CULTIVATOR ASSEMBLY AND PARTS MANUAL

Transcription

1 CULTIVATOR ASSEMBLY AND PARTS MANUAL НАШ АДРЕС ООО «ТехАгроПарк» 966 Воронежская обл., Новоусманский р-н, п. Отрадное, ул. Автодорожная 7. (трасса М «Дон» 59 км пост ГАИ) Тел./ факс 8 (7) info@texagropark6.ru Лесных Павел Владимирович Тел lpv080@mail.ru lpv@texagropark6.ru Подбор запасных частей на сайте:

2 Table of Contents General Information Salford Recommended Torque Values...5 Wheel Torque Specifications...6 Tire Pressure Ratings....7 General Safety Precautions...8 Cylinder Series Identification Guide...0 Frame & Tongue Wing Installation....2 S-Tine Frontbar Installation... C-Shank Frontbar Installation...6 Tripod Installation....9 Tripod Assembly Tongue Installation Telescope Mount Hose Holder...2 Axles Wheel & Axle Layout LB Mainframe Axle Installation LB Wing Axle Installation LB Axle Assembly LB Hub & Spindle Assembly...2 S-Tine and Shanks S-Tine Assembly.... S-Tine Installation for Tight Spots...5 C-Shank Assembly and Parts...6 C-Shank Head Assembly and Parts...8 Layouts 2ft C-Shank Layout ft C-Shank Harrow Layout (/2 Inch Tines)... 2ft S-Tine Layout ft S-Tine Harrow Layout (/2 Inch Tines)... 7ft C-Shank Layout.... 7ft C-Shank Harrow Layout (/2 Inch Tines)...5 7ft S-Tine Layout ft S-Tine Harrow Layout (/2 Inch Tines)...7 9ft C-Shank Layout ft C-Shank Harrow Layout (/2 Inch Tines)...9 9ft S-Tine Layout ft S-Tine Harrow Layout (/2 Inch Tines)...5 2ft C-Shank Layout ft C-Shank Harrow Layout (/2 Inch Tines)...5 2ft S-Tine Layout ft S-Tine Harrow Layout (/2 Inch Tines)...55 Подбор запасных частей на сайте:

3 2ft C-Shank Layout ft C-Shank Harrow Layout (/2 Inch Tines) ft S-Tine Layout ft S-Tine Harrow Layout (/2 Inch Tines) ft C-Shank Layout ft C-Shank Harrow Layout (/2 Inch Tines) ft S-Tine Layout ft S-Tine Harrow Layout (/2 Inch Tines)...6 Harrow Parts S-Tine Harrow Installation...6 C-Shank Harrow Installation Harrow Arm Assembly...68 Tine Harrow Assembly Roller Assembly...72 Roller Assembly...7 Lights & Hydraulics 2 Axle Lift Hydraulics Axle Lift Hydraulics Wing Fold Hydraulics...80 Lights, SMV & Parking Stand Install...82 Decals Decal Locations...86 Tow Hitch Optional Tow Hitch Installation Page

4 NOTES Подбор запасных частей на сайте: Page

5 General Information 6$/)25' Salford Recommended 5(&200('(' Torque 7258( Values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age VLGHV RI WKH XEROW 'R QRW WLJKWHQ RQH VLGH RI WKH PXVW EH WLJKWHQHG HTXDOO\ XEROW EHIRUH WKH RWKHU VLGH Подбор запасных частей на сайте: Page 5

6 Wheel Torque Specifications WARNING Maintain proper torque to provide safe and secure attachment of the wheel hub/drum. Improperly tightened wheel nuts can cause the wheel to separate from the wheel mounting surface during operation. This could result in property damage, serious personal injury, or possibly loss of life. NOTE - If wheel does not have chamfers to match profile of the nuts, use flat side of nuts against rim face. Install all lug nuts/bolts by hand to prevent cross threading and tighten lug nuts/bolts following the steps and tightening sequence diagram below. STEP ) Torque to ft lbs following the appropriate pattern below. STEP 2) Torque to ft lbs following the appropriate pattern below. STEP ) Torque to final ft lbs rating (see bolt size below) following the appropriate pattern below. Bolt Size (Hub Size) Final Torque /2 dia. bolt (up to 000 lb hubs) 85 ft lbs 9/6 dia. bolt ( lb hubs) 20 ft lbs 5/8 dia. bolt ( lb hubs) 70 ft lbs / dia. bolt ( lb hubs) 00 ft lbs 7/8 dia. bolt (25000 lb hubs) ft lbs Lug Nut/Bolt Tightening Sequence 6 LUG BOLT PATTERN 8 LUG BOLT PATTERN 0 LUG BOLT PATTERN NOTE - Recheck the torque settings of lug nuts/bolts after 0km (6 miles) and again after 50km (0 miles). Periodically and at the beginning of each season check the condition and the torque of the lug nuts/bolts. Page

7 Tire Pressure Ratings Ensure proper inflation of each tire for safe operation and extended tire life. Pressure [psi] Pressure [bar] Tire Size 25 [psi].72 [bar] 2. x 26 (6 ply) 0 [psi] 2.07 [bar] 5 x 9.5 Lug Tire (6 ply) 5 [psi] 2. [bar] Load Range C - L5 6 [psi] 2.8 [bar] 28L26 (6 ply) 52 [psi].58 [bar] 0.5LR2 (8A8/B) 65 [psi].8 [bar] Load Range D - L5-2.5L5 70 [psi].8 [bar] 5 x 9.5 Lug Tire ( ply) 90 [psi] 6.20 [bar] Load Range F - L5-2.5L5 Truck Tires - 25/70R /70R /60R22-5 NOTE - Periodically and at the beginning of each season check the condition and the pressure of each tire. Tire Installation Direction Measure both sides of tire in to rim face. Install the deep side in or out according to the instructions below. If bolts/nuts are coned, ensure proper seating in chamfer on rim. Deep Dish Deep dish Tires to install deep dish out: 2.5L 05 5 x 9.5 Tires to install deep dish in: L Do not rely on valve stem for orientation of tires. It may face in or out on different rims Page 7

8 General Safety Precautions Signal Words The words DANGER, WARNING or CAUTION are used with the safety alert symbol. Learn to recognize the safety alerts, and follow the recommended precautions and safe practices. Three words are used in conjunction with the safety-alert symbol: DANGER WARNING CAUTION Indicates an imminently hazardous situation that, if not avoided, will cause DEATH OR VERY SERIOUS INJURY. Indicates a potentially hazardous situation that, if not avoided, could cause DEATH OR SERIOUS INJURY. Indicates a potentially hazardous situation that, if not avoided, may result in MINOR or MODERATE INJURY. Replace any DANGER, WARNING, CAUTION or instructional decal that is not readable or is missing. The location and part number of these decals is identified later in this section of the manual. The words Important and Note are not related to personal safety but are used to give additional information and tips for operating or servicing this equipment. IMPORTANT: Identifies special instructions or procedures which, if not strictly observed could result in damage to, or destruction of the machine, process or its surroundings. NOTE: Indicates points of particular interest for more efficient and convenient repair or operation. A CAREFUL OPERATOR IS THE BEST INSURANCE AGAINST AN ACCIDENT! Подбор запасных частей на сайте: Page

9 General Safety Precautions DANGER Wings may fall rapidly causing injury. Always stay clear of wings when being lowered, raised or in a elevated state. Always use lockup device provided when raised. Ensure cylinder is completely filled with hydraulic fluid to avoid unexpected movement. Hydraulics DANGER DO NOT search for high pressure hydraulic leaks without hand and face protection. A tiny, almost invisible leak can penetrate skin, thereby requiring immediate medical attention. Use cardboard or wood to detect leaks never your hands. Double check that all is clear before operating hydraulics. Never remove hydraulic hoses or ends with machine elevated. Relieve hydraulic pressure before disconnecting hydraulic hoses or ends. Maintain proper hydraulic fluid levels. Keep all connectors clean for positive connections. Ensure all fittings and hoses are in good condition. Do not stand under wings. General O Подбор запасных частей на сайте: Page 9

10 Cylinder Series Identification Guide SALFORD HYDRAULIC CYLINDER INDENTIFICATION GUIDE SALFORD ORIGINAL SERIES HSXXXX AND HSRXXXX PART NO. STAMP MACHINED END-CAPS THREADED TO BARREL PORTS MACHINED IN GLAND AND END-CAP ROD ENDS THREADED TO ROD SALFORD 'A' SERIES - WING FOLD ONLY HSXXXXA WELDED END-CAP W/ WELDED EARS PART NO. STAMP ROD END WELDED TO ROD PORTS WELDED TO BARREL Подбор запасных частей на сайте: Page

