REGULATED VENTILATION FOR LIFT SHAFTS SIMPLE AND EFFICIENT BLUEKIT VENTILATION FLAPS EFFICIENCY

Transcription

1 REGULATED VENTILATION FOR LIFT SHAFTS SIMPLE AND EFFICIENT BLUEKIT VENTILATION FLAPS INNOVATION SAFETY w w w.b l u ek i t.eu EFFICIENCY

2 The ventilation components constitute a key factor for ventilation regulation and optimization. They are crucial for the execution of an efficient energetic concept and contribute to the decrease of building operating costs. It is possible to combine our BlueKit system with louvre windows or ventilation flaps which are in accordance with EN , together or without protection accessories such as weather protection grilles or roof vents. HORIZONTAL MOUNTING in the shaft head/on the roof VERTICAL MOUNTING in the shaft/on the facade Abbreviations: - HV: Horizontal vertical - TF: Thermo Flap - LF: Louvre window - S: Sheet steel - A: Aluminum

3 Contents Horizontal mounting Ventilation flap JK-180 HV... 4 Ventilation flap JK-180 HV-dB... 6 Roof vent JK-180 HVC... 8 Roof vent with blades JK-180 HVL Insulated roof vent TF (Thermo Flap) Vertical mounting Ventilation flap with weather protection grille JK-180 HV ALAS Insulated louvre windows S9-iVt-05 LF-MR Tairmo-LF-MR Modernisation Horizontal and vertical mounting Ventilation flap JK Ventilation flap JK-190-dB Horizontal mounting JK-190 ceiling-corner mounting (accessories)... 22

4 Ventilation flap JK-180 HV Description Smoke and heat exhaust ventilation (SHEV) device allowing a flush-mounted closure of the permanent lift shaft opening. The flap is designed for a horizontal and integrated installation inside the opening. The flap s spring return motor ensures its opening in case of power failure. Characteristics Flush installation Easy connection to exterior ventilation shaft Possible combination with roof vent Easy installing, easy access to motor Louvres made of aluminum profile, streamlined and torsion-resistant Delivered and assembled with profiled mounting plate Pre-assembled and pre-cabled motor Motor cabling with RJ45 connector for easy connection to BlueKit system Motor with positive safety function in case of power failure The most efficient solution for new buildings Spring return motor certified according to: EN Supplementary products Sealing tape expanding, used for sealing between the ventilation flap and shaft wall (included in the mounting set) Technical specification JK-180 HV Louvres Aluminium Seals EPDM-rubber Material Profiled sheet steel, dimensionally stable Thickness 1,5 mm Spring return motor Power supply 24 VAC/DC Torque 20 Nm Functional safety cycles (EN certification) Service life emergency positions (manufacturer specifications) Run-time Sound power level Closing via motor 150 sec. Opening via spring return 20 sec. Closing via motor 40 db Opening via spring return 62 db 4 BlueKit ventilation flaps - September 2017

5 Ventilation flap JK-180 HV MOUNTING FROM THE ROOF* Section B-B Section A-A MOUNTING FROM THE SHAFT Section B-B Section A-A Spring return motor dimensions Articles and dimensions - JK-180 HV Designation acc. to flap opening (mm) BxH 360x x x x x x1200 Net ventilation surface (m 2 ) 0,10 0,23 0,41 0,62 0,90 1,22 Recommended opening dimensions (mm) B1xH1 590x x x x x x1290 Minimal opening dimensions (mm) B1xH1** 530x x x x x x1290 Mounting plate dimensions (mm) B2xH2 740x x x x x x1440 Article number Other dimensions available upon request ** When using the minimal opening, dimensions demounting of the flap is necessary for the maintenance or replacement of the motor. Application For installation from the shaft, the RJ45 connection cable is placed on the shaft side and tightened through the cable joint in order to guarantee airtightness. The sealing tape is then attached on the edge of the mounting plate which faces the wall. Finally, the ventilation flap is placed in the opening and fixed through the drilling holes of the mounting plate with wall anchors. * Depending on the installation position, the maintenance of the flap might have to occur on the roof. By way of precaution we point out that applicable accident prevention regulations must be observed. September BlueKit ventilation flaps 5

