RGB Catalogue SERIES RGB TECHNICAL CATALOGUE. ust 2008

Transcription

1 RGB Catalogue 3 3 SERIES RGB TECHNICAL CATALOGUE August ust

2 4 RGB Catalogue

3 RGB Catalogue 5 1 Catalogue cover sheet 3 Overview of catalogue pages 4 Construction description 5 System description 6 System description 7 Installation of Profiles/Corner connectors 8 Installation of T-connectors/Accessories/Gaskets 9 Installation of Mounting material/drilling tempates 10 Explanatory notes on preliminary calculations 11 Preliminary calculations table 12 Cross-section values 13 Nominal values for the thermal tranmission coefficient U f 14 Explanatory notes on table with U-values 15 Table Rated value /U-values 30% 16 Table with U-values 20% 17 Profiles 18 Profiles 19 Profiles 20 Profiles 21 Profiles 22 Profiles 23 Profiles 24 Glazing Table 25 Corner connectors 26 Corner connectors 27 T-connectors 28 Corner joints 29 Corner joints 30 T-profile connectors 31 Accessories 32 Drainage/Ventilation 33 Overview of intersection points 34 Intersection points 35 Intersection points 36 Intersection points 37 Intersection points 38 Intersection points 39 Intersection points 40 Intersection points

4 6 RGB Catalogue Windows: Heat-insulated compound profile system with large-volume EPDM multi-chamber center seal with preformed angles. Minor profile view widths due to hidden wing profiles. The RGB series is especially suitable for the use in facades. Uf values according to EN ISO Design values Uf,BW according to DIN V : Fittings: Commercially available fittings. Profiles are designed with 10mm notches according to the European sizes. Increased burglary safety possible due to safety class WK2. Design: Double wall, hollow composite profiles (three-chamber system) with even surfaced rebate bed. Dimensions*: Frame profiles: 75 mm installation depth (basic depth); window sashes 85 mm installation depth. Profile compound: Quality controlled, force-fit and form-fit compound with polyamide strips min. 25% reinforced with glass fibre by using melt thread. In order to improve the thermal insulation, the compound zone of the profiles is partly filled with polyurethane rigid foam. The hollow composite profiles are suitable for post-processing the surfaces. Joint permeability and driving rain sealing: Exposure Category C according to DIN * The dimensions for the built-in depth of the catalogue are standard gauges for the planning. The manufacturing dimensions for frames and sash profiles are 0,4mm over the nominal dimensions of the catalogue, the bar profiles 0,2mm.

5 RGB Catalogue 7 System Description 1. General This profile system includes heat-insulated, two-wall composite profiles (three-chamber system) for the production of windows and doors. Heat insulation is achieved by thermal separation of the inner and outer profile walls by means of glass-fibre reinforced isolating webs made of polyamide, with special melted wire inserts. The compound is manufactured force-fit and form-fit in the press plant by controlling the quality. In order to improve the thermal insulation, the hollow space between the isolating strips is partly filled with highly insulating polyurethane rigid foam. The design is in accordance with the state of the art and the directives and recommendations of the insulating glas, fittings and sealing materials manufacturers and meets the requirements of the Directive for the Proof of Stability of Composite Metal-Plastic Profiles of the German Institute for Construction Engineering,Berlin, as well as the requirements of the provisions regarding quality and testing of aluminium windows. The U f values of the profiles and profile combinations have been determined acc. to EN ISO and are given acc. to DIN V : 2002 in design values. The air permeability of joints and watertightness under heavy rain of the windows correspond to the exposure category C of DIN The construction of solid, safe and operational elements is guaranteed. The Code of Practice for the Processor in our latest main catalogue must be observed for the use and processing of our design. With our delivery of composite profiles you are also receiving our guarantee for this product. 2. System Scope This profile system includes window and door profiles for the construction of side-hung, turn and tilt, tilt and double sash windows, doors and parallel-slide-and-tilt doors. The main profiles include narrow and wide outer frame, sash, glazing bar, post and sill rail profiles. Additional profiles are respectively available for wall connections, as well as for expansion and decorative glazing bars. Glazing rebate strips for filling thicknesses (glazing thicknesses) from 18 to 45 mm are available. 2.1 Heat insulation This profile system contains window profiles for manufacturing swivel windows, tilt and turn windows and pivot windows. The main profiles comprise narrow and wide blind frames, sash and bar profiles. Due to the hidden sash profiles, only minor profile view widths are achieved. The RGB series is especially suitable for the use in facades. For wall connections, expansion and adornment bars, relative additional profiles are available. Glass rebates for priming thicknesses (glass thicknesses) are available depending on the catalogue. 2.1 Thermal insulation The heat-insulated construction contains frame and bar profiles with a frame profile depth of 75 mm and a sash profile depth of 85 mm, and is equipped with a large-volume, EPDM multistage middle sealing. Additionally, the glass rebate is shielded with EPDM multistage cover profiles on both sides of the filling against thermal radiation and air convection. The indicated nominal values for the thermal transmission coefficient Uf for single profiles and profile combinations are given in separate tables and are proven by the relevant test certificates of the Institute for Window Techniques Rosenheim e.v. 3. Construction 3.1 Maximum sash sizes Windows: Sash width mm Sash height mm max. Sash weight: 130 kg additional middle locks starting with 1250 mm sash height or width. 3.2 Statics The cross-sectional values of the profiles (idleness and resistance momenta etc.) are given in separate statics tables. 3.3 Connection of frame and bars The connection of the profiles corner brackets and T-connectors is achieved in both hollow chambers with glued-in aluminum corner brackets and T-connectors, which are fixated with spiral pinks or mechanical angle connection devises. The fabricator must ensure the water impermeability against mitres and shocks. This is especially valid for lower horizontal frame and bar profiles. All holes on corner brackets and T-connectors (continuous nuts of the glass rebate strips, clamping nuts in the rebate etc.), the front side of the basis profiles towards the frame profile etc. must be specially sealed (also in thin layers) with the appropriate elastic silicone or Thiokol sealing substance. 3.4 Middle sealing EPDM middle sealing as frame with 50 mm form angles. Gluing with the form angles is achieved with the contact glue cyanoacrylate glue). Cutting the sealing profile is calculated as follows: Sash size minus 100 mm (2 x 50 mm form angle) plus 0,5 %. Example: Sash size 1100 mm. Cutting the middle sealing = = 1005 mm. 3.5 Glazing Glazing with sealing substance-free rebate with preformed EPDM sealing profiles. In order to guarantee the venting (vapour pressure compensation) of the rebate area, holes are drilled in front of the middle sealing which lead to the outer air and have a minimum cross-section of 15x5 mm or 8 mm diameter. The holes are at the lowest point of the rebate and are foreseen at least twice in the lower horizontal. The outer holes are between the frame angle and the glazing block, a maximum of 100 mm away from the corner. It is suggested to make additional lateral holes on the upper side. Blocking is achieved on system s own glass rebate inserts. Blocking inhibits the insertion of air or water (condensate) in the rebate. If the glazing is done by using sealing substances, then you should consider the table Exposure groups for glazing windows by the Institute for Window Techniques e.v. Rosenheim.