11 Cylinder Series Identification Guide SALFORD 'B' SERIES* HSXXXXB AND HSRXXXXB (MANUFACTURER PART NO. SFXXXXXX) FORGED CLEVIS STYLE ROD ENDS WELDED TO ROD CROSS TUBE STYLE ROD ENDS WELDED TO ROD PORTS MACHINED IN GLAND AND ENDCAP SET SCREW FOR PORT POSITION ADJUSTMENT *REQUIRED /8 LONG OR LONGER PINS FORGED END-CAPS WELDED TO BARREL PART NO. STAMP SALFORD 'C' SERIES HCXXXX AND HCRXXXX (MANUFACTURER PART NO. XXTXXX-XXX) TIE-ROD STYLE BODY PART NO. LABEL WELED CAP BYPASS PORT - HRCXXXX ONLY Page

12 Frame & Tongue Wing Installation 8 0 Refer to 7'-25' Wing Fold Hydraulics for cylinder sizes Hard bushings 5 are pressed into wing hinges Page

13 Wing Installation ITEM QTY PART NO. DESCRIPTION 2 C '-2' WING LOCK 2 2 GP6007C0 x 7 / HITCH PIN 2 GP20006A06 / x 6 PIN - 2 HOLES 2 GPHF20002H05 / x /2 SHOULDER PIN HARDENED W/ FLATS 5 GPH2008F /2 x 8 / LG. HARD PLATE PIN 6 2 GHP9 #9 HAIR PIN 7 BSC0620 /8 x 2 COTTER PIN 8 2 BSC0520 5/6 x 2 COTTER PIN 9 B05 5/8NC x /2 HEX BOLT 0 BU080 /2 x x / U-BOLT BF20S / SAE WASHER 2 BL0 5/8 LOCKWASHER 8 BN08L /2 NYLOCK NUT NC GF6 /8 NPT GREASE FITTING 90deg 5 8 GBB / x /2 x LG. HARD BUSHING Refer to 7'-25' Wing Hydraulics page for cylinder sizes. ROD PORT CANNOT FACE UPWARD OR IT WILL COLLIDE WITH WING WHEN FOLDED. PORTS SHOULD FACE THE CENTER OF THE MACHINE IMPORTANT PURGE ALL AIR FROM SYSTEM BEFORE FOLDING. REFER TO 50 WING FOLD HYDRAULICS PAGE FOR INSTRUCTIONS Page

14 S-Tine Frontbar Installation Page

15 S-Tine Frontbar Installation ITEM NO. 2'/QTY. 7'/QTY. 9'/QTY. 2'/QTY. 2'/QTY. 25'/QTY. PART NO. DESCRIPTION B00 5/8 x HEX BOLT GR 5 2 BU06 U-BOLT 5/8 x x 7 /2 LG BU06 U-BOLT 5/8 x 6 x 5 / BF0HS 5/8 HARD STRUCTURAL FLAT WASHER BN0L 5/8 NYLOCK NUT NC BU062 U-BOLT 5/8 x 6 x / BU020 5/8 x 2 x /2 U-BOLT BU05 U-BOLT 5/8 x x /2 9 C MAIN MIDDLE 5TH BAR 0 C02R 50 S-TINE MAIN OUTER 5TH BAR - RH C02L 50 S-TINE MAIN OUTER 5TH BAR - LH C ' S-Tine WING Front Bar C /2' S-TINE WING 5TH BAR C /25' S-TINE WING 5TH BAR C025 5TH BAR BOLT-ON EXTENSION C078 0 BOLT-ON STUB Подбор запасных частей на сайте: Page 5

16 C-Shank Frontbar Installation Page

17 C-Shank Frontbar Installation ITEM NO. 2'/QTY. 7'/QTY. 9'/QTY. 2'/QTY. 2'/QTY. 25'/QTY. PART NO. DESCRIPTION BF0HS 5/8 HARD STRUCTURAL FLAT WASHER B00 5/8 x HEX BOLT GR 5 BU06 U-BOLT 5/8 x x 7 /2 LG BU06 U-BOLT 5/8 x 6 x 5 / BN0L 5/8 NYLOCK NUT NC BU020 5/8 x 2 x /2 U-BOLT BU05 U-BOLT 5/8 x x /2 8 C MAIN MIDDLE 5TH BAR 9 C0995L 50 C-SHANK MAIN OUTER 5TH BAR - LH 0 C0995R 50 C-SHANK MAIN OUTER 5TH BAR - RH C05L 50-7' WING 5TH BAR LH C05R 50-7' WING 5TH BAR RH C0996L 50-9'/2' C-SHANK WING 5TH BAR - LH C0996R 50-9'/2' C-SHANK WING 5TH BAR - RH C08L 50-2'/25' WING 5TH BAR C08R 50-2'/25' WING 5TH BAR C025 5TH BAR BOLT-ON EXTENSION Подбор запасных частей на сайте: Page 7

18 Подбор запасных частей на сайте: Page

19 Tripod Installation , 550, 700 0' 700 ' - 50' * ** ITEM QTY PART NO. DESCRIPTION C /570/699/700 TRIPOD TOWER 2 C TRIPOD BRACE 5 B025 5/8 x 2 /2 HEX BOLT GR 5 2 B00 5/8NC x LG. HEX BOLT 5 5 BN0S 5/8 NC STOVER LOCK NUT 6 2 GP6006A05 PIN DIA. x 6 / LG. - 2 HOLES 7 BSC055 5/6 x /2 COTTER PIN 8 GM26 MACHINE BUSHING * Quantity shown for 50, 550, and 700 0' machines. Quantity of for 700 '-50' machines. ** Used only on 700 '-50' Machines. Подбор запасных частей на сайте: Page 9

20 Tripod Assembly SEE HYDRAULIC LAYOUT Page

21 Tripod Assembly ITEM QTY. PART NO. DESCRIPTION C /570/699/700 TRIPOD TOWER 2 2 GBB / x /2 x 2 LG. HARD BUSHING C /570/699/700 SELF-LEVELING PIVOT 2 GF60 /8 NPT GREASE FITTING 5 GP20002A05 / DIA. x 0 /2 LG - 2 HOLE 6 2 BSC0520 5/6 x 2 COTTER PIN 7 2 GM0 / MACHINE BUSHING 8 GP205A09 PIN /2 DIA. x 5 / LG. - 2 HOLES 9 2 B080 /2 x HEX BOLT 0 2 BN08L /2 NYLOCK NUT NC 2 GPHF6008H0 x /8 SHOULDER PIN HARDENED W/FLATS 2 2 BSC05 / x /2 COTTER PIN D00C /2 X 2 FB- / LG: POPPET VALVE BRACKET 7 C DEPTH CONTROL ROD 5 HPMSC0 STROKE CONTROL VALVE 6 BU00 U-BOLT 5/8 x x /2 7 2 BN0L 5/8 NYLOCK NUT NC 8 2 B0525 5/6NC x 2 /2 HEX BOLT 9 2 BN05L 5/6 LOCK NUT 20 C008 DEPTH CONTROL DISC ASSEMBLY NOTE: WHEN INSTALLING POPPET VALVE BRACKET, TIGHTEN THE U-BOLT EQUALLY. DO NOT OVERTIGHTEN!! Подбор запасных частей на сайте: Page 2

