RTS 27-41ft Assembly and Parts Manual

Transcription

1 RTS 27-41ft Assembly and Parts Manual

2 Table of Contents Salford Recommended Torque Values...5 Torque and Pressure Values for Tires...6 General Safety Precautions...8 Salford and HDM Wing Fold Cuylinder Identification Guide...11 Decal Locations...12 Frame Main Frame Assembly...16 Wing Fold Cylinder Installation th Bar Installation...20 Self Levelling and Depth Control...22 Tongue Installation...24 Telescope Mount Hose Holder...27 Axles 27ft., 30ft. Axle Layout ft., 41ft. Axle Layout lb Main Frame Axle Installation (27ft., 30 ft.) lb Main Frame Axle Installation (27ft., 30 ft.) lb Main Frame Axle Installation (36ft., 41ft.) lb Axle Assembly (27ft., 30ft.) lb Axle Assembly (27ft., 30ft.) lb Tandem Axle Assembly lb Wing Frame Axle Installation lb Axle Assembly lb Axle Assembly lb Axle Assembly lb Hub & Spindle Assembly lb Hub & Spindle Assembly...46 Coulter Assembly Wavy Coulter & Mounts...48 Wavy Coulter & Mounts...49 Coil-Tech Hub...50 Harrow Assembly Harrow Setup...52 Tine Performance Settings Arm Assembly /2 Tine Harrow Assembly Roller Parts

3 Coulter & Harrow Layouts 27ft Coulter Layout ft Harrow Layout ft Coulter Layout ft Harrow Layout ft Coulter Layout ft Harrow Layout ft Coulter Layout ft Harrow Layout...71 Hydraulics & Lights Wing Fold Hydraulics Wing Fold Hydraulics...74 Axle Lift Hydraulics...76 Light Installation...78 Slow Moving Vehicle Sign and Rear Parking Stand...80 Transport Lock...81 Grease Bank...82 Tow Hitch Installation (27ft. - 30ft.)...84 Tow Hitch Installation (36ft. - 41ft.)...85 Tow Hitch Hydraulics (Independent or Shared) Page 3

4 Notes Page

5 Salford Recommended Torque Values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age 5

6 Torque and Pressure Values for Tires WARNING - Maintain proper torque to provide safe and secure attachment of the wheel the hub/drum. Improperly tightened wheel nuts can cause the wheel to separate from the wheel mounting surface during operation. This could result in property damage, serious personal injury, or possibly scenario loss of life. NOTE - if wheel does not have chamfers to match profile of the nuts use flat side of nuts against rim face. Install all lug nuts/bolts by hand to prevent cross threading and tighten lug nuts/bolts following the steps and tightening sequence diagram below. STEP 1. STEP 2. STEP 3. Torque to ft/lbs of torque. Torque to ft/lbs. Torque bolts/nuts to the final ft. lb rating (see bolt size below) Bolt Size (Hub Size) Final Torque 1/2" dia. bolt (up to 3000 lb hubs) 85 ft. lbs 9/16" dia. bolt ( lb hubs) 120 ft. lbs 5/8" dia. bolt ( ,000 lb hubs) 170 ft. lbs 3/4" dia. bolt (16,000-20,000 lb hubs) 300 ft. lbs 7/8" dia. bolt (25,000 lb hubs) ft. lbs Lug Nut/Bolt Tightening Sequence NOTE - Recheck the torque settings of lug nuts/bolts after 10 km (6 miles) and again after 50 km (30 miles). Periodically and at the beginning of each season check the condition and the torque of the lug nuts/bolts. Page

7 Tire Pressure Ensure proper inflation of each tire for safe operation and extended tire life. Pressure Tire Size 35 psi Load Range C 65 psi Load Range D Load Range F 90 psi Truck Tires - 245/70R /70R /60R22-5 NOTE - Periodically and at the beginning of each season check the condition and pressure of each tire Page 7

8 General Safety Precautions Signal Words The words DANGER, WARNING or CAUTION are used with the safety alert symbol. Learn to recognize the safety alerts, and follow the recommended precautions and safe practices. Three words are used in conjunction with the safety-alert symbol: DANGER WARNING CAUTION Indicates an imminently hazardous situation that, if not avoided, will cause DEATH OR VERY SERIOUS INJURY. Indicates a potentially hazardous situation that, if not avoided, could cause DEATH OR SERIOUS INJURY. Indicates a potentially hazardous situation that, if not avoided, may result in MINOR or MODERATE INJURY. Replace any DANGER, WARNING, CAUTION or instructional decal that is not readable or is missing. The location and par t number of these decals is identified later in this section of the manual. The words Important and Note are not related to personal safety but are used to give additional information and tips for operating or servicing this equipment. IMPORTANT: Identifies special instructions or procedures which, if not strictly observed could result in damage to, or destruction of the machine, process or its surroundings. NOTE: Indicates points of particular interest for more efficient and convenient repair or operation. A CAREFUL OPERATOR IS THE BEST INSURANCE AGAINST AN ACCIDENT! Page

9 General Safety Precautions DANGER Wings may fall rapidly causing injury. Always stay clear of wings when being lowered, raised or in a elevated state. Always use lockup device provided when raised. Ensure cylinder is completely filled with hydraulic fluid to avoid unexpected movement. Hydraulics DANGER DO NOT search for high pressure hydraulic leaks without hand and face protection. A tiny, almost invisible leak can penetrate skin, thereby requiring immediate medical attention. Use cardboard or wood to detect leaks never your hands. Double check that all is clear before operating hydraulics. Never remove hydraulic hoses or ends with machine elevated. Relieve hydraulic pressure before disconnecting hydraulic hoses or ends. Maintain proper hydraulic fluid levels. Keep all connectors clean for positive connections. Ensure all fittings and hoses are in good condition. Do not stand under wings. General O Page 9

10 Page

11 Salford and HDM Wing Fold Cuylinder Identification Guide HDM CYLINDERS HS3524A AND HS3536A* WELDED ENDCAP PORTS WELDED TO BARREL WELDED ROD END *Present on all machines with ML suffixed serial numbers beginning with ML SALFORD CYLINDERS HS3524 AND HS3536 THREADED ENDCAP PORTS MACHINED IN GLAND AND ENDCAP THREADED ROD END Page 11

12 Decal Locations RTS DECAL INSTALLATION ALL MACHINES ITEM QTY. DESCRIPTION GD102 2 LARGE SALFORD LOGO WITH WEBSITE GD103 2 RTS MACHINE DECAL GD112 1 ATTENTION: LUBRICATE ALL GREASE FITTING AS PER OPERATOR MANUAL GDSW700 1 WARNING: HIGH PRESSURE FLUID HAZARD GDSW4 1 CAUTION: LIST OF 13 SAFETY FEATURES GDSW2 2 CAUTION: TO AVOID INJURY OR MACHINE DAMAGE GD L X 15 TIRE CAUTION DECAL GDSW115 1 IMPORTANT - AVOID EXCESSIVE DEPTH AND COULTER WHIP GDSW116 1 IMPORTANT - DO NOT EXCEED THE MAXIMUM TILT GD '' x 2 1/2'' RTS PATENT # US 2006/ A1 GD207 1 *RTS-XT ONLY* 1'' x 2 1/2'' PATENT PENDING DECAL 8FT 16FT NO-FOLD MACHINES ITEM QTY. DESCRIPTION GD100 6 LARGE SALFORD LOGO GD HOUR GREASE DECAL GD L X 15 TIRE CAUTION DECAL 16FT SINGLE-FOLD MACHINES ITEM QTY. DESCRIPTION GD100 9 LARGE SALFORD LOGO GD HOUR GREASE DECAL GD111 2 DANGER: STAY CLEAR WHEN FOLDING/UNFOLDING WINGS GDSW200 2 WARNING: OVERHEAD WING HAZARD GD110 1 WARNING: DO NOT LIFT WINGS UNTIL LINES FULL OF OIL AND FREE OF AIR GD L X 15 TIRE CAUTION DECAL 18-30/36-41 SINGLE SOLD MACHINES ITEM QTY. DESCRIPTION GD LARGE SALFORD LOGO GD HOUR GREASE DECAL GD111 2 DANGER: STAY CLEAR WHEN FOLDING/UNFOLDING WINGS GDSW200 2 WARNING: OVERHEAD WING HAZARD GD110 1 WARNING: DO NOT LIFT WINGS UNTIL LINES FULL OF OIL AND FREE OF AIR GD WING LOCK GD193 4/2 11L X 15 TIRE CAUTION DECAL GD194 0/2 12.5L X 15 TIRE CAUTION DECAL BI-FOLD MACHINES ITEM QTY. DESCRIPTION GD LARGE SALFORD LOGO GD HOUR GREASE DECAL GD111 2 DANGER: STAY CLEAR WHEN FOLDING/UNFOLDING WINGS GDSW200 2 WARNING: OVERHEAD WING HAZARD GD110 1 WARNING: DO NOT LIFT WINGS UNTIL LINES FULL OF OIL AND FREE OF AIR GD WING LOCK GD L X 15 TIRE CAUTION DECAL GD L X 15 TIRE CAUTION DECAL Page

13 SALFORD LOGO AND MODEL DECAL LOCATIONS Ensure the tongue-mounted decals are located such that they will not be interfered with by tractor tires 12-24FT Folded Side View 27-41FT Folded Side View (16FT Flat-fold included) (different locations depending on working width) Page 13

14 SALFORD SAFETY DECAL LOCATIONS 36FT- 41FT 12FT- 30FT Mainframe Axle Tower (Wing Axle Towers exclude the DANGER decal) 12FT machine does not require this decal Place Serial No. Plate between 12FT machine does not require this decal Place Below Serial No. Plate RTS-XT ONLY Hose Holder Decal Placement 12FT- 30FT 36FT- 41FT Page