6 Ventilation flap JK-180 HV-dB Description Smoke and heat exhaust ventilation (SHEV) device allowing a flush-mounted closure of the permanent lift shaft opening. The flap is designed for a horizontal and integrated installation inside the opening. The flap is equipped with a low-noise direct current motor. Characteristics Easy connection to exterior ventilation shaft Possible combination with roof vent Easy installation, easy access to motor Louvres made of aluminum profile, streamlined and torsion-resistant Delivered and assembled with profiled mounting plate Pre-assembled and pre-cabled motor Motor cabling with RJ45 connector for easy connection to BlueKit system Low-noise direct current motor Low noise level Direct current motor certified according to: EN Supplementary products Sealing tape expanding, used for sealing between the ventilation flap and shaft wall (included in the mounting set) 6 Technical specification Louvres Seals Material Thickness Power supply Torque Functional safety Run-time Sound power level JK-180 HV-dB Aluminium EPDM-rubber Profiled sheet steel, dimensionally stable 1,5 mm Direct current motor 24 VDC 10 Nm cycles (EN certification) ca. 4 sec. ca. 25 db BlueKit ventilation flaps - September 2017

7 Ventilation flap JK-180 HV-dB MOUNTING FROM THE ROOF* Section B-B Section A-A MOUNTING FROM THE SHAFT Section B-B Section A-A Direct current motor dimensions Articles and dimensions - JK-180 HV-dB Designation acc. to flap opening (mm) BxH 360x x x x x x1200 Net ventilation surface (m 2 ) 0,10 0,23 0,41 0,62 0,90 1,22 Recommended opening dimensions (mm) B1xH1 590x x x x x x1290 Minimal opening dimensions (mm) B1xH1** x x x x x x1290 Mounting plate dimensions (mm) B2xH2 740x x x x x x1440 Article number Other dimensions available upon request ** When using the minimal opening, dimensions demounting of the flap is necessary for the maintenance or replacement of the motor. Application For installation from the shaft, the RJ45 connection cable is placed on the shaft side and tightened through the cable joint in order to guarantee airtightness. The sealing tape is then attached on the edge of the mounting plate which faces the wall. Finally, the ventilation flap is placed in the opening and fixed through the drilling holes of the mounting plate with wall anchors. * Depending on the installation position, the maintenance of the flap might have to occur on the roof. By way of precaution we point out that applicable accident prevention regulations must be observed. September BlueKit ventilation flaps 7

8 Roof vent JK-180 HVC Description Ventilation flap and roof vent hood for horizontal mounting on flat roofs. The hood is composed of a base and a removable cover. The base is adapted to the ventilation flap where both elements are connected. The hood guarantees absolute rain protection - even in opened position of the flap. The ventilation and smoke extraction are assured in case of high wind speeds regardless of the weather and wind direction. Characteristics Ventilation flap JK-180 HV or JK-180 HV-dB (see specifications of JK-180 HV/JK-180 HV-dB) Flat roof base with connection interface for the ventilation flap Flexible mounting of the flap: flush-mounted from inside the shaft or inside of the base Integration to thermal insulation Weather protection Condensate recovery gutter and outlet nozzle Eased maintenance thanks to the good accessibility when removing the cover Bird protection grille inside the hood s: spring return or low-noise direct current motor (ref....-db...); roof vent hood made of galvanized steel (Ref....-S) or aluminium (ref....-a) Optimal protection under all weather conditions Base and cover available in numerous RAL colours Technical specification The mounting of the roof vent can easily be done by a roofer but should not be part of the lift professional s tasks. Depending on the installation position, the maintenance of the flap might have to occur on the roof. By way of precaution we point out that applicable accident prevention regulations must be observed. certified according to: EN Material JK-180 HVC Galvanized steel (ref....-s) Aluminium (ref....-a) Base wall thickness Base structure - 1,2 mm Flange - 2 mm Cover wall thickness Inner body - 2 mm Exterior sheet - 1,2 mm Finishing Base - spot welding Cover - riveting BlueKit ventilation flaps - September 2017