22 Tongue Installation Torque 0 & 2 to ft/lbs OPTIONAL: CHANGE WITH 7 CAT CLEVIS Place pin 5 through last ring of Page

23 Tongue Installation USED ONLY WITH CAT # OPTION + ++ ITEM QTY PART NO. DESCRIPTION 2225C CAST CLEVIS TONGUE 2 C0592A 72 OUTER TELESCOPE A INNER TELESCOPE 2 BN0L 5/8 NYLOCK NUT NC 5 2 GPSPEC2080 /2 x 8 / LG. WING HINGE PIN 6 A5000 TURNBUCKLE 7 PPI-2XL CAT CAST IRON HITCH 8 PPI-0XL CAT # CAST CLEVIS 9 PPI-208VR CLEVIS FOR CAT HITCH 0 B255H / x 5 /2 HEX BOLT GR. 8 2 BF2HS / HARD STRUCTURAL WASHER 2 BN2S / STOVER LOCK NUT 2 B680H x 8 NC HEX BOLT GR. 8 2 BN6C - UNC STOVER LOCKNUT 5 GP60052A05 PIN DIA. x 5 /2 LG. - 2 HOLES 6 2 BSC055 5/6 x /2 COTTER PIN 7 2 BSC05 / x /2 COTTER PIN 8 2 BF6S SAE WASHER 9 2 GP600258H0 PIN DIA. x 2 5/8 LG. WITH HEAD 20 GF6 /-28NF GREASE FITTING 2 GP200062B06 / x 6 /2 LG. PIN - HOLE 22 B0625 /8 X 2 /2 LG. GRADE 5 2 BN06L /8-6NC LOCK NUT 2 GJ LB TONGUE JACK 25 GJ5000S 5000lb JACK WITH ROUND MOUNT 26 GP00C0 5/8'' DIA x /'' PIN RING & WASHER 27 GHP # HAIR PIN 28 GJ ,000 LB SAFETY CHAIN 29 A60096A TELESCOPE MOUNT HOSE HOLDER ASSEMBLY 0 2 BU080 /2 x x / U-BOLT BN08L /2 NYLOCK NUT NC 2 BF08HS /2 HARD STRUCTURAL FLAT WASHER BF6HS HARD STRUCTURAL WASHER + Used on 8ft to 50ft machines ++ Used on 2ft and under machines Подбор запасных частей на сайте: Page 2

24 Telescope Mount Hose Holder ITEM QTY PART NO. DESCRIPTION A60096 TELESCOPE MOUNT HOSE HOLDER 2 G06 HD OPERATORS MANUAL HOLDER GL750 LIGHT PLUG HOLDER - PLASTIC P060B HOSE CLAMP 5 2 BC060 /8NC x LG. CARRIAGE BOLT 6 2 BN06L /8-6NC LOCK NUT 7 2 BF0 / FLATWASHER 8 5 BC x /2 A07A LOW CARBON ZINC CARRIAGE BOLT 9 5 BN02L #0-2 NYLOCK NUT 0 2 BU080 /2 x x / U-BOLT BN08L /2 NYLOCK NUT NC 2 BF08HS /2 HARD STRUCTURAL FLAT WASHER 9 Extra clamps for use on machines requiring more than two sets of hoses Page

25 Axles WING AXLES -5000LB TANDEM AXLES -000LB HUBS -HSR208 CYLINDER -L x 5SL TIRES LOAD RANGE 'C' (GW56) 7' MODEL HAS SINGLE WHEEL ON WINGS -OPTIONAL L x 5SL TIRES LOAD RANGE 'D' (GW56H8) Wheel & Axle Layout MAIN AXLES & 2' MACHINES -5000LB TANDEM AXLES -000LB HUBS -HSR508 CYLINDER -L x 5SL TIRES LOAD RANGE 'C' (GW56) -OPTIONAL L x 5SL TIRES LOAD RANGE 'D' (GW56H8) WING AXLES -5000LB TANDEM AXLES -000LB HUBS -HSR208 CYLINDER -L x 5SL TIRES LOAD RANGE 'C' (GW56) 7' MODEL HAS SINGLE WHEEL ON WINGS -OPTIONAL L x 5SL TIRES LOAD RANGE 'D' (GW56H8) RH AXLE ASSEMBLY S-TINE MODEL LH AXLE ASSEMBLY FRONT LH AXLE ASSEMBLY NOTE: 2' C-SHANK AXLES SAME AS S-TINE (LEADING TIRE TO OUTSIDE OF MACHINE) C-SHANK MODEL RH AXLE ASSEMBLY Page 25

26 5000LB Mainframe Axle Installation Refer to hydraulic layout page for cylinder size S-Tine 65 Initial setting pin to pin 7 C-Shank 6 Initial setting pin to pin 6 L-pin not needed for turnbuckle locks on mainframe COMPLETE ASSEMBLY LH SHOWN, RH SIMILAR Подбор запасных частей на сайте: Page

27 5000LB Mainframe Axle Installation C-SHANK S-TINE C-SHANK S-TINE ITEM QTY PART NO. DESCRIPTION C50L 5000 LB MAIN AXLE ASSEMBLY - LH 2 C50R 5000 LB MAIN AXLE ASSEMBLY - RH C00L 5000 LB S-TINE MAIN AXLE ASSEMBLY - LH C00R 5000 LB S-TINE MAIN AXLE ASSEMBLY - RH 5 C00 MAIN FRAME TOWER 6 A600 2 /2 TURNBUCKLE 50 TUBE 7 A /2 TURNBUCKLE 5 TUBE 8 C5000 TRANSPORT LOCK ASSEMBLY 9 C076 2 /2 TURNBUCKLE LOCK 0 GP600C0 x / RING & WASHER PIN GPH200F / x /2 LG. AXLE PIN - HARDENED 2 2 GP200052A05 / x 5 /2 PIN - 2 HOLES BSC0520 5/6 x 2 COTTER PIN GM0 / MACHINE BUSHING 5 GP6005A05 PIN DIA. x 5 LG. - 2 HOLES 6 2 BSC055 5/6 x /2 COTTER PIN 7 2 GPHF6008H0 x /8 SHOULDER PIN HARDENED W/FLATS 8 BSC05 / x /2 COTTER PIN 9 GP600258H0 PIN DIA. x 2 5/8 LG. WITH HEAD 20 B05 5/8 X /2 PLATED BOLT 2 BL0 5/8 LOCKWASHER 22 GHP9 #9 HAIR PIN 2 B085 /2 X /2 BOLT 2 BN08L /2 NYLOCK NUT NC 25 2 GM26 MACHINE BUSHING 26 GW000A 000 LB HUB AND SPINDLE ASSEMBLY 27 2 GBB /2 x / x LG. HARD BUSHING 28 2 GBB / x /2 x 5/8 LG. HARD BUSHING 29 2 GBB / x x LG. HARD BUSHING 0 2 GBB /2 x / x 2 LG. HARD BUSHING GBB / x x.860 LG. HARD BUSHING 2 2 GBB /2 x / x 5/8 LG. HARD BUSHING CAUTION Connect hoses and charge lift axle cylinders with fluid following the procedure in the hydraulics installation before connecting rod ends of the cylinders. Check: Wheel nuts/lugs for proper tightness. (See torque & pressure values on tire page) Подбор запасных частей на сайте: Page 27

28 5000LB Wing Axle Installation 7 5 C-Shank - 67 Initial setting pin to pin S-Tine - 62 / Initial setting pin to pin Refer to hydraulic layout page for cylinder size COMPLETE ASSEMBLY LH SHOWN, RH SIMILAR C-Shank S-Tine ' ONLY Page

29 5000LB Wing Axle Installation S-TINE C-SHANK 50-7' S-TINE & C-SHANK C-SHANK S-TINE S-TINE C-SHANK ITEM QTY PART NO. DESCRIPTION C002WR-KIT 5000 LB S-TINE WING AXLE ASSEMBLY - RH 2 C002WL-KIT 5000 LB S-TINE WING AXLE ASSEMBLY - LH C50WR-KIT 5000 LB WING AXLE ASSEMBLY - RH C50WL-KIT 5000 LB WING AXLE ASSEMBLY - LH 5 C05L-KIT 7' CULTIVATOR AND 8' RTS RH SINGLE WHEEL AXLE 6 C05R-KIT 7' CULTIVATOR AND 8' RTS RH SINGLE WHEEL AXLE 7 C57B TOWER,50/550/570 WING 8 GPH200F / x /2 LG. AXLE PIN - HARDENED 9 BL0 5/8 LOCKWASHER 0 B05 5/8 X /2 HEX BOLT GR. 5 BN0L 5/8 NYLOCK NUT NC 2 A60025 / TURNBUCKLE TUBE A60020 / TURNBUCKLE 5 TUBE FL0005 LIGHT TURNBUCKLE LOCK 5 GP600H0 PIN DIA. x / LG. WITH HEAD 6 GP600258H0 PIN DIA. x 2 5/8 LG. WITH HEAD 7 BSC05 / x /2 COTTER PIN 8 GP08002L0 /2 x /2 L - PIN 9 GHP # HAIR PIN 20 2 GPHF6008H0 x /8 SHOULDER PIN HARDENED W/FLATS 2 2 GW000A 000 LB HUB AND SPINDLE ASSEMBLY 22 2 B085 /2 X /2 BOLT 2 2 BN08L /2 NYLOCK NUT NC 2 2 GBB /2 x / x /2 LG. HARD BUSHING 25 GBB /2 x / x LG. HARD BUSHING 26 GBB / x x LG. HARD BUSHING 27 2 GBB /2 x / x 2 LG. HARD BUSHING 28 GBB / x x.860 LG. HARD BUSHING Quantities for one wing only, double quantities shown per machine CAUTION Connect hoses and charge lift axle cylinders with fluid following the procedure in the hydraulics installation before connecting rod ends of the cylinders. Check: Wheel nuts/lugs for proper tightness. (See torque & pressure values on tire page) Подбор запасных частей на сайте: Page 29

