SALFORD TILLAGE 870 DISC ' & 35 MODELS 9" C-FLEX ASSEMBLY AND PARTS MANUAL SPECIALISTS. Подбор запасных частей на сайте:

Transcription

1 SALFORD TILLAGE SPECIALISTS Подбор запасных частей на сайте: DISC ' & 35 MODELS 9" C-FLEX ASSEMBLY AND PARTS MANUAL Лесных Павел Владимирович Тел ООО «ТехАгроПарк» Воронежская обл., Новоусманский р- н, п. Отрадное, ул. Автодорожная 7. (трасса М4 «Дон» 519 км пост ГАИ) Тел./факс 8 (473) info@texagropark36.ru

2 TABLE OF CONTENTS Recommended Torque Values..1 Frame assembly Mainframe Installation 2 Mainframe W-Tower Installation 3 Wing Installation.4 Tongue Installation.6 Self Leveling PVT Installation and Depth Control Rod.8 Lights and SMV Installation..10 Wheel and axle assembly 10,000 lb Main & Wing Disc Axle Assembly ,000 lb Tandem Axle (2 DOM).14 Mainframe Axle Installation..16 Wing Axle Mount Installation..18 Wing Axle Installation..20 Hydraulics Lift Hydraulics Wing Hydraulics...23 Disc Gangs Front Mainframe Assembly 24 C-Flex Hanger Assembly 26 2 ¼ Disc Gang Bearing Assembly 28 Wide Mainframe 9 Spacing 2 ¼ Shaft Layout..30 Disc Step Down Layout...31 Harrows 62 Long Harrow Arm Assembly 32 ½ Tine Harrow Assemblies Roller Harrow Assemblies...36 Wing Mounted Harrow Installation 38 Mainframe Mounted Harrow Installation..39 Harrow Layout.40 Optional Equipment Tow Hitch Assembly 41 Подбор запасных частей на сайте:

3 SALFORD RECOMMENDED TORQUE VALUES BOLT SIZE GRADE 2 GRADE 5 GRADE 8 ft-lbs Nm ft-lbs Nm ft-lbs Nm 1/2"NC /8"NC /4"NC /8"NC "NC NOTES: These recommended torque values are applicable when applied to the nut only. These recommended torque values are approximate only. The torque-tension relationship is affected by lubrication, surface finish, thread fit, plating, lock-washers, etc. DO NOT use these values if a different torque value or tightening procedure is given for a specific application. Torque values listed are for general use only. Check tightness of fasteners periodically. Shear bolts are designed to fail under predetermined loads. Always replace shear bolts with identical grade. Fasteners should be replaced with the same or higher grade. If higher-grade fasteners are used, these should only be tightened to the strength of the original. Make sure fasteners threads are clean and that you properly start thread engagement. This will prevent them from failing when tightening. WARNING Do not tighten one side of the u-bolt before the other side. Both sides of the u-bolt must be tightened equally Salford Farm Machinery Ltd. Page 1

4 3 4 ITEM NO. QTY. PART NO. DESCRIPTION 1 1 D70001A 870 DISC MAINFRAME - HEAVY AXLE INSTALLATION LH 2 1 D70001B 870 DISC MAINFRAME - HEAVY AXLE INSTALLATION RH 3 27 BN10S 5/8" NC STOVER LOCK NUT 4 54 BF10HS 5/8" HARD STRUCTURAL FLAT WASHER 5 27 B1025 5/8 x 2 1/2" HEX BOLT GR DO NOT INSERT TOP BOLTS AT THIS TIME ' Disc Assembly and Parts Manual MAINFRAME INSTALLATION Page 2 Salford Farm Machinery Ltd

5 MAINFRAME W-TOWER INSTALLATION ' DISC IMPORTANT WHEN FOLDING FOR THE FIRST TIME BOLT MUST BE ALL THE WAY IN, AFTER; SET BOLT SO CYLINDER WILL NOT BE UNDER PRESSURE IN TRANSPORT POSITION THEN TIGHTEN JAM NUT. ITEM NO. QTY. PART NO. DESCRIPTION 4 30 BN10S 5/8" NC STOVER LOCK NUT 5 60 BF10HS 5/8" HARD STRUCTURAL FLAT WASHER 6 1 D FRONT WIDE W-TOWER W/WING REST 7 1 D70106 REAR W-TOWER 8 1 D10049 W-TOWER TO SPIDER BRACE 9 1 GP A05 PIN 1" DIA. x 5 1/2" LG. - 2 HOLES 10 2 BF16 1" FLAT WASHER 11 2 BSC0415 1/4" x 1 1/2" COTTER PIN 12 1 D70112 SELF-LEVELING CYLINDER MOUNT BU1046 U-BOLT 5/8" x 4" x 7 1/2" LG BN10L 5/8" NYLOCK NUT NC 15 4 BN16J 1"NC JAM NUT 16 4 B1630 1" NC x 3" HEX BOLT GR.5 PLATED 17 3 B1035 5/8 x 3 1/2" HEX BOLT 18 8 B1080 5/8 x 8" HEX BOLT GR. 5 PLATED 19 2 D10016 DISC WRENCH Подбор запасных частей на сайте: Salford Farm Machinery Ltd. Page 3

