WHEN YOU NEED THE BEST IN 5015 CONNECTORS

Transcription

1

2 WHEN YOU NEED THE BET IN 5015 CONNECTO

3 TBE OF CONTENT 5015 Connectors everse Bayonet Connectors Ordnance Connectors & ccessories Insert Configurations ccessories Index Crown can supply connectors with the following: 5015 PECI FETUE 1. Plugs with a self-locking coupling nut, which eliminates the need for safety wire. low-cost coupling mechanism is available for all series. 2. Our connectors can provide superior EI/FI shielding by:. Providing full accessory teeth at the rear of the connector shell, thus minimizing leakage. B. To further enhance performance, plugs can be supplied with grounding fingers around the outside of the barrel. C. eceptacles can be supplied with an internal grounding spring. 3. s/hardware can be provided in a high impact/ strength aluminum as well as carbon steel, 300 series stainless and naval brass. 4. wide range of finishes are available:. nodize - both hard and soft B. Cadmium to pass 48, 96, 500 or 1000 hours salt spray C. Electroless nickel D. Zinc Boron E. Black zinc F. Nickel teflon 5. tandard insert material is neoprene, but can be provided in fuel-resistant Viton or halogen-free neoprene. 6. Various backshell configurations are available for environmental and non-environmental applications together with EI/FI protection. Crown Connector 3060 North Walnut oad, Unit 160 North as Vegas, NV Cage Code:

4 5015 ODE 5015 ODE ODEING INFOTION C P W F80 COWN PEFIX HE TYE ee Table 1 below. Illustrated on pages 3 thru 11. BCEND TEINTION/C ee Table II below. HE IZE INET CONFIGUTION Per I-TD ee pages 27 thru 32 for codes and illustrations. CONTCT TYE P Pin contacts. ocket Contacts. TENTE POITION (POIZTION) Blank (Normal) W, X Y, Z ee pages 27 thru 32. ODIFICTION Blank Contacts: older Type upplied. -95 Contacts: Gold Plated per I-G Type II, Class 2 Over Nickel Contacts: Gold Plated per I-G Type II, Class 2 Over Gold Flash per I-G Type I Over Copper Plate per I-C-14550, Class 4. -C2 Chemical Film, per I-C F0 Connector ess Contacts. -F28 Cinch Nut ounting. -F80 WG Crimp Contacts upplied with, but Not Installed in Connector. -H Hex Coupling Nut. - Passivated tainless teel. -Z3 Zinc Nickel Colbalt, Olive Drab. -Z9 Zinc Nickel Colbalt, Black. -1 Electroless Nickel. -11 upplied Unmarked * ess Bushing. -14 upplied ess End Bell. -17 upplied with Gasket for Plug or eceptacle * with Bushing Contacts: Gold Over Nickel. For other codes, contact ales Dept. TBE I. HE TYE tyle Description 3100 Wall mount receptacle 3101 In-line receptacle 3102 Box mount receptacle 3103P Wall mount receptacle, potting seal 3104 Jam Nut receptacle 3106 traight plug 3106P traight plug, potting seal Plug TBE II. C Code Description Environmental Grommet Threaded adapter No No B Threaded adapter Yes Yes E Threaded adapter Yes No D Backshell, 2 piece with 3057* Clamp Yes No F Backshell, 2 piece with 3057* Clamp Yes Yes Backshell, 2 piece with 3057*C Clamp Yes No P Potting boot Yes No 2

5 W OUNT ECEPTCE C3100, B, D, E, F 5015 ODE ØT 4 HOE THED V THED TYP. TYP. C3100 Threaded adapter, non-environmental, less grommet C3100B Threaded adapter, environmental, with grommet C3100E Threaded adapter, environmental, less grommet Coupling Thread Class ( ) ±.005 (±0.13) ±.031 (±0.79) X. T ( ) V ccessory Thread Class 2 in. 10 5/8-24 UNEF.156 (3.96).062 (1.57) (38.89).562 (14.27).719 (18.26) (25.40).120 (3.05) 5/8-24 UNEF 12 3/4-20 UNEF.156 (3.96).062 (1.57) (52.37).750 (19.05).812 (20.62) (27.79).120 (3.05) 5/8-24 UNEF 12 3/4-20 UNEF.156 (3.96).062 (1.57) (42.88).562 (14.27).812 (20.62) (27.79).120 (3.05) 5/8-24 UNEF 14 7/8-20 UNEF.156 (3.96).062 (1.57) (52.37).750 (19.05).906 (23.01) (30.18).120 (3.05) 3/4-20 UNEF 14 7/8-20 UNEF.156 (3.96).062 (1.57) (42.88).562 (14.27).906 (23.01) (30.18).120 (3.05) 3/4-20 UNEF UNEF.156 (3.96).062 (1.57) (52.37).750 (19.05).969 (24.61) (32.54).120 (3.05) 7/8-20 UNEF UNEF.156 (3.96).062 (1.57) (42.88).562 (14.27).969 (24.61) (32.54).120 (3.05) 7/8-20 UNEF /8-18 UNEF.203 (5.16).094 (2.39) (52.37).750 (19.05) (26.97) (34.92).120 (3.05) 1-20 UNEF /4-18 UNEF.203 (5.16).094 (2.39) (55.58).750 (19.05) (29.36) (38.10).120 (3.05) 1 3/16-18 UNEF /8-18 UNEF.203 (5.16).094 (2.39) (55.58).750 (19.05) (31.75) (41.27).120 (3.05) 1 3/16-18 UNEF /2-18 UNEF.203 (5.16).094 (2.39) (58.72).812 (20.62) (34.92) (44.45).147 (3.73) 1 7/16-18 UNEF /4-18 UN.203 (5.16).094 (2.39) (58.72).812 (20.62) (39.67) (50.80).147 (3.73) 1 7/16-18 UNEF UN.359 (9.12).125 (3.17) (61.93).875 (22.22) (44.45) (57.15).173 (4.39) 1 3/4-18 UN ØT 4 HOE THED 3057-* CBE CP TYP. TYP. CBE NGE Y F X. C3100D Two (2) piece backshell w/ 3057* clamp, non-environmental, less grommet C3100F Two (2) piece backshell w/ 3057* clamp, environmental, with grommet Coupling Thread Class 2 F ( ) ±.005 (±0.13) ±.031 (±0.79) T ( ) in. Open Closed 10 5/8-24 UNEF.156 (3.96).062 (1.57) (58.42).562 (14.27).719 (18.26) (25.40).120 (3.05).938 (23.83).312 (7.92).125 (3.18) 12 3/4-20 UNEF.156 (3.96).062 (1.57) (73.66).750 (19.05).812 (20.62) (27.79).120 (3.05).938 (23.83).312 (7.92).125 (3.18) 12 3/4-20 UNEF.156 (3.96).062 (1.57) (63.50).562 (14.27).812 (20.62) (27.79).120 (3.05).938 (23.83).312 (7.92).125 (3.18) 14 7/8-20 UNEF.156 (3.96).062 (1.57) (73.66).750 (19.05).906 (23.01) (30.18).120 (3.05) (28.58).438 (11.13).250 (6.35) 14 7/8-20 UNEF.156 (3.96).062 (1.57) (63.50).562 (14.27).906 (23.01) (30.18).120 (3.05) (28.58).438 (11.13).250 (6.35) UNEF.156 (3.96).062 (1.57) (73.66).750 (19.05).969 (24.61) (32.54).120 (3.05) (33.32).562 (14.27).312 (7.92) UNEF.156 (3.96).062 (1.57) (63.50).562 (14.27).969 (24.61) (32.54).120 (3.05) (33.32).562 (14.27).312 (7.92) /8-18 UNEF.203 (5.16).094 (2.39) (73.66).750 (19.05) (26.97) (34.92).120 (3.05) (33.32).625 (15.88).350 (8.89) /4-18 UNEF.203 (5.16).094 (2.39) (76.20).750 (19.05) (29.36) (38.10).120 (3.05) (38.89).750 (19.05).500 (12.70) /8-18 UNEF.203 (5.16).094 (2.39) (76.20).750 (19.05) (31.75) (41.27).120 (3.05) (38.89).750 (19.05).500 (12.70) /2-18 UNEF.203 (5.16).094 (2.39) (82.55).812 (20.62) (34.92) (44.45).147 (3.73) (44.45).938 (23.83).625 (15.88) /4-18 UN.203 (5.16).094 (2.39) (82.55).812 (20.62) (39.67) (50.80).147 (3.73) (44.45).938 (23.83).625 (15.88) UN.359 (9.12).125 (3.17) (91.44).875 (22.22) (44.45) (57.15).173 (4.39) (53.16) (31.75).875 (22.23) Plug has O ring under coupling nut. Y ±.020 (±0.51) Cable ange 3

6 5015 ODE W OUNT ECEPTCE C3100 / C3103P ØT 4 HOE THED 3057-*C CBE CP TYP. TYP. Z CBE NGE N C3100 Two (2) piece backshell w/ 3057*C clamp, environmental, less grommet Coupling Thread Class 2 N T Z ±.005 ± Cable Cable ange ( ) (±0.13) (±0.79) ( ) Clamp in. eries CF eries Free Closed 10 5/8-24 UNEF.156 (3.96).062 (1.57) (58.42) 4.00 (101.6).562 (14.27).937 (23.80).719 (18.26) (25.40).120 (3.05) C.312 (7.92).094 (2.39) 12 3/4-20 UNEF.156 (3.96).062 (1.57) (73.66) 4.50 (114.0).750 (19.05).937 (23.80).812 (20.62) (27.79).120 (3.05) C.312 (7.92).094 (2.39) 12 3/4-20 UNEF.156 (3.96).062 (1.57) (63.50) 4.00 (101.6).562 (14.27).937 (23.80).812 (20.62) (27.79).120 (3.05) C.312 (7.92).094 (2.39) 14 7/8-20 UNEF.156 (3.96).062 (1.57) (73.66) 4.50 (114.0).750 (19.05) (26.97).906 (23.01) (30.18).120 (3.05) C.438 (11.13).250 (6.35) 14 7/8-20 UNEF.156 (3.96).062 (1.57) (63.50) 4.00 (101.6).562 (14.27) (26.97).906 (23.01) (30.18).120 (3.05) C.438 (11.13).250 (6.35) UNEF.156 (3.96).062 (1.57) (73.66) 4.50 (114.0).750 (19.05) (30.18).969 (24.61) (32.54).120 (3.05) C.531 (13.49).312 (7.92) UNEF.156 (3.96).062 (1.57) (63.50) 4.00 (101.6).562 (14.27) (30.18).969 (24.61) (32.54).120 (3.05) C.531 (13.49).312 (7.92) /8-18 UNEF.203 (5.16).094 (2.39) (73.66) 4.69 (119.0).750 (19.05) (33.32) (26.97) (34.92).120 (3.05) C.625 (15.88).375 (9.52) /4-18 UNEF.203 (5.16).094 (2.39) (76.20) 4.69 (119.0).750 (19.05) (39.67) (29.36) (38.10).120 (3.05) C.750 (19.05).500 (12.70) /8-18 UNEF.203 (5.16).094 (2.39) (76.20) 4.69 (119.0).750 (19.05) (39.67) (31.75) (41.27).120 (3.05) C.750 (19.05).500 (12.70) /2-18 UNEF.203 (5.16).094 (2.39) (82.55) 4.90 (124.2).812 (20.62) (44.45) (34.92) (44.45).147 (3.73) C.938 (23.83).594 (15.09) /4-18 UN.203 (5.16).094 (2.39) (82.55) 5.13 (130.0).812 (20.62) (44.45) (39.67) (50.80).147 (3.73) C.938 (23.83).594 (15.09) UN.359 (9.12).125 (3.17) (91.44) 5.39 (137.0).875 (22.22) (57.15) (44.45) (57.15).173 (4.39) C (31.75).938 (23.83) ØT 4 HOE THED POTTING FO TYP. TYP. C3103P Environmental potting seal Coupling Thread Class 2 in ( ) ±.005 (±0.13) X. ±.031 (±0.79) T ( ) 10 5/8-24 UNEF.156 (3.96).062 (1.57) (38.89).562 (14.27).719 (18.26) (25.40).120 (3.05) 12 3/4-20 UNEF.156 (3.96).062 (1.57) (49.99).750 (19.05).812 (20.62) (27.79).120 (3.05) 12 3/4-20 UNEF.156 (3.96).062 (1.57) (38.89).562 (14.27).812 (20.62) (27.79).120 (3.05) 14 7/8-20 UNEF.156 (3.96).062 (1.57) (49.99).750 (19.05).906 (23.01) (30.18).120 (3.05) 14 7/8-20 UNEF.156 (3.96).062 (1.57) (38.89).562 (14.27).906 (23.01) (30.18).120 (3.05) UNEF.156 (3.96).062 (1.57) (49.99).750 (19.05).969 (24.61) (32.54).120 (3.05) UNEF.156 (3.96).062 (1.57) (38.89).562 (14.27).969 (24.61) (32.54).120 (3.05) /8-18 UNEF.203 (5.16).094 (2.39) (49.99).750 (19.05) (26.97) (34.92).120 (3.05) /4-18 UNEF.203 (5.16).094 (2.39) (55.58).750 (19.05) (29.36) (38.10).120 (3.05) /8-18 UNEF.203 (5.16).094 (2.39) (55.58).750 (19.05) (31.75) (41.27).120 (3.05) /2-18 UNEF.203 (5.16).094 (2.39) (55.58).812 (20.62) (34.92) (44.45).147 (3.73) /4-18 UN.203 (5.16).094 (2.39) (55.58).812 (20.62) (39.67) (50.80).147 (3.73) UN.359 (9.12).125 (3.17) (55.58).875 (22.22) (44.45) (57.15).173 (4.39) 4