30 LH RH 7 8 S-TINE 6 C-SHANK For wings MAIN LH 0 MAIN RH WING LH & RH 2 26 Items 2-8 not sold as individual parts, only sold as complete repair kits shown 25, 26, & LH RH S-TINE 2 C-SHANK For mainframes LB Axle Assembly Page

31 5000LB Axle Assembly ITEM NO. QTY PART NUMBER DESCRIPTION C52L-KIT 5000 LB MAIN UPRIGHT AXLE - LH 2 C52R-KIT 5000 LB MAIN UPRIGHT AXLE - RH C005L-KIT 5000 LB S-TINE MAIN UPRIGHT AXLE - LH C005R-KIT 5000 LB S-TINE MAIN UPRIGHT AXLE - RH 5 C52WL-KIT 5000 LB WING UPRIGHT AXLE - LH 6 C52WR-KIT 5000 LB WING UPRIGHT AXLE - RH 7 C00WL-KIT 5000 LB S-TINE WING UPRIGHT AXLE - LH 8 C00WR-KIT 5000 LB S-TINE WING UPRIGHT AXLE - RH 9 C5L 5000 LB MAIN WALKING BEAM - LH 0 C5R 5000 LB MAIN WALKING BEAM - RH C LB WALKING BEAM FOR WINGS 2 GW50VW 5000/5500 LB V-SEAL GRASS WRAP GUARD GW50VS 5000/5500 LB V-SEAL GW50VC 5000/5500 LB SEAL COUNTERFACE 5 GB /5500 LB INNER CONE 6 GB /5500 LB INNER CUP 7 GB /5500 LB OUTER CUP, 000 LB INNER CUP 8 GB /5500 LB OUTER CONE, 000 LB INNER CONE 9 BF6-9 HARD SAE FLAT WASHER GR.9 PLATED 20 BN6SF NF SLOTTED HEX NUT 2 BSC07 /6 x / COTTER PIN 22 GW /5500 LB DUST CAP 2 GF688 /8 NPT GREASE FITTING 5deg 2 GF6 /-28NF GREASE FITTING 25 GW5-5000LB BEARING KIT 26 GW50V 5000/5500 LB V-SEAL KIT 27 GW5V 5000/5500 LB BEARING WITH V-SEAL KIT Items 2-8 not sold as individual parts, only sold as complete repair kits shown 25, 26, & 27. FRONT LH AXLE ASSEMBLY RH AXLE ASSEMBLY Page

32 LB Hub & Spindle Assembly Page

33 000LB Hub & Spindle Assembly ITEM QTY PART NO. DESCRIPTION GW LB SPINDLE - 0 LG. 2 GW0VW 000 LB GRASS WRAP GW0VS 000 LB V-SEAL GW0VC 000 LB SEAL COUNTER FACE 5 GB LB INNER CONE 6 GB LB INNER CUP 7 GB LB OUTER CUP 8 GB LB OUTER CONE 9 BF6-9 HARD SAE FLAT WASHER GR.9 PLATED 0 BN6JS -NF SLOTTED JAM NUT BSC07 /6 x / COTTER PIN 2 GW2 000 LB DUST CAP 6 BW092 9/6-8 x / WHEEL BOLT GW0V 000 LB V-SEAL KIT 5 GWV 000LB BEARING WITH V-SEAL KIT 6 GW000B 000 LB HUB WITH BEARINGS, SEAL, & DUST CAP Complete assembly available as part number GW000A (includes hub, spindle, bearings, seals, dust cap, and hardware). Подбор запасных частей на сайте: Page

34 S-Tine and Shanks S-Tine Assembly SINGLE PC S-TINE ITEM QTY. PART NO. DESCRIPTION CT25D 2mm x 5mm HD HIGH CLEARANCE S-TINE 2 CT /2'' TINE CLAMP 2 x 5 TINE B080 /2 NC x HEX BOLT GR.5 PLATED BN08L /2 NYLOCK NUT NC 5 CT208G SUPER GOLD SHOVEL 6 CT2076B 2 / ULTRA BLUE 6MM GOOSEFOOT 7 B077 7/6NC x / LG. HEX BOLT GR. 5 8 BN07H 7/6 HEX NUT NC 9 B077CH 7/6 NC x / LG. COUNTER BOLT Items 7 & 8 are available together as part no. CT077 Items 8 & 9 are available together as part no. CT075H Torque 7/6 hardware to 75ft-lbs Подбор запасных частей на сайте: Page

35 S-Tine Installation for Tight Spots There are several locations on cultivators where this method of installation is required. Forward Step : Turn s-tine upside-down. Lower tine behind toolbar. Step 2: Rotate tine 90 Step Lower tip of tine Forward Tine shown with correct orientation Page 5

36 C-Shank Assembly and Parts 6 FOR x6 TUBE 2 FOR x6 TUBE FOR 2 /2 TUBE Подбор запасных частей на сайте: Page

37 C-Shank Assembly and Parts ITEM QTY PART NO. DESCRIPTION 2 BU06 U-BOLT 5/8 x 6 x 5 /2 2 2 BU062 U-BOLT 5/8 x 6 x /2 2 BU025 U-BOLT 5/8 x 2 /2 x BN0L 5/8 NYLOCK NUT NC 5 CT526 FORGED C-SHANK EDGE BENT LEAF / X / 6 BC020H 5/8NC x 2 LG. CARRIAGE BOLT 7 BN0S 5/8 NC STOVER LOCK NUT 8 BU067 /8 X / X / U-BOLT 9 2 BN06S /8-6NC STOVER LOCK NUT 0 CT507 7 SWEEP CT509 9 SWEEP 2 CT507 0 / SWEEP x 7.5 mm THICK 2 BP075 7/6NC x /2 PLOW BOLT 2 BN07H 7/6NC HEAVY HEX NUT Shank head assembly is preassembled at the factory. See shank head parts drawing for replacement parts for shank head.. Insert shank leaf 5 into shank head. Retain leaf with 5/8 x 2 carriage bolt 6 and 5/8 lock nut 7. Place /8 x / x / u-bolt 8 over leaf and tighten with /8 lock nuts Attach sweep ( 0,, or 2 ) to front of shank with 7/6 x /2 plow bolts and 7/6 heavy hex nuts.. Mount shanks on frame using proper u-bolts,(, 2, or ) and 5/8 lock nuts. See shank layout drawing for shank mounting locations cm cm 9 0 / 26 cm Подбор запасных частей на сайте: Page 7

38 C-Shank Head Assembly and Parts ! 8 7 2! Do not overtighten pivot bolt. Tighten pivot bolt until snug, then lock with jam nut 5. Подбор запасных частей на сайте: Page

39 C-Shank Head Assembly and Parts ITEM NO. QTY PART NUMBER DESCRIPTION C902 OUTER C-SHANK WELDMENT 2 C9022 INNER C-SHANK WELDMENT 2 A60059 OD-/ ID X 5/6 LONG BUSHING B265 /NC x 6 /2 LG. HEX BOLT GR. 5 5 BN2J / JAM NUT 6 BC050H 5/8NC x 5 LG. CARRIAGE BOLT GR. 5 7 BN0L 5/8 NYLOCK NUT NC 8 GSE082A /2 RESET SPRING 2 TOTAL COILS W/ PLUGS 9 B00TH 5/8 NC X LG. TAP BOLT GR. 5 PLATED 0 BN0J 5/8NC JAM NUT GR. 5 ZD0079 OD x /6 ID x 2 7/8 DOM Подбор запасных частей на сайте: Page 9

40 Layouts 2ft C-Shank Layout 9 Shanks on 7 Spacing ft C-SHANK CULTIVATOR 7 C-SHANK LAYOUT 9 SHANKS TOTAL Подбор запасных частей на сайте: Page