6 8 RGB Catalogue System Description 3.6 Draining the construction The water inserting the pre-chamber (average pressure chamber) is guided directly outside over at least 2 pieces 28 x 12 mm water outlet holes which are in front of the middle sealing. These are approx. 120 mm away from the frame end and have a maximum distance of 600 mm. The holes are covered with drainage inserts. In case of downward drainage directly on the window sill or over the basis profile, the incoming water is drained off with 35 x 6 mm big water outlet slots. The number and position is the same as previously described. The corresponding water outlet slots in the AI basis profile should be displaced for 50 mm at the opposite of the slots in the frame profile Condensate water formation The formation of condensate water on the heat-insulated compound profiles is only then possible, if the relevant isolating glass panes (formation of perspiration) would appear with the corresponding inner and outer temperatures and the air humidity of the inner room. Additionally installed profiles on the outside, as rolling shutters or window sills, change in a negative manner the inner surface temperatures of these profiles and thus the behavior of the condensate water. The fabricator must be careful not to allow any cold air in the inner peels of the frame profiles when the elements have been installed. This is especially important if rolling shutters have been installed over the elements. In this case, the frame profile must be covered on the front side with fixed sealing strips from PUR or polystyrene rigid foam. Thermal bridges should be avoided. 7,5 12 A guarantee regarding the adequacy after completion of this procedure can be granted only if the profiles are delivered immediately after manufacture to the anodic plant and are processed there directly. We do not take any responsibility for this procedure with regards to the delivery of products that originate from the stock of inventory. 4.2 Colour coating The colour coating must be carried out according to the Quality and test specifications for coating RAL-RG 631 parts. Coating theprofiles is achieved by heating powder lacquerin a hardening furnace. Generally, powder lacquers on polyester basis are used. The layer strength should be 60 to max. 120 μm. The layered profiles are with a max. 175 ± 10 C object temperature and a heatingduration in a hardening furnace of approx. 20 minutes (after achieving the object temperature). The aluminum profiles should be pre-processed carefully according to DIN for an acceptable colour coating.chromating is unavoidable. 5. Dimensioning the compound profiles The dimensions mentioned in the catalogue are planning dimensions. Due to the differenttreatment of the surfaces, they should not be used as control dimensions for the compoundprofiles delivered by us. 4. Surface handling For handling surfaces, the FWB guidelines State 11/91 are valid. A different colour scheme of the profiles can be done before bonding the half shells. 4.1 Anodic oxidation (anodic treatment) For the anodic oxidation of the aluminum parts, DIN is valid. The quality and test specifications on Anodized aluminum RAL-RG 661 must be considered before the anodic treatment. The anodic manufactured oxide layers must have a minimum layer thickness of 20 μm. Special care must be shown to the material that will be anodically oxidated according to procedure E6 (stained and anodized).

