SUPER CUB PARTS CATALOG CARD 1 OF 1

Transcription

1 Courtesy of Bomar Flying Service SUPER CUB PARTS CATALOG CARD OF PIPER AIRCRAFT CORPORATION (PART NUMBER Al

2 AEROFICHE EXPLANATION AND REVISION STATUS The parts catalog information in this set of Aerofiche cards is arranged in accordance with general specifications of Aerofiche adopted by the General Aviation Manufacturer's Association Conversion of Aerofiche alpha/numeric code numbers: First number is the Aerofiche card identifier Letter is the horizontal line reference per card Second number is the vertical line reference per card Example: J6 = Aerofiche card number two of given set, grid location J6 A Table of Contents is located at grid A8 REVISIONS The information in this Aerofiche Parts Catalog is kept current by revisions distributed periodically These revisions supersede all prevlous revisions, are complete Aerofiche card replacements, and supersede Aerofiche cards of the same number in the set Revisions to this PA-8-50 Super Cub Pans Catalog (76 83) issued June 7, 988 are as follows Effectivity Publication Date Aerofiche Card Effectivity ORG88067 August NOTE Consult the Customer Service Information Aerofiche for current revision dates for th~s manual ISSUED: JUNE

3 0 INTRODUCTION This illustrated parts catalog provides simple but positive identification of replacement parts for the Piper Super Cub PA manufactured by Piper Aircraft Corporation of Vero Beach, Florida Do not use this catalog for rigging or installation purposes The catalog is divided into eleven major sections as follows: a Sections I to X inclusive contain all replacement parts for the complete airplane Each section is subdivided and each division includes an illustration and a pans listing b Section XI is the Miscellaneous Group This group includes a listing of the Optional Equipment Kits The following is a brief explanation of the columns in the parts listing: a The FIGURE AND INDEX column indicates the illustration figure number and its pans index number Example: (-). the is the figure number and the is the index number. The figure number appears only at the top of each pans list~ng page or at the beginning of each new pans listing. b The PART NUMBER column contains the identifying number of the replacement part This number must be shown on all parts orders c The CODE column indicates special uses of the part An explanat~on of the letter code is shown on the CODE EXPLANATIONS Page d The NOMENCLATURE column indicates the pan name This name must be shown on all parts orders e The NO REQ column represents the total quantity of pans used per aircraft per figure when the part is not indented and t quantity of parts used per assembly when the part is indented The symbol AR listed in this column means "As Required" f The SERIAL NUMBERS AFFECTED column indicates the part application by airplane serial number Figure and Index Number Part Number Code EXAMPLE NOMENCLATURE N o. Req. SERIAL NUMBERS AFFECTED DOOR ASSEMBLY - Baggage compartment ' FRAME ASSEMBLY - Baggage compartment door ' ' HINGE ASSEMBLY - Baggage door CLIP - Baggage door spring This listing is interpreted as follows: If the DOOR ASSEMBLY (not indented) is ordered, it will include the three items listed under DOOR ASSEMBLY If the FRAME ASSEMBLY (indented one space) is ordered, it will include the two items listed under FRAME ASSEMBLY If you want only a HINGE ASSEMBLY or CLIP, you order only that item. 3 Optional equipment items are contained in the parts list in their proper sequence and sections These items are not marked optional. since they are fully identified by their descriptions ISSUED: JUNE 7, 988

4 HOW TO IDENTIFY A PART IF YOU KNOW WHAT IT LOOKS LIKE AND KNOW WHERE IT IS LOCATED Refer to Figure to determine the section number in which the pan is located Refer to the Table of Contents and locate the section Note the figure numbers that illustrate the various subgroups of this main section Select the figure title you think might contain the part you wish to identify and turn to the grid (page) specified 3 Find the part on the illustration and note the index number NOTE: If you don't find the part on this illustration, try another figure in this group 4 Refer to the "Figure and Index Number" in the parts listing for complete description of the part HOW TO ORDER PARTS When ordering parts, please observe the following instructions: Place your order with your local distributor or service center Specify the model and serial number of your airplane 3 Specify part number, name, type and quantity required 4 Specify the method of shipment - freight, express, parcel post. air express. air freight or air parcel post Where the natureof thesh~pment requires it or when no instructions are given, we reserve the right to ship the most suitable way 5 Request price and delivery information prior to order placement. GENERAL INFORMATION Shortages All orders are checked before leaving our shipping department A packing slip is enclosed with the shipment. Claims for errors or shortages must be made within three days after receipt of orders Retu~hed Goods Please do not return material to us without securing our written permission Material returned to us without notice will be held at theowner's risk for thirty days and will then be disposed of as we see fit NOTE: Transportation charges must be prepaid on returned goods or the shipment will be refused 3 Transportation Liabilities The Piper Aircraft Corporation cannot be held liable 'for damages to parts in transit from the factory If a shipment is received in a damaged condition, have the delivery man or transportation company make a notation of the damageand fileyour claim with thecarrier Incaseof concealed damage, do not attempt to remove the part from the shipping container, or try to repair the damage Call the carrier and have their claim agent inspect the damage before filing your claim with the carrier ISSUED: JUNE PA- 8-50

5 PA SERIAL NUMBER INFORMATION Serial numbers of the aircraft covered in this parts catalog are as follows: PA Super Cub serial numbers and up. ISSUED JUNE

6 CECONITE 7600 PROCESS FINISH MATERIALS - NOTE - The Piper PA-8-50 Super Cub is manufactured using the Blue River Ceconite 7600 Aircraft Covering Process All finish products listed below are used only in this process PIPER PART NUMBER Flexi-Gloss Finish. Cub Yellow....I (Gallon) Flexi-Gloss Finish, White....I (Gallon) Flexi-Gloss Finish. Black....I70 88 (Quart) Flexi-Gloss Finish, Clear....I70 88 (Gallon) Activator (7603GL)....I (Gallon) Activator (7603QT)....I (Quart) Cement (760GL)....I (Gallon) Cement (760QT)....I (Quart) Cleaner (CLl GL) (Gallon) Filler (760GL) (Gallon) Tape - Pinked, " wide (76P)....I (50 yard) Tape - Pinked, 3" wide (76P3)....I80 47 (5 yard) Tape - Pinked, 4" wide (76P4)....I80 47 (5 yard) Tape - Cloth. multi-purpose, " wide......la0 474 (60 feet) Tape - Reinforcing, /4" wide (RT4)....l8O 475 (60 yard) Tape - Reinforcing, /" wide (RT)....l (60 yard) ISSUED: JUNE

7 0 THIS PAGE INTENTIONALLY LEFT BLANK

8 TABLE OF CONTENTS FIGURE NUMBER FIGURE TITLE Ceconite 7600 Process Finish Materials... Exploded View of Complete Airplane... SECTION I WING GROUP GRID NUMBER Wing and Fuel Tank Installation... A Covered Wing Assembly... A6 Wing Panel Assembly. Uncovered (Showing Leading Edge)... A0 Wing Panel Assembly. Uncovered (Showing Trailing Edge)... A4 Flap Assembly... lb5 Aileron Assembly... lb8 Strut Installation... Bl SECTION I FUSELAGE GROUP Covered Fuselage Assembly. Left View Covered Fuselage Assembly. Right View Fuselage Frame Assembly... 8 Seats Installation... Cl Rudder Pedals and Floorboards Installation... C4 Throttle. Cabin and Carburetor Heat Mixture Controls... C7 Instrument Panel Installation (Standard)... ClO Instrument Panel Installation (With Options)... C4 SECTION Ill AGRICULTURAL GROUP SECTION IV TAIL GROUP Tail Surface Installation... lc8 SECTION V CHASSIS GROUP Landing Gear Installation... C Brake Assembly (Cleveland)... ID Main Wheel Assembly (Cleveland)... ID5 Tail Wheel Installation... ID8 Brake Installation... Dl SECTION VI POWERPLANT GROUP Powerplant Installation. Lycoming... Dl 4 Spinner Installation... Dl 9 Cowl Installation. Lycoming... ID Baffles Installation... El Vacuum System Installation... E4 ISSUED: JUNE

