TYLDEN HERITAGE MAIL ORDER PARTS CATALOGUE B MODEL MACK

Transcription

1 TYLDEN HERITAGE B MODEL MACK MAIL ORDER PARTS CATALOGUE Custom Classic Truck & Tractor Restorations Business Hours: Location: 1906 Trentham Road, Kyneton Vic 3444 Australia Note: Our workshop & warehouse are only open by appointment Postal Address: P.O. Box 614, Kyneton Vic 3444 Australia Supplier of after market Mack reproduction and dress up parts Big range of Mack B & R Model bits. Special Interest in: Mack Trucks...Diamond T Trucks...Caterpillar Tractors Trading since tyldenheritage@bigpond.com web: Lee No 3 Pty Ltd A.C.N A.B.N These pages may only be reproduced after obtaining written permission from Tylden Heritage. All rights reserved.

2

3 INDEX FOR B MODEL MACK PARTS 1B AXLE - Section 1 - Diffs, Shock absorber, Hubcaps Springs, CHASSIS - Section 1 - Bumper, Fuel Tank, Caps, Steering, Tail Shaft ENGINE - Section 1 - Engine - Radiator, Starter Motor, Air Cleaner, Power Steering, Water Pipes 2B BONNET & JEWELLERY - Section 2 - Latches, Dogs, Emblems, Mudguards 3B 4B CABIN INTERIOR - Section 3 CABIN EXTERIOR - Section 4 5B DOOR PARTS - Section 5 SEE GENERAL SECTION CATALOGUE FOR OTHER PART OPTIONS 6 GENERAL - Section 6 - Parts for Axle, Brakes, Catches, Dress Up, Electrical, Parts Books, Rubber Parts, Reproduction Cast Parts, Steel Name Plates &, Instruction Plates & Stickers.

4 SECTION 1 - AXLE - B MODEL ALL PRICES ARE SUBJECT TO GST AIR BAG SPRING B MODEL FRONT AXLE - COMPLETE 277 B Model Front axle FA522 larger capacity complete flat end caps RHD - used. $ B Model Front Axle FA 505 lighter capacity complete hubcap type, RHD, does not include hubcaps - used $ We also have front 10 stud B Mack front axles. LHR and no brakes. TIE RODS 402 B Mack tie rod, suit FA 522. Larger capacity has flat end caps screw in male thread ends Lor R $ B Mack tie rod, suit FA 505. Lighter capacity has hubcaps screw in male thread 405 B Mack tie rod super heavy front axle not common in Australia, Has female threads $ $ DRIVE AXLE ASSEMBLYS 285 B Model Single axle diff 4.25 Ratio complete hub to hub with spider hubs - used $ 1, B MODEL REAR AXLE DIFF CENTRES Note: There are two bolt patterns, one has 10 studs and the other type has 16 mounting studs. Axle splines can also vary. 286 B Model Set tandem diff centres only Set front & rear diff centres, ratio 4.53 & Price per set. Suit B Model tail shaft Set Tandem diff centres ratio 6.34, some were on front bull gear -works OK - taken from our own truck for ratio higher change - sold per set 395 Front and rear diff centres for parts only ratio - rust on bull gear - sold per each AXLE SHAFT 126 Axle suit 44000lbs bogey diff with 2 splined ends. Note: There are two splined types - one has pointed and one has flat tops and there is a long and a short - Used. (Photo shows single or light weight drive type) B MODEL GREASE CAPS 123 Domed (not common) type suit FA 522 axle with pressed Mack logo - used - sold per each. $ 2, $ $ $ $ Axle oil caps front flat steel original type with pressed Mack logo FA522 axle - used...add $40 each for chrome plating. $ Page B MODEL AXLE,BRAKE,CHASSIS

5 SECTION 1 - AXLE - B MODEL ALL PRICES ARE SUBJECT TO GST SHOCK ABSORBER - FRONT 320 Mack B Front Shock Absorber with arm type LH. USED $ Mack B Front Shock Absorber with arm type RH - used $ Mack B Ball Joint Only, 83MM (3 1/4 INCH) 9/16 Threads each end - used 317 Mack B Rod. 300mm (12 inch) long with 75mm of 9/16 UNF thread each end - used 319 Mack B Front shock absorber lower bracket - bolts under spring - RH small - used $ $ Photo shows full assembly $ Mack B Front shock absorber lower bracket - bolts under spring - LH large - used $ B MODEL CHROME HUB CAPS 2201 Mack B chrome new front axle chrome hubcaps. Fits FA 505 axle or 2203 adaptor plates. Size 9 inches (228mm) (price per each) NEW. See General Dress Up PARTS SECTION 6D FOR PRICING 2202 Chrome hubcaps front axle with Mack logo (not common in Australai) used - some minor rust - (price per each). SEE SECTION 6H FOR PRICING $ ADAPTER FOR B MODEL HUB CAPS 2203 Aluminium solid cast adaptors machined & drilled (to fit stock 2201 hubcaps to heavier axle which has flat caps) may also be used to fit caps to some rear axles-sold per each. NEW.See General Dress Up Parts Section 6D for pricing B MODEL WHEEL & CLEATS 151 Front Wheel Cleats Photos shows light axle cleats that have hub caps. Price per each - used. As Photos. $ Rear axle steel cleats Price per each - used $ Front spring shock insulator Price Per Each $ Page B MODEL AXLE,BRAKE,CHASSIS

6 SECTION 1 - BRAKES - B MODEL ALL PRICES ARE SUBJECT TO GST ELEPHANT FEET 2754 Top insulator, suit Requird. Price Per Each. See Rubber Parts in General Section 6G for pricing Top insulator suit steel base, 6insx4 1/2 ins 13/4 dowl. 4 Required. Price Per Each. See Rubber Parts in General Section 6G for pricing Lower insulator. Suit & rear end. Steel Base 6 1/8 x 6 1/8 1 3/4 dowl. 4 Required. Price Per Each. See Rubber Parts in General Section 6G for pricing Side spacer of lower insulator Neoprene. 8 Required. Price Per Each. See Rubber Parts in General Section 6G for pricing. Note: Some top insulators have a smaller button diameter and no longer available, we can machine. Add $35 each for this option. HAND BRAKE ASSEMBLY 252 B Model hand brake assembly. Drum, centre & lever. $ CONVERSION PLATE TO TAKE MODERN TREDDLE VALVE 581 B Model brake foot (treddle) valve conversion plate only to bolt into original opening. Suitable for use as single or double circuit brake system. See General section 6B for treddle valve part no 579. Pedal assembly mounting part 580 curved pedal part no 582 as used on RHD only, SEE CABIN INTERIOR FOR PRICE FOOT VALVE CURVED PEDAL 582 New RHD Curved brake pedal with Mack logo. Only fit late pedal adapter. Casting only, not drilled or detailed. NEW. See General Section 6, Brake Parts for pricing BUMPER BAR 21 B Model black steel extended bumper bar includes top plate (no mounting brackets) - new $ 1, B Model new stainless steel extended bumper. Bar includes top plate (no mounting in brackets) - NEW $ 2, B Model Bumper Extended Brackets - used - PER SET $ Page B MODEL AXLE,BRAKE,CHASSIS

7 SECTION 1 - CHASSIS- B MODEL ALL PRICES ARE SUBJECT TO GST TOW HOOKS - ORIGINAL B MODEL 281 Tow Hooks (bumper bar) L & R sold per each - used $ TOW HOOK SPECIAL BOLTS 247 Bolts - zinc plated - extra long for tow hooks 7/8 x 9T x 8 inc Long - 2 Per Truck - new. Price per each. $ 9.00 CHASSIS CROSS MEMBER 138 B Model Arched Cross Member - Good Condition $ B Model Rear of Cabin cross member with cabin rubber locators $ B front spring cross member with radiator rubber locator cups, pressed channel. $ CHASSIS COMPLETE 379 Mack B61S Single WB 13ft8" - chassis with spring hangers. $ Mack B61RS Tandem WB - 14ft 3" = chassis with rear - light weight spring $ 1, FRONT SPRING HANGERS 339 B61 type front spring hangers L&R $ B61 type rear front spring hangers. L&R. (photos includes front cab mounting) $ Page B MODEL AXLE,BRAKE,CHASSIS

