Section Contents. Product Reference Guide Numbering System / How To Order & 16. Selection Procedure... 17

Transcription

1 Section ontents roduct Reference uide... - umbering System / ow To Order... 4 & 6 Selection rocedure ssemblies and ounting ositions Recommended Lubricants... 0 R Selection Tables RTO & TY Selection Tables RR imensions STLSS ashdown uty ccessories /8

2 700 Series orm ear roduct Reference uide Single Reduction langed Reducers & on-langed Reducers Ordering nformation age 4- Selection/Rating nformation ages 7, - Lubrication age 0 otor Selection ages 9 & S imensions age 4 Q700 S imensions age 4 /Q700 imensions age /Q700R imensions age 7 /Q700/ imensions age 8 /Q/S700 imensions age /Q-R/L + S700V/ imensions age S imensions age /8

3 700 Series orm ear Speed Reducers 700 imensions age imensions age / imensions age 47 /S700 imensions ages R/L imensions age 0 S700V/ imensions age SS700 imensions age 9 SS700 imensions age 9 SS700V/ imensions age 60 SS700 imensions age 6 SS700 imensions age 6 SSS imensions age /8

4 700 Series Single Reduction 700 Series Right ngle orm earbox - Single Reduction S Q Z T Shaft Style lank Solid Shaft ostount ollow (setscrews both sides, bore size selectable) S ollow (setscrews one side, bore size fixed) Reducer aterial/aint lank ast ron, Std. ray paint ast ron, hite ostleen paint S ast ron, Stainless ostleen paint SS Stainless Steel material no paint nput Shaft Style lank Solid rojecting nput Shaft - Quill Style otor lange R oupling Style otor lange Q Quick onnect otor lange (close coupled) Series xact ear Ratio Ratio to enter istance (inches) ase/ounting ttachment* lank o ase orizontal base Top ount orizontal base ottom ount R Riser lock Top ount Vertical igh base Right ount Vertical Low base Right ount Vertical igh base Left ount Vertical Low base Left ount R ostount racket Right ount L ostount racket Left ount onveyor lange dptr Right ount onveyor lange dptr Left ount V ollow lange Right ount ollow lange Left ount X Vertical ase Rear ount Y Vertical ase ront ount *rojection of ase/lange/racket assumes one is always looking into the input shaft in the # mounting position Or onsult actory for vailability Lubrication lank o lubrication lubersynth S obil S 64 X obil 600 Vent lank Standard Vent ressure Vent ( psi) Z osivent (sealed) ndcap or an (7-760 only) ndcap (standard) an Oil Seal lank Standard Seal T Two Standard nput Seals igh pressure washdown output seals and double input seals (stainless products only) otor ounting OR T O OT OR YY 4 4Z.00 /8 x /6 6.6 /6 x / 40T/80.87 /6 x / 80T/0. /4 x /8 0T/0.7 /6 x / 0T.6 /8 x /6 lank Solid nput Shaft (o lange) /8

5 700 Series Single Reduction lutch/rake otor S 4 40TR-6 T- ostount ore ode or Series Only Specified in /6" increments. xample: /4 = 0 /8 0 /4 7/8 4 /6 6 -/6 7 -/8 8 -/6 9 -/4 0 -/6 -/8-7/6 -/ 4 -/8 6 -/6 7 -/4 8-7/8 0 -/6 -/8 4 -/6 -/4 6-7/6 9-7/6 See catalog page 8 for availability by center distance. onsult actory for etric ores ommon -ace rakes nstalled /0 V 60hz t-lb ore ode 6R- 6R TR /460 V 60hz t-lb ore ode T-6 6 Other sizes available. See catalog page 4. Rating otor onduit box Orientation (hen looking at fan end of motor and gearbox is in mounting position #) 0 O clock O clock(standard for & shaft assemblies) 6 6 O clock 9 9 O clock (standard for shaft assemblies) ommon -ace otors nstalled ore ode Voltage / / /4 RT T / RT T / RT T T-SS T- T ounting ositions /4 RT T-SS T- lank - o Lubrication Supplied T/8 or actory relubrication ndicate ounting osition Standard ounting (orm over) -6 Refer to ounting ositions in atalog pages 8-9 RT-/8 T/8-SS T/8- T T-SS T- Shaft (hen facing nput and worm on top). T T-SS T S - S - S - arbon Steel rojection Left arbon Steel ouble rojection arbon Steel rojection Right Stainless rojection Left Stainless ouble rojection Stainless rojection Right /8 -SS - LT LT-SS LT- T Other motors available, please see catalog pages to 4. T T SS Totally enclosed non-ventilated Totally enclosed fan cooled Stainless nverter uty (0: turn down constant torque) 6 40T 80T -48-7/8

