TABLE OF ONTENTS YLINDER FEATURES F, O,, D, M and DM Type ylinders FLAIRLINE YLINDERS AND VALVES A Flair For Reliability, Availability, Economy and Se

Transcription

1 YLINDERS AND VALVES ATALOG FL-- FLAIRLINE FAST Shipped in - days TE LIGT-WEIGT LINE WIT EAVY-DUTY FEATURES

2 TABLE OF ONTENTS YLINDER FEATURES F, O,, D, M and DM Type ylinders FLAIRLINE YLINDERS AND VALVES A Flair For Reliability, Availability, Economy and Service 4 DOUBLE-ATING YLINDERS Series F, O, OLF, and D SINGLE-ATING YLINDERS Series FSR, OSR, SR and DSR DOUBLE-ATING DOUBLE-ENDED YLINDERS Series FDE, ODE, DE and DDE 6 TANDEM YLINDERS Series FT and DT 6 AP-TO-AP YLINDERS Series F, O, and D 6 DIMENSIONAL DATA F, O, and D Type ylinders MAGNETI SWIT YLINDERS M, DM and Digit-Air M Type ylinders 8 SWIT OPTIONS Magnetic Switch ylinders 8 DIMENSIONAL DATA M and DM Type ylinders DIMENSIONAL DATA Digit-Air M Type ylinders 0 MOUNTING AESSORIES F, O,, D, M and DM Type ylinders 0 INTERANGE SERIES I Type ylinders INTERANGE SERIES DI Type ylinders INTERANGE SERIES SI Type ylinders INTERANGE SERIES DSI Type ylinders 4 MINIATURE YLINDERS Digit-Air Type ylinders SPEIAL OPTIONS F, O,, D, M, DM, I, DI, SI and DSI Type ylinders 6 SPEIAL OPTIONS Digit-Air and Digit-Air M Type ylinders 6 MAINTENANE INSTRUTIONS F, O,, D, M, DM, I, DI, SI and DSI Type ylinders APPLIATION TIPS ylinders ORDERING INSTRUTIONS F, O,, D, I, DI, SI, DSI and Digit-Air Type ylinders 8 ORDERING INSTRUTIONS Magnetic Switch ylinders YLINDER FEATURES - NFPA INTERANGEABLE NFPA Type ylinders 0 DOUBLE-ATING YLINDERS - NFPA INTERANGEABLE Series FI, OI and OILF DOUBLE-ATING DOUBLE-ENDED YLINDERS - NFPA INTERANGEABLE Series FIDE and OIDE MAGNETI SWIT YLINDERS - NFPA INTERANGEABLE Series OIM DOUBLE-ATING NON-ROTATING YLINDERS - NFPA INTERANGEABLE Series FINR, OINR and OIMNR DIMENSIONAL DATA - NFPA INTERANGEABLE Series FI, OI, OILF, OIM, FIDE and OIDE DIMENSIONAL DATA - NFPA INTERANGEABLE Series FINR, OINR and OIMNR MOUNTING STYLES - NFPA INTERANGEABLE NFPA Type ylinders and Series V 4 MOUNTING STYLES - NFPA INTERANGEABLE NFPA Type ylinders ROD END STYLES - NFPA INTERANGEABLE Series FI, OI, OILF, OIM, FIDE and OIDE AESSORIES - NFPA INTERANGEABLE NFPA Type ylinders 6 VOLUME AMBERS Series V SPEIAL OPTIONS - NFPA INTERANGEABLE NFPA Type ylinders 8 ORDERING INSTRUTIONS - NFPA INTERANGEABLE NFPA Type ylinders and Series V EK VALVES Series V 0 FLOW ONTROLS Series RF 0 FLOW ARTS Series V and RF ORDERING INSTRUTIONS Series V and RF

3 FLAIRLINE I-YLE YLINDER FEATURES F, O,, D, M AND DM TYPE YLINDERS. hrome-plated, high-strength, steel piston rods are corrosion resistant, rugged and durable. Wrench flats behind full rod diameter threads permit easy clevis mounting.. igh-quality elastomer rod wiper protects rod seal by preventing contaminants from entering cylinder during retract stroke. Resilient synthetic rubber will not scratch rod.. Pressure-energized, U-cup type rod seal is wear compensating, low friction and provides positive sealing. 4. Extra large mounting threads and rabbets make on-the-job mounting installation fast and secure.. Lightweight aluminum heads and caps for long corrosion-resistant life. 6. Extra-long, low-friction nylon rod bearing gives rather than wears under normal side loading. When necessary, service is easy; only the bearing is replaced, not the head. Permanent bronze rod bearing is featured on D and DM type cylinders for extra side load capability.. eads and caps are held to barrel by means of a circumflex key. The large square steel locking device requires no special installation tools. Service to head or cap can be done without disassembling the entire cylinder. See page for easy maintenance details. 8. Adjustable cushions, available on bore and larger, are flush with the O.D. of the cylinder. and bores have fixed cushions.. ushion seal check valve offers fast break-away, self-aligning, positive cushioning for faster stroking and reduced cylinder wear. 0. Precision-drawn, lightweight aluminum barrels are hard-anodized inside and out for corrosion and abrasion resistance. Fine I.D. microfinish provides long life and positive sealing.. Several piston styles are offered for various application requirements. See page for F, O, and D type pistons; page 8 for M and DM type pistons.

4 FLAIRLINE YLINDERS AND VALVES A FLAIR FOR RELIABILITY, AVAILABILITY, EONOMY AND SERVIE i-ycle Means Value You can select Flairline products with confidence. They are expertly designed, made of the finest materials available, and carefully assembled. Aluminum construction for light weight, quality seals for reliability and unique features such as the uni-piston and dilating O-ring combine to give you outstanding product performance. Our design specifications are precisely held during manufacture and every individual product must pass stringent functional tests before they are considered customerready. After testing is completed, Flairline/Fast shipping assures that Flairline products are shipped to our distributors or directly to the customers within three to five working days. Flairline understands that availability is important. So is price. Flairline products are surprisingly inexpensive, rapidly repaying your low initial investment with long, troublefree operation. Quality design and easy reparability enhance production and add value to your equipment. Should Flairline cylinders and valves need service, we provide that, too. Our interest in your complete satisfaction doesn t end after the sale. With repair kits, parts and even spare cylinders available from coast to coast, Flairline is prepared to handle any emergency and minimize downtime. Make your selections with complete confidence from our extensive line of low cost, fast-action pneumatic or hydraulic cylinders and valves. Special Products Flairline standard products offer a wide variety of application capabilities. No matter how extensive a product line may be, there is often a need for something unique for your special application. Responding to this need is important to Flairline. We are pleased to offer our capabilities to manufacture cylinder and valve products to your specifications. ontact your local Flairline stocking distributor for more information. AD Files On Disk AD product drawings are available in DXF or DWG formats for use with this catalog. These drawings can also be downloaded from our Web site at 4

