Amphenol AIT/MS Series MIL-DTL-5015

Transcription

1 mphenol IT/MS Series MIL-DTL-5015 PPLICTIONS ENVIRONMENTLLY-SELED FOR CHLLENGING ENVIRONMENTS The MIL-DTL-5015 IT/MS series is a cost-effective threaded circular connector for use in harsh environments. These mphenol connectors are sealed to withstand moisture, condensation, vibration and flash-over. Over 286 contact layouts are available, in variations that allow for just power, just signal, or a mix of both contact types. vailable in five mounting styles, nineteen shell sizes, and solder or crimp termination. Formerly MIL-C-5015 Military, industrial and commercial environments requiring extreme reliability, high-power handling and cost efficiency. Power generators Engines Sensors Motion control Off-road vehicles Earth-moving equipment Ships Mobile equipment Industrial machinery Telecommunications MPHENOL IT/MS SERIES MIL-DTL-5015 FETURES GENCY PPROVLS MIL-DTL-5015 (Formerly MIL-C-5015) BROD TEMPERTURE RNGE These connectors will operate in temperatures ranging from -67 F to +257 F (-55 C to +125 C). ENVIRONMENTL These connectors will perform in the full range of operating conditions as defined in MIL-DTL-5015 and are recommended for conditions where vibration, moisture, pressure and/or temperature are extreme. RESILIENT INSULTOR ND GROMMET resilient neoprene insulator and rear-seal grommet provide a liquid-tight assembly. RUGGED SHELL The rugged aluminum alloy shell and hardware are light in weight yet highly resistant to damage and corrosion. Shells are available in five different styles and in 19 sizes. WIDE RNGE OF WIRE GUGES ND CURRENT CRRYING CPCITY Up to 150 amps for standard military contacts and up to 255 amps using Radsok contacts. Wire gauges from 24 to size 0 WG. WIDE VRIETY OF CONTCTS Machined contacts with silver or gold plating are available in sizes from 16 through 0. Solder, Crimp, PC, and thermocouple contacts are available. For assistance in Europe, please see the back cover for a complete listing of our branch offices and contact numbers. Specifications subject to change. 25

2 MPHENOL IT/MS SERIES MIL-DTL-5015 TECHNICL SPECIFICTIONS MTERILS & FINISHES Shell Plating Contacts Platings Insulator ELECTRICL DT Operating Voltage/Test Voltage MS SERVICE RTING NOMINL DISTNCE (IN.) IRSPCE CREEPGE DC V luminum alloy Olive drab chromate coating over cadmium plating to QQ-P-416; black alloy, conductive black alloy, electroless nickel, anodized or green zinc Brass or copper alloy Silver plating to QQ-S-365 (solder contacts have tinned solder pot) Gold plating to MIL-G Resilient Neoprene, Viton *, low-smoke, zero-halogen (LSZH) OPERTING VOLTGE* C VRMS STNDRD SE LEVEL CONDITIONS MINIMUM FLSHOVER VOLTGE C (RMS) TEST VOLTGE C (RMS) PRESSURE LTITUDE 50,000 FEET MINIMUM FLSHOVER VOLTGE C (RMS) TEST VOLTGE C (RMS) PRESSURE LTITUDE 70,000 FEET MINIMUM FLSHOVER VOLTGE C (RMS) TEST VOLTGE C (RMS) I 1/32 1/ ,400 1, /16 1/ ,800 2, D 1/8 3/16 1, ,600 2, E 3/16 1/4 1,750 1,250 4,500 3,500 1, B 1/4 5/16 2,450 1,750 5,700 4,500 1, C 5/16 1 4,200 3,000 8,500 7,000 1, * Each insulator has a specific service rating. These should be used by the designer only as a guide. The Service Ratings for each layout are listed on a pages Not corrected for change in density resulting from variations in temperature MS connectors show no evidence of breakdown when the given test voltages are applied between the two closest contacts and between the shell and the contacts closest to the shell for a period of one minute, per MIL-STD-1344 Method Current Rating & Contact Resistance CONTCT TEST CURRENT POTENTIL DROP CONTCT RESISTNCE SIZE (MPS) (MILLIVOLTS) (MILLIOHM) MX (50*) (69*) 26 (20*) 1 (0.44*) 4 80 (80*) 23 (18*) 0.5 (0.23*) (225*) 21 (27*) 0.2 (0.18*) *Using non-military crimp Radsok contact Maximum total current to be carried per connector in wire bundles as specified in MIL-W Contact resistance when tested to MIL-C will not exceed voltage drops listed in above table. Viton is a registered trademark of Dupont Dow Elastomers 26 For assistance in North merica: for Pricing/Delivery or Tech Support sales@peigenesis.com

3 TECHNICL SPECIFICTIONS MECHNICL Wire Range Sizes 24 to 0 WG (a crimp contacts on pages 30-31) Insulation Resistance >5000 megohms at 77 F (25 C) per MIL-DTL-5015, 3.18 Wire Sealing Range CONTCT SIZE Insulation Strip Lengths (asee page 30) Mating Life 100 cycles minimum, to MIL-DTL-5015, 3.16 Salt Spray Heat WIRE SIZE (MIL-W-5086) INSULTION OUTSIDE DIMETER LIMIT MIN. The connector is designed for individual wire sealing. Sealing of an outer cable jacket on multiconductor cables must be accomplished with an appropriate endbell. Sealing is only guaranteed if wires according to MIL-W-5086 or within the listed ranges are used. MX. IN. MM. IN. MM thru thru thru thru thru MIL-STD-1344 Method 1001 condition B minimum (cadmium), 48 hour, olive drab chromate over cadmium, non-conductive black alloy, conductive black alloy, green zinc, black anodized, electroless nickel +257 F (+125 C) for 60 hours, +185 F (+85 C) for 1,000 hours per MIL-DTL-5015, , minimum MPHENOL IT/MS SERIES MIL-DTL-5015 Chemical Resistance Vibration Shock Contact Type 20-hour full-immersion unmated in hydraulic fluid and lubricating oil per MIL-DTL-5015 minimum 10 to 2,000Hz (10g s) 10 microseconds maximum discontinuity to MIL-STD-1344 Method 2005, condition II per MIL-DTL g 11 millisecond duration, three major axes. 10 microseconds maximum discontinuity to MIL-DTL-5015 per MIL-STD-1344 method 2004, condition, 3.13 Solder, crimp, PC, or thermocouple (hard silver or gold plating) Number of Circuits 1 to 85 (asee pages 72-82) Contact Insertion Contact Retention Insertion from rear with simple hand tool. Removable, five cycles minimum. (Solder, PC and coax outer housings are bonded into the insulator.) To MIL-DTL-5015, & 3.26 and separation forces CONTCT SIZE XIL LOD SEPRTION FORCE MINIMUM NEWTONS LBS. NEWTONS LBS Polarization pprovals Integral key and keyway plus optional rotational polarization a See pages or valid rotations. MIL-DTL-5015 For assistance in Europe, please see the back cover for a complete listing of our branch offices and contact numbers. Specifications subject to change. 27