7 IN-INE ECEPTCE C3101, B, D, E, F 5015 ODE N X. THED X. C3101 Threaded adapter, non-environmental, less grommet C3101B Threaded adapter, environmental, with grommet C3101E Threaded adapter, environmental, less grommet V THED Coupling Thread Class 2 N V ccessory Thread Class 2 8 1/2-28 UNEF (37.31).844 (21.44) 1/2-28 UNEF 10 5/8-24 UNEF (38.89).969 (24.61) 1/2-28 UNEF 10 5/8-24 UNEF (38.89) (26.97) 5/8-24 UNEF 12 3/4-20 UNEF (42.88) (26.97) 5/8-24 UNEF 12 3/4-20 UNEF (42.88) (26.97) 5/8-24 UNEF 14 7/8-20 UNEF (52.37) (29.36) 3/4-20 UNEF 14 7/8-20 UNEF (42.88) (29.36) 3/4-20 UNEF UNEF (52.37) (31.75) 7/8-20 UNEF UNEF (42.88) (31.75) 7/8-20 UNEF /8-18 UNEF (52.37) (34.14) 1-20 UNEF /4-18 UNEF (55.58) (38.00) 1 3/16-18 UNEF /8-18 UNEF (55.58) (40.49) 1 3/16-18 UNEF /2-18 UNEF (58.72) (43.66) 1 7/16-18 UNEF /4-18 UN (58.72) (50.01) 1 7/16-18 UNEF UN (61.93) (56.36) 1 3/4-18 UN /4-16 UN (61.93) (62.71) 2-18 UN /2-16 UN (61.93) (69.06) 2 1/4-16 UN /4-16 UN (65.07) (75.41) 2 1/2-16 UN UN (65.07) (81.76) 3-16 UN THED 3057-* CBE CP N X. CBE NGE Y F X. C3101D Two (2) piece backshell w/ 3057* clamp, non-environmental, less grommet C3101F Two (2) piece backshell w/ 3057* clamp, environmental, with grommet Coupling Thread Class 2 F N Y ±.020 (±0.51) Cable ange Open Closed 10 5/8-24 UNEF (58.42) (26.97).938 (23.83).312 (7.92).125 (3.18) 12 3/4-20 UNEF (73.66) (26.97).938 (23.83).312 (7.92).125 (3.18) 12 3/4-20 UNEF (63.50) (26.97).938 (23.83).312 (7.92).125 (3.18) 14 7/8-20 UNEF (73.66) (29.36) (28.58).438 (11.13).250 (6.35) 14 7/8-20 UNEF (63.50) (29.36) (28.58).438 (11.13).250 (6.35) UNEF (73.66) (31.75) (33.32).562 (14.27).312 (7.92) UNEF (63.50) (31.75) (33.32).562 (14.27).312 (7.92) /8-18 UNEF (73.66) (34.14) (33.32).625 (15.88).350 (8.89) /4-18 UNEF (76.20) (38.00) (38.89).750 (19.05).500 (12.70) /8-18 UNEF (76.20) (40.49) (38.89).750 (19.05).500 (12.70) /2-18 UNEF (82.55) (43.66) (44.45).938 (23.83).625 (15.88) /4-18 UN (82.55) (50.01) (44.45).938 (23.83).625 (15.88) UN (91.44) (56.36) (53.16) (31.75).875 (22.23) Plug has O ring under coupling nut. 5

8 5015 ODE IN-INE & BOX OUNT ECEPTCE C3101 / C3102, E THED 3057-*C CBE CP N X. Z CBE NGE BB C3101 Two (2) piece backshell w/ 3057*C clamp, environmental, less grommet Coupling Thread Class 2 BB N Cable Clamp Z Cable ange eries CF eries Free Closed 10 5/8-24 UNEF.937 (23.80) (58.42) 4.00 (101.6) (26.97) C.312 (7.92).094 (2.39) 12 3/4-20 UNEF.937 (23.80) (73.66) 4.50 (114.0) (26.97) C.312 (7.92).094 (2.39) 12 3/4-20 UNEF.937 (23.80) (63.50) 4.00 (101.6) (26.97) C.312 (7.92).094 (2.39) 14 7/8-20 UNEF (26.97) (73.66) 4.50 (114.0) (29.36) C.438 (11.13).250 (6.35) 14 7/8-20 UNEF (26.97) (63.50) 4.00 (101.6) (29.36) C.438 (11.13).250 (6.35) UNEF (30.18) (73.66) 4.50 (114.0) (31.75) C.531 (13.49).312 (7.92) UNEF (30.18) (63.50) 4.00 (101.6) (31.75) C.531 (13.49).312 (7.92) /8-18 UNEF (33.32) (73.66) 4.69 (119.0) (34.14) C.625 (15.88).375 (9.52) /4-18 UNEF (39.67) (76.20) 4.69 (119.0) (38.00) C.750 (19.05).500 (12.70) /8-18 UNEF (39.67) (76.20) 4.69 (119.0) (40.49) C.750 (19.05).500 (12.70) /2-18 UNEF (44.45) (82.55) 4.90 (124.2) (43.66) C.938 (23.83).594 (15.09) /4-18 UN (44.45) (82.55) 5.13 (130.0) (50.01) C.938 (23.83).594 (15.09) UN (57.15) (91.44) 5.39 (137.0) (56.36) C (31.75).938 (23.83) ØT 4 HOE THED TYP. TYP. C3102 Non-environmental C3102E Environmental Coupling Thread Class 2 in ( ) ±.005 (±0.13) X. ±.031 (±0.79) T ( ) 10 5/8-24 UNEF.156 (3.96).062 (1.57) (30.96).562 (14.27).719 (18.26) (25.40).120 (3.05) 12 3/4-20 UNEF.156 (3.96).062 (1.57) (41.28).750 (19.05).812 (20.62) (27.79).120 (3.05) 12 3/4-20 UNEF.156 (3.96).062 (1.57) (30.96).562 (14.27).812 (20.62) (27.79).120 (3.05) 14 7/8-20 UNEF.156 (3.96).062 (1.57) (41.28).750 (19.05).906 (23.01) (30.18).120 (3.05) 14 7/8-20 UNEF.156 (3.96).062 (1.57) (30.96).562 (14.27).906 (23.01) (30.18).120 (3.05) UNEF.156 (3.96).062 (1.57) (41.28).750 (19.05).969 (24.61) (32.54).120 (3.05) UNEF.156 (3.96).062 (1.57) (30.96).562 (14.27).969 (24.61) (32.54).120 (3.05) /8-18 UNEF.203 (5.16).094 (2.39) (49.23).750 (19.05) (26.97) (34.92).120 (3.05) /4-18 UNEF.203 (5.16).094 (2.39) (49.23).750 (19.05) (29.36) (38.10).120 (3.05) /8-18 UNEF.203 (5.16).094 (2.39) (49.23).750 (19.05) (31.75) (41.27).120 (3.05) /2-18 UNEF.203 (5.16).094 (2.39) (49.23).812 (20.62) (34.92) (44.45).147 (3.73) /4-18 UN.203 (5.16).094 (2.39) (49.23).812 (20.62) (39.67) (50.80).147 (3.73) UN.359 (9.12).125 (3.17) (49.23).875 (22.22) (44.45) (57.15).173 (4.39) 6

9 J NUT ECEPTCE C3104, E 5015 ODE F P THED H Z P C3104 Non-environmental C3104E Environmental Coupling Thread Class 2 F ±.016 (±0.41) H Panel Thickness in..045 IN. [1.14] OCWIE HOE ±.005 (±0.13) ±.010 (±0.25) P ±.010 (±0.25) ±.010 (±0.25) Z ±.045 (±1.14) 10 5/8-24 UNEF.812 (20.62) 0.00 (0.00).204 (5.18).156 (3.96).812 (20.62).354 (8.99) (25.40).281 (7.14) 12 3/4-20 UNEF.938 (23.83) 0.00 (0.00).204 (5.18).156 (3.96).812 (20.62).397 (10.08) (28.58).281 (7.14) 12 3/4-20 UNEF.938 (23.83) 0.00 (0.00).329 (8.36).156 (3.96) (30.18).397 (10.08) (28.58).344 (8.74) 14 7/8-20 UNEF (26.97) 0.00 (0.00).142 (3.61).156 (3.96).812 (20.62).442 (11.23) (31.75).281 (7.14) 14 7/8-20 UNEF (26.97) 0.00 (0.00).267 (6.78).156 (3.96) (30.18).442 (11.23) (31.75).344 (8.74) UNEF (31.75) 0.00 (0.00).142 (3.61).156 (3.96).812 (20.62).486 (12.34) (34.93).281 (7.14) UNEF (31.75) 0.00 (0.00).267 (6.78).156 (3.96) (30.18).486 (12.34) (34.93).344 (8.74) /8-18 UNEF (33.32) 0.00 (0.00).235 (5.97).188 (4.78) (29.36).575 (14.61) (41.28).375 (9.52) /4-18 UNEF (38.10) 0.00 (0.00).235 (5.97).188 (4.78) (29.36).619 (15.72) (44.45).375 (9.52) /8-18 UNEF (39.67) 0.00 (0.00).235 (5.97).188 (4.78) (29.36).663 (16.84) (47.63).375 (9.52) /2-18 UNEF (44.45) 0.00 (0.00).298 (7.57).188 (4.78) (30.96).707 (17.96) (50.80).312 (7.92) /4-18 UN (50.80) 0.00 (0.00).298 (7.57).188 (4.78) (30.96).795 (20.19) (57.15).312 (7.92) UN (55.58) 0.00 (0.00).329 (8.36).219 (5.56) (31.75).884 (22.45) (63.50).281 (7.14) 7

10 5015 ODE TIGHT PUG C3106, B, D, E, F X. THED X. C3106 Threaded adapter, non-environmental, less grommet C3106B Threaded adapter, environmental, with grommet C3106E Threaded adapter, environmental, less grommet V THED Coupling Thread Class 2B V ccessory Thread Class /8-24 UNEF (38.89).969 (24.61) 5/8-24 UNEF 12 3/4-20 UNEF (52.37) (26.97) 5/8-24 UNEF 12 3/4-20 UNEF (42.88) (26.97) 5/8-24 UNEF 14 7/8-20 UNEF (52.37) (29.36) 3/4-20 UNEF 14 7/8-20 UNEF (42.88) (29.36) 3/4-20 UNEF UNEF (52.37) (31.75) 7/8-20 UNEF UNEF (42.88) (31.75) 7/8-20 UNEF /8-18 UNEF (52.37) (34.14) 1-20 UNEF /4-18 UNEF (55.58) (37.31) 1 3/16-18 UNEF /8-18 UNEF (55.58) (40.49) 1 3/16-18 UNEF /2-18 UNEF (58.72) (43.66) 1 7/16-18 UNEF /4-18 UN (58.72) (50.01) 1 7/16-18 UNEF UN (61.93) (56.36) 1 3/4-18 UN THED 3057-* CBE CP X. CBE NGE Y C3106D Two (2) piece backshell w/ 3057* clamp, non-environmental, less grommet C3106F Two (2) piece backshell w/ 3057* clamp, environmental, with grommet Coupling Thread Class 2B F F X. Y ±.020 (±0.51) Open Cable ange Closed 10 5/8-24 UNEF (58.42).969 (24.61).938 (23.83).312 (7.92).125 (3.18) 12 3/4-20 UNEF (73.66) (26.97).938 (23.83).312 (7.92).125 (3.18) 12 3/4-20 UNEF (63.50) (26.97).938 (23.83).312 (7.92).125 (3.18) 14 7/8-20 UNEF (73.66) (29.36) (28.58).438 (11.13).250 (6.35) 14 7/8-20 UNEF (63.50) (29.36) (28.58).438 (11.13).250 (6.35) UNEF (73.66) (31.75) (33.32).562 (14.27).312 (7.92) UNEF (63.50) (31.75) (33.32).562 (14.27).312 (7.92) /8-18 UNEF (73.66) (34.14) (33.32).625 (15.88).350 (8.89) /4-18 UNEF (76.20) (37.31) (38.89).750 (19.05).500 (12.70) /8-18 UNEF (76.20) (40.49) (38.89).750 (19.05).500 (12.70) /2-18 UNEF (82.55) (43.66) (44.45).938 (23.83).625 (15.88) /4-18 UN (82.55) (50.01) (44.45).938 (23.83).625 (15.88) UN (91.44) (56.36) (53.16) (31.75).875 (22.23) Plug has O ring under coupling nut. 8

11 TIGHT PUG C3106, P 5015 ODE THED 3057-*C CBE CP X. Z CBE NGE N C3106 Two (2) piece backshell w/ 3057*C clamp, environmental, less grommet Coupling Thread Class 2B N Cable Clamp Z Cable ange eries CF eries Free Closed 10 5/8-24 UNEF (58.42) 4.00 (101.6).937 (23.80).969 (24.61) C.312 (7.92).094 (2.39) 12 3/4-20 UNEF (73.66) 4.50 (114.0).937 (23.80) (26.97) C.312 (7.92).094 (2.39) 12 3/4-20 UNEF (63.50) 4.00 (101.6).937 (23.80) (26.97) C.312 (7.92).094 (2.39) 14 7/8-20 UNEF (73.66) 4.50 (114.0) (26.97) (29.36) C.438 (11.13).250 (6.35) 14 7/8-20 UNEF (63.50) 4.00 (101.6) (26.97) (29.36) C.438 (11.13).250 (6.35) UNEF (73.66) 4.50 (114.0) (30.18) (31.75) C.531 (13.49).312 (7.92) UNEF (63.50) 4.00 (101.6) (30.18) (31.75) C.531 (13.49).312 (7.92) /8-18 UNEF (73.66) 4.69 (119.0) (33.32) (34.14) C.625 (15.88).375 (9.52) /4-18 UNEF (76.20) 4.69 (119.0) (39.67) (37.31) C.750 (19.05).500 (12.70) /8-18 UNEF (76.20) 4.69 (119.0) (39.67) (40.49) C.750 (19.05).500 (12.70) /2-18 UNEF (82.55) 4.90 (124.2) (44.45) (43.66) C.938 (23.83).594 (15.09) /4-18 UN (82.55) 5.13 (130.0) (44.45) (50.01) C.938 (23.83).594 (15.09) UN (91.44) 5.39 (137.0) (57.15) (56.36) C (31.75).938 (23.83) C3106P Potting boot, environmental, less grommet Coupling Thread Class 2B /8-24 UNEF (38.10).969 (24.61).863 (21.92) 12 3/4-20 UNEF (38.10) (26.97).863 (21.92) 12 3/4-20 UNEF (48.41) (26.97).863 (21.92) 14 7/8-20 UNEF (38.10) (29.36).941 (23.90) 14 7/8-20 UNEF (48.41) (29.36).941 (23.90) UNEF (38.10) (31.75) (27.08) UNEF (48.41) (31.75) (27.08) /8-18 UNEF (48.41) (34.14) (30.66) /4-18 UNEF (55.58) (37.31) (33.83) /8-18 UNEF (55.58) (40.49) (37.01) /2-18 UNEF (55.58) (43.66) (40.18) /4-18 UN (55.58) (50.01) (46.53) UN (55.58) (56.36) (52.88) 1. 2 dd.375 for size 0 contacts. X. THED POTTING FO X. X. 9

