DUCATI M 750. GENERAL INFORMATION The present spare parts list enables one to order exactly the right spare parts. When ordering specify:

Transcription

1 GENERAL INFORMATION The present spare parts list enables one to order exactly the right spare parts. When ordering specify: ) the part s code number followed by its description; 2) the motorcycle s serial number, stamped on the steering head. Reference to right and left apply to the vehicle in terms of its direction of movement. VALIDIT f.m. d.m. f.m.m. d.m.m. Until V.I. From V.I. Up to engine number From engine number RED motorcycle GREY motorcycle BLACK motorcycle YELLOW motorcycle BLUE motorcycle All data are subject to modification without prior notice. MOTOR S.p.A. Uffici Commerciali Amministrativi: Via A. Cavalieri Ducati n Bologna, Italy Telefono Fax Internet

2

3 CONTENS 5 00 WORKSHOP SPECIAL TOOLS WORKSHOP SPECIAL TOOLS GEARCHANGE 003 GEAR-BOX CLUTCH CLUTCH COVER CRANKSHAFT CYLINDERS - PISTONS TIMING FILTERS AND OIL PUMP HALF CRANKCASES 27 0 ALTERNATOR COVER ELECTRIC STARTER AND IGNITION 3 03 HEAD : TIMING VERTICAL HEAD HORIZONTAL HEAD INLET DICT FUEL INFEED 4 08 CARBURETOR CARBURETOR ELECTRIC SYSTEM IGNITION SYSTEM EXHAUST SYSTEM INSTRUMENT PANEL FRONT HEAD-LIGHT PLATE HOLDER - REAR LIGHT FORK FRONT AND REAR WHEELS HALF HANDLEBARS FRONT BRAKE REAR BRAKE FRAME GEARCHANGE LEVER - FOOT REST REAR FORK REAR SUSPENSION AIR INDUCTION - OIL VENT OIL COOLER FUEL TANK SEAT FUEL INFEED MARKING PLATES 3

4 80 M 750 WORKSHOP SPECIAL TOOLS

5 WORKSHOP SPECIAL TOOLS NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY Clutch drum holder wrench Rocker shaft extractor A Torque wrench for timing belt Head nuts holder wrench Alternator holder wrench for tightening nut Crankshaft gear holder wrench for tightening nut Tool for assembling closing rocker and spring Degree wheel Degree wheel holder tool for ignition advance check Tool to assemble the steering pipe bearings Sleeve for installing clutch bell gear Extractor for removal of chain/generator cover Pin for assembling rocker arms Timing belt rollers holder wrench Spacer for checking lower valve shim Spacer for checking lower valve shim Wrench for removing oil filter cartridge Fork feeler gauge 0. mm Fork feeler gauge 0.2 mm Fork feeler gauge 0.3 mm Union for exhaust gas suction T.D.C. control gauge Extractor bushing bearing inner ring Crankcases assembling cap Valve lift gauge Extractor for primary drive gear Plate for positioning gear engagement fork Conversion kit for 4V belts tensioning tool 5

6 . WORKSHOP SPECIAL TOOLS

7 . WORKSHOP SPECIAL TOOLS NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY Tool for overhauling SHOWA forks - assembling seal ring Wrench for front wheel spindle Tool for assembling chain A Coupling Frame/engine mount Stopper for driving the half bearing of the steering head base Tool for holding SHOWA fork spacer 7

8 2 GEARCHANGE

9 2 GEARCHANGE NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY A Return spring A Washer A Special screw A Gear stopper assembly A Copper gasket Gasket th., Gasket th A Gasket th A Switch Push rod holder Gasket Gear selector spring Ball st,3rd-2nd gear selector fork th,5th gear selector fork Fork pin A Shim th Neutral light operating pin A Needle retaining ring (square cross-section) A Special roller (square 6 cross-section) A Complete gearbox drum Shim th A Shim th A Fork return spring Washer Shim th Ring A Nut A Gearbox drum control fork Gearchange lever pin A Pin with gearchange lever Gearchange lever return spring 28 60N02509 Screw A Washer B Screw A Washer A Centering ring A Stopper plate Shim th Circlip 9