6 Single Reduction umbering System / ow to Order Style ase Ratio Lubrication an Vent esignates reducer or flanged reducer, projecting or Style hollow output shaft. esignates cast iron flange and base. (Standard on motor flanges (80T) and up and all bases except horizontal (70-76). lank Single reduction reducer with projecting input and output shafts. (o code letter required). Single reduction reducer with projecting input and ostount hollow output shaft. (o flange) ( 7-78) S Single reduction reducer with hollow output shaft. (s 78, 7, 76 and 7). Single reduction flanged reducer (Quill types) with projecting output shaft. Single reduction flanged reducer (Quill types) with ostount hollow output shaft. (s 7-78) S Single reduction flanged reducer (Quill types) with hollow output shaft. (s 78, 7, 76 and 7) Q Single reduction flanged reducer (oupling types) with projecting output shaft. Q Single reduction flanged reducer (oupling types) with ostount hollow output shaft. (s 7-78) R Single reduction flanged reducer (oupling types) with rojecting output shaft Only esignates ast ron, hite ostleen paint S esignates ast ron, Stainless ostleen paint SS Stainless Steel Single reduction flanged reducer (Quill types) with projecting output shaft. SS Stainless steel single reduction flanged reducer with ostount hollow output shaft. enter distance, rounded off , ase ase positions relative to output shaft. Shipped separately as ase s. See age 9. lank o base kit supplied, orizontal bases,, & - Vertical ases* R/L ostount racket X nput Vertical p Y nput Vertical own R orizontal base with riser block V, langed bases, available on S hollow shaft models only. actory assembled. / langed bases, available on hollow shaft models only. *or, vertical base arrangements, see ages 8, 9. Ratio See Selection Tables for available ratios Lubrication Optional relubrication.* lank - o Lubrication supplied. lubersynth S obil S64 Synthetic Lubricant X obil 600 *hen specifying optional prelubrication, include mounting position after shaft assembly. an Optional fan available on sizes single reduction only. Shipped separately as an. See age 0. lank - o an. - nd ap (standard) - an Oil Seals Vent ressure Relief. lank Standard Vent S Vent Z osivent ressure ompensationg ladder Oil Seals lank Standard Seal T ouble nput Seals. Recommended for mounting positions,, 4, 6 - igh pressure/wash down configuration for stainless gearboxes. ontains double input seals and axial face seals on the output. ounting ore ode esignates flange size and input bore diameter. langed reducers only. Leave blank for projecting input reducers. ounting nput ore eyway 4 4Z.00 /8 x /6 6.6 /6 x / 40T/80.87 /6 x / 80T/0. /4 x /8 0T/0.7 /6 x / 0T.6 /8 x /6 See page 98 for ounting imensions. Shaft ssembly ssembly shaft arrangements. See assemblies, pages 8 and 9. Standard assembly (left) ouble output shaft projection Opposite to standard (right) S Stainless standard assembly (left) S Stainless double output shaft projection S Stainless opposite to standard (right) ounting osition esignates the position of oil and vent plugs with respect to mounting. lank or units not supplied prelubricated. -6 See pages 8 and 9. ore ode ounting Shaft ssembly ounting osition Specified in /6 increments. See page 8 for complete offering. xample /4 = 0 or Series only. ow to Order hen ordering reducers please include code letters for Style,, ase (if required), Ratio, an (if required), Lubrication (if required), ounting (if flanged reducer), Shaft ssembly and otor (if required). XL: Required size, 7 Quill types flanged reducer, 0: ratio, /8 input bore, standard assembly, with horizontal base, no lubrication. otor to be /4, 70 R, 0/460 Volt, hase, 60 cycle, open dripproof Reducer, ase and otor Shipped separately: ORR: Reducer ase otor -. Reducer, ase and otor assembled: ORR: ore ode /8