9 Roof vent JK-180 HVC Section B-B Section A-A Condensate outlet nozzle Flat roof upper layer Roof sealing Thermal insulation Concret ceiling Articles and dimensions - JK-180 HVC Designation acc. to flap opening (mm) BxH Net ventilation surface (m2) Recommended opening dimensions (mm) B1xH1 Minimal opening dimensions (mm) B1xH1* Mounting plate dimensions (mm) B2xH2 Cover dimensions B3xH3 Base height (mm) L1** Cover height (mm) L2 Overall height of the roof vent (mm) L3 Article number JK-180 HVC-S Article number JK-180 HVC-S-dB Article number JK-180 HVC-A Article number JK-180 HVC-A-dB 360x360 0,10 590x x x x x530 0,23 760x x x x x700 0,41 930x x x x x860 0, x x x x x1030 0, x x x x x1200 1, x x x x Application For installation from the roof, the flap is placed in the roof opening. The base is put on the mounting plate of the flap so that the drilling holes match and is then fixed on the ceiling with wall anchors. Finally, the weather cover is screwed on the base. Please refer to the BlueKit L-AIO installation guide for further installation details. * When using the minimal opening dimensions, demounting of the flap is necessary for the maintenance or replacement of the motor. See also JK-180 HV-dB for the minimal opening dimensions of JK-180 HVC-S-dB ** other base heights available upon request September BlueKit ventilation flaps 9

10 Roof vent with blades JK-180 HVL Description Ventilation flap and roof vent hood with blade for horizontal mounting on flat roofs. The hood is composed of a base and a removable cover. The base is adapted to the ventilation flap where both elements are connected. The hood guarantees an absolute rain protection - even in opened position of the flap. The ventilation and smoke extraction are assured in case of high wind speeds regardless of the weather and wind direction. Characteristics Ventilation flap JK-180 HV or JK-180 HV-dB (see specifications of JK-180 HV/JK-180 HV-dB) Flat roof base with connection interface for the ventilation flap Flexible mounting of the flap: flush-mounted from inside the shaft or inside of the base Integration to thermal insulation Weather protection Ideal for lack of space: the cover dimensions correspond to the base dimensions Condensate recovery gutter and outlet nozzle Eased maintenance thanks to the good accessibility when removing the cover Bird protection grille inside the hood s: spring return or low-noise direct current motor (ref....-db...); roof vent hood made of galvanized steel (Ref....-S) or aluminium (ref....-a) Compact solution for optimal insulation and protection Base and cover available in numerous RAL colours Technical specification The mounting of the roof vent can easily be done by a roofer but should not be part of the lift professional s tasks. Depending on the installation position, the maintenance of the flap might have to occur on the roof. By way of precaution we point out that applicable accident prevention regulations must be observed. certified according to: EN Material JK-180 HVL Galvanized steel (ref....-s) Aluminium (ref....-a) Base wall thickness Base structure - 1,2 mm Flange - 2 mm Cover wall thickness Inner body - 2 mm Exterior sheet - 1,2 mm Finishing Base - spot welding Cover - riveting BlueKit ventilation flaps - September 2017

11 Roof vent with blades JK-180 HVL Section B-B Section A-A Condensate outlet nozzle Flat roof upper layer Roof sealing Thermal insulation Articles and dimensions - JK-180 HVL Designation acc. to flap opening (mm) BxH Net ventilation surface (m2) Recommended opening dimensions (mm) B1xH1 Minimal opening dimensions (mm) B1xH1* Mounting plate dimensions (mm) B2xH2 Cover dimensions B3xH3 Base height (mm) L1** Cover height (mm) L2 Overall height of the roof vent (mm) L3 Article number JK-180 HVL-S Article number JK-180 HVL-S-dB Article number JK-180 HVL-A Article number JK-180 HVL-A-dB 360x360 0,10 590x x x x x530 0,23 760x x x x x700 0,41 930x x x x x860 0, x x x x x1030 0, x x x x x1200 1, x x x x Application For installation from the roof, the flap is placed in the roof opening. The base is put on the mounting plate of the flap so that the drilling holes match and is then fixed on the ceiling with wall anchors. Finally, the weather cover is screwed on the base. Please refer to the BlueKit L-AIO installation guide for further installation details. * When using the minimal opening, dimensions demounting of the flap is necessary for the maintenance or replacement of the motor. See also JK-180 HV-dB for the minimal opening dimensions of JK-180 HVL-S-dB ** other base heights available upon request September BlueKit ventilation flaps 11