10 3 GEAR-BOX

11 3 GEAR-BOX NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY Shim th Shim th A Shim th E Shim th B Shim th Needle bearing A Driven gear st sp Shim th A Driven gear 4th sp Snap ring A Grooved washer th A Driven gear 3rd sp A Needle bearing A Driven gear 5th sp A Driven gear 2nd sp Shim th A Gearbox lay shaft A Shim th A Chain sprocket Z= A Sprocket keep plate C Screw N0 Spring washer Driving gear 2nd sp A Driving gear 5th sp A Driving gear 3rd sp A Driving gear 4th sp B Gearbox main shaft Shim th B Shim th D Shim th., Shim th F Shim th Shim th AG Shim th Shim th AB Shim th Shim th AD Shim th., A Complete lay shaft B Complete main shaft AH Shim th Shim th AL Shim th., Shim th AN Shim th.,3

12 4 CLUTCH

13 4 CLUTCH NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY B Screw A Retainer B Clutch control pin Clutch spring A Pressure plate A Bearing B Clutch plates set A Nut A Lock washer A Clutch drum A Shim B Primary drive gears pair A Inner ring A Bearing A Spacer A Clutch control rod A Rod protection cover O-ring Seal ring A Seal ring B Piston assembly A Spring A Clutch cap 24 60N07335 Screw 3 3

14 5 CLUTCH COVER ,,, yyy,,, yyy

15 5 CLUTCH COVER NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY AB Cover clutch side (GREY) B Screw B Screw A Oil level inspection cap 5 60N0250 Screw A Panel B Screw Bush Seal ring A Shim th Circlip O-ring Locating bush O-ring A Cap N0 Washer A Holder Spacer N02 Screw Gasket A Switch A Holder A Cover 5

16 6 CRANKSHAFT Rif. 7 Tav

17 6 CRANKSHAFT NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY A Crankshaft A Special screw A Cap Threaded dowel A Connecting rods pair (6-7-8 included) Standard bush Pin Standard half-bearing Undersize half-bearing Undersize half-bearing A Special screw Woodruff key A Shim th A Shim th A Shim th A Shim th A Shim th A Shim th Lock washer Nut A Complete connecting rods assembly A Spring washer A Nut Woodruff key 7

18 7 7 CYLINDERS - PISTONS GENUINE PARTS Part - code Quantity Made in Italy 5 6,,,,,,,

19 7 CYLINDERS - PISTONS NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY O-ring A O-ring Piston pin A Vertical cylinder-piston fit O-ring A Cylinder-crankcase gasket th Bush A Horizontal cylinder-piston fit A Complete piston Piston pin circlip A Piston rings set A Head-cylinder gaskets set A Copper gasket Screw 2 9

20 8 TIMING ,,, yyy ,, yy 4,,, yyy,, yy 6,, yy,, yy,, yy,, yy ,,, yyy,, yy 2,,, yyy 20,, yy,,, yyy,, yy ,,, yyy,, yy,,, yyy,, yy,, yy 27,, yy,,, yyy,, yy,,, yyy,,, yyy 6,,, yyy,,, yyy,,,, yyyy,,, yyy,,,,,, yy yy yy

21 8 TIMING NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY 60N02509 Screw A Horizontal timing belt cover (GREY) A Horizontal tensioner roller cover (GREY) B Screw N0250 Screw A Vertical tensioner roller cover (GREY) 7 60N02505 Screw A Vertical timing belt cover (GREY) A Screw A Central cover timing side Elastic-stop ring nut Washer B Timing belt roller A Timing drive toothed belt A Belt roller separating washer Fixed tensioner assembly A Complete vertical cylinder tensioner roller Ring Bearing B Screw A Washer A Snap ring Woodruff key C Timing gears pair Hexagon nut Lock washer A Lay shaft Woodruff key 2

22 9 FILTERS AND OIL PUMP ,, yy yyy,,,,, yy,y

23 9 FILTERS AND OIL PUMP NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY A Complete oil pump A Pump cover A Pump driving gear Pump driven gear A Pump body A Screw B Woodruff key B Screw A Spring washer N0250 Screw A Spring washer A Pump drive gear A Bush A Bypass spring Locating bush A Gasket Oil drain plug with magnet A Gasket Oil filter Oil filter cartridge Nipple O-ring A Screw Snap ring Circlip Reduction bush A Cap Gasket A Bypass valve A Bypass spring A Bypass cap A Aluminium gasket A Screw 3 23