5 DOUBLE-ATING YLINDERS SERIES F, O, OLF, AND D F TYPE PISTON Pressure energized, wear compensating double lip type, uni-piston seal (Buna N). Rubber bonded to a plated disc to assure positive sealing, will outlast O-rings and can never score cylinder I.D. F Standard s,,,,, 4 Stock Stroke s to 8 ( increments) ushions available either/both ends Pneumatic only 0 psi maximum SINGLE-ATING YLINDERS Flairline double-acting cylinders can be used in nearly all types of applications where lightweight, economical, long-service actuators are required. Operating systems can be pneumatic or hydraulic. Low friction pneumatic service is available with Series OLF, which is designed primarily for use in low pressure applications and where low minimum breakaway is required. When side load conditions are present, select Series D with piston wear strip and bronze rod bearing. Precision components and sealing elements permit continuous operation in any environment. See page for dimensional data and page 0 for mounting accessories. For special options, see page 6. Dynamic O-ring piston seal (Buna N standard; Viton available only on Series O). Side loading will greatly reduce effectiveness of Series OLF. O/OLF Standard s,,,,, 4 Stock Stroke s to 8 ( increments) ushions available either/both ends Pneumatic 0 psi maximum ydraulic consult factory D TYPE PISTON Pressure energized, wear compensating U-cup piston seals (Buna N standard, Viton available). An acetal wear ring (bearing) prevents metal-to-metal contact when side load conditions are present. For ordering information, see page 8. O TYPE PISTON The Flairline single-acting cylinder offers the same quality, performance and features as the double-acting model. Actuated by pressurizing only one port, a spring provides the required force to return the piston rod to its normal position. Single actuation conserves energy and can minimize control valve expense. Available with F, O, or D type pistons. Please specify after series, -E for normally extended or -R for retracted. See page for dimensional data and page 0 for mounting accessories. For special options, see page 6. For ordering information, see page 8. TYPE PISTON Pressure energized, wear compensating U-cup piston seals (Buna N standard; Viton available). Standard s,,,,, 4 Stock Stroke s to 8 ( increments) ushions available either/both ends Pneumatic 0 psi maximum ydraulic consult factory D Standard s,,,,, 4 Stock Stroke s to 8 ( increments) ushions available either/both ends Pneumatic 0 psi maximum ydraulic consult factory SERIES FSR, OSR, SR AND DSR FSR OSR SR DSR Standard s to 4 to 4 to 4 to 4 Stock Stroke s ( increments) to 6 to 6 to 6 to 6 ushions available Normally extended: ead end only Normally retracted: ap end only Pneumatic 0 psi max. 0 psi max. 0 psi max. 0 psi max. ydraulic N/A consult factory consult factory consult factory

6 DOUBLE-ATING DOUBLE-ENDED YLINDERS SERIES FDE, ODE, DE AND DDE TANDEM YLINDERS AP-TO-AP YLINDERS Flairline double-acting double-ended cylinders feature F, O, or D type pistons and piston rod extensions from each end. As one end is extended, the opposite end is retracted. Working range (stroke), force and speed are equal in both directions. With both rod ends threaded and a complete line of mounting attachments available, work can be accomplished at both ends of the cylinder simultaneously. See page for dimensional data and page 0 for mounting accessories. For special options, see page 6 For ordering information, see page 8. FDE ODE DE DDE Standard s to to 4 to 4 to 4 Stock Stroke s ( increments) to 8 to 8 to 8 to 8 ushions available either/both ends either/both ends either/both ends either/both ends Pneumatic 0 psi max. 0 psi max. 0 psi max. 0 psi max. ydraulic N/A consult factory consult factory consult factory SERIES FT AND DT Tandem models consist of two cylinders joined by a common center section. An type piston (Series FT) or a D type piston (Series DT) in each cylinder is interconnected to the other by a common piston rod. Operated as two double-acting cylinders, Series FT or DT can be used to multiply force without increasing pressure or bore size. Filling the rod end cylinder with oil and using a flow control between its ports, tandems can provide the accurate speed regulation of a hydraulic cylinder while the cap end unit is operated with economical air. See page for dimensional data and page 0 for mounting accessories. For special options, see page 6. For ordering information, see page 8. FT/DT Standard s to 4 Stock Stroke s to 8 ( increments) ushions available either/both ends (cushions not standard on center head) Pneumatic 0 psi maximum ydraulic consult factory NOTE: Series FT and DT are also available in double-ended models as well as multi-position single and double-ended models. These must be quoted as specials on a per order basis. SERIES F, O,, AND D ap-to-ap models consist of two F, O, or D type cylinders joined at the cap end by a common center section. Each unit can be operated independently of the other to accurately attain and repeat three positions when both units are the same stroke and four positions when each unit is a different stroke. See page for dimensional data and page 0 for mounting accessories. For special options, see page 6. For ordering information, see page 8. F O D Standard s to 4 to 4 to 4 to 4 Stock Stroke s ( increments) to 8 to 8 to 8 to 8 ushions available either/both ends either/both ends either/both ends either/both ends of both units of both units of both units of both units Pneumatic 0 psi max. 0 psi max. 0 psi max. 0 psi max. ydraulic N/A consult factory consult factory consult factory 6

7 DIMENSIONAL DATA F, O, AND D TYPE YLINDERS DIMENSION REFERENE A B D E F G J K L M* P-NPTF YLINDER BORE DIMENSION YLINDER BORE 4 REFERENE 4 /6 /6 /6 4 /6 4 /6 R /6 S 4 /6 /6 /6 T A 4 /6 4 /6 4 /6 /6 /6 /6 /6 /6 U /6 / UT AX DIMENSION ART INLUDING STROKE LENGTS YLINDER STROKE LENGTS BORE or Over Over Over Over 4 SIZE Less to to to 4 to /6 /6 /6 / SERIES /D SERIES F/O/OLF SERIES FDE/ODE/DE/DDE SERIES FT/DT SERIES F/O//D Note: Dimensions not shown remain the same (according to bore size) as on the Series F/O/OLF drawing with the following exceptions: Series DE, DDE, and D use A dimension in place of A dimension and Series SR and DSR add to all AX dimensions.,,, 4 6 Over Over to to SERIES FSR/OSR/SR/DSR 8 0 /6 8 /6 /6 0 /6 /6 /6 8 /6 /6 0 /6 /6 /6 /6 4 /6 /6 Over to 6 6 /6 /6 *Thread size and rod diameter.

