MULTI-STAGES SERIES MULTI-STAGES NFPA STYLE MOUNT HEAVY DUTY - HIGH FLOW NOMINAL PRESSURE -AIR 250 PSI STANDARD BORE SIZES 1.

Transcription

1 UTI-STAGES 3 SERIES UTI-STAGES NFPA STYE OUNT HEAY DUTY - HIGH FOW NOINA PRESSURE -AIR 250 PSI STANDARD ORE SIZES 1.5 THROUGH 10 STOKE UP TO 12 NFPA STYE OUNT TWO-YEAR WARRANTY

2 3 UTISTAGE YINDERS - Design features A D E F G Solid Aluminum Head & ap achined from solid aluminum bar stock (6061 T6) and black anodized for corrosion resistance. (Also available in Stainless Steel ). Piston achined from solid aluminum bar stock (6061-T6). Offers long bearing support. Hard Anodized ID Aluminum Tube (60 Rc) Provides superior wear resistance, and lower friction coefficient for maximum seal life. (Also available in Stainless Steel.) Piston Seal ip-type low friction urethane piston seals are pressure energized and wear compensating for low friction an long life (temperature: -50 to 200 F) (iton also Available up to 400 F) (all seals can be used in a non lube application) O-ring Tube End Seals Nitrile O-ring design is pressure compensated and reusable. Rod lips seal + wiper Our New Design with a real rod u-cup is completely self compensating for zero leakage at all pressures (all seals can be used in a non lube application) The New Wiper Wipes dirt out for less maintenance and longer life of the cylinder. (Urethane) (temperature: -50 to 200 F) Piston Wear Ring Nylon material is design for low friction, and to ensure minimum wear in the cylinder in side load application. Eliminates metal-to-metal contact. H I J K Rod Gland ronze gland is externally removable without cylinder disassembly for easy maintenance. Designed to provide maximum rod bearing. (Also available in Acetal) Piston Rod High Strength steel. NITROARURIZING treatment on the rod gives better corrosion-resistant properties (out performs 12-micron (.0005 in.) chromium electroplating by ratio up to 20:1.), improved wear resistance, better lubrication retention, dent resistance without induction hardening (60Rc), environmentally Friendly, no surface pitting, flaking, or hydrogen embrittlement. The finish created by the process is a lustrous black.(available in stainless steel) Tie rods orrosion resistant (Nitro carburizing), stress proof steel maintains uniform compression on tube end seals. (Available in Stainless steel) id Plate High Flow id plate with 2 orifice (vent/vaccum) ade of 6061-T6 Aluminum and lack anodized, design for resistance, and Flow in mind ( available with 2 or 3 port for external vent/vaccum or muffler). Upper Rod High Strength steel. NITROARURIZING treatment on the rod. High Flow design. umper Incorporated bumper in piston to ensure long life and noise free, design for long life, those bumper are incorporated into the piston with enough PAGE 2