24 0 HALF CRANKCASES ,,, yyy ,,, yyy,,, yyy ,, yy,,, yyy,,, yyy ,,, yyy,,, yyy ,, yy,, yy,, yy,, yy 39,, yy, y

25 0 HALF CRANKCASES NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY B Complete half-crankcases pair Seal ring Needle bearing Snap ring Fluid sealant Stud bolt for fastening head 8 cylinder A Special washer Nut Bearing Screw Keep plate Bearing Seal ring A Spacer N0079 Screw Seal ring Bearing Circlip Gearbox pin bush A Bearing A Bearing holder bush A Seal ring Locating dowel B Screw Bearing A Special screw B Screw O-ring Bearing B Bearing holder bush B Screw A Bush A Breather valve Gasket Screw A Ring N0 Washer A Bush A Bush A Aluminium gasket A Screw A Nipple A Aluminium gasket 2 25

26 ALTERNATOR COVER ,y

27 ALTERNATOR COVER NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY B Generator A Bearing Circlip AB Chain cover B Screw N0250 Screw A Ignition inspection cap O-ring BB Cover C Screw Seal ring Gearbox pin bush B Screw B Screw Fluid sealant 6 60N02509 Screw N025 Screw Locating bush AB Generator cover A Bracket B Screw 2 27

28 2 ELECTRIC STARTER AND IGNITION ,, yy,,, yyy,,, yyy,,, yyy

29 2 ELECTRIC STARTER AND IGNITION NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY A Complete starter motor (8-9 included) N0 Spring washer A Nut A Starter motor gasket 5 60N0250 Screw A Starter motor sprocket Circlip Intermediate gear pin Washer A Intermediate gear assembly Circlip B Screw A Flange A Locating pin Check ring B Ignition flywheel Washer B Inner ring A Needle bearing A Electric starter driven gear Fairlead ring nut cap A Starter clutch Connector Coupling Plate N0 Washer N0 Spring washer N02463 Screw A Sensor Pick-up holder A Nut Washer A Stud bolt A Gasket A Fairlead ring nut Fairlead rubber ring A Screw 8 29

30 30 M HEAD: TIMING 3,,,,,,,,,,,,,,,, yy yyyy yyyy yyyy yy,,,, yy yy,,, yy y,,,,,,,,,,,,,,,, y yyy yyy yyyy yyy yy,,, y yy,,,, yy yy

31 3 HEAD : TIMING NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY Elastic-stop ring nut Washer A Timing belt roller A Belt roller separating washer A Vertical rubber cap A Belt roller spacer Seal ring Bearing Spacer N07335 Screw A Horizontal rubber cap Stud bolt Bearing Washer Woodruff key Horizontal head camshaft Shim th Shim th Cap gasket Bearing B Cap with bearing N02509 Screw Vertical head camshaft Stud bolt 4 3

32 4 VERTICAL HEAD 7 * Scodellino ritorno Return cap Coupelle retour Einstellhülse , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , ,6 0 9,,,,, 8 2 7, ,,, yyy ,,, yyy,, yy ,,,,,, yyyyyy,,,,,, yyyyyy,,,,,, yyyyyy,,,,,, yyyyyy,,,,,, yyyyyy,,,,,, yyyyyy,,,,,, yyyyyy LOCTITE 50 9 * Registro bilanciere Adjustment Réglage Ventilkäppchen , , , , , , , , A A A A , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , ,

33 4 VERTICAL HEAD NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY A Complete vertical head A Intake valve seat AB Oversize intake valve seat AC Oversize intake valve seat A Exhaust valve seat AB Oversize exhaust valve seat AC Oversize exhaust valve seat A Intake valve cast iron guide AB Oversize valve guide AC Oversize valve guide AD Oversize valve guide C Exhaust valve bronze guide CB Oversize valve guide CC Oversize valve guide CD Oversize valve guide A Valve seal A Closing rocker spring Shim th Shim th Shim th Shim th Shim th Shim th A Valve cover gasket AA Valve cover B Screw Shim Spring Opening rocker Rocker shaft Oversize rocker shaft Closing rocker See table A Split rings See table A Valve seal A Exhaust valve A Intake valve A Copper gasket A Screw 33

