Spare parts catalogue ST3 S ABS U.S.A DUCATI SPORTTOURING

Transcription

1 Spare parts catalogue ST S ABS U.S.A DUCATI SPORTTOURING

2

3 GENERAL INFORMATION The present spare parts order exactly the right spare parts When ordering specify: ) the part's code number followed by its description; quantity needed; 2) the motorcycle's serial number, stamped on the steering head. Reference to right and left apply to the vehicle in terms of its direction of move-ment. Spare parts drawings are general and do not represent the part. The contents of this catalogue are general and can undergo changes without prior notice. VALIDITY f.m. d.m. f.m.m. d.m.m. LIST CAL CDN Until V.I.N. From V.I.N. Up to engine number From engine number California Canada Ducati Motor Holding S.p.A. Commercial and Administation Office: Via A. Cavalieri Ducati n. 402 Bologna, Italy Telefono 05 4 Fax Internet

4 Paints Paint Code "Rosso Anniversary DUCATI" "Nero Lucido DUCATI" (for CAN/CAL version) "Grigio Scuro Metallizzato" (not for CAN/CAL version) (PPG) 47.0 (PPG) (PPG) *007 2

5 page Contents a 00b 00c 00d a a a Workshop service tools Workshop service tools Workshop service tools Dds tester Workshop service tools Gearchange control Gearbox Clutch Clutch-side crankcase cover Connecting rods Cylinders - pistons Timing system Filters and oil pump Crankcase halves Water pump-altr-side crnkcse cover Water pump-altr-side crnkcse cover Electric starting and ignition Cylinder head : timing system Manifolds and cylinder head covers Vertical cylinder head Horizontal cylinder head Throttle body Exhaust system Stands Frame L.h. footrests R.h. footrests Headlight support Headlight and electrical wiring Headlight Instrument panel Handlebars and controls Front forks Clutch control Front hydraulic brake Radiator Cooling system Electrical system Battery support Air intake - oil breather Swingarm and drive chain Rear suspension Oil cooler Rear hydraulic brake Front and rear wheels Number plate holder Seat Fuel tank Fuel system Headlight fairing Fairing Pannier fasteners Side panniers Antilock braking system (abs) Evaporative emissions canister Data plate positions

6 DRAWING 00 Workshop service tools

7 DRAWING 00 Workshop service tools NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY Timing belt roller reaction tool Head nuts holder wrench 7.20 Head mounting base Degree wheel Degree wheel holder tool for ignition advance check Exhaust valve guide punch tool Punch tool to extract valve guide Intake valve guide punch tool T.D.C. control gauge A Torque wrench for timing belt 7.07 Crankshaft gear holder wrench for tightening nut Punch tool for driving exhaust valve seat Valve lift gauge Punch tool for driving intake valve seat Fork feeler gauge 0. mm Fork feeler gauge 0,2 mm Fork feeler gauge 0. mm Timing belt control gauge Tool to hold crankshaft in TDC position Spacer for checking lower valve shim Flywheel Wrench Crankcases assembling cap Plate for positioning gear engagement fork Conversion kit for 2V belts tensioning tool 5

8 DRAWING 00a Workshop service tools

9 DRAWING 00a Workshop service tools NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY Drive roller puller Rocker shaft extractor Wrench for tightening primary transmission ring nut Sleeve for installing clutch bell gear Extractor for primary drive gear Tool to drive valve seal ring ø Torque wrench Wrench for camshaft pulley ring nut adjustment Tool to fit seals on camshafts Half-rings mounting punch tool 7.25 Torque wrench for timing belt Tool to drive valve seal ring ø Tool to install rocker arm shaft clip Cam axis locking tool Reaction tool for wet "FCC" clutch 7

10 DRAWING 00b Workshop service tools

11 DRAWING 00b Workshop service tools NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY 7.02 Tool for assembling the steering head bearings Wrench for front wheel spindle 7.44 Tool for assembling chain A Coupling Frame/engine mount Stopper for driving the half bearing of the steering head base Union for exhaust gas suction 7.09 Tool for overhauling SHOWA forks - assembling seal ring Wrench for assembling the steering head cap 9

12 DRAWING 00c Dds tester

13 DRAWING 00c Dds tester NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY DDS (Ducati Diagnosis System) + manifold vacuum meter. kit Belt tensioning kit 75.7 Sensor Bracket Battery Feeder DDS manual (USB) Memory card reader Main cable Fuse Software DDS CD (USB) Cable extension Black case with sponge rubber V Amperometer plier Battery charger

