Suggested list for the Hydraulic and Pneumatic lab Instruments Mechatronics Engineering Department School of Applied Technical Science
|
|
- Philippa Young
- 6 years ago
- Views:
Transcription
1 Suggested list for the Hydraulic and Pneumatic lab Instruments Mechatronics Engineering Department School of Applied Technical Science Pneumatic and Electro-pneumatic components: No. EQUIPMENTS operating Pressure (bar) QTY PNEUMATIC WORKBENCH Self-contained workplace. Mobile workstation, mounting frame at least 00 x 700 mm. A cabinet frame for the electrical components. Working Table compatible for both Lab workstation and electromodule frame. 2 3 Wheeled drawer unit (contains at least 3 drawers). AIR SERVICE UNIT: adjustable pressure:0-0 bar Filter-Regulator-Lubricator assembly pressure gauge PRESSURE gauge: AIR MANIFOLD: 6 PORTS SINGLE ACTING CYLINDER: internal diameter >= 25 mm stroke >=50 mm DOUBLE ACTING CYLINDER: Air CUSHIONING 7 9 internal diameter >= 25 mm stroke >=50 mm 3/2 WAY DIRECTIONAL CONTROL VALVE: single air operated,spring return 5/2 WAY DIRECTIONAL CONTROL VALVE: single air operated,spring return 5/2-WAY DIRECTIONAL CONTROL VALVE: 20
2 0 double air pilot,and return 5/2-WAY SINGLE-SOLENOID VALVE: solenoid voltage :2 VDC single solenoid operated spring return with LED 5/2-WAY DOUBLE-SOLENOID VALVE: solenoid voltage 2 VDC pilot operated with LED 3/2-WAY MANUAL VALVE: manually operated with push button, spring return 3/2-WAY MANUAL VALVE: 2-position selector, with spring return 3/2-WAY MANUAL VALVE: push and lock, with spring return 5/2-WAY Manually OPERATED WITH PB VALVE: manually operated with push button, spring return 3/2-WAY ROLLER VALVE: Uni-Directional 3/2-WAY ROLLER VALVE : Bi-Directional 3/2-WAY DIRECTIONAL CONTROL VALVE : Single pilot, Flow in both direction Operating pressure : bar 5/3- WAY DIRECTIONAL CONTROL VALVE: Pneumatically operated (Double pilot),mid-position closed Operating pressure : bar 5/3- WAY DIRECTIONAL CONTROL VALVE Double Solenoid,Mid-Position Closed 2 Operating pressure : bar SHUTTLE VALVE: OR Logic
3 22 23 TWIN PRESSURE VALVE: AND Logic QUICK EXHAUST VALVE: ONE-WAY FLOW CONTROL VALVE: non return one way valve, with speed controller SEQUENCE VALVE: operating pressure : bar TIME DELAY VALVE: Time delay : sec PRESSURE SWITCH 20 2 AIR HOSE : 200 m 29 compatible with the components DC POWER SUPPLY MODULE: input voltage: 220/230 VAC,50/60 Hz output voltage: 2 VDC 2 terminals for power output 30 consists of short-circuit protection PUSHBUTTON SWITCH MODULE: spring return,at least 2 sets of Normally opened(no),and sets of Normally closed(nc) contacts 3 operating voltage : 2 VDC 2 RELAY MODULE: changeover contacts, with LED indicator operating voltage : 2 VDC TIMING RELAY MODULE: Switch -on Delay operating voltage : 2 VDC 32 Time Delay: sec 2 sets of NO,NC contacts with LED display
4 TIMING RELAY MODULE: Switch -off Delay operating voltage : 2 VDC Time Delay: sec 2 sets of NO,NC contacts with LED display CONNECTING LEAD: Lead diameter: mm 3 different lengths 3 different colors 60 pcs in a set two sided banana plugs,suitable with other electrical components ELECTRICAL LIMIT SWITCH (RIGHT): Roller lever type NO,NC contacts ELECTRICAL LIMIT SWITCH (LEFT): Roller lever type NO,NC contacts 3-WAY DISTRIBUTER (T-connection): Compatible with the tubes used between components AIR SUPPLY UNIT: Quit Compressor,noise less,ideal for use in class rooms Pressure max. : -0 bar Free air delivery : 50 L/min Tank capacity :at least 25 L Electric motor : V/50 Hz, Watt Accessories: quick coupling socket and plug, tubing for the compressor TUBE CUTTER FOR PLASTIC TUBES DISPLAY UNIT, LED DISPLAYS: sets 32 Shows voltage/current come from Electric Module
5 COUNTER Module operating voltage : 2 VDC MAGNETIC PROXIMITY SWITCHES: input voltage: 2 VDC it is intended to sense position of the rod. PHOTOELECTRIC SWITCHES: input voltage: 2 VDC it is intended to sense position of the rod. Pressure sensor with indicator: input voltage: 2 VDC it is intended to sense position of the rod. Proximity switch, inductive: input voltage: 2 VDC Proximity switch, capacitive: input voltage: 2 VDC 7 Counter for electro-pneumatic 9 Trainer's Manual provides detailed examples and exercises for the pneumatics and electro pneumatics circuits Trainee's Manual provides detailed examples and exercises for the pneumatics and electro pneumatics circuits 2 50 Input /Output interface 5 Pneumatic Bi-directional Motor 52 2 Reflex nozzle/ suction nozzle 53 3/2 DCV G/ amplifier 2-stage 5 Vacuum pump Rotary pump with a capacity of 50L/m or greater, 50/60Hz 55 Triple Power Supply 2 x 0 32 V/0 2 A x V/0 5 Display Resolution: 0 mv/ ma at Channel +3; 0 mv/0 ma at Channel 2