7 Single Reduction Speed Reducer Selection rocedure To properly select a speed reducer, the following application information must be known: nput R (Ratio) nput orsepower Service actor on-otorized Speed Reducer. etermine service factor from table below.. etermine design horsepower. esign orsepower = pplication Load x Service actor. Select a speed reducer size that satisfies output R, service class and/or output torque requirements. 4. heck overhung load capacity. otorized Speed Reducer. etermine service class from table below.. Select a reducer size that satisfies output R, service class and/or output torque requirements.. heck overhung load capacity. Service actor Table lass of Service Service actor Operating onditions Overhung Load f the output shaft of a speed reducer is connected to the driven machine by other than a flexible coupling, an overhung load is imposed on the shaft. This load may be calculated as follows: OL = T OL = Overhung Load (L.) T = Shaft (L..) = of Sprocket, inion or ulley (.) = Load onnection actor Load onnection actor Sprocket or Timing elt inion and ear rive.... ulley and V-elt rive ulley and lat elt rive....0 n overhung load greater than permissible load value may be reduced to an acceptable value by the use of a sprocket, pinion or pulley of a larger. Relocation of the load closer to the center of reducer will also increase OL capacity. ermissible Overhung Loads and Shaft Thrust Loads are listed for each reducer in the Tables on pages oderate Shock-not more than minutes in hours. niform Load-not more than 0 hours per day. oderate Shock-not more than 0 hours per day. niform Load-more than 0 hours per day. eavy Shock-not more than minutes in hours. oderate Shock-more than 0 hours per day. aximum nput Speeds 70, R 7 through R 78, 7 00 R R.7 eavy Shock-not more than 0 hours per day..00 eavy Shock-more than 0 hours per day. or complete Service actors and Load lassifications, see ngineering Section, ages 48 and 49. Single Reduction Selection Tables apacity Selection Tables on pages -9 list catalog numbers and ratios of both reducers and gearmotors. R, output torque and horsepower are all based on 70 R input. torque and horsepower capacities at other input R s are listed on pages 0-. or motorized reducer selection, select the desired output R and refer to the gearmotor ratings column. or non-motorized reducers, refer to the reducer gear capacity columns. or the desired, torque and service factor that satisfies your requirements, a 700 Series basic reducer number will be indicated. or complete catalog numbering system, descriptions and options, refer to ages 4-. OT: orsepower ratings for 70 R should not be exceeded when operating at higher input speeds. Ratings shown reflect maximum gear capacity with lubersynth lubricant. The use of other lubricants may reduce ratings by up to %. Ratings are mechanical not thermal /8 7

8 langed Reducer ssemblies and ounting ositions ssemblies - /Q/R 700 Series Standard assemblies define output shaft (slow speed) projection with respect to input shaft (high speed) and mounting surface. Types and are horizontal bases. S T * Types and are vertical high bases and Types and are vertical low bases. Types X is input vertical up. asic models and separate base kits are supplied unless otherwise specified. ssembly is available at a slight additional charge. See ages 4- for complete ordering instructions. TY TY * * nput may rotate clockwise or counter clockwise. TY & OR OTR ORTOS OT SO, OTT TORY. TY & * * TY X * * Standard assemblies ounting ositions - /Q/R - S - /Q 700 Series Standard assemblies are for osition. The design permits any types of assembly to be mounted in any position shown by the proper location of the vented oil filler, level and drain plugs, at the time of installation. or other than osition, order standard and relocate vented oil filler, level and drain plugs. or production orders oston ear will assemble units for the specified mounting position desired at no additional charge. OTOR ORZOTL 4 LOOR OTOR ORZOTL LOOR LOOR LOOR OTOR VRTL TO hen ordering speed reducers pre-lubricated, the ounting osition must be indicated to ensure proper oil level and seal configuration. LOOR 6 ndicates proper oil level. hen mounting gearboxes in positions,, 4, 6 ouble nput Seals are required /8