8 SECTION 1 - CHASSIS - B MODEL ALL PRICES ARE SUBJECT TO GST FUEL TANK CAPS 262 Brass fuel cap large type with four lugs - Snyder Buffalo cast from brass & machined with new 100mm thread 130mm Top - new. SEE GENERAL CAST SECTION 6H FOR PRICING 273 Brass fuel cap 55mm thread (2 1/8). Top 70mm (2 5/8) Snyder - Used $ FUEL TANK FILLER 363 Fuel tank filler tube aluminium for welding into tanks to take large B (part 262) filler caps. Note: not machined - new. See General Cast Section 6H for pricing. POA 363a With clean up and new thread for Buffalo cap 262 ready for welding into tank POA FUEL TANK TAP 1395 Fuel tank brass stop tap - 1/2 female, 1/2 male, NTP thread with round gate weheel handle - looks like original. NEW. Bin See general 6H Cast Parts for pricing. TANK STRAPPING (oil & fuel resistant nitrite) 1566 All suitable for air tank, air cleaners etc, all strapping sold per metre. (Photo shows 63mm).See Dress Up Parts - Section 6D for other options and price. (Photos shows connection..not included) ROLLOVER - See Rubber General Section 6G for pricing Roll over shoulder 40mm. Price per metre 2521 Roll over shoulder 50mm. Price per metre 2522 Roll over shoulder 63mm Price per metre 2523 Roll over shoulder 80mm Price per metre Page B MODEL AXLE,BRAKE,CHASSIS

9 SECTION 1 - CHASSIS - B MODEL ALL PRICES ARE SUBJECT TO GST SQUARE EDGE see General Section 6H for pricing 2525 Square Edge 32mm. Price per metre 2526 Square Edge 50mm. Price per metre 2527 Square Edge 80mm. Price per metre PITMAN ARM 327 B Model Pitman arm for B61 - used $ OPTIONAL STEERING COLUMN FOR LARGER DRIVERS. 206 B 75 Model Steering Column without box for B73,B75, B77, B615 & bracket.note: this has uni that allows a lot better steering wheel angle & driver gut clearance will not fit to standard B61 type steering box and only suitable when later type steering box is used that has separate steering column. Supplied with dash bracket. WHEEL SEALS 1852 Axle seal for 44000lbs. B Model OD 6 1/4 ID 4 1/4 modern type with inbuilt speed sleeve $ POA 1853 Pinion seal front diff 44000lbs B Mack. POA TAIL SHAFT PARTS 139 B Model Centre Bearing & short jack shaft for wheel base extension - used $ MUDFLAP - SEE RUBBER PARTS - GENERAL SECTION 6G DRAG LINK COVERS 303 B Model Drag link leather grease covers with lace - new. See Rubber Parts in General Section 6G for pricing. $ POWER STEERING 316 Original power assist booster type steering kit - fits B mack - Used (note: pump not included) as taken off used trucks, add $500 - to cost for belt driven pump or standard generator drive pump. See engine parts in next section for pump options. 384 Air tank holding bracket, also used on B Mack round fuel tanks. Price Per Each $ 2, $ Page B MODEL AXLE,BRAKE,CHASSIS

10 SECTION 1 - CHASSIS - B MODEL ALL PRICES ARE SUBJECT TO GST BATTERY BOX & BATTERY- SEE SECTION 7 OR CONTACT OUR OFFICE FOR PRICING. 680 Heavy duty Mack type battery box, bottom section holds 2 batteries with rubber latch - as on R Model - new. See R Model Mack Parts for Pricing 681 Black steel ribbed top battery box lid cover - correct for R but needs optional chrome latch for correct B Model. See R Model Mack Parts for Pricing 682 Steel battery hold down bracket, hold the batteries securely - not stocked. See R Model Mack for Pricing BATTERY BOX & BATTERY 683 Nickel Cadmium carriage bolt. Holds batteries bracket down - 2 required (sold as kit) - not stocked. See R Model mack for Pricing Page B MODEL AXLE,BRAKE,CHASSIS

11 SECTION 1B - B MODEL ENGINE ENGINE - COMPLETE engine or END673D used (ask for details of model & available including Mack E9 stock). Note: Engine prices are subject to condition and accessories fitted. $4, B MODEL GEAR BOXES & PARTS 1096 Gear Box 10 or 15 speed sold with money back guarantee, if returned within 4 weeks less freight cost $1, Gear Boxes - 18 Speed Quad. Sold with money back guarantee if returned within 4 weeks less freight paid $2, Joey box ex B Model with chassis support brackets. 3 Speed Spicer Brown Lipe Model 8031 with hand brake.good Condition. Sold with money back guarantee if returned within 4 weeks less freight paid. $2, PTO COVER 1110 Large PTO cover plates $ B MODEL GEAR BOX PTO 83 Gear Extra deep adapter (Note: there are two types with power auto No GA303 & GA328 that has a trust washer. The face of the plate to the tip of the gear is 4 inches. $ PTO Assembly with pump to suit adaptor above $ ENGINE MOUNTING INSULATORS 169 Mack B rear engine mounting rubber. Set includes 4 upper & 4 lower. They are 70mm dia & 30mm high with 5/8 hole. Sold Per set of 4 (8 PIECES)..See General Section Rubber Parts Section 6G for pricing RADIATOR & CABIN MOUNTING INSULATOR CUP TYPE 154 Mack B model special cup type cab mounting insulators, 2 large & 2 small required. They are 70mm diam & 30 high with 5/8 hole. They require a 8 inch bolt at rear. See part 193 insulators. Sold as a set of 2..See General Section Rubber Parts Section 6G for pricing. 170 Radiator Shutter Control Thermostat (sends signal to the air actuator to open) - used..bin 134 $ As NEW $ B - B MODEL ENGINE

12 SECTION 1B - B MODEL ENGINE ALL PRICES ARE SUBJECT TO GST RADIATOR SHUTTER AIR CONTROL SHUTTER & LOUVRES 166 Radiator shutter louvres Kyser automatic - suit B61 and similar models - no controls - Used $ B 61 & similar model radiator core only - looks OK -BUT NOT TESTED - used $ B615 RADIATOR PANEL ASSEMBLY 140 Top & bottom radiator tanks, side panels & headlight panels cast from aluminium with louvres (with radiator) - suit B73-75 & 615 & other models $2, RADIATOR GASKET 2860 Rubber Gasket - top & bottom tanks - B615 & 75 and the like - 2 pieces. 1mx150x1.5mm - see insertion rubber parts General Section 6G for cost 389 Radiator cap - suit most early models, 615, 7PSI.. B315 $ Engine thermostat used. Mack part no 657GC 225A P2 $ Radiator Shutter control air ram actuator assembly - USED $ Radiator control piston replacement seal suit part new...b272 $ Radiator shutter air ram actuator replacement $ R MODEL 3169 R Model air starter motor - complete 10hp oil type. Used. Will fit some B Models. Ask re pricing. NOTE: PINION LENGTH CAN CARY 9 1B - B MODEL ENGINE