6 Hydraulic and Electro-hydraulic components: No. Equipment QTY HYDRAULIC WORKBENCH: Self-contained workplace Mobile workstation includes profile plating and mounting frame at least 500 x 600 mm. A cabinet frame for the electrical components. Working Table suitable for both Lab workstation and electromodule frame. Holder for up to 20 hydraulic hoses and cables Oil spillage /protective mate 300x500 mm HYDRAULIC POWER UNIT: tank capacity: min 5 L P max: 60 bar Electric motor: HP phase,220/230vac,50/60 Hz Suitable hydraulic oil PRESSURE GUAGE: operating pressure:0-50 bar ACCUMULATOR: operating pressure:0-00 bar INLINE FLOW METER: operating pressure:0-25 bar DOUBLE ACTING CYLINDER: diameter: min 0 mm stroke length:min 200 mm operating pressure:0-0 bar DIFFERENTIAL HYDRAULIC CYLINDER: diameter:min 0 mm stroke length: min 200 mm operating pressure:0-0 bar surface area ratio:2: 6 6
7 DOUBLE ACTING CYLINDER: diameter: min 0 mm stroke length: min 200 mm operating pressure:0-25 bar cylinder s body attached with 2 reed switches LOADING WEIGHT: Consists a spring enclosed in a clear tube. Must be mounted to the cylinder to measure cylinder force output at different piston pressure HYDRAULIC MOTOR: Min. rotary speed:0 rpm Max. flow rate:20l/min 2/2-WAY SINGLE-SOLENOID VALVE: spring return solenoid operating voltage:2 VDC 3/2-WAY SINGLE SOLENOID VALVE: spring return solenoid operating voltage:2 VDC /2-WAY SINGLE SOLENOID VALVE: Spring return Solenoid operating voltage:2 VDC /3-WAY DOUBLE SOLENOID VALVE: Closed center Solenoid operating voltage:2 VDC /3-WAY DOUBLE SOLENOID VALVE: Center PT type Solenoid operating voltage:2 VDC 6
8 /2-WAY DCV: NC Type Hand Lever operated with spring return /2-WAY DCV: Hand Lever operated with spring return /3-WAY DCV: Closed center, spring return /3-WAY DCV: Center ABT type, spring return CHECK VALVE: One way control Operating pressure:5-20 bar PILOT-OPERATED CHECK VALVE: Operating pressure: bar FLOW CONTROL VALVE: Non-return valve with speed controller Operating pressure:5-20 bar 2-WAY THROTTLE VALVE: 2-way flow control PRESSURE COMPENSATED FLOW CONTROL VALVE: Operating pressure:5-20 bar PRESSURE RELIEF VALVE: Direct operated, ball/screw adjusting 6
9 PILOT-OPERATED PRESSURE RELIEF VALVE: Ball/Screw adjusting 3-WAY PRESSURE REDUCING VALVE: SEQUENCE VALVE: Ball/Screw adjusting COUNTERBALBNCE VALVE: PRESSURE DISTRIBUTOR: Different couplings with pressure gauge RETURN DISTRIBUTOR 3-WAY DISTRIBUTOR -WAY DISTRIBUTOR SHUT-OFF VALVE: Manually operated HOSE,0.5m HOSE,m HOSE,.5m PRESSURE SWITCH: Operating pressure:5-00 bar NO,NC,COM contacts DC POWER SUPPLY: Output voltage: 2 VDC 2 terminals for power output Consists of short circuit protection PUSHBUTTON SWITCH MODULE: At least 2 NO,and NC contacts Operating voltage : 2 VDC
10 SELECTOR SWITCH MODULE: Selector switch with NO,NC contacts Operating voltage : 2 VDC RELAY MODULE: changeover contacts, with LED indicator Operating voltage : 2 VDC TIMING DELAY MODULE: SWITCH -on DELAY Operating voltage : 2 VDC Time Delay: sec 2 sets of NO,NC contacts with LED display COUNTER Module Operating voltage : 2 VDC operating voltage : 2 VDC Lead diameter: mm 3 different lengths 3 different colors 60 pcs in a set Two sided banana plugs LIMIT SWITCH (LEFT): Roller lever type NO,NC contacts LIMIT SWITCH (RIGHT): Roller lever type NO,NC contacts REED SWITCH: Operating voltage : 2 VDC PILOT LAMP STATION Trainer's Manual provides detailed examples and exercises for the hydraulics and electro hydraulics circuits Trainee's Manual provides detailed examples and exercises for the hydraulics and electro hydraulics circuits 6
11 53 Electrical power supply with connection cable 2 5 Electrical manifold 55 Input /Output interface /2-WAY DCV Hydraulic actuated and spring return 57 /2-WAY DCV Hydraulic actuated and spring return 5 5/2-WAY DCV Hydraulic actuated and return 59 /3-WAY DCV Hydraulic actuated and return 60 /3-WAY DCV Hydraulic actuated and spring return, closed center 6 Diffuse reflective photoelectric switch 63 Automation studio software
12 PLC Unit No. EQUIPMENT QTY PLC Unit 6 Digital inpu (DI)/ 6 Digital Output/ analog input/ 2 Analog output/ SIM, with place holder module complete 2 VDC power supply MPI Adaptor for the PLC USB port Wires for the PLC unit 2 Universal connection unit, Digital 3 Universal connection unit, Analog Manual for PLC Unit documentation on CD-Rom/ a book covers the structure and mode of operation of the PLC 5 PLC Software suitable for PLC interface
SAP E & C ADVANCED CUSTOMIZED ELECTRO PNEUMATIC TRAINER (FOR ITI) (PRODUCT CODE: SAP 20B-I)
The Advanced Customized Electro Pneumatic Trainer (SAP 20B-I) is capable of being used to demonstrate the design, construction and application of electro-pneumatic components and circuits. Objectives:-
More informationAutomatic Control System PS Pneumatic Training System. Features
Pneumatic Training System It is well known that Factory utomation is an indispensable measure to reduce labor cost, improve production efficiency and achieve higher product quality, which is widely adopted
More informationADVANCED CUSTOMIZED ELECTRO PNEUMATIC TRAINER (PRODUCT CODE: SAP 20B)