9 TABLE OF CONTENTS FIGURE NUMBER FIGURE TITLE GRID NUMBER Fuel System Installation... SECTION VII FUEL SYSTEM GROUP SECTION Vlll ELECTRICAL SYSTEM GROUP Electrical System Installation... El Electrical Components Installation... El 6 Wing Light and Strobe Light Installation... El 9 Landing Light Installation... E Electric Fuel Gauge Installation... IF Speaker and Dome Light Installation... F4 SECTION IX CONTROL SYSTEM GROUP Elevator and Aileron Control Installation... Elevator Control System... Aileron Control System... Rudder Control System... Flap Control System... Adjustment Stabilizer Control System... Stabilizer Adjustment Crank Installation... Stabilizer Adjustment Yoke and Bungee Installation... SECTION X RADIO GROUP Piper Automatic Locator (ELT) Installation (Narco Avionics)... SECTION XI MISCELLANEOUS GROUP Optional Equipment Kits... G8 G ISSUED: JUNE

10 a- PIPER PARTS CATALOG THIS PAGE INTENTIONALLY LEFT BLANK

11 a XI MISCELLANEOUS ISSUED: JUNE 7, 988 Figure Exploded View of Complete Airplane lall

12 a PIPER PARTS CATALOG ISSUED: JUNE 7, 988 Figure Wing and Fuel Tank Installation A

13 CODE EXPLANATIONS FOR FIGURE ISSUED: JUNE 7, 988

14 SECTION I Wing Group I Figure I I PIPER PARTS CATALOG Part Index and Number Code - NOMENCLATURE DRAWING - Rigging Diagram DRAWING - Wing and Fuel Tank Installation DRAWING - Aircraft Dimension and Control Surface Travel WING AND FUEL TANK INSTALLATION FAIRING - Wing Root. LH FAIRING - Wing Root. RH MOULDING - Rubber FAIRING - Wing Root, top FAIRING - Wing Root, bottom front. LH FAIRING - Wing Root, bottom front. RH FAIRING - Wing Root. bottom rear, LH FAIRING - Wing Root. bottom rear, RH PLATE - Fairing attachment. LH PLATE - Fairing attachment, RH PANEL ASSEMBLY - Wing, Ceconite covered, LH PANEL ASSEMBLY - Wing, Ceconite covered. RH ENVELOPE - Wing, Ceconite. left or right (BLU PA-8-W) BOLT - (AN5-7A) WASHER - (AN960-55) NUT - (MS C) BOLT - (AN5-6A) WASHER - (AN960-56) NUT - (MS C) FAIRING - Flap, LH FAIRING - Flap, RH FLAP ASSEMBLY - Aluminum, Left FLAP ASSEMBLY - Aluminum. Right HINGE - Flap, inboard HINGE - Flap, outboard AILERON ASSEMBLY - Aluminum. left AILERON ASSEMBLY - Aluminum, right HINGE - Center HINGE - Inboard and outboard HORN ASSEMBLY COVER - Pulley COVER ASSEMBLY - Fuel tank. LH COVER ASSEMBLY - Fuel tank, RH (reversed) FELT - Top (4-per ship) FELT - Bottom (4-per ship) FELT - Front (4-per ship) FELT - SAE F-50 tank cover (0 ft per ship) CAP - Tank (fuel cap assembly) STUD - Tank strap (4-per ship) TANK ASSEMBLY - Fuel, LH TANK ASSEMBLY - Fuel. RH FLANGE - Fuel tank filler cap HOSE, Flexible HOSE, Flexible HOSE, Flexible CLAMP. (#8 SAE Type "E" Zinc plated) CLAMP, (SAE TY F GS4SS) When ordering, always specify Part Number. Description, and Serial Number of Aircraft ISSUED: JUNE 7,988 A4

15 WING AND FUEL TANK INSTALLATION SECTION I When ordering. always specify Part Number, Description. and Serial Number of Aircraft ISSUED: JUNE 7,988 A5

16 Figure 3 Covered Wing Assembly ISSUED: JUNE 7, 988 A 6

17 CODE EXPLANATIONS FOR FIGURE 3 ISSUED: JUNE 7,988

18 When ordering, always specify Part Number, Description. and Serial Number of Aircraft ISSUED: JUNE A8

19 THIS PAGE INTENTIONALLY LEFT BLANK

20 a PIPER PARTS CATALOG Figure 4 Wing Panel Assembly, Uncovered (Showing Leading Edge) ISSUED: JUNE 7,988 A0

21 CODE EXPLANATIONS FOR FIGURE 4 ISSUED: JUNE 7,988

22 SECTION I WING PANEL ASSEMBLY, UNCOVERED Wing Group (Showlng Leadlng Edge) PIPER PARTS CATALOG Figure and Part No. SERIAL NUMBERS Index Number Code NOMENCLATURE Req. AFFECTED Number DRAWING - Wing panel assembly, uncovered WlNG PANEL ASSEMBLY - Uncovered LH WlNG PANEL ASSEMBLY - Uncovered RH LIGHT - Landing (4509) COVER - Leading edge inboard RH #I COVER - Leading edge inboard LH #I COVER - Leading edge center inboard section LH # COVER - Leading edge center inboard section RH # COVER - ~ eadin~ edge center outboard section LH #3 COVER - Leading edge center outboard section RH #3 COVER - Leading edge outboard #4 COVER - Tip, leading edge, LH COVER - Tip, leading edge, RH BOW - Wing tip FITTING - Wing tip bow rear spar FllTlNG - Wing tip bow rear spar FITTING - Wing tip bow front spar FllTlNG -Wing tip bow front spar FllTlNG - Front spar butt hinge BLOCK - Filler FllTlNG ASSEMBLY - Left strut attachment STRAP ASSEMBLY - Fuel tank STRAP ASSEMBLY - Fuel tank STRAP ASSEMBLY - Fuel tank TUBE - Drag brace, fuel tank FllTlNG - Hinge rear spar butt ROD - Push pull flap BEARING - Push pull rod BELLCRANK BRACKET - Flap bellcrank ANGLE - Reinforcement ANGLE - Reinforcement BRACKET ASSEMBLY - Flap hinge BRACKET ASSEMBLY - Flap hinge BLOCK - Bearing RIVET - Steel (/8" x 5/6" L) PLATE - Stop ANGLE - Reinforcement inboard aileron hinge, outboard aileron hinge. and outboard flap hinge BRACE ASSEMBLY - False spar BLOCK - Filler FIlTING - Lift strut attachment SPACER SPACER BRACKET ASSEMBLY - Aileron hinge BLOCK RIVET - Steel ( /8" x 5/6" L) STOP ASSEMBLY - Aileron BRACKET - Aileron pulley, inboard half. LH BRACKET - Aileron pulley, inboard half, RH BRACKET - Aileron pulley, outboard half. LH When ordering, always specify Part Number. Description, and Serial Number of Aircraft ISSUED: JUNE 7,988 A