8 MAGNETI SWIT YLINDERS M, DM AND DIGIT-AIR M TYPE YLINDERS SWIT OPTIONS REED SWIT - PART NO. 4-R ALL EFFET SWIT - SOURING - PART NO. 4-P ALL EFFET SWIT - SINKING - PART NO. 4-N When automated stroke sequencing is important to you, specify Flairline magnetic switch cylinders. Standard construction includes pistons complete with a factory installed magnet which is a composite of nitrile and specifically oriented barrium ferrite particles. Flairline magnetic switch cylinders offer the quality features common to other Flairline cylinder products including: hard anodized aluminum barrels, aluminum heads and end caps, chrome-plated rods (stainless steel rods on Digit-Air M type cylinders), nylon rod bearings (bronze rod bearings on DM and Digit-Air M type cylinders) and a complete line of universal mounting accessories. Magnetic Switch options include Reed and all Effect types. Stainless steel mounting bands can be adjusted to any location on the cylinder allowing several switches to be mounted for controlling or initiating any sequence function. See pages and 0 for dimensional data and page 0 for mounting accessories. For special options, see page 6. For ordering information, see page. Other Flairline magnetic switch cylinders include: Series DIM and DIMDE on page ; Series DSIM and DSIMDE on page 4; and Series OIM and OIMNR on page. M TYPE PISTON Pressure energized, wear compensating U-cup piston seals (Buna N standard; Viton available), piston includes magnet. DM TYPE PISTON Pressure energized, wear compensating U-cup piston seals (Buna N standard), piston includes magnet. An acetal wear ring (bearing) prevents metal-to-metal contact when side load conditions are present. MAGNETI SWIT YLINDERS MOUNTING BAND - INLUDED WIT SWITES SENSOR TYPES AND TENIAL DATA Part No. Description Function Switching Voltage Switching urrent Switching Power Switching Speed Max Volt. Drop Sensitivity 4R 4P 4N Reed Switch MOV, LED alf Effect, LED Sourcing alf Effect, LED Sinking SPST Normally Open Normally Open PNP output Normally Open NPN output -0 VD/VA 0/60 z 0. Amp Max 0.00 Amp Min. 6-4 VD 0. Amp max. 6-4 VD 0. Amp max. 0 Watts Max. Watts Max. Watts Max. 0.ms operate 0.ms release.µ operate 0.µ release.µ operate 0.µ release. Volts 8 Gauss 0. Volts 8 Gauss 0. Volts 8 Gauss 8

9 DIMENSIONAL DATA M AND DM TYPE YLINDERS SERIES MSR/DMSR Single-acting ylinders Standard s,,,,, 4 Stock Stroke s to 6 ( increments) ushions available Normally extended: ead end only Normally retracted: ap end only Pneumatic 0 psi maximum ydraulic consult factory After Series, specify: -E for normally extended or -R for normally retracted SERIES MT/DMT Tandem ylinders Standard s,,,, 4 Stock Stroke s to 8 ( increments) ushions available either/both ends (cushions not standard on center head) Pneumatic 0 psi maximum ydraulic consult factory DIMENSION REFERENE A B D E F G J K L M* P-NPTF YLINDER BORE 4 4 /6 4 /6 4 /6 /6 /6 /6 /6 /6 /6 /6 / /6 /6 /6 / SERIES M/DM Double-acting ylinders Standard s,,,,, 4 Stock Stroke s to 8 ( increments) ushions available either/both ends Pneumatic 0 psi maximum ydraulic consult factory DIMENSION REFERENE R S T U UT YLINDER BORE SIZE YLINDER BORE 4 /6 4 AX DIMENSION ART INLUDING STROKE LENGTS,,, 4 or Less SERIES MDE/DMDE Double-ended ylinders Standard s,,,,, 4 Stock Stroke s to 8 ( increments) ushions available either/both ends Pneumatic 0 psi maximum ydraulic consult factory SERIES M/DM ap-to-ap ylinders Standard s,,,,, 4 Stock Stroke s to 8 ( increments) ushions available either/both ends of both units Pneumatic 0 psi maximum ydraulic consult factory NOTE: Dimensions that do not appear remain the same (according to bore size) as on the Series M/DM drawing. Series MT/DMT are also available in double-ended models as well as multi-position single and double-ended models. These must be quoted as specials on a per order basis. Over to *Thread size and rod diameter. See page 0 for mounting accessories, page 6 for special options and page for ordering information. STROKE LENGTS Over Over to to Over to /6 /6 Over to /6 /6 0 /6 /6 /6 /6 /6 0 /6 /6 /6 /6 4 /6 Over 4 to 4 /6 6 /6 Over to 6 6 /6 8 /6

10 DIMENSIONAL DATA DIGIT-AIR M TYPE YLINDERS FOR SERIES MTM & MSM DOUBLE ATING: A + STROKE FOR SERIES MTMR & MSMR SPRING RETURN: A + (STROKE X ) FOR SERIES MTMR & MSMR UP TO STROKE SPRING RETURN: A + (STROKE + ) SERIES MTM/MTMR SWIVEL MOUNT YLINDERS SERIES MSM/MSMR NOSE MOUNT YLINDERS A B D E J K L M R S T /6 /6 /6 Porting for all sizes is N.P.T.F. /6 /6 /6 /6 /6 /6 /6 MTM/MSM MTMR/MSMR Standard s,,,, Stock Stroke s ( increments) See below See below Bumpers available Either/both ends Normally extended: head end only Normally retracted cap end only Pneumatic 00 psi max. 00 psi max. ydraulic 00 psi max. 00 psi max. After Series, specify: -E for normally extended or -R for normally retracted /6-8 /6-8 /6 /6-4 NOTE: For cylinders with bumpers, contact factory for stock stroke sizes and add to Dimension A for each bumper. For cylinders with switches, contact factory for number of switches each stock stroke size can accommodate. See page 8 for magnetic switch options, page for mounting accessories, page 6 for special options and page for ordering information. MOUNTING AESSORIES --,, Mounting nut included. --,,, onnecting Pin included. FOOT BRAKET A B D E F G /6 /6 /6 /6 4 ROD LEVIS A B D E F G /6-0 /6 /6 /6-8 /6 /6 /6-4 /6 F, O,, D, M AND DM TYPE YLINDERS --,,, 4 Mounting nut included.,, FLANGE BRAKET MOUNTING NUT A B D E /6 /6 4 eight Across Flats, /6 0, -4-,, onnecting pin included. SWIVEL BRAKET A B D E F G /6 /6 /6 4 ROD NUT INLUDED ON ALL F, O,, D, M AND DM TYPE YLINDERS