9 on-langed Reducer ssemblies and ounting ositions ssemblies Series Standard assemblies define output shaft (slow speed) projection with respect to input shaft (high speed) projection and mounting surface. Types and are horizontal bases. Types and are vertical high bases and Types and are vertical low bases. Type X is input vertical up. Type Y is input vertical down. asic models and separate base kits are supplied unless otherwise specified. ssembly is available at a slight additional charge. See ages 4- for complete ordering instructions. nput may rotate clockwise or counter clockwise. rrows indicate relative rotation. OR OTR ORTOS OT SO, OTT TORY. * Standard assemblies TYL OT OSTOS (xamples shown for single-reduction models only) ORZOTL T ST LOOR 4 LOOR VRTL T ST LOOR 6 ounting ositions S Series Standard assemblies are for osition. The design permits any types of assembly to be mounted in any position shown by the proper location of the vented oil filler, level and drain plugs, at the time of installation. or other than osition, order standard and relocate vented oil filler, level and drain plugs. or production orders oston ear will assemble units for the specified mounting position desired at no additional charge. LOOR LOOR ndicates proper oil level. hen mounting gearboxes in positions,, 4, 6 ouble nput Seals are required. xample: 7-T--6 LOOR TO hen ordering speed reducers pre-lubricated, the ounting osition must be indicated to ensure proper oil level and seal configuration /8 9

10 Recommended Lubricants & apacities The following table indicates the types and viscosity of lubricants suitable for reducers operating at various temperatures. Lubrication and maintenance instructions are provided with each speed reducer. These instructions should be followed for best results. t is important that the correct types of oil be used since many oils are not suitable for the lubrication of gears. Various types of gearing require different types of lubricants. The lubricant must remain free from oxidation and contamination by water or debris, since only a very thin film of oil stands between efficient operation and failure. To assure long service life, the reducer should be periodically drained (preferably while warm) and refilled to the proper level with a recommended gear oil. nder normal environmental conditions oil changes are suggested after the initial 0 hours of operation and thereafter at regular intervals of 00 hours or every 6 months. Synthetic lubricants will allow extended lubrication intervals due to its increased resistance to thermal and oxidation degradation. t is suggested that the initial oil change be made at 00 hours and, thereafter, at 000 hour intervals. uring the initial period of operation, higher than normal operating temperatures may be seen. This is due to the initial break-in of the gear set. The temperature of Single Reduction orm ear Reducers may reach approximately. nclosed orm ear Reducers mbient (Room) Temperature 0 to ** ( 9 to 07 ) 0 to ( 4 to 07 ) Recommended Oil (or equivalent) lubersynth* Synthetic obil S64 Synthetic Viscosity Range 00 Oil Type SO Viscosity rade o.+ 90/ /00 O 0/460 orm ear Lubricant vailable rom oston ear Type lubersynth obil S64 Qt. Qt. tem ode vailable in quarts only TO: Relubricate more frequently if drive is operated in high ambient temperatures or unusually contaminated atmosphere. igh loads and operating temperatures will also require the use of frequent lubrication. * Synthetic recommendation is lubersynth 6-460, other lubrications may reduce efficiency and torque capacity. + Other lubricants corresponding to /SO numbers are available from all major oil companies. See age 4 for lubricant interchange. ** The lubersynth lubricant will perform at temperatures considerably higher than. owever, the factory should always be consulted prior to operating at higher temperatures, as damage may occur to oil seals and other components. R: ifferent oil types should not be mixed. or example lubersynth is not compatible with obil S64. OR SL RTO OLY: RR TO LRTO STLLTO STRTOS. Oil Levels for Typical ounting ositions (xamples shown for single-reduction models only) ORZOTL T ST LOOR LOOR ndicates proper oil level. 4 LOOR LOOR VRTL T ST LOOR LOOR 6 Oil capacity in fluid ounces for cast iron units* nit ositions 4 & *See page 6 for stainless steel units. hen mounting gearboxes in positions,, 4, 6 ouble nput Seals are required /8

11 ngineering ata Quick Reference odel Selection hart Reducer Ratio R lass Service Single Reduction (.0 Service actor) nput 70 rpm /6 /4 / / /4 -/ 7-/ OT: This chart is meant only as a guide. or actual ratings, see ages 0-. Reducer Ratio R lass Service Single Reduction (. Service actor) nput 70 rpm /6 /4 / / /4 -/ 7-/ OT: This chart is meant only as a guide. or actual ratings, see ages 0-. Reducer Ratio R lass Service Single Reduction (.7 Service actor) nput 70 rpm /6 /4 / / /4 -/ 7-/ OT: This chart is meant only as a guide. or actual ratings, see ages /8