23 WING PANEL ASSEMBLY, UNCOVERED (Showing Leading Edge) Figure and Index Number Part Number Code PIPER PARTS CATALOG NOMENCLATURE BRACKET - Aileron pulley, outboard half, RH BRACKET - Aileron pulley housing attachment BUSHING BRACKET ASSEMBLY - Door catch mounting ANGLE - Reinforcement. pulley bracket, LH ANGLE - Reinforcement, pulley bracket, RH ANGLE - Reinforcement, center aileron hinge, LH ANGLE - Reinforcement, center aileron hinge. RH ANGLE - Reinforcement. No drag strut ANGLE - Reinforcement, No drag strut ANGLE - Reinforcement. No drag strut ANGLE - Reinforcement, No 3 drag strut ANGLE - Reinforcement, No 3 drag strut ANGLE - Reinforcement, No 5 drag strut ANGLE - Reinforcement, No 5 drag strut HOUSING - Pulley BOLT - Flap bellcrank to push pull rod (AN3-A) CHANNEL - Reinforcement WASHER - Spacer, flap control rod installation at bellcrank (AN960-0) WASHER - Fuel tank strap attachment No. Req. 4 6 SERIAL NUMBERS AFFECTED SECTION I Wing Group When ordering. always specify Pan Number, Description, and Serial Number of Aircraft ISSUED: JUNE 7,988 A3

24 a PIPER PARTS CATALOG Figure 5 Wing Panel Assembly, Uncovered (Showing Trailing Edge) ISSUED: JUNE A4

25 CODE EXPLANATIONS FOR FIGURE 5 ISSUED: JUNE 7.988

26 SECTION I Wing Group Figuro and Index Number Part Number Code PIPER PARTS CATALOG NOMENCLATURE WING PANEL ASSEMBLY. UNCOVERED - - (Showing Trailing Edge) a No. SERIAL NUMBERS Req. AFFECTED DRAWING - Wing Panel Assembly, Uncovered I SPAR - False, flap inboard, left SPAR - False, flap inboard. right SPAR - False. flap outboard, left SPAR - False, flap outboard, right SPAR - False, aileron inboard, left SPAR - False, aileron inboard. right SPAR - False, aileron outboard, left SPAR - False, aileron outboard, right BRACE - Channel (8 5" L) BRACE - Channel ( 6 0" L) BRACE - Channel (6 5" L) STRUT - Drag, No WASHER BUSHING - Insert FITTING - Attachment, brace tube FITTING ASSEMBLY - Drag wire pull, rear spar. No drag strut 'WASHER - Square 'FITTING 'CLEVIS 'NIPPLE FllTING ASSEMBLY - Drag wire pull, front spar No drag strut 'WASHER - Square 'FITTING 'CLEVIS 'NIPPLE STRUT ASSEMBLY - Drag, No and No 3 FITTING ASSEMBLY - Drag wire pull, front and rear spar, No 3 drag strut 'WASHER - Square 'FITTING 'CLEVIS 'NIPPLE FlnlNG ASSEMBLY - Drag wire pull, "N" brace, front and rear spar, No 4 drag strut 'WASHER - Square 'NIPPLE 'CLEVIS 'FIlTlNG TUBE ASSEMBLY - Drag strut, upper "N" TUBE - Drag strut. "N" brace TUBE ASSEMBLY - Drag strut, lower "N" FITTING ASSEMBLY - Drag wire pull, front and rear spar, No 5 drag strut 'WASHER - Square 'FITTING - Wire pull 'CLEVIS 'NIPPLE WIRE - Drag. No and No 3 bay (44 875" L) WIRE - Drag. No 4 bay (56 5" L) ANGLE - Rear spar ANGLE - Front spar When ordering. always specify Pan Number. Description. and Serial Number of Aircraft : I I ISSUED: JUNE

27 WING PANEL ASSEMBLY, UNCOVERED (Showing Trailing Edge) Figure and Index Number Part Number Code PIPER PARTS CATALOG NOMENCLATURE FlTlNG - Front and rear spar. Jury strut BLOCK - Filler, rear spar BLOCK - Filler, front spar BRACKET - Airspeed. left BRACKET ASSEMBLY - Pulley CLIP - Navigation light wire FORMER - Fabric, "N" brace assembly, left FORMER - Fabric. "N" brace assembly, right BUSHING - Insert, pulley No. Req. 4 4 PLATE - Lock STRUT - Drag No. 5 BRACE - Channel (" L) : RIB ASSEMBLY - No butt. left RIB ASSEMBLY - No butt, right RIB ASSEMBLY - No and 3, left! RIB ASSEMBLY - No and 3, right RIB ASSEMBLY - No 4, left RIB ASSEMBLY - No 4, right RIB ASSEMBLY - No 5, left RIB ASSEMBLY - No 5, right RIB ASSEMBLY - No 6, left RIB ASSEMBLY - No 6. right RIB ASSEMBLY - No 7, left RIB ASSEMBLY - No 7, right RIB ASSEMBLY - No 8, left i I RIB ASSEMBLY - No 8, right RIB ASSEMBLY - No 9. left RIB ASSEMBLY - No 9, right RIB ASSEMBLY - No 0, left RIB ASSEMBLY - No 0, right RIB ASSEMBLY - No, left RIB ASSEMBLY - No, right RIB ASSEMBLY - No. left ' RIB ASSEMBLY - No, right RIB ASSEMBLY - No 3, left RIB ASSEMBLY - No 3, right RIB ASSEMBLY - No 4, left RIB ASSEMBLY - No 4, right RIB ASSEMBLY - No 5, left RIB ASSEMBLY - No. 5. right RIB ASSEMBLY - No 6, left tip RIB ASSEMBLY - No 6, right tip RIB - Nose, tip, left RIB - Nose, tip, right RIB ASSEMBLY - Nose, left and right RIB ASSEMBLY - Nose. No 6, left and right SPAR ASSEMBLY - Front, left SPAR ASSEMBLY - Front, right SPAR ASSEMBLY - Rear, left SPAR ASSEMBLY - Rear, right GUSSET - False spar PLATE - "U", fairlead retainer PLATE - Butt rib and leading edge attachment BRACE - Wing rib I! I ' 0 4 AR SERIAL NUMBERS AFFECTED SECTION I Wing Group When ordering, always specify Part Number, Description, and Serial Number of Aircraft ISSUED: JUNE 7,

28 0 THIS PAGE INTENTIONALLY LEFT BLANK

29 Figure 6 Flap Assembly ISSUED: JUNE 7,988 B5

30 CODE EXPLANATIONS FOR FIGURE 6 ISSUED: JUNE 7.988

31 SECTION I W~ng Group PIPER PARTS CATALOG Figure and Part Index Number Code NOMENCLATURE Number I I FLAP ASSEMBLY - Left FLAP ASSEMBLY - Right SPAR ASSEMBLY - Flap, left (complete) SPAR ASSEMBLY - Flap, rlght (complete) BULKHEAD - Flap, left BULKHEAD - Flap, right BULKHEAD - Flap, left BULKHEAD - Flap, right BULKHEAD - Flap, left BULKHEAD - Flap, right RIB - Flap RIB - Flap HINGE ASSEMBLY - Flap, inboard HINGE ASSEMBLY - Flap. outboard BULKHEAD - Flap, left BULKHEAD - Flap, right SKlN - Flap, leading edge SKlN - Flap, leading edge. inboard, left SKlN - Flap. leading edge, inboard, right SKlN - Flap. leading edge, outboard, left SKlN - Flap. leading edge, outboard, right SKlN - Flap. trailing edge, top, left SKlN - Flap. trailing edge. top, right SKlN - Flap, trailing edge, bottom, left SKlN - Flap. trailing edge, bottom right REINFORCEMENT - Trailing edge FLAP ASSEMBLY When ordering. always specify Part Number, Description, and Serial Number of Aircraft ISSUED: JUNE

