GENERAL INFORMATION The present spare parts order exactly the right spare parts. When ordering specify:

Transcription

1 GENERAL INFORMATION The present spare parts order exactly the right spare parts. When ordering specify: 1) the part's code number followed by its description; 2) the motorcycle's serial number, stamped on the steering head. Reference to right and left apply to the vehicle in terms of its direction of movement. VALIDITY f.m. d.m. f.m.m. d.m.m. Until V.I.N. From V.I.N. Up to engine number From engine number RED motorcycle BLACK motorcycle YELLOW motorcycle GREY motorcycle BLEU motorcycle All data are subject to modification without prior notice. Ducati Motor Holding S.p.A. Uffici Commerciali Amministrativi: Via A. Cavalieri Ducati n. 012 Bologna, Italy Telefono Fax Internet 1

2 2

3 page CONTENTS a 8 001b c d a a a a b a a a a WORKSHOP SPECIAL TOOLS WORKSHOP SPECIAL TOOLS WORKSHOP SPECIAL TOOLS DIAGNOSIS TESTER MATHESIS WORKSHOP SPECIAL TOOLS GEARCHANGE GEAR-BOX CLUTCH CLUTCH COVER CLUTCH COVER CRANKSHAFT CYLINDERS - PISTONS TIMING FILTERS AND OIL PUMP HALF CRANKCASES HALF CRANKCASES WATER PUMP - ALTERNATOR COVER ELECTRIC STARTER AND IGNITION HEAD: TIMING COLLECTORS AND HEAD COVERS HEAD COVERS HEAD OIL COOLER THROTTLE BODY INJECTION CONTROL UNIT BATTERY BOX MOUNT INJECTION SYSTEM EXHAUST SYSTEM INSTRUMENT PANEL FRONT HEAD-LIGHT HALF-HANDLEBARS - SHOCK-ADSORBER FRONT FORK FRAME CLUTCH CONTROL FRONT HYDRAULIC BRAKE REAR HYDRAULIC BRAKE FRONT AND REAR WHEELS REAR WHEEL PIN REAR FRAME-REAR FOOT RESTS REAR SUSPENSION AIR INDUCTION-OIL VENT WATER RADIATOR ASSY COOLING CIRCUIT FUEL TANK FUEL SYSTEM SEAT SEAT HEADLIGHT FAIRING FAIRING FUEL INFEED MARKING PLATES

4 WORKSHOP SPECIAL TOOLS

5 001 WORKSHOP SPECIAL TOOLS NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY Head nuts holder wrench Wrench for removing oil filter cartridge Spacer for checking lower valve shim Degree wheel holder tool for ignition advance check Degree wheel Fork feeler gauge 0.1 mm Fork feeler gauge 0.2 mm Fork feeler gauge 0. mm Timing belt control gauge Check intrument Check intrument Check intrument Check intrument Check intrument Flywheel Wrench Bench for engine repair Engine canvas Plate for positioning gear engagement fork Wrench to hold cluch housing drum steady Sleeve for installing clutch bell gear Tool to drive valve seal ring ø Head nuts holder wrench Head mounting base 1 5

6 001a WORKSHOP SPECIAL TOOLS

7 001a WORKSHOP SPECIAL TOOLS NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY Closing rocker pre-load kit Rocker spring pre-load compound kit Driving roller tightening tool Primary drive gear tightening tool Valve lift gauge Bush Tool to hold crankshaft in TDC position Tool to fit O-rings onto stud bolts Wrench to tighten tensioning bolts Rocker shaft extractor Seal ring driving tool T.D.C. control gauge Drive roller puller Belt roller timing tool Union for exhaust gas suction Tool to fit oil seal 1 7

8 001b WORKSHOP SPECIAL TOOLS

9 001b WORKSHOP SPECIAL TOOLS NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY Stopper for driving the half bearing of the steering head base Tool for balancing rear wheel A Coupling Stopper for disassembling the swingarm pivot Tool for assembling the swingarm ball bearings Wrench for adjusting the steering head Wrench for assembling the steering head cap Wrench for front wheel spindle Tool for assembling the steering head bearings Stopper for assembling the rocker needle bearings A Geometry adjustment kit Tool for holding SHOWA fork spacer Tool for assembling chain Tool for overhauling SHOWA forks - assembling seal ring Stopper for inserting the steering damper bearing Wrench for seat lock nut Stopper for assembling the rear fork roller bearings Wrench for adjusting the eccentric hub