13 SECTION 1B - B MODEL ENGINE ALL PRICES ARE SUBJECT TO GST RADIATOR GASKET (cont) STARTER MOTOR STARTER - ELECTRIC 918 Starter motor - suit 711 & other early model engines - 12 volt - used $ GENERATOR etc 73 B Model Generator used. $ POWER STEERING PUMP 124 Generator with regulator and power steering drive type and oil pump as fitted to B Models with power assist optional steering from new $ DRIVE COUPLING 137 Rubber Drive coupling for power steering pump of Generator (as above)..bin 131 $ POWER STEERING PUMP V8 365 Power Steering pump with drive - suit 864 V8 - Used $ BELT DRIVE 386 Power Steering pump -Belt drive $ Power Steering Pump Bracket $ STARTER TANK 276 Air starter tank - used. Note: they are not tested and are sold on an as is where is basis and may need new sections & will need full testing by an approved authority, before used as pressure vessel tank. 870mm long x 590mm diameter. $ STARTER VALVE & LEVER 342 Air starter valve only - B Model - fits under cabin floor held by U bolts. $ Starter Valve control lever to suit 342 only with new knob - B Model $ B - B MODEL ENGINE

14 SECTION 1B - B MODEL ENGINE ALL PRICES ARE SUBJECT TO GST AIR STARTER VALVE R MODEL - B MODEL OPTION 3060 Air tank starter valve, suitable for remote control electric over air conversion option as used on R model.- NEW. See R Section 7 for pricing V Solenoid valve air starter for conversion to electric over air. suit air tank valve Above new. See R Section for Pricing AIR CLEANER PARTS AIR CLEANER TOP HAT RAMS & PRE CLEANER 476 Air Cleaner Round Top Hat new fit most 4 1/2 inch pipe applications. All metal painted black or can be chromed- new. $ REPLACEMENT DRY AIR CLEANER - B MODEL 150 B Model look a like Air cleaner paper elements dry type - replacement for oilbath - suits B Model (clamps are separate) - bolts on in place of original - new - 12 inch (300mm) diam, 4 1/2 ins (115mm) inlet, 4 1/4 ins (107mm) outlet. $ Dry element adaptor clamps sold per each suit ABOVE 150 $ B MODEL OIL BATH NOTE: There are different types of the B series air cleaners. Some had side entry, others had bolts to hold bowl others a clamp and there was also different diameters. B MODEL OIL BATH AIR CLEANER 217 B Model Air cleaner oil bath (top inlet) MOST LATER Aust B Models had this type - complete inlet 4 1/2 inches (115mm) outlet 4inches (100mm) - no brackets - diameter - 12 inches (300mm) - used. Note: Top not included. B615 MODEL OIL BATH AIR CLEANER 215 B615, B75, B73 air cleaner top inlet oil bath type 13 inch 330mm diam, 4 1/2 ins 115mm inlet & 4 ins 100mm outlet. $ $ B MODEL OIL BATH SIDE ENTRY 218 B Model early Air cleaner oil bath (side inlet) (it seems many earlier had this but not as common and no air vent) used $ B - B MODEL ENGINE

15 SECTION 1B - B MODEL ENGINE ALL PRICES ARE SUBJECT TO GST AIR CLEANER SUPPORT BRACKET & BASES 203 B Model RH Standard Air Cleaner - bolt on support bracket only, bolts to cabin with hole for air vent, later type air cleaner bolts to this bracket with 2 support brackets used $ B Model Air cleaner support bracket oil bath type - 2 required - price per each - used - suit 217. $ B MODEL INLET PIPE 122 Air cleaner pipe - fit inside cabin on standard on most RHD B Model. Connects to air cleaner pipe - made from fibreglass - used. $ AIR CLEANER ENGINE ENTRY SOCKET 204 RH air cleaner pipe entry socket - suit B75 & 73 with longer bonnet. Not original fitting on standard B 61 type model. This fitting bolts to firewall and bonnet corner, is cut to close over it. $ DIP STICK 351 Dip stick with mount - suit 711 $ ENGINE ALLOY WATER PARTS Top water pipe elbow outlet goose neck connects head mounted water outlet to radiator - there is also a short type - used. $ Head mounted water manifold outlet - front. Bolts to head. Has large opening for goosenick and thermostat - 500mm long - USED $ Head mounted water manifold outlet - rear, bolts to head. - Note: there are 2 lengths. - USED $ Oil cooler elbow bolts onto 67 some have a top outlet - USED $ Oil cooler water outlet (bolts to end of oil cooler) - used Note: There are square & angle ends. $ Cooler oil assembly (water outlet not included) - used $ B - B MODEL ENGINE

16 SECTION 1B - B MODEL ENGINE ALL PRICES ARE SUBJECT TO GST WATER PUMP KIT 3106 Suit most 60's & 70's Macks 5/8 shaft. (Note: shaft lengths do vary with number of pulleys and front bearing sizes may vary also) $ ENGINE - Luberfiner Element 1007 Luberfiner Oil Filter - length 373mm x 200 diam- NEW - Fits most B Models. $ Luberfiner Oil Filter - length 380mm (15 inches) 190mm (7 1/2 inches) diameter. Suit later model like 675 engine. $ Cast radiator top tank holding screws for 1 1/2 x 3/8. Suit B and most models with cast radiator. 4 required. Price per Each..NEW..Bin 2920 $ B - B MODEL ENGINE

17 SECTION 2 - BONNET AND SIDE JEWELLERY ALL PRICES SUBJECT TO GST B MODEL MACK CHROME SCRIPT 70 B Model chrome "Mack" script for Hood sides, cast from brass not finished or chromed. L&R. Sold per each. Bin B Model Chrome "Mack" script for Hood Sides - L&R -NEW - Sold per each 304 B Model chrome "Mack" script for hood sides -L & R. USED Sold per each-most have some pitting. SPECIAL CAST MACK SCRIPT 1325 Mack script cast from aluminium and shaped so when fitted to a body and edges detailed and painted & it gives the impression of a body pressing. 300x90mm $ $ $ $ Mack small script cast from aluminium suitable for fitting into steps and the like - 115x50mm. $ SPECIAL PROFILED MACK SCRIPT 1337 Mack script profiled from stainless steel, a cut but very neat, 150 long & 45 high & 5mm thick - not detailed $ Mack script profiled from steel cut very neat 300L 90H 6mm thicknot detailed. $ Mack oval enamelled grille emblem. Suit B81 type trucks. Bin 345 $ B MODEL MACK HALF DOG 10 B Model half dog emblem - hood sides - left & right - sold per each - NEW - 2 required $ B Model half dog - used all have some pitting $ CURVED B61 TYPE DOG BASES MOUNTING - STEEL COWL 4 B 61 and similar Model Curved Base for Bulldog Hood Ornament - Chromed - New. Ex USA $ B61 Model curved dog base for bulldog hood ornament with some pitting, maybe OK for rechroming - USED. $ B61 Model curved dog base for Bulldog Hood Ornament, cast from brass, not finished or chromed or tapped. - new. Add $184 for detailing, drilling & chroming. $ EXCHANGE 228 B61 Model curved dog base as above rechromed to new standard. $ Page 14 2-B MODEL BONNET JEWELLERY

18 SECTION 2 - BONNET AND SIDE JEWELLERY ALL PRICES SUBJECT TO GST BULL DOGS - LONG EARS & TAIL 654 Chrome Bulldog hood dog ornament early type with long ears and tail - used suit all early Mack models including very early R Model (note: some discolour and/or pitting) - USED. $ A New old stock Mack long ear dogs. As fitted to Mack trucks $ B Model super proto type round Bull Dog - as developed and displayed on the early proto type B Model. Same size as original. Craftsman reproduction cast from solid stainless steel. NEW $ SMALL BULL DOG - LONG EAR & TAIL 660 Small dog, stand up 100mm early type - Pre 1979 used on ash trays and some Mack Jr. $ Base for the above dog - tapped so small dog (660) stands on level base. $ ALSO SEE SECTION 8 HINGED CAP BULLDOG BASE 30 B Radiator hinged cap - used but rechromed. $ B Model Bail Clip to hold above radiator cap 344 closed - new Bin 30 $ B Model bail clip to suit used. Bin 30 $ MOUNT KIT HALF DOG & MACK SCRIPT 39 B Model Emblem mounting kit - stainless steel cup holds 2 for half dogs & 2 for big Mack emblems to hood (8 per truck) - sold per each - NEW. B10 $ 5.50 B MODEL HOOD/BONNET MODEL NUMBERS 8 Chrome model hood emblem recast from brass, not finished or chromed. Models available - B20, B42, B60, B61, B73-B85, B95, B422, B421, B615, B815, H60 - W71. For hand detail and chrome plated add extra $50.00 $ Note: We can make any model number but a pattern cost would apply of $60.00 V8 EMBLEM - NOTE ONLY ON SOME MODELS 205 B Model V8 Bonnet Emblem cast from brass - not finished or chromed - sold per each. See section 6H for pricing 207 B Model V8 chrome emblem, detailed & chromed with threaded pins. All models which had a chrome badge. Gold available. 90mm wide 60mm high and 8mm thick. See General Section 6H for pricing. NEW Page 15 2-B MODEL BONNET JEWELLERY