32 a Figure 7 Aileron Assembly ISSUED: JUNE 7,

33 CODE EXPLANATIONS FOR FIGURE 7 ISSUED: JUNE 7,988

34 SECTION I Wing Group Figure and Index Number Part Number Code PIPER PARTS CATALOG NOMENCLATURE No. Req. AILERON ASSEMBLY SERIAL NUMBERS AFFECTED : i / ! , : i ! j , i ; , , , ! AILERON ASSEMBLY - Left AILERON ASSEMBLY - Right 'SPAR ASSEMBLY - Left (complete) 'SPAR ASSEMBLY - Right (complete) "BULKHEAD - Flap, left "BULKHEAD - Flap, right "BULKHEAD - Flap, left "BULKHEAD - Flap. right "RIB - Aileron "RIB - Aileron "RIB - Aileron "RIB - Aileron "HINGE ASSEMBLY - Aileron "HINGE ASSEMBLY - Aileron, center "HORN ASSEMBLY - Aileron 'BULKHEAD - Aileron, left 'BULKHEAD - Aileron, right 'SKIN - Aileron, inboard. left 'SKIN - Aileron, inboard, right 'SKIN - Aileron. center, inboard, left 'SKIN - Aileron, center, inboard, right 'SKIN - Aileron. center, outboard. left 'SKIN - Aileron, center. outboard, right 'SKIN - Aileron, outboard, left 'SKIN - Aileron. outboard. right 'SKIN - Aileron. trailing edge, inboard. top, left 'SKIN - Aileron. trailing edge, inboard. top, right 'SKIN - Aileron, trailing edge. inboard, bottom, left 'SKIN - Aileron, trailing edge, inboard, bottom, right 'SKIN - Aileron. trailing edge, outboard, top. left i 'SKIN - Aileron, trailing edge. outboard, top, right! 'SKIN - Aileron. trailing edge. outboard, bottom. left I 'SKIN - Aileron, trailing edge. outboard. bottom, right 'WEIGHT - Aileron balance i 'TAB - Aileron trim I 'REINFORCEMENT - Trailing edge I I I I I! I i I i I I i ISSUED: JUNE 7, 988 When ordering. always specify Part Number. Description. and Serial Number of Aircraft B0

35 Figure 8 Strut Installation ISSUED: JUNE

36 CODE EXPLANATIONS FOR FIGURE 8 ISSUED: JUNE 7, 988 PA- 8-50

37 SECTION I Wino Grouo - Figure and Part Index Number Numbel I Code I I PIPER PARTS CATALOG NOMENCLATURE DRAWING - Strut Installation. Lift and Jury STRUT INSTALLATION STRUT - Jury, front STRUT - Jury, rear BOLT - (AN3-4A) WASHER - (AN960-0) NUT - (Elastic Stop Nut No M0) TUBE - Jury strut spacer CLAMP ASSEMBLY - Front jury strut CLAMP - Rear jury strut RING - Snap, cable fairlead FAIRLEAD - Cable, segment CLAMP -Jury strut HOUSING ASSEMBLY - Pulley, LH HOUSING ASSEMBLY - Pulley. RH BRACKET ASSEMBLY - Tie down BUSHING - Spacer STRUT ASSEMBLY - Lift front 'FORK ASSEMBLY BOLT - Lift strut attachment NUT - (AN30-6) PIN - Cotter (AN30-6) STRUT ASSEMBLY - Rear lift 'FORK ASSEMBLY BOLT - (AN5-4A) WASHER - (AN960-56) NUT - (4EO54) BOLT - Lift strut attachment NUT - (AN30-6) PIN - Cotter (AN ) BOLT - (AN5-7A) NUT - (Elastic Stop Nut No 4E054) DECAL - No Step When order~ng, always specify Part Number. Description, and Serial Number of Aircraft ISSUED: JUNE B3 PA-8-50

38 Figure 9 Covered Fuselage Assembly. Left View ISSUED: JUNE 7,988 84

39 CODE EXPLANATIONS FOR FIGURE 9 ISSUED JUNE 7.988

40 SECTION I Fuselage Group PIPER PARTS CATALOG COVERED FUSELAGE ASSEMBLY Figure and Pert No. SERIAL NUMBERS Index Number Code NOMENCLATURE Req. AFFECTED Number DRAWING - Fuselage Assembly, Complete DRAWING - Fabric or Ceconite Installation, Fuselage / FUSELAGE ASSEMBLY - Ceconite covered (with seat and floor) 'ENVELOPE - Fuselage, Ceconite (BLU PA- 8-F) COVER - Inspection COVER - Inspection (battery drain access) COVER - Stabilizer yoke inspection. LH COVER - Stabilizer yoke inspection, RH PANEL - Tail inspection, LH PANEL - Tail inspection, RH COVER - Inspection. rectangular COWL ASSEMBLY - Fuselage 'ANGLE - Cowl attachment 'ANGLE - Cowl attachment 'STRIP - Windshield, front 'STRIP - Windshield. rear 'BOX ASSEMBLY - Cold air vent "VALVE "SEAL 'GASKET - Seal BLANKET - Cowl insulator, LH BLANKET - Cowl insulator. RH BLANKET - Cowl insulator, front GROMMET - Drain GROMMET GROMMET - Access GROMMET - Battery drain vent inlet with sealed battery box installation GROMMET GROMMET GROMMET GROMMET GROMMET PANEL - Side, LH PANEL - Side, RH WASHER - Cowl attachment WASHER - Fibre COVER -,Firewall, blanket, black STRINGER - Bottom STRINGER - Top STRINGER - Top. LH and RH STRINGER - LH STRINGER - AH WEBBING - Cowl (8389 ) HEADLINING ASSEMBLY - Cockpit CHANNEL - No, headlining arch CHANNEL - No, headlining arch CHANNEL - No 3. headlining arch CHANNEL - Weatherstrip WINDOW ASSEMBLY - Sliding. front 'CHANNEL - Weatherstrip 'STIFFENER - Front window CHANNEL - Weatherstrip WINDOW ASSEMBLY - Sliding rear When ordering, always specify Part Number. Description. and Serial Number of Aircrafi ISSUED: JUNE 7,988 86

41 COVERED FUSELAGE ASSEMBLY I Figure and Part Index Number Code Number PIPER PARTS CATALOG NOMENCLATURE No. Req. SECTION I Fuselage Group SERIAL NUMBERS AFFECTED 'CHANNEL - Weatherstrip CHANNEL - Weatherstrip. front and rear TRlM STRlP - Sliding window. exterior WINDOW - Rear enclosure TRlM STRlP - Sliding window. interior WASHER WASHER PANEL - Cockpit, front, LH PANEL - Cockpit, center, LH PANEL - Cockpit, rear, LH PANEL ASSEMBLY - Throttle control PANEL - Upper trim. LH TRlM STRlP - Windshield, interior, LH TRlM STRlP - Windshield, interior, RH TRlM STRlP - Windshield, exterior, LH TRlM STRlP - Windshield, exterior. RH PLATE - Trim PLATE - Trim GUSSET - Front enclosure. inside WINDOW ASSEMBLY - Top deck. tinted WINDOW ASSEMBLY - Front, left 'GASKET - Ventilator 'KNOB - Ventilator 'SCREW - Vent~lator assembly WINDSHIELD GAUGE - Air temperature ARM ASSEMBLY - Air vent control COVER - Brake line GROMMET PANEL ASSEMBLY - Rear of Throttle Panel 4 I i I / When ordering. always specify Part Number, Description, and Serial Number of Aircraft ISSUED: JUNE 7,

