Code 0 Description Pic Link # Used Diameter Thread Pitch Length Washer 1 Washer2 Nut size Class Notes F Alternator bracket mounting bolts

Transcription

1 Code 0 Description Pic Link # Used Diameter Thread Pitch Length Washer 1 Washer2 Nut size Class Notes F Alternator bracket mounting bolts (Engine Lift Hook) split washer flat 4 14mm head if JIS but 17mm fits 15 2 Alternator Mounting Bracket to Block Bolts (1F Engine) split washer flat mm Head 15 3 Bell Housing to Engine Block Bolts split washer 5 17mm head. 19mm will NOT fit! 15 4 Crank Pulley Nut (FJ60) N/A 45 mm head (Crank threads are 25mm long) 15 5 Engine Side Cover to Block bolts (13 of 15) split washer 4 10mm head JIS or DIN 15 6 Engine Side Cover to Block bolts (For Heater Hose Clamps. ) (2 of 15) split washer flat 4 10mm head JIS or DIN 15 7 Motor Mount Bracket (Front) to Isolator Bolts split washer 4 17mm head but 19mm will fit 15 8 Motor Mount Bracket (rear) to Bell Housing Bolts split washer 5 17mm head. 19mm will NOT fit! 15 9 Motor Mounts (front) to Motor Bolts split washer flat 7 10mm shoulder. 14mm head Oil Pan to Block bolts split washer 4 12mm hex AND phillips head. 13mm hex will fit Power Steering Pump to mounting bracket split washer flat(2) 8mm 4 14mm Head Starter Retaining Nut (Fits top Stud in Bell Housing) split washer 17mm N/A Starter to Block bolt split washer flat 17mm head Starter to Block Stud: 1 N/A 27mm long 10mm of 1.75 pitch threads on one side and 15mm of Timing Cover to Block bolts (Long) (2 of 12) split washer 4 10mm head Timing Cover to Block bolts (Lower two Bolts) (2 of 12) mm shoulder. 14mm head Timing Cover to Block bolts (Short) (8 of 12) split washer 4 10mm head Oil Filter bracket to Intake Manifold split washer 4 12mm head if JIS but 13mm fits Oil Pressure Regulator to Block Bolts Captured split 4 12mm head if JIS but 13mm fits Fan Shroud to Radiator U Frame bolts split washer flat Fan/Fan Pulley to Water Pump split washer 4 12mm head if JIS but 13mm head fits Radiator U Frame top Cross member bolts split washer flat Radiator U Frame Welded on studs split washer flat 14mm N/A Radiator U Frame: Small front shroud to Radiator U Frame screws split washer N/A JIS #2 Phillips head Thermostat housing (Lower) to block bolts Captured split 4 14mm head Thermostat housing (Top) to lower housing split washer 4 12mm shoulder. 12mm Head Valve Adjusting Nut mm Note: 4/79 amd later 2F's they went to a 14mm nut! Water Pump to Block (F Engine ) (1 of 5) split washer 5 35mm shoulder. 14mm head Water Pump to Block (F Engine) (4 of 5) split washer 5 10mm Shoulder. 14mm head Carb base to Intake Manifold Stud nuts mm N/A 12mm head ONLY! 13mm will NOT fit Fuel Filler Neck to Body Bolts split washer flat 4 10mm head JIS or DIN Fuel Line Retainging Clip (metal) to Frame bolts split washer 4 5mm shoulder. 12mm head if JIS but 13mm fits Fuel Pump to Block bolts split washer mm head if JIS but 13mm head fits Gas Pedal assembly to body mounting bolts split washer 4 10mm head JIS or DIN Gas Pedal: Accelerator Cable retainer to firewall split washer 4 10mm head JIS or DIN Bell Housing Vent to Bell Housing Bolts (Passenger Side Vent) Captured split 4 10mm head Clutch Arm Boot Retainer to Bell Housing Bolts (Drivers Side) Captured split 4 10mm head Clutch Cover to Flywheel bolts split washer 4 4mm shoulder. 14mm head Clutch Pedal Pivot Bolt split washer 60mm shoulder, diameter, 12mm head Clutch Slave Cylinder to Bell Housing 1 10?? 10mm 10mm thick nut Clutch Slave Cylinder to transmission mount split washer 5 35mm Shoulder. 14mm head Clutch Slave Cylinder to transmission mount split washer 10mm 4 25mm Shoulder. 14mm head Flywheel to Crank bolts N/M 10mm shoulder. 20 mm threads. 17mm head Transmission to Bell Housing bolts split washer 6 17mm head T-Case Front Extension Housing to T-case Bolts Captured split 4 4mm Shoulder. 12mm head if JIS but 13mm fits T-Case Idler Gear/Selector Shaft Retainer Bolts Captured split 4 4mm Shoulder. 12mm head if JIS but 13mm fits T-Case Output Shaft Cover to T-case housing bolts split washer 4 14mm head T-Case PTO Cover to T-Case Housing bolts Captured split 4 5mm shoulder. 12mm head if JIS but 13mm fits T-Case Rear Bearing Retainer nut N/A 32mm Head. 10mm thick