The Advanced Customized Electro Pneumatic Trainer (SAP 20B) is capable of being used to demonstrate the design, construction and application of electro-pneumatic components and circuits. Objectives:- The
More informationElectro Pneumatic WorkStation Scientech 2470
Electro Pneumatic WorkStation is designed to demonstrate the design, construction and application of Pneumatic components and circuits. It integrates PLC technology to build Hybrid Industrial Automation
More informationDidactic and technological innovation at the service of training in pneumatics and electro-pneumatics have resulted in the creation of the
Didactic and technological innovation at the service of training in pneumatics and electro-pneumatics have resulted in the creation of the PNEUTRAINER-200 system. A fully modular system designed for the
More informationPneumatics Electropneumatics
Training systems for basic and future oriented education in natural science and engineering Pneumatics Electropneumatics Experimental Panel and Module System 07 / 2003 Contents Experimental panel system..........................
More informationPNEUTRAINER-200 Pneumatics - Electro-pneumatics
PNEUTRAINER-200 Pneumatics - Electro-pneumatics End-to-end solution for training in pneumatics and electro-pneumatics. www.smctraining.com training@smctraining.com 46 Develop the SKILLS... Analysis Troubleshooting
More informationPNEUTRAINER-400 Pneumatics - Electropneumatics
PNEUTRAINER-400 Pneumatics - Electropneumatics End-to-end solution for training in pneumatics and electro-pneumatics SMC industrial systems components on panel mounting plate Implements and controls pneumatic
More informationElectro Pneumatic Workbench Scientech 2470
Scientech 2470 Electro Pneumatic Workbench is designed to demonstrate the design, construction and application of Pneumatic components and circuits. It integrates PLC technology to build Hybrid Industrial
More information: Automation Laboratory 1
Table A.1 shows elements found in FluidSIM library with a brief description for each of them. Compressed air supply The compressed air supply provides the needed compressed air. It contains a pressure
More informationSubject: Pneumatic Training Kit with portable Air Compressor
MSME TOOL ROOM: HYDERABAD (CENTRAL INSTITUTE OF TOOL DESIGN) Balanagar, Hyderabad 500 037 TEL.NO.23772747, 23776168 FAX No.0-4023772658 E-mail:citdpurchase@citdindia.org Visit us: www.citdindia.org. TENDER
More informationTraining Systems for Pneumatics R /
Training Systems for Pneumatics R999000218 /11.2015 2 Training Systems for Pneumatics Training Systems for Pneumatics Drive & Control Academy 4 Training systems pneumatics 8 Device sets 10 Study topics
More informationIntroduction. Pre-Lab
The University Of Jordan School of Engineering Mechatronics Engineering Department Fluid Power Engineering Lab Experiments No.2 Pneumatic Control of a Double-acting Cylinder Objective: Students will be
More informationA Fluid Power PNEUMATICS TRAINING SYSTEMS SERIES 6081
A Fluid Power PNEUMATICS TRAINING SYSTEMS GENERAL DESCRIPTION The Lab-Volt Pneumatics Training System, Model 6081, is a modular program in pneumatics and its applications. The system is divided into five
More informationHYDROTRAINER-200 Hydraulics - Electro-hydraulics
HYDROTRAINER-200 Hydraulics - Electro-hydraulics Hydraulics and electro-hydraulics within your reach Why HYDROTRAINER-200? All components included are industrial which guarantees real learning and future
More informationPart8 Pneumatics / Hydraulics
Part8 Pneumatics / Hydraulics PART8. Pneumatics / Hydraulics ED-7860_PNEUMATICS TRAINER» PT-7861_COMMON EQUIPMENT & COMPONENT REQUIREMENTS» PT-7862-1_COMPONENTS OF PNEUMATIC CONTROL(ESSENTIAL COMPONENTS)»
More informationCURRICULUM BOSCH-REXROTH (CENTRE OF EXCELLENCE) GANPAT UNIVERSITY
ANNEXURE - A CURRICULUM BOSCH-REXROTH (CENTRE OF EXCELLENCE) Host Institute: GANPAT UNIVERSITY Contents of Basic Industrial Pneumatics -----------------------------------------------------------------------------------------------------------------
More informationDISCUSSION OF FUNDAMENTALS. A hydraulic system can be controlled either manually or automatically:
Unit 1 Introduction to Electrical Control of Hydraulic Systems UNIT OBJECTIVE When you have completed this unit, you will be able to identify the components used for electrical control of the Hydraulics
More informationHYDROMODEL-200. Implements and controls hydraulic and electro-hydraulic circuits. Transparent Hydraulics - Electro-hydraulics
HYDROMODEL-200 Transparent Hydraulics - Electro-hydraulics Hydraulic and electro-hydraulic technology at a glance Implements and controls hydraulic and electro-hydraulic circuits www.smctraining.com training@smctraining.com
More informationZ1 B1 B2 Z2 B3 B4. Steuerteil + 24 V. Leistungsteil K1 K2 K1 K2. Practice for Professionals Electropneumatics Trainee s manual. Version 1.