12 Insulated roof vent TF (Thermo Flap) Description Thermally insulated smoke and heat exhaust ventilation (SHEV) hood for horizontal mounting on flat roofs (max. slope up to 5%). For ventilation and smoke exhaust purposes the hood is equipped with an 24V electric motor. Ready-to-install solution composed of a base in fiberglass, an integrated motor-driven louvre window with thermally separated aluminium profiles and a cover. Characteristics Integration to thermal insulation Weather protection Ready-to-install solution Fall-through-resistant Ventilation and smoke extraction through ventilation opening on 4 sides assured regardless of wind direction The insulated base in fiberglass (GRP) prevents from condensate formation Eased maintenance thanks to the good accessibility when removing the cover Insect protection grille inside the cover Excellent heat transfer coefficient: 0,41-0,55 W/m2k Ideal for lack of space: the cover dimensions correspond to the base dimensions The all-in-one solution with insulation Insect protection grille Technical specification Louvre window Base certified according to: EN Cover Power supply Torque Functional safety Run-time Sound power level TF 1,5 mm aluminium sheet on both sides 25 mm PU foam insulation inside 2,5 mm GRP layer on both sides, Foam insulation inside - Overall thickness 60 mm 0,8 mm galvanized steel sheet Direct current motor 24 VDC 10 Nm cycles ca. 4 sec. ca. 25 db BlueKit ventilation flaps - September 2017

13 Insulated roof vent TF (Thermo Flap) Section B-B Section A-A 450x450mm - 1 blade 600x600mm - 2 blades Flat roof upper layer Roof sealing Thermal Insulation 800x800mm - 3 blades Articles and dimensions - TF Designation acc. to opening dimensions (mm) BxH Net ventilation surface (m2) Base dimensions (mm) B1xH1 Cover dimensions (mm) B2xH2 Base height (mm) L1 Cover height (mm) L2 Overall height (mm) L3 U-Value (W/m2K) Number of blades Weight (kg) Article number TF 450x450 0,10 810x x , x600 0,20 960x x , x800 0, x x , Application The low weight allows a simple handling and positioning on the roof. No special substructure or mounting is required: the hood is preassembled and is fixed directly above the opening with stainless steel screws. The mounting of the roof vent can easily be done by a roofer but should not be part of the lift professional s tasks. Depending on the installation position, the maintenance of the flap might have to occur on the roof. By way of precaution we point out that applicable accident prevention regulations must be observed. September BlueKit ventilation flaps 13

14 Ventilation flap with weather protection grille JK-180 HV-ALAS Description Ventilation flap and weather protection grille allowing a flush-mounted closure of the permanent lift shaft opening. The flap is designed for a vertical and integrated installation inside the facade opening. The weather and bird protection grille can be installed from the shaft and provides the necessary weather protection on the outside wall. Characteristics Integrated flush-mounting of the ventilation flap (see specifications of JK-180 HV) Integration to thermal insulation Weather protection grille ALAS with fixed rain-repellent blades preventing the ingress of rain A supplementary grid protects against intrusion of birds Easy installation from the shaft or the machine room Mounting feet for easy attaching inside the opening s: spring return or low-noise direct current motor (ref....-db...) Vertical ventilation and protection, quite simply! Technical specification Louvres Bird protection grid Frame JK-180 HV-ALAS Galvanized steel Galvanized steel Galvanized steel Note The position of the smoke exhaust opening has to be planified in such a way that the smoke exhaust is not affected by the wind! certified according to: EN BlueKit ventilation flaps - September 2017

15 Ventilation flap with weather protection grille JK-180 HV-ALAS Mounting plate B2xH2 Opening dimensions B1xH1 Flap Frame Flap opening BxH Inside Outside Inside Outside Inside view Outside view Mounting feet dimensions Section Alternative section Weather protection grille depth (mm): 78 Ventilation flap depth (mm): 180 Minimum wall thickness (mm): 260 Articles and dimensions - JK-180 HV-ALAS Designation acc. to flap opening(mm) BxH 360x x x x x x1200 Net ventilation surface (m 2 ) 0,10 0,23 0,38 0,56 0,77 1,03 Opening dimensions (mm) B1xH1 590x x x x x x1290 Mounting plate dimensions (mm) B2xH2 740x x x x x x1440 Article number JK-180 HV-ALAS Article number JK-180 HV-ALAS-dB Other dimensions available upon request Application The weather protection grille is secured against falling with a safety line and placed diagonally through the opening to the outside. While pulling the grille against the outer wall, it is attached to the inside of the opening with the mounting feet. Finally, the ventilation flap incl. the sealing tape is placed in the opening and fixed to the inner wall through the drilling holes of the mounting plate. September BlueKit ventilation flaps 15