12 5015 ODE 90 PUG C3108, D, E, F THED X. C3108 Threaded adapter, non-environmental, less grommet C3108E Threaded adapter, environmental, less grommet V THED U Coupling Thread Class 2B U V ccessory Thread Class 2 X 10 5/8-24 UNEF (46.02).969 (24.61).531 (13.49) (25.40) 5/8-24 UNEF 12 3/4-20 UNEF (57.15) (26.97).531 (13.49) (26.97) 5/8-24 UNEF 12 3/4-20 UNEF (50.80) (26.97).531 (13.49) (26.97) 5/8-24 UNEF 14 7/8-20 UNEF (58.72) (29.36).656 (16.66) (28.57) 3/4-20 UNEF 14 7/8-20 UNEF (53.97) (29.36).656 (16.66) (28.57) 3/4-20 UNEF UNEF (65.07) (31.75).750 (19.05) (30.18) 7/8-20 UNEF UNEF (60.32) (31.75).750 (19.05) (30.18) 7/8-20 UNEF /8-18 UNEF (68.28) (34.14).828 (21.03) (33.32) 1-20 UNEF /4-18 UNEF (76.99) (37.31).906 (23.01) (34.92) 1 3/16-18 UNEF /8-18 UNEF (76.99) (40.49).969 (24.61) (34.92) 1 3/16-18 UNEF /2-18 UNEF (86.51) (43.66) (26.19) (39.67) 1 7/16-18 UNEF /4-18 UN (86.51) (50.01) (29.36) (39.67) 1 7/16-18 UNEF UN (95.25) (56.36) (33.32) (47.62) 1 3/4-18 UN THED X. U 3057-* CBE CP C3108D Two (2) piece backshell w/ 3057* clamp, environmental, less grommet C3108F Two (2) piece backshell w/ 3057* clamp, environmental, with grommet Coupling Thread Class 2B U Cable ange Open Closed 10 5/8-24 UNEF (55.58).969 (24.61).516 (13.11) (38.10).312 (7.92).125 (3.18) 12 3/4-20 UNEF (64.29) (26.97).562 (14.27) (38.10).312 (7.92).125 (3.18) 12 3/4-20 UNEF (55.58) (26.97).562 (14.27) (38.10).312 (7.92).125 (3.18) 14 7/8-20 UNEF (68.28) (29.36).625 (15.87) (40.49).438 (11.13).250 (6.35) 14 7/8-20 UNEF (58.72) (29.36).625 (15.87) (40.49).438 (11.13).250 (6.35) UNEF (70.64) (31.75).688 (17.48) (42.88).562 (14.27).312 (7.92) UNEF (61.11) (31.75).688 (17.48) (42.88).562 (14.27).312 (7.92) /8-18 UNEF (72.24) (34.14).750 (19.05) (45.24).625 (15.88).350 (8.89) /4-18 UNEF (82.55) (37.31).844 (21.44) (50.01).750 (19.05).500 (12.70) /8-18 UNEF (82.55) (40.49).906 (23.01) (50.80).750 (19.05).500 (12.70) /2-18 UNEF (94.46) (43.66).953 (24.21) (53.97).938 (23.83).625 (15.88) /4-18 UN (94.46) (50.01) (27.79) (55.58).938 (23.83).625 (15.88) UN (106.38) (56.36) (31.34) (65.89) (31.75).875 (22.23) Plug has O ring under coupling nut. X CBE NGE 10

13 90 PUG C ODE THED X X. U 3057-*C CBE CP C3108 Two (2) piece backshell w/ 3057*C clamp, environmental, less grommet Coupling Thread Class 2B N U Cable Clamp Free Z Cable ange 10 5/8-24 UNEF (55.58).937 (23.80).969 (24.61).516 (13.11) (38.10) C.312 (7.92).094 (2.39) 12 3/4-20 UNEF (64.29).937 (23.80) (26.97).562 (14.27) (38.10) C.312 (7.92).094 (2.39) 12 3/4-20 UNEF (55.58).937 (23.80) (26.97).562 (14.27) (38.10) C.312 (7.92).094 (2.39) 14 7/8-20 UNEF (68.28) (26.97) (29.36).625 (15.87) (40.49) C.438 (11.13).250 (6.35) 14 7/8-20 UNEF (58.72) (26.97) (29.36).625 (15.87) (40.49) C.438 (11.13).250 (6.35) UNEF (70.64) (30.18) (31.75).688 (17.48) (42.88) C.531 (13.49).312 (7.92) UNEF (61.11) (30.18) (31.75).688 (17.48) (42.88) C.531 (13.49).312 (7.92) /8-18 UNEF (72.24) (33.32) (34.14).750 (19.05) (45.24) C.625 (15.88).375 (9.52) /4-18 UNEF (82.55) (39.67) (37.31).844 (21.44) (50.01) C.750 (19.05).500 (12.70) /8-18 UNEF (82.55) (39.67) (40.49).906 (23.01) (50.80) C.750 (19.05).500 (12.70) /2-18 UNEF (94.46) (44.45) (43.66).953 (24.21) (53.97) C.938 (23.83).594 (15.09) /4-18 UN (94.46) (44.45) (50.01) (27.79) (55.58) C.938 (23.83).594 (15.09) UN (106.38) (57.15) (56.36) (31.34) (65.89) C (31.75).938 (23.83) Z CBE NGE N Closed 11

14 EVEE BYONET EVEE BYONET ODEING INFOTION CB W F80 Z9 EIE PEFIX CB eceptacles without wear pins. HE TYE ee Table I below. C ee Table II below. HE IZE 10, 12, 12, 14, 14, 16, 16, 18, 20, 22, 24, 28, 32. INET CONFIGUTION ee pages 27 thru 32 for codes and illustrations. CONTCT TYE P Pin contacts. ocket contacts. TENTE POITION (POIZTION) BN (normal), W, X, Y, Z. ee pages 27 thru 32. ODIFICTION Blank Contacts: older Type upplied. -95 Contacts: Gold Plated per I-G Type II, Class 2 Over Nickel Contacts: Gold Plated per I-G Type II, Class 2 Over Gold Flash per I-G Type I Over Copper Plate per I-C-14550, Class 4. -C2 Chemical Film, per I-C F0 Connector ess Contacts. -F28 Cinch Nut ounting. -F80 WG Crimp Contacts upplied with, but Not Installed in Connector. -H Hex Coupling Nut. - Passivated tainless teel. -Z3 Zinc Nickel Colbalt, Olive Drab. -Z9 Zinc Nickel Colbalt, Black. -1 Electroless Nickel. -11 upplied Unmarked * ess Bushing. -14 upplied ess End Bell. -17 upplied with Gasket for Plug or eceptacle * with Bushing Contacts: Gold Over Nickel. For other codes, contact ales Dept. TBE I. HE TYE tyle Description 00 Wall mount receptacle, front panel mount 030 Wall mount receptacle, rear panel mount 01 In-line receptacle 02 Box mount receptacle, front panel mount 03 Box mount receptacle, rear panel mount 06 traight plug 07 Jam nut receptacle plug TBE II. C Code Class Non-environmental with backshell, less grommet Non-environmental ( 02 and 03) B Environmental with backshell and grommet B Environmental ( 02, 03 and 07) D Non-environmental with cable clamp, less grommet F Environmental with cable clamp and grommet Environmental with cable clamp less grommet Environmental ( 02, 03 and 07) 12

15 W OUNT ECEPTCE FONT PNE OUNT: CB00*, B*, D*, F* EVEE BYONET FONT VIEW IDE VIEW T1 V THED D CB00* Non-environmental, less grommet CB00B* Environmental with grommet Front View ide View T1 D V ±.004 ± [+0.1] [+0.00] in. ± [+0.4] Thread Class [±0.1] [±0.3] [-0.0] [-0.15] [±0.2] [-0.0] [18.20] [25.40].126 [3.20].717 [18.20].323 [8.20].110 [2.80] [43.00].559 [14.20] 5/8-24 UNEF [23.00] [30.00].126 [3.20].969 [24.60].437 [11.10].126 [3.20] [47.00].563 [14.30] 3/4-20 UNEF [24.60] [32.50].126 [3.20] [27.40].563 [14.30].126 [3.20] [47.00].551 [14.00] 7/8-20 UNEF [24.60] [32.50].126 [3.20] [27.40].563 [14.30].126 [3.20] [58.00].748 [19.00] 7/8-20 UNEF [27.00] [35.00].126 [3.20] [30.80].657 [16.70].157 [4.00] [58.00].752 [19.10] 1-20 UNEF [29.40] [38.00].126 [3.20] [34.20].780 [19.80].157 [4.00] [58.00].752 [19.10] 1 3/16-18 UNEF [31.80] [41.00].126 [3.20] [37.40].780 [19.80].157 [4.00] [59.00].748 [19.00] 1 3/16-18 UNEF [34.90] [44.50].146 [3.70] [40.90] [25.40].157 [4.00] [61.00].811 [20.60] 1 7/16-18 UNEF [39.70] [50.80].146 [3.70] [46.70] [27.00].157 [4.00] [67.00].811 [20.60] 1 7/16-18 UNEF [44.50] [57.00].169 [4.30] [53.40] [32.50].157 [4.00] [71.00].874 [22.20] 1 3/4-18 UN FONT VIEW IDE VIEW T1 X Y CB00D* Non-environmental, less grommet CB00F* Environmental with grommet Front View ide View ±.004 [±0.1] ±.012 [±0.3] T [+0.1] [-0.0] T2 Thread etric UNC [+0.00] [-0.15] ±.008 [±0.2] ax [+0.4] [-0.0] X in Y ax [18.20] [25.40].126 [3.20] UNC.717 [18.20].110 [2.80] [64.00].559 [14.20].256 [6.50].894 [22.70] [23.00] [30.00].126 [3.20] UNC.969 [24.60].126 [3.20] [69.00].563 [14.30].354 [9.00] [27.50] [24.60] [32.50].126 [3.20] UNC [27.40].126 [3.20] [71.00].551 [14.00].433 [11.00] [30.00] [24.60] [32.50].126 [3.20] UNC [27.40].126 [3.20] [82.00].748 [19.00].433 [11.00] [30.00] [27.00] [35.00].126 [3.20] UNC [30.80].157 [4.00] [82.00].752 [19.10].559 [14.20] [32.20] [29.40] [38.00].126 [3.20] UNC [34.20].157 [4.00] [82.00].752 [19.10].622 [15.80] [37.50] [31.80] [41.00].126 [3.20] UNC [37.40].157 [4.00] [83.00].748 [19.00].622 [15.80] [37.50] [34.90] [44.50].146 [3.70] UNC [40.90].157 [4.00] [87.00].811 [20.60].843 [21.40] [43.30] [39.70] [50.80].146 [3.70] UNC [46.70].157 [4.00] [93.00].811 [20.60].843 [21.40] [43.30] [44.50] [57.00].169 [4.30] 5 1/4-20UNC [53.40].157 [4.00] [99.00].874 [22.20] [26.70] [51.70] 13

16 EVEE BYONET W OUNT ECEPTCE FONT PNE OUNT: CB00* FONT VIEW T1 IDE VIEW Z CB00* Environmental, less grommet ±.004 [±0.1] Front View ±.012 [±0.3] T [+0.1] [-0.0] [+0.00] [-0.15] ±.008 [±0.2] ax ide View [+0.4] [-0.0] Open Z Closed [18.20] [25.40].126 [3.20].717 [18.20].110 [2.80] [73.00].559 [14.20].312 [7.93].094 [2.38] [23.00] [30.00].126 [3.20].969 [24.60].126 [3.20] [77.00].563 [14.30].438 [11.12].230 [5.84] [24.60] [32.50].126 [3.20] [27.40].126 [3.20] [77.00].551 [14.00].531 [13.48].315 [8.00] [24.60] [32.50].126 [3.20] [27.40].126 [3.20] [88.00].748 [19.00].531 [13.48].315 [8.00] [27.00] [35.00].126 [3.20] [30.80].157 [4.00] [91.00].752 [19.10].625 [15.87].378 [9.60] [29.40] [38.00].126 [3.20] [34.20].157 [4.00] [91.00].752 [19.10].748 [19.00].445 [11.30] [31.80] [41.00].126 [3.20] [37.40].157 [4.00] [92.00].748 [19.00].748 [19.00].445 [11.30] [34.90] [44.50].146 [3.70] [40.90].157 [4.00] [97.00].811 [20.60].937 [23.80].610 [15.50] [39.70] [50.80].146 [3.70] [46.70].157 [4.00] [103.00].811 [20.60].937 [23.80].610 [15.50] [44.50] [57.00].169 [4.30] [53.40].157 [4.00] [113.00].874 [22.20] [31.75].921 [23.40] 14