34 4 * , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , ,0 Scodellino ritorno Return cap Coupelle retour Einstellhülse HORIZONTAL HEAD , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , A A A A 0 LOCTITE ,,,,, yy,, yy,, yy, y ,,,,, 6 * , , , , , , , ,4 2 Registro bilanciere Adjustment Réglage Ventilkäppchen , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , ,

35 5 HORIZONTAL HEAD NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY B Complete horizontal head C Exhaust valve bronze guide CB Oversize valve guide CC Oversize valve guide CD Oversize valve guide A Intake valve cast iron guide AB Oversize valve guide AC Oversize valve guide AD Oversize valve guide A Exhaust valve seat AB Oversize exhaust valve seat AC Oversize exhaust valve seat A Intake valve seat AB Oversize intake valve seat AC Oversize intake valve seat A Intake valve A Exhaust valve Shim th Shim th Shim th Shim th Shim th Shim th A Closing rocker spring Rocker shaft Oversize rocker shaft A Valve cover gasket AA Valve cover B Screw See table A Split rings See table Opening rocker Closing rocker Spring Shim A Valve seal A Valve seal Vibration damper pad AA Valve cover Rubber cap A Copper gasket A Screw 35

36 TAVOLA TABLE BILD TABLA 6 INLET DICT

37 6 INLET DICT NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY Gasket B Intake manifold A Breather pipe A Breather pipe FN Nut A Clamp A Rubber hose AB Air box (GREY) Screw A Clamp A Fuel pipe AB Air box (GREY) A Filter Spring 37

38 TAVOLA TABLE BILD TABLA 7 FUEL INFEED

39 7 FUEL INFEED NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY A Clamp C Filter/fuel cock pipe A Clamp B Fuel cock A Clamp A Fuel cock/fuel pump pipe C Fuel chock/inlet duct pipe A Clamp A Pump/intake manifold pipe Union Aluminium gasket A Clamp A Tube 4 60N02509 Screw Nut Fuel pump Bush Rubber pad A Pin B Screw A Inner spring 39

40 TAVOLA TABLE BILD TABLA 7. STANDS

41 7. STANDS NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY A Side stand B Screw A Side stand A Screw A Switch A Spring A Outer spring B Plate C Pivot G Nut 4

42 TAVOLA TABLE BILD TABLA 8 CARBURETOR

43 8 CARBURETOR NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY B Chamber A Gasket A Holder A O-Ring A Gasket F Main jet A Starter jet D Idling jet A Filter A Gasket A O-ring A Washer A Spring A Adjusting screw A O-ring A Float A Cap D Carburetor A Cap A Heater 43

44 TAVOLA TABLE BILD TABLA 9 CARBURETOR

45 9 CARBURETOR NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY A Spring A Ring A O-ring M Taper needle A Ring A Washer A Diaphragm assembly A Needle valve A Gasket A Air jet A Jet A O-ring A Diaphragm assembly A Spring A Cover 2 45

46 TAVOLA TABLE BILD TABLA 20 4 ELECTRIC SYSTEM ,,, yyy,, yy,, yy,, yy 23,, yy ,,,,,, yyyyyy,,,,,,, yyyyyyy ,,, yyy,, yy

47 20 ELECTRIC SYSTEM NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY B Wiring B Spacer Rubber pad A Screw A Plate A Sticker schema fusibili A Case cover Fuse 7.5A Fuse 5A A Fuse 30A A Flashing device A Holder A Relay 4 60N025 Screw Washer A Clamp A Clamp A Clamp A Fuse 30A Nut A Battery branch cable A Terminal cap A Battery A Spring hook A Battery breather pipe A Ring A Terminal cap(black) A Battery-frame grounding cable Nut Clamp A Spacer C Regulator A Screw AB Horn (BLACK) A Retainer B Screw End section Connector B Solenoid starter-starter motor cable A Battery gasket A Holder A Solenoid starter branch cable A Spring washer A Nut A Remote switch Connector A Holder N0 Spring washer A Screw A Special screw N0 Spring washer A Frame-engine grounding cable A Screw 47