11 INTERANGE SERIES I TYPE YLINDERS A B /6 /6 /6 /6 *Thread size and rod diameter D E /64 /64 /64 /6 /6 I type cylinders include Series I double-acting cylinders and Series IDE double-ended cylinders which are dimensionally interchangeable with some competitive cylinders. External dimensions may be interchanged with competitors to minimize expensive inventory or engineering changeovers. Operating systems can be pneumatic or hydraulic. Standard Series I and IDE cylinders can also provide low friction pneumatic service for use in low pressure applications and where low minimum breakaway is required. Standard construction includes O-ring pistons and many other features common to Flairline cylinder products including: hard anodized aluminum barrels, aluminum heads and end caps, chrome-plated rods, nylon rod bearings, rod wipers and a complete line of universal mounting accessories. For special options, see page 6. Standard s,,,, Stock Stroke s to 8 ( increments) ushions available either/both ends Pneumatic 0 psi maximum ydraulic consult factory DIMENSIONAL DATA F /6 /6 /6 /6 MOUNTING AESSORIES ROD LEVIS A B D E F G -- / /6 /6 / /6 /6 /6, --6 /6 /6-0 /6 /6 onnecting pin included. SERIES I SERIES IDE G -6 /6-8 / J For ordering information, see page 8. K /6 /6 /6 /6 L M* P R /6 S T /6 /6 /6 /6 MOUNTING NUT Across eight Flats -8- /6, -8-8 /6, -8-4 /6 SWIVEL BRAKET A B D E F G -4- /6, -4-4 /6 /6, -4-6 /6 4 FOOT BRAKET A B D E F G -- /64, --4 /6 /64 /6 /6, FLANGE BRAKET A B D E -- /6, --4 /6, onnecting pin included. Mounting nut included. Mounting nut included. ROD NUT INLUDED ON ALL I AND DI TYPE YLINDERS

12 INTERANGE SERIES DI TYPE YLINDERS A B /6 /6 /6 /6 *Thread size and rod diameter D E /64 /64 /64 /6 /6 DI type cylinders expand Flairline s I type cylinders by offering double U-cup pistons with wear strips and bronze rod bearings for use when side load conditions are present. External dimensions may be interchanged with competitors to minimize expensive inventory or engineering changeovers. DI type cylinders include four series: Series DI double-acting cylinders and Series DIDE double-ended cylinders provide pneumatic or hydraulic service. Standard Series DI and DIDE cylinders also offer low friction pneumatic service for use in low pressure applications and where low minimum breakaway is required. Series DIM double-acting cylinders and Series DIMDE double-ended cylinders provide pneumatic or hydraulic service and include pistons with factory installed magnets for use with magnetic switches. For automated stroke sequencing, specify Series DIM or DIMDE. See page 8 for magnetic switch options. See page for mounting accessories and page 6 for special options. Standard s,,,, Stock Stroke s to 8 ( increments) ushions available either/both ends Pneumatic 0 psi maximum ydraulic consult factory SERIES DI/DIM SERIES DIDE/DIMDE DIMENSIONAL DATA F /6 /6 /6 /6 G -6 /6-8 / For ordering information, see pages 8 and. Note: Dimensions that do not appear remain the same (according to bore size) as on the Series DI/DIM drawing. J K /6 /6 /6 /6 L M* P R /6 S T /6 /6 /6 /6

13 INTERANGE SERIES SI TYPE YLINDERS SI type cylinders are dimensionally interchangeable with some competitive cylinders. Often, those competitive cylinders not interchangeable with Flairline I type cylinders will be interchangeable with SI type cylinders. Expensive engineering or inventory changeovers may be minimized by the interchangeability of external dimensions. SI type cylinders include Series SI double-acting cylinders and Series SIDE double-ended cylinders. Operating systems can be pneumatic or hydraulic. Standard construction includes O-ring pistons and many other features common to Flairline cylinder products including: hard anodized aluminum barrels, aluminum heads and end caps, chrome-plated rods, nylon rod bearings, rod wipers and a complete line of universal mounting accessories. For special options, see page 6. Standard s,,,, Stock Stroke s to 8 ( increments) ushions available either/both ends Pneumatic 0 psi maximum ydraulic consult factory A /6 /6 /6 /6 /6 B *Thread size and Rod diameter. SWIVEL BRAKET -4-, -4-4 /6, -4-6 /6 onnecting pin included. D A B D E F G /6 E /64 /64 /64 /6 /6 DIMENSIONAL DATA F /6 /6 G ROD LEVIS /6-8 / J -6-6 A B D E F G -- / /6 /6 / /6 /6 /6, --6 /6 /6-0 /6 /6 onnecting pin included. /6 4 For ordering information, see page 8. SERIES SI SERIES SIDE FOOT BRAKET K /6 /6 /6 /6 L M* P -6 MOUNTING AESSORIES A B D E F G -- /64, AP END --4 /6 /64 /6 /6, EAD END --4A /6 /64 /6 /6, Mounting nut included. R S T /6, AP ( Dimension) -8-8, EAD ( Dimension) -8-6, MOUNTING NUT FLANGE BRAKET /6 /6 /6 /6 A B D E -- /6, AP END --4 /6, EADEND, --4A /6 Mounting nut included. eight Across Flats -8- /6-8-4 /6 /6 ROD NUT INLUDED ON ALL SI AND DSI TYPE YLINDERS

14 INTERANGE SERIES DSI TYPE YLINDERS A /6 B /6 /6 /6 /6 *Thread size and rod diameter D E /64 /64 /64 /6 /6 DSI type cylinders expand Flairline s SI type cylinders by offering double U-cup pistons with wear strips and bronze rod bearings for use when side load conditions are present. External dimensions may be interchanged with competitors to minimize expensive inventory or engineering changeovers. DSI type cylinders include four series: Series DSI double-acting cylinders and Series DSIDE double-ended cylinders provide pneumatic or hydraulic service. Series DSIM double-acting cylinders and Series DSIMDE double-ended cylinders provide pneumatic or hydraulic service and include pistons with factory installed magnets for use with magnetic switches. For automated stroke sequencing, specify Series DSIM or DSIMDE. See page 8 for magnetic switch options. See page for mounting accessories and page 6 for special options. Standard s,,,, Stock Stroke s to 8 ( increments) ushions available either/both ends Pneumatic 0 psi maximum ydraulic consult factory DIMENSIONAL DATA F /6 /6 SERIES DSI/DSIM SERIES DSIDE/DSIMDE G -6 /6-8 / For ordering information, see pages 8 and. Note: Dimensions that do not appear remain the same (according to bore size) as on the Series DSI drawing. J K /6 /6 /6 /6 L M* P R /6 S T /6 /6 /6 /6 4