15 SALFORD GREASE DECAL LOCATIONS Mount two 40 Hour Grease Decals on both sides of Upper Telescope Page 15

16 Frame ft RTS & RTS XT Assembly and Parts Manual Main FRAME Frame ASSEMBLY Assembly /4" Page

17 RTS WING Main FRAME Frame INSTALLATION Assembly ITEM NO. QTY. PART NO. DESCRIPTION 1 4 GPH F 1 1/2" x 8 1/4" LG. HARD PLATE PIN 2 4 BL10 5/8" LOCKWASHER 3 4 B1015 5/8 X 1 1/2" PLATED BOLT 4 4 GF1610 1/8" NPT GREASE FITTING 5 8 GBB /4" x 1 1/2" x 2" LG. HARD BUSHING SECURE FRAMES AT LEAST 39" ABOVE THE GROUND CAUTION: OIL ON FRAMES IS VERY SLIPPERY, ESPECIALLY ON NEW PAINT. CLEAN SPILLS IMMEDIATLY TO AVOID A PAINFUL FALL. HINGE PIN INSTALLATION MAKE SURE GREASE NIPPLE IS IN PLACE AND WILL ACCEPT GREASE. 1-SECURE FRAMES AT LEAST 39 inches OFF THE GROUND 2-ALIGN PIN HOLES, INSERT PIN #1 (1 1/2 X 7 1/2" WITH PLATE) 3- FASTEN WITH 5/8X1-1/2" BOLT AND LOCKWASHER Page 17

18 Wing Fold Cylinder Installation 4 5 Refer to hydraulic layout for cylinder sizes Install cylinders with ports facing inwards CAUTION When installing pins, washers must be installed, major damage and or serious injuries or death may occur if washers are not installed properly. Page

19 Wing Fold Cylinder Installation ITEM NO. QTY PART NUMBER DESCRIPTION 1 4 GP16005A05 PIN 1" DIA. x LG. - 2 HOLES 2 8 BF16S 1" SAE WASHER 3 8 BSC0515 5/16" x 1 1/2" COTTER PIN 4 4 GP H04 PIN 1" DIA. x 3 1/4" LG. WITH HEAD 5 4 BSC0415 1/4" x 1 1/2" COTTER PIN CAUTION!!!DO NOT install pins in rods ends until ALL AIR has been purged out of the wing folding hydraulic circuit. See hydraulic layout for instructions. When installing pins, washers must be installed, major damage and or serious injuries or death may occur if washers are not installed. See *Cylinder Series Identification Guide* page for details on types of wingfold cylinders Page 19

20 5th Bar Installation ONLY FOR: 36' AND 41' MODELS Page

21 5th Bar Installation SEE COULTER LAYOUTS FOR 5TH BAR LOCATION Page 21

22 Self Levelling and Depth Control Washer of the depth control rod 26 is shared with cylinder rod pin IMPORTANT Tighten both sides equally, DO NOT OVERTIGHTEN!!! BRACKET WILL BEND!!! OUTLET POPPET Install with boss facing mounting plate OUTLET INLET Page

23 Self Levelling and Depth Control ITEM NO. QTY PART NUMBER DESCRIPTION 1 1 C /570/699/700 TRIPOD TOWER 2 1 C /700 TRIPOD TOWER 3 4 B1025 5/8 x 2 1/2" HEX BOLT GR BN10L 5/8" NYLOCK NUT NC 5 1 C /570/699/700 SELF-LEVELING PIVOT 6 1 C10777 SELF-LEVELING PIVOT - RTS 44 & 50' 7 1 GP A09 PIN 1 1/2" DIA. x 15 1/4" LG. - 2 HOLES 8 2 B0830 1/2" x 3" HEX BOLT 9 2 BN08L 1/2" NYLOCK NUT NC 10 2 HSR " BORE x 9 1/2" STROKE HYD. CYLINDER 11 2 HSR /2" BORE x STROKE HYD. CYLINDER 12 2 HSR4012-TRI 4" BORE x STROKE HYD. CYLINDER 13 1 GP20010A05 1 1/4" DIA. x 10 1/4" LG - 2 HOLE 14 2 BSC0520 5/16" x 2" COTTER PIN 15 2 GPHF H04 1" x 3 3/8" SHOULDER PIN HARDENED W/FLATS 16 2 BSC0415 1/4" x 1 1/2" COTTER PIN 17 1 C TRIPOD BRACE 18 2 GP16006A05 1"DIA. x 6" LG 2 HOLE PIN 19 1 D10011A 1/2 X 2 FB-11 3/4 LG: POPPET VALVE BRACKET D10011B 1/2 X 2 FB-11 3/4 LG: POPPET VALVE BRACKET BU1046 U-BOLT 5/8" x 4" x 7 1/2" LG HPMSC10 STROKE CONTROL VALVE 23 2 B0525 5/16"NC x 2 1/2" HEX BOLT 24 2 BN05L 5/16" LOCK NUT 25 1 C1008 DETENT ADJUSTABLE STOP 26 1 C DEPTH CONTROL ROD 27 1 C ' RTS DEPTH CTRL ROD - 42" WITH CLEVIS 28 2 GBB /4" x 1 1/2" x 2" LG. HARD BUSHING 29 4 BSC0515 5/16" x 1 1/2" COTTER PIN 30 4 GM26 1" MACHINE BUSHING 31 2 GM30 1 1/4" MACHINE BUSHING + 50FT MACHINE ONLY ++ 36/41FT 3 PC & 41FT 5 PC NON HDXT MACHINES /41FT 3 PC & 41FT 5 PC HDXT AND 50FT HDXT/STND MACHINES Page 23

24 Tongue Installation Torque 20 & 22 to ft/lbs CHAIN RING AROUND PIN USE WASHERS AS SHIMS TO TAKE UP CLEARANCE BETWEEN TONGUE AND CLEVIS Page

25 Tongue Installation ITEM NO. QTY PART NUMBER DESCRIPTION C CAST CLEVIS TONGUE 2 1 A INNER TELESCOPE 3 1 A " OUTER TELESCOPE 4 1 A50010 TURNBUCKLE 5 1 PPI-30XL CAT #3 CAST CLEVIS 6 1 PPI-208VR CLEVIS FOR CAT 3 HITCH 7 1 PPI-42XL CAT 4 CAST IRON HITCH 8 1 GJ ,000 LB SAFETY CHAIN 9 1 GP100414C03 5/8'' dia x 4 1/4'' pin RING & WASHER 10 1 GP B06 1 1/4" x 6 1/2" LG. PIN - 1 HOLE 11 1 GP A05 PIN 1" DIA. x 5 1/2" LG. - 2 HOLES 12 2 GP H04 PIN 1" DIA. x 2 5/8" LG. WITH HEAD 13 2 GPSPEC /2" x 8 1/4" LG. WING HINGE PIN 14 2 BSC0515 5/16" x 1 1/2" COTTER PIN 15 2 BSC0415 1/4" x 1 1/2" COTTER PIN 16 1 GHP11 #11 HAIR PIN 17 1 BN06L 3/8"-16NC LOCK NUT 18 1 B0625 3/8" X 2 1/2" LG. GRADE BF16S 1" SAE WASHER 20 1 B1255H 3/4" x 5 1/ HEX BOLT GR BF12HS 3/4" HARD STRUCTURAL WASHER 22 1 BN12S 3/4" STOVER LOCK NUT 23 2 B1015 5/8"NC x 1 1/2" HEX BOLT 24 2 BL10 5/8" LOCKWASHER 25 4 BF16 1" FLAT WASHER 26 2 B1680H 1" x 8" NC HEX BOLT GR BN16L 1-8 NC NYLOCK NUT 28 1 GJ LB TONGUE JACK 29 1 GJ5000S 5000lb JACK WITH ROUND MOUNT 30 1 A60096A TELESCOPE MOUNT HOSE HOLDER ASSEMBLY 31 2 BU0830 1/2" x 3" x 4 1/2" U-BOLT 32 4 BF08HS 1/2" HARD STRUCTURAL FLAT WASHER 33 4 BN08L 1/2" NYLOCK NUT NC NOTE: FOR MACHINES UNDER 30FT USE GJ5000 (29) FOR MACHINES 36FT AND OVER USE GJ8002 (28) Page 25

26 Page

27 Telescope Mount Hose Holder ITEM NO. QTY. PART NO. DESCRIPTION 1 1 A60096 TELESCOPE MOUNT OPERATOR STATION 2 1 G106 HD OPERATORS MANUAL HOLDER 3 1 GL11750 COLE HERSEE LIGHT PLUG HOLDER 4 4 P0160B HOSE CLAMP 4" 5 2 BC0630 3/8"NC x 3" LG. CARRIAGE BOLT 6 2 BN06L 3/8"-16NC LOCK NUT 7 2 BF04 1/4" FLATWASHER 8 5 BC x 1/2" A307A LOW CARBON ZINC CARRIAGE BOLT 9 5 BN02 #10-24 HEX NUT NOTE: EXTRA #4 CLAMPS INSTALLED ON MACHINES REQUIRING MORE THAN TWO SETS OF HOSES Page 27

28 Axles ft RTS & RTS XT Assembly and Parts Manual 27ft., 30ft. Axle Layout WING AXLE *HSR3208 CYLINDER *5000LB PIVOT HUB *4000LB WHEEL HUBS *11L X 15SL TIRES LOAD RANGE 'D' LH WING In this book, all reference to RH or LH assume the operator is behind the machine (as shown here) Right or Left hand? The cylinder lug faces up MAIN AXLE *HSR3508 CYLINDER *10,000LB PIVOT HUB *5000LB WHEEL HUBS *11L X 15FL TIRES 'HIGHWAY SERVICE' LOAD RANGE 'F' WING AXLE *HSR3208 CYLINDER *5000LB PIVOT HUB *4000LB WHEEL HUBS *11L X 15SL TIRES LOAD RANGE 'D' CENTER RH WING FRONT HUB TERMINOLOGY PIVOT HUB WHEEL HUB. Page

