Table of Contents. Lucas Nülle GmbH Page 1/36
|
|
- Juliana Lloyd
- 6 years ago
- Views:
Transcription
1 Table of Contents Table of Contents Fluid Power PBC / PEC Pneumatics and Electro-Pneumatics PBC 11 Fluid power trainer pneumatics set PBC 12 Fluid power trainer pneumatics set PEC 11 Fluid power trainer Basic Electric and Electro-Pneumatics PEC 12 Fluid power trainer Basic Electric and Electro-Pneumatics Lucas Nülle GmbH Page 1/36
2 Fluid Power PBC / PEC Pneumatics and Electro-Pneumatics PBC / PEC Pneumatics and Electro-Pneumatics Lucas Nülle GmbH Page 2/36
3 PBC 11 Fluid power trainer pneumatics set PBC 11 Fluid power trainer pneumatics set The pneumatics training set schemes is suitable for training objectives and contents for vocational and advanced professional training of technicians. It covers the fundamentals of pneumatics based on authentic industrial products. Project exercises: Direct control, single-acting cylinder, extending Direct control, single-acting cylinder, retracting Indirect control, single-acting cylinder Velocity control, single-acting cylinder Quick moving back, single-acting cylinder Direct control, double-acting cylinder with button Indirect control, double-acting cylinder Velocity control, double-acting cylinder Control of double-acting cylinders, pulse valve, 2 manual buttons Distance dependent control of double-acting cylinders, pulse valve Control of double-acting cylinders, pulse valve, 2 reflex nozzles Stop control, double-acting cylinder, 5/3 directional valve, pulling load Pressure-dependent control, 1 double-acting cylinder Time-dependent control, 1 double-acting cylinder Connection control with shuttle and two-pressure valves Signal control, 2 double-acting cylinders, without signal overlapping Sequence control, 2 double-acting cylinders, signal overlapping, roller levers with idle return Sequence control, 2 double-acting cylinders, signal overlapping, switchover valve Grafcet Lucas Nülle GmbH Page 3/36
4 Basic equipment set, consisting of: Basic equipment set, consisting of: Pos. Product name Bestell-Nr. Anz. 1 Basic pneumatic kit SE2905-1C 1 The pneumatics equipment set is designed for implementing training objectives and covering training content in industrial and commercial advanced training and applies to train the fundamentals of pneumatics using real industrial components. Single and doubleaction cylinders, 3/2-directional, 4/2-directional, 5/2-directional and 5/3-directional valves, flow-control valves, non-return valves, onedirectional flow control valves, exhaust-air restriction, quick exhaust valves, pneumatic-type amplifier, reflection nozzle, pneumatic logic valves, time delay valves. Consists of: 1 x Filter regulator 3/2-directional valve, 0.2 to 10 bar 1 x Pneumatic manifold, 6-fold 1 x Single-action cylinder, d = 25 mm, h = 50 mm 2 x Double-action cylinder, d = 25 mm, h = 100 mm 1 x Manometer 0 to 10 bar 3 x 3/2-directional valve, pushbutton 1 x 3/2-directional valve, with pushbutton, open when unactuated (NO) 1 x 5/2-directional valve, with spring-action reset, pneumatically actuated 2 x 3/2-directional, roller lever 1 x 3/2-directional valve, with spring-action reset 3 x 5/2-directional pulse valve, pneumatically actuated 1 x 5/3-directional valve, centre lock position, pneumatically actuated 1 x 3/2-directional valve, adjustable, 2 to 8 bar 1 x 2/2-directional valve, time-delayed, 2 to 30 s 1 x Shuttle valve, OR valve 2 x Dual-pressure valve, AND valve 2 x One-directional flow control valve 1 x Quick exhaust valve 1 x Load simulator d = 25 mm, h = 100 mm, m = 3.4 kg 2 x Proximity switches, pneumatic, with mount 1 x Vacuum suction grip 2 x Non-return valve, de-lockable 10 x T-connector 4 mm 20 x Sealing plugs 4 mm 10 x Noise suppressors 1 x Pipe cutter 1 x Extraction tool 20m Plastic hose 4 x 0.75, PU, black 2m Plastic hose 6.0 x 1.05, PU 4 x Storage box Lucas Nülle GmbH Page 4/36
5 2 Grooved plate 1130 x 700 x 30 mm SE2905-8A 1 Installation surface for quick assembly for exercise installations, serves the fastening of components by means of clamping connection. Advantages: Grooved plate usable on both sides Flexible fitting without tools component can be assembled rotated by 4 x 90 compact groove distance low groove width, thus optimum space utilization, horizontally, the attachment can be adjusted continuously; vertically in the grid, clearly arranged installation of the components and thus, short length of the connection pipes. Consisting of: incl. fastening Dimensions 1130x700x30 mm³ Weight: 12 kg 3 Mobile aluminium experiment stand for pneumatics and hydraulics ST7200-3W 1 High-quality, mobile experiments stand from the SybaPro range for demonstrations and experiments. Features aluminium profile legs compatible with all add-ons and extensions for the SybaPro system. Optimized for two independent work stations for pneumatics or hydraulics. The mobile experiment stand is supplied in kit form and needs to be assembled by customers themselves. Table top: Frame: Dimensions: 2 Table tops made of 3mm sheet steel, used as a tray or as table top, 380 x 1150 mm (W x D) 1 bottom tray made of 3mm sheet steel, 700 x 1150 x 30 mm Acid-resistant epoxy-resin coating, 80 µm thick (approx.), colour RAL 7047 Power supply with 6-outlet socket strip mounted underneath the table top, 2-m lead and earthed plugs 2 extruded aluminium profiles with multiple grooves 1650 x 120 x 40 mm (WxHxD) 4 extruded aluminium profiles with multiple grooves 750 x 120 x 40 mm (WxHxD) 8 equally sized grooves in extruded aluminium profiles (3 on each side and 1 each on the front and back) Grooves accommodate standard industrial mountings Space for extension of power supply duct Base made of rectangular tubing with 4 swivelling double casters, 2 of which have brakes Acid-resistant epoxy-resin coating, 80 µm thick (approx.), colour RAL 7047 Height of table top 900 mm 1250 x 1800 x 800 mm (WxHxD) Lucas Nülle GmbH Page 5/36
6 4 Compressor, low-noise SE2902-9L 1 Extremely quiet compressed air system with compressor motor, thermo switch and automatic pressure switch. Tanks made of special steel with security valve and non-return valve, master pressure gauge, condensation drain, stop valve and maintenance unit Motor output: 0.34 kw Suction capacity: 50 l/min Power consumption at 8 bars: 2.9 A Pressure: 8 bars Tank capacity: 15 l. Noise level: 40 db(a)/1m Operating voltage: 230V AC incl. tube and connection set Dimensions: 500x410x410 mm (HxWxL) Weight: 19 kg 5 Pneumatik 01 einseitig bestückt LA Aufbau, Inbetriebnahme und Test des mobilen Hydraulik- und Pneumatikversuchsstand Lucas Nülle GmbH Page 6/36
7 Additionally recommended Pos. Product name Bestell-Nr. Anz. 6 IDG3 membrane dryer with rapid coupling and filter AF20 with water trap LM Membrane dryer, a reliable, effective and cost-efficient alternative for compressed air drying. Compact and light No power supply required Built-in noise suppressor reduces noise development from venting air Non-heating and vibration-free Air filter, high-quality filter water trap Double-sided internal thread 1/4" Semi-automatic drainage High-quality 50 Micro filtering Supplies clean compressed air Replaceable filter element Compact design Lucas Nülle GmbH Page 7/36
8 Media: Pos. Product name Bestell-Nr. Anz. 7 Interactive Lab Assistant: Pneumatics SO2801-6A 1 The instructions take the form of an Interactive Lab Assistant course. This multimedia course guides students step by step through the topic of pneumatics. The fundamentals are conveyed by means of easily understood illustrations. The Interactive Lab Assistant along with the test questions make up a comprehensive experimenting environment. Features: Interactive experiment set-ups Measurements and graphics can be copied into the experiment instruction pages by drag and drop Questions with feedback and evaluation logic for progress monitoring Printable document for simple printing out of instructions and solutions CD-ROM with Labsoft browser and course software Training contents: Basic information on carrying out experiments Detailed experiment descriptions Tests of knowledge Compilation of test results Optional Accessories: Pos. Product name Bestell-Nr. Anz. 8 Wall or aluminium-profile mounting cable storage for 48 cables ST8003-8E 1 Accommodates about 48 safety measuring leads (4mm), suitable for mounting on walls or aluminium profiles Width 200 mm, 12 guide grooves for leads Adjustable height for mounting on aluminium profiles Can be mounted on the left or right Can be mounted on walls Includes 2 screws and tenon blocks Acid-resistant epoxy-resin powder coating, thickness 80 µm approx., colour RAL 7047 Lucas Nülle GmbH Page 8/36