4 MPHENOL IT/MS SERIES MIL-DTL-5015 PLUGS 6 Standard (MS3106) CRETE YOUR PRT NUMBER USING THESE EIGHT STEPS STEP IT S S -472 SERIES PREFIX SHELL STYLE ENDBELLS CBLE (If omtting CLMP/BOOT endbell, enter -) (leave blank if not needed) 6B Box Mount Mates with LYOUT CONTCT ROTTION CONTCT TYPE STEP 1: SELECT SHELL STYLE, PLUG OR RECEPTCLE 0 Wall Mount with ccessory Threads (MS3100) RECEPTCLES 1 Cable Mount with ccessory Threads (MS3101) PLTING (example) 2 Box Mount No ccessory Threads (MS3102) STEP 2: SELECT ENDBELL TIP: Order connector, backshell and all accessories as one part number! See E MS Style (E/F) Standard Clamp RV No Clamp G Heat Shrink L Long Extender Unsealed (no grommet seal) F Sealed (with grommet seal) T MS Style (MS3108) 90º R MS Style Low Profile P Potting *Potting Compound asee Page 443 G2 Spin Coupling Heat Shrink U Low Cost Shielded/Unshielded STEP 3: SELECT CBLE CLMP OR BOOT (IF PPLICBLE) Heat Shrink Boot asee pages MS3057- Standard Cable Clamp C MS3057-C Gland Seal asee Page Gland Seal for Smaller Cable Range asee Page For assistance in North merica: for Pricing/Delivery or Tech Support sales@peigenesis.com

5 STEP 4: SELECT LYOUT asee pages STEP 6: SELECT ROTTION asee pages (Omit for normal) W, X, Y, Z STEP 5: SELECT CONTCT S = Solder H = PC** STEP 8: SELECT PLTING P = Pin S = Socket STEP 7: SELECT CONTCT TPYE C = Crimp* 0 = Less Contacts * When using a C in part number, the connector is supplied with the standard size crimp contacts for its layout. Bolded part numbers on apage 30 indicate crimp contact. Please contact us for connectors with reduced or enlarged crimp barrel contacts. **asee page 38 for post diameters and lengths MPHENOL IT/MS SERIES MIL-DTL-5015 CONTCTS (Omit for silver contacts) B30 = Gold 50µ Gold over Nickel T = Thermocouple (solder only) Need types with cavities and installed and uninstalled RDS = RDSOK (Crimp socket only) sizes 12,8,4,0 116 = Less pre-tinned solder cups SHELL PLTING (Omit for olive drab chromate over cadmium) (MS style) 023 = Electroless Nickel (RoHS with crimp or 116 contacts) 024 = Green Zinc Cobalt 025 = Black lloy (RoHS with crimp or 116 contacts) 027 = Conductive Black lloy (RoHS with crimp or 116 contacts) G96 = Black nodized 472 = 116&025 mod codes (RoHS) 548 = 116&023 mod codes (RoHS) 553 = 116&027 mod codes (RoHS) MTERILS (Omit for standard neoprene) L = Low-smoke, zero-halogen V = High-temperature Viton STNDRD SPECILS CONTCT US WITH NPT THRED SIZE, SEL TITE CONDUIT DIMETER, OR CBLE OUTSIDE DIMETER. INTERNL THRED VERSION LOW COST GLND SEL CONDUIT METL SHIELDED CBLE EXTERNL THRED VERSION CONDUIT PLSTIC GLND SEL MESH GRIP asee pages 445 aneed HELP? PEI engineers will help you solve your design challenges and build the perfect part for your application. us at sales@peigenesis.com or complete our online Technical Request at To contact us by phone, please see the back cover for a complete listing of our branch offices and contact numbers. For assistance in Europe, please see the back cover for a complete listing of our branch offices and contact numbers. Specifications subject to change. 29

6 MPHENOL IT/MS SERIES MIL-DTL-5015 CONTCT SIZE WIRE SIZE WG PIN CONTCT PIN CONTCT PIN & SOCKET CRIMP CONTCTS SOCKET CONTCT SOCKET CONTCT SILVER GOLD SILVER GOLD 16S IC16S-16P* IC16S-16PG* IC16S-16S* IC16S-16SG* 16S IC16S-12P IC16S-12PG IC16S-12S IC16S-12SG C IC16S-14P IC16S-14PG IC16S-14S IC16S-14SG C IC16S-20P IC16S-20PG IC16S-20S IC16S-20SG C IC16S-22P IC16S-22PG IC16S-22S IC16S-22SG C IC16S-24P IC16S-24PG IC16S-24S IC16S-24SG C IC16-16P* IC16-16PG* IC16-16S* IC16-16SG* IC16-12P IC16-12PG IC16-12S IC16-12SG C IC16-14P IC16-14PG IC16-14S IC16-14SG C IC16-18P IC16-18PG IC16-18S IC16-18SG C IC16-20P IC16-20PG IC16-20S IC16-20SG C IC P IC PG IC S IC SG C IC16-22P IC16-22PG IC16-22S IC16-22SG C2 WIRE STRIP LENGTHS INCHES (MM) IC12-12P* IC12-12PG* IC12-12S* IC12-12SG*.312 (7.9) High-Power - - IC12-12SRD IC12-8P IC12-8PG IC12-8S IC12-8SG C IC12-10P IC12-10PG IC12-10S IC12-10SG C IC12-14P IC12-14PG IC12-14S IC12-14SG C IC12-16P IC12-16PG IC12-16S IC12-16SG C IC12-18P IC12-18PG IC12-18S IC12-18SG C IC12-20P IC12-20PG IC12-20S IC12-20SG C IC8-8P* IC8-8PG* IC8-8S* IC8-8SG* 8 PRT NUMBER 8 High-Power - - IC8-8SRD IC8-10P IC8-10PG IC8-10S IC8-10SG C IC8-12P IC8-12PG IC8-12S IC8-12SG C IC4-4P* IC4-4PG* IC4-4S* IC4-4SG* 4 4 High-Power - - IC4-4SRD - 8 IC4-8P IC4-8PG IC4-8S IC4-8SG C IC0-0P* IC0-0PG* IC0-0S* IC0-0SG*. 0 0 High-Power - - IC0-0SRD IC0-2P IC0-2PG IC0-2S IC0-2SG C11 4 IC0-4P IC0-4PG IC0-4S IC0-4SG C12 WIRE STRIP LENGTH (7.9) (7.9) (14.3) (12.7) (19.0) WIRE RNGE WIRE SELING RNGE INCHES (MM) ( ) ( ) ( ) ( ) ( ) *Bolded items are standard crimp contacts. SOLDER THERMOCOUPLE CONTCTS TYPE PINS SOCKETS 16S lumel P* S* 16S Chromel P* S* Iron P* S* Constantan P* S* 16 lumel P* S* 16 Chromel P* S* Iron P* S* Constantan P* S* SOLDER THERMOCOUPLE CONTCTS TYPE PINS SOCKETS 12 lumel P* S* 12 Chromel P* S* Iron P* S* Constantan P* S* Thermocouple Types: J = Iron-Constantan K = lumel-chromel T = Copper-Constantan E = Chromel-Constantan *Contact us for availability. Contact information is below. 16S contacts are used in 8S, 10S, 10SL, 12S, 14S & 16S connector sizes only. 30 For assistance in North merica: for Pricing/Delivery or Tech Support sales@peigenesis.com