41 2ft C-Shank Harrow Layout (/2 Inch Tines) PARKING STAND MOUNT TINE R6 TINE R6 6'2 ROLLER MR806 6'2 ROLLER MR ft C-SHANK CULTIVATOR HARROW LAYOUT /2 tines with single roller HARROW TOOL Подбор запасных частей на сайте: Page

42 2ft S-Tine Layout 6 Tines on Spacing TUBE LENGTH ft S-TINE CULTIVATOR TINE LAYOUT 6 TINES TOTAL 65 TUBE LENGTH Подбор запасных частей на сайте: Page

43 2ft S-Tine Harrow Layout (/2 Inch Tines) HARROW TOOL PARKING STAND MOUNT TINES R6-2 TYP. BETWEEN ROLLERS TINES R6 6' 2 ROLLER 6' 2 ROLLER 50 2ft S-TINE CULTIVATOR HARROW LAYOUT /2 tines with single roller Подбор запасных частей на сайте: Page

44 7ft C-Shank Layout Shanks on 7 Spacing Page

45 7ft C-Shank Harrow Layout (/2 Inch Tines) HARROW TOOL PARKING STAND MOUNT TINES R6 TINES R6 TINES R6 TINES R6 ' ROLLER 5' ROLLER 5' ROLLER ' ROLLER Page 5

46 7ft S-Tine Layout 5 Tines on Spacing Page

47 7ft S-Tine Harrow Layout (/2 Inch Tines) HARROW TOOL PARKING STANT MOUNT TINES R6 TINES R6 TINES R6 TINES R6 ' ROLLER 5' ROLLER 5' ROLLER ' ROLLER 2 - TYP. BETWEEN ROLLERS AT HINGES - 2 TYP. BETWEEN OTHER ROLLERS Page 7

48 9ft C-Shank Layout Shanks on 7 Spacing / 6 / 6 / 25 / / / / 20 / / 8 / / / / 2 / / 2 / / / 5 / 5 / 25 / / / / 20 / / 6 / 6 / Page

49 9ft C-Shank Harrow Layout (/2 Inch Tines) INSTALL HARROW TOOL HERE PARKING STAND MOUNT / TINE R6 6 /2 28 TINE R TINE R6 6 /2 ' ROLLER 5' ROLLER 6' ROLLER ' ROLLER 50-9' C-SHANK HARROW LAYOUT /2 TINES + SINGLE ROLLER / TINE R Page 9

50 9ft S-Tine Layout 58 Tines on Spacing 9 / 7 / / 9 / 6 / 6 / / / / / /2 / 2 / / / 2 / 6 / /2 / / 2 / / 2 / / / 2 / / 5 / 6 / / 6 5 / / / 25 / /2 / Page

51 9ft S-Tine Harrow Layout (/2 Inch Tines) Harrow tool Parking stand mount / 25 /2 0 / /2 25 /2 / TINES R6 ' ROLLER TINES R6 TINES R6 TINES R6 5' ROLLER 6'2 ROLLER ' ROLLER Page 5

52 2ft C-Shank Layout 7 Shanks on 7 Spacing 2 / 5 / / 6 / 6 / 25 / / / / 20 / / 8 / / / / 2 / / 2 / / / 5 / 5 / 25 / / / / 20 / / 6 / 6 / 2 / 5 / Page

53 2ft C-Shank Harrow Layout (/2 Inch Tines) INSTALL HARROW TOOL HERE PARKING STAND MOUNT 9 / TINE R6 6 /2 28 TINE R TINE R6 6 /2 6' ROLLER 5' ROLLER 5' ROLLER 6' ROLLER 9 / TINE R Page 5

54 2ft S-Tine Layout 6 Tines on Spacing 8 / 9 / 7 / / 9 / 8 / 6 / 6 / / / / / / / /2 / 9 / 9 / 2 / / / 2 / 6 / /2 / / / / 2 / / 2 / / / 2 / / 5 / 6 / / 6 5 / / / 25 / /2 9 / Page

55 2ft S-Tine Harrow Layout (/2 Inch Tines) Harrow tool Parking stand mount 9 / 25 /2 0 / /2 25 /2 9 / TINES R6 TINES R6 TINES R6 TINES R6 6'2 ROLLER 5' ROLLER 5' ROLLER 6'2 ROLLER Page 55

56 2ft C-Shank Layout 9 Shanks on 7 Spacing 20 / 6 / 6 / / 8 / / / / 25 / / / / 8 / 6 / / / 2 / 2 / / / / / 5 / 5 / / / / 6 / / 20 / 6 / 6 / 8 / / Page

57 2ft C-Shank Harrow Layout (/2 Inch Tines) INSTALL HARROW TOOL HERE PARKING STAND MOUNT TINE R6 2 TINE R6 0 2 TINE R6 2 5 TINE R6 6'2 ROLLER 5' ROLLER 6'2 ROLLER 6'2 ROLLER Page 57

58 2ft S-Tine Layout 68 Tines on Spacing Page

59 2ft S-Tine Harrow Layout (/2 Inch Tines) Harrow tool Parking stand mount / 29 /2 0 / /2 29 /2 50 / TINES TINES R6 R6 6'2 ROLLER 5' ROLLER TINES R6 6'2 ROLLER TINES R6 6'2 ROLLER Page 59

60 5 / 25ft C-Shank Layout Shanks on 7 Spacing 5 / / 20 / 6 / 6 / / 8 / / / / 25 / / / / 8 / 6 / / / 2 / 2 / / / / / 5 / 5 / / / / 6 / 20 / / 6 / 6 / 8 / / / Page

61 25ft C-Shank Harrow Layout (/2 Inch Tines) INSTALL HARROW TOOL HERE PARKING STAND MOUNT TINE R65 TINE R6 TINE R6 5 TINE R65 6'2 ROLLER 6'2 ROLLER 6'2 ROLLER 6'2 ROLLER Page 6

62 ft S-Tine Layout 76 Tines on Spacing Page

63 25ft S-Tine Harrow Layout (/2 Inch Tines) Harrow tool Parking stand mount / / TINES R6 TINES R6 TINES R6 6'2 ROLLER TINES R6 6'2 ROLLER 6'2 ROLLER 6'2 ROLLER Page 6

64 SEE HARROW LAYOUT FOR HARROW TOOL LOCATION 0 MOUNT EXTENSION WITH BOLT PLATE ON BOTTOM, AND GUSSETS TO THE FRAME REFER TO TINE LAYOUT FOR TUBES AND LENGTHS 7 8 Harrow Parts S-Tine Harrow Installation Page

65 S-Tine Harrow Installation ITEM PART NO. DESCRIPTION R /550 REAR BAR MOUNT 2 RB09 62 HARROW ARM ASSEMBLY BU020 5/8 x 2 x /2 U-BOLT BU0825 /2 x 2 /2 x /2 U-BOLT 5 BN08L /2 NYLOCK NUT NC 6 BU025 U-BOLT 5/8 x 2 /2 x 7 BN0L 5/8 NYLOCK NUT NC 8 BU06 U-BOLT 5/8 x 6 /6 x 5 /2 9 B020 5/8NC x 2 HEX BOLT 0 RB0025 TOOL,HARROW TIGHTENER RB0026 HOLDER,HARROW TOOL 2 BF0HS 5/8 HARD STRUCTURAL FLAT WASHER Hole settings for harrow heads to extensions Single piece s-tine 2 piece s-tine Double roller and level bar harrows Double roller and level bar harrows /2 tine combination harrows /2 tine combination harrows Use this hole for L-Pin to set tine height Page 65

66 C-Shank Harrow Installation /6 6 TOP / See harrow layout for harrow tool holder location 9 0 Page

67 C-Shank Harrow Installation ITEM NO. PART NUMBER DESCRIPTION RB09 62 HARROW ARM ASSEMBLY - 5/8 PIVOT 2 BU06 U-BOLT 5/8 x 6 x 5 /2 BN0L 5/8 NYLOCK NUT NC BU0825 /2 x 2 /2 x /2 U-BOLT 5 BN08L /2 NYLOCK NUT NC 6 BU020 5/8 x 2 x /2 U-BOLT 7 R800 0 EXTENSION 8 B020 5/8 X 2 BOLT GR. 5 PLATED 9 RB0025 TOOL,HARROW TIGHTENER 0 RB0026 HOLDER,HARROW TOOL Mount harrow tool holder between plate and nut on leftmost head on the main frame (see layout for location). Harrow tool sits in holder. Leave - between rollers on wings and rollers on main frame, and leave -2 between all other rollers. Hole settings for harrow heads to extensions Double roller and level bar harrows /2 tine combination harrows Use this hole for L-Pin to set tine height Page 67