12 700 Series Single Reduction R & apacity Selection 70 R nput R Ratio 0 (lb.in.) or Ratings at Other Speeds, See Tables on ages 0- on-langed Reducers ear apacity nput fficiency otor Ratings (lb.in.) langed Reducers (earmotor) Service lass l ll l l Q vailable Styles S Q R SS ore ode otors* 0/460 V hase 60 z T T T T T T T T-/8 T T T T-/8 T T T-/8 T T LT T LT T LT T T T T T T T T T-/8 T T T T-/8 T T T-/8 LT T LT T * Totally nclosed, an ooled. or complete motor atalog umbers and additional motors, see ages 7 and 4. Shaded areas denote which styles are available for a given center distance and ratio. See ages 4- for style descriptions. 7 & 760 SZS VLL OLY R-L OL TYS. RTS SO RLT T S O LRSYT /8

13 R 700 Series Single Reduction R & apacity Selection Tables Ratio (lb.in.) on-langed Reducers ear apacity nput fficiency or Ratings at Other Speeds, See Tables on ages 0- otor Ratings (lb.in.) langed Reducers (earmotor) Service lass Q vailable Styles S Q 70 R nput SS ore ode otors* 0/460 V hase 60 z T LT T LT T LT T T LT T T LT RT T ST ST RT T ST RT T ST RT T T T T-/8 T T T T T T T T T T T T-/8 T T T T T * Totally nclosed, an ooled. or complete motor atalog umbers and additional motors, see ages 7 and 4. Shaded areas denote which styles are available for a given center distance and ratio. See ages 4- for style descriptions. 7 & 760 SZS VLL OLY R-L OL TYS. RTS SO RLT T S O LRSYT /8

14 700 Series Single Reduction R & apacity Selection 70 R nput or Ratings at Other Speeds, See Tables on ages 0- R Ratio (lb.in.) on-langed Reducers ear apacity nput fficiency otor. Ratings (lb.in.) langed Reducers (earmotor) Service lass Q vailable Styles S Q R SS ore ode otors* 0/460 V hase 60 z T T LT T LT LT T LT l T LT T T LT T T T RT T T RT T ST RT T ll 4 4 T T T T T T T T T T T-/8 T T T-/8 T T T-/8 * Totally nclosed, an ooled. or complete motor atalog umbers and additional motors, see ages 7 and 4. Shaded areas denote which styles are available for a given center distance and ratio. See ages 4- for style descriptions. 7 & 760 SZS VLL OLY R-L OL TYS. RTS SO RLT T S O LRSYT /8

15 700 Series Single Reduction R & apacity Selection Tables R Ratio (lb.in.) or Ratings at Other Speeds, See Tables on ages 0- on-langed Reducers ear apacity nput fficiency otor Ratings (lb.in.) langed Reducers (earmotor) Service lass Q vailable Styles S 70 R nput R SS ore ode otors* 0/460 V hase 60 z T T-/8 LT T LT LT T LT T LT T T T T T T T T RT T T T T T T T T T T T-/8 T T T T-/8 T T T-/8 T * Totally nclosed, an ooled. or complete motor atalog umbers and additional motors, see ages 7 and 4. Shaded areas denote which styles are available for a given center distance and ratio. See ages 4- for style descriptions. 7 & 760 SZS VLL OLY R-L OL TYS. RTS SO RLT T S O LRSYT /8

16 700 Series Single Reduction R & apacity Selection 70 R nput or Ratings at Other Speeds, See Tables on ages 0- R Ratio 70 (lb.in.) on-langed Reducers ear apacity nput fficiency otor. Ratings (lb.in.) langed Reducers (earmotor) Service lass Q vailable Styles S Q R SS ore ode otors* 0/460 V hase 60 z LT T LT T T l T T T T T T T T T T-/8 T T T-/8 T T T-/8 T T T-/ T LT T LT LT T T T T T T T T T T T * Totally nclosed, an ooled. or complete motor atalog umbers and additional motors, see ages 7 and 4. Shaded areas denote which styles are available for a given center distance and ratio. See ages 4- for style descriptions. 7 & 760 SZS VLL OLY R-L OL TYS. RTS SO RLT T S O LRSYT /8