7 CCESSORIES Insert head first. Trim excess CONTCT SIZE 16S 16 F8 WIRE HOLE FILLER COLOR Blue MS TH29-1 PIN & SOCKET CRIMP CONTCTS CRIMP TOOLS F8-(hand) (pneumatic) W27F 400BHD Die set, locator and Go-No-Go gauge CRIMP LOCTOR & DIE SETS TH29-1 TOOLS LOCTOR COLOR Red Pin-Blue W27F- Socket- Green PILOT PIN/INSERTION GUIDE FOR SOCKETS INSERTION TOOL DK EXTRCTION TOOL DRK59 Kit with Multiple Tips MPHENOL IT/MS SERIES MIL-DTL Yellow MS Green DK Red MS Die Set 414D-8N Locator 4025-Pin 4026-Socket DK282 4 Blue MS BHD Die Set 414D-4N Locator IC4INS IC4EXT 0 Yellow MS Die Set 414D-0N Locator IC0INS IC0EXT Contact us for additional tool accessories. Contact information is below. ll dimensions in inches (millimeters in parenthesis) For assistance in Europe, please see the back cover for a complete listing of our branch offices and contact numbers. Specifications subject to change. 31

8 MPHENOL IT/MS SERIES MIL-DTL-5015 COX CONTCT SIZE 12 COX WIRE SIZE RG161/U RG174/U RG179B/U RG187/U RG188/U RG316/U RG178B/U RG196/U RG58C/U RG141/U RG303/U PINS PIN & SOCKET COX CONTCTS SOCKETS SILVER GOLD SILVER GOLD (1) PIN CONTCT () () (5) (3) () PRT NUMBER SOCKET CONTCT (1) () () () (5) () (3) () WIRE STRIP LENGTH WIRE STRIP LENGTHS INCHES (mm) Contact us for details. WIRE RNGE WIRE SELING RNGE INCHES (mm) MIN. MX (3.2 mm) (4.5 mm) CCESS- ORIES Insert head first. Trim excess. WIRE HOLE FILLER Yellow RG59B/U RG62/U RG62B/U RG210/U (1) (5) (3) () () (1) (5) (3) () () 8 RG161/U RG174/U RG179B/U RG187/U RG188/U RG316/U (1) (5) (3) () () (1) (5) (3) () () Contact us for details (3.8 mm) (6.5 mm) White RG180B/U RG195/U (5) () () (6) () () RG140/U RG302/U (5) () (5) () RG55B/U RG142/U RG142B/U RG223/U (5) () (5) () RG59B/U RG62/U RG62B/U RG210/U () () 4 RG212/U () () Contact us for details (7.1 mm) (9.3 mm) Blue RG55B/U RG142/U RG142B/U RG223/U () () ( ) Various platings available. vailability of coax contacts varies widely. Contact us for details. Contact information is below. ll dimensions in inches (millimeters in parenthesis) 32 For assistance in North merica: for Pricing/Delivery or Tech Support sales@peigenesis.com

9 COX CONTCT SIZE 12 COX WIRE SIZE RG161/U RG174/U RG179B/U RG187/U RG188/U RG316/U RG178B/U RG196/U PIN & SOCKET COX CONTCTS M22520/10-01 Crimp Dies TOOLS HND CRIMP TOOL CRIMP DIES USE LOCTOR M22520/10-05 B COX CLMP NUT WRENCH MPHENOL IT/MS SERIES MIL-DTL-5015 RG58C/U RG141/U RG303/U M22520/10-01 M22520/10-07 B RG59B/U RG62/U RG62B/U RG210/U M22520/5-01 M22520/5-45 B RG161/U RG174/U RG179B/U RG187/U RG188/U RG316/U M22520/10-05 RG180B/U RG195/U M22520/10-01 B RG140/U RG302/U M22520/10-07 RG55B/U RG142/U RG142B/U RG223/U RG59B/U RG62/U RG62B/U RG210/U M22520/5-01 M22520/5-45 B B - 4 RG212/U RG55B/U RG142/U RG142B/U RG223/U M22520/5-01 M22520/5-39 M22520/5-34 M22520/10-01 M22520/ ll dimensions in inches (millimeters in parenthesis) For assistance in Europe, please see the back cover for a complete listing of our branch offices and contact numbers. Specifications subject to change. 33