42 Figure 0 Covered Fuselage Assembly, Right View ISSUED: JUNE 7, PA- 8-50

43 CODE EXPLANATIONS FOR FIGURE 0 ISSUED: JUNE 7.988

44 SECTION II Fuselage Group Figure Number PIPER PARTS CATALOG NOMENCLATURE No. COVERED FUSELAGE ASSEMBLY SERIAL NUMBERS AFFECTED DOOR ASSEMBLY - Fuselage, Ceconite covered 'PLUNGER ASSEMBLY - Complete 'FRAME ASSEMBLY "HANDLE ASSEMBLY - Aluminum (for all replacement "LINK ASSEMBLY doors) PIN - Hinge WEATHERSTRIP ASSEMBLY - Enclosure door (red) WEATHERSTRIP ASSEMBLY - Enclosure door (black and white) WEATHERSTRIP ASSEMBLY - Enclosure door (black) DOOR ASSEMBLY - Upper 'STUD - Door catch 'TRIM STRIP - Front 'WINDOW MOULDING - Upper and lower enclosure doors (Die No 93 Cont Rubber Works) STRIP - Moulding attachment TRIM STRIP - Window, rear STRAP ASSEMBLY - Baggage. tip end STRAP ASSEMBLY - Baggage, buckle end PANEL - Cockpit, center, RH PANEL - Cockpit, front, RH PANEL - Cockpit, rear, RH PANEL - Cockpit, upper right FELT - Chafing, SAE F-50, x Yi" FAIRING - Fin leading edge FIN ASSEMBLY - Uncovered PANEL - Baggage compartment, rear PANEL - Baggage compartment, bottom LOCK - Control stick (used when no radio is installed) CATCH - Control lock COVER - Inspection, rectangular DECAL - "Piper Super Cub" TRIM STRIP - Window installation, top deck When ordering, always specify Part Number. Description, and Ser~al Number of Aircraft ISSUED: JUNE

45 a PIPER PARTS CATALOG Figure Fuselage Frame Assembly ISSUED: JUNE B

46 CODE EXPLANATIONS FOR FIGURE ISSUED: JUNE PA- 8-50

47 SECTION II Fuselage G I rou~ Figure and Part Index Number Number Code PIPER PARTS CATALOG NOMENCLATURE Req. FUSELAGE FRAME ASSEMBLY SERIAL NUMBERS AFFECTED 83 DRAWING - Fuselage Frame and Super Structure DRAWING - Frame Assembly, Fuselage FITTING - Rudder pedal attachment, front STOP ASSEMBLY - Fuselage door, front FITTING - Floorboard attachment BRACKET - Elevator cable pulley FlTTlNG - Rudder pedal attachment, rear FITTING - Clamp, front seat installation, front CHANNEL - Brake unit suppon FITTING ASSEMBLY - Flap lever FITTING ASSEMBLY - Landing gear, front GUSSET - Front landing gear fitting FITTING - Clamp, front seat installation. rear PLATE - Fuel shut off valve, mounting BRACKET - Stabilizer adjustment crank, right BRACKET - Stabilizer adjustment crank. left BRACKET - Rudder cable pulley STOP - Torque tube horn, left STOP - Torque tube horn, right CAPSCREW - Stop PLATE - Fuselage aileron pulley housing, left rear PLATE - Fuselage aileron pulley housing, right rear PLATE - Fuselage aileron pulley housing, front left PLATE - Fuselage aileron pulley housing, front right TUBE - Rear seat bottom, rear TUBE - Rear seat bottom, front TUBE - Square, rear seat back TOP DECK SECTION ASSEMBLY - Fuselage frame FITTING - Wing hinge. front left FITTING - Wing hinge, front right ' FITTING - Wing hinge, rear left FlTTlNG - Wing hinge. rear right STOP ASSEMBLY - Fuselage door, rear FITTING - Rear safety belt attachment BRACKET - Elevator cable pulley BRACKET ASSEMBLY - Throttle (with tube) FITTING - Landing gear and lift strut. left rear FlTTlNG - Landing gear and lift strut, right rear BUSHING - Engine mount bulkhead BULKHEAD SECTION ASSEMBLY - Fuselage frame HANDLE - Fuselage fitting BEARING - Stabilizer screw, lower BEARING - Stabilizer screw, upper BRACKET - Fin, front post attachment SUPPORT ASSEMBLY - Stabilizer TAIL POST ASSEMBLY FITTING - Tail wheel spring attachment FITTING - Tail tie rod attachment FlTTlNG - "U", tail wheel spring attachment BRACKET - Lower bungee cable pulley attachment BRACKET - Stabilizer adjustment idler CLIP - Stringer attachment CHANNEL -Window CHANNEL - Window. front. bottom, LH CHANNEL - Window BRACKET - Elevator cable pulley. lower When ordering. always specify Part Number, Description. and Serial Number of Aircraft ISSUED: JUNE

48 FUSELAGE FRAME ASSEMBLY Figure and Index Numbel I Number pan Code PIPER PARTS CATALOG NOMENCLATURE GUARD - Bungee cable pulley BRACKET ASSEMBLY - Torque tube, front bearing BRACKET ASSEMBLY - Torque tube, rear bearing CHANNEL - "U' steel %" x 0 00 (6' pieces) CHANNEL - "U" steel %" x 0 06 (6' pieces) CHANNEL - Rear window ANGLE - Baggage compartment support, rear ANGLE - Baggage compartment support, LH ANGLE - Baggage compartment support, RH CHANNEL - Upper enclosure door. top CHANNEL - Upper enclosure. rear CHANNEL - Lower enclosure door. rear CHANNEL - Lower enclosure door. front CHANNEL - Windshield, LH CHANNEL - Windshield. RH FUSELAGE FRAME AND SUPER STRUCTURE ASSEMBLY TOP DECK SECTION ASSEMBLY - Fuselage super structure HINGE - Lower enclosure door CHANNEL - Sliding window. top CHANNEL - Sliding window, bottom No. Req. - SECTION II Fuselage Group SERIAL NUMBERS AFFECTED When ordering. always specify Part Number, Description. and Serial Number of Aircraft ISSUED: JUNE

49 Figure Seats Installation ISSUED: JUNE 7, 988 C

50 CODE EXPLANATIONS FOR FIGURE ISSUED: JUNE PA- 8-50

51 SECTION II Fuselage Group Figure Part Index and Number Number Code PIPER PARTS CATALOG NOMENCLATURE No. Req. SEATS INSTALLATION SERIAL NUMBERS AFFECTED DRAWING - Shoulder Harness and Seats lnstallat~on BELT ASSEMBLY - Safety, front and rear, black STRAP ASSEMBLY - Rear. black STRAP ASSEMBLY - Front, black BRACKET ASSEMBLY - Front strap ~nstallat~on CLAMP - Front strap ~nstallat~on CUSHION ASSEMBLY - Front seat, bottom, black CUSHION ASSEMBLY - Front seat, back, black CUSHION ASSEMBLY - Rear seat, bottom, black CUSHION ASSEMBLY - Rear seat, back. black SEAT BASE ASSEMBLY - Front HANDLE ASSEMBLY - Seat release ROD - Extens~on ' SPRING - Return (48783) PIN - Stop CLIP - Fastener, #6 LEVER ASSEMBLY - Flap control 'PLUNGER ASSEMBLY - Flap control "PAWL "SPRING DECAL - Flap lever RATCHET - Flap lever TUBE - L~ner SEAT FRAME ASSEMBLY - Front 'SPRING 'SPRING 'LINK - Spr~ng connector SEAT FRAME ASSEMBLY - Rear back 'SPRING 'LINK - Spr~ng connector flap handle installat~on BOLT - AN6-7a I WASHER - Sh~m, / WASHER - ANO6O-66 NUT - MS036564C AR I ISSUED: JUNE When ordering, always specify Part Number, Description, and Serial Number of Aircraft c3

52 0 Figure 3 Rudder Pedals and Floorboards Installation ISSUED: JUNE 7,988 C4

53 I CODE EXPLANATIONS FOR FIGURE 3 ISSUED: JUNE 7.988

54 SECTION II Fuselage Group Figure and Index Number Part Number Code PIPER PARTS CATALOG NOMENCLATURE No. Req. FLOORBOARD INSTALLATION AND RUDDER PEDAL INSTALLATION SERIAL NUMBERS AFFECTED DRAWING - Rudder Pedal Installation DRAWING - Floorboards Installation FLOORBOARD ASSEMBLY - Rear FLOORBOARD - Front CLAMP SPRING - Rudder pedal LINK WASHER PEDAL ASSEMBLY - Rudder. LH PEDAL ASSEMBLY - Rudder, RH WASHER WASHER WASHER COVER - Pulley housing COVER - Pulley EXTINGUISHER - Ftre (SCT4-00) AR AR AR I I i, i I i I I I I i I i I i I I I I i I I I When ordering, always specify Part Number, Description, and Serial Number of Aircrafi ISSUED: JUNE C6