19 SECTION 2 - BONNET AND SIDE JEWELLERY ALL PRICES SUBJECT TO GST MACK GRILLE EMBLEM NAME PLATES - Fits B61 & similar 460 long 50 high 5 B Model Front grille emblem name plate "Mack" made from pressed brass & chromed, bolts to grille face - new $ B Model front grille emblem - Mack name plate - used. Has some small dents etc. $ B Model front grille emblem cast from brass and rechromed $ HOOD/BONNET TRIM STRIPS 34 B Model stainless bonnet (hood) trim strips. Set of 6 (one set per truck - 2 long, 2 short) with set of stainless trim special holding clips - new..see tube in corner for long strips. 12 B Model long stainless hood trim strips (2 per truck) - used - sold per each. $ $ B Model short stainless hood trim strips (4 per truck) - used - sold per each. $ Clips to hold stainless trim strips (14 per truck) - sold per each - new. B34 $ 2.00 Australian made badges cast from brass. Are a lot stronger and will not pit like cast ones and to original sizes and fit a lot better with long pins. THERMODYNE SCRIPT BADGE WITH MOUNTING PINS TO SUIT ORIGINAL HOLDES IN BONNET (HOOD). 292 Thermodyne script badge - not finished or chromed - 2 required (Price per each) $ B Model Thermodyne badge, fully hand detailed and chromed, fitting pins in bonnet and they are nice and straight - new - (Price per each) $ DIESEL BADGES 87 Diesel script badge, cast from brass, not finished or chromed. $ Diesel script badge, cast from solid brass, detailed and chromed, fitting pins fit holes in original bonnet. Bin 19 $ Diesel script badge - used (some pitting) - (price per each) $ Page 16 2-B MODEL BONNET JEWELLERY

20 SECTION 2 - BONNET AND SIDE JEWELLERY ALL PRICES SUBJECT TO GST BONNET (HOOD LATCHES) B MODEL ROUND BONNET LATCHES 191 B Model Secondhand old style round hood latch & catch - black - used - some rust $ B Model Reconditioned old style round hood latch & with catch rechromed with new spring & rubber bumper with chrome cap change over service only or add cost of 191. (10 pieces in all per latch) BONNET LATCH SPRINGS 161 Replacement springs for round bonnet latch, also suitable for square latches. 80mm long x 13mm wide. NEW.. Price per each.. B141 $ $ R MODEL MACK (Hood Latches) 3290 R Model black hood latch with square body - new will fit B but not original - 4 required per truck - Note: bottom pin needs turning for some models - sold per each - catch is extra $ As Above...Chrome Plated $ R Model black hood catch square body NEW will fit B model but not original sold per each $ As Above...Chrome Plated $ R MODEL BLACK BONNET LATCHES (fits B) 2846 B & R Model hood latch replacement rubber bumper - sold per each with screw & washer - caps are brass. See Rubber Section 6G for Pricing. BONNET LATCH REPLACEMENT RUBBER 2847 Bonnet latch replacement rubber only - not as thick as 2846 new - price per each. See General Rubber Section 6G for Pricing HOOD/BONNET HINGE ONLY 28 B Model Stainless steel hood centre hinge cover - runs full length of bonnet - new - one piece. (clips not included). Suits all models. Just cut to length. Bin 24 $ Star counter sunk head S/S B bonnet (hood) hinge end. Holds down screws. NEW. Supplied with 2 nuts & flat washers. Price per each. Bin 2940 $ B Model replacement hood channel for spot welding to existing bonnet - 2 pieces. Used to make special bonnets or repairs. Sold as a pair. NEW. $ Page 17 2-B MODEL BONNET JEWELLERY

21 SECTION 2 - BONNET AND SIDE JEWELLERY ALL PRICES SUBJECT TO GST HOOD/BONNET HINGE & CAPS SETS These also work on some Brockways, all Reos & Durant. Other model trucks and also on 30's cars with side lift type bonnets (hoods). 29 B Model hood hinge end cap & strap kit (holds centre hinge part no 28). Price per set, two end pieces - new. B24 $ B Model original bonnet star wheel hood (bonnet) Prop RHS & LHS - Used - Sold seperately. Note: has some minor rust $ HOOD/BONNET PROP NOTE: Standard B model bonnet star wheel hood props are 270mm ( 10 3/4 inches). Closed 420mm (16 3/4 inches) open. 726 After market bonnet/hood props 285mm closed and 470mm open - new $ GRILLE & RADIATOR SHELL - SUIT B61 & SIMILAR MODEL TYPES 3 B Model pressed steel Radiator Shell for B61 Style Truck - used. $ BEZEL - B MODEL HEADLIGHTS - (outside cover) HEAD LIGHT BUCKET 850 B Model headlight bucket assembly and LH round beam lens & wiring pig tail without stainless steel locating ring - new $ Head light bucket only mounts into panel - used $ HEADLIGHT BASE 233 Headlight base mounts into headlight bucket 236 screws to fit it - used $ HEAD LIGHT CHROME LENS HOLDER 236 Headlight lens holder holds glass to bucket used $ Page 18 2-B MODEL BONNET JEWELLERY

22 SECTION 2 - BONNET AND SIDE JEWELLERY ALL PRICES SUBJECT TO GST BEZEL - B MODEL HEADLIGHTS - (outside cover) 2 B Model New Polished original Stainless Steel Headlamp Ring Bezels - per each $ B Model Used Ring Bezels generally made from zinc, Used - Price per each - Fair condition - would need painting. $ B Model used ring bezels, made from zinc, in good condition and repolished. HEADLIGHT SCREWS 2940 Special stainless screws to hold B Model (B etc) headlamp rims - 6 required per truck - Pan Head 3/16 x 1 1/2 UNC. No nuts. New - sold per each. Bin 2940 $ Stainless screws to hold head light rims 4.2 x 45 long. B43- B61 etc. Bin 2940 $ Chrome head light bezel suits B80-81 style steel fronts, also DM and Flintstone & Tylden Mack B Jr. Size rear ID 210mm front ID 185mm x 30mm deep. Takes 7 inch (180) light. Sold per each. $ B MODEL PARK LIGHT USED 119 Chrome original outer parking light cover - no glass lens - used. Add $20 each for rechroming. $ Chrome original outer parking light cover with original WHITE glass lens - used. $ Parking light base - screws into mudguard - used. $ B MODEL - PARKING LIGHT - WHITE (ACRYLIC LENS) NEW 3336 Parking light- white acrylic lens complete assembly - does not have correct chrome cover but optional Part 230 mounts into it for original look - New - Price per Each. See General Section 6E for pricing. Bin Parking White OR Amber acrylic lens - only suits new. See General Section 6E for pricing. Page 19 2-B MODEL BONNET JEWELLERY