16 Insulated louvre windows S9-iVt-05 LF-MR and Tairmo-LF-MR Description Louvre window and mounting frame allowing a flush-mounted closure of the permanent lift shaft opening. The window is designed for a vertical and integrated installation inside the facade opening and guarantees optimal insulation thanks to excellent heat transfer coefficients. Characteristics Integrated flush-mounting Integration to thermal insulation Excellent thermal performance: low heat transfer coefficient (Ug-/Up-/Uw-value) Air permeability, water tightness and heat protection Sandwich panels (S9-iVt-05 LF-MR) or glass blade frame with triple glazing (Tairmo-LF-MR) Anti breakage Attractive architectural design in the facade Combine ventilation, energetic efficiency and modern design Tairmo-LF-MR S9-iVt-05 LF-MR Technical specification certified according to: EN Supplementary products Sealing tape expanding, used for sealing between the louvre window and shaft wall (included in the mounting set) 16 Louvres Material Power supply Torque Functional safety Run-time Sound power level S9-iVt-05 LF-MR / Tairmo-LF-MR Thermally separated aluminium profiles Sandwich panels / triple glazing Direct current motor 24 VDC 0,3 Nm... 4,5 Nm cycles (EN certification) ca. 4 sec. ca. 25 db Note The position of the smoke exhaust opening has to be planified in such a way that the smoke exhaust is not affected by the wind! BlueKit ventilation flaps - September 2017

17 Insulated louvre windows S9-iVt-05 LF-MR and Tairmo-LF-MR Outside view Outside view Inside Outside Inside Outside Section Section Mounting frame: 50 x 150 x 5mm (50 x 50 x 5 mm or 50 x 100 x 5 mm dimensions available upon request) Articles and dimensions S9-iVt-05 LF-MR Tairmo-LF-MR Designation according to the element dimensions BxH 420x x x x x x x x815 Net ventilation surface (m 2 ) 0,10 0,15 0,20 0,39 0,11 0,15 0,20 0,40 Opening dimensions (mm) B1xH1 450x x x x x x x x845 Uw-value (W/m 2 K) 2,5 2,3 2,3 2,1 1,9 1,8 1,7 1,6 Number of blades Article number Other dimensions available upon request Application The sealing tape is first placed on the wall sided edge of the mounting frame. The element is then aligned in the opening parallel to the opening edges, secured and fixed to the wall via wall anchors. September BlueKit ventilation flaps 17

18 Ventilation flap JK-190 Modernisation Description Smoke and heat exhaust ventilation (SHEV) device allowing a surface-mounted closure of the permanent lift shaft opening in existing buildings. The flap is fitted for horizontal or vertical non-integrated installation. The flap s spring return motor ensures its opening in case of power failure. Characteristics Non-integrated solution surface mounting Does not decrease the ventilation surface The additional 10 mm depth of the frame allows a wider ventilation surface (free movement of the blades and airflow increase between the blades) Can be adapted to all openings Easy ventilation flap installation and motor maintenance Louvres made of aluminum profile, streamlined and torsion-resistant Pre-assembled and pre-cabled motor Motor cabling with RJ45 connector for easy connection to BlueKit system Solution for the ventilation flap mounting in a corner with additional mounting angles (accessories) Motor with positive safety function in case of power failure The flexible solution for modernisations Spring return motor certified according to: EN Supplementary products Sealing tape expanding, used for sealing between the ventilation flap and shaft wall (included in the mounting set) 18 Technical specification JK-190 Louvres Aluminium Seals EPDM-rubber Material Profiled sheet steel, dimensionally stable Thickness 1,5 mm Spring return motor Power supply 24 VAC/DC Torque 20 Nm Functional safety cycles (EN certification) Service life emergency positions (manufacturer specifications) Run-time Closing via motor 150 sec. Opening via spring return 20 sec. Sound power level Closing via motor 40 db Opening via spring return 62 db BlueKit ventilation flaps - September 2017