10 001c DIAGNOSIS TESTER MATHESIS

11 001c DIAGNOSIS TESTER MATHESIS NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY Z Bare Mathesis A Italian manual B English manual C German manual D Franch manual E Spanish manual R Main cable Mathesis A Pickup Control cable Q Battery mains cable Mains cable adapter for self diagnosis N Sensor for absolute pressure sampling V Amperometer plier E Adapter for wires Pickup test cable P Sensor for air temperature sampling C Cable for potentiometer adjustement B Test cable and speed indicator adjustement F Adapter for 2 wires Pickup test cable D Adapter for potentiometer adjustement A Sensor for small throttle potentiometer sampling H Sensor for throttle potentiomer sampling G Sensor for air/water temperature sampling M Sfety remote switch L 2 Wires sampling Pickup sensor U Case with sponge Italian memory card English memory card German memory card French memory card Spanish memory card S DUCATI sticker for case T DUCATI sticker RH/LH side 1 11

12 001d WORKSHOP SPECIAL TOOLS

13 001d WORKSHOP SPECIAL TOOLS NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY Check intrument 1 GB Check intrument 1 D Check intrument 1 F Check intrument 1 E Check intrument A Fuel pressure line HS A Fuel pressure line ST/SS/M A Oil pressure line A Fitting - cylinder compression M A Fitting - cylinder compression M A Cable Volt PF DUC A Pressure sensor A Oil pressure fitting A Cable for supplementary tests A Red clamp cable A Black clamp cable A Temperature probe A Main cable PF A A Electric lighter connection adapter (ST) A Battery connection adapter A Red case with sponge rubber T DUCATI sticker RH/LH side 2 1

14 OIL FILTER GEARCHANGE 1

15 002 GEARCHANGE NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY A Return spring A Washer A Special screw A Gear stopper assembly A Gasket th A Switch A Push rod holder Gasket Gear selector spring Ball A 1st,th-2nd,rd gear selector fork A 5th,6th gear selector fork Fork pin A Shim th Circlip A Needle retaining ring (square cross-section) A Special roller (square cross-section) A Complete gearbox drum Shim th A Shim th A Fork return spring Shim th Shim th Ring A Nut A Gearbox drum control fork Gearchange lever pin A Pin with gearchange lever Gearchange lever return spring N Screw A Washer C Screw A Washer A Centering ring A Stopper plate Shim th Shim th

16 LATO FRIZIONE LATO CATENA 1» 5»»» 6» 2» 1» 5»»» 6» 2» GEAR-BOX

17 00 GEAR-BOX NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY Shim th Shim th A Gearbox main shaft Shim th A Needle bearing C Driving gear 5th sp A Grooved washer th Snap ring C Driving gear rd/th sp C Driving gear 6th sp B Driving gear 2nd sp Shim th Shim th A Shim th B Shim th E Shim th F Shim th A Chain sprocket Z= A Lock washer A Nut Shim th Shim th Shim th Shim th A Shim th A Shim th E Shim th A Complete lay shaft Needle bearing B Driven gear 1st sp Shim th C Driven gear 5th sp C Driven gear th sp C Driven gear rd sp C Driven gear 6th sp B Driven gear 2nd sp A Gearbox lay shaft Shim th Shim th A Complete main shaft Seal ring Needle bearing A Grooved washer th A Spacer A O-ring 1 17

18 00 CLUTCH

19 00 CLUTCH NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY Clutch spring A Retainer A Clutch control pin B Screw A Lock washer B Rubber pad B Plate holder hub A Clutch plates set B Lock washer B Clutch drum Screw A Pressure plate A Clutch housing A Bearing A O-ring A Seal ring A Clutch/crankshaft gears pair A Bearing A Circlip - spacer Bearing Spacer A Piston assembly A Bush Pin B Nut O-ring O-ring N1075 Screw A Clutch control rod O-ring B Spacer O-ring 1 19

20 005 CLUTCH COVER

21 005 CLUTCH COVER NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY AD Clutch protection cover N Screw B Screw A Oil level inspection porthhole N Screw A Ring O-ring A Screw A Switch Gasket th A Cap O-ring Locating bush A Clutch cover gasket 1 21

22 005a CLUTCH COVER

23 005a CLUTCH COVER NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY Bush A Seal ring A Shim th A Circlip Fluid sealant A Cover clutch side A Threaded dowel 1 2

