G J. For Assembled Carriage Load Capacities 42

Size: px

Start display at page:

Download "G J. For Assembled Carriage Load Capacities 42"

Christine Lawson
5 years ago
Views:

1 Carriages ssembled carriages for all sizes of bearing are available to fit all sizes of beam incorporating corner mounted slides. Carriages are also available to fit double edge slides. Carriages are supplied with through hole fixing bearings to facilitate direct removal from the slide. Cap wipers 32 and lubricators 34 are available as options. Carriage plates are fully machined from high strength aluminium alloy supplied clear anodised with tapped holes provided in convenient positions to enable other components to be attached. ssembled carriages can be factory adjusted to suit the corresponding beam assembly 24. Special carriages can be readily supplied and material can be removed in unwanted areas to reduce weight. L S Scraper lates (optional) 32 E C Single Edge Slide earing shown without cap wiper fitted K 6 x M Tapped holes for customer use G Cap wiper x 4 (optional) *3 Slide lubricator x 4 (optional) *3 or ssembled Carriage Load Capacities 42 art umber or Use With Slides or Use With eam Slide osition *1 earing C U S 25 - Ø U C... SS C or C Ø U SS or E Ø U W... SS C or G Ø U S 25 - Ø U C... SS C or C Ø U SS or E Ø U W... SS C or G Ø U S 25 - Ø U C... SS C or C Ø U SS or E Ø U W... SS C or G Ø U SS or E Ø U W... SS C or G Ø U SS or E Ø U W... SS C or G Ø or other options with cap wipers visit and select datasheet o. 9 S2 Cap Wiper options. otes: 1. or slide position information please refer to The U12025 carriage requires high type back plate W ccess to cap wiper and lubricator fixing screws is from the top of the carriage for ease of adjustment and removal. or cap wiper and lubricator mounting hole positions please refer to 32 & 34 respectively. 4. The ordering details opposite relate to assembled carriages only. or ordering details concerning beams assembled with slides and to specify the assembled carriage to be ready adjusted and mounted, please refer to or the stainless versions, bearing assemblies and all fixing screws are in stainless steel. Carriages plates are aluminium with clear anodised finish. special US approved surface treatment for greatly enhanced corrosion resistance is available on request. 6. This table states dimensions for precision grade slides, for assembled dimensions based on commercial grade slides add 0.2mm to dimensions &. ther dimensions will not be affected. 26

2 Carriages The drawings below show epco S2 carriages assembled together with beams with slides in the basic combinations possible. Cap wipers are illustrated for worst case dimensions. earings only or lubricators will be slightly more compact 18,19 & 34. U.. - ouble edge *2 U.. - arrow U..W - Wide Slides earings U...W - Wide U... - arrow U..C - Compact C ssembled ssembled Systems E G K L M Thread size *6 *6 S kg x depth M10x M10x M10x M10x M10x M10x M10x M10x M12x M12x M12x M12x M12x M12x M16x M16x ack riven Carriages T-uts 38 C XYZ Technical rdering Example *4 SS U 64 25C L CW Stainless version *5 CW = Cap wipers art umber CW4S = Cap wipers + utboard scrapers earing size L = Slide lubricators Carriage type 27