15 MINIATURE YLINDERS DIGIT-AIR TYPE YLINDERS onnecting pin included. SERIES FTM/FTMR SWIVEL MOUNT YLINDERS A /6 /6 /6 B /6 /6 /6 /6 Flairline Digit-Air double-acting cylinders are inexpensive, repairable, small bore actuators. Standard construction includes: hard-anodized aluminum barrels; aluminum heads and end caps; O-ring piston and rod seals; bronze rod bearings; and stainless-steel rods. Specify Series FSM for head end nose mounting and Series FTM for cap end universal swivel mounting. The Digit-Air is also available as a single-acting, spring return cylinder (Series FTMR and FSMR). For spring return models, specify, after Series, -R for normally retracted or -E for normally extended. For special options, see page 6. For ordering information, see page 8. FTM/FSM FTMR/FSMR Standard s,,,, Stock Stroke s ( increments) to 6 to Pneumatic 00 psi max. 00 psi max. ydraulic 00 psi max. 00 psi max. Bumpers available Either/both ends Normally extended: head end only FOR SERIES FTM & FSM DOUBLE ATING: A + STROKE FOR SERIES FTMR & FSMR SPRING RETURN: A + (STROKE X ) Normally retracted cap end only FOR SERIES FTMR & FSMR UP TO STROKE SPRING RETURN: A + (STROKE + ) D /6 DIMENSIONAL DATA E /6 /6 MOUNTING AESSORIES SERIES FSM/FSMR NOSE MOUNT YLINDERS SWIVEL BRAKET FOOT BRAKET ROD LEVIS, J K /6 L M -8-8 /6-4 NOTE: For Series Digit-Air with bumpers, contact factory for stock stroke sizes and add to Dimension A for each bumper. R /6 /6 S T Porting for all sizes is N.P.T.F. A AA B D E F G J K L M N P R S T U V W X Y, /6, 6- - Mounting nut included. /6 /6 ROD NUT INLUDED ON ALL DIGIT-AIR TYPE YLINDERS /6-8 /6-4 /6, 6- - onnecting pin included.

16 SPEIAL OPTIONS F, O,, D, M, DM, I, DI, SI, AND DSI TYPE YLINDERS ushions SPEIAL OPTIONS OPTIONS Metal rod scraper (not available on I or DI type bore cylinders or any SI or DSI type cylinders Extra inlet ports head and/or cap end Tang at 0 from standard No tang (cap end includes projection for disassembly) Non-stock stroke cylinders Stainless steel circumflex keys Viton packing [not available on F type (except Series FT), low friction, cylinders or magnetic switch cylinders] Magnetic switches (available on magnetic switch cylinders) eavy duty springs (available on single-acting cylinders) Stop tubes Permanent lubrication [available on F type cylinders (except Series FT), standard on low friction cylinders] SPEIAL ROD OPTIONS Special dimension T (rod extension) Special dimension L (thread length) Special dimension M (thread size) Tapped hole in rod end Stainless steel rods Oversized rods Bumpers** Non-stock stroke cylinders OPTIONS Viton packing (not available on Digit-Air M type cylinders)** Magnetic switches (available on Digit-Air M type cylinders) Stop tubes SPEIFY AFTER STROKE:* (See pages 8 and for ordering information) MRS Extra port(s) [indicate location(s) and head and/or cap end] Tang 0 NT (See pages 8 and for ordering information) SS Keys Viton (See pages 8 and for ordering information) (Indicate specifications) (See pages 8 and for ordering information) Perm Lube SPEIFY AFTER STROKE:* T = (indicate dimension required) L = (indicate dimension required) M = (indicate thread size required or plain rod end) M = (indicate thread size and depth required) SS Rod *See pages 8 and for ordering information. (Indicate rod size required) ontact factory for sizes available. DIGIT-AIR AND DIGIT-AIR M TYPE YLINDERS SPEIFY AFTER STROKE:* (See pages 8 and for ordering information) (See pages 8 and for ordering information) Viton (See pages 8 and for ordering information) (See pages 8 and for ordering information) SPEIAL ROD OPTIONS Special dimension T (rod extension) Special dimension L (thread length) Special dimension M (thread size) SPEIFY AFTER STROKE:* T = (indicate dimension required) L = (indicate dimension required) M = (indicate thread size required or plain rod end) *See pages 8 and for ordering information. **Bumpers and Viton packing may not be compatible in some applications. 6

17 MAINTENANE INSTRUTIONS F, O,, D, M, DM, I, DI, SI AND DSI TYPE YLINDERS DISASSEMBLY, EAD END Remove any plumbing from cylinder ports; wrap barrel in heavy cloth to prevent damage to barrel. Place cap end of cylinder barrel in vise. As you rotate head counter-clockwise, use a screw driver to lift end of circumflex key clear of slot (Fig. ). ontinue rotation of head, and circumflex key will feed out of slot (Fig. ). Gripping rod, pull forward. ead, rod and piston will come out of barrel (Fig. 4). Screw head off rod threads for ease of clearing rod packing. AP END Slide head end back in barrel to support barrel and follow same procedure as above to remove circumflex key from cap end (Fig. ). If cylinder has been used in wet or moist external conditions for a long period, circumflex key may be corroded. If this is the case, apply penetrating oil into the lock slots prior to disassembly. ASSEMBLY Replace piston (if necessary), rod packings and wiper and all static seals. lean I.D. of tube thoroughly. Lubricate rod packings and O.D. of piston prior to assembly. To reassemble cylinder, follow above procedure, except heads will be turned clockwise after circumflex key is engaged in tang hole in circumflex groove of head. Turn clockwise until circumflex is completely into groove and cylinder port in head is aligned with port hole in barrel. To get head end over rod threads without damaging packing and wiper, wrap rod threads with tape. NOTE: Lock nut must be replaced when piston is replaced (Fig. 4). Do not use old lock nut. omplete packing kits and lubricants are available for all Flairline cylinders and can be ordered from your Flairline distributor. APPLIATION TIPS Applications for pneumatic cylinders are limitless. Application assistance is available from your local Flairline distributor or from the many publications that are readily available throughout the fluid power industry. Pictured below are some typical pneumatic cylinder applications. WARNING Flairline s Series F uni-piston should not be used in heavy sideload applications. When using an all rubber piston, it is possible for sideloading to cause a jamming condition. This will result in delayed actuation of the cylinder. When sideloading is necessary, contact your local Flairline distributor or the factory for alternative piston configurations. Flairline will not assume responsibility for the application of its products. NOTE: All specifications and dimensions are subject to change without notice. Figure IRUMFLEX KEY Figure IRUMFLEX KEY SLOT Figure YLINDERS Figure 4 LOK NUT Sideloading commonly occurs when misalignment, deflection or extremely long strokes are present.