10 MPHENOL IT/MS SERIES MIL-DTL-5015 RECEPTCLE STYLES IT0-MS3100 IT2-MS3102 DIMENSIONS IT0-MS3100 IT2-MS3102 IT0-MS3100/IT2-MS3102 IT2-MS3102IT0/IT1 IT1 IT0/IT1 M T DI. L REF KK DI. LENGTH B THRED SHELL THRED R S LENGTH CLSS 2 SIZE CLSS P REF. +/ / Q DI. 8S UNEF (14.3) (2.8) (15.1) (22.2) (3.0) 10S NEF (14.3) (2.8) (18.3) (25.4) (3.0) 10SL NEF (14.3) (2.8) (18.3) (25.4) (3.0) 12S UNEF (14.3) (2.8) (20.6) (27.8) (3.0) UNEF (19.1) (2.8) (20.6) (27.8) (3.0) 14S UNEF (14.3) (2.8) (23.0) (30.2) (3.0) UNEF (19.1) (2.8) (23.0) (30.2) (3.0) 16S UNEF (14.3) (2.8) (24.6) (32.5) (3.0) UNEF (19.1) (2.8) (24.6) (32.5) (3.0) NEF (19.1) (3.6) (27.0) (34.9) (3.0) NEF (19.1) (3.6) (29.4) (38.1) (3.0) NEF (19.1) (3.6) (31.8) (41.3) (3.0) NEF (20.6) (3.6) (34.9) (44.5) (3.7) NS (20.6) (3.6) (39.7) (50.8) (3.7) NS (22.2) (4.0) (44.5) (57.2) (4.4) UN (22.2) (4.0) (49.2) (63.5) (4.4) UN (22.2) (4.0) (55.6) (69.9) (4.4) (24.6) (9.5) (24.6) (12.7) (24.6) (15.9) (24.6) (15.9) (34.1) (15.9) (24.6) (19.1) (34.1) (19.1) (24.6) (22.2) (34.1) (22.2) (34.1) (25.4) (34.1) (28.6) (34.1) (31.8) (35.7) (34.9) (35.7) (41.3) (37.3) (47.6) (37.3) (52.4) (37.3) (58.7) IT1-MS3101 IT1-MS (27.6) (13.5) (27.6) (16.0) (27.6) (19.2) (27.6) (19.2) (33.9) (19.2) (27.6) (22.4) (33.9) (22.4) (27.6) (25.7) (33.9) (25.7) (33.9) (28.9) (33.9) (32.1) (33.9) (35.4) (35.7) (38.6) (35.7) (45.1) (37.3) (50.7) (37.3) (57.2) (37.3) (63.7) UNEF UNEF UNEF UNEF UNEF UNEF UNEF UNEF UNEF UNEF UNEF UNEF UNEF UNEF UN UN UN ll dimensions in inches (millimeters in parenthesis) 34 For assistance in North merica: for Pricing/Delivery or Tech Support sales@peigenesis.com

11 ENDBELL STYLES SHELL SIZE 8S UNEF (35.3) (81.20) 10S UNEF (37.3) (81.20) 10SL NEF (37.3) (93.6) 12S NEF (37.3) NEF (46.8) - 14S UNEF (37.3) (82.09) UNEF (46.8) - 16S UNEF (37.3) (82.09) UNEF (46.8) (91.03) UNEF (49.2) (92.94) NEF (46.8) (92.56) NEF (49.2) (92.68) NEF (50.0) (94.64) NEF (55.6) (98.96) NS (54.8) (104.24) NS (56.4) (105.38) UN (55.6) (105.38) L 3 XX DIMENSIONS E IT0-MS3100/IT1-MS3101 (MS-E/F) & L ENDBELL E ENDBELL R ENDBELL L 1 L 2 MX. B THRED CLSS 2 L XX CBLE MIN (54.1) (7.1) (54.1) (7.1) (54.1) (7.1) (55.9) (10.3) (62.1) (10.3) (55.9) (12.7) (62.1) (12.7) (65.9) (13.5) (67.4) (16.7) (67.4) (18.8) (73.3) (19.8) (73.3) (23.4) (74.8) (29.4) (74.8) (31.8) (77.9) (39.7) L L L 4 H DI MX (40.3) (24.4) (40.3) (26.1) (40.3) (28.4) (40.3) (28.4) (49.0) (28.4) (40.3) (33.2) (49.0) (33.2) (40.3) (36.4) (49.0) (36.4) (49.0) (39.5) (49.0) (44.3) (49.0) (47.5) (51.0) (50.6) (51.0) (55.0) (52.6) (64.5) (52.6) (69.3) (52.6) (75.7) H L MX. R (MS-R) J ±.008 (±0.2) IT0/IT1 G K ±.020 (+0.5) Z MIN (50.0) (3.5) (11.7) (7.7) (13.3) (15.5) (50.0) (3.5) (11.7) (10.6) (17.0) (19.1) (50.0) (3.5) (11.7) (13.5) (21.9) (23.9) (60.0) (3.5) (11.5) (13.5) (21.9) (23.9) (60.0) (3.5) (11.5) (14.5) (21.9) (23.9) (65.0) (3.5) (12.7) (18.7) (26.2) (29.6) (65.0) (3.5) (12.7) (20.8) (26.2) (29.6) (65.0) (3.5) (12.7) (24.6) (34.5) (37.8) (65.0) (3.5) (12.7) (27.0) (34.5) (37.8) (70.0) (3.5) (15.2) (33.3) (43.6) (47.8) (80.0) (3.5) (15.2) (38.5) (43.6) (47.8) (80.0) (3.5) (15.5) (48.2) (52.6) (57.8) G BB MX. JJ (+.02) MPHENOL IT/MS SERIES MIL-DTL-5015 ll dimensions in inches (millimeters in parenthesis) For assistance in Europe, please see the back cover for a complete listing of our branch offices and contact numbers. Specifications subject to change. 35

12 MPHENOL IT/MS SERIES MIL-DTL-5015 STYLE 6 PLUGS (BRREL SSEMBLY) IT6-MS3106 MS3108 DIMENSIONS STYLE 6 ENDBELLS E MS3106E MS3106F L & L MS3106E/MS3106F Q1 BRREL SHELL THRED DI. B THRED SIZE CLSS 2B MX. CLSS 2 B THRED L 1 L 2 CLSS 2 L MX. CBLE MIN. XX 8S UNEF UNEF (18.8) 10S NEF UNEF (22.1) 10SL NEF UNEF (24.0) 12S UNEF UNEF (25.3) UNEF UNEF (25.3) 14S UNEF UNEF (28.5) UNEF UNEF (28.5) 16S UNEF UNEF (31.8) UNEF UNEF (31.8) NEF UNEF (33.9) NEF UNEF (37.1) NEF UNEF (40.3) NEF UNEF (43.6) NS UNEF (50.0) NS UN (56.1) UN UN (62.6) UN UN (69.1) UNEF (35.3) UNEF (37.3) NEF (37.3) (93.6) NEF (37.3) NEF (46.8) UNEF (37.3) (95.2) UNEF (46.8) UNEF (37.3) (95.2) UNEF (46.8) (94.2) UNEF (49.2) (104.0) NEF (46.8) (104.0) NEF (49.2) (104.2) NEF (50.0) (100.4) NEF (55.6) (111.6) NS (54.8) (128.0) NS (56.4) (100.6) UN (55.6) (110.6) (54.1) (7.1) (54.1) (7.1) (54.1) (7.1) (55.9) (10.3) (64.1) (10.3) (55.9) (12.7) (64.1) (12.7) (65.9) (13.5) (67.4) (16.7) (67.4) (18.8) (73.3) (19.8) (73.3) (23.4) (74.8) (29.4) (74.8) (31.8) (77.9) (39.7) ll dimensions in inches (millimeters in parenthesis) 36 For assistance in North merica: for Pricing/Delivery or Tech Support sales@peigenesis.com