17 W OUNT ECEPTCE E PNE OUNT: CB030*, B*, D*, F* EVEE BYONET FONT VIEW IDE VIEW T1 V THED D CB030* Non-Environmental, less grommet CB030B* Environmental with grommet ±.004 [±0.1] Front View ±.012 [±0.3] T [+0.1] [-0.0] tyle FP [+0.00] [-0.15] D in. ±.008 [±0.2] ide View ax [+0.4] [-0.0] V Thread Class [18.20] [25.40].126 [3.20].717 [18.20].323 [8.20].110 [2.80] [46.00].717 [18.20] 5/8-24 UNEF [23.00] [30.00].126 [3.20].969 [24.60].437 [11.10].126 [3.20] [50.00].717 [18.20] 3/4-20 UNEF [24.60] [32.50].126 [3.20] [27.40].563 [14.30].126 [3.20] [50.00].717 [18.20] 7/8-20 UNEF [24.60] [32.50].126 [3.20] [27.40].563 [14.30].126 [3.20] [58.00].907 [23.05] 7/8-20 UNEF [27.00] [35.00].126 [3.20] [30.80].657 [16.70].157 [4.00] [58.00].907 [23.05] 1-20 UNEF [29.40] [38.00].126 [3.20] [34.20].780 [19.80].157 [4.00] [58.00].907 [23.05] 1 3/16-18 UNEF [31.80] [41.00].126 [3.20] [37.40].780 [19.80].157 [4.00] [59.00].907 [23.05] 1 3/16-18 UNEF [34.90] [44.50].146 [3.70] [40.90] [25.40].157 [4.00] [59.00].907 [23.05] 1 7/16-18 UNEF [39.70] [50.80].146 [3.70] [46.70] [27.00].157 [4.00] [67.00].947 [24.05] 1 7/16-18 UNEF [44.50] [57.00].169 [4.30] [53.40] [32.50].157 [4.00] [71.00].947 [24.05] 1 3/4-18 UN FONT VIEW T1 IDE VIEW X Y CB030D* Non-Environmental, no grommet CB030F* Environmental with grommet Front View ide View T1 T2 X Y ±.004 ± [+0.1] Thread [+0.00] ±.008 ax [+0.4] in ax [±0.1] [±0.3] [-0.0] etric UNC [-0.15] [±0.2] [-0.0] tyle FP [18.20] [25.40].126 [3.20] UNC.717 [18.20].110 [2.80] [67.0].717 [18.20].256 [6.50].894 [22.70] [23.00] [30.00].126 [3.20] UNC.969 [24.60].126 [3.20] [72.0].717 [18.20].354 [9.00] [27.50] [24.60] [32.50].126 [3.20] UNC [27.40].126 [3.20] [75.0].717 [18.20].433 [11.00] [30.00] [24.60] [32.50].126 [3.20] UNC [27.40].126 [3.20] [82.0].907 [23.05].433 [11.00] [30.00] [27.00] [35.00].126 [3.20] UNC [30.80].157 [4.00] [82.0].907 [23.05].559 [14.20] [32.20] [29.40] [38.00].126 [3.20] UNC [34.20].157 [4.00] [82.0].907 [23.05].622 [15.80] [37.50] [31.80] [41.00].126 [3.20] UNC [37.40].157 [4.00] [83.0].907 [23.05].622 [15.80] [37.50] [34.90] [44.50].146 [3.70] UNC [40.90].157 [4.00] [85.0].907 [23.05].843 [21.40] [43.30] [39.70] [50.80].146 [3.70] UNC [46.70].157 [4.00] [93.0].947 [24.05].843 [21.40] [43.30] [44.50] [57.00].169 [4.30] 5 1/4-20UNC [53.40].157 [4.00] [99.0].947 [24.05] [26.70] [51.70] 15

18 EVEE BYONET W OUNT ECEPTCE E PNE OUNT: CB030* FONT VIEW T1 IDE VIEW Z CB030* Environmental, less grommet ±.004 [±0.1] Front View ±.012 [±0.3] T [+0.1] [-0.0] tyle FP [+0.00] [-0.15] ±.008 [±0.2] ax ide View [+0.4] [-0.0] Open Z Closed [18.20] [25.40].126 [3.20].717 [18.20].110 [2.80] [73.0].717 [18.20].312 [7.93].094 [2.38] [23.00] [30.00].126 [3.20].969 [24.60].126 [3.20] [77.0].717 [18.20].438 [11.12].230 [5.84] [24.60] [32.50].126 [3.20] [27.40].126 [3.20] [77.0].717 [18.20].531 [13.48].315 [8.00] [24.60] [32.50].126 [3.20] [27.40].126 [3.20] [88.0].907 [23.05].531 [13.48].315 [8.00] [27.00] [35.00].126 [3.20] [30.80].157 [4.00] [91.0].907 [23.05].625 [15.87].378 [9.60] [29.40] [38.00].126 [3.20] [34.20].157 [4.00] [91.0].907 [23.05].748 [19.00].445 [11.30] [31.80] [41.00].126 [3.20] [37.40].157 [4.00] [92.0].907 [23.05].748 [19.00].445 [11.30] [34.90] [44.50].146 [3.70] [40.90].157 [4.00] [97.0].907 [23.05].937 [23.80].610 [15.50] [39.70] [50.80].146 [3.70] [46.70].157 [4.00] [103.0].947 [24.05].937 [23.80].610 [15.50] [44.50] [57.00].169 [4.30] [53.40].157 [4.00] [113.0].947 [24.05] [31.75].921 [23.40] 16

19 BOX OUNT ECEPTCE FONT PNE OUNT: CB02*, B* E PNE OUNT: CB03*, B* EVEE BYONET FONT VIEW T1 IDE VIEW THED OPTION N CB02* Non-environmental CB02B* Environmental when used with sealing gasket Front View ide View ±.004 ±.012 T [+0.1] T2 Thread [+0.00] ±.008 ± [+0.4] N ax [±0.1] [±0.3] [-0.0] etric UNC [-0.15] [±0.2] [±0.3] [-0.0] [18.20] [25.40].126 [3.20] UNC.717 [18.20].110 [2.80] [27.60].559 [14.20].638 [16.20] [23.00] [30.00].126 [3.20] UNC.969 [24.60].126 [3.20] [27.60].559 [14.20].756 [19.20] [24.60] [32.50].126 [3.20] UNC [27.40].126 [3.20] [27.60].559 [14.20].882 [22.40] [24.60] [32.50].126 [3.20] UNC [27.40].126 [3.20] [33.80].748 [19.00].882 [22.40] [27.00] [35.00].126 [3.20] UNC [30.80].157 [4.00] [33.80].748 [19.00] [25.60] [29.40] [38.00].126 [3.20] UNC [34.20].157 [4.00] [33.80].748 [19.00] [29.00] [31.80] [41.00].126 [3.20] UNC [37.40].157 [4.00] [33.80].748 [19.00] [32.20] [34.90] [44.50].146 [3.70] UNC [40.90].157 [4.00] [35.80].811 [20.60] [35.30] [39.70] [50.80].146 [3.70] UNC [46.70].157 [4.00] [35.80].811 [20.60] [41.40] [44.50] [57.00].169 [4.30] 5 1/4-20UNC [53.40].157 [4.00] [37.30].874 [22.20] [47.80] FONT VIEW T1 IDE VIEW N CB03* Non-environmental CB03B* Environmental when used with sealing gasket ±.004 [±0.1] Front View ±.012 [±0.3] T [+0.1] [-0.0] tyle 03FP [+0.00] [-0.15] ±.008 [±0.2] ide View ±.012 [±0.3] [+0.4] [-0.0] [18.20] [25.40].126 [3.20].717 [18.20].110 [2.80] [27.60].717 [18.20].638 [16.20] [23.00] [30.00].126 [3.20].969 [24.60].126 [3.20] [27.60].717 [18.20].756 [19.20] [24.60] [32.50].126 [3.20] [27.40].126 [3.20] [27.60].717 [18.20].882 [22.40] [24.60] [32.50].126 [3.20] [27.40].126 [3.20] [33.80].907 [23.05].882 [22.40] [27.00] [35.00].126 [3.20] [30.80].157 [4.00] [34.50].907 [23.05] [25.60] [29.40] [38.00].126 [3.20] [34.20].157 [4.00] [34.50].907 [23.05] [29.00] [31.80] [41.00].126 [3.20] [37.40].157 [4.00] [34.50].907 [23.05] [32.20] [34.90] [44.50].146 [3.70] [40.90].157 [4.00] [35.80].907 [23.05] [35.30] [39.70] [50.80].146 [3.70] [46.70].157 [4.00] [35.80].947 [24.05] [41.40] [44.50] [57.00].169 [4.30] [53.40].157 [4.00] [37.30].947 [24.05] [47.80] N ax 17

20 EVEE BYONET IN-INE ECEPTCE CB01*, B*, D*, F*, * FONT VIEW CB01* Non-environmental, less grommet CB01B* Environmental with grommet IDE VIEW V THED Front View ax [+0.00] [-0.15] D in. ±.008 [±0.2] ide View [+0.4] [-0.0] V Thread Class [22.50].717 [18.20].323 [8.20].110 [2.80] [43.00].559 [14.20] 5/8-24 UNEF [29.50].969 [24.60].437 [11.10].126 [3.20] [47.00].559 [14.20] 3/4-20 UNEF [31.50] [27.40].563 [14.30].126 [3.20] [47.00].559 [14.20] 7/8-20 UNEF [31.50] [27.40].563 [14.30].126 [3.20] [58.00].748 [19.00] 7/8-20 UNEF [34.50] [30.80].657 [16.70].157 [4.00] [58.00].748 [19.00] 1-20 UNEF [37.50] [34.20].780 [19.80].157 [4.00] [58.00].748 [19.00] 1 3/16-18 UNEF [40.50] [37.40].780 [19.80].157 [4.00] [59.00].748 [19.00] 1 3/16-18 UNEF [44.50] [40.90] [25.40].157 [4.00] [61.00].811 [20.60] 1 7/16-18 UNEF D [50.00] [46.70] [27.00].157 [4.00] [67.00].811 [20.60] 1 7/16-18 UNEF [56.50] [53.40] [32.50].157 [4.00] [71.00].874 [22.20] 1 3/4-18 UN CPB01D* Non-environmental, less grommet CPB01F* Environmental with grommet FONT VIEW Front View ax [+0.00] [-0.15] ±.008 [±0.2] ax ide View [+0.4] [-0.0] X in Y ax [22.50].717 [18.20].110 [2.80] [64.0].559 [14.20].256 [6.50].894 [22.70] [29.50].969 [24.60].126 [3.20] [69.0].559 [14.20].354 [9.00] [27.50] [31.50] [27.40].126 [3.20] [71.0].559 [14.20].433 [11.00] [30.00] [31.50] [27.40].126 [3.20] [82.0].748 [19.00].433 [11.00] [30.00] [34.50] [30.80].157 [4.00] [82.0].748 [19.00].559 [14.20] [32.20] [37.50] [34.20].157 [4.00] [82.0].748 [19.00].622 [15.80] [37.50] IDE VIEW [40.50] [37.40].157 [4.00] [83.0].748 [19.00].622 [15.80] [37.50] [44.50] [40.90].157 [4.00] [87.0].811 [20.60].843 [21.40] [43.30] [50.00] [46.70].157 [4.00] [93.0].811 [20.60].843 [21.40] [43.30] [56.50] [53.40].157 [4.00] [99.0].874 [22.20] [26.70] [51.70] X Y FONT VIEW CB01* Environmental, less grommet Front View ax [+0.00] [-0.15] ±.008 [±0.2] ax ide View [+0.4] [-0.0] Open Z Closed [22.50].717 [18.20].110 [2.80] [73.0].559 [14.20].312 [7.93].094 [2.38] [29.50].969 [24.60].126 [3.20] [77.0].559 [14.20].438 [11.12].230 [5.84] [31.50] [27.40].126 [3.20] [77.0].559 [14.20].531 [13.48].315 [8.00] IDE VIEW [31.50] [27.40].126 [3.20] [88.0].748 [19.00].531 [13.48].315 [8.00] [34.50] [30.80].157 [4.00] [91.0].748 [19.00].625 [15.87].378 [9.60] [37.50] [34.20].157 [4.00] [91.0].748 [19.00].748 [19.00].445 [11.30] [40.50] [37.40].157 [4.00] [92.0].748 [19.00].748 [19.00].445 [11.30] [44.50] [40.90].157 [4.00] [97.0].811 [20.60].937 [23.80].610 [15.50] Z [50.00] [46.70].157 [4.00] [103.0].811 [20.60].937 [23.80].610 [15.50] [56.50] [53.40].157 [4.00] [113.0].874 [22.20] [31.75].921 [23.40] 18

