BU10P with through coolant supply

Transcription

1 GROOVING and BORING TOOLOLER BU with through coolant supply epth of groove up to Width of groove up to Material of shank: Carbide - Giving a good vibration resistance for use with Insert Part number d l 1 l 2 h l 4 R/LBU R/LBU R/LBU w, a, t max and f see inserts imensions in inch Further sizes upon request Ordering note: Toolholders with damaged seating can be repaired by ORN. Spare parts Toolholder Screw TORX PLUS Wrench R/LBU T8EP T8PL 2

2 GROOVING and BORING TOOLOLER with through coolant supply epth of groove up to Width of groove up to.354 (9.0 mm) Material of shank: Carbide - Giving a good vibration resistance for use with Insert Part number d l 1 l 2 h l 4 R/L R/L R/L w, a, t max and f see inserts imensions in mm Further sizes upon request Ordering note: Toolholders with damaged seating can be repaired by ORN. Spare parts Toolholder Screw TORX PLUS Wrench R/L T8EP T8PL 3

3 GROOVING and BORING TOOLOLER with through coolant supply epth of groove up to Width of groove up to.354 (9.0 mm) Material of shank: Carbide - Giving a good vibration resistance for use with Insert with 2 clamping fl ats Part number d l 1 l 2 h l 4 R/L R/L R/L w, a, t max and f see inserts imensions in mm Further sizes upon request Ordering note: Toolholders with damaged seating can be repaired by ORN. Spare parts Toolholder Screw TORX PLUS Wrench R/L T8EP T8PL 4

4 GROOVING and BORING TOOLOLER with through coolant supply epth of groove up to Width of groove up to.354 (9.0 mm) Material of shank: Carbide - Giving a good vibration resistance for use with Insert for shrinkage location S = orientation Part number d l 1 l 2 R/L S R/L S R/L S w, a, t max and f see inserts imensions in mm Further sizes upon request Ordering note: Toolholders with damaged seating can be repaired by ORN. Spare parts Toolholder Screw TORX PLUS Wrench R/L T8EP T8PL 5

5 GROOVING (internal) Ø.354 INSERT epth of groove up to Width of groove BU Part number w r s f a d t max min T35 R/L R/L R/L R/L R/L imensions in inch 6

6 GROOVING (internal) Ø.354 INSERT epth of groove up to Width of groove BU Geometry. Part number w r s f a d t max min T35 R/L R/L R/L imensions in inch 7

7 GROOVING (internal) Ø.394 INSERT epth of groove up to Width of groove BU Part number w r s f a d t max min T35 R/L R/L R/L imensions in inch 8

8 GROOVING (internal) Ø.394 INSERT epth of groove up to Width of groove BU Geometry. Part number w r s f a d t max min T35 R/L R/L imensions in inch 9

9 BORING and PROFILING Ø.346 INSERT epth of undercut up to BU Geometry.R Part number r s f a d min T35 L.1854.R2.008 R.1854.R L.1854.R4.016 R.1854.R4.016 imensions in inch The modifi ed geometry allows boring of bores Ø.346'' and profi ling of reliefs as per IN 509 form E and F. 10