13 STYLE 6 RIGHT NGLE ENDBELLS H R MS3106R L DIMENSIONS G T MS3108 MS3108E MPHENOL IT/MS SERIES MIL-DTL-5015 R G 3108 SHELL H DI. SIZE L MX. MX. J ±.008 K Z BB JJ L MX. (±0.2) (+0.5) MIN. MX. (+0.2) L MX. B THRED CLSS 2 8S (40.3) (24.4) 10S (40.3) (26.1) 10SL (40.3) (28.4) 12S (40.3) (28.4) (49.0) (28.4) 14S (40.3) (33.2) (49.0) (33.2) 16S (40.3) (36.4) (49.0) (36.4) (49.0) (39.5) (49.0) (44.3) (49.0) (47.5) (51.0) (50.6) (51.0) (55.0) (52.6) (64.5) (52.6) (69.3) (52.6) (75.7) (50.0) (3.5) (11.7) (7.7) (13.3) (15.5) (50.0) (3.5) (11.7) (10.6) (17.0) (19.1) (50.0) (3.5) (11.7) (13.5) (21.9) (23.9) (60.0) (3.5) (11.5) (13.5) (21.9) (23.9) (60.0) (3.5) (11.5) (14.5) (21.9) (23.9) (65.0) (3.5) (12.7) (18.7) (26.2) (29.6) (65.0) (3.5) (12.7) (20.8) (26.2) (29.6) (65.0) (3.5) (12.7) (24.6) (34.5) (37.8) (65.0) (3.5) (12.7) (27.0) (34.5) (37.8) (70.0) (3.5) (15.2) (33.3) (43.6) (47.8) (80.0) (3.5) (15.2) (38.5) (43.6) (47.8) (80.0) (3.5) (15.5) (48.2) (52.6) (57.8) UNEF (36.2) UNEF (37.0) NEF (37.6) NEF (37.8) NEF (47.3) UNEF (41.9) UNEF (48.9) UNEF (42.6) UNEF (52.1) UNEF (53.7) NEF (60.0) NEF (60.0) NEF (66.4) NEF (66.4) NS (72.1) NS (73.5) UN (76.7) ll dimensions in inches (millimeters in parenthesis) For assistance in Europe, please see the back cover for a complete listing of our branch offices and contact numbers. Specifications subject to change. 37

14 MPHENOL IT/MS SERIES MIL-DTL-5015 PRINTED CIRCUIT CONTCTS DIMENSIONS USE IT OR M T DI. KK DI. SHELL MPHENOL THRED P R (TP) S Y REF. SIZE PRT NUMBER CLSS REF. +/ / REF. L X REF. +/ S XXX UNEF (14.3) (2.8) (15.1) (22.2) (3.0) (24.6) (9.5) (15.1) (4.8) 10S XXX NEF (14.3) (2.8) (18.3) (25.4) (3.0) (24.6) (12.7) (15.1) (4.8) 10SL XXX NEF (14.3) (2.8) (18.3) (25.4) (3.0) (24.6) (15.9) (15.1) (4.8) 12S XXX UNEF (14.3) (2.8) (20.6) (27.8) (3.0) (24.6) (15.9) (15.1) (4.8) XXX UNEF (19.1) (2.8) (20.6) (27.8) (3.0) (34.1) (15.9) (19.9) (4.8) 14S XXX UNEF (14.3) (2.8) (23.0) (30.2) (3.0) (24.6) (19.1) (15.1) (4.8) XXX UNEF (19.1) (2.8) (23.0) (30.2) (3.0) (34.1) (19.1) (19.9) (4.8) 16S XXX UNEF (14.3) (2.8) (24.6) (32.5) (3.0) (24.6) (22.2) (15.1) (4.8) XXX UNEF (19.1) (2.8) (24.6) (32.5) (3.0) (34.1) (22.2) (19.9) (4.8) XXX NEF (19.1) (3.6) (27.0) (34.9) (3.0) (34.1) (25.4) (19.9) (4.8) XXX NEF (19.1) (3.6) (29.4) (38.1) (3.0) (34.1) (28.6) (19.9) (4.8) XXX NEF (19.1) (3.6) (31.8) (41.3) (3.0) (34.1) (31.8) (19.9) (4.8) XXX NEF (20.6) (3.6) (34.9) (44.5) (3.7) (35.7) (34.9) (19.9) (4.8) XXX NS (20.6) (3.6) (39.7) (50.8) (3.7) (35.7) (41.3) (19.9) (4.8) XXX NS (22.2) (4.0) (44.5) (57.2) (4.4) (37.3) (47.6) (19.9) (4.8) XXX UN (22.2) (4.0) (49.2) (63.5) (4.4) (37.3) (52.4) (19.9) (4.8) XXX UN (22.2) (4.0) (55.6) (69.9) (4.4) (37.3) (58.7) (19.9) (4.8) XXX = Insert layout code. Contact us for correct code. Contact information is below. ll dimensions in inches (millimeters in parenthesis) 38 For assistance in North merica: for Pricing/Delivery or Tech Support sales@peigenesis.com