68 ROLLER ARM STOP BRACKET INSTALL LOCATION S-Tine RTS (not including 6ft) 6ft RTS and Other Machines 2 S-Tine RTS and Other Machines SEE INSTALL LOCATION STANDARD POSITION AS SHOWN FLIP SPACER OVER FOR S-TINES 8 62 Harrow Arm Assembly Page

69 62 Harrow Arm Assembly ITEM NO. QTY. PART NO. DESCRIPTION R002 PARALLEL LINKAGE BAR 2 R0006 PARALLEL LINKAGE ARM R80099 HEAD,SALFORD HARROW FOR 5/8 UPPER PIVOT BOLT R HARROW ARM FOR 5/8 PIVOT AND U-BOLTS 5 R8000A 62 HARROW ARM W/ KIT (REPLACES RB25) 6 5 BC085H /2 X NC X -/2 LG. CARRIAGE BOLT GR. 5 SHORT THREAD 7 R000 NYLON BUSHING / OD x /2 ID x.9 LG. 8 7 BN08L /2 NYLOCK NUT NC 9 2 BN0L 5/8 NYLOCK NUT NC 0 GP08002L0 /2 x /2 L - PIN GHP # HAIR PIN 2 2 R005 2 x 0 HARROW ARM SPRING R8028 ROLLER ARM STOP BRACKET (LONG) R8007L TINE SECTION UPRIGHT PLATE LEFT 5 R8007R TINE SECTION UPRIGHT PLATE RIGHT 6 R0028 STEEL HEAD SPACER 2 /8 LG. 7 2 B07ST 5/8 - NC X / SHORT THREAD BOLT 8 R /8OD NYLATRON BUSHING 9 R8006 7/8OD ID NYLATRON ROD 20 R80096 HARROW ARM SPACER 2 2 RB002 TIGHTENER,SINGLE SPRING 22 2 B065 /8 X /2 LG. GRADE BN06L /8-6NC LOCK NUT 2 2 GHP9 #9 HAIR PIN 25 B05 5/8 x /2 HEX BOLT GR 5 Подбор запасных частей на сайте: Page 69

70 Tine Harrow Assembly FOR FRONT TUBE ONLY TINE ANGLE ADJUSTER SHOWN HERE ON INNER LEFT. SEE HARROW LAYOUT FOR MACHINE SPECIFIC POSITIONS. FOR ADJUSTOR MOUNTS ONLY ALL OTHER POSITIONS FRONT Page

71 Tine Harrow Assembly /2 - TINE HARROW ASSEMBLY PART NO. R6 ITEM NO. PART NO. DESCRIPTION U TUBE 2 /2 x 2 /2 x /6W x 5 LG. 2 R606 TINE PIPE FOR /2 (-TINE) /2 - TINE HARROW ASSEMBLY PART NO. R6 ITEM NO. PART NO. DESCRIPTION U TUBE 2 /2 x 2 /2 x /6W x 72 LG. 2 R606 TINE PIPE FOR /2 (-TINE) /2-5 TINE HARROW ASSEMBLY PART NO. R65 ITEM NO. PART NO. DESCRIPTION U TUBE 2 /2 x 2 /2 x /6W x 92 LG. 2 R6065 TINE PIPE FOR /2 (5-TINE) /2-6 TINE HARROW ASSEMBLY PART NO. R66 ITEM NO. PART NO. DESCRIPTION U TUBE 2 /2 x 2 /2 x /6W x 2 LG. 2 R6066 TINE PIPE FOR /2 (6-TINE) 22 R8025 VINYL HANDLE FOR TINE ADJUSTMENT COMMON PARTS ITEM NO. PART NO. DESCRIPTION R0002 /2 TINE TUBE CONNECTOR R00 CLAMP BRACKET 5 B082 /2 X / BOLT 6 BN08L /2 NYLOCK NUT NC 7 BU025 U-BOLT 5/8 x 2 /2 x 8 BN0L 5/8 NYLOCK NUT NC 9 R60000 /2 WIRE - 20 DBL LEG SPRING TINE 0 R0007 ADJUSTING BRACKET WELDMENT R0005 /2 TINE BAR ADJUST CONNECTOR 2 R000 ADJUSTING BAR HD BAR TINE R0008 ADJUSTING BRACKET HANDLE WELDMENT R OD x.8 ID X 7/8 LONG SPACER 5 B060 /8NC x LG. HEX BOLT 6 BN06S /8-6NC STOVER LOCK NUT 7 B065 /8NC x /2 LG. HEX BOLT 8 R005 LIGHT SAVER BRACKET 9 B060 /8NC x HEX BOLT 20 B085 /2 x /2 HEX BOLT 2 GHP # HAIR PIN 22 R8025 VINYL HANDLE FOR TINE ADJUSTMENT Page 7

72 0 Roller Assembly 7 2 FRONT SALFORD Decal on frame tube facing rear PT#GD07 Install grease decal towards rear of frame PT# GD080 6 RH SPIRAL (' ROLLER SHOWN) 8 Install bearing with grease fitting facing up and towards rear of roller Подбор запасных частей на сайте: NOTE: Grease fitting is included in bearing kit when ordering a new bearing. Page

73 0 Roller Assembly 0 ROLLER HARROW ASSEMBLY - ' 0 (9.cm) LONG COMPLETE ASSEMBLY PART NO. MRB0(R/L) ITEM QTY PART NO. DESCRIPTION RB05 ' ROLLER FRAME FOR 0'' ROLLER 2 RB02 ' ROLLER ONLY RH SPIRAL, 0'' DIA 0 ROLLER HARROW ASSEMBLY - ' 0 (2.9cm) LONG COMPLETE ASSEMBLY PART NO. MRB0(R/L) ITEM QTY PART NO. DESCRIPTION RB05 ' ROLLER FRAME FOR 0'' ROLLER 2 RB02 ' ROLLER ONLY RH SPIRAL, 0'' DIA 0 ROLLER HARROW ASSEMBLY - ' 6 (7.2cm) LONG COMPLETE ASSEMBLY PART NO. MRB6(R/L) ITEM QTY PART NO. DESCRIPTION RB65 '6 ROLLER FRAME FOR 0'' ROLLER 2 RB62 '6 ROLLER ONLY RH SPIRAL, 0'' DIA 0 ROLLER HARROW ASSEMBLY - 5' 0 (52.cm) LONG COMPLETE ASSEMBLY PART NO. MRB50(R/L) ITEM QTY PART NO. DESCRIPTION RB505 5' ROLLER FRAME FOR 0'' ROLLER 2 RB502 5' ROLLER ONLY RH SPIRAL, 0'' DIA 0 ROLLER HARROW ASSEMBLY - 6' 2 (88cm) LONG COMPLETE ASSEMBLY PART NO. MRB62(R/L) ITEM QTY PART NO. DESCRIPTION RB625 6'2 ROLLER FRAME FOR 0'' ROLLER 2 RB622 6'2 ROLLER ONLY RH SPIRAL, 0'' DIA 0 ROLLER HARROW ASSEMBLY - 6' 8 (20.2cm) LONG COMPLETE ASSEMBLY PART NO. MRB68(R/L) ITEM QTY PART NO. DESCRIPTION RB685 6'8 ROLLER FRAME FOR 0'' ROLLER 2 RB682 6'8 ROLLER ONLY RH SPIRAL, 0'' DIA COMMON PARTS ITEM QTY PART NO. DESCRIPTION R000R TRIPLE SEAL BEARING RIGHT HAND R000L TRIPLE SEAL BEARING LEFT HAND 5 2 GF6 /-28NF GREASE FITTING 6 B085FS /2 NC X /2 FLAT SOCKET HEX CAP 7 BN08L /2 NYLOCK NUT NC 8 2 BR00-00 '' RETAINING SNAP RING Page 7

74 5 2 6 Install bearing with grease fitting facing rear of roller RH SPIRAL (5' ROLLER SHOWN) 0HR Install grease decal towards rear of frame PT# GD07 SALFORD Decal on frame tube facing rear PT# GD25 FRONT/BACK Decal PT# GD080 Arrow shows roller rotation direction 7 Roller Assembly Подбор запасных частей на сайте: Page