24 006 CRANKSHAFT Rif. 17 Tav

25 006 CRANKSHAFT NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY B Crankshaft A Special screw A Cap Threaded dowel A Connecting rods pair Grease A Spacer BA Half-bearing (RED) BB Half-bearing (BLUE) A Special screw Woodruff key A Shim th B Shim th C Shim th D Shim th. 2, E Shim th. 2, F Shim th. 2, G Shim th H Shim th I Shim th J Shim th K Shim th. 2, L Shim th. 2, M Shim th N Shim th A Lock washer A Nut A Nut A Spring washer 1 25

26 007 CYLINDERS - PISTONS GENUINE PARTS Part - code N. Quantity N. Made in Italy

27 007 CYLINDERS - PISTONS NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY A Complete piston ø A Piston pin circlip A Piston pin A Piston rings set N1075 Screw A Stud bolt A O-Ring A Cover A Cover A Cylinder-piston fit A Head-cylinder gasket A Bush A Cylinder-crankcase gasket th A Water inlet union to cylinders A Clamp A Horizontal cylinder water inlet hose A Vertical cylinder water inlet hose A Gaskets set 1 27

28 008 TIMING FISSO MOBILE

29 008 TIMING NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY A Vertical belt outer cover A Outer central cover A Horizontal belt outer cover N01 Screw A Setscrew A Bush C Tensioner eccentric FN1 Nut A Spacer A Timing lay shaft A Snap ring Woodruff key B Timing gears pair Lock washer Hexagon nut Woodruff key A Spacer B Timing belt roller A Belt roller separating washer A Spacer Elastic-stop ring nut A Timing drive toothed belt A Fixed tensioner roller pin C Movable tensioner roller pin Bearing Circlip 29

30 009 FILTERS AND OIL PUMP

31 009 FILTERS AND OIL PUMP NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY A Complete oil pump A Pump cover A Screw A Aluminium gasket A Pump body A Screw B Woodruff key B Screw A Spring washer N Screw A Spring washer A Pump drive gear A Bush A Bypass spring Locating bush A Gasket Oil drain plug with magnet A Gasket th.1, A Oil filter Oil filter cartridge Nipple O-ring A Cap Snap ring Circlip Reduction bush A Cap Gasket th A Bypass valve A Bypass spring A Bypass cap A O-ring A Cap 1 1

32 010 HALF CRANKCASES OIL 5 FILTER 2

33 010 HALF CRANKCASES NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY A Complete half-crankcases pair A Aluminium gasket A Screw A Bearing holder bush Bearing Locating dowel A Bearing O-ring Circlip A Screw B Breather valve O-ring O-ring Nut A Special washer A Stud bolt for fastening head cylinder Screw A Keep plate A Bearing A Seal ring Bearing Washer 1

34 010a HALF CRANKCASES

35 010a HALF CRANKCASES NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY A Bearing Bearing Fluid sealant A Spacer N Screw A Cap A Bush Seal ring Bearing Circlip Bearing A Bearing holder bush A Screw B Screw B Screw A Special screw B Screw 2 5

36 011 WATER PUMP - ALTERNATOR COVER

37 011 WATER PUMP - ALTERNATOR COVER NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY B Generator AE Chain cover 1 60N1075 Screw A Bearing B Screw N Screw A Washer A A 10 Ring A Bearing A O-ring A Bearing Fluid sealant BB Generator cover Locating bush N Screw A Water pump delivery filler Circlip Seal ring N Screw B Screw Locating dowel A O-ring BC Cover C Screw A Ignition inspection cap A Seal B Spacer B Mechanical seal B Water pump fan A Gasket AB Complete water pump cover A Gasket th A Cap A Washer A Bracket B Screw A Screw A Sensor AA Gasket th.0, AB Gasket th.0, AC Gasket th.1, B Screw N01 Washer A Holder 1 7

38 012 ELECTRIC STARTER AND IGNITION

39 012 ELECTRIC STARTER AND IGNITION NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY A Complete starter motor (8-9 included) N01 Spring washer A Nut A Starter motor gasket N Screw A Starter motor sprocket Circlip Intermediate gear pin A Washer A Intermediate gear assembly Circlip B Screw A Flange A Locating pin Check ring B Ignition flywheel Washer C Inner ring A Needle bearing A Electric starter driven gear A Starter clutch 1 9