21 J NUT ECEPTCE CB07B* EVEE BYONET FONT VIEW T G07 EI/FI COI GOUNDING PING IDE VIEW B T CB07B* Environmental ±.004 [±0.1] Front View ±.012 [±0.3] T [+0.00] [-0.15] B Panel Thickness in. ide View ±.008 [±0.2] [+0.4] [-0.0] V Thread Class [27.00] [31.80].441 [11.20].717 [18.20].094 [2.40].205 [5.20].157 [4.00].965 [24.50] 7/8-20 UNEF [33.00] [41.30].575 [14.60].969 [24.60].094 [2.40].295 [7.50].189 [4.80] [26.80] 1 1/8-18 UNEF [38.10] [44.40].618 [15.70] [27.40].094 [2.40].295 [7.50].189 [4.80] [26.80] 1 1/4-18 UNEF [38.10] [44.40].618 [15.70] [27.40].094 [2.40].295 [7.50].189 [4.80] [32.10] 1 1/4-18 UNEF [39.70] [47.60].661 [16.80] [30.80].094 [2.40].354 [9.00].189 [4.80] [33.70] 1 3/8-18 UNEF [44.00] [50.80].709 [18.00] [34.20].094 [2.40].354 [9.00].189 [4.80] [33.70] 1 1/2-18 UNEF [46.00] [54.20].795 [20.20] [37.40].094 [2.40].358 [9.10].189 [4.80] [33.70] 1 5/8-18 UNEF [50.80] [57.20].795 [20.20] [40.90].094 [2.40].358 [9.10].189 [4.80] [35.20] 1 3/4-18 UNEF [55.00] [63.50].886 [22.50] [46.70].094 [2.40].335 [8.50].220 [5.60] [35.20] 2-18 UN [62.00] [69.80].972 [24.70] [53.40].094 [2.40].256 [6.50].220 [5.60] [35.20] 2 1/4-16 UN V THED O'ING 19

22 EVEE BYONET TIGHT PUG CB06*, B*, D*, F*, * FONT VIEW IDE VIEW V THED CB06* Non-environmental, less grommet CB06B* Environmental with grommet Front View ide View D ax D in. V Thread Class [22.80].323 [8.20] [47.00] 5/8-24 UNEF [29.20].437 [11.10] [47.00] 3/4-20 UNEF [33.00].563 [14.30] [47.00] 7/8-20 UNEF [33.00].563 [14.30] [58.00] 7/8-20 UNEF [36.50].657 [16.70] [58.00] 1-20 UNEF [39.90].780 [19.80] [58.00] 1 3/16-18 UNEF [43.10].780 [19.80] [59.00] 1 3/16-18 UNEF [46.60] [25.40] [61.00] 1 7/16-18 UNEF [53.40] [27.00] [67.00] 1 7/16-18 UNEF [60.10] [32.50] [71.00] 1 3/4-18 UN FONT VIEW IDE VIEW CB06D* Non-environmental, less grommet CB06F* Environmental with grommet X Y Front View ax ax ide View X in Y ax [22.80] [64.00].256 [6.50].894 [22.70] [29.20] [69.00].354 [9.00] [27.50] [33.00] [71.00].433 [11.00] [30.00] [33.00] [82.00].433 [11.00] [30.00] [36.50] [82.00].559 [14.20] [32.20] [39.90] [82.00].622 [15.80] [37.50] [43.10] [83.00].622 [15.80] [37.50] [46.60] [87.00].843 [21.40] [43.30] [53.40] [93.00].843 [21.40] [43.30] [60.10] [99.00] [26.70] [51.70] FONT VIEW IDE VIEW CB06* Environmental, less grommet Z Front View ide View Z ax ax Open Closed [22.80] [73.00].312 [7.93].094 [2.38] [29.20] [77.00].438 [11.12].230 [5.84] [33.00] [77.00].531 [13.48].315 [8.00] [33.00] [88.00].531 [13.48].315 [8.00] [36.50] [91.00].625 [15.87].378 [9.60] [39.90] [91.00].748 [19.00].445 [11.30] [43.10] [92.00].748 [19.00].445 [11.30] [46.60] [97.00].937 [23.80].610 [15.50] [53.40] [103.00].937 [23.80].610 [15.50] [60.10] [113.00] [31.75].921 [23.40] 20

23 90 PUG CB08*, B*, D*, F*, * EVEE BYONET CB08* CB08B* Non-environmental, less grommet Environmental with grommet FONT VIEW IDE VIEW 1 Front View ax 1 ax 2 ax ide View V Thread Class 2 W in [22.80] [45.00] [30.00] 5/8-24 UNEF.335 [8.50] [29.20] [47.00] [30.00] 3/4-20 UNEF.472 [12.00] [32.00] [48.00] [30.00] 7/8-20 UNEF.571 [14.50] [32.00] [57.00] [30.00] 7/8-20 UNEF.571 [14.50] [36.50] [58.00] [35.00] 1-20 UNEF.689 [17.50] [39.90] [61.00] [35.00] 1 3/16-18 UNEF.768 [19.50] [43.10] [61.00] [35.00] 1 3/16-18 UNEF.866 [22.00] [46.60] [66.00] [40.00] 1 7/16-18 UNEF.984 [25.00] V THED W [53.40] [66.00] [40.00] 1 7/16-18 UNEF [29.00] [60.10] [72.00] [45.00] 1 3/4-18 UN [34.00] CB08D* Non-environmental, less grommet CB08F* Environmental with grommet FONT VIEW IDE VIEW 1 Front View ide View 1 3 X Y ax ax ax in ax [22.80] [45.00] [42.00].256 [6.50].894 [22.70] [29.20] [47.00] [42.00].354 [9.00] [27.50] [32.00] [48.00] [45.00].433 [11.00] [30.00] [32.00] [57.00] [45.00].433 [11.00] [30.00] [36.50] [58.00] [53.00].559 [14.20] [32.20] [39.90] [61.00] [53.00].622 [15.80] [37.50] [43.10] [61.00] [53.00].622 [15.80] [37.50] [46.60] [66.00] [58.00].843 [21.40] [43.30] [53.40] [66.00] [58.00].843 [21.40] [43.30] [60.10] [72.00] [66.00] [26.70] [51.70] X Y CB08* Environmental, less grommet Front View ide View 1 Z ax ax Open Closed [22.80] [45.00].312 [7.93].094 [2.38] FONT VIEW IDE VIEW [29.20] [47.00].438 [11.12].230 [5.84] [32.00] [48.00].531 [13.48].315 [8.00] [32.00] [57.00].531 [13.48].315 [8.00] [36.50] [58.00].625 [15.87].378 [9.60] [39.90] [61.00].748 [19.00].445 [11.30] [43.10] [61.00].748 [19.00].445 [11.30] [46.60] [66.00].937 [23.80].610 [15.50] [53.40] [66.00].937 [23.80].610 [15.50] [60.10] [72.00] [31.75].921 [23.40] Z 21

24 ODNNCE ODNNCE EECTIC CONNECTO GENE DECIPTION For maximum standardization, both in procurement and field service, the Ordnance Department has limited the shell types, sizes and insert arrangements to those found on Ordnance Procurement Chart This catalog section contains the electrical connectors and accessories available from Crown Connector and appear on the chart. Crown Ordnance Connectors include: 1. esilient inserts per Ordnance pecifications provide high dielectric strength, high arc resistance and resistance to severe vibration. 2. luminum components are fabricated to withstand vibration and shock. 3. Components come with a cadmium plate finish and a clear chromate after treatment. This finish is electrically conductive and is resistant to corrosion. 4. High quality copper alloy contacts are silver plated to assure good electrical continuity between pins and socket contacts. 5. atisfactory performance through a temperature range of -65 F to +257 F. ODNNCE INET NGEENT & Contact Total Contacts Insert ervice ating D Inst D E D = E Bal = H = D Bal = D G = D Bal = D = E Bal = D D ODNNCE CONNECTO OUCE Ordnance Description Crown P/N mphenol Cap Grommet eceptacle CC P P eceptacle CC eceptacle CC P P eceptacle CC eceptacle CC P P eceptacle CC eceptacle CC P P eceptacle CC eceptacle CC P P eceptacle CC eceptacle CC P P eceptacle CC eceptacle eceptacle CC Gaskets Grommet Grommet Coupling Nut Type II eceptacle CC P P Coupling Nut Plug CC P P Plug CC Plug CC P P Plug CC Plug CC P P Plug CC Plug CC P P Plug CC Plug CC P P Plug CC Plug CC P P Plug CC Plug CC P P Plug CC Cap Cap Cap ignal Corp. No. -C eceptacle CC D Plug CC P P C-D Plug CC D Plug CC P P -C dapter CC

25 BOX OUNTING ECEPTCE ODNNCE ± ±.005 Ø IZE ± ± NEF THED C IN. FU THED * ± * X. Insert rrangement Order Number 22-2P P P P P P P TIGHT PUG BODY Insert rrangement Order Number 22-2P IZE * ± P P P P P P Ø ± NEF THED C 2 ODNNCE GOET.438 ± Order Number Insert rrangement Contact ty

26 ODNNCE ODNNCE COUPING NUT The three coupling nut styles illustrated represent one of the types used to complete an Ordnance ssembly. In all cases; they must be assembled to its respective assembly, prior to soldering operations. IZE 22 TYPE I Ø1.612 EF NEF THED C EF..703 EF. TYPE II EF NEF THED C 2 TYPE III Ø1.612 EF. Ø Order Number: Ø1.612 EF. GET FO IZE 22 ECEPTCE ±.005 PIN ± ±.010 The Crown Flat Flange Gasket of synthetic rubber material is provided to further complete the moistureproofing and pressure sealing features of Crown connectors. It is for use with flange mounting receptacles ±.010 Order Number:

27 ECEPTCE POTECTION CP ODNNCE.754 X. FO IZE 22 ECEPTCE Ø (Use with wall and box mounting receptacles) NEF THED C CHIN ENGTH Order Number: This assembly provides for a moisture-proof, dust proof sealing for the receptacle when unmated. Chain and eyelet provide permanent attachment under the mounting bolt of the receptacle assembly. HI-TENION ECEPTCE ± ± X UNEF THED C X. Ø Ø.594 ± ± ±.005 Ø.719 ±.010 Order Number: X..391 IN X..770 X X. This receptacle, together with its mating plug, is designed to withstand a 17.7 VC rms potential at 60 CP for one minute, using JN G-8/U cable (or equivalent). Protection from vibration is ensured through the dampening action of the Crown resilient insert and the strength of special alloy aluminum shells. 25

28 ODNNCE ENVIONENT DPTE -C C1000 DPTE FO IZE 22 CONNECTO UNEF THED The C1000 dapter is designed as a functional equivalent to the -C This new design has incorporated the six component parts and eight groups of the ignal Corp. dapter into only three component parts and three groups. ome advantages offered by the C1000 are: reductions in cost, overall length, weight and a reduction in the number of parts that are subject to corrosion. rmy Electronics Command Cable ange ODNNCE CO EFEENCE Crown Catalog Crown P/N Cable ange unbank mphenol Ordnance C1000-GP C-D GP C1000-GP C-D GP C1000-GP C-D GP C1000-GP C-D GP C1000-GP C-D GP C1000-GP C-D GP C1000-GP C-D GP C1000-GP C-D GP C1000-GP

29 B 5015 INET CONFIGUTION INET CONFIG. TENTE POITION (POIZTION) The diagrams indicate alternate insert positions. The four positions (W, X, Y, and Z) differ in degree of rotation for various sizes and layouts. NO POITION 100 B B B B B B B POITION N POITION W POITION X POITION Y POITION Z POITION 1 POITION B B B 250 B 280 B B POITION 3 POITION 4 POITION 5 POITION 8 POITION 9 POITION 12 POITION 13 ENGGING FCE OF PIN INET HOWN OCET INET E IO IGE Part Number Total Contacts lternate Positions (Degrees) W X Y Z emarks Position = 180º Position 12 of Position 13 of ame as Non-ilitary Positions W=90º Non-ilitary Positions W=80º Use eplaces: 147, Position 12 of Position 13 of Position 12 of Position 2 of Position 12 of = ilitary designation per I-TD-1651 = ilitary designation inactive for new design. CONTINUED ON NEXT PGE 27

30 INET CONFIG INET CONFIGUTION Part Number Total CONTINUED FO PEVIOU PGE Contacts lternate Positions (Degrees) W X Y Z emarks Position 3 of Position 12 of Position 13 of Use High voltage Deg otation To ight of Deg otation To ight of Position 12 of Position 13 of Position 12 of Position 13 of Position 12 of Position 13 of Position 3 of Position 2 of Position 5 of ame as = ilitary designation per I-TD-1651 = ilitary designation inactive for new design. CONTINUED ON NEXT PGE 28

31 5015 INET CONFIGUTION INET CONFIG. Part Number Total Contacts 16 CONTINUED FO PEVIOU PGE lternate Positions (Degrees) W X Y Z emarks 20B ame as Position 12 of Position 13 of Position 2 of Non-ilitary Positions Z=280º ame as = ilitary designation per I-TD-1651 = ilitary designation inactive for new design. CONTINUED ON NEXT PGE 29

32 INET CONFIG INET CONFIGUTION Part Number Total CONTINUED FO PEVIOU PGE Contacts lternate Positions (Degrees) W X Y Z emarks B Position 12 of Position 12 of Position 2 of G Use 24C C Use Use Position 12 of horting type = ilitary designation per I-TD-1651 = ilitary designation inactive for new design. CONTINUED ON NEXT PGE 30

33 5015 INET CONFIGUTION INET CONFIG. Part Number Total Contacts lternate Positions (Degrees) W X Y Z emarks Position 13 of Position 12 of Position 13 of Position 12 of B Use Position 12 of = ilitary designation per I-TD-1651 = ilitary designation inactive for new design. CONTINUED FO PEVIOU PGE CONTINUED ON NEXT PGE 31

34 INET CONFIG INET CONFIGUTION Part Number Total Contacts 16 CONTINUED FO PEVIOU PGE lternate Positions (Degrees) W X Y Z emarks /0 Contact Use Position 12 of Position 12 of Position 2 of Position 2 of B otation of Deg otation of * = ilitary designation per I-TD-1651 = ilitary designation inactive for new design. CONTINUED ON NEXT PGE 32

35 5015 CONTCT CCE OIE TBE I. CONTCT NGEENT EVICE TING ervice ating ecommended Operating Voltage* t ea evel Effective Creepage Distance Nom. echanical pacing Nom. DC C () Inst / /8 1/16 D /16 1/8 E /4 3/16 B /16 1/4 C /16 EECTIC EVICE DT Test current ratings of contacts and allowable voltage drop under test conditions when assembled as in service are shown below. aximum total current to be carried per connector is the same as the allowable in wire bundles as specified in I-W ervice ating irspace Nominal Distance TITUDE VOTGE DETING** CHT Creepage tandard ea evel Conditions inimum Flashover Voltage C () Test Voltage C () Pressure ltitude 50,000 Feet inimum Flashover Voltage C () Test Voltage C () Pressure ltitude 70,000 Feet inimum Flashover Voltage C () Test Voltage C () Inst. 1/32 1/ /16 1/ D 1/8 3/ E 3/16 1/ B 1/4 5/ C 5/ Not corrected for changes in density due to variations in temperature. ** No attempt has been made to recommend operating voltages. The designer must determine his own operating voltage by the application of a safety factor to the above derating chart to compensate for circuit transients, surges, etc. Contact CONTCT TING Wire ated Current Potential Drop ax Current 16 & WG mv WG mv WG mv WG mv WG mv

36 CCE OIE 5015 ODE CONTCT ODE CONTCT CUENT TING* ating End Wire Barrel llowable Wire Test Current** mps 16/ ØB Ø ODE CUP DIENION B Contact in.069 [1.75].112 [2.84].205 [5.20].328 [8.33].464 [11.78] Dimensions are in Inches [mm].096/.116 [2.43/2.94].130/.150 [3.30/3.81].243/.259 [6.17/6.57].370/.397 [9.39/10.08].510/.550 [12.95/13.97].250/.313 [6.35/7.95].375/.438 [9.52/11.12].500/.563 [12.70/14.30].625/.688 [15.87/17.47].625/.688 [15.87/17.47] TBE II. WIE NGE CCOODTION Contact Wire older Contact Connectors O.D. Of Finished Wire (Inch) Crimp Contact Connectors Front elease ear elease in ax in ax in ax.064 [1.63].114 [2.90].164 [4.17].272 [6.91].415 [10.54].130 [3.30].170 [4.32].255 [6.48].370 [9.40].550 [13.97] 0.66 [1.68].097 [2.46].132 [3.35].237 [6.02].360 [9.14].130 [3.30].170 [4.32].255 [6.48].370 [9.40].550 [13.97].053 [1.35].085 [2.16].132 [3.35].237 [6.02].360 [9.14].103 [2.62].158 [4.01].255 [6.48].370 [9.40].550 [13.97] Dimensions are in Inches [mm] * older Wells Filled ** Contact ratings as stated are test ratings only. The connector could not withstand full rated current through all contacts continuously. Please note that the electrical data given is not an establishment of electrical safety factors. This is left entirely in the designer's hands as he can best determine which peak voltage, switching surges, transients, etc, can be expected in a particular circuit. Pin 5015 EIE I ODE CONTCT Pin Filled older Cup (Note 1) ocket (Note 1) ocket Filled older Cup (Note 1) aterial Finish 16 P P Note 2 ilver 16 P P Note 2 ilver 12 P P Note 2 ilver 8 P P Note 2 ilver 4 P P Note 2 ilver 1/0 P P Note 2 ilver Note 1: Only 3100 thru 3108 and connectors are supplied with solder filled cups Note 2: Pins are brass; ockets are copper. 34

37 5015 CIP CONTCT PIN F80 CCE OIE EIE PEFIX crimp F80 pin contact. CONTCT IZE CODE IZE /0 WIE NGE ee Table below. ODIFICTION Consult ales Department. TEI/FINIH 110 Copper/silver. 140 Copper/gold. 142 Copper/gold aterial: Copper Finish: ilver ØD ØC Ø ØB Part Number For Wire WG mm 2 B C D [0.45].077 [1.95].062 [1.58].126 [3.20] [31.75] [.085].061 [1.55].062 [1.58].126 [3.20] [31.75] [130].076 [193].062 [158].126 [3.20] [31.75] [1.20].102 [2.60].062 [158].126 [3.20] [31.75] [150].102 [2.60].062 [158].126 [3.20] [31.75] [1.70].102 [2.60].062 [158].126 [3.20] [31.75] [2.00].115 [2.90].062 [158].126 [3.20] [31.75] [2.50].150 [3.80].062 [1.58].126 [3.20] [31.75] [130].076 [193].062 [158].126 [3.20] [26.65] [120].102 [2.60].062 [158].126 [3.20] [26.65] [150].102 [2.60].062 [158].126 [3.20] [26.65] [170].102 [2.60].062 [158].126 [3.20] [26.65] [2.00].115 [2.90].062 [158].126 [3.20] [26.65] [2.50].150 [3.80].062 [1.58].126 [3.20] [26.65] [1.20].102 [2.60].093 [2.38].189 [4.80] [37.65] [1.50].134 [3.40].093 [2.38].189 [4.80] [37.65] [2.00] 1.50 [3.80].093 [2.38].189 [4.80] [37.65] [2.20].150 [3.80].093 [2.38].189 [4.80] [37.65] [2.50].154 [3.90].093 [2.38].189 [4.80] [37.65] [3.00].176 [4.80].093 [2.38].189 [4.80] [37.65] [3.30].166 [4.20].093 [2.38].189 [4.80] [37.65] [3.60].176 [4.80].093 [2.38].189 [4.80] [37.65] [4.50].272 [6.90].093 [2.38].189 [4.80] [37.65] [1.50].134 [3.40].141 [3.59].307 [7.80] [40.70] [1.80].150 [3.80].141 [3.59].307 [7.80] [40.70] [2.50].154 [3.90].141 [3.59].307 [7.80] [40.70] [3.00].176 [4.80].141 [3.59].307 [7.80] [40.70] [4.50].272 [6.90].141 [3.59].307 [7.80] [40.70] [5.00].272 [6.90].141 [3.59].307 [7.80] [40.70] [5.80].307 [7.80].141 [3.59].307 [7.80] [40.70] [2.20].150 [3.80].225 [5.70].433 [11.00] [41.25] [2.50].150 [3.80].225 [5.70].433 [11.00] [41.25] [3.00].189 [4.80].225 [5.70].433 [11.00] [41.25] [5.00].275 [7.00].225 [5.70].433 [11.00] [41.25] [6.20].374 [9.50].225 [5.70].433 [11.00] [41.25] [7.10].375 [9.53].225 [5.70].433 [11.00] [41.25] [7.80].374 [9.50].225 [5.70].433 [11.00] [41.25] [9.00].565 [14.35].225 [5.70].433 [11.00] [41.25] / [4.55].268 [6.80].356 [9.05].595 [15.11] [46.50] / [5.00].275 [7.00].356 [9.05].595 [15.11] [46.50] / [7.15].375 [9.53].356 [9.05].595 [15.11] [46.50] / [7.80].374 [9.50].356 [9.05].595 [15.11] [46.50] / [9.00].565 [14.35].356 [9.05].595 [15.11] [46.50] / [10.70].565 [14.35].356 [9.05].595 [15.11] [46.50] /0 1/ [11.50].565 [14.35].356 [9.05].595 [15.11] [46.50] Dimensions in brackets [ ] are in millimeters. 35

38 CCE OIE 5015 CIP CONTCT OCET F80 T EIE PEFIX T crimp F80 socket contact. CONTCT IZE CODE IZE /0 * Indicates closed entry socket. WIE NGE ee Table below. ODIFICTION Consult ales Department. TEI/FINIH 110 Copper/silver. 140 Copper/gold. 142 Copper/gold * Copper/silver. 540* Copper/gold. 542* Copper/gold * pplies only to socket contact sizes 8, 4, 1/0 and 4/0 Part Number For Wire WG mm 2 B C D T [0.45].077 [1.95].065 [1.65].126 [3.20] [36.50] T [0.85].061 [1.55].065 [1.65].126 [3.20] [36.50] T [1.30].076 [1.93].065 [1.65].126 [3.20] [36.50] T [1.20].102 [2.60].065 [1.65].126 [3.20] [36.50] T [1.50].102 [2.60].065 [1.65].126 [3.20] [36.50] T [1.70].102 [2.60].065 [1.65].126 [3.20] [36.50] T [2.00].115 [2.90].065 [1.65].126 [3.20] [36.50] T [2.50].150 [3.80].065 [1.65].126 [3.20] [36.50] T [1.30].076 [1.93].065 [1.65].126 [3.20] [26.65] T [1.20].102 [2.60].065 [1.65].126 [3.20] [26.65] T [1.50].102 [2.60].065 [1.65].126 [3.20] [26.65] T [1.70].102 [2.60].065 [1.65].126 [3.20] [26.65] T [2.00].115 [2.90].065 [1.65].126 [3.20] [26.65] T [2.50].150 [3.80].065 [1.65].126 [3.20] [26.65] T [1.20].102 [2.60].098 [2.48].189 [4.80] [37.65] T [1.50].134 [3.40].098 [2.48].189 [4.80] [37.65] T [2.00].150 [3.80].098 [2.48].189 [4.80] [37.65] T [2.20].150 [3.80].098 [2.48].189 [4.80] [37.65] T [2.50].154 [3.90].098 [2.48].189 [4.80] [37.65] T [3.00].176 [4.80].098 [2.48].189 [4.80] [37.65] T [3.30].166 [4.20].098 [2.48].189 [4.80] [37.65] T [3.60].176 [4.80].098 [2.48].189 [4.80] [37.65] T [4.50].272 [6.90].098 [2.48].189 [4.80] [37.65] T [1.50].134 [3.40].147 [3.73].307 [7.80] [40.50] T [1.80].150 [3.80].147 [3.73].307 [7.80] [40.50] T [2.50].154 [3.90].147 [3.73].307 [7.80] [40.50] T [8.00].176 [4.80].147 [3.73].307 [7.80] [40.50] T [4.50].272 [6.90].147 [3.73].307 [7.80] [40.50] T [5.00].272 [6.90].147 [3.73].307 [7.80] [40.50] T [5.80].307 [7.80].147 [3.73].307 [7.80] [40.50] T [2.20].150 [3.80].230 [5.84].433 [11.00] [41.25] T [2.50].150 [3.80].230 [5.84].433 [11.00] [41.25] T [3.00].189 [4.80].230 [5.84].433 [11.00] [41.25] T [5.00].275 [7.00].230 [5.84].433 [11.00] [41.25] T [6.20].374 [9.50].230 [5.84].433 [11.00] [41.25] T [7.15].375 [9.50].230 [5.84].433 [11.00] [41.25] T [7.80].374 [9.50].230 [5.84].433 [11.00] [41.25] T [9.00].565 [14.35].230 [5.84].433 [11.00] [41.25] T / [4.55].268 [6.80].365 [9.20].595 [15.11] [46.50] T / [5.00].275 [7.00].365 [9.20].595 [15.11] [46.50] T / [7.15].375 [9.53].365 [9.20].595 [15.11] [46.50] T / [7.80].374 [9.50].365 [9.20].595 [15.11] [46.50] T / [9.00].565 [14.35].365 [9.20].595 [15.11] [46.50] T / [10.70].565 [14.35].365 [9.20].595 [15.11] [46.50] T /0 1/ [11.50].565 [14.35].365 [9.20].595 [15.11] [46.50] Dimensions in brackets [ ] are in millimeters. aterial: Copper Finish: ilver ØD ØC Ø ØB 36

39 INETION, EOV ND CIP TOO F80 CIP CONTCT 5015 EIE CCE OIE anual Crimp Tool Frame Pico Tools odel 300 Contact Wire Insertion emoval Guide Tool Tool it Pins /1-01 (wg) Die Part No. P/N ocator ocator (Note 2) ocator Part No. Pico Tools odel 400-BHD Die Part No. (Note 2) ocator Part No. Pico Tools odel 500-D Die Part No. (Note 2) * 16 Pin T T TH378* 314D-16 C17P 414D-16N D-16N T * 16 kt T T T TH378* 314D-16 C17 414D-16N D-16N * 16 Pin T T D-22N 9633 T * 16 kt T T T D-22N * 16 Pin 20 T T D-16N D-16N T * 16 kt 20 T T T D-16N D-16N * 16 Pin T T TH378* 314D-20 C17P 414D-16N D-16N T * 16 kt T T T TH378* 314D-20 C17 414D-16N D-16N * 16 Pin 18 T T TH378* 314D-20 C17P 414D-16N D-16N T * 16 kt 18 T T T TH378* 314D-20 C17 414D-16N D-16N * 16 Pin 14 T T TH378* 314D-16 C17P 414D-16N D-16N T * 16 kt 14 T T T TH378* 314D-16 C17 414D-16N D-16N * 16 Pin 12 T T TH378* 314D-12 C17P 414D-12N D-12N T * 16 kt 12 T T T TH378* 314D-12 C17 414D-12N D-12N * 16 Pin T T D-16N D-16N T * 16 kt T T T D-16N D-16N * 16 Pin T T TH379* 314D-16 C16P 414D-16N D-16N T * 16 kt T T T TH379* 314D-16 C16 414D-16N D-16N * 16 Pin 20 T T TH379* 314D-20 C16P 414D-16N D-16N T * 16 kt 20 T T T TH379* 314D-20 C16 414D-16N D-16N * 16 Pin T T D-20N D-20N T * 16 kt T T T D-20N D-20N * 16 Pin 18 T T D-16N D-16N T * 16 kt 18 T T T D-16N D-16N * 16 Pin 14 T T TH379* 314D-16 C16P 414D-16N D-16N T * 16 kt 14 T T T TH379* 314D-16 C16 414D-16N D-16N * 16 Pin 12 T T D-18N D-18N T * 16 kt 12 T T T D-18N D-18N * 12 Pin 12 T T TH378* 414D-12N D-12N T * 12 kt 12 T T T TH378* 414D-12N D-12N * 12 Pin 8 T T D-6N D-6N T * 12 kt 8 T T T D-6N D-6N * 12 Pin 20 T T D-16N D-16N T * 12 kt 20 T T T D-16N D-16N * 12 Pin 18 T T TH378* 414D-16N D-16N T * 12 kt 18 T T T TH378* 414D-16N D-16N * 12 Pin T T D-10N D-10N T * 12 kt T T T D-10N D-10N * 12 Pin 2.5mm 2 T T D-8N D-8N T * 12 kt 2.5mm 2 T T T D-8N D-8N * 12 Pin 4.0mm 2 T T D-10N D-10N T * 12 kt 4.0mm 2 T T T D-10N D-10N * 12 Pin 4.0mm 2 T D-10N D-10N T * 12 kt 4.0mm 2 T T D-18N D-18N * 12 Pin 6.0mm 2 T D-10N D-10N T * 12 kt 6.0mm 2 T T D-10N D-10N Note 1. Consult sales department. Note 2. Pico Tools Die part numbers ending in letter N are for an 8 indent crimp. For Hex crimp, change letter N to HEX. * Indicates additional alpha-numerics are required to complete part number. ocators provided by stro Tool. ocator Part No. CONTINUED ON NEXT PGE 37

40 CCE OIE INETION, EOV ND CIP TOO F80 CIP CONTCT 5015 EIE CONTINUED FO PEVIOU PGE anual Crimp Tool Frame Pico Tools odel 300 Contact Wire Insertion emoval Guide Tool Tool it Pins /1-01 (wg) Die Part No. P/N ocator ocator (Note 2) * 8 Pin 8 T T ocator Part No. Pico Tools odel 400-BHD Die Part No. (Note 2) ocator Part No. Pico Tools odel 500-D Die Part No. (Note 2) * 8 Pin 18 T T Not 414D-12N D-12N T * 8 kt 18 T T equired 414D-12N D-12N ocator Part No. 414D-6N D-6N T * 8 kt 8 T T D-6N D-6N * 8 Pin T T D-18N D-18N T * 8 kt T T D-18N D-18N * 8 Pin 12 T T D-18N D-18N T * 8 kt 12 T T D-18N D-18N * 8 Pin 4.0mm 2 T T D-10N D-10N T * 8 kt 4.0mm 2 T T Not 414D-10N D-10N * 8 Pin 10.0mm 2 T T equired 414D-8N D-8N T * 8 kt 10.0mm 2 T T D-8N D-8N * 8 Pin 6 Note 1 T D-6N D-6N T * 8 kt 6 Note 1 T D-6N D-6N * 4 Pin 4 T T D-4N D-4N T * 4 kt 4 T T D-4N D-4N * 4 Pin 2.5mm 2 T T D-18N D-18N T * 4 kt 2.5mm 2 T T D-18N D-18N * 4 Pin 25.0mm 2 T T D-4N D-4N T * 4 kt 25.0mm 2 T T D-4N D-4N * 4 Pin 12 T T D-10N D-10N T * 4 kt 12 T T Not 414D-10N D-10N * 4 Pin 4.0mm 2 T T equired 414D-10N D-10N T * 4 kt 4.0mm 2 T T D-10N D-10N * 4 Pin 35.0mm 2 T T D-0N D-0N T * 4 kt 35.0mm 2 T T D-0N D-0N * 4 Pin 10.0mm 2 T T D-8N D-8N T * 4 kt 10.0mm 2 T T D-8N D-8N * 4 Pin 16.0mm 2 T T D-4N D-4N T * 4 kt 16.0mm 2 T T D-4N D-4N * 1/0 Pin 1/0 T T D-0N D-0N T * 1/0 kt 1/0 T T D-0N D-0N * 1/0 Pin 25.0mm 2 T T D-4N D-4N T * 1/0 kt 25.0mm 2 T T D-4N D-4N * 1/0 Pin 35.0mm 2 T T D-0N D-0N T * 1/0 kt 35.0mm 2 T T D-0N D-0N * 1/0 Pin 8 T T Not 414D-6N D-6N T * 1/0 kt 8 T T equired 414D-6N D-6N * 1/0 Pin 4 Note 1 T D-4N D-4N T * 1/0 kt 4 Note 1 T D-4N D-4N * 1/0 Pin 10.0mm 2 T T D-4N D-4N T * 1/0 kt 10.0mm 2 T T D-4N D-4N * 1/0 Pin 50.0mm 2 T T D-0N D-0N T * 1/0 kt 50.0mm 2 T T D-0N D-0N Note 1. Consult sales department. Note 2. Pico Tools Die part numbers ending in letter N are for an 8 indent crimp. For Hex crimp, change letter N to HEX. * Indicates additional alpha-numerics are required to complete part number. ocators provided by stro Tool. 38

41 INETION ND EOV TOO F80 CIP CONTCT CCE OIE Contact pacecraft stro Tool Bendix TENTE INETION TOO ITT Cannon Commital Daniels Veam 16 T TBX CIT-F D T TBX CIT-F D T TBX CIT D T50 4 T TC * CIT T50 1/0 T * CIT T50 * equires rbor Press Contact TENTE EOV TOO pacecraft stro Tool Bendix 16 T TBX (it) 12 T TBX (it) ITT Cannon CET- F80-16 CET- F80-12 Commital Daniels Veam D D T TBX (it) CET D T TC2234 1/0 T * equires rbor Press P= * = * P= * = * CET CET Contact pacecraft TENTE GUIDE PIN Bendix ITT Cannon Commital Veam 16 T Unknown T50 12 T Unknown T50 8 T Unknown Not equired Not equired 4 Not equired Not equired Not equired Not equired Not equired 1/0 Not equired Not equired Not equired Not equired Not equired 39

42 CCE OIE CBE CP 3057-*, C BUHING EE TBE (NOT UPPIED) POVIION I DE FO FETYING HOE 3057-* 3057-*W E G I PEC N DH NUBE ee Dimension Table below. TYPE Non-environmental. W Clamp is supplied with a rubber gasket and fiber washer. FINIH Blank Cadmium, olive drab 48 hr. salt spray Cadmium, olive drab over suitable underplate, 1000 hr. salt spray N Electroless nickel aterial: luminum alloy Note: Bushing can be "telescoped" to achieve a smaller sealing diameter. Dash No. Connector (ef) Thread Class 2B B ax Øe ±.031 (±0.79) F ±.031 (±0.79) G ±.031 (±0.79) Bushing (ef) () -3 8 & UNEF.250 (6.35).688 (17.48).812 (20.62) (20.62) -4 10, 12 & UNEF.312 (7.92).812 (20.62).875 (22.22) F & UNEF.438 (11.13).969 (24.61) (26.97).875 (22.22) & UNEF.562 (14.27) (27.79) (29.36) UNEF.625 (15.87) (30.18) (31.75).938 (23.83) & UNEF.750 (19.05) (34.92) (37.31) & UNEF.938 (23.83) (42.06) (42.88) (26.19) UN (31.75) (51.59) (51.59) (27.79) UN (34.92) (56.36) (57.94) (29.36) UN (41.27) (63.50) (68.28) (42.88) CEW-FIITE HED WITH WHE ØB UN (47.62) (70.64) (74.63) (44.45) UN (60.32) (83.34) (88.90) Dimensions are shown in Inches (mm. (a) Telescoping bushings are not supplied with clamps *C C CPING B E I PEC DH NUBE ee Dimension Table below. TYPE C Cable sealing. FINIH Blank Cadmium, olive drab 48 hr. salt spray Cadmium, olive drab over suitable underplate, 1000 hr. salt spray N Electroless nickel aterial: luminum alloy BODY C F Dash No. Conn. (ef) C ax E ax Closed F ( ) ax V Thread Class 2B Øz pprox. (Gland) Free Closed Bushing (ef) () -3 8 & (20.62).217 (5.51).231 (5.87) (34.92) UNEF.219 (5.56).031 (0.79) , 12 & (23.80).296 (7.52).315 (8.00) (34.92) UNEF.312 (7.92).094 (2.39) EEVE GND Z V & (26.97).390 (9.91).440 (11.18) (34.92) UNEF.438 (11.13).250 (6.35) & (30.18).515 (13.08) (34.92) UNEF.531 (13.49).312 (7.92) (11.02) (33.32).614 (15.60) (36.50) UNEF.625 (15.87).375 (9.52) & (39.67).738 (18.75) (36.50) UNEF.750 (19.05).500 (12.70) (15.14) & (44.45).926 (23.52) (39.67) UNEF.938 (23.83).594 (15.09) (57.15) (30.48) (46.02) UN (31.75).938 (23.83) (21.79) (60.32) (34.62) (46.02) UN (34.92).969 (24.61) (66.67) (28.12) (40.92) (52.37) UN (41.27) (30.18) (71.42) (36.09) (47.37) (55.58) UN (47.62) (34.92) (a) Telescoping bushings are not supplied with clamps. 40

43 UBBE BUHING 3420-* CCE OIE C I-PEC tandard material & color is black neoprene ØB Dash No DH NUBE ee Table I. TEI Blank Neoprene in accordance with 3208 C ilicone in accordance with Fluorosilicone of fluorosilicone blend in accordance with I-DT Ø.150 (3.8).110 (2.8).240 (6.1).200 (5.1).332 (8.4).292 (7.4).464 (11.8).410 (10.4).464 (11.8).410 (10.4).568 (14.4).514 (13.1).777 (19.7).723 (18.4).976 (24.8).898 (22.8).976 (24.8).898 (22.8) (29.6) (27.6) (32.7) (30.8) (42.6) (40.0) (48.9) (46.3) TBE II 3420-* ØB upersedes N (5.8).190 (4.8).322 (8.2).282 (7.2).447 (11.4).407 (10.3).579 (14.7).525 (13 3).642 (16.3).588 (14.9).767 (19.5).713 (18.1).954 (24.2).900 (22.9) (29.0) (27.6) (32.5) (30.5) (35.7) (33.7) (42.0) (40.0) (48.7) (46.1) (61.4) (58.8) ØE Ø ØC Dash No TBE I Ø BØ CØ D.150 (3.8).110 (2.8).240 (6.1).200 (5.1).332 (8.4).292 (7.4).464 (11.8).410 (10.4).589 (15.0).535 (13.6).652 (16.6).598 (15.2).777 (19.7).723 (18.4).976 (24.8).898 (22.8) (32.7) (30.8) (35.9) (33.9) (42.5) (40.0) (48.9) (46.3).230 (5.8).190 (4.8).322 (8 2).282 (7.2).447 (11.4).407 (10.3).579 (14.7).525 (13.3).652 (16.6).535 (13.6).767 (19.5).713 (18.1).954 (24.2).900 (22.9) (32.5) (30.5) (35.7) (33.7) (42.0) (40.0) (48.6) (46.1) (61.3) (58.8).395 (10.0).363 (9.2).521 (13.2).489 (12.4).635 (16.1).603 (15.3).760 (19.3).728 (18.5).905 (23.0).873 (22.2) (27.9) (27.1) (33.8) (33.0) (41.0) (40.2) (47.3) (46.5) (53.4) (52.6) (59.7) (58.9) (72.4) (71.6) I-PEC tandard material & color is black neoprene DH NUBE ee Table II. D (73.8) (72.2) (70.6) (69.1) (67.5) (65.9) (64.3) (62.7) (61.1) (59.5) (57.9) (56.4) (54.8) (53.2) (51.6) (50.0) (48.4) (46.8) (45.2) (43.7) (42.1) (40.5) (38.9) (37.3) TEI Neoprene in accordance with 3208 D ilicone in accordance with Fluorosilicone of fluorosilicone blend in accordance with I-DT ±.031 [50.80±0.79] 3420-* upersedes N * Ø F 41