29 36ft., 41ft. Axle Layout In this book, all references to Right or Left assume the operator is standing behind the machine looking forward. WING AXLES HSR3708 CYLINDER or HSR3708B CYLINDER 5000LB PIVOT HUB 4000LB WHEEL HUBS 11L X 15SL TIRES 6-BOLT LOAD RANGE 'D' OPTIONAL 245/70R BOLT TIRE MAIN AXLES HSR4008 CYLINDER or HSR4008B CYLINDER 14000LB PIVOT HUB 8000LB WHEEL HUBS 305/70 R22.5 TIRES 8-BOLT HIGHWAY SERVICE LOAD RANGE 'H' OPTIONAL 12.5 X 15 TIRES 8-BOLT HIGHWAY SERVICE LOAD RANGE 'F' WING AXLES HSR3708 CYLINDER or HSR3708B CYLINDER 5000LB PIVOT HUB 4000LB WHEEL HUBS 11L X 15SL TIRES 6-BOLT LOAD RANGE 'D' OPTIONAL 245/70R BOLT TIRE LEFT WING CENTER FRAME RIGHT WING See axle intsallation page for further detail of axle assemblies FRONT Page 29

30 10000lb Main Frame Axle Installation (27ft., 30 ft.) SEE TABLE FOR LENGTH TOWER BRACE REFERENCE TABLE MACHINE SIZE PART # DESCRIPTION INTIAL SETTING 580 MAINFRAME 40' A " TUBE LENGTH 63" PIN TO PIN LENGTH 550 C-SHANK 38' - 40' 550 S-TINE 38' - 40' A " TUBE LENGTH 6 PIN TO PIN LENGTH REFER TO HYDRAULIC LAYOUT FOR CYLINDER SIZE LH SHOWN, RH SIMILAR FOR ORDERING PARTS SEE AXLE ASSEMBLY 6 Page

31 10000lb Main Frame Axle Installation (27ft., 30 ft.) ITEM NO. QTY PART NUMBER DESCRIPTION 1 2 C10013 MAIN FRAME TOWER 2 1 C00139L 10,000 LB S-TINE MAIN AXLE ASSEMBLY - LH 3 1 C00139R 10,000 LB S-TINE MAIN AXLE ASSEMBLY - RH 4 1 C00130L LB AXLE ASSEMBLY - LH 5 1 C00130R LB AXLE ASSEMBLY - RH 6 4 GW5000A 5000 LB HUB AND SPINDLE ASSEMBLY 7 1 SEE TABLE ON PREVIOUS PAGE 8 2 GPH F 1 1/2" x 13 7/8" LG. AXLE PIN - HARDENED 9 2 C50010 TRANSPORT LOCK ASSEMBLY 10 2 C MAINFRAME TURNBUCKLE LOCK 11 4 GP A05 1 1/4" x 5 1/2" PIN - 2 HOLES 12 2 GP C04 RING & WASHER WING LOCK PIN 13 2 GHP9 #9 HAIR PIN 14 2 GP A05 PIN 1" DIA. x 5 1/2" LG. - 2 HOLES 15 2 GPHF H04 1" x 3 1/4" SHOULDER PIN HARDENED W/FLATS 16 2 GP H04 PIN 1" DIA. x 3 1/4" LG. WITH HEAD 17 2 GP H04 PIN 1" DIA. x 2 5/8" LG. WITH HEAD 18 2 B1015 5/8 X 1 1/2" PLATED BOLT 19 4 B1040 5/8"NC x 4" LG. HEX BOLT 20 2 BL10 5/8" LOCKWASHER 21 8 GM30 1 1/4" MACHINE BUSHING 22 8 BSC0520 5/16" x 2" COTTER PIN 23 4 BSC0515 5/16" x 1 1/2" COTTER PIN 24 6 BSC0415 1/4" x 1 1/2" COTTER PIN 25 4 BN10L 5/8" NYLOCK NUT NC 26 4 GBB /4" x 1 1/2" x 2" LG. HARD BUSHING 27 2 GBB /4" x 1 1/2" x 5/8" LG. HARD BUSHING 28 4 GBB /4" x 1 1/2" x 1" LG. HARD BUSHING 29 4 BF16S 1" SAE WASHER CAUTION Connect hoses and charge lift axle cylinders with fluid following the procedure in the axle lift hydraulics section of this manual before connecting rod ends of the cylinders. CAUTION: Torque lug nuts according to decal on axle tower or tire torque page in manual Page 31

32 14000lb Main Frame Axle Installation (36ft., 41ft.) LB SHROT TANDEM AXLE ASSEMBLY (305/70R22.5 TIRES - STANDARD, 12.5L X 15 LOAD RANGE "F" TIRES - OPTIONAL) NOTE: FOR INCREASED TRANSPORT CLEARANCE ON CROWNED ROADS, CLOSE TURNBUCKLES TO 1/4" THREAD EACH END. ADJUST WING TURNBUCKLES ACCORDINGLY. L-PIN NOT NEEDED FOR TURNBUCKLE LOCKS ON MAINFRAME " INTIAL SETTING PIN TO PIN ON TURNBUCKLE COMPLETE ASSEMBLY REFER TO HYDRAULIC SCHEMATIC FOR CYLINDER SIZES LH SHOWN, RH SIMILAR USE THIS HOLE ON BOTH SPINDLES Page

33 14000lb Main Frame Axle Installation (36ft., 41ft.) (305/70 R22.5 TIRES - STANDARD, 12.5LX15 LOAD RANGE "F" - OPTIONAL) ITEM NO. QTY PART NUMBER DESCRIPTION 1 1 C00146L 14,000 LB SHORT TANDEM AXLE ASSEMBLY LH 2 1 C00146R 14,000 LB SHORT TANDEM AXLE ASSEMBLY RH 3 2 C10013 MAIN FRAME TOWER 4 2 A /2" TURNBUCKLE 40" TUBE 5 1 C50010 TRANSPORT LOCK ASSEMBLY 6 4 GP A05 1 1/4" x 5 1/2" PIN - 2 HOLES 7 2 GP C04 RING & WASHER WING LOCK PIN 8 2 GHP9 #9 HAIR PIN 9 4 GPHF H04 1" x 3 3/8" SHOULDER PIN HARDENED W/FLATS 10 2 GP H04 PIN 1" DIA. x 2 5/8" LG. WITH HEAD 11 2 B1015 5/8 X 1 1/2" PLATED BOLT 12 2 BL10 5/8" LOCKWASHER 13 8 GM30 1 1/4" MACHINE BUSHING BSC0520 5/16" x 2" COTTER PIN 15 6 BSC0415 1/4" x 1 1/2" COTTER PIN 16 4 GW8000A 8000 lb GREASABLE HUB AND 14" SPINDLE ASSY 17 4 BN10L 5/8" NYLOCK NUT NC 18 4 B1045 5/8 x 4-1/2" BOLT 19 2 C /2" TURNBUCKLE LOCK 20 2 GBB /4" x 1" x 3/4" LG. HARD BUSHING 21 4 GBB /4" x 1 1/2" x 2" LG. HARD BUSHING 22 4 GBB /4" x 1 1/2" x 5/8" LG. HARD BUSHING 23 4 GBB /4" x 1 1/2" x 1" LG. HARD BUSHING 24 2 GP A05 PIN 1" DIA. x 5 1/2" LG. - 2 HOLES 25 2 GPH F 1 1/2" x 13 7/8" LG. AXLE PIN - HARDENED 26 2 GBB /4" x 1" x 1" LG. HARD BUSHING 27 4 GM26 1" MACHINE BUSHING CAUTION Connect hoses and charge lift axle cylinders with fluid following the procedure in the axle lift hydraulics section of this manual before connecting rod ends of the cylinders. CHECK: Wheel nuts/ lugs for proper tightness. (See torque & pressure values for tires section) Page 33

34 10000lb Axle Assembly (27ft., 30ft.) LH RH Kits 22 and 23 are available on request LH RH Page

35 10000lb Axle Assembly (27ft., 30ft.) ITEM NO. QTY. PART NO. DESCRIPTION 1 1 C7042L LB UPRIGHT BEAM - LH 2 1 C7042R LB UPRIGHT BEAM - RH 3 1 C00129L 10,000 LB WALKING BEAM WITH 5,000LB HUB SLEEVES - LH 4 1 C00129R 10,000 LB WALKING BEAM WITH 5,000LB HUB SLEEVES - RH 5 1 GW12110VW 10000/12000 LB GRASS WRAP GUARD 6 1 GW12110VS 10000/12000 LB V-SEAL 7 1 GW12110VC 10000/12000 LB COUNTERFACE 8 1 GB LB CONE, LB INNER CONE 9 1 GB LB CUP, LB INNER CUP 10 1 GB LB OUTER CUP 11 1 GB LB OUTER CONE 12 1 BF20S 1 1/4" SAE WASHER 13 1 BN20SF 1 1/4"NF SLOTTED HEX NUT 14 1 BSC0425 1/4" x 2 1/2" COTTER PIN 15 1 GW ,000 LB DUST CAP 19 1 GF1610 1/8" NPT GREASE FITTING 16 2 GW5000A 5000 LB HUB AND SPINDLE ASSEMBLY 17 2 B1045 5/8 x 4-1/2" BOLT 18 2 BN10L 5/8" NYLOCK NUT NC 20 1 GBB /4" x 1" x 3/4" LG. HARD BUSHING 21 2 GBB /4" x 1 1/2" x 2" LG. HARD BUSHING 22 1 GW12110V 10000/12000 LB V-SEAL KIT 23 1 GW9111V LB BEARING WITH V-SEAL KIT FRONT LH AXLE ASSEMBLY RH AXLE ASSEMBLY Page 35