9 9 Monitor holder for flat screen monitor of weight up to 10kg/22lb, VESA 75/100 ST8010-4L 1 Pivoting monitor holder for attachment to aluminium profiles of furniture in the SybaPro range. Allows a monitor to be placed in the optimum position so that work and experiments are less tiring. Pivoting arm with two-part joint Quick-lock for adjustment to any height on extruded aluminium profile VESA fastening 7.5 x 7.5cm Includes VESA 75 (7.5x7.5) - VESA 100 (10x10) adapter 2 Cable clips Adequate carrying capacity 10kg/22lb TFT monitor can be turned parallel to the table edge Separation can be adjusted to anywhere between 105 and 480mm Additionally included: Cable management set for installing cables along the profiles of the aluminium lab system furniture in the SybaPro range The set consists of the following: 3 Cross cable binders for front and rear grooves of aluminium profile 3 Cross cable binders for side grooves of aluminium profile 12 Cable binders 4 Aluminium cover profiles for covering and enabling wires to be run along the grooves of an aluminium profile Includes assembly instructions 10 PC holder for SybaPro experiment trolleys, height/width adjustable ST7200-5A 1 Shelf for desktop PC made of 1.5mm sheet steel punched with holes, suitable for all furniture in the SybaPro aluminium profile range Adjustable assembly height Adjustable width ( mm) Can be mounted to left or right Includes all equipment necessary for assembly (4 bolts and 4 tenon blocks) Acid-resistant epoxy-resin powder coating, 80µm thick approx., colour RAL7047 Lucas Nülle GmbH Page 9/36
10 11 Protection cover for three-level experiment trolleys ST8010-9Y 1 Dust cover for three-level experiment trolleys For protecting equipment from dust and damp For keeping equipment out of sight (the cover must not be transparent, so is therefore opaque) Colour: matt dark grey with printed LN logo in orange) Material: nylon fabric with polyurethane coating High resistant to tearing, impregnated to be washable and waterproof Lucas Nülle GmbH Page 10/36
11 PBC 12 Fluid power trainer pneumatics set PBC 12 Fluid power trainer pneumatics set The pneumatics training set schemes is suitable for training objectives and contents for vocational and advanced professional training of technicians. It covers the fundamentals of pneumatics based on authentic industrial products. Project exercises: Direct control, single-acting cylinder, extending Direct control, single-acting cylinder, retracting Direct control, double-acting cylinder with button Indirect control, double-acting cylinder Velocity control, double-acting cylinder Control of double-acting cylinders, pulse valve, 2 manual buttons Distance dependent control of double-acting cylinders, pulse valve Time-dependent control, 1 double-acting cylinder Connection control with shuttle and two-pressure valves Signal control, 2 double-acting cylinders, without signal overlapping Grafcet Lucas Nülle GmbH Page 11/36
12 Basic equipment set, consisting of: Basic equipment set, consisting of: Pos. Product name Bestell-Nr. Anz. 12 Grundbausatz Pneumatik -manuelle/pneumatische Ventile nach PAL SE2905-1D 1 The pneumatics device set for PAL exercises is suitable for implementing the learning goals and study content in technical commercial training and further education on the basics of pneumatics in accordance with PAL based on real industrial products. The device set is not specially tailored for a PAL test, which means that older tests can also be used for preparation. Consists of: 2 x Double action cylinder, d = 25 mm, h = 100 mm 1 x Single action cylinder, d = 25 mm, h = 50 mm 2 x 3/2-way directional control valve M5, push button 1 x 3/2-way directional control valve M5, toggle 3 x 3/2-way directional control valve M5, sensing roller 1 x 3/2-way directional control valve G1/8, sensing roller 1 x 3/2-way directional control valve M5, idle return roller 1 x 5/2-way directional control valve G1/8, with spring return, pneumatically operated 2 x 5/2-way directional control valve G1/8, pulse, pneumatically operated 3 x Throttle check valve G1/8 1 x Rapid exhaust valve G1/8 2 x Shuttle valve G1/8, OR 2 x Dual pressure valve M5, AND 1 x 2/2-way directional control valve, time-delayed, 2 to 30 s 2 x Proximity switch, pneumatic, with holder 1 x Pneumatic distributor, 6x with 3/2-way directional control valve, PAL 1 x 3/2-way directional control valve G1/8, push button 1 x Manometer 0 to 10 bar 1 x Filter regulator 1 x Cable channel 200 mm 1 x Cable channel 300 mm 1 x Cable channel 400 mm 1 x Cable channel 500 mm 1 x Terminal connector, 5 x, with PAL ID plate 2 x Plastic tube 4 x 0.75, PU, black, packaging unit: 10 m 1 x T plug connector, 4 mm, packaging unit: 10 1 x Angled plug connector, 4 mm, packaging unit: 10 1 x Blanking connector, 4 mm, packaging unit: 20 Lucas Nülle GmbH Page 12/36
13 13 Grooved plate 1130 x 700 x 30 mm SE2905-8A 1 Installation surface for quick assembly for exercise installations, serves the fastening of components by means of clamping connection. Advantages: Grooved plate usable on both sides Flexible fitting without tools component can be assembled rotated by 4 x 90 compact groove distance low groove width, thus optimum space utilization, horizontally, the attachment can be adjusted continuously; vertically in the grid, clearly arranged installation of the components and thus, short length of the connection pipes. Consisting of: incl. fastening Dimensions 1130x700x30 mm³ Weight: 12 kg 14 Mobile aluminium experiment stand for pneumatics and hydraulics ST7200-3W 1 High-quality, mobile experiments stand from the SybaPro range for demonstrations and experiments. Features aluminium profile legs compatible with all add-ons and extensions for the SybaPro system. Optimized for two independent work stations for pneumatics or hydraulics. The mobile experiment stand is supplied in kit form and needs to be assembled by customers themselves. Table top: Frame: Dimensions: 2 Table tops made of 3mm sheet steel, used as a tray or as table top, 380 x 1150 mm (W x D) 1 bottom tray made of 3mm sheet steel, 700 x 1150 x 30 mm Acid-resistant epoxy-resin coating, 80 µm thick (approx.), colour RAL 7047 Power supply with 6-outlet socket strip mounted underneath the table top, 2-m lead and earthed plugs 2 extruded aluminium profiles with multiple grooves 1650 x 120 x 40 mm (WxHxD) 4 extruded aluminium profiles with multiple grooves 750 x 120 x 40 mm (WxHxD) 8 equally sized grooves in extruded aluminium profiles (3 on each side and 1 each on the front and back) Grooves accommodate standard industrial mountings Space for extension of power supply duct Base made of rectangular tubing with 4 swivelling double casters, 2 of which have brakes Acid-resistant epoxy-resin coating, 80 µm thick (approx.), colour RAL 7047 Height of table top 900 mm 1250 x 1800 x 800 mm (WxHxD) Lucas Nülle GmbH Page 13/36
14 15 Compressor, low-noise SE2902-9L 1 Extremely quiet compressed air system with compressor motor, thermo switch and automatic pressure switch. Tanks made of special steel with security valve and non-return valve, master pressure gauge, condensation drain, stop valve and maintenance unit Motor output: 0.34 kw Suction capacity: 50 l/min Power consumption at 8 bars: 2.9 A Pressure: 8 bars Tank capacity: 15 l. Noise level: 40 db(a)/1m Operating voltage: 230V AC incl. tube and connection set Dimensions: 500x410x410 mm (HxWxL) Weight: 19 kg 16 Pneumatik 01 einseitig bestückt LA Aufbau, Inbetriebnahme und Test des mobilen Hydraulik- und Pneumatikversuchsstand Lucas Nülle GmbH Page 14/36
15 Additionally recommended Pos. Product name Bestell-Nr. Anz. 17 IDG3 membrane dryer with rapid coupling and filter AF20 with water trap LM Membrane dryer, a reliable, effective and cost-efficient alternative for compressed air drying. Compact and light No power supply required Built-in noise suppressor reduces noise development from venting air Non-heating and vibration-free Air filter, high-quality filter water trap Double-sided internal thread 1/4" Semi-automatic drainage High-quality 50 Micro filtering Supplies clean compressed air Replaceable filter element Compact design Lucas Nülle GmbH Page 15/36
16 Media: Pos. Product name Bestell-Nr. Anz. 18 Interactive Lab Assistant: Pneumatik nach PAL SO2801-6C 1 Die Versuchsanleitung bildet ein Interactive Lab Assistant Kurs. Dieser Multimediakurs führt Schritt für Schritt in die Thematik der Pneumatik. Grundlagen werden durch leicht verständliche Bilder vermittelt. Der Interactive Lab Assistant bildet zusammen mit dem Fragenteil eine umfangreiche Experimentierumgebung. Besonderheiten: Interaktive Versuchsaufbauten Messwerte und Grafiken können per Drag und Drop in der Versuchsanleitung gespeichert werden Fragen mit Feedback und Auswertelogik zur Wissensstandkontrolle Druckdokument zum komfortablen Ausdruck der Versuchsanleitung mit Lösungen CD-ROM mit Labsoft-Browser und Kurssoftware Lerninhalte: Grundsätzliches zur Versuchsdurchführung Ausführliche Versuchsbeschreibung Wissenstest Erzeugung des Prüfergebnisses Optional Accessories: Pos. Product name Bestell-Nr. Anz. 19 Wall or aluminium-profile mounting cable storage for 48 cables ST8003-8E 1 Accommodates about 48 safety measuring leads (4mm), suitable for mounting on walls or aluminium profiles Width 200 mm, 12 guide grooves for leads Adjustable height for mounting on aluminium profiles Can be mounted on the left or right Can be mounted on walls Includes 2 screws and tenon blocks Acid-resistant epoxy-resin powder coating, thickness 80 µm approx., colour RAL 7047 Lucas Nülle GmbH Page 16/36