2 T-Case Shift Shaft Housing to T-case Bolts Captured Split 4 25mm Shoulder. 12mm head if JIS but 13mm fits T-case Shifter Lever Retaining Nut (4 Sp) flat washer 17mm N/A 17mm Head but 19mm will fit T-Case Speedo Housing Speedo Gear Assembly Retaining bolt 1 8mm split washer 4 12mm head but 13mm fits T-Case Speedometer Housing to T-Case Housing bolts (1 of 5) split washer 4 15mm shoulder. 12mm head if JIS but 13 mm fits T-Case Speedometer Housing to T-Case Housing bolts (4 of 5) split washer 4 4mm Shoulder. 12mm head if JIS but 13mm fits T-Case to Transmission Bolts (3 of 5) split washer N/M 90mm shoulder. 17mm head T-Case to Transmission Bolts (Under PTO Cover) (2 of 5) split washer 6 8mm shoulder.17mm head. 32mm thread T-Case Top Shifter cover to T-Case Bolts Captured split 4 4mm Shoulder. 12mm head if JIS but 13mm fits T-Case Vacuum Switch Hard Line Double Clip to Firewall Bolt split washer 4 10mm head JIS or DIN T-Case Vacuum Switch Hard Line Single Clip to Firewall Bolt SEMS 4 10mm Head SEMS Bolt Vacuum T-case shifter linkage pivot nuts split washer 12mm N/A 12mm head if JIS but 13mm head fits Vacuum T-case: Shifter Lever Pivot Assembly to Firewall Under Hood split washer flat 10mm head JIS or DIN Drive Shaft Bolts split washer flat 10mm shoulder. Grade Diff Third Member to Axle Housing nuts split washer 14mm N/A 14mm head Differential Cover to Differential Housing Nuts split washer 14mm N/A 14mm head Differential Housing Studs ? 16mm of threads, a 11mm Shoulder then 10mm threads Knuckle Felt Cover Retainer bolts split washer flat 4 10 mm head JIS or DIN Knuckle Housing Steering Stop Jam nut mm N/A Steering Center Arm Housing to Frame (2 of 4) Side Frame split washer flat 14mm mm head Steering Center Arm Housing to Frame Bolts (2 of 4) Cross Member split washer mm flange head Steering Column Bracket to under dash mounting bolts captured flat 4 12mm head if JIS but 13mm head fits Steering Column Lower Rubber Boot Retainer to firewall split washer flat 4 10mm head JIS or DIN Steering Stop to Knuckle Bolts N/M 14mm Domed head uses jam nut Steering Wheel to Column Shaft Retainer nut N/A Need thin nut Brake Line T junction to Axle Housing Bolt (Front Axle) split washer flat 12mm 12mm head if JIS but 13mm head fits. 12mm nut Brake Line: Coiled line to Firewall Single clip SEMS 4 10mm Head SEMS Bolt Brake Pedal Pivot Bolt split washer 60mm shoulder, diameter, 12mm head Brake/Clutch Pedal Nylon Bearing 2 N/A Nylon "Bearing" Brake/Clutch Pedal Pivot metal Sleeve " N/A 0.51 diameter, inside diameter x length Drum Brake Wheel Cylinder Adjuster Lock Spring Retainer Bolt split washer N/A Straight Blade head Drum Brake Wheel Cylinder to Backing Plate Retaining Bolts split washer 5 12mm head if JIS but 13mm fits Drum Brake Front: Backing Plate to knuckle retaining bolts split washer 12mm head if JIS but 13mm fits Drilled heads for safety wire Emergency Brake Bracket: Bottom to firewall split washer flat 10mm head JIS or DIN Emergency Brake Bracket: Top to dash split washer flat 10mm 10mm head JIS or DIN Emergency Brake: Backing Plate to T-case bolts (3Sp ONLY) split washer flat 12mm head if JIS but 13mm fits (4 sp has 3 20mm and 1 16mm) Rear Drum Brake Backing Plate to Axle Flange Retaining Bolts split washer N/A OEM is a special Head but a 14mm hex head could be made to fit Rear Drum Brake Backing Plate to Axle Tube Retaining Nuts split washer 17mm N/A Front Brake Hard line bracket to frame bolt split washer flat 12mm head if JIS but 13mm fits Alternator Case Bolts (Holds Housing Halves together) split washer N/A 58mm Shoulder. JIS #2 Phillips Head Alternator Front Housing Bearing Plate Retainer split washer N/A JIS #2 Phillips Head Dimmer Switch to Body Bolts split washer flat 10mm head JIS or DIN Flasher Relay to firewall mounting bolts split washer flat 10mm head JIS or DIN Fuse Block mounting bolts split washer flat 10mm head JIS or DIN Horn assembly bolts, early version (holds horn halves together) N/A #2 JIS Phillips head Ignition Coil Clamp Nut N/A Nut is 10mm x 10mm square Ignition Coil Clamp Screw N/A 25mm shoulder #2 JIS Phillips head Ignition Coil Mounting Bracket to Head Bolts Captured split 4 12mm head if JIS but 13mm fits Ignition Coil Stud Nuts for wires split washer flat 8mm N/A Use brass nuts! Power Outlet mounting screws internal toothed lock washer N/A JIS Phillips head Headlamp Body to Headlamp Housing Ring Screws split washer #2 JIS Phillips head