36 14000lb Tandem Axle Assembly LB SHROT TANDEM AXLE ASSEMBLY (305/70R22.5 TIRES - STANDARD, 12.5L X 15 LOAD RANGE "F" TIRES - OPTIONAL) LH 1 RH LH USE INNER HOLE FOR FRONT AND REAR SPINDLES RH 4 Page

37 14000lb Tandem Axle Assembly LB SHROT TANDEM AXLE ASSEMBLY (305/70R22.5 TIRES - STANDARD, 12.5L X 15 LOAD RANGE "F" TIRES - OPTIONAL) ITEM NO. QTY PART NUMBER DESCRIPTION 1 1 C00110L 14,000 LB UPRIGHT BEAM - LH 2 1 C00145L 14,000 LB SHORT WALKING BEAM - LH 3 1 C00110R LB UPRIGHT BEAM - RH 4 1 C00145R 14,000 LB SHORT WALKING BEAM - LH 5 2 GW8000A 8000 lb GREASABLE HUB AND 14" SPINDLE ASSY 6 1 GB ,000 LB INNER CONE 7 1 GB ,000 LB INNER CUP 8 1 GW14110VC LB V-SEAL COUNTERFACE 9 1 GW ,000 LB DUST CAP 10 1 BN28SF 1 3/4" NF SLOTTED FLANGE NUT 11 1 BSR0527 5/16" x 2 3/4" ROLL PIN 12 1 GB LB CONE, LB INNER CONE 13 1 GB LB CUP, LB INNER CUP 14 4 B0505 5/16"NC x 1/2" LG. HEX BOLT 15 1 GW14112S 14,000 LB DUST CAP SEAL 16 2 B1045 5/8 x 4 1/2" HEX BOLT GR BN10L 5/8" NYLOCK NUT NC 18 2 GBB /4" x 1 1/2" x 2" LG. HARD BUSHING 19 1 GBB /4" x 1" x 3/4" LG. HARD BUSHING 20 1 GW14110VS 14,000 LB V-SEAL 21 1 GW14110VW LB V-SEAL GRASS WRAP GUARD 22 1 GF641 1/4"-28NF GREASE FITTING 23 1 GF1610 1/8" NPT GREASE FITTING 24 1 GW14110V 14,000 LB V-SEAL KIT 25 1 GW LB BEARING KIT FRONT LH AXLE ASSEMBLY RH AXLE ASSEMBLY Page 37

38 5000lb Wing Frame Axle Installation LH SHOWN INITIAL SETTING OF 54" FROM PIN TO PIN REFER TO HYDRAULIC SCHEMATIC FOR CYLINDER SIZES RH 5 LH ' SINGLE AXLE LH RH COMPLETE ASSEMBLY PARTS BREAKDOWN ON FOLLOWING PAGES 15 SINGLE OR DUAL AXLE (EXCEPT 18ft) Page

39 ITEM NO. QTY. PART NO. DESCRIPTION 1 1 C4540WL 5000 LB WING AXLE ASSEMBLY - LH 2 1 C4540WR 5000 LB WING AXLE ASSEMBLY - RH 3 1 C LB SINGLE OR DUAL AXLE 4 1 C0543L 17' CULTIVATOR AND 18' RTS RH SINGLE WHEEL AXLE 5 1 C0543R 17' CULTIVATOR AND 18' RTS RH SINGLE WHEEL AXLE 6 1 C4547B TOWER,450/550/570 WING 7 1 A /4" TURNBUCKLE - 4 TUBE 8 1 GPH F 1 1/4" x 13 1/2" LG. AXLE PIN - HARDENED 9 1 BL10 5/8" LOCKWASHER 10 1 B1015 5/8 X 1 1/2" PLATED BOLT 11 1 GPHF H04 1" x 3 1/4" SHOULDER PIN HARDENED W/FLATS 12 2 GP H04 PIN 1" DIA. x 3 1/4" LG. WITH HEAD 13 4 BSC0415 1/4" x 1 1/2" COTTER PIN 14 1 GP H04 PIN 1" DIA. x 2 5/8" LG. WITH HEAD 15 2 GW4000A 4000 LB HUB AND SPINDLE ASSEMBLY 16 2 B0835 1/2 X 3 1/2" BOLT 17 2 BN08L 1/2" NYLOCK NUT NC 18 2 GBB /2" x 1 1/4" x 1" LG. HARD BUSHING 19 2 GBB /4" x 1" x 3/4" LG. HARD BUSHING 20 1 FL00051 LIGHT TURNBUCKLE LOCK 21 1 GP L03 1/2" x 3 1/2" PARKING STAND PIN 22 1 GHP11 #11 HAIR PIN QUANTITIES SHOWN ARE FOR ONE WING AXLE INSTALLATION Note orientation of lugs on axle towers (Left/Right). 1. Line up axle tower and upright of tandem axle assembly with lugs on wing frame. Insert 1 1/4" x 13" pin through tower and axle. Retain pin with 5/8" x 1 1/2" hex bolt and 5/8" lockwasher. 2. Set wing turnbuckle to 54 inches pin to pin. Connect turnbuckle with 1" x 2 5/8" head pins and 1/4" x 1 1/2" cotter pins. 3. Attach 3 1/4" bore x 8" stroke hydraulic cylinder to axle tower with 1" x 3 1/4" head pin and 1/4" x 1 1/2" cotter pin. The rod end may remain loose until cylinders are charged. 4. Insert removeable 4000 lb hub and spindle assemblies into axles and retain with 1/2" x 3 1/2" hex bolts and 1/2" locknuts. Salford uses hard press-in bushings to reduce permanent wear. At a time that the bushings are to be replaced, hammer out old bushings taking care not to scar the frame. New bushings will need to be hammered in as they are spring-loaded by design. Hubs are greased at shipping. WING TANDEM AXLE INSTALLATION 5000lb Wing Frame Axle Installation Page 39

40 5000lb Axle Assembly 18' SINGLE AXLE SINGLE OR DUAL AXLE (EXCEPT 18') LH RH LH RH LEFT SHOWN Page

41 5000lb Axle Assembly Page 41

42 5000lb Axle Assembly Page

43 5000lb Axle Assembly ITEM QTY PART NO. DESCRIPTION 1 1 GW LB SPINDLE-14 IN. LG 2 1 GW5110VW 5000 LB V-SEAL GRASS WRAP GUARD 3 1 GW5110VS 5000 LB V-SEAL 4 1 GW5110VC 5000 LB SEAL COUNTERFACE 5 1 GB /5500 LB INNER CONE 6 1 GB /5500 LB INNER CUP 7 1 GB /5500 LB OUTER CUP, 3000 LB INNER CUP 8 1 GB /5500 LB OUTER CONE, 3000 LB INNER CONE 9 1 BF16-9 1" HARD SAE FLAT WASHER GR.9 PLATED 10 1 BN16SF 1" NF SLOTTED HEX NUT 11 1 BSC0317 3/16" x 1 3/4" COTTER PIN 12 1 GW /5500 LB DUST CAP 13 6 BW0912 9/16"-18 x 1 1/4" WHEEL BOLT 14 1 GW5110V 5000 LB V-SEAL KIT 15 1 GW5111V 5000 LB BEARING WITH V-SEAL KIT 16 1 GW5000B 5000 LB HUB WITH BEARINGS, SEAL, & DUST CAP Complete assembly available as part number GW5000A (includes hub, spindle, bearings, seals, dust cap, and hardware) Page 43

44 4000lb Hub & Spindle Assembly Page

45 4000lb Hub & Spindle Assembly ITEM QTY PART NO. DESCRIPTION 1 1 GW LB SPINDLE - 10" LG. 2 1 GW4110VW 4000 LB GRASS WRAP 3 1 GW4110VS 4000 LB V-SEAL 4 1 GW4110VC 4000 LB SEAL COUNTER FACE 5 1 GB LB INNER CONE 6 1 GB LB INNER CUP 7 1 GB LB OUTER CUP 8 1 GB LB OUTER CONE 9 1 BF16-9 1" HARD SAE FLAT WASHER GR.9 PLATED 10 1 BN16JS 1"-14NF SLOTTED JAM NUT 11 1 BSC0317 3/16" x 1 3/4" COTTER PIN 12 1 GW LB DUST CAP 13 6 BW0912 9/16"-18 x 1 1/4" WHEEL BOLT 14 1 GW4110V 4000 LB V-SEAL KIT 15 1 GW4111V 4000LB BEARING WITH V-SEAL KIT 16 1 GW4000B 4000 LB HUB WITH BEARINGS, SEAL, & DUST CAP Complete assembly available as part number GW4000A (includes hub, spindle, bearings, seals, dust cap, and hardware) Page 45

46 8000lb Hub & Spindle Assembly Page

47 8000lb Hub & Spindle Assembly ITEM NO. QTY PART NUMBER DESCRIPTION 1 1 GW8014 SPINDLE, LBS. 2 1 GW8110VW 8000 LB V-SEAL GRASS WRAP GUARD 3 1 GW8110VS 8000 LB V-SEAL 4 1 GW8110VC 8000 LB V-SEAL COUNTERFACE 5 1 GB INNER CONE 6 1 GB INNER CUP 7 1 GB OUTER CUP 8 1 GB OUTER CONE 9 1 GW8108 1" SPINDLE WASHER 10 1 BN16S 1" SLOTTED HEX NUT 11 1 BSC0317 3/16" x 1 3/4" COTTER PIN 12 1 GW DUST CAP 13 8 BW1020 5/8" x 2" PRESS-IN WHEEL STUD 14 8 BW10 5/8" WHEEL LUG NUT 15 1 GW LB HUB WITH BEARINGS, V-SEAL, & DUSTCAP 16 1 GW8110V 8000 LB V-SEAL KIT 17 1 GW8111V 8000 LB BEARING WITH V-SEAL KIT Entire assembly available as part number GW8000A (includes hub, spindle, bearings, seal, dust cap, and hardware) Page 47