17 20 Monitor holder for flat screen monitor of weight up to 10kg/22lb, VESA 75/100 ST8010-4L 1 Pivoting monitor holder for attachment to aluminium profiles of furniture in the SybaPro range. Allows a monitor to be placed in the optimum position so that work and experiments are less tiring. Pivoting arm with two-part joint Quick-lock for adjustment to any height on extruded aluminium profile VESA fastening 7.5 x 7.5cm Includes VESA 75 (7.5x7.5) - VESA 100 (10x10) adapter 2 Cable clips Adequate carrying capacity 10kg/22lb TFT monitor can be turned parallel to the table edge Separation can be adjusted to anywhere between 105 and 480mm Additionally included: Cable management set for installing cables along the profiles of the aluminium lab system furniture in the SybaPro range The set consists of the following: 3 Cross cable binders for front and rear grooves of aluminium profile 3 Cross cable binders for side grooves of aluminium profile 12 Cable binders 4 Aluminium cover profiles for covering and enabling wires to be run along the grooves of an aluminium profile Includes assembly instructions 21 PC holder for SybaPro experiment trolleys, height/width adjustable ST7200-5A 1 Shelf for desktop PC made of 1.5mm sheet steel punched with holes, suitable for all furniture in the SybaPro aluminium profile range Adjustable assembly height Adjustable width ( mm) Can be mounted to left or right Includes all equipment necessary for assembly (4 bolts and 4 tenon blocks) Acid-resistant epoxy-resin powder coating, 80µm thick approx., colour RAL7047 Lucas Nülle GmbH Page 17/36
18 22 Protection cover for three-level experiment trolleys ST8010-9Y 1 Dust cover for three-level experiment trolleys For protecting equipment from dust and damp For keeping equipment out of sight (the cover must not be transparent, so is therefore opaque) Colour: matt dark grey with printed LN logo in orange) Material: nylon fabric with polyurethane coating High resistant to tearing, impregnated to be washable and waterproof Lucas Nülle GmbH Page 18/36
19 PEC 11 Fluid power trainer Basic Electric and Electro-Pneumatics Lucas Nülle GmbH Page 19/36
20 PEC 11 Fluid power trainer Basic Electric and Electro-Pneumatics Project exercises on electropneumatics : Master control of single-acting cylinders, valve with spring return Master control of double-acting cylinders, valve with spring return Hold element control, double-acting cylinder, pulse valve, direct Operated Hold element control, double-acting cylinder, pulse valve, relay Basic circuit with AND links Basic circuit with OR links Basic circuits with electric self-holding circuits Distance dependent control, double-acting cylinder, 1 elect. position switch Distance dependent control of double-acting cylinders, pulse valve, cylinder switch Distance dependent control of double-acting cylinders, valve with spring return, cylinder switch Stop controls, double-acting cylinder, 5/3 directional valve in locked central position Time-dependent control, double-acting cylinder, pick-up delay Time-dependent control, double-acting cylinder, release time delay Pressure-dependent control, double-acting cylinder Two-hand safety control, electric Sequence control, 2 double-acting cylinders, pulse valves Sequence control, 2 double-acting cylinders, pulse valves, signal Overlapping Sequence control, 2 double-acting cylinders, spring-returned valves, step chain Sequence control, 3 double-acting cylinders, pulse valves, step chain Sequence control, 3 double-acting cylinders, spring-returned valves, step chain Grafcet Lucas Nülle GmbH Page 20/36
21 Supplement to basic set, consisting of: Supplement to basic set, consisting of: Pos. Product name Bestell-Nr. Anz. 23 Electrical extension kit SE2905-1B 1 Electropneumatics, extension device kit, based on the basic pneumatic kit, 3/2, 5/2 directional valves with electric control, cylinder switch, pressure switch and position switch. Consisting of: 1 x 3/2 directional solenoid valve, spring return 3 x 5/2 directional solenoid valve, with spring return 3 x 5/2 directional solenoid pulse valve 6 x Electric cylinder switch with adapter 1 x Electric position switch with roller lever 1 x Mechanical pressure switch 1-16 bar 1 x Sensor induktiv 1x Sensor capazitiv 1 x Double-acting cylinder d = 25 mm, H = 100 mm 1 x Throttle check valve 1 x Storage box 24 Power channel, experiment stand for pneumatics and hydraulics, 1250mm, 3HU/222PU ST8033-2F 1 Low profile power channel (console fitting) only 133mm high for 19" 3HU inserts The channel accommodates up to 222PU Base and lid made of anodised E6/EV1 extruded aluminium profiles Sides are made of painted sheet steel (colour (RAL7047) The console power channel includes a power supply bus equipped with 5-pole high power quick-release IP40 safety plugs conforming to DIN The channel can be mounted at any height between the extruded aluminium profiles of the tables Dimensions: 1150 x 133 x 230 mm (WxHxD) Weight: 10,5 kg Lucas Nülle GmbH Page 21/36
22 25 Electrical Operating Module 84PU ST8008-9K 1 Electric operating module Multi-functional, compact operating module for all basic topics and more advanced experiments from the areas of electropneumatics and electrohydraulics. Module for setting up a control system with hard-wired programming, consisting of the following: 1 Switch 4 Push-buttons 6 Relays 1 Timer relay, adjustable with delayed pick-up 1 Timer relay, adjustable with delayed release 2 Optical displays 1 Audio indicator Technical data: Maximum current capacity of contacts/digital outputs: 2 A All inputs and outputs are via 4-mm safety sockets Built-in power supply, 24 V, 5 A Dimensions: 3HU/84WU Operating voltage: 110 V-230 V, 50/60 Hz Weight: 2.5 kg 26 Electrical Operating Module Interface 84PU ST8008-9H 1 Electric operating module Multi-functional, compact operating module for all basic topics and more advanced experiments from the areas of electropneumatics and electrohydraulics. Module for connection to a PC. Valves, cylinder, limit switches and analog measurements (e.g. pressure), as well as controls and display elements can be controlled via software using virtual relays: 8 Digital sensor inputs 6 Outputs for valves 1 Connector for valve manifolds 8 Analog inputs, V 4 Analog inputs, 0/ ma USB port for connection to PC as well as LN circuit diagram editor and measuring instruments. Software allows all the variables being measured to be plotted on the PC as a function of time. Technical data: Maximum current capacity of contacts/digital outputs: 2 A All inputs and outputs are via 4-mm safety sockets Built-in power supply, 24 V, 5 A Dimensions: 3HU/84WU Operating voltage: 110 V-230 V, 50/60 Hz Weight: 2.5 kg Lucas Nülle GmbH Page 22/36
23 27 AC power panel, 230V/16A, RCD, shut-off, key switch, 42PU ST8008-3A 1 230V/50Hz AC power supply insert for supply of power and fuse protection Key switch for function enable Automatic circuit breaker, 16 A Earth leakage circuit breaker, 10 ma Emergency off push-button, turn to unlock 3 Safety sockets, L1,N, PE Indicator light Dimensions: 3HU/42WU Weight: 1.5kg 28 Socket panel unit, 2 earth pin sockets, 12PU ST8008-3X 1 Socket panel unit 2x230V, 16A to supply mains-powered devices and consumers. All sockets are connected in parallel. 2 earth contact sockets 230V, 16A Dimensions: 3HU/12PU Weight: 0.4kg 29 Pneumatik 02 Elektro LA Aufbau, Inbetriebnahme und Test des mobilen Hydraulik- und Pneumatikversuchsstand Lucas Nülle GmbH Page 23/36
24 Media: Pos. Product name Bestell-Nr. Anz. 30 Interactive Lab Assistant: Electropneumatics SO2801-6B 1 The instructions take the form of an Interactive Lab Assistant course. This multimedia course is a supplementary course which goes deeper into the subject of pneumatics. Electrical fundamentals are conveyed with the help of easily understandable illustrations. The Interactive Lab Assistant along with the test questions make up a comprehensive experimenting environment. Features: Interactive experiment set-ups Measurements and graphics can be copied into the experiment instruction pages by drag and drop Questions with feedback and evaluation logic for progress monitoring Printable document for simple printing out of instructions and solutions CD-ROM with Labsoft browser and course software Training contents: Basic information on carrying out experiments Detailed experiment descriptions Tests of knowledge Compilation of test results Accessories: Pos. Product name Bestell-Nr. Anz. 31 Safety measurement cable (4mm), 25cm/10", red SO5126-8A 15 Safety measurement lead with stackable, contact-proof 4mm plugs colour: red length: 25 cm cable cross-section 2,5 mm 2 ratings deliver: 600V CAT II, 32A Lucas Nülle GmbH Page 24/36
25 32 Safety measurement cable (4mm), 25cm/10", black SO5126-8B 15 Safety measurement lead with stackable, contact-proof 4mm plugs colour: black length: 25 cm cable cross-section 2,5 mm 2 ratings deliver: 600V CAT II, 32A 33 Safety measurement cable (4mm), 25cm/10", blue SO5126-8E 5 Safety measurement lead with stackable, ccontact-proof 4mm plugs colour: blue length: 25 cm cable cross-section 2,5 mm 2 ratings deliver: 600V CAT II, 32A 34 Safety measurement cable (4mm), 50cm/20", red SO5126-8K 5 Safety measurement lead with stackable, contact-proof 4mm plugs colour: red length: 50 cm cable cross-section 2,5 mm 2 ratings deliver: 600V CAT II, 32A Lucas Nülle GmbH Page 25/36
26 35 Safety measurement cable (4mm), 50cm/20", blue SO5126-8P 5 Safety measurement lead with stackable, contact-proof 4mm plugs Colour: blue Length: 50 cm Wire cross section 2.5 mm 2 Rating data: 600V, CAT II, 32A 36 Safety measurement cable (4mm), 100cm/40", red SO5126-8U 5 Safety measurement leads with stackable, contact-proof 4mm plugs Colour: red Length: 100 cm Wire cross-section, 2.5 mm 2 Rating: 600V, CAT II, 32A 37 Safety measurement cable (4mm), 100cm/40", blue SO5126-9A 5 Safety measurement lead with stackable, contact-proof 4mm plugs Colour: blue Length: 100 cm Wire cross-section 2.5 mm 2 Rating: 600V, CAT II, 32A Lucas Nülle GmbH Page 26/36
27 Optional Accessories: Pos. Product name Bestell-Nr. Anz. 38 Wall or aluminium-profile mounting cable storage for 48 cables ST8003-8E 1 Accommodates about 48 safety measuring leads (4mm), suitable for mounting on walls or aluminium profiles Width 200 mm, 12 guide grooves for leads Adjustable height for mounting on aluminium profiles Can be mounted on the left or right Can be mounted on walls Includes 2 screws and tenon blocks Acid-resistant epoxy-resin powder coating, thickness 80 µm approx., colour RAL Monitor holder for flat screen monitor of weight up to 10kg/22lb, VESA 75/100 ST8010-4L 1 Pivoting monitor holder for attachment to aluminium profiles of furniture in the SybaPro range. Allows a monitor to be placed in the optimum position so that work and experiments are less tiring. Pivoting arm with two-part joint Quick-lock for adjustment to any height on extruded aluminium profile VESA fastening 7.5 x 7.5cm Includes VESA 75 (7.5x7.5) - VESA 100 (10x10) adapter 2 Cable clips Adequate carrying capacity 10kg/22lb TFT monitor can be turned parallel to the table edge Separation can be adjusted to anywhere between 105 and 480mm Additionally included: Cable management set for installing cables along the profiles of the aluminium lab system furniture in the SybaPro range The set consists of the following: 3 Cross cable binders for front and rear grooves of aluminium profile 3 Cross cable binders for side grooves of aluminium profile 12 Cable binders 4 Aluminium cover profiles for covering and enabling wires to be run along the grooves of an aluminium profile Includes assembly instructions Lucas Nülle GmbH Page 27/36
28 40 PC holder for SybaPro experiment trolleys, height/width adjustable ST7200-5A 1 Shelf for desktop PC made of 1.5mm sheet steel punched with holes, suitable for all furniture in the SybaPro aluminium profile range Adjustable assembly height Adjustable width ( mm) Can be mounted to left or right Includes all equipment necessary for assembly (4 bolts and 4 tenon blocks) Acid-resistant epoxy-resin powder coating, 80µm thick approx., colour RAL Protection cover for three-level experiment trolleys ST8010-9Y 1 Dust cover for three-level experiment trolleys For protecting equipment from dust and damp For keeping equipment out of sight (the cover must not be transparent, so is therefore opaque) Colour: matt dark grey with printed LN logo in orange) Material: nylon fabric with polyurethane coating High resistant to tearing, impregnated to be washable and waterproof Lucas Nülle GmbH Page 28/36
29 PEC 12 Fluid power trainer Basic Electric and Electro-Pneumatics PEC 12 Fluid power trainer Basic Electric and Electro-Pneumatics Project exercises on electropneumatics : Master control of single-acting cylinders, valve with spring return Master control of double-acting cylinders, valve with spring return Hold element control, double-acting cylinder, pulse valve, direct Operated Basic circuit with AND links Basic circuit with OR links Basic circuits with electric self-holding circuits Distance dependent control, double-acting cylinder, 1 elect. position switch Distance dependent control of double-acting cylinders, valve with spring return, cylinder switch Time-dependent control, double-acting cylinder, pick-up delay Time-dependent control, double-acting cylinder, release time delay Sequence control, 2 double-acting cylinders, pulse valves, signal Overlapping Grafcet Lucas Nülle GmbH Page 29/36
30 Supplement to basic set, consisting of: Supplement to basic set, consisting of: Pos. Product name Bestell-Nr. Anz. 42 Erweiterungssatz: Pneumatik -elektrische Ventile nach PAL SE2905-1E 1 The expanded device set for PAL exercises is suitable for implementing the learning goals and study content in technical commercial training and further education on electro-pneumatics in accordance with PAL based on real industrial products. The device set is not specially tailored for a PAL test, which means that older tests can also be used for preparation. The device set SE2905-1D is required as a basis. Consists of: 3 x Cylinder switch with holder 1 x 3/2-way directional control valve, electrically operated, M5, with spring return 2 x 5/2-way directional control valve, electrically operated, G1/8, with spring return 2 x 5/2-way directional control valve, electrically operated, G1/8, pulse 1 x Electrical position sensor with roller lever 43 Power channel, experiment stand for pneumatics and hydraulics, 1250mm, 3HU/222PU ST8033-2F 1 Low profile power channel (console fitting) only 133mm high for 19" 3HU inserts The channel accommodates up to 222PU Base and lid made of anodised E6/EV1 extruded aluminium profiles Sides are made of painted sheet steel (colour (RAL7047) The console power channel includes a power supply bus equipped with 5-pole high power quick-release IP40 safety plugs conforming to DIN The channel can be mounted at any height between the extruded aluminium profiles of the tables Dimensions: 1150 x 133 x 230 mm (WxHxD) Weight: 10,5 kg Lucas Nülle GmbH Page 30/36
31 44 Electrical Operating Module 84PU ST8008-9K 1 Electric operating module Multi-functional, compact operating module for all basic topics and more advanced experiments from the areas of electropneumatics and electrohydraulics. Module for setting up a control system with hard-wired programming, consisting of the following: 1 Switch 4 Push-buttons 6 Relays 1 Timer relay, adjustable with delayed pick-up 1 Timer relay, adjustable with delayed release 2 Optical displays 1 Audio indicator Technical data: Maximum current capacity of contacts/digital outputs: 2 A All inputs and outputs are via 4-mm safety sockets Built-in power supply, 24 V, 5 A Dimensions: 3HU/84WU Operating voltage: 110 V-230 V, 50/60 Hz Weight: 2.5 kg 45 Electrical Operating Module Interface 84PU ST8008-9H 1 Electric operating module Multi-functional, compact operating module for all basic topics and more advanced experiments from the areas of electropneumatics and electrohydraulics. Module for connection to a PC. Valves, cylinder, limit switches and analog measurements (e.g. pressure), as well as controls and display elements can be controlled via software using virtual relays: 8 Digital sensor inputs 6 Outputs for valves 1 Connector for valve manifolds 8 Analog inputs, V 4 Analog inputs, 0/ ma USB port for connection to PC as well as LN circuit diagram editor and measuring instruments. Software allows all the variables being measured to be plotted on the PC as a function of time. Technical data: Maximum current capacity of contacts/digital outputs: 2 A All inputs and outputs are via 4-mm safety sockets Built-in power supply, 24 V, 5 A Dimensions: 3HU/84WU Operating voltage: 110 V-230 V, 50/60 Hz Weight: 2.5 kg Lucas Nülle GmbH Page 31/36
32 46 AC power panel, 230V/16A, RCD, shut-off, key switch, 42PU ST8008-3A 1 230V/50Hz AC power supply insert for supply of power and fuse protection Key switch for function enable Automatic circuit breaker, 16 A Earth leakage circuit breaker, 10 ma Emergency off push-button, turn to unlock 3 Safety sockets, L1,N, PE Indicator light Dimensions: 3HU/42WU Weight: 1.5kg 47 Socket panel unit, 2 earth pin sockets, 12PU ST8008-3X 1 Socket panel unit 2x230V, 16A to supply mains-powered devices and consumers. All sockets are connected in parallel. 2 earth contact sockets 230V, 16A Dimensions: 3HU/12PU Weight: 0.4kg 48 Pneumatik 02 Elektro LA Aufbau, Inbetriebnahme und Test des mobilen Hydraulik- und Pneumatikversuchsstand Lucas Nülle GmbH Page 32/36
33 Media: Pos. Product name Bestell-Nr. Anz. 49 Interactive Lab Assistant: Elektro Pneumatik nach PAL SO2801-6D 1 Die Versuchsanleitung bildet ein Interactive Lab Assistant Kurs. Dieser Multimediakurs führt Schritt für Schritt in die Thematik der Pneumatik. Grundlagen werden durch leicht verständliche Bilder vermittelt. Der Interactive Lab Assistant bildet zusammen mit dem Fragenteil eine umfangreiche Experimentierumgebung. Besonderheiten: Interaktive Versuchsaufbauten Messwerte und Grafiken können per Drag und Drop in der Versuchsanleitung gespeichert werden Fragen mit Feedback und Auswertelogik zur Wissensstandkontrolle Druckdokument zum komfortablen Ausdruck der Versuchsanleitung mit Lösungen CD-ROM mit Labsoft-Browser und Kurssoftware Lerninhalte: Grundsätzliches zur Versuchsdurchführung Ausführliche Versuchsbeschreibung Wissenstest Erzeugung des Prüfergebnisses Accessories: Pos. Product name Bestell-Nr. Anz. 50 Safety measurement cable (4mm), 25cm/10", red SO5126-8A 15 Safety measurement lead with stackable, contact-proof 4mm plugs colour: red length: 25 cm cable cross-section 2,5 mm 2 ratings deliver: 600V CAT II, 32A Lucas Nülle GmbH Page 33/36
34 51 Safety measurement cable (4mm), 25cm/10", black SO5126-8B 15 Safety measurement lead with stackable, contact-proof 4mm plugs colour: black length: 25 cm cable cross-section 2,5 mm 2 ratings deliver: 600V CAT II, 32A 52 Safety measurement cable (4mm), 25cm/10", blue SO5126-8E 5 Safety measurement lead with stackable, ccontact-proof 4mm plugs colour: blue length: 25 cm cable cross-section 2,5 mm 2 ratings deliver: 600V CAT II, 32A 53 Safety measurement cable (4mm), 50cm/20", red SO5126-8K 5 Safety measurement lead with stackable, contact-proof 4mm plugs colour: red length: 50 cm cable cross-section 2,5 mm 2 ratings deliver: 600V CAT II, 32A Lucas Nülle GmbH Page 34/36
35 54 Safety measurement cable (4mm), 50cm/20", blue SO5126-8P 5 Safety measurement lead with stackable, contact-proof 4mm plugs Colour: blue Length: 50 cm Wire cross section 2.5 mm 2 Rating data: 600V, CAT II, 32A 55 Safety measurement cable (4mm), 100cm/40", red SO5126-8U 5 Safety measurement leads with stackable, contact-proof 4mm plugs Colour: red Length: 100 cm Wire cross-section, 2.5 mm 2 Rating: 600V, CAT II, 32A 56 Safety measurement cable (4mm), 100cm/40", blue SO5126-9A 5 Safety measurement lead with stackable, contact-proof 4mm plugs Colour: blue Length: 100 cm Wire cross-section 2.5 mm 2 Rating: 600V, CAT II, 32A Lucas Nülle GmbH Page 35/36
36 Optional Accessories: Pos. Product name Bestell-Nr. Anz. 57 Wall or aluminium-profile mounting cable storage for 48 cables ST8003-8E 1 Accommodates about 48 safety measuring leads (4mm), suitable for mounting on walls or aluminium profiles Width 200 mm, 12 guide grooves for leads Adjustable height for mounting on aluminium profiles Can be mounted on the left or right Can be mounted on walls Includes 2 screws and tenon blocks Acid-resistant epoxy-resin powder coating, thickness 80 µm approx., colour RAL Monitor holder for flat screen monitor of weight up to 10kg/22lb, VESA 75/100 ST8010-4L 1 Pivoting monitor holder for attachment to aluminium profiles of furniture in the SybaPro range. Allows a monitor to be placed in the optimum position so that work and experiments are less tiring. Pivoting arm with two-part joint Quick-lock for adjustment to any height on extruded aluminium profile VESA fastening 7.5 x 7.5cm Includes VESA 75 (7.5x7.5) - VESA 100 (10x10) adapter 2 Cable clips Adequate carrying capacity 10kg/22lb TFT monitor can be turned parallel to the table edge Separation can be adjusted to anywhere between 105 and 480mm Additionally included: Cable management set for installing cables along the profiles of the aluminium lab system furniture in the SybaPro range The set consists of the following: 3 Cross cable binders for front and rear grooves of aluminium profile 3 Cross cable binders for side grooves of aluminium profile 12 Cable binders 4 Aluminium cover profiles for covering and enabling wires to be run along the grooves of an aluminium profile Includes assembly instructions Lucas Nülle GmbH Page 36/36
37 59 PC holder for SybaPro experiment trolleys, height/width adjustable ST7200-5A 1 Shelf for desktop PC made of 1.5mm sheet steel punched with holes, suitable for all furniture in the SybaPro aluminium profile range Adjustable assembly height Adjustable width ( mm) Can be mounted to left or right Includes all equipment necessary for assembly (4 bolts and 4 tenon blocks) Acid-resistant epoxy-resin powder coating, 80µm thick approx., colour RAL Protection cover for three-level experiment trolleys ST8010-9Y 1 Dust cover for three-level experiment trolleys For protecting equipment from dust and damp For keeping equipment out of sight (the cover must not be transparent, so is therefore opaque) Colour: matt dark grey with printed LN logo in orange) Material: nylon fabric with polyurethane coating High resistant to tearing, impregnated to be washable and waterproof Lucas Nülle GmbH Page 37/36
Table of Contents. Table of Contents Pneumatik / Hydraulik
Table of Contents Table of Contents Pneumatik / Hydraulik Pneumatics with UniTrain Hydraulics with UniTrain PBC / PEC Pneumatics and Electro-Pneumatics PBC Fluid power trainer pneumatics set PBC 2 Fluid
More informationTable of Contents. Table of Contents UniTrain UniTrain courses UniTrain mechatronic courses IMS 23/24 with 3/4 subsystems
Table of Contents Table of Contents UniTrain UniTrain courses UniTrain mechatronic courses IMS 23/24 with 3/4 subsystems 1 2 2 3 4 Lucas Nülle GmbH Page 1/16 www.lucas-nuelle.com UniTrain UniTrain is a
More informationTable of Contents. 95 IMS 25 flexible manufacturing line with 5 stations. 104 IMS 26 flexible manufacturing line with 6 stations
Table of Contents Table of Contents Automation Technology IMS Industrial mechatronics system Mechatronics Sub-Systems with UniTrain-I IMS 1.2: DC transport system IMS 1.3: AC transport system IMS 3 Sorting
More informationTable of Contents. Lucas Nülle GmbH Page 1/7
Table of Contents Table of Contents Power Electronics / Electrical Machines / Drive Technology EEM Electrical machines 1kW EEM 5-1 Synchronous machines and mains synchronisation; reluctance machines 1kW
More informationTraining Systems for Pneumatics R /
Training Systems for Pneumatics R999000218 /11.2015 2 Training Systems for Pneumatics Training Systems for Pneumatics Drive & Control Academy 4 Training systems pneumatics 8 Device sets 10 Study topics
More informationTable of Contents. Table of Contents Electrical Power Engineering Renewable Energies EWG 2 Small wind power plant trainer
Table of Contents Table of Contents Electrical Power Engineering Renewable Energies EWG 2 Small wind power plant trainer 1 2 2 4 Lucas Nülle GmbH Page 1/23 www.lucas-nuelle.us Electrical Power Engineering
More informationTable of Contents. Lucas Nülle GmbH Page 1/7
Table of Contents Table of Contents Electrical Power Engineering, Smart Grid Trainers "Micro Grid Trainer" - Control of stand-alone networks Supplementary to EMG 2 EPH 3 Professional Photovoltaics EPH
More informationADVANCED CUSTOMIZED ELECTRO PNEUMATIC TRAINER (PRODUCT CODE: SAP 20B)
The Advanced Customized Electro Pneumatic Trainer (SAP 20B) is capable of being used to demonstrate the design, construction and application of electro-pneumatic components and circuits. Objectives:- The
More informationSuggested list for the Hydraulic and Pneumatic lab Instruments Mechatronics Engineering Department School of Applied Technical Science
Suggested list for the Hydraulic and Pneumatic lab Instruments Mechatronics Engineering Department School of Applied Technical Science Pneumatic and Electro-pneumatic components: No. EQUIPMENTS operating
More informationSAP E & C ADVANCED CUSTOMIZED ELECTRO PNEUMATIC TRAINER (FOR ITI) (PRODUCT CODE: SAP 20B-I)
The Advanced Customized Electro Pneumatic Trainer (SAP 20B-I) is capable of being used to demonstrate the design, construction and application of electro-pneumatic components and circuits. Objectives:-
More informationPneumatics Electropneumatics
Training systems for basic and future oriented education in natural science and engineering Pneumatics Electropneumatics Experimental Panel and Module System 07 / 2003 Contents Experimental panel system..........................