04 Z1 B1 B2 04 Z2 B3 B4 31 14 Y1 12 4 2 5 3 1 15 31 14 Y2 12 4 2 5 3 1 15 Steuerteil + 24 V B1 S0 K1 B2 K2 B4 K3 B3 Leistungsteil 1 2 3 4 5 6 7 8 9 K4 K1 K2 0V K1 K2 K1 K3 K2 K4 K3 Y1 K3 Y2 Practice for
More informationED-7860_ PNEUMATICS TRAINER
Part 8 ED-7860_ TRAINER» PT-7861_ COMMON EQUIPMENT & COMPONENT REQUIREMENTS» PT-7862-1_ COMPONENTS OF (ESSENTIAL COMPONENTS)» PT-7862-2_ COMPONENTS OF (ADDITIONALLY RECOMMENDED COMPONENTS)» PT-7863-1_
More informationBASIC PNEUMATIC & ELECTROPNEUMATIC TRAINING SYSTEM
BASIC PNEUMATIC & ELECTROPNEUMATIC TRAINING SYSTEM UCTECH has designed a comprehensive range of specialised training packages and products for pneumatic and electro-pneumatic training using well-known
More informationHydraulics Simulation Software (LVSIM -HYD) - 10 Users Network (6385-Q0)
Hydraulics Simulation Software (LVSIM -HYD) - 10 Users Network 588018 (6385-Q0) LabVolt Datasheet Festo Didactic en 12/2018 Table of Contents General Description 2 Features 2 Hydraulics Equipment 3 Computer
More informationFor system diagrams and component identification
Pneumatic Symbols For system diagrams and component identification Contents Standards Actuators Basic symbols Valve symbol structure t Functional elements Flowlines Connections Conditioners and plant Pressure
More informationHYDROTRAINER-200 Hydraulics - Electro-hydraulics
HYDROTRAINER-200 Hydraulics - Electro-hydraulics Hydraulics and electro-hydraulics within your reach www.smctraining.com training@smctraining.com 80 Develop the SKILLS... Analysis Troubleshooting Implements
More informationTable of Contents. Table of Contents Pneumatik / Hydraulik
Table of Contents Table of Contents Pneumatik / Hydraulik Pneumatics with UniTrain Hydraulics with UniTrain PBC / PEC Pneumatics and Electro-Pneumatics PBC Fluid power trainer pneumatics set PBC 2 Fluid
More information6081 Pneumatics Training System
6081 Pneumatics Training System LabVolt Series Datasheet Festo Didactic en 220 V - 50 Hz 03/2018 Table of Contents General Description 2 Innovative design 3 Virtual Laboratory Equipment 3 Courseware 3
More informationElectrohydraulics Advanced Level Workbook TP 602
Electrohydraulics Advanced Level Workbook TP 602 Festo Didactic 094471 en Authorised applications and liability The Learning System for Automation and Communication has been developed and prepared exclusively
More informationMechanical Engineering
Mechanical Engineering Stepper Motor Drive Full step controlling of stepper Motor Single step, low and high speed, Forward and Reverse Small stepper Motor with driver and Power Circuit Necessary Power
More informationPNEUMATE-200 Your mate in Pneumatics!
PNEUMATE-200 Your mate in Pneumatics! The compact trainer to help users discover more about pneumatic and electro-pneumatic technologies. www.smctraining.com training@smctraining.com 40 Develop the SKILLS...