48 Coulter Assembly ft RTS & RTS XT Assembly and Parts Manual Wavy Coulter & Mounts NO WASHERS IF USING LOCKING COLLAR 10! This bolt must be loose so that the coulter can swivel easily. However, the bolt must be tight if the "nonswivel collar" 10 is used RIGHT LEFT LEFT RIGHT As viewed from rear of machine! Must be stover locknuts (crimp type) Nylon locknuts are too long and will not engage. When substituting optional drop mount 2 be sure to follow coulter layout with regard to where non-swivel coulters are located. Page

49 Wavy Coulter & Mounts ITEM NO. QTY. PART NO. DESCRIPTION 1 1 C90120 RTS COULTER MOUNT 2 1 C90150 RTS DROP COULTER MOUNT 3 1 A8050LWA LEFT COIL WITH SPINDLE AND HUB 4 1 A8050RWA RIGHT COIL WITH SPINDLE AND HUB 5 2 GBW WEAR BAND-1 1/2 OD X 1 1/4 ID-1/2 LG 6 1 CT COIL-TECH COULTER 17" 8 WAVE 1 3/4" WAVE 7 1 CT COIL-TECH COULTER 17" 13 WAVE 3/4" WAVE 8 1 CT COIL-TECH COULTER 20" 8 WAVE 2" WAVE 9 1 CT COIL-TECH COULTER 20" 13 WAVE 3/4" WAVE 10 1 C90125 RTS CAST MOUNT SWIVEL STOP 11 2 BU1061 U-BOLT 5/8" x 6" x 5 1/2" 12 4 BN10L 5/8" NYLOCK NUT NC 13 2 BF08HS 1/2" HARD STRUCTURAL FLAT WASHER 14 1 B0832ST 1/2"-13NC x 3 1/4" SHORT THREAD BOLT 15 5 BN08S 1/2"-13NC STOVER LOCK NUT 16 4 B0825 1/2" x 2 1/2" HEX BOLT Page 49

50 COIL-TECH C90101 Coil-Tech EXPLODED Hub VIEW ! TIGHTEN SPINDLE NUT TO 70ft-Lbs DO NOT BACK OFF AFTER TIGHTENING Page

51 Coil-Tech Hub ITEM NO. QTY. PART NO. DESCRIPTION 1-12 C90101AS CAST COIL-TECH COULTER HUB COMPLETE (includes spindle) 1 1 C90105 COIL-TECH COULTER SPINDLE FOR CAST HUB 2 1 C9111VW GRASS WRAP 3 1 C9111VS V-SEAL 4 1 C9111VC SEAL COUNTER FACE 5 1 GBS OIL SEAL 6 2 GB BEARING 7 1 C90006 RTS COULTER BEARING SPACER 8 1 C90101 CAST COIL-TECH COULTER HUB 9 1 GF641 1/4"-28NF GREASE FITTING 10 1 BSC0415 1/4" x 1 1/2" COTTER PIN 11 1 C90102 DUST CAP-PRESS ON 12 4 B0825 1/2" x 2 1/2" HEX BOLT 13 4 BN08S 1/2"-13NC STOVER LOCK NUT 14 1 BN16FCH 1"-14NF FLANGED CASTLE NUT GR. 8 2, 3, 4, 5 C9111VA V-SEAL KIT (includes grass wrap, v-seal, counter face and oil seal) 6.7 C91115 BEARING KIT (2 x 6208 bearings and bearing spacer) 2,3,4,5,6,7 C90020 COIL-TECH COULTER BEARING, V-SEAL AND SPACER KIT C9111VA - V-SEAL KIT! TIGHTEN SPINDLE NUT TO 70ft-Lbs DO NOT BACK OFF AFTER TIGHTENING C COIL-TECH BEARINGS, V-SEAL AND SPACER KIT. C BEARING KIT (COIL TECH) Page 51

52 Harrow Assembly 4 ITEM NO. PART NO. DESCRIPTION HARROW Harrow SETUP Setup 2 3 USE BOTTOM HOLE FOR ROLLER STOP HOLD SPRING BACK WITH TOOL AND SET POSITION WITH #9 HAIR PINS BOLT HARROW SPRING TOOL WITH U-BOLT. DO NOT HANG ON WING OR IT WILL FALL OFF WHEN FOLDED 1 A 1 BU1061 U-BOLT 5/8x6x5-1/2" 2 BU1020 U-BOLT 5/8x2x3" 3 BU0825 U-BOLT 1/2x2-1/2X3-1/2" A: USE SLOTS FOR 20" BLADES. (MOUNT WITH BRACKET PUSHED ALL THE WAY UP SO THAT THE U-BOLT SITS IN LOWER PART OF THE SLOT) NOTICE: 16' & 50' MACHINES USE THIS POSITION FOR 17" & 20" BLADES. B: USE NEXT HOLE DOWN FOR 17" BLADES. EXCEPT ON 16' & 50' MACHINES. (17" BLADE POSITION SHOWN BELOW) PLACE TINE HARROW PIN HERE (BOTTOM HOLE) RB0025 A60105 RB0026 SET RAKE ANGLE B 5/8" HARD STRUCTURAL 4 BF10HS FLAT WASHER USE NYLON LOCKNUTS PROVIDED A B Page

53 Tine Performance Settings For better trash flow, the tines are adjustable in 2 ways: use bottom bolt hole for 'standard' setting. Shown here is the 'standard' setting use top bolt hole to angle tines Here the tine section is angled by changing the bolt hole used. This Angle-Iron has two sets of holes. Here the rake angle is varied This set of holes is the 'standard' setting. 1" 1" 3/4" 5/8" Using this set of holes will vary the rake angle as shown above. FRONT Page 53

54 62 Arm Assembly STANDARD POSITION AS SHOWN FLIP SPACER OVER FOR S-TINES Page

55 62 Arm Assembly + + ITEM NO. QTY. PART NO. DESCRIPTION 1 1 R30012 PARALLEL LINKAGE BAR 2 1 R30006 PARALLEL LINKAGE ARM 3 1 R80099 HEAD,SALFORD HARROW FOR 5/8" UPPER PIVOT BOLT 4 1 R " HARROW ARM FOR 5/8" PIVOT AND U-BOLTS 5 1 R80100A 62" HARROW ARM W/ KIT (REPLACES RB1125) 6 5 BC0835H 1/2" X 13NC X 3-1/2" LG. CARRIAGE BOLT GR. 5 SHORT THREAD 7 4 R0030 NYLON BUSHING 3/4" OD x 1/2" ID x 1.94 LG. 8 5 BN08L 1/2" NYLOCK NUT NC 9 2 BN10L 5/8" NYLOCK NUT NC 10 1 GP L03 1/2" x 3 1/2" PARKING STAND PIN 11 1 GHP11 #11 HAIR PIN 12 2 R0035 2" x 10" HARROW ARM SPRING 13 1 R80128 ROLLER ARM STOP BRACKET (LONG) 14 1 R80037L TINE SECTION UPRIGHT PLATE LEFT 15 1 R80037R TINE SECTION UPRIGHT PLATE RIGHT 16 1 R0028 STEEL HEAD SPACER 2 1/8" LG B1037ST 5/8" - 11NC X 3 3/4" SHORT THREAD BOLT 18 1 R /8"OD NYLATRON BUSHING 19 1 R /8"OD "ID NYLATRON ROD 20 1 R80096 HARROW ARM SPACER 21 2 RB0021 TIGHTENER,SINGLE SPRING 22 2 B0615 3/8" X 1 1/2" LG. GRADE BN06L 3/8"-16NC LOCK NUT 24 2 GHP9 #9 HAIR PIN 25 1 B1045 5/8 x 4 1/2" HEX BOLT GR 5 NOTES: + + USE R80130 FOR S-TINE CULTIVATORS Page 55

56 1/2 Tine Harrow Assembly FOR ENDS OF FRONT TUBE ONLY OPTIONAL SECOND TUBE FOR WEIGHT TINE ANGLE ADJUSTER SHOWN HERE ON INNER LEFT. SEE HARROW LAYOUT FOR MACHINE SPECIFIC POSITIONS FOR ADJUSTOR MOUNTS ONLY ALL OTHER POSITIONS 16 Page

57 1/2 Tine Harrow Assembly 1/2" - 3 TINE HARROW ASSEMBLY PART NO. R633 ITEM NO. PART NO. DESCRIPTION 1 U TUBE 2 1/2 x 2 1/2 x 3/16"W x 54" LG. 2 R6063 TINE PIPE FOR 1/2" (3-TINE) 1/2" - 4 TINE HARROW ASSEMBLY PART NO. R634 ITEM NO. PART NO. DESCRIPTION 1 U TUBE 2 1/2 x 2 1/2 x 3/16"W x 72" LG. 2 R6064 TINE PIPE FOR 1/2" (4-TINE) 1/2" - 5 TINE HARROW ASSEMBLY PART NO. R635 ITEM NO. PART NO. DESCRIPTION 1 U TUBE 2 1/2 x 2 1/2 x 3/16"W x 92" LG. 2 R6065 TINE PIPE FOR 1/2" (5-TINE) 1/2" - 6 TINE HARROW ASSEMBLY PART NO. R636 ITEM NO. PART NO. DESCRIPTION 1 U TUBE 2 1/2 x 2 1/2 x 3/16"W x 1 LG. 2 R6066 TINE PIPE FOR 1/2" (6-TINE) COMMON PARTS ITEM NO. PART NO. DESCRIPTION 3 R /2" TINE TUBE CONNECTOR 4 R30011 CLAMP BRACKET 5 B0812 1/2 X 1 1/4" BOLT 6 BN08L 1/2" NYLOCK NUT NC 7 BU1025 U-BOLT 5/8" x 2 1/2" x 4" 8 BN10L 5/8" NYLOCK NUT NC 9 R /2" WIRE - 20" DBL LEG SPRING TINE 10 R30007 ADJUSTING BRACKET WELDMENT 11 R /2" TINE 3 BAR ADJUST CONNECTOR 12 R30010 ADJUSTING BAR HD 3 BAR TINE 13 R30008 ADJUSTING BRACKET HANDLE WELDMENT 14 R OD x.438 ID X 3/4 LONG SPACER 15 B0640 3/8"NC x 4" LG. HEX BOLT 16 BN06S 3/8"-16NC STOVER LOCK NUT 17 B0635 3/8"NC x 3 1/2" LG. HEX BOLT 18 R30015 LIGHT SAVER BRACKET 19 B0630 3/8"NC x 3" HEX BOLT 20 B0815 1/2" x 1 1/2" HEX BOLT 21 GHP11 #11 HAIR PIN Page 57