55 Figure 4 Throttle. Cabin and Carburetor Heat Mixture Controls ISSUED: JUNE 7,988 C7

56 CODE EXPLANATIONS FOR FIGURE 4 ISSUED: JUNE

57 SECTION II Fuselage Group Figure and Index Number Part Number I Code PIPER PARTS CATALOG NOMENCLATURE CABLE ASSEMBLY - Cabin and carburetor heat control 'KNOB 'CABLE ASSEMBLY - Cabin and carburetor heat control (less knob) BUSHING - Attachment, cabin and carburetor heat control cable BRACKET ASSEMBLY - Front BRACKET - Rear PANEL ASSEMBLY - Ignition switch. carburetor and cabin heat CABLE ASSEMBLY - Mixture control (less knob) KNOB - Mixture control (3004-S-M) pastel red WASHER - Throttle, vellumoid friction LUG - Friction (steel at throttle assembly) LEVER - Throttle control LINK - Throttle lever connector CABLE ASSEMBLY - Throttle control (Lycoming engine) CLAMP - Throttle control CABLE ASSEMBLY - Cold air vent control (less knob) KNOB - Cold air vent, black TUBING - Airspeed HOSE - Airspeed, rubber TUBING - Airspeed, left wing TUBE - Airspeed indicator TUBE ASSEMBLY - Airspeed (pitot and static) KNOB - Cabin and carburetor heat control KNOB - Throttle lever. black SWITCH - Ignition (#I 0-S-67 GUARD - Switch PANEL - Magneto switches HARNESS ASSEMBLY - Shielded magneto HOSE- Airspeed, rubber THROVLE. CABIN AND CARBURETOR HEAT MIXTURE CONTROLS No. Req. 4 I i / / SERIAL NUMBERS AFFECTED i ISSUED: JUNE When ordering. always specify Part Number. Descript~on. and Serial Number of Aircraft c9

58 0 Figure 5 Instrument Panel Installation (Standard) ISSUED: JUNE 7, 988 lclo PA- 8-50

59 CODE EXPLANATIONS FOR FIGURE 5 A - Washer is positioned against back side of instrument panel ISSUED: JUNE C ll

60 SECTION II Fuselage Group and Part Index Number Number Code Figure I PIPER PARTS CATALOG NOMENCLATURE DRAWING - Instrument Panel Standard Installation INSTRUMENT PANEL INSTALLATION (STANDARD) PANEL - Instrument GAUGE ASSEMBLY - Oil temperature and pressure TACHOMETER ASSEMBLY TACHOMETER ASSEMBLY SHAFT - Tachometer INDICATOR ASSEMBLY - Airspeed TUBE - Airspeed INDICATOR - Altimeter COMPASS CARD - Compass Deviation SWITCH - Starter PLACARD - Starter KNOB - Cabin air, black PRIMER ASSEMBLY KNOB - Mixture control SCREW - (MS586-) SCREW NUT - Tinnerman (A ) SCREW NUT SCREW - (MS3507-8) NUT - Tinnerman (A ) WASHER - (AN936-A46) When ordering, always specify Part Number. Description, and Serial Number of Aircraft ISSUED: JUNE 7, 988 c

61 THIS PAGE INTENTIONALLY LEFT BLANK

62 0 Figure 6 Instrument Panel Installation (With Options) ISSUED: JUNE 7, 988 C4 PA- 8-50

63 CODE EXPLANATIONS FOR FIGURE 6 A - Optional Nav/Com installations available: KX-55 Nav/Com Kit (King/Bendix ) KI-08 Vor/Loc lndicator Kit (King/Bendix ) KT-76A Transponder Kit (King/Bendix ) KY-97A Com Transceiver (King/Bendix ) MK-D Nav/Com Kit (Narco ) 0-84 Vor/Loc lndicator Kit (Narco EL ) AT- 50 Transponder Kit (Narco EL ) Escort IIA Nav/Com lndicator (Narco ) AR-850 Encoder Kit (Narco ) Piper Code Number B - Washer is positioned against back side of instrument panel ISSUED: JUNE 7,988

64 SECTION II Fuselage Group Figure and Index Number Part Number Code PIPER PARTS CATALOG NOMENCLATURE INSTRUMENT PANEL INSTALLATION (WITH OPTIONS) DRAWING - Instrument Panel Standard Installation DRAWING - Vacuum System Installation PANEL - Instrument GAUGE ASSEMBLY - Oil temperature and pressure TACHOMETER ASSEMBLY TACHOMETER ASSEMBLY SHAFT - Tachometer CLOCK INDICATOR - Turn and slip (Vacuum) INDICATOR - Turn and slip (Electric) INDICATOR ASSEMBLY - Airspeed TUBE - Airspeed INDICATOR - Directional gyro INDICATOR - Attitude gyro INDICATOR - Rate of climb INDICATOR - Altimeter INDICATOR - Navigation COMPASS CARD - Compass deviation GAUGE - Suction SWITCH - Starter PLACARD - Starter KNOB - Cabin air, black PRIMER ASSEMBLY TRANSPONDER NAV/COM KNOB - Mixture control SCREW - (MS586-) SCREW NUT SCREW - (MS3507-8) NUT - Tinnerman (A ) SCREW NUT - Tinnermen (A ) WASHER - (AN936-A46) ISSUED: JUNE When ordering. always specify Part Number, Description, and Serial Number of Aircraft C6 PA- 8-50

65 a PIPER PARTS CATALOG THIS PAGE INTENTIONALLY LEFT BLANK

66 0 Figure 7 Tail Surface Installation ISSUED: JUNE 7,988 C8

67 CODE EXPLANATIONS FOR FIGURE 7 ISSUED: JUNE 7.988

68 SECTION IV Tail Group Figure I I PIPER PARTS CATALOG and lndu I Nr:?er I Coda I NOMENCLATURE TAIL SURFACE INSTALLATION DRAWING - Tail Surface Installation , ' a loo ! l a [ ! i ' WIRE ASSEMBLY - Brace, upper WASHER - Square ' WIRE CLEVIS CLEVIS NIPPLE NUT - (No M0 elastic stop nut) WASHER - (AN960-0) BOLT - (AN4-5A) WASHER - Fin tail brace NUT - (No 4E08 elastic stop nut) BOLT - (AN3-5A) BUSHING BOLT - (AN3-5A) NUT - (No M0 elastic stop nut) WIRE ASSEMBLY - Brace, lower ' WASHER - Square ' WIRE CLEVIS ' CLEVIS ' NIPPLE ELEVATOR ASSEMBLY - Ceconite covered, LH ELEVATOR ASSEMBLY - Ceconite covered, RH ELEVATOR ASSEMBLY - Uncovered ' ENVELOPE - Elevator Assy, Ceconite (BLU PA- 8-E) ' GROMMET - (5 per elevator) BOLT - (AN3-6A) BOLT - (AN3-5A) WASHER - (AN960-0) NUT - (No MO elastic stop nut) BOLT - (AN4-6A) BUSHING WASHER - (AN960-46) NUT - (No 4E048 elastic stop nut) NUT - (AN30-3) STABILIZER ASSEMBLY - Ceconite covered, LH STABILIZER ASSEMBLY - Ceconite covered, RH ' STABILIZER ASSEMBLY - Uncovered ' ENVELOPE - Stabilizer Assy. Ceconite (BLU PA- 8-ST) ' GROMMET - Drain BOLT - (AN-3-3A) WASHER - (AN960-0) NUT - (No M0 elastic stop nut) BOLT - (AN-3-A) TUBE - Liner, rear RUDDER ASSEMBLY - Ceconite covered ' RUDDER ASSEMBLY - Uncovered ' RUDDER ASSEMBLY - Uncovered (Used with strobe if installed) ' ENVELOPE - Rudder Assy, Ceconite (BLU PA- 8-R) GROMMET - Drain (0.75 OD, 0 5 ID) ' WASHER - Drain ( 5 OD ID) ' WIRE ASSEMBLY - Tail light ' WIRE ASSEMBLY - Strobe light PIN - Hinge (AN394-55) PIN - Cotter (AN380--) WASHER BUSHING - Bronze. long BUSHING - Bronze, short DECAL - "Piper" ISSUED: JUNE When ordering, always specify Pan Number, Description, and Serial Number of Aircraft c0