40 01 HEAD: TIMING 5 Registro bilanc. apertura Adjustment Réglage Ventilkäppchen A 1, A 1, A 1, A 1, A A 2, A 2, A 2, A 2, A 2, A 2, A 2, A 2, A 2, A 2, A 2, A 2, A 2, A 2, A 2, A 2, A 2, A 2, A 2, A A, A, A, A, A, A, A, A, A,5 7 Registro bilanc. chiusura Adjustment Réglage Ventilkäppchen B 2, B 2, B 2, B 2, B 2, B 2, B B, B, B, B, B, B, B, B, B, B, B, B, B, B,

41 01 HEAD: TIMING NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY A Closing rocker shaft A Exhaust opening rocker shaft A Opening rocker A L.H. Closing rocker A See table E Split rings B See table A Rubber pad A Exhaust valve guide AB Oversize valve guide AC Oversize valve guide AD Oversize valve guide A Exhaust valve seat AB Oversize exhaust valve seat AC Oversize exhaust valve seat A Exhaust valve A Intake valve guide AB Oversize valve guide AC Oversize valve guide AD Oversize valve guide A Intake valve seat AB Oversize intake valve seat AC Oversize intake valve seat A Intake valve A Closing rocker shaft A R.H. Closing rocker A Intake opening rocker shaft A R.H. valve return spring A L.H. valve return spring A Threaded dowel A Stud bolt 8 1

42 01 COLLECTORS AND HEAD COVERS

43 01 COLLECTORS AND HEAD COVERS NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY A Cover A Cover 1 60N1075 Screw O-ring A O-ring A Gasket Screw A Copper gasket A Clamp A Intake manifold B Screw 2

44 01a HEAD COVERS

45 01a HEAD COVERS NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY A Cover A Cover 1 60N1075 Screw A O-ring A Gasket O-ring A Union B Screw 1 5

46 015 HEAD

47 015 HEAD NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY A Head (,5,1,16 included) A Stud bolt A Special screw A Bush N Screw A Cover A Nut A Washer A Head gasket A Bush A Pin A Special screw N1075 Screw B Horizontal exhaust camshaft B Horizontal intake camshaft A O-ring A Seal ring B Vertical exhaust camshaft A Woodruff key B Vertical intake camshaft A Spacer A Timing belt roller A Washer A Ring nut A Screw A Cap A Cap 7

48 016 OIL COOLER

49 016 OIL COOLER NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY C Oil return pipe A O-Ring A Nipple C Oil delivery pipe A Special screw A Head lubrication pipe A Gasket th A Special screw B Holder N Screw Spacer N01 Washer Nut A Cap A Special screw A Oil cooler A Vibration damper pad Spacer Screw A Special screw A Aluminium gasket A Nipple 2 9

50 017 THROTTLE BODY F 50

51 017 THROTTLE BODY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY A Plate A Special screw A O-ring A Injectors kit with hose A Complete throttle body A Potentiometer A Washer A Screw 2 51

52 018 INJECTION CONTROL UNIT

53 018 INJECTION CONTROL UNIT NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY A Injection control unit A Plate A Special screw D Battery grounding cable Nut A Clamp Clamp A Cap A Screw N01 El-stop nut A Stud bolt A Spacer Vibration damper pad A Washer 2 5

54 018a BATTERY BOX MOUNT

55 018a BATTERY BOX MOUNT NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY A Battery box mount A Plate A Screw B Rubber holder A Relay A Flashing device A Battery C Regulator Screw FN1 Nut A Spring washer A Nut B Solenoid starter-starter motor cable B Battery-solenoid starter cable A Remote switch Vibration damper pad Screw A Panel B Battery carpet A Quik fastening A Rubber cap 1 55

56 018b INJECTION SYSTEM

57 018b INJECTION SYSTEM NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY A Wiring A Holder A Coil B Screw Vibration damper pad A Screw Washer Spacer A Clamp A Clamp A Clamp Clamp A Head spark plug wiring A Head spark plug wiring A Plate "NON RIMUOVERE" A Wiring B Spark plug A Fuse 0A A Screw A Pin A Fuse A A Fuse 7.5A A Fuse 15A A Fuse 0A A Fuse 20A A Fuse 10A A Case cover A Sticker schema fusibili Connector End section Connector 1 57