75 Roller Assembly ROLLER HARROW ASSEMBLY - ' 0 (9.) LONG COMPLETE ASSEMBLY PART NO. MR80(L/R) ITEM NO. QTY. PART NO. DESCRIPTION R807R ' ROLLER ONLY RIGHT HAND SPIRAL, DIA. 2 R807- ' ROLLER FRAME FOR ROLLER 2 A60099 / x /2 x 9/2LG BUSHING 2 GB9-B /2 BEARING COMPLETE 5 2 BN20JL /NC JAM LOCK NUT 6 6 BC082H CARRIAGE BOLT /2NC x / LG. GR BN08S /2-NC STOVER LOCK NUT ROLLER HARROW ASSEMBLY - ' 0 (2.9) LONG COMPLETE ASSEMBLY PART NO. MR80(L/R) ITEM NO. QTY. PART NO. DESCRIPTION R808R ' ROLLER ONLY RIGHT HAND SPIRAL, DIA. 2 R807- ' ROLLER FRAME FOR ROLLER 2 A60099 / x /2 x 9/2LG BUSHING 2 GB9-B /2 BEARING COMPLETE 5 2 BN20JL /NC JAM LOCK NUT 6 6 BC082H CARRIAGE BOLT /2NC x / LG. GR BN08S /2-NC STOVER LOCK NUT ROLLER HARROW ASSEMBLY - 5' 0 (52.) LONG COMPLETE ASSEMBLY PART NO. MR805(L/R) ITEM NO. QTY. PART NO. DESCRIPTION R809R 5' ROLLER ONLY RIGHT HAND SPIRAL, DIA. 2 R ' ROLLER FRAME FOR ROLLER 2 A60099 / x /2 x 9/2LG BUSHING 2 GB9-B /2 BEARING COMPLETE 5 2 BN20JL /NC JAM LOCK NUT 6 6 BC082H CARRIAGE BOLT /2NC x / LG. GR BN08S /2-NC STOVER LOCK NUT ROLLER HARROW ASSEMBLY - 6' 2 (87.9) LONG COMPLETE ASSEMBLY PART NO. MR806(L/R) ITEM NO. QTY. PART NO. DESCRIPTION R8050R 6'2 ROLLER ONLY RIGHT HAND SPIRAL, DIA. 2 R '2 ROLLER FRAME FOR ROLLER 2 A60099 / x /2 x 9/2LG BUSHING 2 GB9-B /2 BEARING COMPLETE 5 2 BN20JL /NC JAM LOCK NUT 6 6 BC082H CARRIAGE BOLT /2NC x / LG. GR BN08S /2-NC STOVER LOCK NUT Page 75

76 Lights & Hydraulics 2 Axle Lift Hydraulics J B G H E E D J A 2 A G 6R 5 # HARDWARE # HOSE F 5 C K 6R (RED-GREY) (RED) A D B 2 A A B B 5 5 ROUTE HOSES ALONG FRAME AND CLAMP WHERE PROVIDED E FACE PORTS AWAY FROM THE REAR TIRE Page

77 2 Axle Lift Hydraulics HARDWARE ITEM NO. QTY PART NO. DESCRIPTION A 2 HSR5095 /2 BORE x 9 /2 STROKE REPHASING CYLDINER B 2 HSR208 /2 BORE x 8 STROKE REPHASING CYLINDER C 2 H800P /2 NPT MALE PIONEER COUPLER D HPMSC0 STROKE CONTROL VALVE E 8 H ORB TO -06 NPT SWIVEL ELBOW F H ORB PLUG G 2 H NPT ALL SWIVEL TEE H H TO -08 NPT MALE UNION J 2 H ORB TO -08 NPT SWIVEL ELBOE K HG-PT22E22R2R PAIR OF RED/RED GREY HOSE GRIPS HOSE LABEL QTY ENDS (ALL NPT) HOSE SIZE LENGTH FROM TO A (RED) /2 - /2 /2 2' TRACTOR S.C. VALVE B /2 - /2 /2 ' S.C. VALVE TEE AT LEFT HSR /2 - /8 /8 '6 TEE AT LEFT HSR509 RIGHT HSR5095 BARREL 2 /8 - /8 /8 2'8 HSR5095 ROD HSR508 BARREL 5 2 /8 - /2 /8 '9 HSR508 ROD RETURN TEE 6R (RED) /2 - /2 /2 8'6 RETURN TEE TRACTOR CHARGING THE CIRCUIT ATTENTION ON HARD GROUND, DO NOT RETRACT CYLINDERS ALL THE WAY WHILE THE TONGUE IS HITCHED TO TRACTOR - OR UNHOOK THE TURNBUCKLE FROM THE TONGUE TELESCOPE. OTHERWISE, THE TRACTOR DRAWBAR CAN BE BENT UPWARDS. Connect only the Barrel end of the cylinders until the circuit has been charged.. Be sure that all cylinders can extend completely without striking anything. Prop with blocks if necessary. 2. Connect Tractor.. Extend cylinders and hold lever for 2- minutes. This will purge the air from the circuit. (The lift cylinders have a port that allows oil to pass when completely extended.). The circuit is now free from air. Install Rod end Pins. Connect tongue Turnbuckle ****Whenever air could have entered the cylinders, repeat**** above steps to purge circuit Identify the lift hose ends with red tie wraps for quick hookup to tractor. Route hoses behind axle towers Leave a small droop of hose (-) across wing joint Page 77

78 F 2 K F E A L D D F B H H Clamp hoses to frame and telscope at bolts P M N J 6 A G F Route hoses along telescope and tripod 5 G 5 A A 5 5 C B B C F Axle Lift Hydraulics Page

79 7-25 Axle Lift Hydraulics HARDWARE ITEM QTY PART NO. DESCRIPTION A 2 HSR5095 /2 BORE x 9 /2 STROKE REPHASING HYD. CYLINDER B 2 HSR508 /2 BORE x 8 STROKE REPHASING HYD. CYLINDER C 2 HSR208 / BORE x 8 STROKE REPHASING HYD. CYLINDER D 2 H800P /2M NPT PIONEER TIP E HPMSC0 STROKE CONTROL VALVE F 2 H ORB TO -06 NPT SWIVEL ELBOW G 2 H /2 NPT ALL SWIVEL TEE H HG-PT22E22R2R RED & RED/GREY HOSE GRIPS (WITH /2 NPT MALE-FEMALE) J H90086 /2 TO /8 NPT MALE UNION K H ORB PLUG L 2 H ORB TO /2F NPT SWIVEL ELBOW M 7 P060A HOSE CLAMP - N 5 P060B HOSE CLAMP - P 2 BN06L /8 NYLOCK NUT HOSE LABEL QTY ENDS (ALL NPT) HOSE SIZE LENGTH 7' 9'-25' FROM A /2 - /2 /2 2' TRACTOR S.C. VALVE B /2 - /2 /2 ' S.C. VALVE RIGHT HSR5095 BASE 2 /2 - /8 /8 ' 6 RIGHT HSR5095 BASE LEFT HSR5095 BASE 2 /8 - /8 /8 2' 8 HSR5095 ROD HSR508 BASE 2 /8 - /8 /8 8' 0' HSR508 ROD HSR208 BASE 5 2 /8 - /2 /8 7' 8 9' 6 HSR208 ROD RETURN TEE 6 /2 - /2 /2 8' 6 RETURN TEE TRACTOR TO IMPORTANT CHARGING THE CIRCUIT On a concrete pad or hard ground, do not retract cylinders all the way while tongue is hitched to tractor, this could result in bending the tractor drawbar upwards. **Connect only the pins on the barrel ends of the cylinders until the circuit has been charged.** 2. Prop cylinders with blocks of wood, be sure that all cylinders can extend completely without striking anything.. Connect hoses to tractor.. Extend cylinders and hold lever for 2- minutes. This will purge the air from the circuit. (The lift cylinders have a port that allows oil to pass when completely extended.) 5. The circuit is now free from air. Install Rod end Pins. Connect tongue telescope. Whenever air could have entered the cylinders, repeat above steps to purge circuit. Test wing fold and adjust hose droop at wings if necessary. Identify the lift hose ends with red tie wraps for quick hookup to tractor. Route hoses behind tower Leave a droop in hose at wing hinge Page 79