18 ORDERING INSTRUTIONS F, O,, D, I, DI, SI, DSI AND DIGIT-AIR TYPE YLINDERS To order any products, specify information from categories listed below and arrange according to Example. EXAMPLE: FSR R X T = SPEIAL OPTIONS 8 Series F O OLF -D FDE ODE DE DDE FT DT F-O -D ** I-DI SI-DSI IDE DIDE SIDE DSIDE FTM FSM FSR OSR SR-DSR FTMR FSMR Normal Spring Return Mode N/A Normally Extended Normally Retracted ode Stroke ushions ode N/A E R,,,,, 4,,,,,,,, 4,,,, 4,,,,, 4,,,,,,,,,,,,, 4,,,,, 4,, to 8 * ( increments) to 8 * ( increments) to 8 * ( increments) to 8 * ( increments) to 8 * ( increments) to 6 ( increments) to 6 ( increments) to ( increments) ead only ap only Both One end only Both (Rod end unit only) ead only ap only Both ead only ap only Both One end only Both (Bumpers)*** ead only ap only Both ead only when Normally extended ap only when Normally retracted (Bumpers)*** ead only when Normally extended ap only when Normally retracted * ylinders are available in even inch increments of stroke plus, and strokes in bore sizes, and. All others (up to 0 ) are considered non-stock. Strokes over 40 may require oversized rods and/or stop tubes. **To order ap-to-ap models: EXAMPLE: F 6 T = 8 X : X Model Stroke ushions Special Options Stroke ushions Special Options ***When specifying bumpers, contact factory for stock stroke sizes. SPEIAL NOTE: WEN ORDERING A YLINDER WIT A STOP TUBE, SPEIFY TOTAL STROKE INLUDING TE STOP TUBE LENGT IN TE STROKE ATEGORY. IN TE SPEIAL OPTIONS ATEGORY, SPEIFY TE STOP TUBE LENGT. REPLAEMENT PARTS, PAKING KITS AND LUBRIANTS ARE AVAILABLE FOR ALL FLAIRLINE YLINDERS All specifications and dimensions are subject to change without notice.

19 ORDERING INSTRUTIONS MAGNETI SWIT YLINDERS To order any products, specify information from categories listed below and arrange according to Example. EXAMPLE: MSR R R X T = SPEIAL OPTIONS Series M DM MDE DMDE MT DMT M DM ** DIM DSIM DIMDE DSIMDE MTM MSM MSR DMSR MTMR MSMR Normal Spring Return Mode N/A Normally Extended Normally Retracted ode N/A E R No. of Switches Qty. Switch Model 4-R 4-P 4-N (use suffix only) Stroke ushions ode,,,,, 4,,,,, 4,,,, 4,,,,, 4,,,,,,,, to 8 * ( increments) to 8 * ( increments) to 8 * ( increments) to 8 * ( increments) to 8 * ( increments) to 8 * ( increments),, See page 0,,,,, 4 to 6 ( increments),, See page 0 ead only ap only Both One end only Both (Rod end unit only) ead only ap only Both (Rod end unit only) ead only ap only Both ead only ap only Both One end only Both (Bumpers)*** ead only ap only Both ead only when Normally extended ap only when Normally retracted (Bumpers)*** ead only ap only Both *ylinders are available in even inch increments of stroke plus, and strokes in bore sizes, and. All others (up to 0 ) are considered non-stock. Strokes over 40 may require oversized rods and/or stop tubes. **To order ap-to-ap models: EXAMPLE: M R 6 T= R 8 X : X Model No. of Switch Stroke ushions Special Options No. of Switch Stroke ushions Special Options Switches Model Switches Model ***When specifying bumpers, contact factory for stock stroke sizes. OTER FLAIRLINE MAGNETI SWIT YLINDERS INLUDE SERIES OIM AND OIMNR ON PAGE SPEIAL NOTE: WEN ORDERING A YLINDER WIT A STOP TUBE, SPEIFY TOTAL STROKE INLUDING TE STOP TUBE LENGT IN TE STROKE ATEGORY. IN TE SPEIAL OPTIONS ATEGORY, SPEIFY TE STOP TUBE LENGT. REPLAEMENT PARTS, PAKING KITS AND LUBRIANTS ARE AVAILABLE FOR ALL FLAIRLINE YLINDERS All specifications and dimensions are subject to change without notice.

20 YLINDER FEATURES NFPA INTERANGEABLE NFPA TYPE YLINDERS ONLY TE TIE RODS ARE MISSING Eliminating the tie rods means space-saving NFPA mounting, lighter weight and easy maintenance. Flairline heavy duty features provide millions of trouble-free cycles less expensively than equivalent tie rod cylinders.. hrome-plated, high-strength, steel piston rods are corrosion resistant, rugged and durable. Three NFPA rod end options are offered. Optional stainless steel is available upon request.. igh-quality elastomer rod wiper protects rod seal by preventing contaminants from entering cylinder during retract stroke. Resilient synthetic rubber will not scratch rod.. Pressure-energized, U-cup type rod seal is wear compensating, low friction and provides positive sealing Lightweight aluminum heads and caps provide long corrosion-resistant life.. Extra-long, low-friction nylon rod bearing gives rather than wears under normal side loading. When necessary, service is easy; only the bearing is replaced, not the head. 6. eads and caps are held to tube by means of a circumflex key. The large square steel locking device requires no special installation tools. Service to head or cap can be done without disassembling the entire cylinder.. Adjustable cushions, available on bore and larger, are flush with the O.D. of the cylinder. The bore has fixed cushions. 8. ushion seal check valve offers fast break-away, self-aligning, positive cushioning for faster stroking and reduced cylinder wear.. Precision-drawn, lightweight aluminum barrels are hard-anodized inside and out for corrosion and abrasion resistance. Fine I.D. microfinish provides long life and positive sealing Several piston styles are offered for various application requirements. See pages and for details. 0

21 DOUBLE-ATING YLINDERS NFPA INTERANGEABLE SERIES FI, OI AND OILF DOUBLE-ATING DOUBLE-ENDED YLINDERS Flairline double-acting NFPA interchangeable cylinders can be used in nearly all applications where lightweight, economical, long-service actuators are required. Operating systems can be pneumatic or hydraulic. Low friction, pneumatic service is available with Series OILF which is designed primarily for use on low pressure applications and where low minimum breakaway is required. See page for dimensional data, pages 4 and for mounting styles, page for rod end styles and page 6 for accessories. For special options, see page 8. F TYPE PISTON Pressure energized, wear compensating double lip type, uni-piston seal (Buna N). Rubber bonded to a plated disc to assure positive sealing, will outlast O-rings and can never score cylinder I.D. FI Standard s,,,, 4 Stock Stroke s to 8 ( increments) ushions available either/both ends Pneumatic only 0 psi maximum NFPA INTERANGEABLE For ordering information, see page. SERIES FIDE AND OIDE Flairline double-acting double-ended NFPA interchangeable cylinders feature piston rod extensions from each end and a choice of F or O type pistons. As one end is extended, the opposite end is retracted. Working range (stroke), force and speed are equal in both directions so work can be accomplished at both ends simultaneously. See page for dimensional data, pages 4 and for mounting styles, page for rod end styles and page 6 for accessories. For special options, see page 8. For ordering information, see page. O TYPE PISTON Dynamic O-ring piston seal (Buna N standard; Viton available only on Series O). Side loading will greatly reduce effectiveness of Series OILF. OI/OILF Standard s,,,, 4 Stock Stroke s to 8 ( increments) ushions available either/both ends Pneumatic 0 psi maximum ydraulic consult factory FIDE OIDE Standard s to to 4 Stock Stroke s ( increments) to 8 to 8 ushions available either/both ends either/both ends Pneumatic 0 psi max. 0 psi max. ydraulic N/A consult factory