17 700 Series Single Reduction R & apacity Selection Tables R Ratio (lb.in.) or Ratings at Other Speeds, See Tables on ages 0- on-langed Reducers ear apacity nput fficiency otor Ratings (lb.in.) langed Reducers (earmotor) Service lass Q vailable Styles S 70 R nput R SS ore ode 4 otors* 0/460 V hase 60 z T T T T T T T T T T T T-/8 T T T-/8 T T T-/8 T T T-/8 T T LT T LT T LT T T T T T T T T T T T T T T T * Totally nclosed, an ooled. or complete motor atalog umbers and additional motors, see ages 7 and 4. Shaded areas denote which styles are available for a given center distance and ratio. See ages 4- for style descriptions. 7 & 760 SZS VLL OLY R-L OL TYS. RTS SO RLT T S O LRSYT /8 7

18 700 Series Single Reduction R & apacity Selection 70 R nput or Ratings at Other Speeds, See Tables on ages 0- R Ratio (lb.in.) on-langed Reducers ear apacity nput fficiency otor Ratings (lb.in.) langed Reducers (earmotor) Service lass Q vailable Styles S Q R SS ore ode LT otors* 0/460 V hase 60 z T T T T-/8 T T T T-/8 T T T-/8 T T T T T T T LT T LT T T LT T T T T T T T T T T T T T T T T * Totally nclosed, an ooled. or complete motor atalog umbers and additional motors, see ages 7 and 4. Shaded areas denote which styles are available for a given center distance and ratio. See ages 4- for style descriptions. 7 & 760 SZS VLL OLY R-L OL TYS. RTS SO RLT T S O LRSYT /8

19 700 Series Single Reduction R & apacity Selection Tables or Ratings at Other Speeds, See Tables on ages 70 R nput R Ratio (lb.in.) on-langed Reducers ear apacity nput fficiency otor Ratings (lb.in.) langed Reducers (earmotor) Service lass Q vailable Styles S Q R SS ore ode LT otors* 0/460 V hase 60 z T-/8 T T T T T T T T T T T LT T LT T T T T T T T T T T-/8 T T T T T T T T T T T T * Totally nclosed, an ooled. or complete motor atalog umbers and additional motors, see ages 7 and 4. Shaded areas denote which styles are available for a given center distance and ratio. See ages 4- for style descriptions. 7 & 760 SZS VLL OLY R-L OL TYS. RTS SO RLT T S O LRSYT /8 9

20 700 Series Single Reduction Ratio & apacity Selection Tables orsepower and apacities at Listed R nputs (Service actor.0) Ratio Series nput R R nput (lb-in) nput (lb-in) nput (lb-in) nput (lb-in) Overhung Load* 0 LS. 00 LS. 00 LS. 00 LS. Shaft Thrust Load 00 LS. 00 LS. 400 LS. 00 LS. RTS SO RLT X R TY T LRSYT *Overhung Load is at centerline of output shaft projection and with O TRST Load. ote: or input speeds above 70 R. o OT exceed 70 R input horsepower (See page 47) /8

21 700 Series Single Reduction Ratio & apacity Selection Tables orsepower and apacities at Listed R nputs (Service actor.0) Ratio Series nput R R nput (lb-in) nput (lb-in) nput (lb-in) nput (lb-in) Overhung Load* 700 LS. 900 LS. 000 LS. 0 LS. Shaft Thrust Load 700 LS. 800 LS. 900 LS. 000 LS. RTS SO RLT X R TY T LRSYT *Overhung Load is at centerline of output shaft projection and with O TRST Load. ote: or input speeds above 70 R. o OT exceed 70 R input horsepower (See page 47) /8

22 700 Series Single Reduction Ratio & apacity Selection Tables orsepower and apacities at Listed R nputs (Service actor.0) Ratio Series nput R R nput (lb-in) nput (lb-in) nput (lb-in) nput (lb-in) Overhung Load* 00 LS. 00 LS 000 LS. 000 LS. Shaft Thrust Load 00 LS. 00 LS. 00 LS. 00 LS. RTS SO RLT X R TY T LRSYT *Overhung Load is at centerline of output shaft projection and with O TRST Load. ote: or input speeds above 70 R. o OT exceed 70 R input horsepower (See page 47) /8

23 700 Series Single Reduction Ratio & apacity Selection Tables orsepower and apacities at Listed R nputs (Service actor.0) Ratio Series nput R R nput (lb-in) nput (lb-in) nput (lb-in) nput (lb-in) Overhung Load* 00 LS. 00 LS 400 LS. 400 LS. Shaft Thrust Load 900 LS. 900 LS. 00 LS. 00 LS. RTS SO RLT X R TY T LRSYT *Overhung Load is at centerline of output shaft projection and with O TRST Load. ote: or input speeds above 70 R. o OT exceed 70 R input horsepower (See page 47) /8