58 019 EXHAUST SYSTEM

59 019 EXHAUST SYSTEM NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY A Exhaust gasket A Exhaust manifold A Nut A Spring A Spacer A Holder A Vibration damper pad A Screw A Horizontal head exhaust pipe Washer Screw A Vertical head exhaust pipe Spacer A Washer A Protection BB Screw A R.H. silencer A Exhaust manifold A L.H. silencer A Spacer Screw A Screw B Gasket A Clamp Nut A Spacer A Cap Nut A Exhaust pipe A Gasket th A Screw 2 59

60 020 INSTRUMENT PANEL

61 020 INSTRUMENT PANEL NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY A O-ring A Sensor B Screw 2 8B Screw A Speedometer transmission BC Headlight holder A Holder B Screw A Holder Nut Rubber pad GB B Complete instrument panel (speedometer - miles) A Wiring Warning lamp bulb12v-2.1w Warning lamp bulb12v-1.2w Nut Washer A Rubber pad A Screw Grip B Speedometer holder Gasket A Speedometer 1 GB A Speedometer/Speedometer miles Tachometer holder Vibration damper sponge A Tachometer A Water thermometer ( C) A Instrument panel wiring B Screw 2 61

62 021 FRONT HEAD-LIGHT Dx 28 Sx 62

63 021 FRONT HEAD-LIGHT NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY B Complete headlight B Screw Bulb Bulb A Cover gasket A Cover A Headlight cover B Screw A Vibration damper Bulb A Headlight cover Bulb A Electric wiring B Screw A R.H. plate A Spring A L.H. plate A Front wiring A Plate A Screw AB Horn (BLACK) A Spacer Screw Vibration damper pad A Clamp Clamp Turn indicator Turn indicator A Cup A Plate A Rubber holder A Relay 2 6

64 022 HALF-HANDLEBARS - SHOCK-ADSORBER STOP RUN ON OFF

65 022 HALF-HANDLEBARS - SHOCK-ADSORBER NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY A Steering head base assembly A Seal ring A Bearing A Tube A Throttle control Grips pair A L.H. handlebar A L.H. switch O-ring A Key-operated switch A Screw B Screw A Washer B Screw A Circlip A Special screw A Ring nut A Spacer B Screw B Holder A Steering damper B End section A Steering head A Cap B Screw B Screw A R.H. switch A Throttle control transmission A Screw Screw B Cover A Wrench A Cap 2 706N01 Washer A R.H. handlebar A Starter control transmission return spring A Starter control Screw 2 65

66 022a FRONT FORK Dx Dx 5Dx Sx 1Sx 66

67 022a FRONT FORK NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY A L.H. fork leg assembly 1 2 8A Screw Clamp Clamp A R.H. fork leg assembly C Complete L.H. slider A Adjusting screw A Special washer C Complete R.H. slider A Dust seal A Seal ring A Check ring A Bush C Stanchion tube A Bush A Centering ring B Damper tube A Flexible collar A Special washer D Spring A Spring coupling A Slider A Rubber cush drive hub C Complete cap A Snap ring A Ring 2 67

68 02 FRAME

69 02 FRAME NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY AA Frame A Nut A Spring A Pin A Front R.H. foot peg B Screw A Screw A Protection A R.H. foot peg holder plate A Ring A Protection A Front L.H. foot peg A0.558 Pin B Screw A Washer A Screw Bush A Rubber pad A Gearchange lever A Gearchange control lever N01 El-stop nut Ball joint A L.H. nut A Switch N Nut Ball joint A Gearbox transmission rod assembly A L.H. foot peg holder plate A Screw A Plate A Nut A Plate A Complete spring Inner spring A Plate B Screw A Pin A Side stand A Spacer 2 69

70 02 CLUTCH CONTROL

71 02 CLUTCH CONTROL NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY AB Clutch drive pump A Lever with dowel A Spare lever pin A Spare bracket A Spare union B Screw A Screw Vibration damper pad A Plate N02 Screw A Cap Complete oil tank Nut A Clamp A Tube A Special screw A Gasket th A Clutch control pipe (METAL PLAITED) A Filler Bleed A Dust seal 1 71

72 2 025 FRONT HYDRAULIC BRAKE

73 025 FRONT HYDRAULIC BRAKE NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY A Front brake pump B Lever with dowel A Spare lever pin A Spare pins and spring A Microswitch B Screw C R.H. brake caliper A Gasket th A Spare bleed union A Spring A Special screw A Dust seal A Tube Spare cap Complete oil tank A Clamp A Screw Vibration damper pad N02 Screw A Spare bracket Spare union A Bracket A Caliper pump pipe (METAL PLAITED) B Screw B Pads pair C L.H. brake caliper FN1 El-stop nut 1 7