19 Ventilation flap JK-190 Modernisation Section B-B Section A-A Spring return motor dimensions JK-190* Net ventilation surface (m2) Ventilation flap opening (mm) H/B ,1 0,16 0,21 0,26 0,31 0,37 0,15 0,23 0,31 0,38 0,46 0,54 0,2 0,3 0,41 0,51 0,61 0,71 0,25 0,37 0,5 0,62 0,75 0,87 0,3 0,45 0,6 0,75 0,9 1,05 0,35 0,52 0,7 0,87 1,04 1,22 * Most-used standard dimensions in grey Application The ventilation flap is used in front of the opening to mark the drilling points. After having drilled, the sealing tape is attached on the frame. The flap is then fixed to the wall through the drilling holes of the frame with wall anchors. September BlueKit ventilation flaps 19

20 Ventilation flap JK-190-dB Modernisation Description Smoke and heat exhaust ventilation (SHEV) device allowing a surface-mounted closure of the permanent lift shaft opening in existing buildings. The flap is fitted for horizontal or vertical non-integrated installation. The flap is equipped with a low-noise direct current motor. Characteristics Non-integrated solution surface mounting Does not decrease the ventilation surface The additional 10 mm depth of the frame allows a wider ventilation surface (free movement of the blades and airflow increase between the blades) Can be adapted to all openings Easy ventilation flap installation and motor maintenance Louvres made of aluminum profile, streamlined and torsion-resistant Pre-assembled and pre-cabled motor Motor cabling with RJ45 connector for easy connection to BlueKit system Solution for the ventilation flap mounting in a corner with additional mounting angles (accessories) Low-noise direct current motor Low noise level solution for mordernisations Direct current motor certified according to: EN Supplementary products Sealing tape expanding, used for sealing between the ventilation flap and shaft wall (included in the mounting set) 20 Technical specification Louvres Seals Material Thickness Power supply Torque Functional safety Run-time Sound power level JK-190-dB Aluminium EPDM-rubber Profiled sheet steel, dimensionally stable 1,5 mm Direct current motor 24 VDC 10 Nm cycles (EN certification) ca. 4 sec. ca. 25 db BlueKit ventilation flaps - September 2017

21 Ventilation flap Section B-B JK-190-dB Modernisation Section A-A Direct current motor dimensions * Most-used standard dimensions in grey JK-190-dB* Net ventilation surface (m 2 ) Ventilation flap opening (mm) H/B ,1 0,15 0,2 0,25 0,3 0, ,16 0,23 0,3 0,37 0,45 0, ,21 0,31 0,41 0,5 0,6 0, ,26 0,38 0,51 0,62 0,75 0, ,31 0,46 0,61 0,75 0,9 1, ,37 0,54 0,71 0,87 1,05 1,22 Application The ventilation flap is used in front of the opening to mark the drilling points. After having drilled, the sealing tape is attached on the frame. The flap is then fixed to the wall through the drilling holes of the frame with wall anchors. September BlueKit ventilation flaps 21

22 Accessories JK ceiling/corner Modernisation Description Mounting angles - Accessories for horizontal mounting of JK-190 and JK-190-dB Characteristics Ventilation flap JK-190 with mounting angles Solution for the ventilation flap mounting in a corner of the shaft ceiling when space for fixing is not sufficient Flexible mounting according to the access to the ventilation opening Application Fixing of angle corner (1) to the ventilation flap together with the supplied nuts Positioning of the ventilation flap including mounting angle (1) in front of the opening and screw mounting in the shaft slab Positioning of mounting angle (2) on the ventilation flap and screw mounting in the shaft wall 22 BlueKit ventilation flaps - September 2017

23 Accessories JK ceiling/corner Modernisation Section B-B Drawings and dimensions with mounting angles Section A-A Ceiling corner view 1 2 September BlueKit ventilation flaps 23

24 FURTHER INFORMATION Subject to technical changes. No responsibility is accepted for the accuracy of provided information. BK-Factory will not assume any responsibility for their use INNOVATION SAFETY EFFICIENCY EN_BLUEKIT_VENTILATIONFLAPS_