23 SECTION 2 - BONNET AND SIDE JEWELLERY ALL PRICES SUBJECT TO GST BLINKER (TURN SIGNAL) LIGHT 772 Fender (mudguard) turn signal LED round face look a like 100mm light with chrome bezel - amber both sides - suits B & R model & other US built trucks - SOLD PER EACH SEE GENERAL 6E FOR PRICING & OTHER OPTIONS BLINKER WIRING COVER BOOT 773 Turn signal wiring cover boot kit fits over wiring under fenders (mudguards) turn signal light (blinker above) - SOLD PER EACH $ BLINKER MOUNTING WEDGE (suit B Model) 774 Turn signal spacer wedge on top of front fender to level blinker light - 2 per truck - new. Sold per each. Bin 763 $ 9.10 FRONT MUDGUARD (Fender) 142 B Model mudguard LH or RH $ MUDGUARD INNER PANEL 282 B Mack inner mudguard splash panel LH or RH. Used $ Removal fender service panel B61 & similar L&R- used - price per each - USED $ B MODEL REMOVABLE FENDER (Mudguard Panel) 2811 Rubber bumpers for removal top fenders engine excess panel 10 per truck - sold per each. See General Rubber Section 6G for Pricing. 111 Screws hold fender panel 4 per side - price per each $ J Clips for fender panel screws - 4 per side - price per each. $ Retainer washers hold removable fender screws in place when panel is off vehicle. Price per each. $ B Mack removable mudguard (fender) screw set. Full set of clips part 2591, screws - part no 111, screw retaining washer - part no 113, rubber bumpers - part no They hold screw in panel when removed from trucks. Set of 8 in kit. $ SEE 4 PHOTOS ABOVE FOR DETAILS OF SET. Page 20 2-B MODEL BONNET JEWELLERY

24 SECTION 2 - BONNET AND SIDE JEWELLERY ALL PRICES SUBJECT TO GST HEAD LIGHT PANEL 290 Headlight Panel B61 & similar - bolts between radiator shroud & mudguard pressed steel - L&R - USED - price per each $ B Model Headlight panel - suit B73 & B75 & 615 & similar - cast aluminium - USED POA HEADLIGHT PANEL INNER 283 Inner head light panel assembly L&R - Used - suit B61 Part No 290 above. & similar $ HEADLIGH PANEL SCREWS 2591 J Nuts for B Model with steel headlight panel 3/16. See General section 6C for pricing. BONNET WEBBING 2692 Woven type hood lacing - 30x8mm (1 1/4 x 3/8). Sold per foot. B Model rear cab end 2x1070mm per side. Supply B Model steel front 2x600. B B 61 type. B Model Alloy front 2x700. B 615 type B Model - See Part no rear & 10 front. Set of 28 per truck for T Clips for back and front. $ Page 21 2-B MODEL BONNET JEWELLERY

25 SECTION 3 - CABIN INTERIOR ALL PRICES SUBJECT TO GST ASHTRAY 295 B Model original ash tray - complete - Used $ CABIN LINING 25 B61 Cab back cover kit (original style), fits below rear window - trimmed in tan vinyl in 2 sections - new. (Photos shows each side) $ B61 Headliner (original style) made to look original trimmed in tan vinyl - new. Colour options are available. $ FIREWALL INSULATION 49 B Model Firewall insulation under dash down to floor mat, cover with heavy insulation on the back for noise & heat-original type RH drive model with clutch pocket- new $ CLUTCH RUBBER 2482 Clutch pedal rubber replacement pad. See Rubber Parts in General Section 6G for pricing. DASH CABLES 42 Original engine stop cable used. Cable broken. Suitable for fitting new cable to keep original look - used $ B Model Twist & lock throttle cable- original knob used..note: 42 & 43 are used and may require new cable but have the correct knobs to give dash original look - used $ DASH PANEL 74 Dash panel - second hand (no gauges) - may have extra holes. - USED $ DASH & GLOVE BOX EDGE SEAL 2538 Dash panel rubber mounting edge seal (1500mm). Fits over inner edge/lip to save paint. Photo shows end view. Supply 1.4m for B glove & dash board. (SEE GENERAL RUBBER SECTION 6 G FOR PRICING) DEFROSTER DUCT 293 B Model Defroster duct plate bolts on top of dash L&R are the same - $ price per each. Page B MODEL CABIN INTERIOR

26 SECTION 3 - CABIN INTERIOR ALL PRICES SUBJECT TO GST B MODEL HIGH BEAM LIGHT 872 B Model original style high beam light - Red lens. See General 6E for pricing. CIGARETTE LIGHTER - ORIGINAL TYPE 818 Chrome cigarette lighter - suit B Model and most cars and trucks, (element & dash well & pig tail) - new. See General 6E for pricing. DIMMER (DIPPER) - DIPPER SWITCH - FLOOR MOUNTED. See General 6E for pricing 914 B Model old style headlight dimmer switch - floor mounted - suit B Model & other early model cars & trucks. NEW. See General 6E for pricing. SWITCHES - HEADLIGHT 904 B Model Original Style Push Pull head light switch with fuse - 2 positions - black knob. NEW. See General 6E for pricing. IGNITION SWITCH 856 Door & ignition lock set includes 2 door tumblers and one ignition tumbler with 2 matching keys. B88, See General 6E for pricing. 855 Two position ignition switch with 2 keys, Suit 3/4 inch dash hole. Made in the USA by Cole Hersee..B818. See Section 6E for Pricing 857 As Above but suit 1inch dash hole. Mack No MR3172P2. Suit B Mack...B818 See Section 6E for Pricing KNOBS - Dash 910 Black knobs with white (marker light engraved into knob) 3/16 UNF thread for New. See Section 6E for pricing. BLINKER (TURN SIGNAL) SWITCH 771 B & R Model original chrome handle turn signal switch - mounts on steering column - as fitted on original - new. SEE 6E FOR PRICING SPEEDO CABLE 3368 R Model speedo cable with 2 types of adaptors -112 Length 3050mm. Fits most B Models. $ TACHO CABLE 3370 R Model Tacho cable with 3 types of adaptors. 2250mm long. Fits most B Models. $ Page B MODEL CABIN INTERIOR

27 SECTION 3 - CABIN INTERIOR ALL PRICES SUBJECT TO GST BUG EYE INTERIOR LIGHTS (Inside) 861 B Model Optional Dome bug eye type interior light - fits above door on each side - USED - Price per each $ New Sorenson USA VR 81 12V voltage regulator POS ground new Regitar RVR 18 regulator Neg Ground $ GLOVE BOX 61 Cardboard type glove box liner pocket - original style - new $ Glove box latch - Used $ Glove Box Catch for door latch - used POA 2538 Grooved rubber strip to fit edge around glove box and dash 1400 mm.(see GENERAL RUBBER SECTION 6G FOR PRICING) 257 Glove Box hinges - L & R - sold per each. NEW. Note: You would need to change one as we only have one side. Bin 155 $ Glove box door - secondhand - no hinge or catch $ Glove box support frame - fits behind at the top and holds the lock catch. $ Side bracket support for hinges L&R - price per each $ GLOVE BOX BUMPERS 2828 Glove box rubber bumpers (4 per truck) sold per each- new. 8mm high 11 wide at top 13mm long tip to tip. (SEE RUBBER SECTION 6G FOR PRICING) Page B MODEL CABIN INTERIOR