74 026 REAR HYDRAULIC BRAKE

75 026 REAR HYDRAULIC BRAKE NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY A Holder B Screw A Washer Circlip Bush A Brake control lever N Nut Threaded dowel A Pedal pin A Rubber pad A Screw A Rear brake pump A Pin A Fork A Adjuster rod A Clamp A Tube Complete oil tank Spare cap N02 Screw B Switch A Special screw A Gasket th A Spare union A Dust cover A Pads pair C Rear brake line (METAL PLAITED) Screw A Rear brake caliper A Dust seal Spare bleed union A Spare pins and spring B Spring 1 75

76 027 FRONT AND REAR WHEELS

77 027 FRONT AND REAR WHEELS NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY A Nut Washer A Speedometer transmission B Screw A Brake disc Seal ring Relay drive ring Bearing A Inner spacer AA Front rim A Front wheel spindle A Clip A Nut A Washer A Washer AA Rear wheel rim Valve A Valve A Stand A Motrocycle's canvas cover (RED) 1 77

78 028 REAR WHEEL PIN

79 028 REAR WHEEL PIN NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY A Clip A L.H. nut A Washer A Nut C Complete rear sprocket flange A Washer A Bush A Bush A Rubber cush drive hub A Ring gear z= A Pin A Spacer A Hub A Chain (9 Links) A Washer A O-Ring A Caliper holder plate A Circlip A Final drive kit B Rear brake disc A Screw B Screw 79

80 029 REAR FRAME-REAR FOOT RESTS Sx 0 Dx Sx 2 Dx Sx 8 Dx Sx 1 Dx 80

81 029 REAR FRAME-REAR FOOT RESTS NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY AB Rear frame Vibration damper pad Threaded insert Nut B Screw A Lock latch A Rear L.H. foot peg A Rear R.H. foot peg A Tool box C Panel (BLACK) Fairlead A Number plate holder A Plate A Clamp A Plate Nut A Screw A Tool bag E Owner's manual 1 E E Owner's manual 1 J F Owner's manual A Seat lock A Nut A Nut 2 80C Shim C Screw Self-tapping screw A Hook A Helmet anti-theft wire A Tail lamp B Screw Turn indicator Turn indicator Bulb A Cup Nut N11558 Washer Clamp A Locks kit A Screw A L.H. protection A R.H. protection A Rear L.H. foot peg holder plate A Rear R.H. foot peg holder plate B Screw A Pin Ring Spring N Ball Bulb A Washer A Fairlead A Nut A Washer 81

82 029 REAR FRAME-REAR FOOT RESTS Sx 0 Dx Sx 2 Dx Sx 8 Dx Sx 1 Dx 82

83 029 REAR FRAME-REAR FOOT RESTS NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY A Holder A Cat's eye 2 8

84 REAR SUSPENSION

85 00 REAR SUSPENSION NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY B Shock absorber C Shock absorber A Tie rod Ball joint A Nut Ball joint A Nut A Bush A Rocker assembly A Needle bearing A Seal ring B Screw B Screw A Spacer A Screw FF1 Nut Washer A Screw A Bush A Swingarm Needle bearing Seal ring Bearing A Inner spacer A Pin A Upper chain sliding shoer A Lower chain sliding shoe Spacer Screw A Cap A Cap A Screw A Outer spacer A Bush A Bush A Screw A Washer A Swingarm pivot A Bracket A Screw A Protection A Chain guard A Chain adjustment sticker 1 J B Chain adjustment sticker A Spacer 85

86 01 AIR INDUCTION-OIL VENT

87 01 AIR INDUCTION-OIL VENT NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY AA Air box (RED) AB Air box (YELLOW) Rubber pad A Hook B R.H. air filter box B Screw A R.H. filter case cover A R.H. air filter A L.H. restriction B Shear rivet A R.H. gasket A Gasket A Exhaust pipe A Quik fastening B Airbox-tank gasket A Special screw A Special screw A Breather pipe Clamp B Oil breather tank Insert A Plate A Screw A Screw Clamp A Breather pipe B Clamp A R.H. restriction A Washer A L.H. filter case cover A L.H. air filter B L.H. air filter box A L.H. gasket A Seal A Panel 2 87