7

8 10 RGB Catalogue Corner connectors Order No. Designation Required installation material Quantity Order No. Profile Code AE Corner connector for profiles AH275-RG4240, AH275-RG4245, outside 2 pcs AE AH900-TF495 AE Corner connector for profiles AH275-RG4240, AH275-RG4245, outside 2 pcs AE AH900-TF495 AE Corner connector for profiles AH275-RG4120, outside 2 pcs AE AH900-TF495 AE Corner connector for profile AH275-RG4130, outside 2 pcs AE AH900-TF498 AE Corner connector for profiles AH275-RG4120, AH275-RG4240, AH275- RG4245, inside 2 pcs AE AH900-TF496 AE Corner connector for profiles AH275- RG4130, inside 2 pcs AE AH900-TF499 AE Stiffening plate for profiles AH275-RG4120, AH275-RG4130, AH275-RG4240, AH275-RG4245, AH , outside AE Stiffening plate for T-shocks, outside, by connection with rebate depth 44m on both sides AE Corner connector for profile AH , inside 2 pcs AE AH900-TF495 AE Corner connector for profiles AH , outside 2 pcs AE AH900-TF483 AE Pressta corner connector for profiles AH , outside 2 pcs AE AH900-TF483 AE Pressta corner connector for profiles AH275-RG4210, inside 2 pcs AE AH900-TF483 AE Pressta corner connector for profiles AH275-RG4215, inside 2 pcs AE AH900-TF499 AE Pressta corner connector for profiles AH275-RG4210, AH275- RG4215, outside 2 pcs AE AH900-TF479 T- connectors Order No. Designation Required installation material Quantity Order No. Profile Code AE AE AE AE AE AE AE AE T-connector for profiles AH275-RG4240 and AH275-RG4245, outside on frame and bar profiles with 24mm rebate depth T-connector for profile AH275-RG4120, outside on frame and bar profiles with 24mm rebate depth T-connector for profile AH275-RG4130, outside on frame and bar profiles with 24mm depth T-connector for profiles AH275-RG4120, AH275- RG4240 and AH275-RG4245. inside on frame and bar profiles with 24mm rebate depth T-connector for profile AH275-RG4130, inside on frame and bar profiles with 24mm rebate depth T-connector for profile AH275-RG4120 outside on frame and bar profiles with 44mm rebate depth T-connector for profile AH275-RG4130, outside on frame and bar profiles with 44mm AH275-RG4120 rebate depth T-connector for profile AH275-RG4240 AND AH275-RG4245, outside on frame and bar profiles with 44mm rebate depth 1 pc AE AH900-TF649 1 pc AE AH900-TF649 1 pc AE AH900-TF649 1 pc AE AH900-TF650 1 pc AE AH900-TF650 1 pc AE AH900-TF536 1 pc AE AH900-TF536 1 pc AE AH900-TF536

9 RGB Catalogue 11 Accessories Order No. AE AE AE AE Designation Glazing bearing, horizontally under, min. 2 pieces per fixed glazing Glazing rebate, horizontally under, min. 2 pieces per fixed glazing Angled formed part for middle strip sealing AE Drainage insert, black Gaskets Order No. AE AE AE AA AA AE AE Designation Stroke gasket for window sash profiles, inside Outside glazing gasket frame, outside in the sash Central gasket (highly insulated) Glazing gasket 3 mm, inside Glazing gasket 7 mm, inside Glazing gasket 8 mm, inside Glazing gasket 12 mm, inside and outside Installation material Order No. Designation AE Roll pin 7 mm x 13.5 mm (cylindrical), for corner and T-connector AE Roll pin 7 mm x 18 mm (cylindrical) for corner and T-connector Drilling templates Order No. AE Designation Drilling template for Corner connector AE in profile AH275-RG4120, Corner connector AE in profile AH275-RG4120, Corner connector AE in profile AH275-RG4130, Corner connector AE in profile AH275-RG4130, T-connector AE in profile AH275-RG4120, T-connector AE in profile AH275-RG4120, T- connector AE in profile AH275-RG4130, AE Drilling template for T-connector AE in profiles AH275-RG4130 & AH275-RG4240, AE AE Drilling template for Drilling template for T-connector AE in profile AH275-RG4120 T-connector AE in profile AH275-RG4130 T-connector AE in profiles AH275-RG4240 & AH275-RG4245, Corner connector AE in profile AH Corner connectorae in profile AH

10 12 RGB Catalogue Measurement of pillars and latches Loading width: The loading width c1 or c2 results from bisecting the fields that are adjoined to the pillars or latches. Loading case: A loading case is understood to be a carrier standing without support on two pillars with trapezoidal or triangular load. The division of the loading surface is achieved by bisecting the angle. Allowed bending: Generally, fzul = 1/300 I (DIN 18056) The manufacturer of the isolating glass acknowledge this as max. bending of the position points of the support width I, although they limit the allowed bending in the partial area (bending between the position points of the largest partial area) to fzul. = 1/300 * I = 0,8 cm. Loading assumption: (DIN 1055, Part 4) Back pressure q = 0,5 kn/m2 (height over the area = 0-8 m) Back pressure q = 0.8 kn/m2 (height over the area = 8-20 m) Back pressure q = 1.1 kn/m2 (height over the area = m) Pressure coefficient c p = 0,8 + 1/4 = 1,0 Wind pressure w = q c p (kn/m2) Material information on solidity of the Al-Leg. AlMgSi 0,5 F22 (DIN 4113) Minimum tensile strength Bz = 22 kn/cm2 Minimum limit of elasticity d 0,2 = 16 kn/cm2 Allowed voltage {main load H): d zul = 95 N/mm2 Elasticity module E = 7000 kn/cm2 Using table I and II For the pillars or latches of single-paned fields Example A Table I should be used. For the pillars or latches of multi-paned fields Example B Table II should be used, if all partial areas = 240 cm. In example C, the biggest partial area of the pillar was measured with 320 cm. Since it is above 240 cm, for this area fzul = 0,8 cm or fzul. = /p/0,8 I = 320/0,8 I = 1/400 I This allowed bending of 1/400 I of the partial area is valid for the total pillar length of 460 cm. In order to determine the required idleness momentum I *, one must divide the value from the adjoining table II by 300 and then multiply it with 400.