24 700 Series Single Reduction langed Reducer imensions 700/Q700 Series langed Quill/langed oupling Types asic odels (o ase) OR ORR ORTO, see age 6 OR RT ORTO, See ages 7, - SSLY TYS* STR R OTT Y (8) T. OLS L.... LL SOS S V 6 40T - ounting 700 Q700 R700 80T T 80T 0T 0T 6 80T 0T 0T 7 TR 760 /8-4 x 7/8 T OL L R- ounting T Low Speed Shaft prox. 80T eight (LS.) -ey 6 0T T Z 40T 0T epth -.00 V Sq. Lenght 700 Q / /8 / / / / / / / / /4 -/ / /4 -/ / /4 -/ / /4 -/ / /6-7/ / /8 -/ / / -/ / / -/ * See ssemblies and ounting ositions, age 8. ** or an s, see age 0. or ase s, see age 9. 4Z lange imensions: 700 =.6 : Q700 = 4. : R700 = 4.76 an o.** /8

25 700 Series Single Reduction langed Reducer imensions 700/Q700 Series langed Quill/langed oupling Types osition orizontal ase OR ORR ORTO, see age 6 OR RT ORTO, See ages 7, - R V OTT Y SSLY TYS* STR.. (4) T. OLS LL SOS S T - ounting 700 Q700 R700 80T T 80T 0T 0T 6 80T 0T 0T Z R- ounting 6 40T 80T 0T 0T T V Low Speed Shaft prox. eight (LS.) /.00.9 /8 / /.6.00 / / / / / / /4 -/ /..8 /4 -/ /..6 /4 -/ /.0. /4 -/ /.7. /6-7/ /.6.0 /8 -/ / / -/ / / -/ * See ssemblies and ounting ositions, age 8. ** or an s, see age 0. or ase s, see age 9. 4Z lange imensions: 700 =.6 : Q700 = 4. : R700 = 4.76 Sq. -ey Length 700 Q700 ase o. an o.** -48-7/8

26 700 Series Single Reduction langed Reducer imensions 700/Q700 Series langed Quill/langed oupling Types osition orizontal ase OR ORR ORTO, see age 6 OR RT ORTO, See ages 7, - SSLY TYS* * STR OTT Y R V.. ounting ll SOS S nput ore eyway 4Z 0. /8 x / /6 x / 40T 0.87 /6 x / 80T. /4 x /8 0T.7 /6 x / (4) T. OLS ll SOS S T - ounting 700 Q700 R700 80T T 80T 0T 0T 6 80T 0T 0T R Low Speed Shaft ounting T -ey 4Z 6 40T 80T 0T oles +.000/-.00 V Sq. Length prox. ieght (LS.) /.00.9 /8 / /.6.00 / / / / / / /4 -/ /..7 /4 -/ /..6 /4 -/ /.0. /4 -/ /.7. /6-7/ /.6.0 /8 -/ * See ssemblies and ounting ositions, age 8. ** or an s, see age 0. or ase s, see age 9. 4Z lange imensions: 700 =.6 : Q700 = 4. : R700 = Q700 ase o. an o.** /8

27 700 Series Single Reduction langed Reducer imensions 700/Q700 Series langed Quill/langed oupling Types R osition orizontal ase with Riser lock OR ORR ORTO, see age 6 OR RT ORTO, See ages 7, - (4) T OLS SSLY TYS* R OTT Y STR S.. V.. - ounting ounting 700 Q700 R700 4Z 6 80T 40T T 40T T 40T T 0T 0T 4Z 6 40T ounting 4Z 6 40T 80T 0 R Low Speed Shaft prox. ounting -ey eight 6 80T (LS.) 4Z 40T 0 S T -.00 V Sq. Length Q /.00.9 /8 / /.6.00 / / / / / / /4 / /..8 /4 / /..6 /4 / /.0. /4 -/ /.7. /6 7/ * See ssemblies and ounting ositions, age 8. ** or an s, see age 0. or ase s, see age 9. 4Z lange imensions: 700 =.6 : Q700 = 4. : R700 = 4.76 ase o. 80T 0 an o.** -48-7/8 7

