 79 onwards door locks. Weight 20Kg. Height 1400mm x 860 x Door shell - R Model. New right. Sit 79 onwards door locks Door - R Model - Used. Ask re condition & price. Shell or complete. DOOR INNER PANEL 3506 Door inner panel RH suit late model. Bare - NEW Door inner panel LH suit late model. Bare. New Door panel screws. 20 Required per door. Price Per Each. Bin Door Panel J Nuts - 20 required per door.- 1/4 in thread. Bin DOOR HANDLE 3523 R door handle. Outer R & F model cab R door handle inner R & F pre 79 NOTE: Part no below has better clearance R Model door handle late - inner R & F after 1979 with thicker Western trim R Model door pull handle. Suit R, RB, RD, DM, MC, MR & LE. NO STOCK AVAILABLE AT THIS STAGE R MODEL-5 DOORS 33

37 SECTION 5 - R MODEL - DOORS PLEASE NOTE: DOOR PART CHANGES IN 1979 AND 1983, DOOR HANDLE ESCUTCHEON 3526 Handle escutcheon. Suit door and window crank handle Pin Handle window & door. Suit door and window crank handle. Bin QUARTER VENT WINDOW 3528 Vent window flipper LH. (Quarter Vent), Suit models R & F Vent window flipper RH. (Quarter Vent). Suit models R & F GENUINE MACK SUPPLY 3532 R model vent window flipper (quarter vent). LH only. Bin R model vent window flipper (quarter vent). RH only R Model vent window flipper (quarter vent) outer rubber seal LH only 3572 R Model vent window flipper (quarter vent) outer rubber seal RH only R MODEL DOOR GLASS 3530 Door glass R & L. Note: We supply 6mm green tinted toughened auto glass R MODEL EARLY WINDOW REGULATOR 89 Window regulator scissors - Left. Suit early R style cabs Window regulator scissors - Right. Suit early R style cabs R R MODEL EARLY REGULATOR GEAR PLATE Gear plate for passenger LH side door regulator. Suit early style cabs R Gear plate for driver RH side door regulator. Suit early styled cabs. Even No = R side Door gear plate retaining clip for Part 91 & Per door. PRICE PER EACH. Bin R MODEL-5 DOORS 34

38 SECTION 5 - R MODEL - DOORS EARLY SIDE GLASS SUPPORT CHANNEL PLEASE NOTE: DOOR PART CHANGES IN 1979 AND 1983, EARLY WINDOW SUPPORT 3566 Support channel for door glass regulator for passenger RHside roll up window glass 400mm long. Used with Part 89 & 90. Suit early styled cabs Support channel for door glass regulator for driver side LH roll up window glass 400mm long. Suit early styled cabs DOOR GLASS SETTING CHANNEL & QUARTER VENT GLAZING SEAL - HOLDS GLASS IN PLACE Quarter vent and door glass holding rubber. 400mm per B door, mm per B vent. Softens with kero to help fitting. When dried makes strong bond to glass. Used with door glass channel lifter and quarter vent glass in its frame and some windscreen and glass frames. Sold per metre. 1 1/2 WIDE X 1/16 THICK. (1.5X87MM). SOLD PER METRE. LATE MODEL WINDOW REGULATOR 3538 Regulator assembly LH. (Later model - post 83) Regulator assembly RH. (Later model - post 83) Screw for regulator assembly above. (6mm) 4 Per Door. Price Per Each. Bin Retaining ring for regulator to glass support track. Price Per Each. (Suit 3538 & 3539). One required for late R per door. Two required for early type R per door. Bin Linkage remote door. Connects handle to door lock. Used with part No 3538 & R MODEL-5 DOORS 35

39 SECTION 5 - R MODEL - DOORS PLEASE NOTE: DOOR PART CHANGES IN 1979 AND 1983, LATE MODEL WINDOW SUPPORT 3535 Support window RH model. Used with Part mm long Support window LH model. Used with Part mm long WINDOW REGULATOR HANDLE 3525 Window regulator handle, early R&F. See part no 3526 & 3527 for escutcheon & pin..page 2. Note Part No 3531 below has more clearance. WINDOW REGULATOR HANDLE - LATE 3531 Window regulator handle. Suit doors with Western Trim or worn Shafts DOOR LATCH EARLY TO Latch door early RH, suit R & F, MIR, MBR Latch door - early LH. Suit R & F, MIR, MBR DOOR LATCH AFTER 1979 R & F 3542 Latch door late RH. Used with part no Mack current style DM, R, RB, RD Latch door- late LH. Used with part no Mack current style DM, R, RB, RD DOOR LATCH SCREWS 3517 Door latch holding screws. 3 Per Door - 1/4 inch. PRICE PER EACH... Bin DOOR STRIKER - EARLY R & F 3555 Striker Plate - RH. Mack early style R, RB, RD, DM Striker Plate - LH. Mack early style R, RB, RD, DM Striker Plate RH - used with part no Mack current style R, RB, RD, DM. Screws not included DOOR STRIKER - LATE R & F 3560 Striker Plate LH. used with part no Mack current style R, RB, RD, DM. Screws not included R MODEL-5 DOORS 36

40 SECTION 5 -R MODEL - DOORS KEY DOOR LOCKS 856 Door & ignition lock set, includes 2 door tumblers and one ignition tumbler with 2 matching keys. New. SEE GENERAL SECTION 6E-2 FOR PRICING Bin 88 DOOR LOCK RETAINER CLIP 2912 Door lock slide in retainer clip. Slides from outside inner door to hold door lock in place. - New. Bin 2914 See General Section 6G for pricing. BAILEY CHANNEL - R & F Channel Bailey R&F. 2 per door. Price Per Each. Supplied with 5 clips. See Rubber Parts in General Section 6G for Pricing. Note: For quarter vent flexable, 3549 is OK but rigid looks better. Supply 510mm of 2510 rigid with S/S bead. OPTION Supply 510mm of 2501 rigid with S/S bead WINDOW WEATHER FELT STRIP 3550 Weather strip R & F model RH door glass sqeegee guides.- 1 required per door L & R. Price Per Each.see Rubber Parts in General Section 6G for Pricing Weather strip R&F model LH. Door Glass Sqeegee. See Section 6 G for pricing. WINDOW WEATHER STRIP WITH RUBBER SEAL 3546 Weather strip R&F model door glass squegee guides with rubber wiper seal and door lip curved section to rear - RH (one per door). PRICE PER EACH 3547 Weather strip R&F model door glass squegee guides with rubber wiper seal and door lip curved section to rear - LH (one per door) -PRICE PER EACH SPECIAL DOOR SEAL 3558 Rubber super soft hollow door seal. Adhesive backing. Fits in cabin door, closes against it.. 13mm wide 18mm high, sold in a 4.5m (15ft) length. 18 wide x 19 high. 1 Roll per door MIRROR ARMS 3575 Kit mirror bracket RH stainless Kit mirror bracket LH stainless MIRROR HEAD 3577 Mirror head-mack. LH alloy type with bulldog but no heating or light. See 803 General Electrical Section for light in photo 3578 Mirror head-mack. RH alloy type with bulldog but no heating or light R MODEL-5 DOORS 37