88 02 WATER RADIATOR ASSY

89 02 WATER RADIATOR ASSY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY A Water radiator A Electric fan A Screw A Vibration damper pad Spacer Screw A Holder A Special screw 1 89

90 A A COOLING CIRCUIT

91 0 COOLING CIRCUIT NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY A Water tank A Tank cap B Filler O-ring N02 Screw A Clamp A Tube A Breather pipe A Tube A Clamp A Clamp A Water tank A Union A Holder AB Union O-ring A Gasket th Thermistor A Sensor A Cap A Gasket N1075 Screw A Hose A Thermostat A Screw A Hose A Rubber pad A Cooler/thermostat hose A Hose A Clamp Clamp A Thermostat/pump hose A Union/head hose A Clamp 6 91

92 0 FUEL TANK

93 0 FUEL TANK NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY AA Fuel tank (RED) AB Fuel tank (YELLOW) BA Fuel tank (unpainted) A Screw A Gasket E Screw A Tank cap A Special screw A Spacer A Rubber pad A Clamp A Exhaust pipe A Special screw 1 706N01 Washer A Rubber pad AA Sticker "DUCATI" (RED) AB Sticker "DUCATI" (YELLOW) Screw B Front connection Screw A Gasket th B Screw A Tube A Breather pipe A Union A Breather pipe A Fuel pipe A Holder A Holder AA Sticker alloro Ducati AB Sticker alloro Ducati Spacer 1 9

94 0a FUEL SYSTEM

95 0a FUEL SYSTEM NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY A Flange A Gasket th A Cap A Clamp A Filter/pump pipe B Fuel filter A Holder Hexagon nut A End section A Tube A O-ring Self-tapping screw Screw A Fuel pump B Pump holder A Tube A Air separator A O-ring A Tube A Fuel pump filter A O-Ring A Pressure regulator Circlip B Tank wiring A Gasket A End section B Manifold A Snap ring 1 95

96 05 SEAT 1 0 Dx 1 Sx Dx 5 Sx 22 Dx 2 Sx

97 05 SEAT NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY AA Rear fairing (RED) AB Rear fairing (YELLOW) A Screw A Sticker "DUCATI SUPERBIKE" (RED) AB Sticker "DUCATI SUPERBIKE" (YELLOW) A Holder 1 5 8H Screw A Rubber pad N11558 Washer Nut A Rubber pad A Pin A Linkage B Seat N10282 Screw A Bracket A Nut A Spring A Spacer A Rubber pad B Screw A Bracket A Sticker A R.H. pad A L.H. pad A Plate A Plate Screw A Pin A Rubber pad A Tail lamp Lens A Two-light bulb 12V 5/21W A Cat's eye A Holder A Washer A Screw A Vibration damper pad A Spacer B Pillion rider seat (RED) BC Pillion rider seat (YELLOW) A Rear fairing (unpainted) A R.H. bracket A L.H. bracket A Bent plate 2 60N Screw B R.H. protection B L.H. protection 1 97

98 05a SEAT Dx 2 Sx Dx Sx 22 Dx 2 Sx

99 05a SEAT NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY AA Rear fairing (RED) AB Rear fairing (YELLOW) A Spacer A Sticker "DUCATI SUPERBIKE" (RED) AB Sticker "DUCATI SUPERBIKE" (YELLOW) A Holder 1 5 8H Screw A Rubber pad N11558 Washer Nut A Rubber pad A Pin A Linkage A Seat N10282 Screw A Bracket A Nut A Spring A Spacer A Rubber pad B Screw A Bracket A Rear fairing (unpainted) A R.H. pad A L.H. pad A Plate A Plate Screw A Pin A Rubber pad A Tail lamp Lens A Two-light bulb 12V 5/21W A Cat's eye A Holder A Washer A Screw A Vibration damper pad A Spacer A Screw Plastic rivet AA GOLD sticker A R.H. protection A L.H. protection B R.H. protection B L.H. protection 1 99

100 06 HEADLIGHT FAIRING

101 06 HEADLIGHT FAIRING NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY BA Headlight fairing (RED) BB Headlight fairing (YELLOW) A Headlight fairing (unpainted) A Special screw A R.H. rear-view mirror A Gasket A Fairing fastening kit A Windshield Screw AB R.H. mirror holder Screw Spring A Shear rivet AB L.H. mirror holder A L.H. rear-view mirror Threaded insert Nylon washer A R.H. protection A L.H. protection 1 101