3 3 UTISTAGE YINDERS - Dimensions 2 STAGES EE N.P.T.* DD TAP ROD KK FEAE THREAD A DEPTH K J 2 + (2 x STROKE) G E SQ Z2 + (2 x STROKE) 3 STAGES EE N.P.T.* DD TAP ROD KK FEAE THREAD A DEPTH K J 3 + (3 x STROKE) G E SQ Z3 + (3 x STROKE) 4 STAGES EE N.P.T.* DD TAP ROD KK FEAE THREAD A DEPTH K J 4 + (4 x STROKE) G E SQ Z4 + (4 X STROKE) ORE A E DD EE G J KK 1 1/2 3/4 1 1/8 1,43 3/8 2 1/4-28 3/8 1 1/2 1 7/ /8 5/8 2 3/4 1 1/8 1,84 3/8 2 1/2 5/ /8 1 1/2 1 7/ /8 5/8 2 1/2 3/4 1 1/8 2,19 3/8 3 5/ /8 1 1/2 1 7/ /8 5/8 3 1/4 1 1/8 1 1/2 2,78 1/2 3 3/4 3/8-24 1/2 1 3/4 1 1/4 3/ / /8 1 1/2 3,32 1/2 4 1/2 3/8-24 1/2 1 3/4 1 1/4 3/ / /8 1 1/2 4,12 1/2 5 1/2 1/2-20 1/2 1 3/4 1 1/4 3/ / /8 2 4,88 5/8 6 1/2 1/2-20 3/ / / /8 2 6,44 5/8 8 1/2 5/8-18 3/ / /8 1 2 STAGES 3 STAGES 4 STAGES ORE 2 Z2 3 Z3 4 Z4 1 1/2 5 3/8 6 3/8 7 1/8 8 1/8 8 7/8 9 7/ /8 6 3/8 7 1/8 8 1/8 8 7/8 9 7/8 2 1/2 5 5/8 6 5/8 7 1/2 8 1/2 9 3/8 10 3/8 3 1/4 6 1/4 7 5/8 8 1/4 9 5/8 10 1/4 11 5/ /4 7 5/8 8 1/4 9 5/8 10 1/4 11 5/ /4 8 1/ /8 11 1/4 12 5/ /2 9 1/ /8 12 1/2 14 1/ /4 9 3/8 10 3/ /8 PAGE 3

4 3 SERIES - Rod Thread Dimensions & Forces ROD END STYE FU AE #1F SA AE #2S STUDDED SA AE #2* * FOR 5/8 & 1 ROD, THE ROD END WI E STUDDED #2S STANDARD ARGE AE #1F FU AE #1F SA AE #2, #2S, #4 ROD DIA. A D FF KK 5/8 3/4 3/8 1/2 5/8 1/2-20 5/8-18 7/ /8 1/2 7/8 7/8 7/ / /8 1 5/8 5/8 1 3/ / / ARGE AE #1 FEAE #4 1 3/4 2 3/4 1 1/2 1 1/8 1 1/ / / /4 7/8 1 3/4 1 1/8 1 3/ /2-12 This grid is to show How much force you can get by using our 3 ultistage cylinder. All the forces are calculated with a pressure of 100 ps.i. ultistage cylinders can be use in push (extend) or Pull (retract) or oth, Stock stroke is 1, 2, 3, 4, 6, but can be ordered up to 12 stroke FORE (in pounds at 100 psi) 2 STAGES 3 STAGES 4 STAGES ORE Extend Retract Extend Retract Extend Retract 1 1/ / / ore Stage than 4 can be ordered ask your sales representative for a special quote. 10 bore also available on special request. PAGE 4

5 3 SERIES - ounting Dimensions E5 - HEAD RETANGUAR OUNT UF TF J G F (4) R E6 - AP RETANGUAR OUNT TF UF R F (4) J G F1 - HEAD FANGE OUNT W UF TF F F (4) R ORE R TF UF F E F G J W 1 1/2 1,43 2 3/4 2 3/8 5/16 1 1/8 3/8 2 3/8 1 1/2 1 5/8 5/8 2 1,84 3 3/8 4 1/8 3/8 1 1/8 3/8 2 1/2 3/8 1 1/2 1 5/8 5/8 2 1/2 2,19 3 7/8 4 5/8 3/8 1 1/8 3/8 3 3/8 1 1/2 1 5/8 5/8 3 1/4 2, /16 5 1/2 7/16 1 1/2 1/2 3 3/4 5/8 1 3/4 1 1/4 7/8 7/8 4 3,32 5 7/16 6 1/4 7/16 1 1/2 1/2 4 1/2 5/8 1 3/4 1 1/4 7/8 7/8 5 4,12 6 5/8 7 5/8 7/16 1 1/2 1/2 5 1/2 5/8 1 3/4 1 1/4 7/8 7/8 6 4,88 7 5/8 8 5/8 9/16 2 5/8 6 1/2 3/ /2 1 1 PAGE 5

6 3 SERIES- ounting Dimensions S4 - SIDE TAPPED OUNT SN + (STROKE x N STAGES) Z + (STROKE x N STAGES) XT NT TAP TK DEEP (4) TN E3 - SQUARE HEAD OUNT (ONY FOR 8, 10 & 12 ORE W F (4) R ZF + (STROKE x N STAGES) E4 - SQUARE AP OUNT (ONY FOR 8, 10 & 12 ORE R F (4) ZF + (STROKE x N STAGES) ORE SN1 SN2 SN3 NT TK TN F R W 1 1/ /4 7 1/2 1/4-20 3/8 5/ /4 7 1/2 5/ /2 7/8 2 1/2 4 1/4 6 1/8 8 3/8-16 5/8 1 1/4 3 1/4 4 5/8 6 5/8 8 5/8 1/2-13 3/4 1 1/ /8 6 5/8 8 5/8 1/2-13 3/4 2 1/ /8 7 3/8 9 5/8 5/ / /8 8 1/8 10 5/8 3/ /8 3 1/ /8 8 1/2 11 1/8 3/ /8 4 1/2 11/ /8 PAGE 6

7 3 SERIES - ounting Dimensions P1 - SHORT EIS OUNT D dia W W P1 learance Radius X + (STROKE x N STAGES) P2 - ONG EIS OUNT D dia W W P2 F XD + (STROKE x N STAGES) P4 - EYE PIOT OUNT D dia F XD + (STROKE x N STAGES) P4 2 STAGES 3 STAGES 4 STAGES ORE D W F X2 XD2 X3 XD3 X4 XD4 1 1/2 3/4 1/2 1/2 1 1/8 3/4 5/8 7 1/8 7 1/2 8 7/8 9 1/4 10 5/ /4 1/2 1/2 1 1/8 3/4 5/8 7 1/8 7 1/2 8 7/8 9 1/4 10 5/ /2 3/4 1/2 1/2 1 1/8 3/4 5/8 7 3/8 7 3/4 9 1/4 9 5/8 11 1/8 11 1/2 3 1/4 1 1/4 3/4 5/8 1 7/8 1 1/4 7/8 8 7/8 9 1/2 10 7/8 11 1/2 12 7/8 13 1/ /4 3/4 5/8 1 7/8 1 1/4 7/8 8 7/8 9 1/2 10 7/8 11 1/2 12 7/8 13 1/ /4 3/4 5/8 1 7/8 1 1/4 7/8 9 3/ /8 12 1/4 13 7/8 14 1/ /2 1 3/4 2 1/4 1 1/2 1 1/4 10 5/8 11 3/8 13 1/8 13 7/8 15 5/8 16 3/ /4 2 1/4 1 1/2 1 1/4 10 7/8 13 1/2 16 1/8 PAGE 7

8 3 SERIES- Hall Effect & Reed switches Reed switches are constructed of two overlapping ferromagnetic reeds which are sealed in a glass tube with the ends aligned and a small gap between them. When an external magnetic force is applied, the reed assumes opposite polarity, the ends of the reeds attract each other and make contact, completing the circuit. Reed switches are not recommended in sensitive areas since they can introduce electrical noise into the circuit due to bounce and vibration from mechanical closing of the reeds. Hall Effect switches are solid state switches with no moving parts. The solid state switches is activated when the silicon chip (Hall) senses a magnetic field. Since there are no moving parts, Hall effect switches can operate in sensitive areas without sending interference or noise into the circuit. Switch specifications Switch part Number Series Spec able ength Switching oltage Switching urrent Reed switch, O, ED D/A 50/60 Hz 0.5 Amp ax.005 Amp in x xx onnections 0-9ft P wire 1-8 mm Quick onnect with Pigtail (std) 3-8 mm Quick onnect Electronic Sensor, ED, Sourcing 9 ft P able Type ode 02 - Reed switches 04 - Reed switches 31 - Hall Effect PNP 32 - Hall Effect NPN Electronic Sensor, ED, Sinking 6-24 D 6-24 D 0.5 Amp ax 0.5 Amp ax Switching Power 10 Watts ax. 12 Watts ax. 12 Watts ax. Switching Speed 0.5 μs operate 0.1 μs release 1.5 μs operate 0.5 μs release 0.5 μs operate 0.1 μs release oltage Drop 3.5 olts 1.0 olts 1.0 olts Temperature Range Switch Function Shock ibration How To Order SPST Normally Open Up to 30G (11 msec.) Up to 20G (10-55 Hz) -20 to 80-4 to 176 F Normally Open PNP output Normally Open NPN output Order lamp Separatly see below Wiring Diagrams + SUPPY 6-24 D - - REED SWITH 04 - ~ SUPPY A/D + ~ RN WHT WHT OAD *OAD sourcing *OAD sinking GRN RN EETRONI SWITH 31 ED, SOURING EETRONI SWITH 32 ED, SINKING SUPPY 6-24 D + WHT RN OAD GRN quick connect switches available To Order Switch lamp Use: (no charge when ordered with switches) A clamp = 800-A clamp = clamp = A " For 1-1/8 to 2 bore For 2-1/2 to 4 bore lamp dimensions For 5 to 8 bore PAGE 8

9 3 SERIES - Accessories NFPA EIS RAKET F DD TAP E SQ RE W W Part # D PIN DIA. W DD E F RE USED WITH P /2 1/2 3/ /2 1 1/8 3/4 1/2 1 5/8 1.5, 2 & /4 5/8 1/ /2 1 7/8 1 1/4 3/4 2 9/ , 4 & /4 5/ /2 2 1/4 1 1/ /4 6, 7 & 8 D /8 1 5/ /8 1 3/8 3 13/16 8, 10 & /4 1 1/4 7/ /2 3 1/8 2 1/4 1 3/4 4 15/16 10 & 12 NFPA EYE RAKET F DD Part # D PIN DIA. DD E F RE USED WITH P1 & P2 E /2 13/32 2 1/2 1 1/8 3/4 1/2 1 5/8 1.5, 2 & 2.5 RE E /4 17/32 3 1/2 1 7/8 1 1/4 3/4 2 9/ , 4 & 5 D E SQ E /32 4 1/2 2 1/4 1 1/ /4 6, 7 & 8 E /8 21/ /8 1 3/8 3 13/16 8, 10 & 12 E /4 29/32 6 1/2 3 1/8 2 1/4 1 3/4 4 15/16 10 & 12 NFPA ROD EIS ER W W D Part # D PIN DIA. E H HEX. W ER KK R /2 1 1/2 1 1/2 1/2 7/ /4 R /4 2 3/8 1 1/4 5/8 3/4 3/ /4 E KK R /8 1 1/2 3/ /2 R /8 4 1/ /8 1 1/ /8 R /4 4 1/2 2 3/8 1 1/4 1 3/4 1 1/ /4 H R /2 2 15/16 1 1/ / /2 NFPA ROD EYE Part # A A D PIN DIA. ER KK RE-05 3/4 1 1/2 3/4 1/2 5/8 7/16-20 RE /8 2 1/16 1 1/4 3/4 7/8 3/4-16 RE /8 2 13/16 1 1/ / RE / /8 1 9/16 1 1/4-12 RE / /2 1 3/ /2-12 RE / /2 1 7/8-12 NFPA PIN -H OPTION utter pin included Part # D A D E F P-05 1/ P-07 3/ P P / P / P PAGE 9