14 DRAWING 00d Workshop service tools

15 DRAWING 00d Workshop service tools NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY A Fuel pressure line HS A Fuel pressure line ST/SS/M A Oil pressure line A Fitting - cylinder compression M A Fitting - cylinder compression M A Cable Volt PF DUC Main cable (MARELLI) 4..4.A Oil pressure fitting A Cable for supplementary tests A Red clamp cable A Black clamp cable A Temperature probe Battery connection adapter A Electric lighter connection adapter (ST) A Battery connection adapter A Red case with sponge rubber 75.2T DUCATI sticker RH/LH side (USB) Adaptor Depressure sensor A Pressure sensor Feeder Depressure/pressure line Union Pressure kit C Cable for potentiometer adjustement

16 DRAWING 002 Gearchange control

17 DRAWING 002 Gearchange control NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY A Return spring A Washer A Special screw A Gear stopper assembly A Gasket th B Switch A Push rod holder Gasket Gear selector spring Ball A st,4th-2nd,rd gear selector fork A 5th,th gear selector fork Fork pin A Shim th Circlip A Needle retaining ring (square cross-section) A Pin A Complete gearbox drum Shim th A Shim th A Fork return spring Shim th Shim th A Ring A Nut A Gearbox drum control fork Gearchange lever pin A Pin with gearchange lever Gearchange lever return spring B Screw A Washer B Screw A Washer A Centering ring A Stopper plate Shim th Shim th A Ball A Spring A Aluminium gasket th A Aluminium gasket th., A Gasket A Special screw 5

18 DRAWING 00 Gearbox

19 DRAWING 00 Gearbox NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY Shim th A Gearbox main shaft Shim th A Needle bearing A Driving gear 5th sp A Grooved washer th Snap ring A Driving gear rd/4th sp A Driving gear th sp B Driving gear 2nd sp E Shim th A Front sprocket w/rubber protection Z= A Spacer A O-ring A Spacer th., A Grooved washer th Needle bearing B Driven gear st sp Shim th A Driven gear 5th sp A Driven gear 4th sp A Driven gear rd sp A Driven gear th sp B Driven gear 2nd sp A Gearbox lay shaft Shim th A Complete main shaft A Gearbox lay shaft A Lock washer A Nut 7

20 DRAWING 004 Clutch

21 DRAWING 004 Clutch NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY A Clutch spring A Retainer C Screw A Pressure plate "FCC" A Bearing B Screw A Hexagon nut A Spring washer A Clutch plates set A Spring washer "FCC" A Spring A Plate holder hub "FCC" A Spacer A Clutch housing A Spacer A Clutch control rod O-ring A O-ring A Piston assembly A Clutch control pin "FCC" 9

22 DRAWING 005 Clutch-side crankcase cover

23 DRAWING 005 Clutch-side crankcase cover NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY A Cover clutch side B Screw B Screw A Oil level sight glass B Screw A Panel (BLACK) B Screw Bush A Seal ring A Shim th A Circlip O-ring 7..0.A Locating bush A Holder A Complete cap A Washer A Cover A Spacer A Screw A Gasket th A Switch 2

24 DRAWING 00 Connecting rods

25 DRAWING 00 Connecting rods NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY A Crankshaft A Special screw A Nut Threaded dowel A Connecting rods pair A Bush Pin AB Half-bearing (BLUE) AC Half-bearing (YELLOW) A Special screw Woodruff key A Shim th B Shim th C Shim th D Shim th. 2, E Shim th. 2, F Shim th. 2, G Shim th H Shim th I Shim th J Shim th K Shim th. 2, L Shim th. 2, M Shim th N Shim th A Lock washer A Ring nut Woodruff key A Spring washer A Primary drive front sprocket 2

26 DRAWING 007 Cylinders - pistons

27 DRAWING 007 Cylinders - pistons NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY A Horizontal cylinder-piston fit A Complete piston A Piston pin circlip A Piston pin A Piston rings set A Stud bolt A Cylinder-crankcase gasket th A Bush A Head-cylinder gaskets set A Vertical cylinder-piston fit A Hose guide A O-ring A Water inlet union to cylinders B Screw A Head-cylinder gasket A Horizontal cylinder water inlet hose A Vertical cylinder water inlet hose 25