11 RGB Catalogue 13 Table for determining the required idleness momenta Ix erf. [cm4] for aluminum (E= 7000 kn/m2). Loading fall: Carrier standing without support on two pillars, trapezoidal or triangular load. The indicated values are intended for the profile pre-measurement and do not replace any static measurement capable of testing. Table I Bending f = 1/300 I < 0,8 cm Conversion factors Tor the pillars or latches Determining the necessary idleness momenta For the pillars or latches of of single pane fields The determination is done according to the following sequence: multi-paned fields Table II should Table I should be used. 1. Determine the support width I in cm. be used, if all partial areas = 240 cm. Table II 2. Determine the loading width c1 and c2 in cm. Bending f = 1/300 I 180 3,2 4,7 6,0 7,2 8,1 8,8 9,2 9,4 3. Determine the idleness momentum lx erf. for the loading width c1 according to table I or II. 9,4 9,2 8,8 8,1 7,2 6 4,7 3, ,8 5,5 7,1 8,5 10,6 10,6 11,3 11,6 4. Determine the idleness momentum lx erf. for the loading width c2 according to table I or II ,7 8,5 7,1 5,5 3, ,4 6,5 8,4 10,1 12,7 12,7 13,6 14,1 14,3 5. Add the idleness momenta that were determined under 3 and ,4 6,5 4, ,1 7,5 9,7 11,8 15,0 15,0 16,2 16,9 17,3 6. Multiply the sum of the necessary idleness momenta with the factor from the wind pressure ,7 7,5 5, ,9 8,6 11,3 13,7 17,6 17,6 19,0 20,1 20,7 20, ,6 5, ,7 9,9 12,9 15,7 20,4 20,4 22,2 23,5 24,5 24, ,9 6, ,6 11,3 14,8 18,0 23,5 23,5 25,6 27,3 28,6 29,4 29, , ,0 13,3 17,4 21,3 27,9 27,9 30,6 32,8 34,5 35,7 36, , ,5 15,6 20,5 25,0 33,0 33,0 36,3 39,1 41,3 42,9 43,9 44, , ,2 18,2 23,9 29,2 38,7 38,7 42,7 46,2 49,0 51,1 52,6 53, ,2 21,0 27,7 33,9 45,1 45,1 49,9 54,1 57,6 60,4 62,4 63,6 64, ,3 24,2 31,9 39,2 52,3 52,3 58,0 63,0 67,3 70,8 73,5 75,3 76, ,7 27,8 36,6 45,0 60,3 60,3 67,0 73,0 78,2 82,5 85,9 88,4 89,9 90, ,3 31,7 41,8 51,5 69,2 69,2 77,0 84,0 90,2 95,5 99, ,2 36,1 47,6 58,6 78,9 78,9 88,0 96, ,4 40,8 53,9 66,4 89,7 89, ,9 46,0 60,8 75, ,7 51,7 68,3 84, ,9 57,9 76,6 94, ,4 64,7 85, ,3 72,0 95, ,6 79, ,3 88, ,5 97, , , , , Height above ground 0-8m 8-20m m Dynamic pressure q 0,5 kn/m2 0,8 kn/m2 1,1 kn/m2 Pressure coefficient c p 1,0 1,0 1,0 Wind pressure w = q c p 0,5 kn/m 2 0,8 kn/m 2 1,1 kn/m 2 Factor 1,0 1,6 2,2 Support width 1 (cm) Support width 1 (cm) Load width a [cm] Load width a [cm] The values are arranged for a wind pressure of 0,5 kn/m2. For the other wind pressures, you must multiply the determined idleness momentum with the corresponding factor.

12 14 RGB Catalogue Cross section values (ideal inertia moments) lx id [cm 4 ] x x' Profile Order No. Support width L [cm] {acc. to ifbt directive} AH275-RG ,15 33,22 36,33 38,30 40,15 41,63 42,27 AH275-RG ,88 36,96 40,80 43,29 46,11 47,56 48,39 AH275-RG ,07 23,49 24,89 25,74 26,30 27,13 27,88 AH275-RG ,67 22,92 24,21 25,00 25,86 26,41 26,52 AH275-RG ,60 36,60 40,40 42,80 45,60 74,00 47,80 AH275-RG ,00 38,50 42,60 45,30 48,30 49,90 50,80

13 RGB Catalogue 15 Nominal value for the thermal transmission coefficient Uf Fixed cross-sections Blind frames Moveable cross-sections Blind frames/bars and sash combination Outer view width Outer view width The nominal values of the thermal transmission coefficient Uf that are listed below were determined according to EN ISO Data in W/m2K Fixed cross-sections. Blind frames. Moveable cross-sections. Blind frame and sash combination. AH275-RG4210 with AE AH275-RG4215 with AE AH275-RG AH275-RG4130 Fixed cross-sections Bars Moveable cross-sections/ moveable fixed field Bars and sash combination AH275-RG4210 fixed field AH275-RG4215 fixed field 2X AH275-RG4215 with AE X AH275-RG4215 with AE / / AH275-RG AH275-RG4245 Note: The illustrated Uf values for fixed glazings were determined with an insulated insert in the area of the glass rebate of the blind frame or bar profiles on the basis of PUR rigid foam plates.