80 7-25 Wing Fold Hydraulics A H 7R 8B E RESTRICTOR GREEN GREY Return GREEN Feed ROUTE HOSES ALONG FRAME. CLAMP WHERE PROVIDED. B RESTRICTORS ON (TEE) RETURN TEE (ROD) E B E 0 C C F/G 9 F/G B D C Подбор запасных частей на сайте: Page

81 7-25 Wing Fold Hydraulics * ** ITEM QTY PART NO. DESCRIPTION A 2 H800P COUPLER /2 NPT MALE PIONEER B 2 H TEE FEMALE SWIVEL NPT C H95586 / ORB - /8 FEMALE SWIVEL NPT ELBOW D H95086 / ORB TO /8 NPT STRAIGHT CONNECTOR E 2 H RESTRICTOR /8M NPT TO /8F NPT F 2 HS02 BORE x 2 STROKE HYDRAULIC CYLINDER G 2 HS52.5 BORE x 2 STROKE HYDRAULIC CYLINDER H HG-PT2E2R2R PAIR OF GREEN/GREEN GREY HOSE GRIPS * Used on 7' 50 cultivators before S/N Used on all 9'-25' 50 cultivators. **Used on 7' 50 cultivators after S/N LABEL QTY ENDS HOSE LENGTH FROM TO (ALL NPT) SIZE 7R /2 - /8 /8 27'6 TRACTOR TEE 8B /2 - /8 /8 29' TRACTOR TEE ON RIGHT CYLINDER BARREL 9 /8 - /8 /8 '6 TEE ON RIGHT BARREL OF LEFT CYLINDER HS02 BARREL 0 /8 - /8 /8 '6 RESTRICTOR ON TEE ROD OF LEFT CYLINDER /8 - /8 /8 5'2 RESTRICTOR ON TEE ROD OF RIGHT CYLINDER Do not connect the cylinder rod until system has been charged with oil.. Prop up the cylinder with a block of wood (fig ). Check to see that the rod will extend completely without striking anything. 2. Connect tractor (note: check to see that all cylinders extend and retract in sync. If one goes backwards, check the plumbing.). Extend cylinders completely, hold lever for 0 sec. as air exits cylinder.. Retract cylinder completely, hold lever for 0 sec. as air exits. 5. Repeat steps & three times. 6. Install cylinder pins. Be sure washers are installed correctly (see fold cylinder parts page). Air in the wing cylinder will cause wings to fall to the ground!!! Whenever air could have entered the cylinders, repeat the process above to purge circuit. ALWAYS UNFOLD WINGS before working on hydraulics!!! Never work on a lift system with the wings folded Identify the fold hose ends with green hose grips for quick hookup to tractor. When charging the circuit, prop up cylinder with block of wood. Be sure the rod can extend freely without striking anything Page 8

82 Lights, SMV & Parking Stand Install Standard Parking Stand Shown Note: S-Tine and C-Shank machines have a different harrow set-up. Refer to S-Tine Harrow Installation or C-Shank Harrow Installation pages for harrow set-up IMPORTANT: HAVE SOMEONE WATCH FOR COLLISIONS WHEN FOLDING FOR THE FIRST TIME Page

83 * * ** Lights, SMV & Parking Stand Install ITEM QTY PART NO. DESCRIPTION L00 OFFSET SMV MOUNTING BRACKET 2 GAP0NS SMV SIGN 2 B060 /8 X LG. GRADE 5 2 BN06L /8-6NC LOCK NUT 5 6 B020 5/8NC x 2 HEX BOLT 6 6 BN0L 5/8 NYLOCK NUT NC 7 2 A60055 LIGHT BRACKET (SHORT) 8 2 L0025 OUTSIDE LIGHT MOUNTING PLATE 9 BU00 / x x /2 U-BOLT 0 8 B02 / NC x /2 HEX BOLT 6 BN0L / LOCK NUT 2 2 GL AA ORANGE LIGHT 2 GL R RED LIGHT GL SALFORD WESBAR LIGHT KIT 5 C5509 Standard Parking Stand Set for mounting on 6 beam * Included in GL (lights and wires) ** Optional Parking Stand with 5000LB Jack (kit KCRP5000) replaces C5509 SMV Hole Use Light Bracket Hole Use All 50 S-Tine Machines 25' C-Shank 9' C-Shank Page 8

84 Lights, SMV & Parking Stand Install Standard Parking Stand C5509 ITEM QTY PART NO. DESCRIPTION C5507 REAR PARKING STAND MOUNT FOR 6 BEAM 2 C PARKING STAND 2 BU06 U-BOLT 5/8 x 6 x 5 /2 BN0L 5/8 NYLOCK NUT NC 5 GP00C0 5/8'' DIA x /'' PIN RING & WASHER 6 GHP # HAIR PIN Подбор запасных частей на сайте: Page

85 Lights, SMV & Parking Stand Install Optional Parking Stand with 5000LB Jack KCRP5000 ITEM QTY PART NO. DESCRIPTION A607 REAR JACK STAND MOUNT 2 A606 REAR JACK STAND ARM A608 REAR JACK STAND GJ5000S 5000 LB TONGUE JACK 5 2 BU050 5/8 x 5 x /2 U-BOLT 6 2 BU260 / x 6 x 6 U-BOLT 7 BN0L 5/8 NYLOCK NUT NC 8 BN2S / STOVER LOCK NUT 9 2 GP00C0 5/8'' DIA x /'' PIN RING & WASHER 0 2 GHP # HAIR PIN Mount Parking Stand on tube between tines and roller. be sure no parts collide with parking stand assembly during operation ATTENTION: Always operate machine with parking stand tube in raised position otherwise crank handle on jack may contact roller Page 85

86 Decals Decal Locations FRONT VEIW OF TRIPOD ITEM 50 2' QTY 50 7'-25' QTY PART NO. DESCRIPTION 6 0 GD00 SALFORD DECAL LRG. w/black BORDER(''HIGH X 6'' LONG) GD02 WWW. SALFORD DECAL 2 2 GD50 MODEL 50 DECAL GD09 DEPTH CONTROL DECAL 5 GD2 ATTENTION LUBRICATE DECAL 6 - GD0 WARNING: DO NOT LIFT WINGS UNTIL HYDRAULIC CYLINDERS AND LINES ARE FULL OF OIL AND FREE OF AIR 7 2 GD9 CAUTION - L X 5 TIRE DECAL GDSW2 USE PROPER TOOLS AND READ MANUAL DECAL GDT DANGER STICKER FOR CRUSHING HAZARD GD080 GREASE EVERY 0 HOURS DECAL GDSW SAFE OPERATION LIST DECAL 2 GDSW700 WARNING STICKER, ALTERNATE HIGH PRESSURE FLUID HAZARD GD20 HOSE IDENTIFICATION DECAL - 2 GD 570 WING LOCK 5 - GDSW200 WARNING: OVERHEAD WING HAZARD Page

87 Decal List GD00 GD02 2 GD50 GD09 GD2 5 GD0 6 GD9 7 GDSW2 8 GDT 9 GD080 0 GDSW GDSW700 2 GD20 GD GDSW Page 87

88 Tow Hitch Optional Tow Hitch Installation ITEM QTY PART NO. DESCRIPTION C NARROW TOW HITCH 2 C0859 TOW HITCH INSERT C092 DROP TOW HITCH INSERT 2 BU26 U-BOLT / x x 7 /2 LG. 5 BN2L / NC NYLOCK NUT 6 2 BU06 U-BOLT 5/8 x x 7 /2 LG. 7 5 BN0L 5/8 NYLOCK NUT NC 8 GPSPEC6C000 RING & WASHER TOW HITCH SPRING PIN 9 C072 TOW HITCH PIN SPRING 0 GM26 MACHINE BUSHING BSR05 / X /2 ROLL PIN 2 T0028 TOW HITCH CLEVIS GP200062B06 / x 6 /2 LG. PIN - HOLE B0625 /8 NC x 2 /2 LG. HEX BOLT GR. 5 5 B020 5/8 X 2 BOLT GR. 5 PLATED 6 BN06L /8-6NC LOCK NUT 7 GF60 /8 NPT GREASE FITTING RE-LOCATE PARKING STAND TO THE SIDE OF TOW HITCH IF NECESSARY OPTIONAL DROP TOW HITCH INSERT USED FOR TOWING ANHYDROUS TANKS Page

89 Notes Подбор запасных частей на сайте: Page 89

90 Подбор запасных частей на сайте: