BH1560 & BH1575 Kubota BX BX2200 Mounting Kit. Before You Start. Assembly Instructions. Manual Part Numbers:

Transcription

1 Land Pride! BH1560 & BH1575 Kubota BX BX2200 Mounting Kit When you see this symbol, the subsequent instructions and warnings are serious - follow without exception. Your life and the lives of others depend on it! Before You Start These assembly instructions contain only information on assembling the BH1560 & BH1575 mounting kit to the BX Series Kubota Tractor. A detailed Operator s Manual was supplied with the main unit when it was purchased. For more specific information on safety concerns refer to the Operator s Manual. Also included in the Operator s Manual is important information on operation, adjustment, troubleshooting, and maintenance for this Backhoe (some of these sections do not apply to all options). A separate Parts Manual for replacement parts can be purchased from your dealer or downloaded from our website at Have model and serial numbers handy when placing an order. Manual Part Numbers: M OPERATOR S MANUAL BH1560/ P PARTS MANUAL BH1560/75 General Information These instructions apply to the Mounting Kit: A FRAME MOUNT & STAB KIT KUB BX BH1560/75 On page 12 is a detailed listing of parts included in this kit. Use this list as a checklist to inventory parts received. The following Assembly will be more easily performed if the rear tires are removed and the rear of the tractor is safely supported. 1. Refer to Figure 1. Remove the three bolts (A) and lockwashers. These will be used to mount the brackets in the next step. Remove the three bolts and lockwashers (B). Discard bolts and keep the lockwashers. B B A B A Figure 1 Copyright 2002 Printed 3/13/ M 1

2 Land Pride 2. Refer to Figure 2. Assemble Left Hand and Right Brackets as shown. Install bolts and lockwashers that were removed in Step 1 in locations labeled "B". Install supplied bolts and the lockwashers that were kept from Step 1 in locations labeled "A". 3. Mount rear tires on tractor and place tractor back on ground. B B A B A Mounting Bracket Figure 2 2 BH1560 & BH1575 Mounting Kit M 3/13/02

3 Land Pride 4. Refer to Figure 3. Remove the lower hitch brackets that are currently mounted to the backhoe. Assemble the brackets supplied in the mounting kit as shown. Mounting hardware is supplied with kit or hardware that was removed from brackets may be used. Lower Brackets Figure 3 3/13/02 BH1560 & BH1575 Mounting Kit M 3

4 Land Pride 5. Refer to Figure 4. Place Hydraulic Reservoir U-Bolts on Backhoe frame as shown (BH1560 only). For the BH1575, remove the front valve cover and mount the hydraulic tank in the same holes. U-Bolt U-Bolt Figure 4 4 BH1560 & BH1575 Mounting Kit M 3/13/02

5 Land Pride 6. Refer to Figure 5. Assemble Hydraulic Reservoir to the Backhoe using the U-Bolts placed in Step 4. (BH1560) Hydraulic Reservoir Figure 5 3/13/02 BH1560 & BH1575 Mounting Kit M 5

6 Land Pride 7. Assemble PTO Drive adapter to PTO pump as shown in Figure 6. PTO Drive Adapter PTO Pump 8. Assemble the Suction Pump Adapter and Pressure Pump Adapter to the Pump as shown in Figure 7. Figure 6 Suction Pump Adapter Pressure Pump Adapter PTO Pump Figure 7 6 BH1560 & BH1575 Mounting Kit M 3/13/02

7 Land Pride 9. Install Filter Screen and Suction Hose Barb as shown in Figure 8 Filter Screen Hose Barb Figure 8 3/13/02 BH1560 & BH1575 Mounting Kit M 7

8 10. Assemble Suction Hose (Large Hose) end without fitting to Hydraulic Reservoir with Hose Clamp. Assemble the end with fitting to the Pump Suction Adapter. 11. Assemble Elbow Adapter to Hydraulic Reservoir making sure that elbow is pointing up. Land Pride 12. Disconnect hose from inlet side of valve and connect to Elbow on Hydraulic Reservoir. 13. Disconnect Return Hose (Pressure) and connect to Pressure Adapter on Pump. Hose Clamp Inlet Hose Elbow Suction Hose Return (Pressure) Hose Figure 9 Inlet Valve of Backhoe Valve Suction Filter Tank Press. Oil Reservoir (Backhoe or Tractor Sump) Pump Return Hose From Backhoe Valve Figure 10 8 BH1560 & BH1575 Mounting Kit M 3/13/02

9 Land Pride 14. Assemble torque bar to Pump with 3/8" bolts and locknuts as shown. 15. Back tractor up to backhoe just close enough to assemble the Pump to tractor s PTO drive shaft. Do not back completely up to backhoe. Leave some room for PTO pump and assembly. The Pump should be assembled so that the Torque Bar is pointing up. 16. Set lower 3-point arms 9" from ground to center of swivel ball, then back the tractor until lower 3-point align with lower mounting brackets on the backhoe then attach accordingly. Torque Bar PTO Pump 3/8" Bolts & Locknuts Figure 11 3/13/02 BH1560 & BH1575 Mounting Kit M 9

10 Land Pride 17. Align tractor s lower 3-point arms and locking bar with the bottom holes of backhoe s lower 3-point brackets. The locking bar will be beneath the lower 3-point arms. Install pins and secure with lynch pins. Align the locking bar s eyebolts with the top holes of the Backhoes 3-point brackets. Install pins and secure with lock pins. There may be some adjustment of the eyebolts to align with the top holes. 3-Point Arms Above Locking Bar Eyebolt Adjustment Nuts Lock Pins Pins Locking Bar Figure BH1560 & BH1575 Mounting Kit M 3/13/02

11 Land Pride Frame Stabilizer Bar Assembly 1. Place the Stabilizer Bar between the frame to make sure it will fit. The Stabilizer Bar end plates might need to be tweaked so that it fits between the frame as shown. 2. Assemble the two hole plate to the threaded hole of the Stabilizer Bar as shown capturing the frame between the Bar and the two hole plate. 3. Place the flat washer on the bolt and insert it through the top hole of two hole plate, through the hole in the tractor frame and through the top hole of the Stabilizer Bar. 4. Assemble the one hole plate to the other end of the Stabilizer Bar, capturing the tractor frame between the bar and the plate. Bolt, flat washer, lock washer and nut Bolt Two hole plate Stabilizer Bar One hole plate Figure 13 Disassembly 1. Lower bucket & stabilizers to the ground to get a sturdy base before any pin or pump removal. 2. Disconnect the Pump from the tractor s PTO shaft. 3. Disassemble the locking bar completely. Top link and/ or stabilizer need to be unpinned before removing backhoe. 4. Drive away from Backhoe. 3/13/02 BH1560 & BH1575 Mounting Kit M 11

12 Listing of Parts Land Pride A FRAME MOUNT & STAB. KIT KUB BX BH1560/75 Your Kit Includes: Qty. Part No. Part Description K 3 PT STABILIZER KIT BH1575 Qty. Part No. Part Description C 1/4" LINCH PIN BH STABILIZE C ADJ.STABILIZER LINK CAT1 BH C PIN,3/4X4 1/2 W/LOOP BH Qty. Part No. Part Description K FRME MNT KUB BX 1560 Qty. Part No. Part Description D WASHER W/1 HOLE 3/8X3SQ D WASHER W/2 HOLE 3/8X2X3 3/ H FRAME MOUNT BRKT RH BX18/ H FRAME MOUNT BRKT LH BX18/ H CROSSTUBE WELDMT BX18/ H SPCL LWR LINK BRKT RH BX18/ H SPCL LWR LINK BRKT LH BX18/ C HHCS 5/8-11X2 GR C HHCS 3/4-10X1 1/2 GR C NUT LOCK 5/8-11 PLT C WASHER FLAT 5/8 USS PLT C WASHER LOCK SPRING 3/4 PLT C WASHER LOCK 9/16 PLT C 1/4" LINCH PIN BH STABILIZE C PIN,3/4X4 1/2 W/LOOP BH C PIN LOWER HITCH 7/8X3 1/ C PIN HITCH 1X5 3/4 CAT II C CAPSCREW 14MMX1.5MMX50MM C CAPSCREW 9/16-12X1 3/ C PIN CLEVIS 3/4X3 1/ C FITTING ADAPTOR C5205X6X C HOSE 3/8X1/2MALEX9/16JICFX C HOSE 3/8X1/2MALEX9/16JICFX C NUT HEX 9/ BH1560 & BH1575 Mounting Kit M 3/13/02