44 CCE OIE DUT CP & DUY ECEPTCE THEDED COUPING C25042, C25043, C3105 aterial: Cap - luminum alloy Chain - tainless steel COWN PEFIX TYPE Dust Cap for Plug Dust Cap for eceptacle Dummy eceptacle. HE IZE ee Tables below. C D 06 C D 06 FINIH Blank Cadmium olive drab. Black anodize. N Electroless nickel. CHIN ENGTH 1/2 inch increments: e.g. 06 = 3 inches, 07 = 3.5 inches. Only required if length is different from below. C25042 Dust Cap for Plug Ø B THED D X. TEINTION TYPE Blank No termination. B Beaded chain. D ash chain. Wire rope. NO. ØE IN. Dash No. Thread Class 2 B D E* in. Nominal UNEF.562 (14.27).969 (24.61).151 (3.84) 4.00 (101.60) 10 10, UNEF.687 (17.45).969 (24.61).151 (3.84) 4.00 (101.60) 12 12, UNEF.812 (20.62) (29.36).151 (3.84) 4.50 (114.30) 14 14, UNEF.937 (23.80) (29.36).151 (3.84) 4.50 (114.30) 16 16, NEF (26.97) (29.36).151 (3.84) 4.50 (114.30) UNEF (30.15) (29.36).151 (3.84) 4.50 (114.30) UNEF (33.32) (29.36).182 (4.62) 5.00 (127.00) UNEF (36.50) (29.36).182 (4.62) 5.00 (127.00) UNEF (39.67) (29.36).182 (4.62) 5.50 (139.70) UN (46.02) (29.36).182 (4.62) 7.75 (196.85) UN (52.37) (29.36).213 (5.41) 7.75 (196.85) UN (58.72) (29.36).213 (5.41) 7.75 (196.85) UN (65.07) (29.36).213 (5.41) 7.75 (196.85) C25043 Dust Cap for eceptacle ØB THED D X. NO. ØE IN. Dash No. Thread Class 2B B D E* in. Nominal UNEF.688 (17.48).750 (19.05).135 (3.43) 4.00 (101.60) 10 10, UNEF.815 (20.70).750 (19.05).135 (3.43) 4.00 (101.60) 12 12, UNEF (25.40).750 (19.05).135 (3.43) 4.50 (114.30) 14 14, UNEF (28.57).750 (19.05).135 (3.43) 4.50 (114.30) 16 16, NEF (30.18).750 (19.05).135 (3.43) 4.50 (114.30) UNEF (34.14).750 (19.05).135 (3.43) 4.50 (114.30) UNEF (37.31).750 (19.05).135 (3.43) 5.00 (127.00) UNEF (40.49).750 (19.05).135 (3.43) 5.00 (127.00) UNEF (43.66).750 (19.05).166 (4.22) 5.50 (139.70) UN (50.01).812 (20.62).166 (4.22) 7.75 (196.85) UN (56.36).812 (20.62).182 (4.62) 7.75 (196.85) UN (62.71).812 (20.62).182 (4.62) 7.75 (196.85) UN (69.06).812 (20.62).182 (4.62) 7.75 (196.85) 42 C3105 Dummy eceptacle B TYP Ø C 4 HOE ØG TYP aterial: luminum alloy D THED E F Dash No. ( ) ±.031 (±0.79) B ±.005 (±0.25) C ( ) D Thread Class 2 E ( ) (22.22).594 (15.09).120 (3.05) UNEF.562 (14.27).156 (3.96) 10, (25.40).719 (18.26).120 (3.05) UNEF.562 (14.27).156 (3.96) (27.79).812 (20.62).120 (3.05) UNEF.562 (14.27).156 (3.96) (27.79).812 (20.62).120 (3.05) UNEF.750 (19.05).156 (3.96) (30.18).906 (23.01).120 (3.05) UNEF.562 (14.27).156 (3.96) (30.18).906 (23.01).120 (3.05) UNEF.750 (19.05).156 (3.96) (32.54).969 (24.61).120 (3.05) UNEF.562 (14.27).156 (3.96) (32.54).969 (24.61).120 (3.05) UNEF.750 (19.05).156 (3.96) (34.92) (26.97).120 (3.05) UNEF.750 (19.05).203 (5.16) (38.10) (29.36).120 (3.05) UNEF.750 (19.05).203 (5.16) (41.27) (31.75).120 (3.05) UNEF.750 (19.05).203 (5.16) (44.45) (34.92).147 (3.73) UNEF.812 (20.62).203 (5.16) (50.80) (39.67).147 (3.73) UN.812 (20.62).203 (5.16) (57.15) (44.45).173 (4.39) UN.875 (22.22).359 (9.12) (63.50) (49.23).173 (4.39) UN.875 (22.22).359 (9.12) (69.85) (55.58).173 (4.39) UN.875 (22.22).359 (9.12) F

45 DUT CP & DUY ECEPTCE EVEE BYONET COUPING DCP19, DC19 & DP19 CCE OIE TEI: Cap - luminum alloy Chain - tainless steel FINIH: Cadmium olive drab, 48hr. salt spray COWN PEFIX TYPE Dust Cap for Plug Dust Cap for eceptacle Dummy eceptacle. HE IZE ee Tables below. TEINTION TYPE Blank No termination. D ash chain. Wire rope. CB D 06 CB D 06 FINIH Blank Cadmium olive drab. Black anodize. N Electroless nickel. CHIN ENGTH 1/2 inch increments: e.g. 06 = 3 inches, 07 = 3.5 inches. Only required if length is different from below. CB25042 Dust Cap for Plug B NO. ØE IN. B E pprox (29.0).827 (21.0).173 (4.4) (108) (29.0).930 (23.6).173 (4.4) (108) (29.0) (27.5).173 (4.4) (123) (29.0) (30.0).173 (4.4) (123) (37.0) (30.0).173 (4.4) (123) (37.0) (33.5).173 (4.4) (123) (37.0) (37.0).189 (4.8) (138) (37.0) (40.0).189 (4.8) (138) (37.0) (43.5).189 (4.8) (138) (37.0) (49.5).189 (4.8) (206) (37.0) (56.0).220 (5.6) (206) (37.0) (62.5).220 (5.6) (206) (37.0) (67.7).220 (5.6) (206) 1. CB25043 Dust Cap for eceptacle B NO. ØE IN. B E pprox (20.0).925 (23.5).173 (4.4) (108) (20.0) (26.2).173 (4.4) (108) (20.0) (30.5).173 (4.4) (108) (20.0) (33.0).173 (4.4) (108) (25.0) (33.0).173 (4.4) (123) (25.0) (37.5).173 (4.4) (123) (25.0) (41.0).173 (4.4) (123) (25.0) (44.0).173 (4.4) (123) (25.0) (47.5).173 (4.4) (123) (25.0) (54.5).220 (5.6) (206) (25.0) (61.0).220 (5.6) (206) (25.0) (67.5).220 (5.6) (206) (25.0) (73.0).220 (5.6) (206) Consult ales for ing Option 1. CB3105 Dummy eceptacle FONT VIEW T1 IDE VIEW ENVIONENT WHEN UED WITH FNGE EING GET CP36675 O CP4050 ±0.1 ±0.3 Front View T T2 Thread etric UNC ide View ± (18.2) (25.4).126 (3.2) UNC.717 (18.2).110 (2.8).559 (14.2) (20.6) (28.6).126 (3.2) UNC.836 (21.2).110 (2.8).559 (14.2) (23.0) (30.0).126 (3.2) UNC.969 (24.6).126 (3.2).559 (14.2) (24.6) (32.5).126 (3.2) UNC (27.4).126 (3.2).559 (14.2) (24.6) (32.5).126 (3.2) UNC (27.4).126 (3.2).748 (19.0) (27.0) (35.0).126 (3.2) UNC (30.8).157 (4.0).748 (19.0) (29.4) (38.0).126 (3.2) UNC (34.2).157 (4.0).748 (19.0) (31.8) (41.0).126 (3.2) UNC (37.4).157 (4.0).748 (19.0) (34.9) (44.5).146 (3.7) UNC (40.9).157 (4.0).811 (20.6) (39.7) (50.8).146 (3.7) UNC (46.7).157 (4.0).811 (20.6) (44.5) (57.0).169 (4.3) 5 1/4-20UNC (53.4).157 (4.0).874 (22.2) (49.2) (63.5).169 (4.3) 5 1/4-20UNC (59.6).157 (4.0).874 (22.2) (55.5) (69.8).169 (4.3) 5 1/4-20UNC (65.5).157 (4.0).874 (22.2) 1. 43

46 CCE OIE GET FO FNGE OUNT ECEPTCE C36675, C40450 & C40460 For 5015 Threaded & everse Bayonet Coupling PT NUBE HE IZE C H TEI BN Neoprene 80 shore. F ilicone. F ilicone with shielded wire mesh. H Halogen-free. hielded, wire mesh..041[1.04].021[0.53] CP36675 C TYP TYP ØT 4 HOE.036[0.91].026[0.66] CP40450 & CP40460 Ø B Part Number (-67 F to -278 F) 5015 Types: C3100*, C3102*, C3103* everse Bayonet Types: 00*, 02*, 020* Front Panel ount everse Bayonet Types: 03*, 030* ear Panel ount Part Number (0 F to +257 F) Note 2 ±.010 B C ØT ±.010 lternate Part 8 C C [15.09].500 [12.70].875 [22.23].172 [4.37] XXX 10, C C [18.26].626 [15.90] [25.40].172 [4.37] XXX 10 C [18.26].717 [18.21] [25.40].172 [4.37] XXX 12, C C [20.65].750 [19.05] [27.79].172 [4.37] XXX 12, 12 C [20.65].843 [21.40] [27.79].172 [4.37] XXX 14, C C [23.01].875 [22.23] [30.18].172 [4.37] XXX 14, 14 C [23.01].968 [24.60] [30.18].172 [4.37] XXX 16, C C [24.60] [25.40] [32.54].172 [4.37] XXX 16, 16 C [24.60] [27.40] [32.54].172 [4.37] XXX C C [27.00] [28.58] [34.93].203 [5.16] XXX 18 C [27.00] [30.80] [34.93].203 [5.16] XXX C C [29.36] [31.75] [38.10].203 [5.16] XXX 20 C [29.36] [34.20] [38.10].203 [5.16] XXX C C [31.75] [34.93] [41.28].203 [5.16] XXX 22 C [31.75] [37.40] [41.28].203 [5.16] XXX C C [34.93] [38.10] [44.45].203 [5.16] XXX 24 C [34.93] [40.90] [44.45].203 [5.16] XXX C C [39.70] [44.45] [50.80].203 [5.16] XXX 28 C [39.70] [46.70] [50.80].203 [5.16] XXX C C [44.45] [50.80] [57.15].219 [5.56] XXX 32 C [44.45] [53.40] [57.15].219 [5.56] XXX C C [49.23] [55.58] [63.50].219 [5.56] XXX 36 C [49.23] [59.60] [63.50].219 [5.56] XXX C C [55.58] [61.93] [69.85].219 [5.56] XXX 40 C [55.58] [65.50] [69.85].219 [5.56] XXX 44 C C [60.33] [68.28] [76.20].219 [5.56] XXX 48 C C [66.68] [74.63] [82.55].219 [5.56] XXX 1. Dimensions in brackets [ ] are in millimeters. 2. For shielding add after the part number. 3. For silicone material add F after part number 44

47 INDEX INDEX Part Description Page Part Description Page CC42222-* Crown Ordnance eceptacle CC42722-* Crown Ordnance Plug CC * Crown Ordnance eceptacle CC * Crown Ordnance Plug CC * Crown Ordnance dapter C1000-GP* Crown Ordnance dapter C3100* 5015 Wall ount eceptacle C3101* 5015 In ine eceptacle C3102* 5015 Box ount eceptacle C3103P* 5015 Wall ount eceptacle, Potting eal C3104* 5015 Jam Nut C3106* 5015 traight Plug C3106P* 5015 traight Plug, Potting eal C3108* Plug C25042-* 5015 Dust Cap for Plug C25043-* 5015 Dust Cap for eceptacle C36675-* Flange Gasket C40450-* Flange Gasket C40460-* Flange Gasket CB25042-* ev. Bay. Dust Cap for Plug CB25043-* ev. Bey. Dust Cap for eceptacle CB00* ev. Bay. Wall ount eceptacle, Front Panel tg CB01* ev. Bay. In-line eceptacle, Front Panel tg CB02* ev. Bay. Box ount eceptacle, Front Panel tg CB030* ev. Bay. Wall ount eceptacle, ear Panel tg CB03* ev. Bay. Box ount eceptacle, ear Panel tg CB06* ev. Bay. traight Plug CB07* ev. Bay. Jam Nut eceptacle CB08* ev. Bay. 90 Plug * Cable Clamp *C Cable Clamp, Environmental * ubber Bushing for Cable Clamp XX Crimp Pin Contact (F80) unbank Ordnance dapter C-D * ignal Corp. dapter C-D ignal Corp. Plug C ignal Corp. dapter C Ordinance eceptacle D ignal Corp. Plug D ignal Corp. Plug T12-XX Crimp ocket Contact (F80) T Guide Pin for ocket Contact T Contact Insertion Tool T Contact Insertion Tool T Contact Insertion Tool T Contact Insertion Tool T Contact Insertion Tool 1/ T Contact emoval Tool 16 & T Contact emoval Tool T Contact emoval Tool T Contact emoval Tool 1/ T Guide Pin for ocket contact T Guide Pin for ocket Contact Crown Ordnance Coupling Nut * mphonal Ordnance dapter * mphenol Ordnance eceptacle * mphenol Ordnance Plug * mphenol Ordnance dapter * mphenol Ordnance Cap * mphenol Ordnance eceptacle * mphenol Ordnance Plug * mphenol Ordnance Coupling Nut * Crown Ordnance Cap * Crown Ordnance dapter Ordnance Cap Ordinance Grommet Ordinance eceptacle Ordinance eceptacle Ordinance eceptacle Ordinance eceptacle Ordinance eceptacle Ordinance eceptacle Ordinance eceptacle Ordinance eceptacle Ordinance eceptacle Ordinance eceptacle Ordinance eceptacle Ordinance eceptacle Ordinance eceptacle Ordinance eceptacle Ordinance Gasket Ordinance Grommet Ordinance Grommet Ordnance dapter Ordnance dapter Ordnance dapter Ordinance Coupling Nut Type II Ordnance dapter Ordinance eceptacle Ordinance Coupling Nut Ordinance Plug Ordinance Plug Ordinance Plug Ordinance Plug Ordinance Plug Ordinance Plug Ordinance Plug Ordinance Plug Ordinance Plug Ordinance Plug Ordinance Plug Ordinance Plug Ordinance Plug Ordinance Plug * Ordinance Cap

48 Crown Connector has been designing and producing the highest quality connectors since Our connectors are used in a variety of industrial markets, military ground support and heavy equipment. We manufacture or stock almost all of the necessary accessories, including; back shells, adapters, grommets, bushings, caps, clamps, gaskets, nuts and insertion and/or extraction tools. We can take care of any number of modifications for your connectors, such as shells, special platings, paints, keyways, contacts, inserts, insert rotations and more. Depending upon your needs, we can manufacture custom connectors from your designs, or you can work with our engineering team and we will help design and tool custom connectors from scratch. In most cases, our basic stock items can be quickly and inexpensively modified to meet your needs. Crown Connector has an ongoing commitment to expanding our product line. We take pride in setting the industry standard with our excellent customer service. Our state-of-the-art machine shop and automated equipment are specifically designed to meet the needs of our customers. Our plating is far superior than industry requirements. Our products are manufactured for extra-long life and trouble free performance. We have over 25 distributors nationwide. We invite you to check out our website and then call or us with any questions or comments you may have. Phone: Fax: Web: sales@crownconnector.com 3060 North Walnut oad, Unit 160 North as Vegas, NV Cage Code: COPIED ND PODUCED BY COWN CONNECTO, C 2016 COWN CONNECTO, C, NOTH VEG, NV 89115