3 Bib Studs to hold Radiator Protective Mesh split washer flat 6mm N/A Nuts 10mm heads Body Mount bolts split washer flat 5 23mm shoulder. OEM ground to point Body: Turn Signal Hollow Mounting Studs split washer 17mm OEM has square end that locks into plastic housing Cowl Vent lift sleeve anchor screws split washer flat N/A #2 JIS Phillips head Cowl Vent pop-up cover mount Nuts split washer flat 7mm N/A 7mm nuts Dash: Gauge Cluster Screws N/A #2 JIS Phillips head PAN head Dash: Plastic cone sleeves to line holes in top dash vinyl 5 N/A Dash: Vinyl Dash Top to dash screws N/A JIS #2 Phillips head Door Hinge to Body Bolts Captured split flat 5 12mm head if JIS but 13mm fits Door Hinge to Door Bolts Internal tooth 4 12mm head if JIS but 13mm fits Fender Apron to Bib Bolts split washer flat 4 10mm head JIS or DIN Fender Apron to Fender bolts split washer flat 4 10mm head JIS or DIN Fender Support to Frame Bolts split washer 4 12mm Head if JIS but 13mm fits Glove Box Knob split washer flat 7mm N/A stud molded into knob Glove Box Door Limit strap (wire) rope) Mounting split washer 8mm N/A Glove Box Door to Dash Mounting Screws split washer flat N/A Phillips Head Sheet Metal Screws Glove Box Door: Gear Shift Plate split washer flat 5.5mm N/A Heater: Front Blower Assembly to Firewall Bolts split washer 4 5mm shoulder. 12mm head if JIS but 13mm head fits Heater: Rear Heater Assembly to Body Bolts split washer flat 4 12mm head if JIS but 13mm fits Heater: Under Dash Heater Core Box to body split washer flat 4 12mm head if JIS but 13mm head fits Heater: Fresh air inlet, Body side vent cover n/a JIS #2 Phillips flat head Seat Belt Anchor to Body Bolts split washer flat 5mm shoulder. 17mm head Seat Frame: Drivers Rear Hinge to Body Bolts split washer flat 12mm head if JIS but 13mm fits Seat Frame: Passenger to Body Bolts split washer flat 12mm head if JIS but 13mm fits Soft Top Bow Bracket (2 brackets) to Wheel Well split washer flat 12mm head if JIS but 13mm head fits Soft Top Bow Brackets: rear bracket to Tub rail (2 Brackets) split washer flat 4 10mm head JIS or DIN Spare Tire Carrier Hinges to body split washer flat 12mm head if JIS but 13mm head fits Tool Box Jack Holder Mount split washer flat 4 10mm head JIS or DIN Transmission Tunnel to body bolts Weld nut split washer flat 4 10mm head JIS or DIN Weld Nut assembly that #127 screws into M6 x 1.0 plain steel 1/2" W x 1-1/2" L x x11/32" H McMaster Carr P/N 90955A Hood Chrome Ornament to Hood Nuts (For Split Hoods) split washer flat 6mm N/A Studs are captured in Ornament. 10mm head Hood Hinge Nuts split washer flat 6mm N/A 10mm head Hood Hinge to Hood Screws split washer flat 10mm N/A Pan head Phillips screw Hood Hold Down Hooks to Hood bolts split washer flat 4 10mm head JIS or DIN Windshield Hinge to Windshield/body frame Screws Cone Star Washer N/A Flat head Phillips screw Windshield Hold Down Hooks to Hood Bolts split washer flat N/A #2 JIS Phillips head Windshield knobs. Studs molded into knob N/A 40mm shoulder. Knob is 50mm in diameter Windshield: Rubber Hood Rests to Hood nuts split washer flat 8mm N/A 12mm head if JIS but 13mm fits Hard top: Door Bows above front doors split washer flat N/A JIS Phillips head Hard top: Fiberglass top to Side Panels split washer flat 4 10mm head JIS or DIN Hard top: Lift Gate Cross Member to Side Panels Captured split flat 4 12mm head if JIS but 13mm fits Hard top: Side Panels to Tub rail split washer flat 4 10mm head JIS or DIN Lift Gate: Hinge to Lift Gate bolts split washer flat 4 12mm head if JIS but 13mm head fits Lift Gate: Lift tube bottom support anchors to hard top sides split washer flat N/A #2 JIS Phillips head Drop Tailgate: Gate Latch Hook to body split washer flat 12mm head if JIS but 13mm head fits Drop Tailgate: Gate Latch to Tailgate split washer flat 10mm head JIS or DIN Drop Tailgate: Hinge to Body and Gate split washer flat 12mm head if JIS but 13mm head fits Drop Tailgate: License Plate Holder bottom split washer flat 12mm head if JIS but 13mm head fits Drop Tailgate: License Plate Holder top split washer flat 10mm head JIS or DIN