28 DRAWING 00 Timing system

29 DRAWING 00 Timing system NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY A Vertical timing belt cover B Screw B Screw A Horizontal timing belt cover A Bearing A Ring A Complete vertical cylinder tensioner roller A Screw A Timing lay shaft B Timing gears pair 5..0.A Lock washer Hexagon nut A Spacer A Snap ring A Timing belt roller A Belt roller separating washer A Spacer A Elastic-stop ring nut A Timing drive toothed belt A Fixed tensioner assembly Woodruff key 27

30 DRAWING 009 Filters and oil pump

31 DRAWING 009 Filters and oil pump NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY A Complete oil pump A Cap A Aluminium gasket A O-ring A Bypass valve A Bypass cap A Bypass spring B Screw A Spring washer B Screw A Spring washer A Pump drive gear A Bush A Bypass spring Locating bush A Gasket A Oil drain plug with magnet A Gasket th., A Oil filter A Oil filter cartridge A Nipple O-ring A Cap A Snap ring A Circlip Reduction bush A Cap A Gasket th.2 29

32 DRAWING 00 Crankcase halves

33 DRAWING 00 Crankcase halves NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY A Complete half-crankcases pair Seal ring Needle bearing Snap ring Fluid sealant A Stud bolt for fastening head cylinder A Special washer A Nut A Bearing Screw A Keep plate A Bearing A Seal ring A Spacer B Screw Seal ring Bearing Circlip A Aluminium gasket th A Bearing A Bearing holder bush A Seal ring A Locating dowel B Screw Bearing A Bearing B Screw O-ring A Bearing A Bearing holder bush B Screw A Bush B Breather valve O-ring A Nipple A Screw A Aluminium gasket th., A Bush A Special screw

34 DRAWING 0 Water pump-altr-side crnkcse cover Rif. 4 / 22 - Tav. 0a

35 DRAWING 0 Water pump-altr-side crnkcse cover NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY A Generator d.m.m A Generator f.m.m B Screw A Screw A Bearing Circlip B Screw A Washer A A 0 Ring A Bearing A Washer A Bearing B Spacer 7..0.A Locating bush A Bracket B Screw A Water pump fan Fluid sealant A Seal B Mechanical seal A Washer A Holder B Screw A Spacer

36 DRAWING 0a Water pump-altr-side crnkcse cover

37 DRAWING 0a Water pump-altr-side crnkcse cover NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY AE Chain cover B Screw A Cap Seal ring A O-ring BC Cover B Screw A Sensor A Gasket th.0, AA Gasket th.0, AB Gasket th., A O-ring B Screw A Water pump delivery filler A Complete water pump cover A Generator cover A Gasket A Cap A Gasket th A Locating dowel B Screw A Aluminium gasket A Spring washer BB Generator cover A Oil level sight glass B Screw B Screw 5

38 DRAWING 02 Electric starting and ignition

39 DRAWING 02 Electric starting and ignition NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY A Complete starter motor A Spring washer A Nut A Starter motor gasket B Screw A Starter motor sprocket A Circlip Intermediate gear pin A Washer A Intermediate gear assembly Circlip B Screw A Flange A Locating pin A Check ring B Ignition flywheel Washer..00.C Inner ring A Needle bearing A Electric starter driven gear A Starter clutch B Screw B Screw A Flexible bush 7

40 DRAWING 0 Cylinder head : timing system

41 DRAWING 0 Cylinder head : timing system NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY A Elastic-stop ring nut A Washer A Timing belt roller A Screw A Vertical belt inner cover A Horizontal belt inner cover A Seal ring Woodruff key A Vertical head camshaft B Screw A O-ring A Side cap A O-ring B Screw A O-ring A Horizontal head camshaft A Special washer A Stud bolt A Flange A Gasket A Screw 4 9

42 DRAWING 0a Manifolds and cylinder head covers

43 DRAWING 0a Manifolds and cylinder head covers NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY B Screw A Valve cover A Head gasket A Intake manifold A Aluminium gasket th B Screw A Exhaust valve cover (horizontal) A Hose guide 2 4

44 DRAWING 04 Vertical cylinder head

45 DRAWING 04 Vertical cylinder head NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY 0.2..C Complete vertical head 2 04.A.00.A Intake valve seat A.00.AB Oversize intake valve seat A.00.AC Oversize intake valve seat A.004.A Exhaust valve seat 04.A.004.AB Oversize exhaust valve seat A.004.AC Oversize exhaust valve seat A Intake valve guide AB Intake valve guide magg. 0, AC Intake valve guide magg. 0, AD Intake valve guide magg. 0, A Exhaust valve guide AB Oversize valve guide AC Oversize valve guide AD Oversize valve guide A Rubber pad A R.H. Closing rocker spring..04.a Hose guide B Screw B Intake valve B Exhaust valve Washer A Spring A Opening rocker A Opening rocker shaft B Closing rocker B See table E Split rings A See table A L.H. Closing rocker spring B Closing rocker shaft A Washer A Holder A Return spring 4

46 DRAWING 05 Horizontal cylinder head

47 DRAWING 05 Horizontal cylinder head NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY C Complete horizontal head A Exhaust valve guide AB Oversize valve guide AC Oversize valve guide AD Oversize valve guide A Intake valve guide AB Intake valve guide magg. 0, AC Intake valve guide magg. 0, AD Intake valve guide magg. 0, A.00.A Intake valve seat A.00.AB Oversize intake valve seat A.00.AC Oversize intake valve seat A.004.A Exhaust valve seat 5 04.A.004.AB Oversize exhaust valve seat A.004.AC Oversize exhaust valve seat B Exhaust valve B Intake valve A R.H. Closing rocker spring A L.H. Closing rocker spring A Opening rocker shaft A See table E Split rings B See table A Opening rocker B Closing rocker A Spring Washer A Rubber pad B Closing rocker shaft A Return spring 45

48 DRAWING 0 Throttle body

49 DRAWING 0 Throttle body NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY B Throttle body A Gasket A O-ring A Air funnel A Air funnel A Spring Screw A Injector A Stepper motor A Pressure pick-up point A Clamp "M" A Tube A Tube A Clamp "R" 47

50 DRAWING 07 Exhaust system

51 DRAWING 07 Exhaust system NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY A Exhaust gasket A Gasket th A L.H. silencer A Nut A Vertical head exhaust pipe A Clamp B Horizontal head exhaust pipe A Cap A Spring 0..0.A Rubber pad A R.H. silencer B Screw A Stud bolt A Rubber pad A R.H. bracket Washer Screw A L.H. bracket A Lambda sensor 49

52 DRAWING 0 Stands

53 DRAWING 0 Stands NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY AB Nut A R. H. Plate A Central stand B L. H. Plate A Inner spring A Outer spring A Screw B Screw B Inner spring B Outer spring B Plate A Screw A Switch C Side stand D Pivot D Plate 5

54 DRAWING 09 Frame

55 DRAWING 09 Frame NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY AA Frame (METALLIC DARK GREY) J AB Frame (BLACK) AF Frame (RED) A Mudflap A Hose guide AB L.H. holder AB R.H. holder 7..2.A Spacer A Vibration damper pad A Holder A Washer A Screw A Special screw A Cap A Stud bolt A Screw B Screw A Nut A Cap A Locks kit A Hose guide A Rubber pad B Rod A Hose guide Bush 2 5

56 DRAWING 020 L.h. footrests

57 DRAWING 020 L.h. footrests NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY A L.H. foot peg holder plate A Screw A Pin Spring A Nut A Ball joint AB Nut 7..0.A Gearbox transmission rod A Nut A Ball joint B Screw A Gearchange control lever A Washer Bush A Rubber pad A Gearchange lever Circlip A Pin B Plate A Screw A Plate Foot peg rubber cover Front L.H. foot peg, complete A Screw A Protection B Screw A Handle A Spring pin A Spring C Rear L.H. foot peg holder plate A Plate A Spring A Ball B Keep plate Rear L.H. foot peg, complete 0..0.A Handgrip A Power Point B Screw 55

58 DRAWING 02 R.h. footrests

59 DRAWING 02 R.h. footrests NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY B R.H. foot peg holder plate A Pin Spring Circlip A Screw A Screw A Plate Foot peg rubber cover Front R.H. foot peg, complete B Keep plate A Ball A Spring Rear R.H. foot peg, complete A Plate C Rear R.H. foot peg holder plate A Protection A Screw 2 57

60 DRAWING 022 Headlight support

61 DRAWING 022 Headlight support NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY 29...AB L.H. holder A Holder B Screw AB R.H. holder A Holder A Screw B Screw B Screw A Nut A Pin A Vibration damper pad A Screw A Holder Hose guide B Screw..0.2A Hose guide A Washer 59

62 DRAWING 02 Headlight and electrical wiring

63 DRAWING 02 Headlight and electrical wiring NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY A Fuse A A Fuse 7.5A A Fuse 5A A Fuse 20A A Fuse 5A A Clip A Pin A Fairlead B Screw B Spacer A Rubber pad A Vibration damper pad A Screw C Regulator A Relay A Rubber holder B Screw A Front wiring G Cover 27...A Plate A Air temperature sensor B Sticker?schema fusibili? A Warning lamp bulb 2V-W A Screw

64 DRAWING 02a Headlight

65 DRAWING 02a Headlight NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY C Complete headlight A Bulb 2V-55W H A Bulb A Cover A Spring A Rubber pad 4

66 DRAWING 024 Instrument panel

67 DRAWING 024 Instrument panel NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY C Complete instrument panel N0 Spring washer B Spacer A Nut B Front headlight fairing panel A Rear headlight fairing panel A Spacer A Quik fastening A Screw A Insert 4 5

68 DRAWING 025 Handlebars and controls

69 DRAWING 025 Handlebars and controls NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY A Nut B Special screw B Steering head base A Washer A Seal ring A Bearing B Screw A Wrench with Transponder A Wrench without Transponder D Key-operated switch A Pin A Plate A Split pin Belt B L.H. switch Grips pair C L.H. handlebar A Screw B Cover B Screw B Special screw A Washer B Screw A Steering head B R.H. handlebar A R.H. switch B Throttle control transmission A Cover A Nut B Antenna A Throttle control A Counterweight A Screw A Bush A Ring nut A Mudflap Screw A Pin B Screw A Cap A Bush 2 7

70 DRAWING 02 Front forks

71 DRAWING 02 Front forks NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY A R.H. fork leg assembly A Centering ring A Damper tube A L.H. fork leg assembly B Complete L.H. slider..09.a Spring A Spring coupling A Coupling A Rubber cush drive hub A Complete cap A Snap ring Hose guide A Screw A Stanchion tube B Adjusting screw A Special washer A Complete R.H. slider 9

72 DRAWING 027 Clutch control

73 DRAWING 027 Clutch control NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY A Clutch drive pump A Clutch control lever A Spare lever pin C Bracket A Complete oil tank A Cap AB Special screw A Gasket th A Clutch control pipe A Special screw Bleed A Dust seal A Microswitch 7

74 DRAWING 02 Front hydraulic brake

75 DRAWING 02 Front hydraulic brake NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY A Front brake pump A Brake control lever A Spare lever pin B Screw D Bracket A Microswitch A Complete oil tank A Gasket th AB Special screw B Screw A R.H. brake caliper A L.H. brake caliper A Spring A Holder A Tank cap A Spare pins and spring A Plate A Dust seal A Spare bleed union B Pads pair 2 7

76 DRAWING 029 Radiator

77 DRAWING 029 Radiator NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY A Water radiator A Radiator cap A Screw A Electric fan A Special screw A Vibration damper pad A Holder A Spacer A Screw 75

78 DRAWING 00 Cooling system

79 DRAWING 00 Cooling system NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY A Water tank Tank cap B Screw B Spacer 4 5 A00.70 Hose guide A Hose A Hose guide A Clamp A Sensor A O-ring A Water outlet union A Hose guide A Cooler/thermostat hose A Water outlet union B Screw A Thermostat/pump hose A Thermostat/pump hose A Pump/cooler hose A Thermostat A Insert A Bush A Hose guide 77

80 DRAWING 0 Electrical system

81 DRAWING 0 Electrical system NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY A Electric wiring A Fuse 40A A Screw B Holder B Screw AB Horn (BLACK) A Vertical spark plug cable - left C Coil A Horizontal spark plug cable - right A Horizontal spark plug cable - left Hose guide B Spark plug A Hose guide A Vertical spark plug cable - right A Rubber pad A End section A Connector A Relay A Holder A Fuse A B Screw Nut A Hose guide A Fuse 20A 2 79

82 DRAWING 02 Battery support

83 DRAWING 02 Battery support NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY D Injection control unit A Battery - solenoid starter cable AB Nut A Solenoid starter - starter motor cable A Nut A Spring washer A Remote switch B Nut A Washer B Spacer B Spacer A Plate B Screw 4..0.A Rubber pad B Screw Rubber pad C Battery A Rubber cap Hose guide A Screw A Plate B Battery box mount A Vibration damper pad A Plate A Screw A Spacer A Special screw D Battery grounding cable

84 DRAWING 0 Air intake - oil breather

85 DRAWING 0 Air intake - oil breather NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY B Stud bolt A Screw A Nut A Clip B Bracket B Air filter box A Tube B Screw B Spacer A Rubber pad B Hook Spring pin A Pin A Washer A Hose guide 7..0.A Breather pipe A Screw D Oil breather tank A Filter/fuel tank outlet pipe Filter element A Filter case cover A Air funnel B Screw AB Nut 2

86 DRAWING 04 Swingarm and drive chain

87 DRAWING 04 Swingarm and drive chain NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY B Nut A Rear wheel spindle B Special screw A Lower chain sliding shoe A Chain adjustment sticker A Cap A Snap ring A Swingarm pivot C Screw C Complete swingarm A Final drive kit B Shim th B Shim th B Shim th A Upper chain sliding shoer B Nut A Chain (02 Links) A Rear mudguard B Plate A Cap A Screw A Sliding shoe A Cover B Screw A Locating pin A Clamp 2 5

88 DRAWING 05 Rear suspension

89 DRAWING 05 Rear suspension NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY A Rocker assembly A Seal ring A Needle bearing A Bush B Screw A Shock absorber B Screw A Spacer B Bush A Screw A Screw A Bush B Nut C Clamp B Nut A Tie rod A Plate B Screw B Screw A Nut Nut A Ball joint A Ball joint B L.H. nut 7

90 DRAWING 0 Oil cooler

91 DRAWING 0 Oil cooler NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY B Oil cooler Vibration damper A Vibration damper pad A Spacer A Screw A Oil return pipe A Oil delivery pipe A Special screw A Oil delivery pipe A Special screw A Gasket th. 9

92 DRAWING 07 Rear hydraulic brake

93 DRAWING 07 Rear hydraulic brake NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY A Holder A Washer A Ring Bush A Rubber pad A Brake control lever A Pedal pin A Threaded dowel 9 0N502 Nut A Pin A Fork A Screw A Adjuster rod B Screw B Switch A Tube A Hose guide A Screw A Cap A Complete oil tank A Screw A Copper gasket sp A Nut A Holder AB Special screw A Gasket th A Rear brake pump A Spare union A Dust cover B Screw A Clip Spacer A Screw A Spacer B Screw A Rear brake caliper Spare bleed union.4.02.a Pads pair A Spare pins and spring A Dust seal B Spring 9

94 DRAWING 0 Front and rear wheels

95 DRAWING 0 Front and rear wheels NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY AA Wheel rim (front) (GREY) AB Wheel rim (front) (BLACK) AE Wheel rim (front) (RED) A Valve A Spacer (internal) A Bearing A Brake disc A Screw A Screw C Front wheel spindle B Spacer Seal ring A Circlip C Nut AA Wheel rim (rear) (GREY) AB Wheel rim (rear) (BLACK) AE Wheel rim (rear) (RED) A Spacer (internal) A Brake disc A Valve A Bearing A Vibration damper B Pin AB Nut A Rear sprocket flange B Bush D Ring gear Z= B Spacer A Front brake disc 9

96 DRAWING 09 Number plate holder

97 DRAWING 09 Number plate holder NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY A Screw AA Handle (RED) AG Handle (METALLIC DARK GREY) AT Handle (BLACK) A Lock latch A Screw A Seat lock B L.H. turn indicator Bulb A Cup B Washer B Nut B Spacer A Nut A Insert A Rubber pad A Tail light A Two-light bulb 2V 5/2W A Pin A Lens A Washer Bulb A Wiring B Screw B R.H. turn indicator A Tail lamp A Reflector A Screw A Plate B Screw A Number plate holder A Cap A Hose guide A Mudflap A Mudflap A Screw A Holder 95

98 DRAWING 040 Seat

99 DRAWING 040 Seat NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY A Panel (BLACK) A Cap A Screw B Plate A Holder A Screw B Spacer A Hook A Clamp A Screw B Screw A Washer A Spacer A Threaded insert A Rubber pad A Seat A Screw BA L.H. body panel (RED) BG L.H. body panel (METALLIC DARK GREY) BT L.H. body panel (BLACK) A L.H. gasket A R.H. gasket BA R.H. body panel (RED) BG R.H. body panel (METALLIC DARK GREY) BT R.H. body panel (BLACK) A Tool box AB Nut L Owner's manual A Tool bag A Padlock A Helmet anti-theft wire A L.H. body panel (unpainted) A R.H. body panel (unpainted) A Nylon washer A Rubber A Sticker "SPORTTOURING" (for RED, METALLIC DARK GREY, BLACK) 2 97

100 DRAWING 04 Fuel tank

101 DRAWING 04 Fuel tank NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY AA Tank (RED) AG Tank (METALLIC DARK GREY) AT Tank (BLACK) A Tank cap A Split pin A Washer A Bush A Screw B Plate D Pin A Tube A Hose guide A Rubber holder A Fuel level sensor Nylon washer B Screw B Screw A Cover gasket B Nut A Nut A Rubber pad A Cap A Gasket th A Bracket A Panel A Screw BB Cover (BLACK) A Gasket A Nut A Vibration damper pad 99

102 DRAWING 042 Fuel system

103 DRAWING 042 Fuel system NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY A Flange A Special screw A Washer A Union Circlip A Gasket th A Cap A Fuel pump filter A Snap ring B Manifold B Pump holder A Fuel pump A Hose guide A Tube A O-Ring.4.02.A O-ring Self-tapping screw A Holder A O-ring A Air separator A Tube B Fuel filter A Filter/pump pipe A Tube A Pressure regulator Circlip A O-Ring A Pump wiring A Union 0

104 DRAWING 04 Headlight fairing

105 DRAWING 04 Headlight fairing NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY 4..0.BA Headlight fairing (RED) 4..0.BG Headlight fairing (METALLIC DARK GREY) 4..0.BT Headlight fairing (BLACK) 4..0.B Headlight fairing (unpainted) A Screw A Insert Washer B Screw A Screw A Bulb A R.H. turn indicator A L.H. turn indicator B Screw A R.H. gasket BA R.H. rear-view mirror (RED) BG R.H. rear-view mirror (METALLIC DARK GREY) BT R.H. rear-view mirror (BLACK) A L.H. gasket BA L.H. rear-view mirror (RED) BG L.H. rear-view mirror (METALLIC DARK GREY) BT L.H. rear-view mirror (BLACK) A Windshield 0

106 DRAWING 044 Fairing

107 DRAWING 044 Fairing NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY B L.H. upper half-fairing (unpainted) AA L.H. upper half-fairing (RED) AG L.H. upper half-fairing (METALLIC DARK GREY) AT L.H. upper half-fairing (BLACK) B Washer Bush C Retainer B Screw B Screw Washer A Insert A L.H. lower half-fairing (unpainted) AA L.H. lower half-fairing (RED) AG L.H. lower half-fairing (METALLIC DARK GREY) AT L.H. lower half-fairing (BLACK) A Screw AA R.H. sticker "DUCATI STS ABS" (for RED, BLACK) AB R.H. sticker "DUCATI STS ABS" (for METALLIC DARK GRAY) AA Air manifold (RED) AG Air manifold (METALLIC DARK GREY) AT Air manifold (BLACK) A Air manifold (unpainted) AB R.H. air manifold (BLACK) A Screw B Bent plate A Nylon washer B Screw AA Front mudguard (RED) AG Front mudguard (METALLIC DARK GREY) AT Front mudguard (BLACK) A Front mudguard (unpainted) B Screw AA L.H. sticker "DUCATI STS ABS" (for RED, BLACK) AB L.H. sticker "DUCATI STS ABS" (for METALLIC DARK GRAY) A Clip B Washer B Shear rivet A R.H. lower half-fairing (unpainted) AA R.H. lower half-fairing (RED) AG R.H. lower half-fairing (METALLIC DARK GREY) AT R.H. lower half-fairing (BLACK) B R.H. upper half-fairing (unpainted) AA R.H. upper half-fairing (RED) AG R.H. upper half-fairing (METALLIC DARK GREY) AT R.H. upper half-fairing (BLACK) AB L.H. air manifold (BLACK) B Screw AB Cat's eye (AMBER) 2 05

108 DRAWING 045 Pannier fasteners

109 DRAWING 045 Pannier fasteners NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY A R.H. holder A L.H. holder A Screw A Screw A Spacer A Screw 2 7 BB0.070 Screw A Screw A Cap A Holder B Special screw 4 07

110 DRAWING 04 Side panniers

111 DRAWING 04 Side panniers NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY AA Sticker "DUCATI" (for RED, METALLIC DARK GRAY) AA Coplete panniers kit (RED) AG Complete Panniers kit (METALLIC DARK GREY) Self-tapping screw A R.H. handle Self-tapping screw A Reflector A Cat's eye (AMBER) AA R.H. cover (RED) AG R.H. cover (METALLIC DARK GREY) AT R.H. cover (BLACK) A Series of belts A Pannier locks kit AA L.H. cover (RED) AG L.H. cover (METALLIC DARK GREY) AT L.H. cover (BLACK) A L.H. handle A Insulation 2 09

112 DRAWING 047 Antilock braking system (abs)

113 DRAWING 047 Antilock braking system (abs) NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY A Screw A Speed sensor A Gasket th B Screw A Special screw A Gasket th A Caliper holder plate.4.05.a CPU - rear caliper line A ABS unit A Screw A Rear phonic wheel Hose guide A Bracket A Screw A Rear master cylinder - CPU line a Front master cylinder - CPU line A CPU - front calipers line A Front phonic wheel A Pad B Holder A Holder A Screw 2

114 DRAWING 04 Evaporative emissions canister

115 DRAWING 04 Evaporative emissions canister NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY A Hose guide A Tube A Hose guide A Holder B Spacer A Nut A Rubber pad A Plate B Screw A Canister filter A Tube A Tube A Tube A Aluminium gasket th B Union B Hose guide A Breather pipe Shunt valve A Hose guide A Clamp A Hose guide

116 DRAWING 049 Data plate positions 2 4 4

117 DRAWING 049 Data plate positions NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY 4..5.A Sticker A Label A Sticker A Sticker 5

118 Index CODE No. Drwg. POS. N. CODE No. Drwg. POS. N. CODE No. Drwg. POS. N. CODE No. Drwg. POS. N. CODE No. Drwg. POS. N A A A A A A A B B A A B A A A B A A B A A B A B B A B B A A B A A A A 0a A A A A A A A A 0a A A A 0a A A BB 0a A A A 0a A A A A A A A A A A A A A A A A A A A A G A A A AB A A A AC A A AA 04 7 A

119 Index CODE No. Drwg. POS. N. CODE No. Drwg. POS. N. CODE No. Drwg. POS. N. CODE No. Drwg. POS. N. CODE No. Drwg. POS. N AG A A.004.AC C A AT A A A A AA AB A A A AG AB A A A AT AC B A A A 02a AC A A A BC 0a AD A A B AE 0a AD A A A BB A A A AA A 0a A A A AB A AB A A AA A AB A A AB A 0a AC B A AA A AC A A B A AD A A A A AD A A 02a A A 0 04.A.00.A B A 02a A A A.00.A B C A B A.00.AB C A A A 0 04.A.00.AB A C A B 0 04.A.00.AC A A A A A.00.AC A B A A A.004.A C A A D A.004.A A B A A.004.AB A A A C A.004.AB A A A C A.004.AC B A A B

120 Index CODE No. Drwg. POS. N. CODE No. Drwg. POS. N. CODE No. Drwg. POS. N. CODE No. Drwg. POS. N. CODE No. Drwg. POS. N A BG AA BT A 00d A BT AB A A 00d A B AE A A 00d B BA AA A A A BG AB AB A A BT AE A A AA BA A A A 0a AB BG A A A AF BT A A A A A B A B A D B B A AB A 00d A A AA AB A 00d A C AG B A 00d B D AT AA A 00d A D B AG A 00d B A A AT A 00d A A AA A A A A AG A A A AA AT A AB C AG AA A B A AT AG A C 02a A A AT A BA A A AA A BG A A AG D BT B B AT A BA A A BA A BG A 00d A 07 C