SAFETY. Hitchpole, centre frame 1. Centre frame wheels & roller 3. Centre & wing frames 5. Wing frame wheels & roller 9.

Transcription

1 MANUAL

2 Hitchpole, centre frame 1 Centre frame wheels & roller 3 Centre & wing frames Wing frame wheels & roller 9 Hydraulics 11 Clearance lights 13 Operations 1 Safety, warranty 1 SAFETY Industrial Drive, Box 830 Regina, Sask. Canada SP 3B1 Toll Free: fx degelman@degelman.com The safety instructions that follow pertain only to this specific equipment. You should be aware of agricultural & industrial safety especially related to heavy equipment. If you are not familiar with safety procedures then you should get training. Improper use will result in maiming or death.

3 Hitch pole & centre frame p1

4 Transport Floatation plate USE TRANSPORT PIN Field 1 1 / Grease point Every hrs Grease fitting Store transport pin Centre frame Hitch pole Pole pin Bolt /8 x 3-1/ 118 Lock nut /8 UNITQ Rachet jack Jack handle Hair pin Pin 1 x -1/8 EFF 3 Floatation plate Bent pin Lynch pin Bolt 1-1/ x c/w ftg Lock nut 1-1/ Sidewind jack Manual holder Bolt 1/ x Flat washer 1/ Lock nut 1/ p

5 Centre frame, wheels & roller Store hyd cyl transport lock Grease point Every hrs 11 p3 13

6 The wing rollers use the same bearing system Centre roller Bearing Lock ring 116 Bearing insert 11 Flange casting Bushing Bolt /8 x Lock washer / Nut /8 8 8 Rockshaft Cast bearing cap Cast bearing base Bolt 3/ x 1/ Shim Flat washer 3/ Lock nut 3/ Hub & spindle Cotter pin Dust cap - CTD Slotted nut 1 UNS Flat washer 1 SAE Cone bearing Bearing cup Hub H618G - CTD Bearing cup Cone bearing Dust seal Spindle Bolt 1/ x 3 1/ Lock nut 1/ UNITQ 1 Per wheel Wheel Whl bolt 9/16 x 1 3/ Tire 9.Lx1 6ply Valve TR Rim 1 x 8 6 bolt Jam nut 9/16 UNF p

7 Centre & wing frames 1 Hydraulic cylinder 31/x16x11/ Centre frame 8 Truss arm 1 Wing frame p

8 LH wing frame RH 1 3 LH auto fold latch 1 36 RH Bolt 1/ x 3 1/ 31 Autofold collar 1180 Lock nut 1/ UNITQ Bolt 1/ x 1/ 1303 Comp. spring Flat washer 1/ Lock nut 1/ UNITQ Cable Cotter pin Flat Washer M18 SAE Cable pin Eyebolt /8 x 1/ Flat washer /8 SAE Lock nut /8 UNITQ Bushing 1-1/ x 3/ 1 3 LH autofold arm RH 1 3 Bolt 1/ x 3 1/ Autofold collar Lock nut 1/ UNITQ Swing arm holder Bolt /8 x Flat washer / Lock washer / Nut / Grand total p6

9 Centre & wing frames p

10 Cross joint 33 Cross joint pin Bolt /8 x 118 Lock nut /8 UNITQ Truss arm Bolt 1x1/ 118 Lock washer Nut Hose holder Bolt /8 x Flat washer / Lock washer Nut / Safety chain 1 8 p8

11 Wing frame, wheels & roller Install roller as with centre frame Wheel Whlbolt9/16x13/ Tire 9.Lx1 6ply Valve TR Rim 1x8 6 bolt Jam nut 9/16 UNF Wing roller 311 LH end wheel strut 1 3 RH Bolt 1 1/ x c/w ftg 118 Lock nut 1 1/ 6 31 Upper link plate 306 Link bar Bolt 1 1/ x c/w ftg 6 Lock nut 1 1/ Bushing 1 1/ x Bushing 1 1/ x 3/ 1 Grand total Hub & bent spindle Cotter pin Dust cap - CTD Slotted nut 1 UNS Flat washer 1 SAE Cone bearing 1 13 Bearing cup Hub H618G - CTD Bearing cup 1 13 Cone bearing Dust seal Bent spindle Hitch pin Lynch pin 1 Per wheel p9

12 Hydraulic cylinder 31/x16x11/ Store hyd cyl transport lock 18 1 Grease point Every 0 hrs Grease fitting p

13 Grease point Every hrs Hydraulics / x 16 x 1 1/ Cylinder four per machine Barrel Lock ring Open cap 1 1 USE TRANSPORT LOCK 1099 Rod & clevis Piston Lock nut /8 UNF UNITQ Clevis pin Lock washer 1/ Bolt 1/ x Seal kit 3 1/ x 1 1/ Transport lock Wire lock pin Hose clamp Top plate Bolt /16 x 1 1/ p11 Store transport lock

14 () () 116 Coupling 1/ NPT (male tip) 111 Nipple (M) 1/ NPT x 3/ JIC 11 Tee 3/ JIC M 1 Tee 3/ M JIC x JIC x ORB 1 Elbow 3/ M JIC x ORB () (Hose length in inches) 160 Hose 3/8 x () (0) Hose 3/8 x () 169 Hose 3/8 x (0) 1663 Hose 3/8 x (96) Ports face up (96) Ports face up (96) p1