15 PNEL CUTOUTS Dimension J is flange in front of panel. Dimension K is flange at rear of panel. See sealing screws on apage 439. SHELL SIZE DIMENSIONS 8S (15.1) (3.4) (10.1) (15.4) 10S (18.2) (3.4) (13.3) (18.5) 10SL (18.2) (3.4) (16.4) (18.5) 12S/ (20.6) (3.4) (16.4) (21.7) 14S/ (23.0) (3.4) (19.7) (24.9) 16S/ (24.6) (3.4) (22.9) (27.7) (27.0) (3.4) (26.1) (31.1) (29.4) (3.4) (29.5) (34.5) (31.8) (3.4) (32.7) (37.8) (34.9) (3.9) (36.0) (41.3) (39.7) (3.9) (42.0) (47.1) (44.5) (4.5) (48.3) (53.8) (49.2) (4.5) (54.6) (60.0) (55.5) (4.5) (61.2) (66.3) ++ 6B panel plug is front mount only. FLNGE STYLE 0-2-6B MOUNTING HOLE FRONT MOUNT RER MOUNT DIMETER G H J K MPHENOL IT/MS SERIES MIL-DTL-5015 PNEL THICKNESS Max screwhead Front Mount Max screwhead & panel thickness Rear Mount SHELL SIZE FRONT MOUNT RER MOUNT 8SL.125 (3.18) 10S.125 (3.18) 10SL.125 (3.18) 12S/12SL.125 (3.18) (4.75) 14S.187 (4.75) 16S.187 (4.75) (4.75).125 (3.18) (4.75) (4.75) (4.75) (4.75) (4.75) (6.35) (6.35) (6.35) ll dimensions in inches (millimeters in parenthesis) For assistance in Europe, please see the back cover for a complete listing of our branch offices and contact numbers. Specifications subject to change. 39

16 IT/MS MPHENOL INDUSTRIL THREDED/MS/MIL-DTL-5015 SERIES Pre-Earth Series/FMLB PPLICTIONS FIRST-MTE, LST-BREK (FMLB) CONNECTOR THT INTERMTES WITH MIL-DTL-5015 mphenol s DL Pre-Earth /FMLB (first-mate, last-break) connectors are designed for applications where a protective circuit from the ground contact to the shell is a safety requirement. These connectors provide a path for stray voltage to be shunted to a safe ground to avoid damage to sensitive equipment or harm to operators. Intermateable with IT, MIL-DTL-5015 & 97 series UL-listed FETURES LYOUT Conformity with European (CE) safety standards (DIN VDE 0627 and certified through TUV Product Service GmbH) in the approved insert arrangement Offered in shell styles: 3102 box mount and 3106 straight plug Intermateable with IT, MIL-DTL-5015 and 97 styles Class IP67 protection when mated UL-listed file # E Pre-earth (ground contact) design First-mate/last-break capability CRETE YOUR PRT NUMBER USING THESE THREE STEPS DL S CONNECTOR TYPE LYOUT CONTCT STEP 1: SELECT SHELL STYLE PLUGS Power generators Engines Sensors Motion control Off-road vehicles Earth-moving equipment Ships Mobile equipment Industrial machinery Telecommunications RECEPTCLES (example) STEP 2: SELECT LYOUT MTING VIEW OF PIN INSERT TOTL CONTCTS CURRENT RTING (MPS) CONTCT SIZE SL B C D C E B D F C B F E G B D C D C B DL3106 Plug DL3102 Box Mount Receptacle F E G B * D C F E G B D C Indicates Pre-Earth contact only *Pre-Earth contact in plug STEP 3: SELECT CONTCT P = Pin S = Socket 40 For assistance in North merica: for Pricing/Delivery or Tech Support sales@peigenesis.com

17 MS3057- CBLE CLMP MS3057-C WTERPROOF CBLE CLMP CCESSORIES Standard MS3057 cable clamps have dual-clamping action to provide a balanced, positive hold on the wires and greatly reduce moisture transmission. This cable clamp accepts MS3420 bushings. MS3420 bushings can be nested to reduce the inside diameter (ID) to more closely match the diameter of the cable or wire bundle. STNDRD CLMP LUMINUM W/ MXIMUM SHELL THRED LOW-COST LUMINUM W/ STINLESS STEEL CBLE DIMETER SIZE CLSS 2B CST ZINC BRSS SCREWS SCREWS INCH (MM) 8S/10S 1/2-28UNEF - MS M85049/ (6.35) 10SL 5/8-24UNEF ** MS M85049/ (7.92) 12/12S 5/8-24UNEF ** MS M85049/ (7.92) 12SL/14S 3/4-20UNEF ** MS M85049/ (11.10) 16/16S 7/8-20UNEF ** MS M85049/ (14.27) UNEF ** MS M85049/ (15.88) 20/22 1 3/16-18UNEF ** MS M85049/ (19.05) 24/28 1 7/16-18UNEF ** MS M85049/ (23.80) /4-18UNS ** MS M85049/ (31.75) UNS ** MS M85049/ (34.92) /4UNS-16 - MS M85049/ (41.28) STNDRD CLMP & TELESCOPIC BUSHING LOW-COST ZINC WITH BUSHING BUSHING ID BUSHING INCLUDED INCH (MM) - MS (3.3) MS (5.6) MS (5.6) MS (7.9) MS (11.1) MS (14.3) MS (15.9) MS , (15.9) MS , (19.1) MS , (23.8) Default plating is CD OD. ** Other platings are available. asee page MPHENOL IT/MS SERIES MIL-DTL-5015 Standard MS3057-C waterproof cable clamp with mechanical strain relief for use with threaded endbells. Internal neoprene gland and compression ring will seal a broad range of round cable diameters, as listed below. For reduction of cable diameters, order the appropriate MS3420 bushing in table. SHELL WIRE DIMETER INCHES (MM) OPTIONL BUSHINGS SIZE PRT NUMBER MX. MIN. PRT NUMBER MX. WIRE DI. (MM) 8S/10S MS3057-3C (5.56) (2.41) MS (3.17) 10SL/12S/12 MS3057-4C (7.93) (4.80) MS (5.56) 12SL/14S MS3057-6C (11.12) (7.10) MS (7.93) MS (5.56) 16/16S MS3057-8C (13.48) (7.90) MS (11.1) MS (7.93) 18 MS C (15.87) (9.50) MS (11.1) MS (7.93) 20/22 MS C (19.00) (12.70) MS (13.74) MS (11.10) 24/28 MS C (23.80) (15.90) MS (19.00) MS (13.74) MS (11.10) 32 MS C (31.75) (23.40) MS (23.8) MS (19.00) MS (13.74) 36 MS C (35.00) 1.00 (25.40) MS (28.50) MS (23.80) MS (19.00) 40 MS C (41.25) 1.25 (31.80) MS (31.75) MS (23.80) MS (19.00) ll dimensions in inches (millimeters in parenthesis) For assistance in Europe, please see the back cover for a complete listing of our branch offices and contact numbers. Specifications subject to change. 41