48 TAVOLA TABLE BILD TABLA 20 4 ELECTRIC SYSTEM ,,, yyy,, yy,, yy,, yy 23,, yy ,,,,,, yyyyyy,,,,,,, yyyyyyy ,,, yyy,, yy

49 20 ELECTRIC SYSTEM NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY N0 Washer A Cover Clamp A Fairlead 49

50 TAVOLA TABLE BILD TABLA 2 IGNITION SYSTEM

51 2 IGNITION SYSTEM NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY C Electric wiring Coupling Connector Ignition control unit A Bracket A Screw N0 Spring washer A Screw Coil Rubber pad A Spare cap A Spark plug 2 5

52 TAVOLA TABLE BILD TABLA 22 EXHAUST SYSTEM MARCA E CODICE MAKE AND CODE MARQUET ET CODE FABRIKAT UND CODE MARCA Y CODICE

53 22 EXHAUST SYSTEM NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY Exhaust gasket Half bushes AB Exhaust ring nut (GREY) Nut A Horizontal head exhaust pipe A Vertical head exhaust pipe A Cap A Clamp A Rubber pad Washer A Screw B R.H. silencer A R.H. bracket A Spacer Nut B L.H. silencer Screw Washer A L.H. bracket A Bush A Copper gasket A Spacer A Washer A Screw 53

54 TAVOLA TABLE BILD TABLA 23 INSTRUMENT PANEL A

55 23 INSTRUMENT PANEL NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY D Complete instrument panel (speedometer - miles) A Speedometer (miles) A Vibration damper pad A Gasket A Plate B Panel A Speedometer transmission C Electric wiring Warning lamp bulb2v-2.w Warning lamp bulb2v-.2w A Wrench A Screw A Rubber pad 4 60N5548 Washer A Nut A Cover A Knob A Screw A Spacer A Key-operated switch A Cover 22 60N5506 Washer A Special screw N02509 Screw N0 Spring washer A Connector holder A Sensor 55

56 TAVOLA TABLE BILD TABLA 24 FRONT HEAD-LIGHT

57 24 FRONT HEAD-LIGHT NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY C Complete headlight Bulb A Lamp holder A Cap A Electric wiring 6 60N02509 Screw A Headlight holder A R.H. bracket A Turn indicator A Cup Bulb 55/60W Rubber pad A Spacer A Fairlead Bulb 4W A Turn indicator A Nut N0 Screw A Retainer A L.H. bracket A Ring Fairlead rubber ring N0 Washer 24 60N0250 Screw 25 60N07335 Screw 2 57

58 TAVOLA TABLE BILD TABLA 25 PLATE HOLDER - REAR LIGHT

59 25 PLATE HOLDER - REAR LIGHT NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY A Number plate holder A Clamp A Tail lamp A Cup A Tail lamp A Cup Vibration damper pad Spacer A Nut A Turn indicator B Electric wiring FN Nut N5548 Washer A Turn indicator Bulb FN El-stop nut A Nut A Washer A Cat s eye B Plate A Screw A Two-light bulb 2V 5/2W Bulb N07335 Screw D Protection A Headlight holder B Screw A Plate A Holder A Cat s eye 2 59

60 TAVOLA TABLE BILD TABLA 26 FORK ,, yy,,, yyy,,, yyy 28 3,, yy,, yy,, yy

61 26 FORK NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY A L.H. fork leg assembly A Complete L.H. slider A R.H. fork leg assembly A Steering head A Screw 6 60N02557 Screw A Steering head base with pin A Special screw A Nut Ring nut C Cap A Washer N02558 Screw A Wheel spindle bush A Complete R.H. slider A Adjusting screw A Washer A Dust seal A Ring A Seal ring A Check ring A Stanchion tube A Nut A Spring seat retainer A Damper tube A Flexible collar A Centering ring A Spring A R.H. clamp A O-ring A Complete cap A Bush A Bush A Centering ring A L.H. Clamp A Cat s eye 2 6