22 MAGNETI SWIT YLINDERS NFPA INTERANGEABLE SERIES OIM DOUBLE-ATING NON-ROTATING YLINDERS FINR Standard s,, Stock Stroke s to 8 ( increments)* ushions available either/both ends** Pneumatic only 0 psi maximum Series OIM magnetic switch NFPA interchangeable double-acting cylinders provide magnetic switch service with specially designed pistons which include factory installed magnets. See page 8 for magnetic switch options including Reed and all Effect types. See page for dimensional data, pages 4 and for mounting styles, page for rod end styles and page 6 for accessories. For special options, see page 8. NFPA INTERANGEABLE For ordering information, see page. SERIES FINR, OINR AND OIMNR Series FINR, OINR and OIMNR are dimensionally interchangeable with Flairline Series FI and Series OI NFPA cylinders except for the non-rotating feature consisting of two external chrome-plated steel guide rods, guide flange (MF) and steel rod end mounting block. Flairline double-acting non-rotating cylinders feature a choice of F type pistons (Series FINR), O type pistons (Series OINR) or OIM type pistons (Series OIMNR). Series OIMNR provides magnetic switch service. See page 8 for magnetic switch options including Reed and all Effect types. See page for dimensional data, pages 4 and for mounting styles and page 6 for accessories. For special options, see page 8. OINR Standard s,, Stock Stroke s to 8 ( increments) ushions available either/both ends Pneumatic 0 psi maximum ydraulic consult factory For ordering information, see page. OIM TYPE PISTON Dynamic O-ring piston seal (Buna N), piston includes magnet. OIM Standard s,,,, 4 Stock Stroke s to 8 ( increments) ushions available either/both ends Pneumatic 0 psi maximum ydraulic consult factory OIMNR Standard s,, Stock Stroke s to 8 ( increments) ushions available either/both ends Pneumatic 0 psi maximum ydraulic consult factory *Series FINR is not recommended for stroke requirements in excess of 8.

23 DIMENSIONAL DATA NFPA INTERANGEABLE SERIES FI, OI, OILF, OIM, FIDE AND OIDE DIMENSION REFERENE A AA B DD E EE-NPTF KK DIMENSIONAL DATA YLINDER BORE * 4* SERIES FI/OI/OILF/OIM / /6-0 /6-0 / *Series FIDE not available in or 4 bore. DIMENSION REFERENE LB LD MM P P WF Y ZM NFPA INTERANGEABLE YLINDER BORE * 4* See pages 4 and for mounting styles, page for rod end styles and page 6 for accessories. For special options, see page 8 and for ordering information, see page. DIMENSION REFERENE B E E E EE-NPTF F FB YLINDER BORE LB LB SERIES FINR/OINR/OIMNR DIMENSION REFERENE MM P R TF UF UF W X SERIES FINR, OINR AND OIMNR YLINDER BORE /6 /6 /6 X Y SERIES FIDE/OIDE See pages 4 and for mounting styles and page 6 for accessories. For special options, see page 8. and for ordering information, see page.

24 MOUNTING STYLES NFPA INTERANGEABLE NFPA TYPE YLINDERS AND SERIES V FLAIRLINE NFPA INTERANGEABLE YLINDERS ARE AVAILABLE WIT YOUR OIE OF FATORY INSTALLED MOUNTINGS 4 4 FRONT FLANGE MOUNT (NFPA MF) E F FB R TF UF W Included on Series FINR, OINR and OIMNR. SIDE LUG MOUNTS (NFPA MS) E EA F /6 4 /6 SB SS SW TS 6 US XS ZB REAR FLANGE MOUNT (NFPA MF) E F FB R TF UF ZF END LUG MOUNTS (NFPA MS) E EA EB EL EO EW F /6 /6 /6 /6 /6 /6 4 4 /6 R SE Not available on Series FINR, OINR or OIMNR. 6 XE /6 /6 6 6 See pages for rod end styles and page 6 for accessories. For special options, see page 8 and for ordering information, see page. 4 For additional mounting styles, see page.

25 MOUNTING STYLES NFPA INTERANGEABLE NFPA TYPE YLINDERS FLAIRLINE NFPA INTERANGEABLE YLINDERS ARE AVAILABLE WIT YOUR OIE OF FATORY INSTALLED MOUNTINGS, 4 ROD END STYLES LEVIS MOUNT (NFPA MP) B D W L LR M MR X Pivot pin included. 4 /6 /6 /6 /6 EAD TRUNNION MOUNT (NFPA MT) 6 E LB REF- UT WF- XG Not available on Series FINR, OINR or OIMNR. SMALL MALE (NFPA SM)* A B D KK MM VF,, /6-0,4-6 *Standard on all Flairline NFPA interchangeable cylinders. When ordering, if no rod end style is specified, style SM will be supplied. Rod eye and rod clevis fit style SM. Rod nut included. NFPA INTERANGEABLE, 4 PIVOT MOUNT (NFPA MP4) D EW FL L M MR X /6 /6 /6 /6 /6 /6 See page 6 for optional pivot pin. A B D MM VF,, -0,4-4 4 AP TRUNNION MOUNT (NFPA MT) If cushions are required on cylinders with MT or MT mounts, the cushion adjustments are located in position. See page 6 for accessories and page 8 for special options. For ordering information, see. INTERMEDIATE MALE (NFPA IM)* *Optional. Rod nut included. E LB REF- UT WF- XJ SERIES FI, OI, OILF, OIM, FIDE AND OIDE See page 6 for accessories and page 8 for special options. For ordering information, see. SORT FEMALE (NFPA SF*) A B D KK MM VF,, /6-0,4-6 *Optional.