More informationAQUASTAR C6. (Comfort 6000) Next Generation Auto Backwash Valve System. (selectable time-pressure or remote cycle start)
AQUASTAR C6 (Comfort 6000) Next Generation Auto Backwash Valve System (selectable time-pressure or remote cycle start) SIDE MOUNTED AND TOP MOUNTED VALVES WITH QUICK INSTALL ELECTRIC ACTUATORS FOR PIPE
More informationPneumatic and Electro-Pneumatic Application AE-NS INTRODUCTION
Pneumatic and Electro-Pneumatic Application Engineering and Technical Teaching Equipment AE-NS AE-NS. Pneumatic and Electro-Pneumatic Application INTRODUCTION Pneumatics is the technology that employs
More informationMaintenance Instructions & Parts List
PM-PTR/LTR-C Automation Actuator Division Wadsworth, Ohio 448 October 7, 993 Rev. October 999 PTR/LTR Series Actuators Maintenance Instructions & Parts List Provide Model Number and Serial Number When
More information[You may download this article at: https://fluidsys.org/downloads/ ]
Fluidsys Training Centre, Bangalore offers an extensive range of skill-based and industry-relevant courses in the field of Pneumatics and Hydraulics. For more details, please visit the website: https://fluidsys.org
More informationInput, Control and Processing elements
PNEUMATIC & HYDRAULIC SYSTEMS CHAPTER FIVE Input, Control and Processing elements Dr. Ibrahim Naimi Valves The function of valves is to control the fluid path or the pressure or the flow rate. Depending
More informationThe pneumatic circuit and parts' list needed to perform this operation are shown by Figure C.1.
Introduction In session 1 you have learned about pneumatic systems and their main components. In addition to that your lab instructor has introduced to you how to use FluidSIM software. During this appendix
More informationActuators and directional control valves
Actuators and directional control valves 1. Differentiate between the main types of directional control valves. 2. Demonstrate the function and uses of 3/2 way valve, push button actuated. 3. Demonstrate
More informationLearning System for Automation and Communications. Electropneumatics. Workbook Basic Level S1 K1 K1 Y1
Learning System for Automation and Communications Electropneumatics Workbook Basic Level 1 2 3 S1 K1 K1 S2 K1 094005 Order no. 094005 Description: TEACHW.E-PNEUM. Designation: D.S201-C-GB Edition: 08/1993
More informationPush buttons are of two types i) Momentary push button ii) Maintained contact or detent push button
ELECTRO-PNEUMATIC Push button switches A push button is a switch used to close or open an electric control circuit. They are primarily used for starting and stopping of operation of machinery. This causes
More informationDrive & Control Academy Fluid Power Training Systems. Training topics for industrial and mobile hydraulics
Drive & Control Academy Fluid Power Training Systems Training topics for industrial and mobile hydraulics 2 03 Drive & Control Academy 05 Training Systems 05 Fluid Power Training Systems DS2NA, DS4NA 06
More informationIndustrial Pneumatic Systems Syllabus [Detailed]
TECHNICAL TRAINING - SWAPPING DOWNTIME FOR PRODUCTIVITY! Industrial Pneumatic Systems Syllabus [Detailed] 1. Fundamentals of Fluid Power Systems. The three states of matter. Definition of a fluid. Derivation
More informationMF100BH (BASIC HYDRAULICS TRAINER) PARTS LIST CATALOG APRIL 2013
MF100BH (BASIC HYDRAULICS TRAINER) PARTS LIST CATALOG APRIL 2013 MF100BH (BASIC HYDRAULICS TRAINER) PARTS LIST NOTE: Asterisk (*) in front of a part number indicates a component required to construct the
More informationElectro - Hydraulics. & Pneumatics. Electro Hydraulic Press. Comparison. Electro Hydraulics. By: Alireza Safikhani
Electro - 9 Hydraulics & Pneumatics 2 Electro Hydraulic Press The hydraulic press is controlled via the electrical control panel. Electrical signals are used to activate the valves in the hydraulic installation.
More informationJIS symbols used in this catalog are old symbols following JISB0125-1: Refer to JISB0125-1: 2007 or JFPS2011: 2006 for new symbols.
symbol s used in this catalog are old symbols following JISB0-: 00. Refer to JISB0-: 007 or JFPS0: 006 for new symbols. Page. Element of symbol. Line and port. Directional control valve. Pressure control
More informationFLUID POWER FLUID POWER EQUIPMENT TUTORIAL PNEUMATIC CIRCUTS. This work covers part of outcome 3 of the Edexcel standard module:
FLUID POWER FLUID POWER EQUIPMENT TUTORIAL PNEUMATIC CIRCUTS This work covers part of outcome 3 of the Edexcel standard module: UNIT 21746P APPLIED PNEUMATICS AND HYDRAULICS The material needed for outcome
More information6080 Hydraulics Training System
6080 Hydraulics Training System LabVolt Series Datasheet Festo Didactic en 240 V - 50 Hz 03/2018 Table of Contents General Description 2 Innovative Design 3 Virtual Laboratory Equipment 3 Courseware 3
More informationFesto Modular Production System (MPS)
ELEC E8114 Manufacturing Automation Systems Modelling Festo Modular Production System (MPS) Figure 1 Distribution station (left) and testing station (right) 1 Introduction The purpose of this document
More informationTest. What type of cylinder would you use? A. Single-acting cylinder B. Double-acting cylinder Answer:
Test This test allows you to establish whether your basic knowledge of pneumatic controls is sufficient for you to attend the advanced course P or whether you should attend the basic level course P. The
More informationPneumatic Actuators. TGA Specifications
Pneumatic Actuators The TGA model is a double-action pneumatic actuator perfect for on/off control of the various types of butterfly valves. With an optional positioner, it can also be used for flow rate
More informationME 360 Test #3 Spring 08 5/5/08. Closed book, closed notes portion of test. Total of 25 out of 100 points for questions #1 to #6.