58 14 Roller Parts PT# GD1071 SALFORD Decal on frame tube facing rear 2 PT# GD HR Install grease decal towards rear of frame Install bearing with grease fitting facing rear of roller Arrow shows roller rotation direction 1 (5' ROLLER SHOWN) Page

59 14 Roller Parts 14" ROLLER HARROW ASSEMBLY - 3' 0" (91.4) LONG COMPLETE ASSEMBLY PART NO. MR80143(L/R) ITEM NO. QTY. PART NO. DESCRIPTION 1 1 R80147R 3' ROLLER ONLY RIGHT HAND SPIRAL, 14" DIA. 2 1 R ' ROLLER FRAME FOR 14" ROLLER 3 2 A /4" x 1 1/2" x 1 19/32"LG BUSHING 4 2 GB491-B 1 1/2" BEARING COMPLETE 5 2 BN20JL 1 1/4"NC JAM LOCK NUT 6 6 BC0812H CARRIAGE BOLT 1/2"NC x 1 1/4" LG. GR BN08S 1/2"-13NC STOVER LOCK NUT 14" ROLLER HARROW ASSEMBLY - 4' 0" (121.9) LONG COMPLETE ASSEMBLY PART NO. MR80144(L/R) ITEM NO. QTY. PART NO. DESCRIPTION 1 1 R80148R 4' ROLLER ONLY RIGHT HAND SPIRAL, 14" DIA. 2 1 R ' ROLLER FRAME FOR 14" ROLLER 3 2 A /4" x 1 1/2" x 1 19/32"LG BUSHING 4 2 GB491-B 1 1/2" BEARING COMPLETE 5 2 BN20JL 1 1/4"NC JAM LOCK NUT 6 6 BC0812H CARRIAGE BOLT 1/2"NC x 1 1/4" LG. GR BN08S 1/2"-13NC STOVER LOCK NUT 14" ROLLER HARROW ASSEMBLY - 5' 0" (152.4) LONG COMPLETE ASSEMBLY PART NO. MR80145(L/R) ITEM NO. QTY. PART NO. DESCRIPTION 1 1 R80149R 5' ROLLER ONLY RIGHT HAND SPIRAL, 14" DIA. 2 1 R ' ROLLER FRAME FOR 14" ROLLER 3 2 A /4" x 1 1/2" x 1 19/32"LG BUSHING 4 2 GB491-B 1 1/2" BEARING COMPLETE 5 2 BN20JL 1 1/4"NC JAM LOCK NUT 6 6 BC0812H CARRIAGE BOLT 1/2"NC x 1 1/4" LG. GR BN08S 1/2"-13NC STOVER LOCK NUT 14" ROLLER HARROW ASSEMBLY - 6' 2" (187.9) LONG COMPLETE ASSEMBLY PART NO. MR80146(L/R) ITEM NO. QTY. PART NO. DESCRIPTION 1 1 R80150R 6'2" ROLLER ONLY RIGHT HAND SPIRAL, 14" DIA. 2 1 R '2" ROLLER FRAME FOR 14" ROLLER 3 2 A /4" x 1 1/2" x 1 19/32"LG BUSHING 4 2 GB491-B 1 1/2" BEARING COMPLETE 5 2 BN20JL 1 1/4"NC JAM LOCK NUT 6 6 BC0812H CARRIAGE BOLT 1/2"NC x 1 1/4" LG. GR BN08S 1/2"-13NC STOVER LOCK NUT Page 59

60 Coulter & Harrow Layouts 51" ft RTS & RTS XT Assembly and Parts Manual IMPORTANT!! NOTE WHICH SIDE OF BEAM TO MOUNT THE COULTER FOR MACHINES WITH BOTH 13 & 8 WAVE COULTERS, INSTALL THE 13 WAVE COULTERS ON THE FRONT, AND THE 8 WAVE COULTERS ON THE REAR 47 COULTERS 37 SWIVEL 10 RIDGID NOTE: CENTER COILS MAY BE RH OR LH KEEP HUBS POINTING OUTWARD. BEGIN IN CENTER OF MACHINE LEGEND 100LBS WEIGHT KIT LAYOUT SHOWS MAXIMUM WEIGHTS ADDED (50LBS/FT) NON-SWIVELLING SPRING MOUNT NON-SWIVEL SWIVEL USE HARDENED WASHERS LEAVE BOLT LOOSE TO ALLOW SWIVEL. 11" Must be Rigid straddle beam 27FT 570 RTS COULTER SPACING Must be Rigid straddle beam 27ft Coulter Layout 51" 13" 47" 13" 19" 19" 47" 8" 21" 8" 13" 11" 9" 4" 6" 6" 4" 4" 6" 6" 4" 9" 23 BLADES 24 BLADES 13" Page

61 51" 47" 19" 19" 47" 51" 19" 13" 13" 8" 21" 8" 13" 13" 19" 11" 11" 9" 9" Must be Rigid straddle beam 6" 6" Must be Rigid straddle beam 27FT 570 RTS COULTER SPACING - DUAL AXLES 4" 4" 6" 4" 4" 6" 19" 19" LEGEND 23 BLADES 47 COULTERS 37 SWIVEL 10 RIDGID 100LBS WEIGHT KIT LAYOUT SHOWS MAXIMUM WEIGHTS ADDED (50LBS/FT) NOTE: CENTER COILS MAY BE RH OR LH NON-SWIVELLING SPRING MOUNT 24 BLADES IMPORTANT!! KEEP HUBS POINTING OUTWARD. BEGIN IN CENTER OF MACHINE FOR MACHINES WITH BOTH 13 & 8 WAVE COULTERS, INSTALL THE 13 WAVE COULTERS ON THE FRONT, AND THE 8 WAVE COULTERS ON THE REAR NOTE WHICH SIDE OF BEAM TO MOUNT THE COULTER NON-SWIVEL SWIVEL USE HARDENED WASHERS LEAVE BOLT LOOSE TO ALLOW SWIVEL Page 61

62 27ft SALFORD Harrow Layout 27ft 570 RTS HARROW LAYOUT Tine angle adjuster Set tine rake angle Roller Spring Adjuster. Bolt on center frame A B A B 20" BLADES: USE SLOT (A) 17" BLADES: USE NEXT HOLE DOWN(B) Tine angle adjuster 1" 2-3" 1" 2-3" 1" 23" 18" 30" 31" 39" 32" 39" 31" 30" 18" 23" 5 TINE R635 3 TINE R633 4 TINE R634 5 TINE R635 3ft ROLLER MR80143R 4ft ROLLER MR80144R 6ft 2in ROLLER MR80146R 6ft 2in ROLLER MR80146R 4ft ROLLER MR80144R 3ft ROLLER MR80143R Page

63 6 47" 19" 19" 47" 6 21" 13" 8" 8" 13" 13" 21" 13" 11" 6" 21" 6" 11" STRADDLE BEAM 9" 9" 4" 4" STRADDLE BEAM ft RTS & RTS XT Assembly and Parts Manual 30ft SALFORD Coulter Layout 30FT 570 RTS COULTER SPACING 4" 4" 6" 6" 27 BLADES LEGEND 53 COULTERS 43 SWIVEL 10 RIGID 100LBS WEIGHT KIT LAYOUT SHOWS MAXIMUM WEIGHTS ADDED (50LBS/FT) NOTE: CENTER COILS MAY BE RH OR LH 26 BLADES NON-SWIVELLING SPRING MOUNT IMPORTANT!! KEEP HUBS POINTING OUTWARD. BEGIN IN CENTER OF MACHINE FOR MACHINES WITH BOTH 13 & 8 WAVE COULTERS, INSTALL THE 13 WAVE COULTERS ON THE FRONT, AND THE 8 WAVE COULTERS ON THE REAR NOTE WHICH SIDE OF BEAM TO MOUNT THE COULTER NON-SWIVEL SWIVEL USE HARDENED WASHERS LEAVE BOLT LOOSE TO ALLOW SWIVEL Page 63

64 6 47" 19" 19" 47" 6 19" 21" 13" 8" 8" 13" 13" 21" 13" 19" 11" 6" 21" 6" 11" 30FT STRADDLE BEAM 9" 9" 4" 4" STRADDLE BEAM ft RTS & RTS XT Assembly and Parts Manual SALFORD 570 RTS COULTER SPACING - DUAL AXLES 4" 4" 6" 19" 19" 6" LEGEND 27 BLADES 53 COULTERS 45 SWIVEL 8 RIGID 100LBS WEIGHT KIT LAYOUT SHOWS MAXIMUM WEIGHTS ADDED (50LBS/FT) NOTE: CENTER COILS MAY BE RH OR LH NON-SWIVELLING SPRING MOUNT 26 BLADES KEEP HUBS POINTING OUTWARD. BEGIN IN CENTER OF MACHINE IMPORTANT!! FOR MACHINES WITH BOTH 13 & 8 WAVE COULTERS, INSTALL THE 13 WAVE COULTERS ON THE FRONT, AND THE 8 WAVE COULTERS ON THE REAR NOTE WHICH SIDE OF BEAM TO MOUNT THE COULTER NON-SWIVEL SWIVEL USE HARDENED WASHERS LEAVE BOLT LOOSE TO ALLOW SWIVEL. Page