15 Clearance lights 11& Pole plug / SuperVU line 8ft Junction box Straight cord conn Plastic locknut 1/ NPT Terminal strip conn Screw #8, 3/ Screw 1/ self-tap Rubber washer 3/16ID LH Dual lamp RH Lamp/SMV brkt, left side Bolt 1/ x 1 1/ Lock nut 1/ /3 SuperVu line 0ft 11 0 Loom Clamp 3/8 cushion 13 0 Grommet 3/ Grommet 1/ Loom Butt splice crimp 16ga Triplug SMV sign Bolt 1/ x Lock washer 1/ 1180 Nut 1/ Bolt 1/ x 1-1/ 1180 Lock washer 1/ Nut 1/ 9 3 Lamp brkt, right side Make sure blank faces forward colours face back 3 0 Orange 18 1 Red Left side Right side p13

16 Y brown G G W B R RH turn Ground Tail LH turn G W G W Right wire B B Left wire Splice R W brown Amber light Ground Red light 1 POLE PLUG 16/ WIRE JUNCTION BOX 16/3 WIRE TRIPLUG Cut loom for Triplug p1

17 Transport Latch open A PREPARE Take off transport locks Cable taut Set floatation plate to field position Latch closed D SET LATCH CLOSED Drop drums with wings almost out Back up until wings all the way out then wing arm clicks in Cable slack p1

18 C BRING WINGS OUT Back up slowly B ANGLE OUT TRANSPORT WHEEL Drop roller Turn axle Lift roller Field AUTOFOLD LATCH ADJUSTMENT: After a while the cable will stretch and the latch won t open to free the Swing Arm. To adjust, have the wings out. With the swing arm pipe in the latch and the latch open just enough for the swing arm to clear adjust the nut on the eyebolt. That is the correct degree of tension for the cable p16

19 Safety You are responsible for your own safety. If you don t know basic agriculture & industrial safety, find out. Owners of equipment must by law give operating instructions to other operators such as family members or a hired hand. Making any design changes to equipment could cause a hazard and damage your machine. Wear proper safety equipment. Have handy first aid kit & fire extinguisher. Before working on machine: Turn tractor off Set controls in neutral Remove ignition key Clean all reflectors and lights. Keep all parts clean Replace worn or damaged parts Don t try any makeshift repairs Before operating check that everything is tight and not broken. KILLED, INJURED or SAFE? YOUR CHOICE START UP AND ONGOING CHECK LIST: Grease all fittings Check all bolt tightness Repeat after a days use and check for hydraulic leaks Retorque bolts Adjust hitch height; Set trailer so it is parallel to ground Use a drawbar pin with mechanical retainer Check tire pressure (36 PSI) Oil level in tractor s hydraulic reservoir. Inspect lines, hoses, fitting & couplers. Wipe couplers with clean cloth. TRANSPORTING Use Safety Lights When in transport position make sure transport pin is in place Clean SMV sign and reflectors. MAINTENANCE? HRS Hyd. fluid leaks Damaged hoses Tire pressure 36 PSI HRS Lube points indicated 0 HRS Working points & pins Safety signs clean ANNUAL Bolt tightness Wheel bearings Latch mechanism Cable assembly TORQUE SETTINGS Gr.8 3/8 6 lb-ft /8 3/ 00 /8 60 Hyd. fitting 3/ lb-ft Gr.8.8 M8 0 lb-ft M 0 Gr..9 M 80 lb-ft All hardware - Hex head, Plated, Gr. UNC Hoses - 3/8 female swivel JIC Unless stated otherwise HYDRAULICS Wear gloves and eye protection when searching for leaks. Use a piece of wood or cardboard but not your hand. High pressure oil will penetrate your skin. If that happens you risk serious injury. p1 DECAL REPLACEMENT It is important to understand and follow the information found on all safety decals. If safety decals are damaged, missing, or illedgible they must be replaced. Replacement decals are available by request. Call toll free: Decal # Decal Description 1008 Decal, Degelman 6 x 3/ IN Decal, Caution - 6 Point Safety Decal, Important - Remove Transport Bar 1 Decal, Danger - Stay Clear Crushing Hzd. 1 1 Decal, Important - Position Float Plate 1 1 Decal, Important - End Wheel 1 Decal, Reflector - Amber x 9 IN 6 11 Decal, Landroller Decal, Read Operators Manual 1

20 WARRANTY Degelman Industries warrants this product to the original owner for a period of one (1) year parts and labour and two () years parts from the date of purchase. All matters related to the warranty of our products must be handled through the authorized selling dealer. Warranty does not cover normal wear of the machine components or damages caused by lack of maintenance or misuse, and is subject to the following provisions. REPLACEMENT PARTS: Will be warranted for a period of ninety (90) days. WARRANTY ON MACHINES USED FOR CUSTOM WORK, RENTALS OR INDUSTRIAL USE: Will be warranted as stated above, with the exception that it will be for a period of ninety (90) days only. TIRES: Will be adjusted for warranty by tire manufacturer. LABOUR: Any labour subject to warranty must be authorized by a Degelman representative before work is started. Warranty labour allowance and rates will be handled according to established warranty service policy. GOVERNMENT LEGISLATION: Warranty terms and conditions are subject to Provincial or State legislation. MODIFICATIONS: Warranty will be void if any component is altered or modified, unless written authorization is granted by Degelman Industries Limited. WARRANTY ON ATTACHED EQUIPMENT: No responsibility will be assumed for whatever damages may occur to persons, tractors or property. 0 p18