More informationSubject: Pneumatic Training Kit with portable Air Compressor
MSME TOOL ROOM: HYDERABAD (CENTRAL INSTITUTE OF TOOL DESIGN) Balanagar, Hyderabad 500 037 TEL.NO.23772747, 23776168 FAX No.0-4023772658 E-mail:citdpurchase@citdindia.org Visit us: www.citdindia.org. TENDER
More informationBASIC PNEUMATIC & ELECTROPNEUMATIC TRAINING SYSTEM
BASIC PNEUMATIC & ELECTROPNEUMATIC TRAINING SYSTEM UCTECH has designed a comprehensive range of specialised training packages and products for pneumatic and electro-pneumatic training using well-known
More informationPNEUTRAINER-200 Pneumatics - Electro-pneumatics
PNEUTRAINER-200 Pneumatics - Electro-pneumatics End-to-end solution for training in pneumatics and electro-pneumatics. www.smctraining.com training@smctraining.com 46 Develop the SKILLS... Analysis Troubleshooting
More informationPNEUTRAINER-400 Pneumatics - Electropneumatics
PNEUTRAINER-400 Pneumatics - Electropneumatics End-to-end solution for training in pneumatics and electro-pneumatics SMC industrial systems components on panel mounting plate Implements and controls pneumatic
More informationADJUSTED TO SITUATION AND SPACE
ADJUSTED TO SITUATION AND SPACE The is a modern, single-column equipment cart with a maximum load of up to 65 kg/143 lbs. This compact equipment cart has a modular configuration, which can be equipped
More informationLearning System for Automation and Communications. Electropneumatics. Workbook Basic Level S1 K1 K1 Y1
Learning System for Automation and Communications Electropneumatics Workbook Basic Level 1 2 3 S1 K1 K1 S2 K1 094005 Order no. 094005 Description: TEACHW.E-PNEUM. Designation: D.S201-C-GB Edition: 08/1993
More informationZ1 B1 B2 Z2 B3 B4. Steuerteil + 24 V. Leistungsteil K1 K2 K1 K2. Practice for Professionals Electropneumatics Trainee s manual. Version 1.
04 Z1 B1 B2 04 Z2 B3 B4 31 14 Y1 12 4 2 5 3 1 15 31 14 Y2 12 4 2 5 3 1 15 Steuerteil + 24 V B1 S0 K1 B2 K2 B4 K3 B3 Leistungsteil 1 2 3 4 5 6 7 8 9 K4 K1 K2 0V K1 K2 K1 K3 K2 K4 K3 Y1 K3 Y2 Practice for
More informationHybrid and Electric Vehicles
Lucas Nülle is proudly and exclusively represented in Australia and New Zealand by Better Learning Outcomes Training Systems Australia A Division of Pullman Learning Group 300 Centre Road, Bentleigh, Victoria,
More information6081 Pneumatics Training System
6081 Pneumatics Training System LabVolt Series Datasheet Festo Didactic en 220 V - 50 Hz 03/2018 Table of Contents General Description 2 Innovative design 3 Virtual Laboratory Equipment 3 Courseware 3
More informationElectro Pneumatic Workbench Scientech 2470
Scientech 2470 Electro Pneumatic Workbench is designed to demonstrate the design, construction and application of Pneumatic components and circuits. It integrates PLC technology to build Hybrid Industrial
More informationElectrohydraulics Advanced Level Workbook TP 602
Electrohydraulics Advanced Level Workbook TP 602 Festo Didactic 094471 en Authorised applications and liability The Learning System for Automation and Communication has been developed and prepared exclusively
More informationWorkspace and storage furnishings
LISTA Compact Workspace and storage furnishings Universal superstructures Utmost stability load capacities up to 10 kg Tremendous design diversity through a wide range of add-on elements including power
More informationElectro Pneumatic WorkStation Scientech 2470
Electro Pneumatic WorkStation is designed to demonstrate the design, construction and application of Pneumatic components and circuits. It integrates PLC technology to build Hybrid Industrial Automation
More informationRittal CM Compact System Enclosures
Rittal CM Compact System Enclosures Compact class = Top class: Infinite possibilities R Compact enclosure on the outside, Top enclosure on the inside! Index Convincing details... 3 5 Compact system enclosures
More informationOFFICE FITTINGS Monitor Arms P TV Brackets P Cable Organizers P CPU Holders P.
OFFICE FITTINGS -1 Monitor Arms P. 310-313 -2 CPU Holders P. 314-3 Keyboard Trays P. 315-317 -4 Cable Organizers P. 318-325 -5 Media Storage P. 326-334 -6 TV Brackets P. 335-336 -7 TV Lifts P. 337-339
More informationHYDROTRAINER-200 Hydraulics - Electro-hydraulics
HYDROTRAINER-200 Hydraulics - Electro-hydraulics Hydraulics and electro-hydraulics within your reach Why HYDROTRAINER-200? All components included are industrial which guarantees real learning and future
More informationTHE SPECIALIST WHERE LOTS OF SPACE IS NEEDED
80 endo-cart 81 THE SPECIALIST WHERE LOTS OF SPACE IS NEEDED endo-cart was designed especially to meet the special challenges in operating theatres. This is where every second counts and each movement
More informationHydraulics and Pneumatics Simulation Software (LVSIM -HYD & PNEU) - 1 User
6387-00 Hydraulics and Pneumatics Simulation Software (LVSIM -HYD & PNEU) - User LabVolt Series Datasheet Festo Didactic en 02/208 Table of Contents General Description 2 Topic Coverage 2 Features & Benefits
More informationDidactic and technological innovation at the service of training in pneumatics and electro-pneumatics have resulted in the creation of the
Didactic and technological innovation at the service of training in pneumatics and electro-pneumatics have resulted in the creation of the PNEUTRAINER-200 system. A fully modular system designed for the
More informationHYDROTRAINER-200 Hydraulics - Electro-hydraulics
HYDROTRAINER-200 Hydraulics - Electro-hydraulics Hydraulics and electro-hydraulics within your reach www.smctraining.com training@smctraining.com 80 Develop the SKILLS... Analysis Troubleshooting Implements
More informationPNEUMATE-200 Your mate in Pneumatics!
PNEUMATE-200 Your mate in Pneumatics! The compact trainer to help users discover more about pneumatic and electro-pneumatic technologies. www.smctraining.com training@smctraining.com 40 Develop the SKILLS...
More informationuni-cart THE RIGHT CHOICE WHERE SPACE IS AT A PREMIUM uni-cart
THE RIGHT CHOICE WHERE SPACE IS AT A PREMIUM is a compact and safe equipment cart with a loading capacity of up to 65 kg / 143 lbs. With its 4 or 5-foot-base frames and lockable wheels this trolley is
More informationD10 Page. Contents. Complete Equipment with Scope of Supplies 2. Accessories 3
01.2009 UK D10 1 D10 Page Contents Complete Equipment with Scope of Supplies 2 Accessories 3 Spare Parts D10-III 230V / 400V 4-5 Motors D10 universal 6 Transport shaft, mixing shaft 7 Electric Control
More informationHYDROMODEL-200. Implements and controls hydraulic and electro-hydraulic circuits. Transparent Hydraulics - Electro-hydraulics
HYDROMODEL-200 Transparent Hydraulics - Electro-hydraulics Hydraulic and electro-hydraulic technology at a glance Implements and controls hydraulic and electro-hydraulic circuits www.smctraining.com training@smctraining.com
More informationAutomatic Control System PS Pneumatic Training System. Features
Pneumatic Training System It is well known that Factory utomation is an indispensable measure to reduce labor cost, improve production efficiency and achieve higher product quality, which is widely adopted
More informationHydraulics Simulation Software (LVSIM -HYD) - 10 Users Network (6385-Q0)
Hydraulics Simulation Software (LVSIM -HYD) - 10 Users Network 588018 (6385-Q0) LabVolt Datasheet Festo Didactic en 12/2018 Table of Contents General Description 2 Features 2 Hydraulics Equipment 3 Computer
More informationC 200 Modern Construction. Flexible Modular Design. Highest Safety.