14 16 RGB Catalogue Determining the nominal values of the thermal transmission coefficient Uw from the tables of the EN ISO : 2000 and DIN V : Determining the nominal values of the thermal transmission coefficient LL for windows and french doors according to example 1: 1. Take the nominal value Uf from the Brökelmann table 1-3 according to EN ISO Classify the nominal value Uf and determine the Uf,Bw (rated value) in table 7 according to DIN V 4108B4: Transfer Uf,Bw in table F.1 or, otherwise, F.2 in order to determine the nominal value of the thermal transmission coefficient Uw according to EN ISO :2000 and DIN V Determine Ug value and read nominal value Uw in table F.1 or F.2. Caution: The nominal values contained in table F.1 and F.2 for windows and french doors Uw have been determined with standard window sizes 1,23m x 1,48m and have a frame surface percentage of 30% or 20%. Uf = Thermal transmission coefficient for frames. Uw = Thermal transmission coefficient for windows. Ug = Thermal transmission coefficient for glass. Ud = Thermal transmission coefficient for doors. Example 1: Table 7- Classification of Ur values from single profiles to a rated value UfBW for frames. DIN V : Ur value of the frame from Brokelmann Table 1-3 according to EN ISO i.e. 1,94W/m2K Ur value for single profiles W/m2K UfBw- rated value W/m2K <0,90 0,80 >0,90 <1,1 1 >1,0 <1,3 1,2 >1,3 <1,6 1,4 >1,6 <2,0 1,8 >2,0 <2,4 2,2 >2,4 <2,8 2,6 >2,8 <3,2 3,0 >3,2 <3,6 3,4 >3,6 <4,0 3,8 >4,0 7,0 Table F.1: Thermal transmission coefficient Uw for windows with a 30% frame surface percentage on the total window surface. DIN EN ISO :2000 Ug- glazing value based on the German Federal Bulletin or the DIN 673 standard i.e. 1,1 W/m2K Glazing type Single plated glazing Double plated isolating glazing Ug W/m2K Uf W/m2K 30% frame surface percentage 1,0 1,4 1,8 2,2 2,6 3,0 3,4 3,8 7,0 5,7 4,3 4,4 4,5 4,6 4,8 4,9 5,0 5,1 6,1 3,3 2,7 2,8 2,9 3,1 3,2 3,4 3,5 3,6 4,4 3,1 2,6 2,7 2,8 2,9 3,1 3,2 3,3 3,5 4,3 2,9 2,4 2,5 2,7 2,8 3,0 3,1 3,2 3,3 4,1 2,7 2,3 2,4 2,5 2,6 2,8 2,9 3,1 3,2 4,0 2,5 2,2 2,3 2,4 2,6 2,7 2,8 3,0 3,1 3,9 2,3 2,1 2,2 2,3 2,4 2,6 2,7 2,8 2,9 3,8 2,1 1,9 2,0 2,2 2,3 2,4 2,6 2,7 2,8 3,6 1,9 1,8 1,9 2,0 2,1 2,3 2,4 2,5 2,7 3,5 1,7 1,6 1,8 1,9 2,0 2,2 2,3 2,4 2,5 3,3 1,5 1,5 1,6 1,7 1,9 2,0 2,1 2,3 2,4 3,2 1,3 1,4 1,5 1,6 1,7 1,9 2,0 2,1 2,2 3,1 1,1 1,2 1,3 1,5 1,6 1,7 1,9 2,0 2,1 2,9 Uw- window value i.e. 1,5W/m2K