ME 360 Test #3 Spring 08 5/5/08 Closed book, closed notes portion of test. Total of 25 out of 100 points for questions #1 to #6. 1) [10] Mark the following true (T) or false (F) questions a) Pressure relief
More informationTable of Contents. Table of Contents UniTrain UniTrain courses UniTrain mechatronic courses IMS 23/24 with 3/4 subsystems
Table of Contents Table of Contents UniTrain UniTrain courses UniTrain mechatronic courses IMS 23/24 with 3/4 subsystems 1 2 2 3 4 Lucas Nülle GmbH Page 1/16 www.lucas-nuelle.com UniTrain UniTrain is a
More informationTRAILER MOUNTED PUMP MODEL B50 DRIVE CYLINDER CIRCUIT HYDRAULIC COMPONENTS & SCHEMATIC
DRIVE CYLINDER CIRCUIT HYDRAULIC COMPONENTS & SCHEMATIC PAGE 01 SINGLE SHIFT SWING TUBE CIRCUIT HYDRAULIC COMPONENTS & SCHEMATIC PAGE 02 DUAL SHIFT SWING TUBE CIRCUIT HYDRAULIC COMPONENTS & SCHEMATIC PAGE
More informationHydraulic and Electro-Hydraulic Application AE-HD
Engineering and Technical Teaching Equipment Hydraulic and Electro-Hydraulic Application AE-HD AE-HD. Hydraulic and Electro-Hydraulic Application INTRODUCTION Hydraulics is the technology that employs
More informationSECTION B1: MACHINE COMPONENTS
SECTION B1: MACHINE COMPONENTS The machine portion of the Injected Metal Assembly system provides the means for: holding, heating and injecting the alloy; distributing and controlling electrical, pneumatic,
More informationTECHNICAL PAPER 1002 FT. WORTH, TEXAS REPORT X ORDER
I. REFERENCE: 1 30 [1] Snow Engineering Co. Drawing 80504 Sheet 21, Hydraulic Schematic [2] Snow Engineering Co. Drawing 60445, Sheet 21 Control Logic Flow Chart [3] Snow Engineering Co. Drawing 80577,
More informationTraining systems for hydraulics. Edition:
Training systems for hydraulics Edition: 05.2017 2 Training systems for hydraulics Training systems for hydraulics 3 The 4 Learning topics 7 Term definition 11 Overview of the learning topics 12 Learning
More informationElectropneumatics Basic Level Set of Overhead Transparencies TP 201
Electropneumatics Basic Level Set of Overhead Transparencies TP 0 Festo Didactic 0950 en Order No.: 0950 Description: EL-PN.FOLIEN-GS Designation: D:OT-TP0-GB Edition: 0/000 Author: Frank Ebel Graphics:
More informationDiscrete Control Logic. 1. Pneumatic circuits. - Low forces - Discrete, fixed travel distances - Rotational or reciprocating motion
Discrete Control Logic 1. Pneumatic circuits - Low forces - Discrete, fixed travel distances - Rotational or reciprocating motion Main components: compressor, valves, cylinders Pneumatic components: cylinders
More informationLevel 7 Post Graduate Diploma in Engineering Mechatronics
9210-223 Level 7 Post Graduate Diploma in Engineering Mechatronics 0 You should have the following for this examination one answer book calculator (programmable calculators are not allowed) pen pencil
More informationTG-S Specifications TG-12S Rc3/8. 6 to 20
Pneumatic Actuators The TG-S type spring return pneumatic actuator is suitable for on/off control for medium and large sized valves. With an optional positioner, it can also be used for flow control. Air
More informationJanuary 2007 Approval Guide Fixed Extinguishing Systems 5-57
Fixed Extinguishing Systems 5-57 CHEMETRON Fire Systems, 4801 Southwick Dr, 3rd Floor, Matteson IL 60443 High Pressure System Equipment. Automatic Actuator. 1-026-02, -0250. Alarm. 1-003-0033, -0070, -0071,
More informationIndustrial Mechanic (Millwright) Level 3
Industrial Mechanic (Millwright) Level 3 Rev. September 2005 Industrial Mechanic (Millwright) Unit: G5 Prime Movers I Diesel 1 Level: Duration: Three 60 hours Theory: 20 hours Practical: 40 hours Overview:
More informationSAP E & C PLC PROGRAMMING TRAINER KIT (PRODUCT CODE: PCST 14)
SAP E & C PLC PROGRAMMING TRAINER KIT (PRODUCT CODE: PCST 14) PLC PROGRAMMING TRAINER KIT The applications and working modules of PLCs which are optionally hooked up with PLC Programming Trainer Kit (PCST
More informationAppendix A. Standard Symbols for Hydraulic Components
Table B.1 Flow lines Appendix A Standard Symbols for Components Continuous flow E Pilot connection L L>10E E Drain connection L L
More informationMCD Pump Application Module