69 a PIPER PARTS CATALOG THIS PAGE INTENTIONALLY LEFT BLANK

70 0 Figure 8 Land~ng Gear Installation ISSUED: JUNE 7,988 C

71 CODE EXPLANATIONS FOR FIGURE 8 A - See item 4 for washer. nut, and pin B - Refer to figure 0 for complete pans breakdown and description of Cleveland (40-60) Wheel Assembly C - Refer to figure 9 for complete parts breakdown and description of Cleveland (30-60) Brake Assembly ISSUED: JUNE 7, 988 PA- 8-50

72 SECTION V Chassis Group Figure end Index Number Part Number Code - PIPER PARTS CATALOG DRAWING - Landing Gear Installation No. LANDING GEAR INSTALLATION SERIAL NUMBERS NOMENCLATURE I Req. AFFECTED VEE ASSEMBLY - Cabane BOLT - (AN5-OA) WASHER - (AN960-66) NUT - (MS C) WASHER - (AN960-56L) BOLT - (AN6-7) BOLT - (AN6-0) WASHER - (AN960-66) NUT - (AN30-6) PIN - Cotter (MS ) STRUT ASSEMBLY - Shock. complete (Hydrasorb unit) 'PLATE - End, shock cord cover 'COVER - Shock cord 'GROMMET - Upper (AN93-4-0) 'GROMMET - Lower (AN93-6-) STRUT ASSEMBLY - Shock 'RING - Shock cord 3/4" 'TUBE ASSEMBLY - Shock, long 'STRUT - Shock, short (Hydrasorb) 'FITTING ASSEMBLY - Shock strut. upper end 'FITTING ASSEMBLY - Shock strut, lower end 'WASHER - Bumper. upper 'PIN BOLT - (AN6-7) WASHER - (AN960-66) WASHER - (AN960-66L) NUT - (MS C) BOLT - (AN6-6) WASHER - (AN960-66) WASHER - (AN960-66L) NUT - (MS C) GEAR ASSEMBLY - Landing, Ceconite covered. LH GEAR ASSEMBLY - Landing, Ceconite covered, RH 'ENVELOPE - Landing gear assembly, Ceconite (BLU PA-8-L) 'GEAR ASSEMBLY - Landing, uncovered. LH 'GEAR ASSEMBLY - Landing, uncovered. RH "BUSHING - Insert "LINE ASSEMBLY - Brake 'GROMMET - Landing Gear Vee STEP ASSEMBLY - Landing gear TIRE - (6 00 x 6. 4 ply) B F Goodrich TIRE - (6 00 x 6, 4 ply) Goodyear Flight Custom II TIRE - (6 00 x 6, 4 ply (McCreary Airhawk) TUBE x 6 COVER - Wheel SCREW - (MS3506-4) WASHER - Lock (AN936-88) NUT - Axle PIN - Axle nut WHEEL ASSEMBLY - (40-60) Cleveland BRAKE ASSEMBLY - (30-60) Cleveland BOLT - (AN4-5A) NUT - (MS C) LINE ASSEMBLY - Brake ELBOW - (400 x 4) ELBOW - (50 x 4) 4 A R 4 A R 3 3 AR ISSUED: JUNE 7, 988 When ordering, always specify Part Number, Description, and Serial Number of Aircraft C4 PA- 8-50

73 THIS PAGE INTENTIONALLY LEFT BLANK

74 0 Figure 9 Brake Assembly (Cleveland) ISSUED: JUNE D

75 CODE EXPLANATIONS FOR FIGURE 9 ISSUED: JUNE

76 SECTION V Chassis Group Figure and Index Number Part Number Code - PIPER PARTS CATALOG NOMENCLATURE BRAKE ASSEMBLY (Cleveland) BRAKE ASSEMBLY - (Cleveland 30-60) 'PLATE - Back (64-5) 'LINING - Back plate (66-56) 'RIVET - Brake lining (56) 'PLATE ASSEMBLY - Pressure (73-4) "PLATE - Pressure (63-6) "LINING - Pressure plate (66-57) 'PISTON - Cylinder (6-6) 'CYLINDER - Brake (6-67) 'PACKING - O-ring (AN67-7) 'SEAT - Bleeder (8-) 'SCREW - Bleeder (79-3) 'CAP - Bleeder (83-) 'PLATE ASSEMBLY - Torque (75-5) 'BOLT - (AN4H-5A) 'WASHER - (AN960-46L) 'BOLT - Anchor (69-L) 'NUT - Anchor (AN 'WASHER - Anchor bolt (AN960-66L) When ordering. always specify Pan Number, Description. and Serial Number of Aircraft ISSUED: JUNE ID4

77 a PIPER PARTS CATALOG Figure 0 Main Wheel Assembly (Cleveland) ISSUED: JUNE 7,988 D5

78 CODE EXPLANATIONS FOR FIGURE 0 ISSUED: JUNE 7,988 PA- 8-50

79 SECTION V Chassis Group Figure and Index Number Part Number Code PIPER PARTS CATALOG NOMENCLATURE WHEEL ASSEMBLY - (Cleveland 40-60) * WHEEL HALF ASSEMBLY - Inner ( 6-70) ' ' CUP - Bearing - (083) WHEEL HALF ASSEMBLY - Outer (6-65) ' CUP - Bear~ng (083) ' DISC ASSEMBLY - Brake ( 64-67) RING - Grease seal ( 53-) FELT - Grease seal, outer wheel ( 54-) FELT - Grease seal, inner wheel (54-8) RING - Snap ( 55-) ' BEARING - Cone (085) BOLT - (AN4-36A) ' WASHER - (AN960-46L) WASHER - (AN960-46) ' NUT - (AN365-48) No. Req MAIN WHEEL ASSEMBLY (Cleveland) SERIAL NUMBERS AFFECTED When order~ng, always spec~fy Part Number. Descript~on, and Serial Number of A~rcrafl ISSUED: JUNE 7, 988