15 RGB Catalogue 17 Determining the nominal values of the thermal transmission coefficient for windows and French doors Uw for aluminum profiles. Table 7: Classification of Uf- values for UfBW - rated values Table 7 - Classification of Uf- values for single profiles to a Uf,BW- rated value for frames. DIN V : Ur value for single profiles W/m2K UfBw- rated value W/m2K <0,90 0,80 >0,90 <1,1 1 >1,0 <1,3 1,2 >1,3 <1,6 1,4 >1,6 <2,0 1,8 >2,0 <2,4 2,2 >2,4 <2,8 2,6 >2,8 <3,2 3,0 >3,2 <3,6 3,4 >3,6 <4,0 3,8 >4,0 7,0 Table F.1: For a 30% surface percentage of the frame. Table F.1: Thermal transmission coefficient Uw for windows with a 30% frame surface percentage on the total window surface. DIN EN ISO :2000 Glazing type Single plated glazing Double plated isolating glazing Triple plated isolating glazing Ug W/m2K Uf W/m2K 30% frame surface percentage 1,0 1,4 1,8 2,2 2,6 3,0 3,4 3,8 7,0 5,7 4,3 4,4 4,5 4,6 4,8 4,9 5,0 5,1 6,1 3,3 2,7 2,8 2,9 3,1 3,2 3,4 3,5 3,6 4,4 3,1 2,6 2,7 2,8 2,9 3,1 3,2 3,3 3,5 4,3 2,9 2,4 2,5 2,7 2,8 3,0 3,1 3,2 3,3 4,1 2,7 2,3 2,4 2,5 2,6 2,8 2,9 3,1 3,2 4,0 2,5 2,2 2,3 2,4 2,6 2,7 2,8 3,0 3,1 3,9 2,3 2,1 2,2 2,3 2,4 2,6 2,7 2,8 2,9 3,8 2,1 1,9 2,0 2,2 2,3 2,4 2,6 2,7 2,8 3,6 1,9 1,8 1,9 2,0 2,1 2,3 2,4 2,5 2,7 3,5 1,7 1,6 1,8 1,9 2,0 2,2 2,3 2,4 2,5 3,3 1,5 1,5 1,6 1,7 1,9 2,0 2,1 2,3 2,4 3,2 1,3 1,4 1,5 1,6 1,7 1,9 2,0 2,1 2,2 3,1 1,1 1,2 1,3 1,5 1,6 1,7 1,9 2,0 2,1 2,9 2,3 2,0 2,1 2,2 2,4 2,5 2,7 2,8 2,9 3,7 2,1 1,9 2,0 2,1 2,2 2,4 2,5 2,6 2,8 3,6 1,9 1,7 1,8 2,0 2,1 2,3 2,4 2,5 2,6 3,4 1,7 1,6 1,7 1,8 1,9 2,1 2,2 2,4 2,5 3,3 1,5 1,5 1,6 1,7 1,9 2,0 2,1 2,3 2,4 3,2 1,3 1,4 1,5 1,6 1,7 1,9 2,0 2,1 2,2 3,1 1,1 1,2 1,3 1,5 1,6 1,7 1,9 2,0 2,1 2,9 0,9 1,1 1,2 1,3 1,4 1,6 1,7 1,8 2,0 2,8 0,7 0,9 1,1 1,2 1,3 1,5 1,6 1,7 1,8 2,6 0,5 0,8 0,9 1,0 1,2 1,3 1,4 1,6 1,7 2,5

16 18 RGB Catalogue Determining the nominal values of the thermal transmission coefficient for windows and French doors Uw for aluminum profiles. Table F0.2: For a 20% surface percentage of the frame Table F0.2: Thermal transmission coefficient Uw for windows with a frame surface percentage of 20% on the total window surface. DN EN :2000 Glazing type Single plated isolating glazing Double plated isolating glazing Tri[ple plated isolating glazing Ug W/m2K Uf W/m2K 1,0 1,4 1,8 2,2 2,6 3,0 3,4 3,8 7,0 5,7 4,8 4,8 4,9 5,0 5,1 5,2 5,2 5,3 5,9 3,3 2,9 3,0 3,1 3,2 3,3 3,4 3,4 3,5 4,0 3,1 2,8 2,8 2,9 3,0 3,1 3,2 3,3 3,4 3,9 2,9 2,6 2,7 2,8 2,8 3,0 3,0 3,1 3,2 3,7 2,7 2,4 2,5 2,6 2,7 2,8 2,9 3,0 3,0 3,6 2,5 2,3 2,4 2,5 2,6 2,7 2,7 2,8 2,9 3,4 2,3 2,1 2,2 2,3 2,4 2,5 2,6 2,7 2,7 3,3 2,1 2,0 2,1 2,2 2,2 2,3 2,4 2,5 2,6 3,1 1,9 1,8 1,9 2,0 2,1 2,2 2,3 2,3 2,4 3,0 1,7 1,7 1,8 1,8 1,9 2,0 2,1 2,2 2,3 2,8 1,5 1,5 1,6 1,7 1,8 1,9 1,9 2,0 2,1 2,6 1,3 1,4 1,4 1,5 1,6 1,7 1,8 1,9 2,0 2,5 1,1 1,2 1,3 1,4 1,4 1,5 1,6 1,7 1,8 2,3 2,3 2,1 2,2 2,3 2,4 2,5 2,6 2,6 2,7 3,2 2,1 2,0 2,0 2,1 2,2 2,3 2,4 2,5 2,6 3,1 1,9 1,8 1,9 2,0 2,0 2,2 2,2 2,3 2,4 2,9 1,7 1,6 1,7 1,8 1,9 2,0 2,1 2,2 2,2 2,8 1,5 1,5 1,6 1,7 1,8 1,9 1,9 2,0 2,1 2,6 1,3 1,4 1,4 1,5 1,6 1,7 1,8 1,9 2,0 2,5 1,1 1,2 1,3 1,4 1,4 1,5 1,6 1,7 1,8 2,3 0,9 1,0 1,1 1,2 1,3 1,4 1,5 1,6 1,6 2,2 0,7 0,9 1,0 1,0 1,1 1,2 1,3 1,4 1,5 2,0 0,5 0,8 0,8 0,9 1,0 1,1 1,2 1,2 1,3 1,8 Note: The calculation for the tables F.1 and F.2 was done with *Ψ- values from Appendix E of the DIN EN ISO :2000 for glass distance holder from aluminum and steel (rust-proof steel).