Overview The Pump Application Module expands the soft starter's input and output functionality and is ideal for applications where greater control and feedback are required. The module provides three digital
More informationICG Switchgear Price List 2009
ICG Switchgear Price List 2009 Section 1 Control Gear Page Contactors (AC,DC & Modular) 2,3 Overload Relays 4 Product Accessories 4,5 Starters-DOL, Star-Delta, Fan/Vibrators, Reversing/Twin 6,7 Section
More informationROBOTICS SAFETY MOTION & CONTROL. SENSORS, VISION & IIoT PNEUMATICS ELECTRICAL
MOTION & CONTROL ROBOTICS SAFETY SENSORS, VISION & IIoT PNEUMATICS ELECTRICAL Cedarburg Headquarters 7400 Quail Court P.O. BOX 860 Cedarburg, WI 53012 Weston Branch 4601-A Camp Phillips Rd Weston, WI 54476
More informationSDigital vs. Analog Sensors
How Sensors Are Used in Fluid Power Systems Sensors are used as input devices in fluid power systems to indicate that a condition has been, or has not been, met. Sensors can be used to monitor pressure,
More informationPneumatic Power Valves Series 75/76 Manual, Mechanical, Pneumatic and Electric Valves
Quic-Pics Catalogue Pneumatic Power Valves Series 75/76 Manual, Mechanical, Pneumatic and Electric Valves Contents: Product Line Overviews 2 Manually Operated Valves 5 Pushbuttons 6 Toggle Switch 8 Knob
More informationMechatronics systems
Mechatronics systems www.matrixtsl.com 1 HP4550 Solution Description This solution contains products from our Locktronics, E-blocks and Automatics ranges. The pack includes a wide variety of resources
More informationHydraulic pump HP-1. Type 1. Type 2
The BEKA-MAX central lubrication pump model HP-1 is hydraulic actuated and has up to a maximum of independently operating lubricant outlets. A separate pump unit is required for each outlet. Three pump
More informationControl unit for valves with inflatable sealing system
Control unit for valves with inflatable sealing system Type ICS A model from the system -vacotrol Shut-off valves are used in transport equipment for bulk powder and granulate, whose shut-off mechanism
More informationMechatronics. Training Systems. Pneumatics/Electro-pneumatics, PLC, Hydraulics/Electro-hydraulics, Mechanical Transmission
Mechatronics Training Systems Pneumatics/Electro-pneumatics, PLC, Hydraulics/Electro-hydraulics, Mechanical Transmission Tutor Kits Pneumatics Trainers Hydraulics Trainers Courseware/Teachware Mechanical
More informationPneumatic Cylinder. 3I Double-acting type. 3Q Single-acting type (spring returned type)
Pneumatic Cylinder State of the art in actuation, Tomoe cylinders offer compactness, lighter weight, and higher output torque. I Double-acting type Q Single-acting type (spring returned type) Features
More informationHAFNER Pneudactic Pneumatic Training Sets
HAFNER Pneudactic Pneumatic Training Sets Page 2 HAFNER pneudactic The HAFNER pneudactic training sets have been developed to educate students or employees in the basics of the use of pneumatic components
More informationHydraulics and Pneumatics Simulation Software (LVSIM -HYD & PNEU) - 1 User
6387-00 Hydraulics and Pneumatics Simulation Software (LVSIM -HYD & PNEU) - User LabVolt Series Datasheet Festo Didactic en 02/208 Table of Contents General Description 2 Topic Coverage 2 Features & Benefits
More informationIndustrial Controls Training Systems
Industrial Controls Training Systems LabVolt Series Datasheet Festo Didactic en 220 V - 50 Hz 04/2018 Table of Contents General Description 2 Integration into 8001 and 8006 Electromechanical Training Systems
More informationDC3N Non-Regenerative DC Drives
PRICING 1/8-1.0 HP @ 115 VAC, 1-Ph, 50/60 Hz: 90 VDC Armature 1/4-2.0 HP @ 230 VAC, 1-Ph, 50/60 Hz: 180 VDC Armature For the Operation of Permanent Magnet DC Motors Only Product Features: DC3N Plate Model
More informationTransmitters: Relay Valve VR4151/4152
Relay Valve VR4151/4152 Appropriate output sequences are affected according to the signal received from the mechanical valve. VR4151 VR4152 Precautions Be sure to read before handling. Refer to pages 5-11-2
More informationCONTROLS. Bray Pneumatic Actuators & Accessories. Technical Manual. A Division of BRAY INTERNATIONAL, Inc.