65 30ft Harrow SALFORD Layout 30ft 570 RTS HARROW LAYOUT Tine angle adjuster 44" 16" 6 Tine R636 5ft Roller MR80145R 1" 32" 4ft Roller MR80144R A Set tine rake angle Roller Spring Adjuster. Bolt on center frame B A B 20" BLADES: USE SLOT (A) 17" BLADES: USE NEXT HOLE DOWN(B) Tine angle adjuster 2-3" 1" 2-3" 1" 30 1/2" 39" 32" 39" 30 1/2" 32" 16" 44" 3 Tine R633 4 Tine R634 6 Tine R636 6ft 2in Roller MR80146R 6ft 2in Roller MR80146R 4ft Roller MR80144R 5ft Roller MR80145R Page 65

66 36ft Coulter Layout SALFORD 36ft RTS /2" 40 1/2" 37" 37" 40 1/2" 56 1/2" 2 118" 9" 182" 2 10" 18 1/2" 19 1/2" 9" 118" 19 1/2" 18 1/2" 10" 2 6" 12 1/2" 12 1/2" 6" 6 1/2" 5 1/2" 4 1/2" 4" 4 1/2" 4 1/2" 5 1/2" 6 1/2" 4" 4 1/2" 10" 10" 12 1/2" 12 1/2" 11 1/2" 11 1/2" 10" 10" 3" 3" 14" 3" 31" 14" 3" 4 1/2" 4 1/2" 3" 7" 10" 3" 7" 7" 7" 7" 7" 10" 31" 21" 21" 12 1/2" 21" 21" 12 1/2" LEGEND 100LBS WEIGHT KIT LAYOUT SHOWS MAXIMUM WEIGHTS ADDED (50LBS/FT) NON-SWIVELLING SPRING MOUNT 30 BLADES 32 BLADES 62 COULTERS 52 SWIVEL 10 RIGID NOTE: CENTER COILS MAY BE RH OR LH NON-SWIVEL SWIVEL USE HARDENED WASHERS LEAVE BOLT LOOSE TO ALLOW SWIVEL. IMPORTANT!! NOTE WHICH SIDE OF BEAM TO MOUNT THE COULTER FOR MACHINES WITH BOTH 13 & 8 WAVE COULTERS, INSTALL THE 13 WAVE COULTERS ON THE FRONT, AND THE 8 WAVE COULTERS ON THE REAR KEEP HUBS POINTING OUTWARD. BEGIN IN CENTER OF MACHINE Page

67 SALFORD 36FT 570 RTS COULTER SPACING - DUAL AXLES /2" 40 1/2" 37" 37" 40 1/2" 56 1/2" 2 118" 9" 182" 9" 118" 2 10" 18 1/2" 19 1/2" 19 1/2" 18 1/2" 10" 2 6" 12 1/2" 12 1/2" 6" 6 1/2" 5 1/2" 4 1/2" 4" 4 1/2" 4 1/2" 5 1/2" 6 1/2" 4" 4 1/2" 10" 12 1/2" 12 1/2" 10" 11 1/2" 11 1/2" 10" 10" 3" 3" 14" 3" 31" 14" 3" 4 1/2" 4 1/2" 3" 7" 10" 3" 7" 7" 7" 10" 31" 7" 12 1/2" 21" 21" 12 1/2" 7" 21" 21" LEGEND 100LBS WEIGHT KIT LAYOUT SHOWS MAXIMUM WEIGHTS ADDED (50LBS/FT) NON-SWIVELLING SPRING MOUNT 30 BLADES 32 BLADES 62 COULTERS 52 SWIVEL 10 RIGID NOTE: CENTER COILS MAY BE RH OR LH NON-SWIVEL SWIVEL USE HARDENED WASHERS LEAVE BOLT LOOSE TO ALLOW SWIVEL. IMPORTANT!! NOTE WHICH SIDE OF BEAM TO MOUNT THE COULTER FOR MACHINES WITH BOTH 13 & 8 WAVE COULTERS, INSTALL THE 13 WAVE COULTERS ON THE FRONT, AND THE 8 WAVE COULTERS ON THE REAR KEEP HUBS POINTING OUTWARD. BEGIN IN CENTER OF MACHINE Page 67

68 A B Set tine rake angle A Roller Spring Adjuster. Bolt on center frame B ft RTS & RTS XT Assembly and Parts Manual 20" BLADES: USE SLOT (A) 17" BLADES: USE NEXT HOLE DOWN(B) 36ft Harrow Layout 36FT RTS HARROW LAYOUT 22" 1" 2-3" 1" 1" 2-3" 1" 32" 21" 44" 21" 39 1/2" 40 1/4" 39 1/2" 39 1/2" 40 1/4" 39 1/2" 32" 12 1/2" 12 1/2" 6 TINES R636 5 TINES R635 5 TINES R635 6 TINES R636 4'0" ROLLER MR80144R 5'0" ROLLER MR80145R 6'2" ROLLER MR80146R 5'0" ROLLER MR80145R 6'2" ROLLER MR80146R 5'0" ROLLER MR80145R 4'0" ROLLER MR80144R Page

69 41ft Coulter Layout SALFORD 41ft RTS /2" 40 1/2" 37" 37" 40 1/2" 56 1/2" 4 118" 21" 182" 21" 118" 11" 2 10" 18 1/2" 19 1/2" 19 1/2" 18 1/2" 12 1/2" 10" 2 11" 6" 12 1/2" 6" 6 1/2" 6" 4" 5 1/2" 4 1/2" 4 1/2" 5 1/2" 4 1/2" 4 1/2" 6 1/2" 4" 10" 12 1/2" 12 1/2" 26" 11 1/2" 10" 11 1/2" 26" 10" 3" 3" 14" 31" 3" 4 1/2" 7" 3" 10" 10" 14" 3" 4 1/2" 3" 7" 7" 7" 7" 7" 10" 21" 12 1/2" 31" 21" 21" 12 1/2" 21" LEGEND 100LBS WEIGHT KIT LAYOUT SHOWS MAXIMUM WEIGHTS ADDED (50LBS/FT) NON-SWIVELLING SPRING MOUNT 34 BLADES 36 BLADES 70 COULTERS 58 SWIVEL 12 RIGID NOTE: CENTER COILS MAY BE RH OR LH NON-SWIVEL SWIVEL USE HARDENED WASHERS LEAVE BOLT LOOSE TO ALLOW SWIVEL. IMPORTANT!! NOTE WHICH SIDE OF BEAM TO MOUNT THE COULTER FOR MACHINES WITH BOTH 13 & 8 WAVE COULTERS, INSTALL THE 13 WAVE COULTERS ON THE FRONT, AND THE 8 WAVE COULTERS ON THE REAR KEEP HUBS POINTING OUTWARD. BEGIN IN CENTER OF MACHINE 6" Page 69

70 41FT 570 RTS COULTER SPACING - DUAL AXLES /2" 40 1/2" 37" 37" 40 1/2" 118" 21" 182" 21" 11" 20" 2 10" 18 1/2" 19 1/2" 19 1/2" 18 1/2" 12 1/2" 6" 6 1/2" 12 1/2" 5 1/2" 4 1/2" 6" 4" 4 1/2" 4 1/2" 5 1/2" 6 1/2" 4 1/2" 10" 12 1/2" 12 1/2" 26" 11 1/2" 11 1/2" 10" 3" 3" 14" 31" 3" 4 1/2" 7" 3" 4 1/2" 10" 7" 7" 10" 31" 7" 12 1/2" 21" 21" 12 1/2" 21" LEGEND 100LBS WEIGHT KIT LAYOUT SHOWS MAXIMUM WEIGHTS ADDED (50LBS/FT) 34 BLADES NON-SWIVELLING SPRING MOUNT 36 BLADES NON-SWIVEL SWIVEL USE HARDENED WASHERS LEAVE BOLT LOOSE TO ALLOW SWIVEL. IMPORTANT!! NOTE WHICH SIDE OF BEAM TO MOUNT THE COULTER FOR MACHINES WITH BOTH 13 & 8 WAVE COULTERS, INSTALL THE 13 WAVE COULTERS ON THE FRONT, AND THE 8 WAVE COULTERS ON THE REAR 10" 10" 3" 56 1/2" 4 118" 2 20" 11" 6" 6" 4" 10" 26" 14" 3" 7" 7" 21" 70 COULTERS 60 SWIVEL 10 RIGID NOTE: CENTER COILS MAY BE RH OR LH KEEP HUBS POINTING OUTWARD. BEGIN IN CENTER OF MACHINE Page

71 41ft Harrow SALFORD Layout 41FT 3-SECTION RTS HARROW LAYOUT Set tine rake angle Roller Spring Adjuster. Bolt on center frame A B A B 20" BLADES: USE SLOT (A) 17" BLADES: USE NEXT HOLE DOWN(B) 22" 1" 2-3" 1" 1" 2-3" 1" 33 1/2" 21" 53" 40 1/4" 39 1/2" 21" 44" 21" 39 1/2" 40 1/4" 53" 21" 33 1/2" 3 TINES R633 4 TINES R634 5 TINES R635 6 TINES R636 4 TINES R634 3 TINES R633 5'0" ROLLER MR80145R 6'2" ROLLER MR80146R 6'2" ROLLER MR80146R 5'0" ROLLER MR80145R 6'2" ROLLER MR80146R 6'2" ROLLER MR80146R 5'0" ROLLER MR80145R Page 71

72 Hydraulics & Lights Wing Fold Hydraulics C B E D F Route hoses along frame clamps where provided. Base side GREEN (EXTEND) J Rod side GREEN-GREY (RETRACT) K G A 8B 7R H 9 10F 11 12F L H H L Page