6 WING INSTALLATION LH 35' WING INSTALLATION 7 FRONT NOTE: WINGLOCKS MUST BE TOWARD THE INSIDE AND TO THE FRONT OF MACHINE. RH 35' WING INSTALLATION Page 4 Salford Farm Machinery Ltd

7 870 35' WING INSTALLATION ITEM NO. QTY. PART NO. DESCRIPTION 1 9 BN08L 1/2" NYLOCK NUT NC 2 9 B0830 1/2" x 3" HEX BOLT 3 4 GP A09 1 1/2" DIA. x 10 1/2" LG B1070 5/8 x 7" HEX BOLT GR BN10L 5/8" NYLOCK NUT NC 6 64 BF10HS 5/8" HARD STRUCTURAL FLAT WASHER 7 8 L X 4 X 8" PULL-UP PLATE 8 4 D WING HINGE in. WIDE WING LEFT ' LH WING WELDMENT in. WIDE WING RIGHT ' RH WING WELDMENT 1. Install wing hinges (8) by aligning holes with holes on the mainframe, insert 1 1/2" x 10 1/2" pin (3) and retain with 1/2" x 3" hex bolt (2) and 1/2" nylock nut (1), once all pins and bolts are installed on hinges to mainframe, lift up wing hinges by setting a block underneath to make hinges parallel to mainframe. 2. Place wings at hinges making sure that the right hinges are on the right side and the left on the left, insert 5/8" x 7" hex bolts (4) with 5/8" hard structural flat washer (6) into pull-up plates (7) and align with holes on wing hinges and retain with 5/8" nylock nuts (5) and hard structural flat washers (6), NOTE: BEFORE TIGHTENING BOLTS ENSURE WINGS ARE PARALLEL WITH MAINFRAME AND FRONT OF WING LINES UP WITH FRONT OF MAINFRAME. Подбор запасных частей на сайте: Salford Farm Machinery Ltd. Page 5

8 TONGUE INSTALLATION Подбор запасных частей на сайте: Page 6 Salford Farm Machinery Ltd

9 TONGUE INSTALLATION ITEM NO. QTY. PART NO. DESCRIPTION 1 1 P9701C CAST CLEVIS TONGUE 2 1 A INNER TELESCOPE 3 1 A60040 OUTER TELESCOPE 48" 4 1 A50010 TURNBUCKLE 5 1 C TIP HOSE HOLDER 6 1 PPI-42XL CAT 4 CAST IRON HITCH 7 1 GJ LB TONGUE JACK 8 1 GJ ,000 LB SAFETY CHAIN 9 2 B1680H 1" x 8" NC HEX BOLT GR BN16L 1-8 NC NYLOCK NUT 11 1 GP A05 PIN 1" DIA. x 5 1/2" LG. - 2 HOLES 12 2 BF16S 1" SAE WASHER 13 2 BSC0515 5/16" x 1 1/2" COTTER PIN 14 2 GP H04 PIN 1" DIA. x 2 5/8" LG. WITH HEAD 15 4 BSC0415 1/4" x 1 1/2" COTTER PIN 16 1 GP10004L03 L-PIN 5/8" DIA. x 4" LG GHP11 #11 HAIR PIN 18 1 BU0830 1/2" x 3" x 4 1/2" U-BOLT 19 8 BN08L 1/2" NYLOCK NUT NC 20 1 GF641 1/4"-28NF GREASE FITTING 21 1 BN05L 5/16" LOCK NUT 22 4 B0830 1/2"NC x 3" HEX BOLT 23 1 B0520 5/16"NC x 2" BOLT 24 2 GP A09 PIN 1 1/2" DIA. x 7 5/8" LG. - 2 HOLES 25 1 GP B05 PIN 1" DIA. x 6 1/4" LG - 1 HOLE 1. Attach tongue (1) to frame assembly using 1 1/2" x 7 5/8" pins (24). Retain pins with 1/2" x 3" hex bolts (23) and 1/2" locknuts (8). 2. Insert inner telescope (2) into outer telescope (3). Attach turnbuckle (4) to telescope with 1" x 2 5/8" head pins (14) and 1/4" x 1 1/2" cotter pins (15). Install grease fitting (20) in end of outer telescope. 3. Attach top of telescope assembly to self-levelling assembly with 1" x 6 1/4" pin (25). Retain pin with 5/16" x 2" hex bolt (23) and 5/16" locknut (21). 4. Attach bottom of telescope assembly and safety chain (8) to tongue with 1" x 7 5/8" pin (24), 1" SAE washers (12), and 5/16" x 1 1/2" cotter pins (13). Note: pin goes through chain link in centre of tube. Washers go between plate and cotter pin. 5. Install hitch clevis (6) in end of tongue with 1" x 8" Grade 8 hex bolts (9) and 1" lock nuts (10). Insert bolts from opposite sides as shown. Add 1" washers between hitch and mounting plates if any play or clearance exists. 6. Install jack (7) onto tongue with 5/8" x 4" L-pin (16) and #11 hairpin (17). 7. Install hose holder (5) onto telescope approximately 16" from the end of the telescope. Retain hose holder with 1/2" x 3" x 4 1/2" u-bolt (18) and 1/2" locknuts (19) Salford Farm Machinery Ltd. Page 7

10 SELF LEVELLING PIVOT INSTALLATION ITEM NO. QTY. PART NO. DESCRIPTION 1 1 D70111 SELF-LEVELING PIVOT 2 2 HSR4012 4" BORE x 12" STROKE HYD. CYLINDER 3 2 GP H04 PIN 1" DIA. x 3 1/4" LG. WITH HEAD 4 1 GP A09 PIN 1 1/2" DIA. x 15 1/4" LG. - 2 HOLES 5 1 GP A05 1 1/4" DIA. x 10 1/4" LG - 2 HOLE 6 2 BN08L 1/2" NYLOCK NUT NC 7 2 B0830 1/2" x 3" HEX BOLT 8 2 GM30 1 1/4" MACHINE BUSHING 9 4 BSC0415 1/4" x 1 1/2" COTTER PIN 10 2 BSC0520 5/16" x 2" COTTER PIN Подбор запасных частей на сайте: Page 8 Salford Farm Machinery Ltd

11 DEPTH CONTROL ROD INSTALLATION ITEM NO. QTY. PART NO. DESCRIPTION 25 1 C1008 DETENT ADJUSTABLE STOP 26 1 C " DEPTH CONTROL ROD W/WELDED RING 27 1 D10011A POPPET VALVE BRACKET 28 1 BU1046 U-BOLT 5/8" x 4" x 7 1/2" LG HPMSC10 STROKE CONTROL VALVE 30 2 B0525 5/16"NC x 2 1/2" HEX BOLT 31 2 BN05L 5/16" LOCK NUT Boss must face mounting bracket Salford Farm Machinery Ltd. Page 9

12 ' Disc Assembly and Parts Manual LIGHTS AND SMV INSTALLATION Page 10 Salford Farm Machinery Ltd

13 870 LIGHTS AND SMV INSTALLATION ITEM NO. QTY. PART NO. DESCRIPTION 3 3 BU1061 U-BOLT 5/8" x 6" x 5 1/2" 4 6 BN10L 5/8" NYLOCK NUT NC 5 8 B0410 1/4" NC x 1 1/2" HEX BOLT 6 16 BN04L 1/4" LOCK NUT 7 1 C1011 SMV MOUNTING BRACKET 8 1 GAP103NS SMV SIGN 9 2 BN06L 3/8"-16NC LOCK NUT 10 2 B0610 3/8 X 1" PLATED BOLT GR A60055 LIGHT BRACKET (SHORT) 12 2 L00425 OUTSIDE LIGHT MOUNTING PLATE 13 2 GL AA ORANGE LIGHT 14 2 GL R RED LIGHT 15 4 BU0415 1/4 x 1 1/2" U-BOLT Подбор запасных частей на сайте: Salford Farm Machinery Ltd. Page 11

14 10000 LB WING DISC AXLE ASSEMBLY ITEM NO. QTY. PART NO. DESCRIPTION 1 1 C00083L LB UPRIGHT BEAM - LH 2 1 C00083R LB UPRIGHT BEAM - RH 3 1 C00084L LB DISC AXLE WALKING BEAM WLDMNT - LH 4 1 C00084R LB DISC AXLE WALKING BEAM WLDMNT - RH 5 2 GB LB CONE, LB INNER CONE 6 2 GB LB CUP, LB INNER CUP 7 2 GB LB OUTER CUP 8 2 GB LB OUTER CONE 9 2 BF20HS 1 1/4" HARD STRUCTURAL WASHER 10 2 BN20SF 1 1/4"NF SLOTTED HEX NUT 11 2 BSC0425 1/4" x 2 1/2" COTTER PIN 12 2 GW ,000 LB DUST CAP 13 3 GW8000A 8000 lb GREASABLE HUB AND 14" SPINDLE ASSY 14 3 B1045 5/8 x 4-1/2" BOLT 15 3 BN10L 5/8" NYLOCK NUT NC 16 2 GF1610 1/8" NPT GREASE FITTING 17 4 GBB /4" x 1 1/2" x 2" LG. HARD BUSHING 18 2 GW12110VC 10000/12000 LB COUNTERFACE 19 2 GW12110VS 10000/12000 LB V-SEAL 20 2 GW12110VW 10000/12000 LB GRASS WRAP GUARD FRONT LH AXLE ASSEMBLY RH AXLE ASSEMBLY Page 12 Salford Farm Machinery Ltd

15 LB WING DISC AXLE ASSEMBLY LH RH LH RH LEFT HAND ASSEMBLY SHOWN Salford Farm Machinery Ltd. Page 13

16 16000 LB TANDEM AXLE ASSEMBLY (2" DOM) ITEM NO. QTY. PART NO. DESCRIPTION 1 1 C00089L LB 870 DISC MAIN AXLE UPRIGHT LH 2 1 C00089R LB 870 DISC MAIN AXLE UPRIGHT RH 3 1 C00090L LB 870 DISC MAIN AXLE WALKER LH 4 1 C00090R LB 870 DISC MAIN AXLE WALKER RH 5 1 GB LB INNER CUP 6 1 GB LB OUTER CUP 7 1 GW LB DUST CAP 8 1 GW LB GREASE SEAL 9 1 GB LB INNER CONE 10 1 GB LB OUTER CONE 11 1 BN28SF 1 3/4" NF SLOTTED FLANGE NUT 12 1 BSR0527 5/16" x 2 3/4" ROLL PIN 13 4 B0505 5/16"NC x 1/2" LG. HEX BOLT 14 2 GW12000A LB HUB AND 15" SPINDLE ASSEMBLY 15 2 B1055H 5/8 x 5 1/2" HEX BOLT GR BN10L 5/8" NYLOCK NUT NC 17 3 GF1610 1/8" NPT GREASE FITTING FRONT 16" CENTRES LH AXLE ASSEMBLY RH AXLE ASSEMBLY Page 14 Salford Farm Machinery Ltd

17 LB TANDEM AXLE ASSEMBLY (2" DOM) LH RH LH RH LEFT HAND ASSEMLY SHOWN Salford Farm Machinery Ltd. Page 15

18 870 MAINFRAME AXLE INSTALLATION LEFT HAND AXLE SHOWN USE SAME METHOD FOR RIGHT HAND AXLE Подбор зарасных частей на сайте: Page 16 Salford Farm Machinery Ltd

19 870 MAINFRAME AXLE INSTALLATION ITEM NO. QTY. PART NO. DESCRIPTION 1 1 D70001A 870 DISC MAINFRAME - HEAVY AXLE INSTALLATION LH 2 1 C50010 TRANSPORT LOCK ASSEMBLY 3 2 BF16 1" FLAT WASHER 4 2 BSC0415 1/4" x 1 1/2" COTTER PIN 5 1 GP16005A05 PIN 1" DIA. x 5" LG. - 2 HOLES 6 1 GP H04 PIN 1" DIA. x 2 1/2" LG. WITH HEAD 7 2 BSC0315 3/16" x 1 1/2" COTTER PIN 8 1 C00091L LB 870 DISC MAIN AXLE ASSEMBLY LH 9 1 GP B11 2" x 19" LG 1-HOLE PIN 10 2 GW L x 15FL x 8 BOLT WHEEL & TIRE (12 PLY HIGHWAY) 11 1 HSR4508H 4 1/2" BORE x 8" STROK HYD. CYLINDER 12 1 GP H04 PIN 1" DIA. x 3 1/2" LG. WITH HEAD 13 1 B1040 5/8 x 4" HEX BOLT GR BN10 5/8" NC HEX NUT GR B0815 1/2" x 1 1/2" HEX BOLT 16 1 GPH F 1 1/4" x 7 3/4" LG. AXLE PIN - HARDENED 17 1 BL08 1/2" SPRING WASHER 18 2 GBB /2" x 1 1/4" x 1" LG. HARD BUSHING Salford Farm Machinery Ltd. Page 17

20 870 WING AXLE MOUNT INSTALLATION LH WING AXLE MOUNT INSTALLATION RH WING AXLE MOUNT INSTALLATION Page 18 Salford Farm Machinery Ltd

21 870 AXLE MOUNT INSTALLATION ITEM NO. QTY. PART NO. DESCRIPTION 4 20 BN10L 5/8" NYLOCK NUT NC in. WIDE WING LEFT 870 NARROW WING FRAME LEFT in. WIDE WING RIGHT 870 NARROW WING FRAME RIGHT 14 1 D70032 WIDE AXLE HANGER, WING RH 15 1 D70005 WIDE AXLE HANGER FOR WING LH BU1046 U-BOLT 5/8" x 4" x 7 1/2" LG D10019R RH WING AXLE ADJUSTER 18 1 D10019L LH WING AXLE ADJUSTER 19 4 BF20 1 1/4" FLAT WASHER 20 4 BN24 1 1/4" HEX NUT PLATED 21 2 BN20J 1 1/4" HEX JAM NUT GR.5 PLATED Salford Farm Machinery Ltd. Page 19

22 870 WING AXLE INSTALLATION LEFT HAND AXLE SHOWN USE SAME METHOD FOR RIGHT HAND AXLE Page 20 Salford Farm Machinery Ltd

23 870 WING AXLE INSTALLATION ITEM NO. QTY. PART NO. DESCRIPTION 7 1 GP B09 1 1/2" X 12 1/2" LG. 1 HOLE PIN 8 2 GP H04 PIN 1" DIA. x 3 1/2" LG. WITH HEAD 9 1 B0830 1/2" x 3" HEX BOLT 10 1 BN08 1/2" HEX NUT NC 11 2 BSC0415 1/4" x 1 1/2" COTTER PIN Salford Farm Machinery Ltd. Page 21

24 LIFT AXLE HYDRAULICS Page 22 Salford Farm Machinery Ltd

25 Salford Farm Machinery Ltd. Page 23

26 9" SPACING DISC GANG DISC GANG ASSEMBLY LEFT FRONT MAINFRAME SHOWN x 1 1/2" SPACER (8) USED FOR 9" SPACING 6 9 LEFT HAND ASSEMBLY SHOWN DISC WRENCH HAVE SOMEONE USE A DISC WRENCH ON 1 OF THE SQUARE NUTS (4), WHILE YOU TIGHTEN THE OTHER SQUARE NUT (4), THIS WILL ALLOW YOU TO TIGHTEN EACH NUT EASIER ' Disc Assembly and Parts Manual Page 24 Salford Farm Machinery Ltd

27 DISC GANG ASSEMBLY - LEFT FRONT MAINFRAME 9" SPACING ITEM NO. QTY. PART NO. DESCRIPTION 1 1 DK /4" DIA. DISC SHAFT 98 1/2" LG 2 8 D20020 SPOOL 9" x 6" DIA 3 11 CT " SMOOTH C.B. 6.5 MM (2.25" ROUND) 675 RAD. 4 2 D /4" SLOTTED SQUARE NUT 5 4 D " x 1 1/2" CONVEX WASHER 6 4 D " x 1 1/2" CONCAVE WASHER 7 3 D10040A 2 1/4" TRUNNION BEARING CARTRIDGE ASSEMBLY 8 3 D /2" x 1 1/2" FLAT SPACER 9 3 D00023B C-FLEX HANGER W/ BEARING RH 10 1 U TUBE 4" x 6" x 1/4"W x 90" LG U TUBE 2" x 2" x 3/16"W x 96" LG D10042 C-FLEX SCRAPER HANGER D10018 SCRAPER BLADE (RIGHT AND LEFT) BN08L 1/2" NYLOCK NUT NC BN10L 5/8" NYLOCK NUT NC BU0820 1/2" x 2 x 3 U-BOLT 17 3 BU1020 5/8" x 2 x 3 1/2" U-BOLT 18 3 BU1061 U-BOLT 5/8" x 6" x 5 1/2" BF10HS 5/8" HARD STRUCTURAL FLAT WASHER BF08HS 1/2" HARD STRUCTURAL FLAT WASHER Salford Farm Machinery Ltd. Page 25

28 C-FLEX HANGER ASSEMBLY Tighten this bolt to approx. 600 ft/lbs Use thread locker Then install Bolt locking plate (13) For 1 1/2" disc shafts 10 9 For 2 1/4" disc shafts Page 26 Salford Farm Machinery Ltd

29 C-FLEX HANGER ASSEMBLY ITEM NO. QTY. PART NO. DESCRIPTION 1 1 D /4" C-FLEX BEARING HANGER 2 1 D /4" C-FLEX SPRING 3 1 L " x 5" x 9" PLATE 4 2 B1285 3/4" NC X 8" HEX BOLT GR.5 PLATED 5 2 B1230 3/4" x 2" HEX BOLT GR.5 PLATED 6 5 BF12HS 3/4" HARD STRUCTURAL WASHER 7 5 BN12S 3/4" STOVER LOCK NUT 8 1 D /4" C-FLEX PULL-UP PLATE WITH STOPPER 9 1 D10040A 2 1/4" TRUNNION BEARING CARTRIDGE ASSEMBLY 10 1 D /2" DISC TRUNNION BEARING ASSEMBLY 11 2 GBB /2" x 1 1/4" x 1" LG. HARD BUSHING 12 1 B1275 3/4 x 9" HEX BOLT 13 2 D10054 GANG HANGER PIVOT BOLT 14 2 FL00156 BOLT LOCKING PLATE 15 2 B0825 1/2" x 2 1/2" HEX BOLT 16 2 BN08L 1/2" NYLOCK NUT NC RH hanger assembly LH hanger assembly The same parts can be assembled for LH or RH hangers Salford Farm Machinery Ltd. Page 27

30 /4" DISC GANG C-FLEX HANGER BEARING ASSEMBLY ' Disc Assembly and Parts Manual Page 28 Salford Farm Machinery Ltd

31 2 1/4" DISC GANG C-FLEX HANGER BEARING ASSEMBLY ITEM NO. QTY. PART NO. DESCRIPTION 1 1 D10027 BEARING HOUSING WITH STUBS WELDED 2 2 GB /4" DISC BEARING 3 1 D00039 CENTRE SPACER 4 1 D /4 BEARING CENTRE SLEEVE 5 2 D /2" BEARING SLEEVE END CAPS 6 2 GBS /4" DISC BEARING RUBBER SEAL 7 2 GBS39961U 2 1/4" DISC BEARING URETHANE WIPER Salford Farm Machinery Ltd. Page 29

32 DISC GANG LAYOUT ' WIDE MAINFRAME 9" SPACING 2 1/4" SHAFT SHAFT 116 1/2" SHAFT 98 1/2" SHAFT 98 1/2" 109" GANG TUBE 90" GANG TUBE 90" GANG TUBE 115" SCRAPER TUBE 10 1/2" 96" SCRAPER TUBE 96" SCRAPER TUBE 126" GANG TUBE 10 1/2" 84" GANG TUBE 84" GANG TUBE 10 1/2" 80" SCRAPER TUBE 80" SCRAPER TUBE 132" SCRAPER TUBE SHAFT 134 1/2" SHAFT 80 1/2" SHAFT 80 1/2" 94 BLADES + 2 FURROW FILLERS 10 1/2" SHAFT 116 1/2" 109" GANG TUBE 115" SCRAPER TUBE 126" GANG TUBE 132" SCRAPER TUBE SHAFT 134 1/2" Page 30 Salford Farm Machinery Ltd

33 2 1 4 DISC STEP DOWN LAYOUT 9" SPACING ' DISC LAYOUT SHOWN ITEM # DISC SIZE/PART # & BEARING # # OF PARTS PER SIZE OF 9" SPACING 21' 6" 24' 8" 26' 29' 31' 8" 35' CT CT CT D10045 BEARING CARTRIDGE Salford Farm Machinery Ltd. Page 31

34 62 INCH LONG HARROW ARM ASSEMBLY (5/8" PIVOT BOLT) On flat-fold wing-mounted arm assemblies only 17 Only use here when (13) is not required FLIP SPACER OVER TO LOWER TRANSPORT HEIGHT STANDARD POSITION AS SHOWN. NOTE: ON SOME MODELS (26) IS USED 26 OFFSET BLOCK TO ADJUST TRANSPORT HEIGHT Note: Tines shown with pin in bottom hole ' Disc Assembly and Parts Manual Page 32 Salford Farm Machinery Ltd

35 62 INCH LONG HARROW ARM ASSEMBLY (5/8" PIVOT BOLT) ITEM NO. QTY. PART NO. DESCRIPTION 1 1 R30012 PARALLEL LINKAGE BAR 2 1 R30006 PARALLEL LINKAGE ARM 3 1 R80099 HEAD,SALFORD HARROW FOR 5/8" UPPER PIVOT BOLT 4 1 R " HARROW ARM FOR 5/8" PIVOT AND U-BOLTS 5 1 R80100A 62" HARROW ARM W/ KIT (REPLACES RB1125) 6 5 BC0835H 1/2" X 13NC X 3-1/2" LG. CARRIAGE BOLT GR R0030 NYLON BUSHING 3/4" OD x 1/2" ID x 1.94 LG. 8 5 BN08L 1/2" NYLOCK NUT NC 9 6 BN10L 5/8" NYLOCK NUT NC 10 1 GP L03 1/2" x 3 1/2" PARKING STAND PIN 11 1 GHP11 #11 HAIR PIN 12 2 R0035 2" x 10" HARROW ARM SPRING 13 1 R80032 FLAT-FOLD ROLLER ARM STOP BRACKET 14 1 R80037L TINE SECTION UPRIGHT PLATE LEFT 15 1 R80037R TINE SECTION UPRIGHT PLATE RIGHT 16 1 R0028 STEEL HEAD SPACER 2 1/8" LG B1037ST 5/8" - 11NC X 3 3/4" SHORT THREAD BOLT 18 1 R /8"OD NYLATRON BUSHING 19 1 R /8"OD "ID NYLATRON ROD 20 1 R80096 HARROW ARM SPACER 21 2 RB0021 TIGHTENER,SINGLE SPRING 22 2 B0615 3/8" X 1 1/2" LG. GRADE BN06L 3/8"-16NC LOCK NUT 24 2 GHP9 #9 HAIR PIN 25 2 BU1020 5/8" x 2 x 3 1/2" U-BOLT 26 1 R80035 SPACER BLOCK 27 1 B1045 5/8 x 4 1/2" HEX BOLT GR 5 NOTES: + PLEASE NOTE- R80100 (62" HARROW ARM) IS ALSO AVAILABLE AS R80100A (THIS PART# INCLUDES (19) FOR 1/2" & (18) FOR 5/8" PIVOT BOLT AS WELL AS NEW 5/8" U-BOLTS) AND REPLACES PART# RB1125 (FOR 1/2" NYLON BUSHING AND U-BOLTS). + + SOME MODELS MAY USE (26) INSTEAD OF (20) ONLY USE (27) IF (13) IS NEEDED FOR DOUBLE FOLDED WINGS Salford Farm Machinery Ltd. Page 33

36 FOR ENDS OF FRONT TUBE ONLY OPTIONAL SECOND TUBE FOR WEIGHT TINE ANGLE ADJUSTER SHOWN HERE ON INNER LEFT. SEE HARROW LAYOUT FOR MACHINE SPECIFIC POSITIONS FOR ADJUSTOR MOUNTS ONLY ALL OTHER POSITIONS ' Disc Assembly and Parts Manual Page 34 Salford Farm Machinery Ltd

37 1/2" - 3 TINE HARROW ASSEMBLY PART NO. R633 ITEM NO. PART NO. DESCRIPTION 1 U TUBE 2 1/2 x 2 1/2 x 3/16"W x 54" LG. 2 R6063 TINE PIPE FOR 1/2" (3-TINE) 1/2" - 4 TINE HARROW ASSEMBLY PART NO. R634 ITEM NO. PART NO. DESCRIPTION 1 U TUBE 2 1/2 x 2 1/2 x 3/16"W x 72" LG. 2 R6064 TINE PIPE FOR 1/2" (4-TINE) 1/2" - 5 TINE HARROW ASSEMBLY PART NO. R635 ITEM NO. PART NO. DESCRIPTION 1 U TUBE 2 1/2 x 2 1/2 x 3/16"W x 92" LG. 2 R6065 TINE PIPE FOR 1/2" (5-TINE) 1/2" - 6 TINE HARROW ASSEMBLY PART NO. R636 ITEM NO. PART NO. DESCRIPTION 1 U TUBE 2 1/2 x 2 1/2 x 3/16"W x 112" LG. 2 R6066 TINE PIPE FOR 1/2" (6-TINE) COMMON PARTS ITEM NO. PART NO. DESCRIPTION 3 R /2" TINE TUBE CONNECTOR 4 R30011 CLAMP BRACKET 5 B0812 1/2 X 1 1/4" BOLT 6 BN08L 1/2" NYLOCK NUT NC 7 BU1025 U-BOLT 5/8" x 2 1/2" x 4" 8 BN10L 5/8" NYLOCK NUT NC 9 R /2" WIRE - 20" DBL LEG SPRING TINE 10 R30007 ADJUSTING BRACKET WELDMENT 11 R /2" TINE 3 BAR ADJUST CONNECTOR 12 R30010 ADJUSTING BAR HD 3 BAR TINE 13 R30008 ADJUSTING BRACKET HANDLE WELDMENT 14 R OD x.438 ID X 3/4 LONG SPACER 15 B0640 3/8"NC x 4" LG. HEX BOLT 16 BN06S 3/8"-16NC STOVER LOCK NUT 17 B0635 3/8"NC x 3 1/2" LG. HEX BOLT 18 R30015 LIGHT SAVER BRACKET 19 B0630 3/8"NC x 3" HEX BOLT 20 B0815 1/2" x 1 1/2" HEX BOLT 21 GHP11 #11 HAIR PIN Salford Farm Machinery Ltd. Page 35

38 ' Disc Assembly and Parts Manual Подбор запасных частей на сайте: Page 36 Salford Farm Machinery Ltd

39 Salford Farm Machinery Ltd. Page 37

40 WING MOUNTED HARROW INSTALLATION NOTE: USED ONLY WITH CERTAIN DISC MODELS Page 38 Salford Farm Machinery Ltd

41 WING MOUTED HARROW INSTALLATION ITEM NO. QTY. PART NO. DESCRIPTION 31 4 D /2" EXTENSION 32 2 U TUBE 4" x 6" x 1/4"W x 100" LG RB " HARROW ARM ASSEMBLY 34 2 R /2" TINE HARROW ASSY W/ OUTER RH HANDLE 37 4 MR1405R 5' ROLLER WITH FRAME RH 14" BU1061 5/8" x 6" x 5 1/2" U-BOLT BN10L 5/8" NYLOCK NUT NC BU0825 1/2" x 2 1/2" x 3 1/2" U-BOLT BU0820 1/2" x 2" x 3" U-BOLT BN08L 1/2" NYLOCK NUT NC MAINFRAME MOUNTED HARROW INSTALLATION (NO EXTENSIONS SEE LAYOUT) QTY. PART NO. DESCRIPTION 6 RB " HARROW ARM ASSEMBLY 2 R /2" TINE HARROW ASSY W/ OUTER RH HANDLE 3 MR1405R 5' ROLLER WITH FRAME RH 14" 12 BU1061 5/8" x 6" x 5 1/2" U-BOLT 24 BN10L 5/8" NYLOCK NUT NC 12 BU0825 1/2" x 2 1/2" x 3 1/2" U-BOLT 12 BU0820 1/2" x 2" x 3" U-BOLT 48 BN08L 1/2" NYLOCK NUT NC Подбор запасных частей на сайте: Salford Farm Machinery Ltd. Page 39

42 870-35' HARROW LAYOUT ' Disc Assembly and Parts Manual 5 TINES 26 3/4" 6 TINES SPACER MUST 30" BE 3" MIN. 35 3/4" 40" 35" 20" 9" 6 TINES 24 1/2" 5 TINES 9" 30" 15" 42" 40" 35 7/8" 18" TUBES ADDED FOR HARROW ARM HANGERS 100" 100" 5' RH 5' RH 5' RH 5' RH 5' RH 5' RH 5' RH Page 40 Salford Farm Machinery Ltd

43 870 TOW HITCH INSTALLATION ITEM NO. PART NUMBER DESCRIPTION QTY. 3 MD873 TOW HITCH WELDMENT DISC 1 4 BU1046 U-BOLT 5/8" x 4" x 7 1/2" LG. 6 5 BN10L 5/8" NYLOCK NUT NC Подбор запасных частей на сайте: Salford Farm Machinery Ltd. Page 41