4 Front Shock to Shock Tower Retaining Nuts flat 14mm N/A 14mm head Front Spring Pin Retainer to Frame bolts split washer 12mm head if JIS but 13mm fits Rear Shock to (Lower) Axle Shock Stud Retaining Nut flat 17mm N/A 17mm head ( A lug nut will work in a pinch) Rear Shock to (Upper) Frame Crossmember Shock Mount Stud flat 17mm N/A 17mm Head Battery Tray Pedastal to Frame split washer 12mm head if JIS but 13mm head fits Battery Tray to pedastal mount split washer 4 12mm head if JIS but 13mm head fits Bib Hinge Mounting Bolts split washer flat 15mm shoulder 12mm bolt head Front Bumper Support (Triangular) to Frame Bolts (Small Front ones) split washer flat 12mm head if JIS but 13mm fits Splash Guard: Engine Front guard to Frame Bolts Captured split flat 10mm Head Splash Guard: Front Inspection Cover to Engine Splash Guard split washer N/A Phillips Head Sheet Metal Screws Exhaust/Intake Studs in Head. Center mm thickrass 10m N/A 10mm Studs 15 mm in head 20mm for intake/exhaust Exhaust/Intake Studs in Head. Outer two 2 12/10mm mm thickrass 10m N/A Dual size stud: 12mm x 1.25 x 12mm in head 10mm x 1.25 x Code Description 15 Engine 25 Oiling System 50 Cooling System 75 Fuel System 100 Clutch System (Bell Housing/Clutch/Master and Slave 150 Transmission 200 Transfer Case 250 Propellor Shafts 300 Axles 350 Rear Axle 400 Steering 500 Brakes 600 Electrical 700 Body 715 Hood 725 WindShield 750 Hard Top 800 Suspension 900 Frame

5 Notes 2 10mm from '58-12/' threads on the other

6

7 *** Under investigation bu

8