62 TAVOLA TABLE BILD TABLA 27 FRONT AND REAR WHEELS

63 27 FRONT AND REAR WHEELS NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY A Front wheel rim A Valve A Inner spacer Bearing A Brake disc Relay drive ring B Screw A Front wheel spindle Speedometer transmission Seal ring A Snap ring B Nut A Rear wheel rim A Inner spacer A Brake disc A Rear wheel spindle Bearing A Vibration damper B Pin A Nut B Rear sprocket flange A Bush A Ring gear z= Bearing A Spacer B Fork nut A Final drive kit Valve A Chain (00 Links) A Cover 63

64 TAVOLA TABLE BILD TABLA 28 HALF HANDLEBARS ,, yy,y

65 28 HALF HANDLEBARS NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY A Clutch drive pump Spare inspection window Spare lever pin A Lever with dowel Spare cap D Clutch control pipe (METAL PLAITED) Spare bracket A Copper gasket A Special screw C L.H. rear-view mirror C Bracket B Screw C R.H. rear-view mirror A R.H. switch B Handlebar A Throttle control A Washer A Grips pair A Cap A Screw D Throttle closing cable D Throttle opening cable C Stud bolt A L.H. switch Bleed A Filler Cap A Starter control transmission 65

66 TAVOLA TABLE BILD TABLA 29 FRONT BRAKE ,, ,,,,,,,,,,, 66

67 29 FRONT BRAKE NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY A Front brake pump A Lever with dowel A Rubber pad Nut B Microswitch Spare lever pin A Dust seal A Screw Spare cap Spare inspection window Spare bracket A Copper gasket A Filler D Pump-shunt valve pipe A Spring A Spare pins and spring A Pads pair B L.H. brake caliper A Spare bleed union B Screw N0 Spring washer N0 Washer A Cover 67

68 TAVOLA TABLE BILD TABLA 30 REAR BRAKE , ,,, yyy,,, yyy, y

69 30 REAR BRAKE NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY A Special screw A Copper gasket E Rear brake line (METAL PLAITED) A Clamp A Pin A Spring AA Special screw A Rubber pad A Brake control lever A Nut 2 80A Spring Washer B Switch Bush 5 00A Fork A Tube AB Rear brake pump A Screw Adjuster rod A Rear brake caliper A Screw A Cap A Complete oil tank A Plate A Plate 26 60N02504 Screw B Screw N0 Spring washer Washer A Spare pins and spring A Dust seal Spare bleed union A Pads pair A Spare union A Dust cover 69

70 TAVOLA TABLE BILD TABLA 3 FRAME Dx 24 Sx

71 3 FRAME NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY AA Frame (GOLD) A Rubber pad Spacer A Fairlead A Nylon washer A Screw N0 Washer 8 80B Screw Special washer Bearing A Screw A Cap A Screw A Rod A Screw AA Front mudguard (RED) AB Front mudguard (BLACK) AC Front mudguard (YELLOW) AD Front mudguard (GREY) AE Front mudguard (BLUE) FF Nut A Cap A Screw Washer BA Sticker ( MONSTER 750) Insert SA R.H. body panel SA L.H. body panel A Locks kit A Rubber pad A Push rod N0 Spring washer A Washer 7

72 TAVOLA TABLE BILD TABLA 32 GEARCHANGE LEVER - FOOT REST

73 32 GEARCHANGE LEVER - FOOT REST NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY Vibration damper A Washer A Screw A Pin Ring Spring A R.H. foot-rest A R.H. foot peg holder plate A Ball A Plate A Washer Spring Screw A Nut Gearchange control lever Ball joint N0 El-stop nut A L.H. foot peg holder plate A Screw Washer A Spacer Bush Ball joint A L.H. nut A Screw 26 80A Pin A Gearchange lever A Rubber pad A L.H. foot-rest A Gearbox transmission rod 73

74 TAVOLA TABLE BILD TABLA 33 REAR FORK

75 33 REAR FORK NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY B Swingarm 2 60N02584 Screw A Shim th A Shim th A Swingarm pivot A Cap A Special screw N0 Washer A Clip B Special screw 2 0 8A Screw FN Nut A Clip A Plate B Screw A Washer B Sliding shoe B Cover A Screw A Screw Shim th A Plate A Rear mudguard AB Lower chain sliding shoe (GREY) A Snap ring N0 El-stop nut AB Upper chain sliding shoer (GREY) 75