80 0 Figure Tail Wheel Installation ISSUED: JUNE D8

81 CODE EXPLANATIONS FOR FIGURE ISSUED: JUNE

82 SECTION V Chassis Group PIPER PARTS CATALOG Figure and Part index Number Code NOMENCLATURE Number DRAWING - Tail wheel installation No. Req. TAlL WHEEL INSTALLATION SERIAL NUMBERS AFFECTED TAlL WHEEL ASSEMBLY - Complete 'WASHER 'WASHER 'BOLT - (AN7-) 'WASHER - (AN960-76) 'NUT - (#5E070) 'SPRING 'SPRING 'TAIL WHEEL ASSEMBLY - (Scott 8". #300) "BUSHING - (#34-) "SPACER - (#343-) "TIRE "TUBE "BRACKET ASSEMBLY - (#36) "WASHER - Thrust (#307) Micarta "PLATE ASSEMBLY - Thrust (#334) "SPRING - Compression (#333) "PAWL - (#39) "WASHER - Thrust (#306) "SPRING - (#3) "DUST CAP - Top (#335-) "ARM ASSEMBLY - (#34) "SPACER - (#358-) "SPACER - (#358) "PIN - (#357) "DUST CAP - Bottom (#335-) "BUSHING - (#305) "FORK ASSEMBLY - (#34) "BEARING - (#A4050 "RETAINER - Grease (#I 864) "SPACER - (#504-) "AXLE ASSEMBLY - (#336) "WASHER - Lock (#35) "BUSHING - (#37) "RETAINER - (#I 86) "BEARING ASSEMBLY - (#883) **HUB - (#598) "SPACER - (#60) BOLT - (AN6-5A) NUT - (MS C) WASHER - (AN960-66) WASHER CLAMP PAD - Tail spring BOLT - (AN4-7A) NUT - (MS C) WASHER SPRING SPRING CHAIN - (PS0076-) LINK - (PS0075-) 5 When ordering, always specify Pan Number, Description, and Serial Number of Aircraft ISSUED: JUNE PA- 8-50

83 Figure Brake Installation ISSUED: JUNE 7, 988 ldll

84 CODE EXPLANATIONS FOR FIGURE ISSUED: JUNE PA- 8-50

85 SECTION V Chassis Grou~ PIPER PARTS CATALOG BRAKE INSTALLATION Number NOMENCLATURE 4569 DRAWING - Brake Installation CYLINDER - Master brake, Scott, LH CYLINDER - Master brake, Scott, RH 'PEDAL - LH (with bushing) 'PEDAL - RH (with bushing) 'BUSHING 'SPRING 'SCREW - Vent (8-58) 'GASKET - Vent (8-59) 'PAD - Diaphragm 'DIAPHRAGM 'PISTON VALVE - Parking brake (No 400-A) 'RING - "0". 'A OD x '/a'' ID (0V70-S7-) 'RING - "0". 46 OD x 'A'' ID (0V70-S7-5) WASHER WASHER ROD - Brake lock control (No 45) ROD - Tie LINE ASSEMBLY - Flexible ELBOW - 45 No 3350 x NIPPLE - Close, /8" PLATE - Heel, cockpit floor. LH PLATE - Heel, cockpit floor, RH LINK - Pedal BLOCK - Pedal, inner BLOCK - Pedal, outer CLAMP - Pedal PEDAL ASSEMBLY - Brake. LH PEDAL ASSEMBLY - Brake, AH WASHER - Shim CLAMP - Brake installation (75-) CHANNEL - Reinforcement When ordering, always specify Part Number. Description, and Serial Number of Aircraft ISSUED: JUNE

86 -- - Figure 3 Powerplant Installation. Lycoming ISSUED: JUNE ID4

87 CODE PIPER PARTS CATALOG EXPLANATIONS FOR FIGURE 3 ISSUED: JUNE 7.988

88 SECTION VI Power~lant Grou~ Figure and index Numbe - 3- Part Number Code - PIPER PARTS CATALOG NOMENCLATURE DRAWING - Oil Radiator Installation DRAWING - Powerplant POWERPLANT INSTALLATION LYCOMING PROPELLER - Sensenich metal. 74DM BOX ASSEMBLY - Carburetor air, complete CARTRIDGE - Air filter DOME - Carburetor air filter BOX ASSEMBLY - Carburetor air - complete PLATE - Attachment BOLT - (MS ) Air box to carburetor attachment FllTlNG - Swivel, mixture control cable attachment FllTlNG - Swivel, carburetor heat control attachment at carburetor STUD - Mixture and carburetor heat control cable attachment VALVE ASSEMBLY - Oil drain CLAMP - Carburetor heat control cable attachment BUSHING - Spacer. throttle control attachment BUSHING - Spacer, throttle control attachment CLAMP - Tail pipe support. top CLAMP - Tail pipe support tube installation, bottom TUBE - Tail pipe support TUBE - Flexible, aluminum %" OD HOSE - Right rear baffle to muffler shroud HOSE - Tail pipe shroud to carburetor air box CLAMP ASSEMBLY - Exhaust stack and muffler attachme HOSE - Muffler to cabin heater STACK ASSEMBLY - Front cylinders STACK ASSEMBLY - Rear cylinders MUFFLER ASSEMBLY - Complete 'MUFFLER ASSEMBLY - Less shroud 'SHROUD - Muffler 'CLIP ASSEMBLY - Shroud HOSE ASSEMBLY - Flexible, oil pressure TUBE ASSEMBLY - Non-flexible, oil pressure CLAMP - Attachment, oil pressure line HOSE - Flexible, oil pressure line TUBE ASSEMBLY - Non-flexible, oil pressure line 3-%" L CLIP - Tinnerman (No A88-0-6) throttle control cable on firewall ANGLE - Support throttle control cable HOSE - Flexible, engine breather line connector CLAMP - (SAE TY F-IOSS) Oil breather line TUBE - Engine breather TUBE - Hold up, cowl side CLIP - Cowl hold up tube CLAMP - Tinnerman, cabin heat and mixture control cable CLAMP - Tinnerman, (A4980S--9) primer line attachment BOX ASSEMBLY - Cabin heat PLATE - Inside firewall When ordering. always specify Part Number. Description, and Serial Number of Aircraft ISSUED: JUNE Dl 6

89 POWERPLANT INSTALLATION LYCOMING PIPER PARTS CATALOG SECTION VI Power~lant Grou~ Number - NOMENCLATURE.3-43 GROMMET - Rubber (AN93-6-0) Carburetor and cabin heat control GROMMET - Rubber (AN93-4-0) Tachometer shaft. throttle mixture control GROMMET - Rubber (AN93-6-0) Air vent control cable ADAPTER - (W/H 300 x 6) BRACKET ASSEMBLY - Oil radiator support, LH BRACKET ASSEMBLY - Oil radiator support, RH CLAMP - Tinnerman (A409-S-8-9) bracket attachment ELBOW - (NO ) ELBOW - (AN8-8D) ELBOW - (NO 00-8) NIPPLE - (AN8 6-8D) LlNE ASSEMBLY - Oil cooler, left, outlet RING - Seal LlNE ASSEMBLY - Oil cooler, right, inlet HOSE ASSEMBLY - Oil cooler. right, inlet RING - Seal PLATE - Lock RADIATOR - Oil cooler, plate (PAC No ) NUT - Oil radiator BUMPER - Oil radiator. snap in (435) BRACKET - Line support. oil radiator ENGINE - Lycoming (0-30) BOLT - (AN8-44) NUT - (AN30-8) PIN - Cotter (AN ) MOUNT ASSEMBLY - Engine BOLT - (AN6-6) NUT - (AN3 0-6) PIN - Coner (AN ) WASHER - Attachment, steel WASHER - Anachrnent, fibre HINGE - Motor mount. rear HINGE - Motor mount, front LUG - Hinge attachment BRACKET ASSEMBLY - "U" BOLT - (AN6-OA) NUT - Elastic stop (4E054) CLAMP ASSEMBLY - Throttle control CLAMP ASSEMBLY - Mixture control CLAMP - Cowl support tube TUBE - Cowl support HOSE - Exhaust stack shroud to bottom cowl HOSE - Exhaust stack shroud to muffler shroud CLIP - Shroud, exhaust stack SHROUD - Exhaust stack WASHER - Attaching propeller CONNECTOR - Male. oil outlet port (500 x 8) BLOCK - Line attachment BRACKET - Baffle reinforcement PLATE - Baffle reinforcement ADAPTER- Restrictor. oil pressure ISSUED: JUNE When ordering. always specify Part Number. Description, and Serial Number of A~rcraft ID7