10 3 YINDERS - How to Order EXAPE 3P2-4x10-SE4R1- is a 3 series, 4 bore, 10 stroke, 4 stages in extend Stroke, 1 in retract,clevis mount, female rod thread, with umpers ODE 3 ASI ODE 3O OERSIZE ROD 3 P2-4 x 10 - SE4R1 - #4 - ROD END OPTIONS OUNTING OPTIONS E3 E4 E5 E6 F1 P1 P2 P4 S1 S4 T1 T2 X1 X2 X3 SQUARE HEAD OUNT SQUARE AP OUNT RET. HEAD OUNT RET. AP OUNT HEAD RET. FANGE DETAH. SHORT EIS OUNT DETAH. EIS OUNT DETAH. EYE OUNT ANGE OUNT OTTO TAPOUNT HEAD TRUNNION OUNT AP TRUNNION OUNT OTH TIE RODS EXTENDED AP END TIE RODS EXTENDED HEAD END TIE RODS EXTENDED ORE 1 1/ /2 3 1/ " 12 STROKE STD ask for other strokes UTI STAGES # 1 AE, large # 1F AE, full dia. # 2 AE, small, # 2s AE, studded # 4 FEAE, STD # X SPEIA S Ex Rx Ex :Nb of stage for the Extend stroke (E4, 4 stages extend) Rx :Nb of stage for the retract stroke (R1, 1 stages Retract) To order seal kits add the prefix 3SK to the bore and rod diameter ex: 3SK ExRx and for gland kit add the prefix 3K to the rod diameter ex: 3K-1375 Pxx REx H PORT POSITION (1,2,3,4) USHION POS. (1,2,3,4) ROD EXTENSION SEAS ADE OF iton AGNETI PISTON UPER OTH ENDS UPER AP END UPER HEAD END inear Alignment ouplers Part # A D E F G H AX PU AT YIED A-250F 1/4-28 7/8 1 1/4 1/4 5/ /16 13/ A-312F 5/ /8 1 1/4 1/4 5/ /4 13/ A-375 3/8-16 7/8 1 1/4 1/4 5/ /16 13/ A-375F 3/8-24 7/8 1 1/4 1/4 5/ /16 13/ A-437F 7/ /4 2 1/2 3/4 5/8 9/16 1 1/ A-500 1/ /4 2 1/2 3/4 5/8 9/16 1 1/ A-500F 1/ /4 2 1/2 3/4 5/8 9/16 1 1/ A-625F 5/ /4 2 1/2 3/4 5/8 1/2 1 1/ A-750 3/ /4 2 5/16 5/16 1 1/8 31/32 7/8 1 1/ A-750F 3/ /4 2 5/16 5/16 1 1/8 31/32 7/8 1 1/ A-875F 7/ /4 2 5/16 5/16 1 1/8 31/32 7/8 1 1/ Starcyl s linear alignment couplers extend the bearing and seal life of your cylinders. Our couplers prevent binding and erratic movement that misalignment causes, which eventually wears down your cylinders. Not only do Starcyl couplers work equally well in push and pull applications, but they allow a greater tolerance between the cylinder center line and the mating member. * Use jam nut to lock coupler to rod when used with full diameter threads. A /2 2 15/16 1/2 1 5/8 1 3/8 1 1/4 2 1/ A-1000F /2 2 15/16 1/2 1 5/8 1 3/8 1 1/4 2 1/ A-1250F 1 1/ /2 2 15/16 1/2 1 5/8 1 3/8 1 1/4 2 1/ A-1375F 1 3/ /2 2 15/16 1/2 1 5/8 1 3/8 1 1/4 2 1/ A-1500F 1 1/ /4 4 3/8 13/16 2 1/4 1 3/4 1 1/ A-1750F 1 3/ /4 4 3/8 13/16 2 1/4 1 3/4 1 1/ A-1875F 1 7/ /4 5 7/16 11/ /4 1 7/8 3 1/ A-200F /4 5 7/16 11/ /4 1 7/8 3 1/ PAGE 10

11 3 YINDERS - NOTES PAGE 11

12 SPAE ONE STAR3 NFPA AUINU AIR YINDERS ST3R ROD OK STAR1 STAR2 SPAE SAER SPAE SAER NFPA STYE STAR4 & STAR5 UTI STAGE SPAE SAER UPGRADAE STAR6 ST4 SERIES HEAY DUTY PNEUATI ST5 SERIES EDIU DUTY HYDRAUI YOUR STARY DISTRIUTOR: HEAY DUTY Hydraulic ylinders 3000 PSI STARY YINDERS 877-STARY FAX: (630) DE08 IN ANADA: PH: FAX