CONTROLS A Division of BRAY INTERNATIONAL, Inc. Bray Pneumatic Actuators & Accessories Technical Manual TM-056 Pneumatic Actuator - 08//00 Bray Pneumatic Actuators & Accessories Technical Manual - Table
More informationV Series AXIAL PISTON PUMP ORDER CODE
V Series AXIAL PISTON PUMP ORDER CODE V A 1 R B S - A D X A 1 Customers demand Pump Series V Links Type (only V -18): none - Standard A - SAE A bolts Ma. (cm 3 /n):, 18, 3,, 38, 4,, 7 Pump Control Type
More informationChapter 6 Pneumatic Logic Sensors and Actuators
Chapter 6: Penumatic logic sensors and actuators -IE337 Chapter 6 Pneumatic Logic Sensors and Actuators 1 Introduction to Pneumatic Why pneumatic? Pneumatic control system is frequently used in building
More informationCourseware Sample F0
Fluid Power Pneumatics Courseware Sample 31290-F0 ü FLUID POWER PNEUMATICS COURSEWARE SAMPLE by the Staff of Lab-Volt (Quebec) Ltd Copyright 1999 Lab-Volt Ltd All rights reserved. No part of this publication
More informationEngel Injection Molding Machine VERTICAL CLAMP INSERT 330V/90 WP US. Data Sheet INSERT 330V/90 WP US - VERTICAL CLAMP / VERTICAL INJECTION
Engel Injection Molding Machine INSERT 330V/90 WP US - VERTICAL CLAMP / VERTICAL INJECTION CLAMP Clamp force US tons 90 Clamp opening force US tons 3.0 Clamp stroke (max.) inches 13.78 Mold height (min
More informationDamper Seal Kit Seal Kit Strainer Seal kit Seal Kit Element
www.westxl.com Sandvik Parts Part No. Description Qty Available 00290840 Gasket 3 00298830 Gasket 5 00641800 Plug pito jaw 2 00668970 Spacer 4 00668980 Shim 2 00669000 Shim 2 00670210 Handle 1 00670370
More informationV Series AXIAL PISTON PUMP ORDER CODE
V Series AXIAL PISTON PUMP ORDER CODE V 15 A 1 R B S - A 1 D X A 11 Customers demand Pump Series V Links Type (only V 15-18): none - Standard A - SAE A 2 bolts Ma. Displacement (cm 3 /n): 15, 18, 23, 25,
More information35 35A 50 50A 1 Single phase. Solid state power controller
Single Phase, Power Controller Single Phase, Power Controller Features Various and simple input specification DC4-2mA, 1-5VDC, External 24VDC External adjuster (1kΩ) External contact (ON/OFF) Various function
More informationHANDS-ON INDUSTRIAL TRAINING FLUID SENSORS SIMULATION SOFTWARE E-LEARNING CERTIFICATION PREPARATION
HANDS-ON INDUSTRIAL TRAINING FLUID SENSORS SIMULATION SOFTWARE E-LEARNING CERTIFICATION PREPARATION Innovative Design Offers Exceptional Options Lab-Volt offers the most comprehensive and flexible course
More informationUniversal Fluid Power Trainer (UFPT)
Universal Fluid Power Trainer (UFPT) The UFPT is a modular, smart and unique fluid power and motion control training unit. It contains an excellent integration of industrial-graded hardware and builtin
More information3.10 Air Conditioning (A/C) Contents
3.10 Air Conditioning (A/C) Contents 3.10 Model 208 as of M.Y. 1998 Diagnosis Page Function Test................................... 11/1 Reading Actual Values............................ 12/1 Version Code...................................
More informationMECHATRONICS LAB MANUAL
MECHATRONICS LAB MANUAL T.E.(Mechanical) Sem-VI Department of Mechanical Engineering SIESGST, Nerul, Navi Mumbai LIST OF EXPERIMENTS Expt. No. Title Page No. 1. Study of basic principles of sensing and
More informationSECTION B: SYSTEM OPERATING COMPONENTS
SECTION B: SYSTEM OPERATING COMPONENTS A brief description of the machine, Cable Processor Module and tooling will provide a better understanding of the various functions of the IMA system. SECTION B1:
More informationUniversal Fluid Power Trainer (UFPT)
Universal Fluid Power Trainer (UFPT) Milwaukee School of Engineering Applied Technology Center TM Department of Professional Education The UFPT is a modular, smart and unique fluid power and motion control
More informationLEARNING ACTIVITY PACKET MECHATRONICS AUTOMATION OPERATIONS B72001-AA01UEN
MECHATRONICS LEARNING ACTIVITY PACKET AUTOMATION OPERATIONS B72001-AA01UEN LEARNING ACTIVITY PACKET 1 AUTOMATION OPERATIONS INTRODUCTION As manufacturing industries strive to be successful in a highly
More informationSafety Considerations
Safety Considerations The following safety rules MUST BE FOLLOWED to ensure safety in the laboratory. General Considerations No smoking, eating or drinking in the laboratory. Hydraulic oil in its vapor
More informationElectric pump EP-1. Electric pump with 1.9 kg reservoir:
The BEKA-MA central lubrication pump model EP-1 is electrically actuated and has up to a maximum of independently operating lubricant outlets. A separate pump element is required for each outlet. Three
More informationELECTROPNEUMATIC POSITIONING SYSTEM CONTROL WITH THE LEGENDARY LOGO! PLC
ELECTROPNEUMATIC POSITIONING SYSTEM CONTROL WITH THE LEGENDARY LOGO! PLC G. Kozoris Dept. of Automation Engineering, PUAS, Athens, Greece M. Papoutsidakis Dept. of Automation Engineering, PUAS, Athens,
More informationVacuum Automation 2.1. The future depends on good product choices
Vacuum Automation 2.1 The future depends on good product choices Optimising controls 458 459 Optimising controls Introduction...460 Vacuum switches...462 Valves...478 Regulators...488 Automatic energy
More informationAUTOMATION Products
AUTOMATION Products - 2014 An ISO 9001-2008 Company www.electronicswitchesindia.com www.electronicswitches.in Infra Red Diffuse Scan Sensors Page 3 Infra Red Retro-reflective Sensors Page 4 IR Sensors
More informationPneumatic. PVD Everdure Ceramic Valves
PVD Ceramic Valves Ceramic slide plate; extremely long life Built in manual override Transfer modules to combine all sizes Selectable air pilot control Clip-on DIN rail Specification Material Polyamide
More information