Ball Valve Modern Construction. Flexible Modular Design. Highest Safety. The System At A Glance Ergonomic hand lever Position locking Safety Guard Double shaft seal with hand lever Intelligent interface
More informationDS4NA Fluid Power Training System
Drive & Control Academy DS4NA Fluid Power Training System 2 Bosch Rexroth DS4NA Fluid Power Training System The data specified herein only serves to describe the product. No statements concerning a certain
More informationMobile recleanable HEPA filter units for a flow of m 3 / h
Mobile recleanable HEPA filter units for a flow of 3.000 m 3 / h Page 1/11 consisting of Mobile online recleanable HEPA filter block, Type M-RHF hightec 1 x 2 and Mobile air conveyor block, Page 2/11 RHF
More informationAirLINE and AirLINE Quick electrical/pneumatic Automation System
AirLINE and AirLINE Quick electrical/pneumatic Automation System Type 8644 can be combined with Fully compatible with Rockwell Combination of Fieldbus, pilot valves and I/O modules higher fl exibility
More informationInput, Control and Processing elements
PNEUMATIC & HYDRAULIC SYSTEMS CHAPTER FIVE Input, Control and Processing elements Dr. Ibrahim Naimi Valves The function of valves is to control the fluid path or the pressure or the flow rate. Depending
More information6080 Hydraulics Training System
6080 Hydraulics Training System LabVolt Series Datasheet Festo Didactic en 240 V - 50 Hz 03/2018 Table of Contents General Description 2 Innovative Design 3 Virtual Laboratory Equipment 3 Courseware 3
More information[You may download this article at: https://fluidsys.org/downloads/ ]
Fluidsys Training Centre, Bangalore offers an extensive range of skill-based and industry-relevant courses in the field of Pneumatics and Hydraulics. For more details, please visit the website: https://fluidsys.org
More informationIntroduction. Pre-Lab
The University Of Jordan School of Engineering Mechatronics Engineering Department Fluid Power Engineering Lab Experiments No.2 Pneumatic Control of a Double-acting Cylinder Objective: Students will be
More informationOperating Instruction Manual for Energy Management System EBL 99 C, Art.-Nr Seite 1 / 7
EBL 99 C, Art.-Nr. 911.413 Seite 1 / 7 Contents 1. Description 2. Safety Information 3. Operating Instructions 4. Transport, Storage, Installation 5. Electrical Installation 6. Power-Up, Shut-Down, Maintenance
More informationKnürr Smaract. Knürr Smaract. CompactRack
CompactRack Features Ample space for components and cabling provided in an efficient, compact design. The innovative frame concept with triangular extrusions ensures low weight while maintaining high stability.
More information2006/42/EG, DIN EN ISO 12100, DIN EN
181 brühl machine guard doors and gates BRÜHL Machine guard doors and gates In accordance with the Machinery Directive 2006/42/EG, DIN EN ISO 12100, DIN EN 12453 and DIN EN 12604 182 Machine guard lift
More informationSpare parts Catalogue number
1A Air pump 601011372-000 Air pump 230V/50Hz 1B Air pump 601011510-000 Air pump 230V/50Hz 1C Air pump 601011220-000 Air pump 230V/50Hz 1D Air pump 601011511-000 Аir pump 1V 230V/50Hz 1E Air pump 601011225-000
More informationGIMA LIGONIŲ PERVEŽIMUI VEŽIMĖLIAI IR JŲ PRIEDAI
GIMA LIGONIŲ PERVEŽIMUI VEŽIMĖLIAI IR JŲ PRIEDAI Eil. Nr. 1. Aprašymas 1.1 27800 PATIENT TROLLEY Made of chrome plated steel tube, and washable self extinguishing plastic material. Comes complete with
More informationMONO - MOTRONIC 0309 En
02.1992 MONO - MOTRONIC 0309 En Published by: Robert Bosch GmbH Division KH After-Sales-Service Department for Training and Technology (KH/VSK) Please direct questions and comments concerning the contents
More informationUniversal Fluid Power Trainer (UFPT)
Universal Fluid Power Trainer (UFPT) Milwaukee School of Engineering Applied Technology Center TM Department of Professional Education The UFPT is a modular, smart and unique fluid power and motion control
More informationClimate chambers with illumination
KBW series (E5.1) Climate chambers with illumination Climate chambers with illumination The BINDER KBW series climate chamber with illumination achieves homogeneous light distribution and ensures consistent
More informationProduct Catalog Evacuated tube collectors CPC OEM CPC w OEM
Product Catalog 2004 Evacuated tube collectors CPC OEM CPC w OEM Table of Contents Development/design Production Outgoing goods warehouse Table of Contents Page Evacuated tube collectors CPC 6 OEM, CPC
More informationProduct Data For FARNELL
ae Product Data For FARNELL ae Uniset is / Varioset is ae EL ELECTRONIC KOMBI SYSTEM WALL MOUNTING Pole clamp For reliable, convenient fastening to round or square poles. For pole diameter/size:
More informationPneumatic and Electro-Pneumatic Application AE-NS INTRODUCTION
Pneumatic and Electro-Pneumatic Application Engineering and Technical Teaching Equipment AE-NS AE-NS. Pneumatic and Electro-Pneumatic Application INTRODUCTION Pneumatics is the technology that employs
More informationMechatronics systems
Mechatronics systems www.matrixtsl.com 1 HP4550 Solution Description This solution contains products from our Locktronics, E-blocks and Automatics ranges. The pack includes a wide variety of resources
More informationApplications Profitronic 19 / Profitronic 19U
Applications Profitronic 19 / Profitronic 19U 54 Enclosure in variable length version using profile technology Standard construction or version with connection compartment Optional Polycarbonate transparent
More information: Automation Laboratory 1
Table A.1 shows elements found in FluidSIM library with a brief description for each of them. Compressed air supply The compressed air supply provides the needed compressed air. It contains a pressure
More informationIntegrated temperature test and calibration bench Model CBS-SC4000
Calibration technology Integrated temperature test and calibration bench Model CBS-SC4000 WIKA data sheet CT 92.33 Applications Testing and calibration of temperature measuring instruments such as: - Mercury
More informationCrimping and cutting tools FHP 2 PHD 1. Hydraulic drive units. Foot pump 700 bar
FHP 2 Foot pump 700 bar Two stage hydraulics Manual retraction in case of need, even at high pressure Sturdy design Automatic pressure switch off High-pressure hose, 2 m 12.0 kg Foot pump 700 bar FHP2
More informationClimate chamber with illumination
KBW series (E5.1) Climate chambers with illumination Climate chamber with illumination The BINDER climate chamber with illumination of the KBW series achieves homogeneous light distribution with its natural
More informationA Fluid Power PNEUMATICS TRAINING SYSTEMS SERIES 6081
A Fluid Power PNEUMATICS TRAINING SYSTEMS GENERAL DESCRIPTION The Lab-Volt Pneumatics Training System, Model 6081, is a modular program in pneumatics and its applications. The system is divided into five
More informationControls F792 Switchbox LP Series
Controls F792 Switchbox LP Series The well proven design of the Keystone F792 Low Profile Switchbox has been upgraded to simplify setting, site wiring and weatherproof integrity. Features Cams specially
More informationStirrup-shaped handles, machine handles, apparatus handles
Stirrup-shaped handles, machine handles, apparatus handles 231 K0186 Stirrup-shaped handles GJS 400 Deburred and tumble cleaned; black plastic coated; machined contact faces. KIPP Stirrup-shaped handles
More informationHAFNER Pneudactic Pneumatic Training Sets
HAFNER Pneudactic Pneumatic Training Sets Page 2 HAFNER pneudactic The HAFNER pneudactic training sets have been developed to educate students or employees in the basics of the use of pneumatic components
More information19!Cabinets! Knürr!Dacobas. h = Installation height (ideal for 19" components d = Useful depth in acc. with DIN 41494)
Knürr!Dacobas 19!Cabinets! Technical systems are not installed in large numbers directly in the workstation system for the most diverse reasons, but rather alongside or in a special central technical room.
More informationMachine protection doors. MS series
Machine protection doors MS series EFA-SRT MS A glance at the advantages of the EFA-SRT MS high speed roll-up door: EC type-tested safety component according to Machinery Directive 2006 / 42 / EG Suitable
More informationSpare Parts List GS 14 / GS 15 GS 14 E / GS 15 E
win ter h lter Spare Parts List GS 14 / GS 15 GS 14 E / GS 15 E Edited: 03/97 Revised: 12/00 Part no.: 89002487 Summary Water supply Pages 1 and 2 SoftMatik (Softener) Pages 3 and 4 Tank heating and water
More informationElectrohydraulics Basic Level Textbook TP 601
Electrohydraulics Basic Level Textbook TP 601 Festo Didactic 093611 en Order No.: 093611 Edition: 03/2006 Authors: C. Löffler, D. Merkle, G. Prede, K. Rupp, D. Scholz Graphics: Doris Schwarzenberger Layout:
More informationUrea Technology.