18 MPHENOL IT/MS SERIES MIL-DTL-5015 MS3420 TELESCOPING BUSHINGS SHELL SIZE 1ST BUSHING PRT NUMBER MS3420- REDUCTION BUSHINGS CCESSORIES For use with style- cable clamps and IT/MS style-e/f endbells to resist dust, dirt, and oil. Bushings can be nested, one inside the other, to reduce the inside diameter to better seal against the cable jacket. Each bushing will accept the next smallest bushing. INSIDE DIMETER 2ND NESTED BUSHING INSIDE DIMETER FITS IN CBLE CLMP 8S/10S MS (3.30) NONE - MS SL/12/12S MS (5.59) NONE - MS /14S MS (7.92) NONE - MS S MS (11.10) NONE - MS MS (11.10) NONE - MS MS (14.30) NONE - MS MS (15.90) NONE - MS MS (15.90) NONE - MS MS (19.05) MS (15.90) MS MS (19.05) MS (15.90) MS MS (23.80) MS (19.05) MS MS (31.75) MS (23.80) MS MS (34.92) MS (31.75) SE For use with MS3057-C cable clamps (style-c) to reduce the wire-sealing diameter. Bushings can be nested, one inside the other, to progressively reduce the inside diameter of the cable clamp. The column labeled re duction bushings shows the acceptable nesting options for each clamp CBLE CLMPS 9767 waterproof cable clamp with mechanical strain relief. n internal Neoprene gland seal bushing and compression washer will seal a broad range of round cable diameters as listed below. SHELL SIZE CBLE CLMP PRT NUMBER MX. CBLE OUTSIDE DIMETER MIN. CBLE OUTSIDE DIMETER THRED INCHES MM INCHES MM CLSS 2B UNEF 10SL/12S/ / S / S / S/ / S/ / S/ / / / / / / / / / / / / / /4-18UNS UNS ll dimensions in inches (millimeters in parenthesis) 42 For assistance in North merica: for Pricing/Delivery or Tech Support sales@peigenesis.com

19 GSKETS CCESSORIES Synthetic rubber gaskets are used to ensure a moisture-tight seal between a receptacle and the panel. Gaskets are available for front or rear panel mounting of style-0, 2, and 6B connectors. Gasket thickness is approximately.031 inches (1 mm), for nonconductive and low-temperature types. Conductive shielding gaskets contain an imbedded metal screen for EMI/RFI shielding in addition to moisture sealing. Gaskets are available for front or rear panel mounting of connectors. Gasket thickness is.020 inches (.5 mm). SHELL SIZE NON-CONDUCTIVE CONDUCTIVE LOW-TEMPERTURE -67ºF (-55ºC) 8S S S/10SL S /12S S /14S S S S S S S S S S S S S MPHENOL IT/MS SERIES MIL-DTL-5015 METL DUST CPS WITH SSH CHIN & DUMMY RECEPTCLES Metal dust caps are used to protect the contacts when the connectors are left unmated. Dust caps come with metal chain lanyards. Dummy receptacles are for front or rear panel mounting. The center of the dummy receptacle is closed. Dummy receptacles mount on the same centers and have the same outside dimensions as MS3102 receptacles. version with a clearance hole through the middle of the connector is also available. Call for ordering information; contact information is below. DUST CPS PLUG CP RECEPTCLE DUMMY RECEPTCLES SHELL SIZE 8S MS * MS * MS3105-8S 10S/10SL MS * MS * MS S 12/12S/12SL MS * MS * MS S 14S MS * MS * MS S 16S MS * MS * MS S 16 MS * MS * MS MS * MS * MS MS * MS * MS MS * MS * MS MS * MS * MS MS * MS * MS MS * MS * MS MS * MS * MS MS * MS * MS *Contact us for other platings. *D = Olive drab chromate over cadmium D = nodized For assistance in Europe, please see the back cover for a complete listing of our branch offices and contact numbers. Specifications subject to change. 43

20 MPHENOL IT/MS SERIES MIL-DTL-5015 SOLDER CONTCTS STEP 1: Slide the rear accessories over the wire bundle in the proper sequence for re-assembly: cable clamp and/or endbell first, then ferrule and (if used) coupling nut. STEP 5: Slide the grommet down the wires (lubricating the grommet with isopropyl alcohol will help). CRIMP TOOL OPERTION SSEMBLY INSTRUCTIONS STEP 2: Insert individual wires through the proper holes in the grommet. Use isopropyl alcohol as a lubricant. STEP 6: Fill all unused grommet cavities with a wire hole filler to maintain the sealing integrity of the connector. LOCTOR STEP 3: Solder wires to appropriate contacts on the rear of the connector. Information on standard soldering practices is available upon request. Please contact us. LTCH CRIMP TOOL STEP 7: Slide coupling nut, ferrule, and endbell accessories over rear of the connector and tighten. For tooling, asee page 122. STEP 4: Fixture the connector for reassembly using the endbell assembly tools on apage 122. LOCTOR LTCH LOCTOR COLOR CODE INDEX MRK TURRET STEP 1: Strip the wires to the appropriate length. See strip lengths on the Contact Selection Guide, apage 30. STEP 2: Open the crimp tool by squeezing the handles. Push the latch on the turret to release the locator. ttach the turret to the crimp tool using the two captive hex bolts in the turret. NOTE: Hand-crimp tools can be used with size 16S, 16 & 12 contacts. Size 8, 4 and 0 contacts require the use of air-powered crimp tools. Contact us for assistance in the use of these tools. STEP 3: Select the proper locator position for your contact by rotating the locator until the proper color is aligned with the index mark. Push locator back down until it snaps into position. CONTCT PIN LOCTOR SOCKET SIZE COLOR LOCTOR COLOR 16S Blue Blue 16 Green Red 12 Red Red DIL LOCK PIN STEP 4: djust dial for proper wire gauge. To change the dial setting, remove the lock pin and lift center of dial. Turn to the desired wire gauge. Replace lock pin on dial. STEP 5: Cycle the tool before inserting the contact to be sure the tool is in the open position. Drop the contact, mating end first, into the crimp cavity of the tool. Squeeze the tool handle just enough to grip the contact without actually crimping it. STEP 6: Insert the stripped wire into the contact with a slight twisting motion. Be sure all wire strands are inside the contact. Squeeze the handle to cycle the tool. The handle will not release until the contact is completely crimped. 44 For assistance in North merica: for Pricing/Delivery or Tech Support sales@peigenesis.com