17 RGB Catalogue 19 AH275-RG Frame profile Dev. anod.: 442/365* mm W=1.769 kg/m 7,5 5 AE ATTENTION: Control first the overhead light fittings. AE ,2 5 7,5 AE AE AE AE ,5 70, AH275-RG4130 Frame profile Dev. anod.: 482/385* mm W=1.975kg/m 75,2 5 7,5 7,5 5 AE AE AE AE AE AE ,5 70,7 * Handling for the connected profile

18 20 RGB Catalogue AH ,5 26,5 44 Frame profile 4 Dev. anod.: 475/354* mm W=1,734 kg/m AE ,2 19,5 AE AE ,5 AE AE ,5 70,7 90 * Handling for the connected profile

19 RGB Catalogue 21 Φ4 n4 Φ7 n7 Roll pin AE Roll pin AE ,2 8,3 Corner bracket Nr. AE from profile AH900-TF483 Stiftening plate Nr. AE for frame profiles Corner bracket Nr. AE from profile AH900- TF495 6,5 26,5 27 AH275-RG , , ,2 32 AE , ,5 15, * Handling for the connected profile

20 22 RGB Catalogue 56 AH275-RG4210 Sash profile Dev. anod.: 367/313* mm W=1.453kg/m AE AE This profile is not constantly stored 56 AH275-RG4215 Sash profile Dev. anod.: 367/313* mm W=1.449kg/m AE AE * Handling for the connected profile

21 RGB Catalogue AH275-RG4240 Transom profile Dev. anod.: 367/313* mm W=1.895kg/m 70, AE AE AE AE AE AE AE , AH275-RG4245 Transom profile Dev. anod.: 367/313* mm W=2.017kg/m 70, ,5 4 AE AE AE AE AE AE AE * Handling for the connected profile

22 24 RGB Catalogue 15,9 AH900-TF469 Glass rebate for sash profiles Dev. anod.: 100 mm W=0.097kg/m 10,7 18 AE ,5 20 AH900-TF537 Adaptor profile for fest glazing Dev. anod.: 162 mm W=0.358kg/m AH900-TF464 Glazing bead Dev. anod.: 193 mm W=0,325 kg/m

23 RGB Catalogue 25 20,6 AH900-TF538 Glazing position profile Dev. anod.: 157 mm W=0.317kg/m 28,5 18 AE Profile is at the bottom horizontally fitted towards the blocking Length = 100 mm (also as AE ) AE AE Countersunk steel head screw 4,8x25 DIN 7971

24 26 RGB Catalogue Frame, glazing bar and door sash profiles Installation depth 75mm Window sashes Installation depth 85mm A Glazing thickness B Clearance of glazing seal, inside C Glazing bead width A Glazing thickness B Clearance of glazing seal, inside C Glazing bead width 24 AA =7mm AH900-TF464=27mm 28 AA =3mm AH900-TF464=27mm 24 AE =12mm 32mm 28 AE =8mm 32mm 12 A B C A B C 85 AE Profile is at the bottom horizontally fitted towards the blocking Length mm (also as ) ATTENTION: Theoretical nominal measurenents! All details are based in theoretical nominal measurements. Due to the tolerances of the individual building parts, there is a possibility for deviations. If applicable, this must be taken into consideration and should be controlled by a practical trial installation for safety reasons.

25 RGB Catalogue AH900-TF479 Corner connector profile W=1,153 kg/m Scale: 1: AH900-TF483 Corner connector profile W=2,881 kg/m 65 Scale: 1: ,4 AH900-TF495 Corner connector profile W=2.285kg/m 65 Scale: 1: AH900-TF496 Corner connector profile W=2,422 kg/m 65 Scale: 1:2

26 28 RGB Catalogue ,4 AH900-TF498 Corner connector profile W=2,673 kg/m 66,4 Scale: 1: AH900-TF499 Corner connector profile W=2,782 kg/m 70 Scale: 1:2 AE Reinforcement plate for corner brackets Scale: 1:2 AE Reinforcement plate for T-connectors Scale: 1:2

27 RGB Catalogue 29 11,5 AH900-TF536 T-connector profile W=0,999 kg/m 70,1 11,5 AH900-TF649 T-connector profile W=0,813 kg/m 50,1 13 AH900-TF650 T-connector profile W=0,911 kg/m 46,5 19,4

28 30 RGB Catalogue Corner connectors Frame profile AH275-RG4120 8,5 7 7 Roll pin AE Roll pin AE , Corner connector Nr. AE From profile AH900-TF495 16,4 Corner connector Nr. AE For frame profiles Frame profile AH275-RG Roll pin AE Roll pin AE ,5 8,5 Corner connector Nr. AE From profile AH900-TF ,4 Stiftening plate Nr. AE For frame profiles Corner connector Nr. AE From profile AH900-TF Stiftening connector Nr. AE From profile AH900-TF499

29 RGB Catalogue 31 Sash profile AH275-RG4210 Corner connector Nr. AE from profile AH900-TF479 Corner connector Nr. AE from profile AH900-TF483 Sash profile AH275-RG4215 Corner connector Nr. AE from profile AH900-TF479 Corner connector Nr. AE from profile AH900-TF499

30 32 RGB Catalogue Reinforcement plate AE x in each T-shock Roll pin AE b 25 Roll pin AE , b 8,5 56 8,5 36 Compound Profile Inner peels of T-connectors Size b Outer peels of T-connectors 24mm 44mm AH275-RG4120 AE AE AE AH275-RG4130 AE AE AE Size b AH275-RG4240 AE AE AE AH275-RG4245 AE AE AE

31 RGB Catalogue 33 Accessories are shown smaller 100 AE Glazing position profile for fixed glazing from profile AH900-TF538 AE Glazing rebate for fixed glazing AE Angled formed part 50x50 mm for middle sealing AE AE black Drainage insert 28 7, Gaskets AE Vulcanized corner gasket for AE AE Outside gasket in sash from sealing AE AE Stroke gasket Sash profile, inside AE Central gasket See angle formed part AE AA Glazing gasket inside, 3 mm 7 AA Glazing gasket inside, 7 mm 8 4 AE Glazing gasket inside, 8 mm 12 4 AE Glazing gasket inside and outside, 12 mm Roll Pins 4 AE AE AE ,5 18

32 34 RGB Catalogue AE AH900-TF469 AH275-RG4215 Ventilation in sash 28 AE Drainage 12 7,5 AE AH275-RG AE AE black Drainage insert AH AE The profile section is at the bottom horizontally fitted towards the blocking AH Drainage 12 7,5 20 AH275-RG4120 Bevel the sealing entry on the isolating strips in the drainage area

33 RGB Catalogue 35 Overview of intersection points Views from the outside fixed sash fixed fixed sash fixed fixed sash sash sash sash fixed sash fixed sash fixed Glass size Glass size

34 36 RGB Catalogue Section 1 Frame dimension Rebate dimension Glass dimension AH275-RG4120 AH900-TF537 AE Section 2 Frame dimension Rebate dimension Glass dimension AH900-TF537 AH275-RG4130 AE

35 RGB Catalogue 37 Section 3 AE Glass dimension Rebate dimension Frame dimension AE AH900-TF538 The profile section is at the bottom horizontally fitted towards the blocking AH900-TF AH275-RG Section AE AH900-TF469 AE AE Glass dimension Rebate dimension Sash dimension 5 AH275-RG Frame dimension AE AH275-RG

36 38 RGB Catalogue Section 4 28 AE AH275-RG Frame dimension Sash dimension Rebate dimension Glass dimension AH275-RG4120 AE AE AH900-TF469 AE Section 5 Frame dimension Sash dimension Rebate dimension Glass dimension AH275-RG4215 AE AH275-RG4130 AE AE AE AH900-TF

37 RGB Catalogue 39 Section Frame dimension Sash dimension Rebate dimension Glass dimension AE AH275-RG4210 AH275-RG AE AE AH900-TF469 AE Section 5 Frame dimension Sash dimension Rebate dimension Glass dimension AH275-RG4210 AE AH275-RG4130 AE AE AE AH900-TF

38 40 RGB Catalogue Section Frame dimension Sash dimension Rebate dimension Glass dimension AE AH275-RG4215 AH275-RG AE AE AE AH900-TF469 AE Section Frame dimension Sash dimension Rebate dimension Glass dimension AH275-RG4210 AE AH275-RG4240 AE AE AE AE

39 RGB Catalogue 41 Section 9 Frame dimension Sash dimension Rebate dimension Glass dimension AE AE AH275-RG4215 AH900-TF469 AE AE AH275-RG4245 AH275-RG4215 AE AE

40 42 RGB Catalogue Section Frame dimension Rebate dimension Glass dimension AH275-RG4240 AH900-TF537 AE Section Frame dimension Rebate dimension Glass dimension AH900-TF537 AH275-RG4245 AH900-TF537 AE

41 BALKAN NETWORK GREECE - BALKAN SA Head Office: Athens 11th km Nat.Road Athens-Lamia, Metamorphosi Tel.: , Fax: info@balkan.gr Iraklio: , Fax: Larissa: , Fax: Τhessaloniki: , Fax: Τhiva: Tel.: , Fax: Extrusion Industry 79th km Nat. Road Athens-Lamia, Ipato Thivon Tel.: , Fax: factory@balkan.gr ROMANIA - BALKAN RO Head Office: Bucharest B-dul Iuliu Maniu 333, Sector 6 Tel.: , Fax: balkanro@balkanro.ro Alba Iulia: , Arad: , Bacau: Βrasov: , Cluj-Napoca: , Constanta: Craiova: , Iasi: , Τimisoara: DEALERS Galati: Alprovest, tel/fax: , Pitesti: Conarg, tel/fax: Satu Mare: Neptun, tel/fax: , Sibiu: Roa Design, tel/fax: Ploiesti: Rolir, tel/fax: UKRAINE - BALKAN UA Head Office: Kiev Moskovsky Av. 6 Tel./Fax: /7858 Κharkov: Odessa: , , BULGARIA - BLK BG Ηead Office: Sofia 8 Malashevska Str Tel.: /91, Fax: office@blk-bg.com CZECH REPUBLIC ALUMONT BUILDING A.S. DEALER Hradni-Slazska 27/37, Ostrava Tel./Fax: alumont@alumont.cz RUSSIA MGM LTD DEALER Promzona 16 Str.-Armavir, Krasnodar Tel./Fax: armoz@inbox.ru BELARUS SOL-FARM DEALER Kalvariyskaya 60/2H, Minsk Tel./Fax: sol-farm@mail.ru