Urea Technology Urea Electrical Diaphragm Pumps Diaphragm pumps with integrated bypass, on-off switch Our electric diaphragm pumps stand for first-class electrical machinery and pump construction. They
More informationHydraulic clamping elements
Hydraulic clamping elements hydraulic 3 Contents Product group 3 Hollow piston cylinder single-acting 3.1403 3.2130 Sliding clamp single-acting compact classic 3.2202 3.2204 Angular clamping element single
More informationmono-mix Contents Complete Equipment with Scope of Supplies 3 Accessories 4-5 Spare Parts
mono-mix Contents Page Complete Equipment with Scope of Supplies 3 Accessories 4-5 Spare Parts mono-mix-fu 230V 1ph 6-9 Control panel FU 230V 1ph 10-13 Control panel FU 230V 1ph with water delay relay
More informationMobile service module for on site employment in mining. for supply of large machinery with fuels, oils and lubricating grease
Mobile service module for on site employment in mining for supply of large machinery with fuels, oils and lubricating grease The on-site supply concept Krampitz - solution: mobile service module 2 We have
More informationELECTRO HYDRAULIC THRUSTERS
ELECTRO HYDRAULIC THRUSTERS THE ORIGINAL. BE SAFE..moving ahead. DESIGN, FUNCTION AND ADVANTAGES LIFTING ROD HEAD OIL FILLING SEALING SYSTEM LIFTING ROD REGULATION PLUG VALVES BRAKE SPRING (C SPRING) 1)
More informationActual-position Feedback Unit. SISTO-SK-i. For Valves with Linear Actuators Stroke: 5-46 mm. Type Series Booklet
SISTO-SK-i For Valves with Linear Actuators Stroke: 5-46 mm Type Series Booklet Legal information/copyright Type Series Booklet SISTO-SK-i All rights reserved. The contents provided herein must neither
More informationKnürr CiCon Modular consoles for every room concept plan-friendly, economical und ergonomic. Technical Furniture
Knürr CiCon Modular consoles for every room concept plan-friendly, economical und ergonomic Technical Furniture Knürr CiCon The Circular Console With momentum into a new, modern, current requirements-oriented
More informationPneumatic Power Valves Series 75/76 Manual, Mechanical, Pneumatic and Electric Valves
Quic-Pics Catalogue Pneumatic Power Valves Series 75/76 Manual, Mechanical, Pneumatic and Electric Valves Contents: Product Line Overviews 2 Manually Operated Valves 5 Pushbuttons 6 Toggle Switch 8 Knob
More informationHumidity Cabinet HYGROTHERM
Humidity Cabinet for humidty tests with international standards Humidity Cabinet HYGROTHERM 519 529 HYGROTHERM also available as semi-automatic or fully-automatic version (Mod. 519 SA / 519 FA) HYGROTHERM
More informationGTK 80. Technical data
Industrial square suspension system with open cable duct for heavy loads Modular construction with free accessible cable duct Floor, top-mounting or wall exit options Technical data Material: connecting
More informationUniversal Fluid Power Trainer (UFPT)
Universal Fluid Power Trainer (UFPT) The UFPT is a modular, smart and unique fluid power and motion control training unit. It contains an excellent integration of industrial-graded hardware and builtin
More informationCompressed Air Conditioning. accessories. One Stop Shop process reliable efficient economical high degree of reusability
Screwdriving technology Automation Air motors Air tools Compressed Air Conditioning and Accessories One Stop Shop process reliable efficient economical high degree of reusability DEPRAG offers a comprehensive
More informationSECTION B: SYSTEM OPERATING COMPONENTS
SECTION B: SYSTEM OPERATING COMPONENTS A brief description of the machine, Cable Processor Module and tooling will provide a better understanding of the various functions of the IMA system. SECTION B1:
More informationBIOSTAT D+ 100 MICROBIAL FERMENTER SYSTEM
BIOSTAT D+ 100 MICROBIAL FERMENTER SYSTEM Sartorius BBI Systems GmbH P. O. Box 13 63 D - 34203 Melsungen Tel.: 0049-5661-71 38 42 Fax: 0049-5661-92 99 49 www.sartorius-bbi-systems.de info@sartorius-bbi-systems.com
More informationACCESSORIES FOR SZE2 CABINETS
ZPAS 143 DOORS Doors Intended for use instead of front solid door or rear panel. Maximum door opening angle: 120 Sheet steel textured powder paint, light grey (RAL 7035), stiffened profiles, brown smoked
More informationProfitronic I. Technical data
Profitronic I Aluminium electronic enclosure for telecommunication and MCR technology Variable length version using profile technology Screw-down fins integrated into sides Different lid versions depending
More informationRemote Process Actuation Control System AirLINE - Rockwell 1734 Point I/O System
Remote Process Actuation Control System AirLINE - Rockwell 1734 Type 8644 can be combined with... Fully compatible with Rockwell 1734 Point I/O System Combination of Fieldbus, pilot valves and I/O modules
More informationALUMINIUM PROFILE SYSTEM SERIES 40
ALUMINIUM PROFILE SYSTEM SERIES With the basic grid mm (slot 5); mm (slot 6), 16mm, mm and 0mm (slot ). In addition to this, the complete connection technology and a large range of accessories. TABLE OF
More informationMobile Column Lift EHB 707 Standard
Mobile Column Lift EHB 707 Standard Mobile and universal use, indoors and outdoors. Practical and easy maneuverability of every column, short set-up time and fast lifting speed. Maximum safety utilizing
More informationRoller brake tester for Cars, Vans and Light Trucks
Wir im Allgäu. Roller brake tester for Cars, Vans and Light Trucks The MAHA modular system the individual tester from the series including brake testers up to testing lanes Testing & Safety Technology
More informationpartial statement 106 TITUS www.efb-elektronik.de 19 Networking cabinet TITUS S (Standard)... 108-109 19 Networking cabinet TITUS E (Enhanced)...110-111 19 Networking cabinet TITUS V (pre-assembled)...
More informationHydraulic pump HP-1. Type 1. Type 2
The BEKA-MAX central lubrication pump model HP-1 is hydraulic actuated and has up to a maximum of independently operating lubricant outlets. A separate pump unit is required for each outlet. Three pump
More information1 01 / 201 Edition ED. 01/2007
Edition 01 / 2011 ED. 01/2007 TABLE OF CONTENENTS 1 INTRODUCTION 2 GRIPPER EXAMPLES 2.1 EXAMPLE A: GRIPPER WITH TUBES AND ALUMINIUM PROFILES 2.2 EXAMPLE B: GRIPPER WITH STAINLESS STEEL TUBES 2.3 EXAMPLE
More informationAutomatic filter AF 112 G
Automatic filter AF 112 G Cast design with internal pressure cleaning and integrated cyclone effect Connection size: flange DN 40 or G1 1/2 1 Short description MAHLE automatic backflush filters are suitable
More informationSECTION B1: MACHINE COMPONENTS
SECTION B1: MACHINE COMPONENTS The machine portion of the Injected Metal Assembly system provides the means for: holding, heating and injecting the alloy; distributing and controlling electrical, pneumatic,
More information«Standard» Hydraulic power unit BM
«Standard» Hydraulic power unit BM Tank volume V max = 25 l Flow rate Q max = 25,5 l/min Motor power P max = 3 kw CONTENT CHARACTERISTICS...1 DESCRIPTION...1 FUNCTION...1 ENERGY EFFICIENCY...1 KEY DATA
More informationSicher und flexibel die neue Antriebsgeneration actubar
A Module of the Valve-Control System bar-vacotrol -positurn2 Sicher und flexibel die neue Antriebsgeneration actubar Positioner and 3-position control unit for part-turn actuators Objective Function bar-positurn2
More informationDrive & Control Academy DS4NA Fluid Power Training System
Drive & Control Academy DS4NA Fluid Power Training System New: simplified model coding and ordering 2 03 Drive & Control Academy 05 DS4NA Fluid Power Training System 05 System description 06 Technology
More informationProduct facts Geryon SRD Security Revolving Doors STS Security Turnstiles
Product facts Geryon SRD Security Revolving Doors STS Security Turnstiles Automatic access control to prevent unauthorised access to restricted areas. Security Revolving Doors SRD Basic equipment SRD-E01
More informationINDEX. Chapter2. air master. Grilles and Registers
Chapter2 INDEX A.Grilles and registers. 1. Supply air grille - front horizontal blades...: ASG-H...2.1 2. Supply air grille - front vertical blades...: ASG-V...2.2 3. Supply air register - front horizontal
More information