73 27-30 Wing Fold Hydraulics FITTINGS LIST ITEM NO. QTY. PART NO. DESCRIPTION A 1 H SECTION WING FOLDING MANIFOLD B 1 A60079F HYDRAULIC MANIFOLD BRACKET C 2 B1025 5/8"-11NC x 2 1/2" HEX BOLT D 2 BN10L 5/8" NYLOCK NUT NC E 2 B0725 7/16" X 2 1/2" LG. GRADE 5 HEX BOLT F 2 BN07L 7/16" NYLOCK NUT NC G 8 H M ORB TO -06F NPT SWIVEL H 12 H ORB TO -06 NPT SWIVEL ELBOW J 1 HG-PT24E24R21R GREEN EXTEND/GREEN-GREY RETRACT HOSE GRIPS K 2 H80104P COUPLER 1/2" NPT MALE PIONEER L 4 HS /2" BORE X 24" STROKE HYD. CYLINDER HOSE LIST LABEL QTY LENGTH FROM TO 7R(Green-Grey) 1 20' Tractor Manifold 8B (Green-Green) 1 20' Tractor Manifold 9 2 1'10" Manifold Front Barrel 10F 2 4' Manifold Front Rod ' Manifold Rear Barrel 12F 2 10' Manifold Rear Rod CHARGING FOLD CYLINDERS Do not connect the cylinder rod until system has been charged with oil. 1. Prop up the cylinder with a block of wood (Fig 1). Check to see that the rod will extend completely without striking anything. 2. Connect tractor (note: check to see that all cylinders extend and retract in sync. If one goes backwards, check the plumbing.) 3. Extend cylinders completely, hold lever for 30 sec. as air exits cylinder. 4. Retract cylinder completely, hold lever for 30 sec. as air exits. 5. Repeat steps 3&4 three times. 6. Install cylinder pins. Be sure washers are installed correctly (see fold cylinder parts page). Air in the wing cylinder will cause wings to fall tothe ground!!! Whenever air could have entered the cylinders, repeat the process above to purge circuit. ALWAYS UNFOLD WINGS before working on hydraulics!!! Never work on a lift system with the wings folded Fig 1. When charging the circuit, prop up cylinder with block of wood. Be sure the rod can extend freely without striking anything Page 73

74 36-41 Wing Fold Hydraulics C B E Base side GREEN (EXTEND) J K Rod side GREEN-GREY (RETRACT) G A 8B 7R H D F 9 10F Route hoses along frame clamps where provided F L H H L Page

75 36-41 Wing Fold Hydraulics FITTINGS LIST ITEM NO. QTY. PART NO. DESCRIPTION A 1 H SECTION WING FOLDING MANIFOLD B 1 A60079F HYDRAULIC MANIFOLD BRACKET C 2 B1025 5/8"-11NC x 2 1/2" HEX BOLT D 2 BN10L 5/8" NYLOCK NUT NC E 2 B0725 7/16" X 2 1/2" LG. GRADE 5 HEX BOLT F 2 BN07L 7/16" NYLOCK NUT NC G 8 H M ORB TO -06F NPT SWIVEL H 12 H ORB TO -06 NPT SWIVEL ELBOW J 1 HG-PT24E24R21R GREEN EXTEND/GREEN-GREY RETRACT HOSE GRIPS K 2 H80104P COUPLER 1/2" NPT MALE PIONEER L 4 HS4036 4" BORE X 36" STROKE HYD. CYLINDER HOSE LIST LABEL QTY LENGTH FROM TO 7R (Green-Grey) 1 20' Tractor Manifold 8R (Green-Green) 1 20' Tractor Manifold 9 2 2'6" Manifold Front Barrel 10F 2 6'2" Manifold Front Rod '9" Manifold Rear Barrel 12F 2 11' Manifold Rear Rod CHARGING FOLD CYLINDERS Do not connect the cylinder rod until system has been charged with oil. 1. Prop up the cylinder with a block of wood (Fig 1). Check to see that the rod will extend completely without striking anything. 2. Connect tractor (note: check to see that all cylinders extend and retract in sync. If one goes backwards, check the plumbing.) 3. Extend cylinders completely, hold lever for 30 sec. as air exits cylinder. 4. Retract cylinder completely, hold lever for 30 sec. as air exits. 5. Repeat steps 3&4 three times. 6. Install cylinder pins. Be sure washers are installed correctly (see fold cylinder parts page). Air in the wing cylinder will cause wings to fall tothe ground!!! Whenever air could have entered the cylinders, repeat the process above to purge circuit. ALWAYS UNFOLD WINGS before working on hydraulics!!! Never work on a lift system with the wings folded Fig 1. When charging the circuit, prop up cylinder with block of wood. Be sure the rod can extend freely without striking anything Page 75

76 LIFTING Axle Lift HYDRAULICS Hydraulics D (TO TRACTOR) 1A F K E F G (RED-GREY) 1A 6 (TO TRACTOR) 1B F ROUTE HOSES THROUGH RINGS ON TONGE & TRIPOD (RED) 6 2 H 5 5 J F H A NOTE: TURN CYLINDERS SO THE PORTS FACE AWAY FROM THE REAR TIRE E F 2 1B 3 A A 3 3 C B B C ROUTE HOSES ALONG FRAME AND CLAMP WHERE PROVIDED LEAVE A SMALL DROOP OF HOSE OVER WING JOINTS. 5 # HARDWARE # HOSE Page

77 Axle Lift Hydraulics HOSE HARDWARE CHARGING THE CIRCUIT ATTENTION ON HARD GROUND, DO NOT RETRACT CYLINDERS ALL THE WAY WHILE THE TONGUE IS HITCHED TO TRACTOR - OR UNHOOK THE TURNBUCKLE FROM THE TONGUE TELESCOPE. OTHERWISE, THE TRACTOR DRAWBAR CAN BE BENT UPWARDS. Connect only the Barrel end of the cylinders until the circuit has been charged. 1. Be sure that all cylinders can extend completely without striking anything. Prop with blocks if necessary. 2. Connect Tractor. 3. Extend cylinders and hold lever for 2-3 minutes. This will purge the air from the circuit. (The lift cylinders have a port that allows oil to pass when completely extended.) 4. The circuit is now free from air. Install Rod end Pins. Connect tongue Turnbuckle Whenever air could have entered the cylinders, repeat above steps to purge circuit Identify the lift hose ends with red tie wraps for quick hookup to tractor. Route hoses behind axle towers Leave a small droop of hose (3-4") across wing joint Page 77

78 RTS MODELS: 27'- 41' (3 SEC) ft RTS & RTS XT Assembly and Parts Manual Light Installation 10 2 NOTE: RED MUST ALWAYS FACE THE REAR OF MACHINE MOUNTING BRACKET SHARES HARROW HEAD U-BOLT NOTE: USE STOVER LOCK NUTS WHEN MOUNTING LIGHT BRACKET TO HARROW HEAD Page

79 Light Installation ITEM NO. QTY. PART NO. DESCRIPTION 1 1 GL AA ORANGE LIGHT 2 1 GL R RED LIGHT 3 1 A60054 LIGHT BRACKET (LONG) 4 1 L00425 OUTSIDE LIGHT MOUNTING PLATE 5 8 BN04L 1/4" LOCK NUT 6 2 BU0410 1/4 x 1 1/2" U-BOLT 7 4 B0410 1/4" NC x 1 1/2" HEX BOLT 8 2 BN10S 5/8" NC STOVER LOCK NUT 9 1 C10726 SINGLE LIGHT BRACKET 10 1 B0812 1/2" x 1 1/4" HEX BOLT 11 1 BN08L 1/2" NYLOCK NUT NC NOTE: HAVE SOMEONE WATCHING FOR COLLISIONS WHEN FOLDING FOR THE FIRST TIME NOTE: LINE UP END OF BRACKET WITH OUTSIDE OF AMBER LIGHT THIS WILL PREVENT COLLISION WHILE FOLDING Page 79

80 Slow Moving Vehicle Sign and Rear Parking Stand NOTE: SMV and Parking Stand should be near center of machine, but careful not to hit Harrow Heads ITEM NO. QTY PART NUMBER DESCRIPTION 1 1 GAP103NS SMV SIGN 2 1 C1011 SMV MOUNTING BRACKET 3 3 BU1061 U-BOLT 5/8" x 6" x 5 1/2" 4 6 BN10L 5/8" NYLOCK NUT NC 5 2 BN06L 3/8"-16NC LOCK NUT 6 2 B0610 3/8" X 1" LG. GRADE C5507 REAR PARKING STAND MOUNT FOR 6" BEAM 8 1 C PARKING STAND 9 1 GP100414C03 5/8'' dia x 4 1/4'' pin RING & WASHER 10 1 GHP11 #11 HAIR PIN Page

81 Transport Lock Page 81

82 Grease Bank Tie strap along hydraulic hoses. F D F D 3-section (single-fold) frame E 5 D F F 2 D 2 F 3 E 4 5-section (double fold) frame The secondary wing hinges are greased. 1 (2 per center axle on 50ft) C 1 4 B 5 F E E 3 A C F Page

83 Grease Bank HOSES HOSE LABEL 18-30ft Machine 41ft Single fold Machine 41ft Double fold Machine 50ft Double fold Machine #1 6' 3" 6' 3" 4' 4' #2 12' 6" 17' 11' 12' 6" # ' 27' # ' 16' 6" # '6" 21' 6" KIT PART# KIT PART# KIT PART# KIT PART# H5724G H5740G H5741G H5750G 2006 and Prior H5724G and Prior H5740G and Prior H5741G-1 HARDWARE ITEM PART NO. DESCRIPTION A L00734 BRACKET FOR SINGLE FOLD B A60072 BRACKET FOR DOUBLE FOLD C BU1061 5/8 x 4 x 6" U-CLAMP D Coupling E /8" Elbow - 90 F /8" Elbow and Prior H5750G-1 Single-fold machine shown here Page 83