3 ack riven Carriages epco S2 rack driven carriages are available to suit the corner mounted options for construction beam assemblies or for other mounting arrangements with slides spaced the same distance apart 27. They are designed to engage with single edge V slides with integrated racks in precision, stainless steel and commercial grade options. They have all the benefits of the assembled carriages with the addition of a high performance rack and pinion drive facility. ack driven carriages can be supplied with an automatic lubrication device which will apply a controlled amount of grease direct to the teeth 36. art umber or Use With ack ptions *1 eam Slide earing 2.5,3,4,5=mod, S=, = 2.5S S S C E U C.. 25C SS 25 Ø U C..3 25C SS 25 Ø U SS 25 Ø U W.. 25 SS 25 Ø U C.. 25C SS 25 Ø U SS 25 Ø U W.. 25 SS 25 Ø U C.. 25C SS 25 Ø U SS 25 Ø U W.. 25 SS 25 Ø U SS 33 Ø U W.. 33 SS 33 Ø U SS 33 Ø U W.. 33 SS 33 Ø or installation and adjustment procedure visit and select datasheet o. 8 S2 ack riven Carriages. or ack riven Carriage Load Capacities 42 L G K or dimensions and specification of the drive flange assembly and C geared motor C pinion (optional) 36 6 x W - Customer mounting holes rive pinion M C geared motor (optional) 31 Slide lubricators x 4 (optional) *5 34 Concentric bearings fitted this side E inion adjuster for correct mesh S T Cap wipers x 4 (optional) *5 32 utomatic lubrication unit (optional) 36 bevel gearbox with hollow shaft 31 rive flange U V otes: 1. Module 2.5 and 4 helical racks have a left handed helix angle of 30, available as a standard option on SS25 and SS33 slides respectively. 2. ssembled carriage weights do not include motor & gearbox, 31 for details. 3. Motor mounting position 3,4,5 & 8 are not compatible with the standard mounting position of the automatic lubrication unit, alternative positions of the lubrication unit are available. 4. SS versions have all stainless steel components except carriage and drive flange body which are aluminium clear anodised (enhanced anti-corrosion finish available on application). Cap wipers are plastic, geared motor is standard. 5. or cap wiper mounting hole positions 32. or lubricator mounting hole positions 26 &

4 ack riven Carriages ack driven carriages incorporate a strong drive flange assembly with micro adjustment facility to achieve correct mesh between pinion and rack 30. The standard design is for connection with epco supplied C geared motors 31 this being the most economical means of achieving point to point linear motion. Speed and acceleration can also be controlled via an C speed controller which epco also supplies. Modified or special drive flanges can be readily supplied to suit customers own motor gearbox, including servo and stepper types. Slides M S T G K L U V W kg *2 Thread size x depth M10x M10x M10x M10x M10x M10x M10x M10x M10x M10x M12x M12x M16x M16x Special shape and size carriages, and carriages to suit different slide spacing, can be readily supplied. earings ssembled ssembled Carriages etaining washer & screw djustment feature to set rack and pinion engagement utomatic lubrication unit (optional) 36 Carriage plate rive lange ssembly Shaft housing with mounting flange and high load roller bearing for shaft support 30 rive pinion Geared motor (optional) 31 Customers ordering rack driven carriages fitted with geared motors should specify the orientation required (1-8) *3, and the terminal box position (-) by indicating these requirements in the ordering details for the geared motor rive lange ssembly 30 inions *3 C utomatic 36 rdering Example SS U 64 25C 3S L CW L Stainless version *4 pinion assembly art number CW = Cap wipers earing size CW4S = Cap wipers + utboard scrapers Carriage type L = Slide lubricators 26 & 27 for range available ack Type 2.5S = Module 2.5, 2.5 = Module 2.5 3S = Module 3, 4 = Module 4, 5S = Module 5 Geared motor should be ordered as a separate item 31. C Geared Motor 31 C XYZ Technical

5 Your partner in quality engineering products since 1986 Thank you for viewing product information on TE s range of engineering components. ow please contact us at the nearest office to you for any further information, prices and availability: USTLI & ew Zealand US, South merica & Canada T.E.. Transmissions ty Ltd T.E.. Machine Components Inc. Tahiti oad abney oad Tiaro Qld 4650 ichmond Virginia ustralia US h: 61-(0) h: ax: 61-(0) ax: sales@tea.net.au sales@teausa.net You are assured of prompt and efficient service at all time.

Assembled Double Edge Ring System

Assembled Double Edge Ring System 22 ssembled Double Edge ing System ssembled Double Edge ing System When using Hepcootion Double Edge ing Slides encircled by bearings as shown below it is recommended that two concentric bearings should