76 TAVOLA TABLE BILD TABLA 34 REAR SUSPENSION

77 34 REAR SUSPENSION NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY 76300N0 El-stop nut A Shock absorber A Rocker assembly C Screw A Nut A Screw Needle bearing A Spacer Screw Shim A Bush BA Complete fork (GOLD) Ball joint A Ball joint A Spring seat A Ring nut A Ring nut A Spring 77

78 TAVOLA TABLE BILD TABLA 35 AIR INDUCTION - OIL VENT

79 35 AIR INDUCTION - OIL VENT NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY B Air filter box A Self-tapping screw A Upper half-case A Gasket B Lower half-case A Tube A Hook Spring pin A Screw A Spacer Rubber pad A Hose A Clamp A Clamp A Breather pipe Filter element A Screw A Oil breather tank A Breather pipe 20 60N02509 Screw 2 60N025 Screw A Air funnel A Filter case cover Plate 79

80 TAVOLA TABLE BILD TABLA 36 OIL COOLER

81 36 OIL COOLER NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY A Guide ring Fairlead rubber ring N0 Washer A Nipple N025 Screw A Vibration damper N02 Screw C Retainer A Oil cooler A Aluminium gasket B Oil delivery pipe B Oil return pipe 8

82 TAVOLA TABLE BILD TABLA 37 FUEL TANK A A

83 37 FUEL TANK NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY AA Fuel tank (RED) AB Fuel tank (BLACK) AC Fuel tank (YELLOW) AD Fuel tank (GREY) AE Fuel tank (BLUE) AA Sticker 2 (RED,BLUE,BLACK) AB Sticker (GREY,YELLOW) A Rubber pad A Panel A Hook Screw A Tank cap E Screw A Gasket A.033.A Fuel tank (unpainted) Split pin 2 80C Shim A Bush B Pin A Clamp A Union/filter pipe A Union A Copper gasket A Clamp A Screw A Fuel filter A Breather pipe A Gasket A Fuel level gauge A Plate A Copper gasket Screw A Screw B Screw 83

84 TAVOLA TABLE BILD TABLA 38 SEAT

85 38 SEAT NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY BA Red cover BB Black cover BC Yellow cover BD Silver cover BG Blue cover A Cover for pillion rider seat (unpainted) A Helmet anti-theft wire A Gasket A Threaded insert A L.H. plate A Seat padding A Cover A Special screw A Screw N0 Washer N0 Spring washer A Pin 3 60N02482 Screw B Tool bag A R.H. plate Nylon washer A Flexible cable B Screw A Seat lock A Mudflap Nut Washer A Owner s manual N0 Spring washer N0077 Screw A Plate A Rubber pad 85

86 TAVOLA TABLE BILD TABLA 39 FUEL INFEED

87 39 FUEL INFEED NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY A Screw Rubber pad Vibration damper pad A Bracket A Tube A Plate A Spacer Nut B CANISTER filter A Clamp A Clamp A Tube A Clamp A Tube A Clamp Idling jet A Spring B Clamp Union Aluminium gasket A Tube A Spring Shunt valve A Tube 87

88 TAVOLA TABLE BILD TABLA 40 MARKING PLATES OBJECTS IN MIRROR ARE CLOSER THAN THEY APPEAR Cod.43366A 2 CAUTION NEVER FILL TANK SO FUEL LEVEL RISES INTO FILLER NECK. IF TANK IS OVERFILLED, HEAT MAY CAUSE FUEL TO EXPAND AND FLOW INTO EVAPORATIVE EMISSION CONTROL SYSTEM RESULTING IN HARD STARTING AND ENGINE HESITATIO Cod.43364A 3 HELMET HOLDER UNDER THE SEAT 88

89 40 MARKING PLATES NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY NOTES NO. CODE NO. DESCRIPTION VALIDITY Q.TY A Sticker A Label A Sticker 89

90 PAINTS Paint Code LECHLER Code SALCHI Code PPG B C D "Rosso Anniversary " A "Grigio metallizzato " "Nero metallizzato " "Giallo "Blu metallizzato " A B C D Front fender Headlight fairing Fuel tank Tailseat cover CATALOGUE No. : C CATALOGUE No. : C

91 INDEX A A A A

92 INDEX B