28 SECTION 3 - CABIN INTERIOR ALL PRICES SUBJECT TO GST FLOOR MAT EDGE COVER - CAST ALUMINIUM 1348 B Model cast polished aluminium kick plate with Mack logo to cover edge of carpet (mat), priced per pair - new B61 type cabin - not suitable for B73 or B75 without splicing $ FLOOR MATS 2761 B61 style cab front rubber original floor mat with Mack logo. Heavy backing. (SEE RUBBER SECTION 6G FOR PRICING) FLOOR MAT (REAR UNDER SEAT) 2762 B Model Rear rubber floor mat (goes under seat) with heavy backing - new (SEE RUBBER SECTION 6G FOR PRICING) LOOSE FLOOR MATS 2771 Loose Floor mats with old Mack logo - sold as 1 pair (L&R) - Black with red on white Mack logo - new - Look Great - size 550x450, one has cut out in corner - new. (SEE RUBBER SECTION 6G FOR PRICING) MAKE YOUR OWN FLOOR MATS 2640 Roll of big rib rubber sheeting 2m wide - make your own floor or ute tray mat - sold per metre. (SEE RUBBER SECTION 6G FOR PRICING) STEERING WHEEL 130 B Model secondhand steering wheel - original, some cracks not RW. Check spline diam 22 inch - used. There are 2 similar sizes with spline American trucks, one is 15/16 & one is 1 inch. The smaller one will interchange with many new ones. $ HORN BUTTONS 58 B Model original horn button with Mack logo - Used $ B Model horn button centre without Mack logo - just a replacement centre - new. Note: photo with shows Mack ID plate centre. $ STRIKER PLATE COVER - DOOR 324 Door catch striker plate cover, fits over 95 & 96 door catch. (part of the cabin) $ Page B MODEL CABIN INTERIOR

29 SECTION 3 - CABIN INTERIOR ALL PRICES SUBJECT TO GST SEAT BRACKETS 141 Bracket driver seat cushion - up & down bolts to seat at front underneath to give two locations for height at front of seat, they are L&R. $ Bracket driver seat cushion - up & down bolts to seat at front underneath to give two locations for height at front of seat, they are L&R. $ SEAT FRAME 242 B Model RH driver seat frame complete with forward and back adjusters - used - as original $ B Model LH passenger set frame - used - as original $ SUNVISOR INTERNAL - (INSIDE CAB) 296 B Model interior sun visor LH, complete, taken from USA trucks (secondhand needs to be recovered). Replace cardboard backing and recover as original. Note: will need bracket (part no 66) to fit to RH side. SUNVISOR - INTERNAL 66 B Model RH internal sunvisor support bracket only - cast from brass not finished, would require drilling and making arm or use LH - part no 296. Bin 347 $ $ HEATER 212 Original B Model heater, mounts inside cabin (used). They are designed to fit on RH side and are out of LHD trucks. $ B MODEL SEATS 160 B Model RH standard driver seat - squab and rear cushion - 2 sections - PRICE PER SECTION (need to be recovered. They are LHD truck cover reverse side of backing) $ B Model LH standard seat - squab and rear cushion - 2 sections - PRICE PER SECTION - (add extra $ to recover. They are from LHD cover reverse side of backing) $ DRIVER SEAT ADJUSTER 35 Driver seat adjuster slider with handle forward and back (pair) - Used. $ T bolt with rubber washer, holds rear of passenger seat to frame at top. $ 9.10 Page B MODEL CABIN INTERIOR

30 SECTION 3 - CABIN INTERIOR ALL PRICES SUBJECT TO GST THROTTLE - (ACCELERTOR) 52 B Model fuel pedal kit (pedal, stand, pin & clip) as original with Mack logo - NEW $ As above but used, May have some wear. $ B Model fuel pedal only - with Mack logo - new $ a As above but used, May have some wear. $ BRAKE PARTS (SEE GENERAL FOR OTHER BRAKE OPTIONS) 581 B Model brake foot (treddle) valve conversion plate to bolt into original opening. Suitable for use as single or double circuit brake system. See General section 6B for treddle valve part no 579. Pedal assembly mounting part 580 curved pedal part no 582 as used on RHD only SEE GENERAL SECTION 6B FOR OTHER OPTIONS. $ B MODEL FOOT VALVE CURVED PEDAL 582 New RHD Curved brake pedal with Mack logo. Only fit late pedal adapter. Casting only, not drilled or detailed. NEW. SEE GENERAL SECTION 6 CAST PARTS FOR PRICING WINDSCREEN CENTRE COVER PLATES 308 Windscreen centre vertical cover strip inside cabin - used $ REPLACEMENT WIPER BLADE 175 Replacement B Model wiper blade - 2 required - sold per each - new. 300mm long with hole for holding screws. $ WIPER ARM 176 Original painted steel wiper arm - 2 required - sold per each - used, may have some rust. $ Wiper arm original style - stainless steel - sold per each. New. $ Wiper arm - stainless steel, fit ok but has kink at end and inbuilt windscreen washers. NEW Price per each. $ Page B MODEL CABIN INTERIOR

31 SECTION 3 - CABIN INTERIOR ALL PRICES SUBJECT TO GST WIPER ARM MOUNTING NUTS & SPACER 177 Acorn domed retainer cap nut wiper arm assembly - new - 2 required - sold per each (Not SAE thread). B177 $ Knurled drive tapper spline on OD rectanguler hole centre adapter wiper arm - new - 2 required - sold per each. B177 $ Chrome tapped spacer - used - 2 required - sold per each. B181 $ Nut holds wiper drive to cabin - fits over chrome tapped spacer (not SAE thread) - 2 required. Sold per each Bib 162 $ WIPER CONTROL VALVE 181 Wiper control valve (4 ports with bleeder ) - used B181 $ Dash mounted wiper control knob only. B177 $ AIR OPERATED WIPER DRIVE 179 Air wiper drive motor (under dash - pre 1960) - used $ Air wiper motor - new old stock $ Page B MODEL CABIN INTERIOR

32 SECTION 3 - CABIN INTERIOR ALL PRICES SUBJECT TO GST WIPER SHAFT WITH MOUNTING 182 Pivot arm under dash with blade drives (bolts through cabin) see end shelves $ Pivot arm assembly bolts to 182 and drive motor $ MACK ORIGINAL DOOR PLATES 1242 DOOR PLATE - MACK TRUCKS INC Plainfield N.J. U.S.A. 152X76mm (SEE SECTION 7 FOR PRICING) 1243 DOOR PLATE - MACK CORPORATION New York U.S.A. 152mmx76mm. (SEE SECTION 6 I FOR PRICING) DASH PLATES 1248 DASH PLATE - CAUTION ENGINE OPERATING RANGE 95x40mm. (see section 6 I for pricing) TRUCK TRACTOR ID CONTROL PROTECTION 1247 Truck Tractor Spring Brake control lever plate with Mack logo - cut out and made lever slot. (SEE SECTION 6 I FOR PRICING) POWER DIVIDER ID CONTROL PLATE 1249 Power divider ID control plate with Mack logo, cut out and made lever slot. (SEE SECTION 6 I FOR PRICING) MACK ORIGINAL GEAR BOX NAME PLATES (see Name Plate Section for other gearbox speeds) 1215 MACK - TRO-720Q Quadruplex (20 speed overgeared) 152x65mm.(SEE SECTION 6 I FOR PRICING) 1216 MACK - 18 Speed Quadruplex Transmission - 152x65mm. (SEE SECTION 6 I FOR PRICING) Page B MODEL CABIN INTERIOR

33 SECTION 3 - CABIN INTERIOR ALL PRICES SUBJECT TO GST ALSO SEE OTHER GEAR PLATE OPTIONS - SECTION 7 GEAR SHIFT BOOT 2869 Gear shift boot rubber long 100 wide 100 high. (SEE RUBBER SECTION 6G FOR PRICING) 2868 Stainless Steel hold down surround for gear shift boot (above 2869) 2870 Gear shift boot rubber - 222mm long 135mm wide 70 high. (SEE RUBBER SECTION 6G FOR PRICING) 2871 Gear shift boot PVC high 125 wide to 18mm hole. (SEE RUBBER SECTION 6G FOR PRICING) Page B MODEL CABIN INTERIOR