28 700 Series Single Reduction langed Reducer imensions 700/Q700 Series langed Quill/langed oupling Types / osition Vertical ase; / igh ase; / Low ase OR ORR ORTO, see age 6 OR RT ORTO, See ages 7, - / SS SSLY TYS* ST R / SS ST R R.. ll SOS S.. (4) T. OLS OTT Y /8 V 6 40T - ounting 700 Q700 R700 80T T 80T 0T 0T 6 80T 0T 0T R Low Speed Shaft igh ase Low ase ounting -Y 80T pprox. ase pprox. 6 0T T eight (LS.) eight (LS.) 4Z 40T 0T oles -.00 V Sq. Length Q o. Q /.00.9 /8 / /.6.00 / / / / / / /4 -/ /..8 /4 -/ /..6 /4 -/ /.0. /4 -/ /.7. /6-7/ /.6.0 /8 -/ / / -/ / / -/ * See ssemblies and ounting ositions, age 8. ** or an s, see age 0. or ase s, see age 9. 4Z lange imensions: 700 =.6 : Q700 = 4. : R700 = 4.76 ase o. an o.**

29 700 Series Single Reduction langed Reducer imensions 700/Q700 Series langed Quill/langed oupling Types X osition Vertical ase; X = nput Vertical p OR ORR ORTO, see age 6 OR RT ORTO, See ages 7, - R.. OTT Y SSLY TYS* STR V (4) T. OLS ll SOS S T - ounting 700 Q700 R700 80T T 80T 0T 6 80T 0T 0T R- ounting 6 40T 80T T oles V Low Speed Shaft -ey proximate eight (LS.) Sq. Length Q /.6.00 / / / / / / /4 -/ /..8 /4 -/ /..6 /4 -/ * ssemblies define output (slow speed) shaft projection with respect to input (high speed) shaft and mounted surfaces. nput may be rotated clockwise or counterclockwise. See ssemblies and ounting ositions, age 8. or ase s, see age 9. 4Z lange imensions: 700 =.6 : Q700 = 4. : R700 = 4.76 ase o /8 9

30 700 Series Single Reduction langed Reducer imensions 700/Q700 Series langed Quill/langed oupling Types asic odels (o ase); ored to, ollow Shaft OR ORR ORTO, see age 6 OR RT ORTO, See ages 7, - OTT Y () SOT STSRS 0 RT (8) T T SSLY TYS* (OT SS) OLS R.. S.. V LL SOS S /8 6 40T 8-4 X T OL 7, 78 & 7 SZS OLY - ounting 700 Q700 R700 80T T 80T 0T 0T 6 80T 0T 0T L L # # # / / / / / / / R- ounting 6 40T 80T 0 S Tap T Low Speed Shaft pprox. ax -ey eight(ls.) epth +.00/ V Length Q / / / / See age / or / ey nformation / / / / * See ssemblies and ounting ositions, age 8. ** or an s, see age 0. See age 8 for available bore sizes. nput may be rotated clockwise or counterclockwise. The S style is recommended for direct replacement only. 4Z lange imensions: 700 =.6 : Q700 = 4. : R700 = 4.76 an o.**

31 700 Series Single Reduction langed Reducer imensions 700/Q700 Series langed Quill/langed oupling Types R/L osition ounting racket; ored to, ollow Shaft OR ORR ORTO, see age 6 OR RT ORTO, See ages 7, - R osition 8-4 X T OL 7 & 78 SZS OLY OTT Y () Q SOT STSRS 0 RT R (OT SS) SSLY TYS*.. S L (4) T OLS V L osition () Q SOT STSRS 0 RT (OT SS) R OTT Y 8-4 X T OL 7 & 78 SZS OLY.. S V.. (4) T OLS on.. LL SOS S 6 40T L - ounting 700 Q700 R700 80T T 80T 0T 6 80T 0T 0T Q R- ounting 6 40T 80T 0 S T oles.. Low Speed Shaft V -ey Length pprox. eight(ls.) # / #0-..8 / #0-..8 / See age / / or / / ey / / nformation / / / / / / * See ssemblies and ounting ositions, age 8. ** or an s, see age 0. See age 8 for available bore sizes. nput may be rotated clockwise or counterclockwise. The S style is recommended for direct replacement only. 4Z lange imensions: 700 =.6 : Q700 = 4. : R700 = 4.76 Q L an o.** -48-7/8 4