26 AESSORIES NFPA INTERANGEABLE NFPA TYPE YLINDERS,, 4-6-, ,,,4 A A B D KK /6-0 /6-6 ROD EYE* B D W DD E F FL MR R,, 4-4-, Pivot pin included. D L M BKT. PIN F, 4 PIVOT PIN FI, 4 Snap rings included. LEVIS BRAKET PIVOT PIN /6 /6 /6,, 4--, Pivot pin included. A B D E W L KK / B,, 4--, ROD LEVIS* PIVOT BRAKET D DD E F See optional pivot pin below. ALIGNMENT OUPLER* FL MR R /6 Part Max.Pull A B D E F G at Yield 4-- /6-0 0, A -0 4, /6 /6 4, A -4 /6 /6,000 Alignment couplers improve bearing and seal life by preventing excessive binding and friction caused by misalignment. Flairline alignment couplers also allow greater assembly tolerances than would typically be required which help simplify cylinder installation. Alignment couplers work equally well in push or pull applications and are available for all Flairline cylinders. *Not available on Series FINR, OINR or OIMNR. See page 8 for special options and page for ordering information. 6

27 VOLUME AMBERS SERIES V Flairline offers a wide range of volume chambers for a variety of uses. These volume chambers are constructed of lightweight aluminum caps and barrels. The barrels are hard-anodized for corrosion resistance. The optional mountings are NFPA interchangeable and are made of anodized aluminum or oxided steel. See page 4 for mounting styles. For ordering information, see page 8. Standard s,,,, 4 Stock Length s to 8 ( increments) Pneumatic 0 psi maximum ydraulic consult factory DIMENSIONAL DATA AA E DD EE LB P Y..60 #6-X -0X /6-8X X X VOLUME DATA Basic Volume (add to total). in. in 4.4 in 8.4 in. in Add per.0 inch of length. in.4 in 4. in 8.0 in. in

28 SPEIAL OPTIONS NFPA INTERANGEABLE NFPA TYPE YLINDERS ushions OPTIONS SPEIFY AFTER MOUNTING STYLE: (See page for ordering information) Metal rod scraper (not available on or 4 bore cylinders) MRS Extra inlet ports head and/or cap end Inlet ports non-standard location head and/or cap end Non-stock stroke cylinders Stainless steel circumflex keys Viton packing (available on Series OI, OIDE and OINR) Magnetic Switches (available on Series OIM and OIMNR) Stop tubes Permanent lubrication (standard on Series OILF, available on Series FI, FIDE, and FINR) *Series FINR, OINR and OIMNR - on head end: available only in position three; on cap end: available in all positions. SPEIAL ROD OPTIONS* Rod end styles Intermediate Male (NFPA IM) or Short Female (NFPA SF) Special dimension (rod extension) Special dimension A (thread length) Special dimension XX (male thread size) Tapped hole in end of rod (female thread size) Stainless steel rods *Special rod options applying to Series FINR, OINR and OIMNR include only: Special dimension and stainless steel rods. **If no rod end style is specified, Small Male (NFPA SM) will Extra port(s) [indicate location(s) and head and/or cap end]* Port(s) [indicate location(s) and head and/or cap end]* (See page for ordering information) SS Keys Viton (See page for ordering information) (See page for ordering information) Perm Lube IM or SF** SPEIFY AFTER MOUNTING STYLE: = (indicate dimension required) A = (indicate dimension required) XX = (indicate thread size required or plain rod end) XX = (indicate thread size and depth required unless otherwise specified, all other dimensions will be Short Female) SS Rod be supplied. Rod eye and rod clevis fit style SM. See pages and 6 for rod end styles and accessories. 8

29 ORDERING INSTRUTIONS NFPA INTERANGEABLE NFPA TYPE YLINDERS AND SERIES V To order any products, specify information from categories listed below and arrange according to Example. EXAMPLE: Series FI OI OILF OIM OIMNR FINR OINR FIDE OIDE V OIM R X MFI No. of Switch Switches Model N/A Qty. N/A N/A 4-R 4-P 4-N (Use suffix only) N/A Stroke ushions ode Mounting Style,,, 4,,,,, 4 to 8 * ( increments) ead Only ap Only Both One end only Both N/A SS KEYS IM SPEIAL OPTIONS** N/A MF, MF MS, MS MP, MP4 MT, MT*** MF, MS MP, MP4 MT*** MF, MS MS, MT MT*** MF, MS, MS *ylinders are available in even inch increments of stroke plus, and strokes in bore sizes and. All others (up to 0 ) are considered non-stock. Strokes over 40 may require oversized rods and/or stop tubes. **The special options in the example are stainless steel circumflex keys and rod end style - Intermediate Male (NFPA IM). ***MT and MT mounting styles not available on bore cylinders. SPEIAL NOTE: WEN ORDERING A YLINDER WIT A STOP TUBE, SPEIFY TOTAL STROKE INLUDING TE STOP TUBE LENGT IN TE STROKE ATEGORY. IN TE SPEIAL OPTIONS ATEGORY, SPEIFY TE STOP TUBE LENGT. REPLAEMENT PARTS, PAKING KITS AND LUBRIANTS ARE AVAILABLE FOR ALL FLAIRLINE YLINDERS All specifications and dimensions are subject to change without notice.

30 EK VALVES O-EK SERIES V Lightweight aluminum O-heck features a dilating O-ring as the only moving part. Quick to open, quick to close, O-heck outflows the competition, will last millions of cycles (factory tests to 0 million cycles show no discernible wear) and always provides positive sealing (no bubble leakage). Standard NPTF sizes,,, and. FLOW ONTROLS Flairline right angle flow controls incorporate O-heck as the bypass valve. RF permits full free flow in one direction, accurately metered flow in opposite direction. Standard metering needle design includes compound needle taper of and and fine adjustment stem threads (RF for example is - 6). Right angle design eliminates the need for pipe ell normally used to make 0 turn at cylinder port. Standard NPTF sizes,,, and. Adjustment knobs and panel mounting available (NPTF sizes, and only). Optional swivel connector allows direct cylinder mounting and 60 rotation for ease of installation and space saving (NPTF sizes,,, and only). 0 Model No. V- / 8 V- / 4 V- / 8 V- / V- / 4 RIGT ANGLE FLOW ONTROL SERIES RF Pipe Thread A B /6 /6 /6 /6 /6 Right Angle Flow ontrol Model RF-(NPTF) NPTF T U V W X Y Z EX -0 /6 NPTF -8 /6-8 /

31 FLOW ARTS EK VALVES AND FLOW ONTROLS SERIES V AND RF SPEIFIATIONS Operating Pressure: 0 psi Operating Temperature Range: F. Standard O-Ring Material: Buna-N (Viton available on, and NPTF models) Standard Valve Body Material: Aluminum Standard Needle Material: Brass Standard Swivel onnector Material: Zinc-Plated Steel ORDERING INSTRUTIONS EXAMPLE: SERIES O-heck Right Angle Flow ontrol ODE V RF RF PK NPTF to and to FEATURES Flairline Valves compact design add to the appearance of any type of equipment. All Flairline Valves are individually tested before they leave the factory. Tests up to 0 million cycles show no discernible wear and still perform bubble-tite. OPTIONS Knob Panel Mount Knob & Panel Mt. Swivel Swivel & Knob Swivel K P PK S SK S EK VALVES AND FLOW ONTROLS SERIES V AND RF ODE O-RINGS ODE Buna-N (Standard) Viton Buna-N (Only) Buna-N (Standard) Viton Buna-N (Only) V V All specifications and dimensions are subject to change without notice.