34 SECTION 4 - CABIN EXTERNAL ALL PRICING IS SUBJECT TO GST CABIN SIDE AIR VENTS 300 B Model side air vent door only $ B Model side air vent sealing rubber. 700mm (27 1/2 inches) per vent. (SEE SECTION 6G FOR PRICING) 301 B Model Side air vent - mesh screen only L&R price per each. Bin 300 $ B Model side vent spring. Price per Each. They are handled. Bin 300. $ B Model side vent handle. Price Per Each. Bin 300 $ 4.55 ROOF MARKER 797 B Model original cab roof marker lights -acrylic lens - usedcondition fair to good as base plate has some rust. Rubber kit 2667 below suits this light. See General Section 6E for pricing and options. 796 B Model cab roof chrome marker lights with curved base, acrylic amber lens (5 per truck) sold per each. They are close to the original. - New - Price per each. See General Section 6E for pricing and options. 795 B Model Original glass amber lens to suit 797 marker lights - used - price per each. ROOF LIGHT ORIGINAL MOULDED EDGE TYPE RUBBER PAD 2667 Mack and other roof clearance light. Rubber glass & base pad set of 5 (10 pieces). Fit Part No. 797 used cab, very tight fit on new 796 lights. (SEE SECTION 6G FOR PRICING) B MODEL AIR HORN 486 B Model Dual ORIGINAL Grover chrome short trumpet air horns - original - (per set) with valve & fittings.600mm (24Inches long) - new. SEE SECTION 6D FOR PRICING 483 Air Horn round dual original trumpet PA 1 Grover Copy 600mm (24 inches long). Per set- suit R or B - New.SEE SECTION 6D FOR PRICING Page 31 4-B MODEL CABIN EXTERNAL

35 SECTION 4 - CABIN EXTERNAL ALL PRICING IS SUBJECT TO GST REAR WINDOW GLASS 84 Rear cab (window) toughened glass. B standard cabins only - new $ REAR WINDOW RUBBER MOULDING 2801 Rear cab (window) rubber moulding to hold glass. 3.2m (10ft6in)., (SEE SECTION 6G FOR PRICING) WINDSHIELD GLASS 81 B model windshield (windscreen) laminated auto glass - left and right are the same. 2 per truck - sold per each - new. See Door Section for Door Glass. $ WINDSCREEN (WINDSHIELD) RUBBER 2800 B model windshield rubber moulding supplied as one piece - see part 2802 for lock strip - new.(see SECTION 6G FOR PRICING) 2802 B model lock strip for windscreen (needs 4.1metres) and rear window, front and back needs 6.3 metres. Also suit R model. Sold per metre - new. (SEE SECTION 6G FOR PRICING) SUNVISOR EXTERNAL - LUND STYLE 37 B model fibreglass exterior sun visor (Lund style). Hardware not included,as it screws direct onto cabin, may require minor trimming to fit - new. $ Sunvisor steel. Original steel Australian style with mounting kit including optional centre bracket. Sunviser centre bracket - see cast parts section 7 for details. $ B MODEL (AS ORIGINAL) CORNER RUBBERS 2619 B Model Bonnet corner BUMPER rubber - 2 front & 2 Rear - sold per each - hand made to suit existing corners. Sold per each. (SEERUBBER SECTION 6G FOR PRICING) BONNET LATCH REPLACEMENT RUBBER 2847 B&R replacement rubber. Only needs small amount of trimming to fit into cup. (SEE RUBBER SECTION 6G FOR PRICING) Page 32 4-B MODEL CABIN EXTERNAL

36 SECTION 4 - CABIN EXTERNAL ALL PRICING IS SUBJECT TO GST BONNET HOOD WEB TYPE LACING - We show different options. Often the front will need a smaller size than the rear Hood lacing - 18mm x 5 x 3/16 (3/4x3/16). (SEE SECTION 6G FOR PRICING) 2691 Hood lacing - suit front cowl -1"x3/16 (25x5) sold per metre (B m, B m required). (SEE SECTION 6G FOR PRICING) 2692 Hood lacing - extra large - 30x8mm ( 1 1/4x3/8) - Suit rear cowl B Model, sold per metre, 1070mm per side, B61. Supply 2150 for cowl & 1200 for radiator cowl front 600 per side on B61. (SEE SECTION 6G FOR PRICING) BONNET HOOD LACING RUBBER 2696 Hodd lacing solid rubber 24mm wide X 5mm. Suit International, KB, and lots of other models. B Model 18 rear, 10 front. (SEE SECTION 6G FOR PRICING) T CLIPS 1455 Bonnet hood lacing T clips for convenient attachment of material to cowl and radiator shell. B Model - 18 rear, 10 front. (See Section 6C for Pricing) AIR VENT RUBBER 2563 Vent seal - fit recess B gasket. 1400mm per truck - sold per metre. (SEE SECTION 6G FOR PRICING) HEAD LIGHT PANEL MOULDING 2565 Suit head light panel to radiator - B Mack, very flexible, 7mm piping, 30mm flat section, suit many applications. Beaded vinyl moulding seals headlight panel to radiator shell and to outer mudguard. Note: Special rubber edge trim can also be used but extra work normally takes 650 per section or 2600 per truck size 40mmx10mm. (note: & 75 only need 1300) SOLD PER METRE. (SEE SECTION 6G FOR PRICING) MUDGUARD TO CAB SEAL 2685 Rubber mudguard to cabin seal. Has quarter round bead on top of strip. 1000mm Per side - size 40mmx8mm. Sold per metre. (SEE SECTION 6G FOR PRICING) Page 33 4-B MODEL CABIN EXTERNAL

37 SECTION 4 - CABIN EXTERNAL ALL PRICING IS SUBJECT TO GST OUTSIDE GRAB ENTRY HANDLE 1119 Stainless steel cabin grab handle - cast not exactly original B Model type but good look a like, same bolt pattern - length 7 inch (17.77) 1 1 inch (15mm) 210mm. - sold per each.also fit R model & Superliner. SEE SECTION 6C FOR PRICING 6 B Model stainless steel original pressed cab grab handle price per each - original type - used $ B Model stainless steel original pressed cab grab handle as above - used but rechromed. $ GRAB HANDLE SCREWS 2900 Raised old time S/S slotted head counter sunk grab handle screws. 8 per truck 1/4 x 1 UNC $ 1.55 AUSTRALIAN ROOF AIR VENT OPTION 1582 Cabin roof lift up solid top air vent - Australian option fits in top of cabin roof (very effective cooling a must for summer), 180x100 (7x4). SEE DRESS UP PARTS SECTION 6C FOR PRICING 1583 As above but larger outside dimensions - 265x214 - Cut out size 220x170. SEE DRESS UP PARTS SECTION 6C FOR PRICING. $ $ CAB MOUNTING INSULATORS 154 Mack B model special cup type cab mounting insulators, 4 large & 4 small required. They are 70mm diam & 30 high with 5/8 hole. They require 2 x 8 inch bolt at rear. See part 193 below. Sold as a set of 4. With top and bottom. (SEE SECTION 6G FOR PRICING) 193 Rear cab mounting long bolts 8" x 5/8 with washer & nyloc nuts. 2 required per each $ Cab bracket for radiator bracing rods. L&R are the same. 2 required used per each $ Page 34 4-B MODEL CABIN EXTERNAL