21 CRIMP TOOL OPERTION (CONTINUED) CRIMP CHECK TO BE SURE CONDUCTOR IS VISIBLE THROUGH WIRE INSPECTION HOLE WIRE INSULTION SHOULD PRESS GINST THE END OF THE CONTCT. STEP 7: Remove the crimped contact. Pull on the wire slightly to be sure it is properly crimped. Be sure the contact is not bent or damaged in any way. Visually inspect the crimp. MICRO-SECTIONS: Enlargement of micro-section permits a final inspection of crimp quality. This test is recommended whenever new tools or new types of wire or contacts are used. INSERTION OF CONTCTS SSEMBLY INSTRUCTIONS GUIDE (PILOT) PIN INSERTION TOOL CRIMP TENSILE STRENGTH Initial minimum pullout force in lbs. (before conditioning) SIZE WIRE GUGE (WG) LB MPHENOL IT/MS SERIES MIL-DTL-5015 SHOULDER STEP 1: Slide the rear accessories over the wire bundle in the proper sequence for re-assembly: cable clamp and/or endbell first, then ferrule, and coupling nut. STEP 2: Use the proper insertion tool from the Contact Selection Chart on apage 31. Place the contact in the tool. The tool should push against the shoulder of the contact. Contact sizes 16S, 16, and 12 use a pliers-style tool. Contact sizes 8, 4 and 0 use a tool with a C-shaped shaft. STEP 3: Lubricate the grommet with isopropyl alcohol (do not use any other type of lubricant). Insert the contact through the appropriate cavity in the grommet. Sizes 16S, 16 and 12 socket contacts must be installed using guide (pilot) pins. See the Contact Selection Guide on apage 31 for Insertion Guide (Pilot) Pin part numbers. CONNECTOR SSEMBLY FIXTURE STEP 4: Place the connector into an assembly fixture. Fixtures are available for production use; contact us using the information below. If you are not using a fixture, be sure to allow clearance on the mating face of the connector for the guide pins to come through the connector during insertion. STEP 5: Lubricate the contact cavities of the connector insulator with isopropyl alcohol (do not use any other type of lubricant). STEP 6: Using guide pins where necessary, push straight down with a firm, even pressure until the contact snaps into position in the proper cavity. Start at the center of the pattern and work toward the outer edges. For assistance in Europe, please see the back cover for a complete listing of our branch offices and contact numbers. Specifications subject to change. 45

22 MPHENOL IT/MS SERIES MIL-DTL-5015 INSERTION OF CONTCTS (CONTINUED) UNCRIMPED CONTCTS STEP 7: Fill any unused cavities with contacts. EXTRCTION OF CONTCTS SSEMBLY INSTRUCTIONS STEP 8: Check the mating face of the connector to ensure that all of the same size contacts are on the same plane (fully inserted). If not, the contact is not fully inserted. Remove the contact using the proper extraction tool and procedure, and reinsert. Do not attempt to reinsert the insertion tool to correct the problem. STEP 9: wire hole filler must be inserted into the grommet behind the unused contacts to maintain the sealing integrity of the connector. See the Contact Selection Chart on apage 31 for wire hole fillers. STEP 10: Place the connector back in the fixture for re-assembly. Slide the connector accessories back down the cable over the rear of the connector and tighten. Use the appropriate endbell tools as shown on apage 122. SOCKET EXTRCTION END SOFT JW PLIERS LOCK RING HNDLE PIN EXTRCTION END STEP 1: Remove the endbell accessories and slide them back over the wires. Use the appropriate endbell tools as shown on apage 122. STEP 2: Use the proper extraction tool from the Contact Selection Chart on apage 31. The extraction tool can be used for both pin and socket contacts by removing the shaft from the handle and reversing it for pin or socket extraction. CROSS-SECTION OF CONNECTOR CROSS-SECTION OF CONNECTOR PIN CONTCT SOCKET CONTCT STEP 3: On the mating face of the connector, insert the tool over the pin contact or into the socket contact until the tool touches bottom. pply a slow, continuous pressure to push the contact out through the rear of the connector. When the shoulder of the tool thunks against the insulator, the contact is extracted. STEP 4: Carefully remove the extraction tool from the connector to avoid damage to the insulator. 46 For assistance in North merica: for Pricing/Delivery or Tech Support sales@peigenesis.com

23 Mates with IT/MS SERIES CONNECTORS CONNECTOR TYPE J MS SHELL STYLE Prefix* Military Standard 3100 = Wall-mounting receptacle 3101 = Cable-connecting receptacle (plug ) 3102 = Box-mounting receptacle 3106 = Straight plug 3108 = 90 plug SERVICE CLSS Solid shell, not MS qualified C Solid shell for pressurized applications E F R Environmentally-resistant Environmentally-resistant with strain relief (J MS part number only) MPHENOL HOW-TO-ORDER GUIDE J MS 3102 R 18-3 P W -RES Lightweight, environmentally-resistant (J MS part number only; not available for 3108) (NOT J MS) Modification for -style service class only RESilient insert (neoprene) INSERT ROTTION W, X, Y, and Z designate that the insert is rotated in its shell from normal position. No letter is required for normal (no rotation) position. See tables on apages CONTCT TYPES P Pin contact S Socket contact Note: The US military changed the designation from cable receptacle to plug in the MIL-DTL-5015 specifications MPHENOL IT/MS SERIES MIL-DTL-5015 SHELL SIZE & INSERT RRNGEMENT See tables on apages Parts are the only MS-approved inserts. For insert arrangements over 50 and shell size 40 and above. Exceptions: 36-52, 40-1, 40-9 and are approved. *The March 30, 2003 revision of MIL-DTL-5015H requires that the letters JN or J be physically marked on the connector preceding the MS designator. This mark certifies that the connector meets specification. The United States Government has obtained Certificate and Registration Number 504,860 for the certification mark JN and Registration Number 1,586,261 for the certification mark J. HVE UNIQUE REQUIREMENT? Quick assembly of custom products is our specialty! us at sales@peigenesis.com or complete our online Technical Request at To contact us by phone, please see the back cover for a complete listing of our branch offices and contact numbers. For assistance in Europe, please see the back cover for a complete listing of our branch offices and contact numbers. Specifications subject to change. 47