38 SECTION 5 - B MODEL DOOR PARTS ALL PRICING SUBJECT TO GST REBUILT DOORS NEW DOOR SKIN 97 B Model Left or right hand door shell (your old door with new skin etc) This includes full door up to lower window opening including lower mirror mounting area. Top part of door will be replaced as required. All parts will be grit blasted and light undercoat before shipment. Note - door will be as per original if cabin has been damaged we may need cabin for correct fitting. If the door inner bottom section needs replacing to make up and replace this section, new hand rolled section POA POA DOOR WINDOW REGULATOR & GEAR PLATE - NEW 91 B Model regulator gear plate Assembly (left) - new $ B Model regulator gear plate assembly (right) - new $ B Model window regulator assembly. Right - Used $ B Model regulator gear plate - Left - used $ DOOR WINDOW - REGULATOR SCISSORS - USED 368 B Model Window regulator scissors assembly (left) - used $ B Model Window regulator scissors assembly (right) - used $ DOOR WINDOW - REGULATOR SCISSORS - NEW 89 B Model Window regulator scissors assembly (left) - new $ B Model Window regulator scissors assembly (right) - NEW DOOR EDGE STRIPPING DOOR GLASS CHANNEL SUPPORT - NEW 93 Side glass support channel (fits in bottom of door window) 400mm long - left - new 94 Side glass support channel (fits in bottom of door window) 400mm long - right - new DOOR GLASS CHANNEL SUPPORT - USED 238 Side glass support channel (fits in bottom of door window) - left or right - USED DOOR GLASS 80 B Model Door side toughened auto glass - left & right are the same sold per each - new $ $ $ $ $ Page 35 5-B MODEL DOOR PARTS

39 SECTION 5 - B MODEL DOOR PARTS ALL PRICING SUBJECT TO GST DOOR WINDOW CRANK HANDLE 41 B Model window crank handle - used. 2 Per truck - sold per each 3525 B Model window crank handle - new. 2 per truck - sold per each. $ $ WINDOW STOPPER 336 Door cover plate with window stopper $ HANDLES - INNER OPENING DOOR 40 B Model Chrome inner door opening handle - used - 2 per truck sold per each 3524 B Model chrome inner cab door opening handle - new - 2 per truck sold per each $ $ DOOR & WINDOW HANDLE ESCUTCHEON 3526 B Model Door & window handle escutcheon trim rings - also suits R Model (4 per truck) sold per each -new $ B Model Door & window handle roll pins holds handles in place under 55 trim rings (4 per truck) - new Bin 3526 $ 2.15 HANDLES - OUTSIDE DOOR ENTRY 1 B Model Door Exterior Entry Turn Handles & Base Plate for rechroming (have some pitting) - used - price per each. 1A B Model entry handle as above detailed and chromed - Price per Each. (Must have exchange handle, if not add COST OF PART 1) 107 B Model door exterior entry turn handle & base plate - new $ $ POA 2900 B Model door holding screws (Note: have odbod thread), retap to 1/4 UNC, supply 2 per door. 1/4 UNCx 3/4 long counter sunk head. Bin 2900 BAILEY CHANNEL B MODEL PER DOOR KIT 2513 B Model door glass rubber channel kit. Includes flexable lining bailey channel with stainless steel bead for curved radius top of door, one rigid and one flexable for removable window panel in door and 2 sqeegee glass guides for glass to glide in. (SEE GENERAL SECTION 6G FOR PRICING) FOR OTHER WINDOW OPTIONS GLASS GUIDE CHANNEL - see Bailey Channel - Rubber Section 6G $ 1.00 Page 36 5-B MODEL DOOR PARTS

40 SECTION 5 - B MODEL DOOR PARTS ALL PRICING SUBJECT TO GST DOOR HINGE COVER PLATE 298 B Model door hinge cover plate - bolt on door to cover hinge. Bolts (4 required) not standard on all models -used - sold per each $ B MODEL DOOR HINGES 299 B Model Door hinge - top one has lug & spring - price per each - used $ DOOR STRIKER PLATE 95 Left hand striker plate (mounts on cab) - used $ Right hand striker plate (mounts on cab) - used $ CHROME PLATED STRICKER PLATE 385 Left or right stricker plate with new catch Part No 1385 detailed and chrome plated. If no exchange - add cost of 95 or 96. POA REPLACEMENT STRICKER PLATE 1385 New Replacement stricker plate catch. Plate cast from brass. L&R side supplied with stainless bolts..b95. PRICE PER EACH. Add $40 for chrome plating. Bin 385. $ DOOR WINDOW TRIM 106 B Model Inner window glass surround trim. Fits around top of door. Left or Right - Used $ USED INNER DOOR PANEL 346 B Model Door Inner Panel - no fittings Left or Right - Used $ J NUT CLIPS 2589 J speed nut, holds B model steel door trim over edge - 13 per door. Note: if door hardware kit supplied they are included with kit $ 3.65 Page 37 5-B MODEL DOOR PARTS

41 SECTION 5 - B MODEL DOOR PARTS ALL PRICING SUBJECT TO GST B MODEL DOOR LOCKS 310 B Model Door lock cab latch assembly inner fits in door LH - used $ B Model Lock cab latch door assembly inner fits in door RH - used $ B Model control assembly for door lock (remote control handle to lock L&R. It s a flat bar that goes inside door) - used $ KEY DOOR LOCKS 856 Door & ignition lock set, includes 2 door tumblers and one ignition tumbler with 2 matching keys. New. SEE SECTION 6E FOR PRICING Bin B Model door key lock assembly with shaft - used - (no key) Price Per Each. Bin 88 $ DOOR LOCK RETAINER CLIP 88 B Model Door lock slide in retainer clip. Slides from outside to hold door lock in place. - New $ DOOR SEAL RUBBER 2571 Door seal fits in cab recess to seal door with adhesive backing. 7.6m (25ft) (does 2 door openings) - sold per door.(see SECTION 6G FOR PRICING) 2560 Door seal hollow soft rubber - used on TC75. 4 metres per side. Sold per metre.works better as its softer and does not hold water but needs glueing. (SEE SECTION 6G FOR PRICING) QUARTER VENT WINDOWS QUARTER VENT GLASS 120 B Model Quarter vent window toughened auto glass - glass only bevelled edge $ QUARTER VENT HANDLES 44 Chrome die cast vent window handles only (sold per pair) - $ new. 246 Vent window handle (cast from brass) unfinished L & R - sold per each. Note: they are handed - new. Suitable for many other vehicles. Bin44 $ OPTIONAL UNIVERSAL QUARTER VENT HANDLES 712 Universal vent window handle. POA Page 38 5-B MODEL DOOR PARTS

42 SECTION 5 - B MODEL DOOR PARTS ALL PRICING SUBJECT TO GST QUARTER VENT SEALING RUBBER - SUIT B MODEL MACK - NEW 99 Quarter Vent window rubbers (pair) - fit to door to seal pivot glass closing to frame - new. Sold as pair only. (SEE SECTION 6G FOR PRICING) 99A QUARTER VENT SEALING RUBBER - SUIT B MODEL MACK - USED Quarter vent rubber complete and pliable - suit older restoration job. - Used. Price Per Each. (SEE SECTION 6G FOR PRICING) QUARTER VENT WINDOW POST SEAL 100 B model vent window post rubbers (seals glass vent to the rear upright post when glass is closed straight). Sold per each - 2 required per truck. (SEE SECTION 6G FOR PRICING) DOOR GLASS & QUARTER VENT SETTING OR GLAZING SEAL - HOLDS GLASS IN PLACE 2861 Quarter vent glass holding rubber. 400mm per B door, 700mm B Vent. Softens with kero to help fitting. When dries makes strong bond to glass. Sold per metre. Used with door glass channel lifter and quarter vent glass in its frame and some windscreen AND GLASS frames. (SEE SECTION 6G FOR PRICING) QUARTER VENT WINDOW - RECONDITIONED 76 B Model quarter vent window reconditioned and rechromed with new rubber door seal (part 99)., New post seal 100. L&R exchange service. Price per each. IF NO EXCHANGE ADD COST OF 116 BELOW. QUARTER VENT WINDOW - USED 116 Quarter vent window - used with handles. Complete L&R. Price Per Each (Subject to stock) $ $ MIRROR ARM SET - NEW 15 B Model Stainless steel Mack mirror arm SET L&R kit with rolled top to suit B doors, mirror heads are sold separate from the arms. New. $1, Page 39 5-B MODEL DOOR PARTS