4100 SERIES. Specifications: Applications:

Transcription

1 400 ERIE pecifications: Widths up to 2 (05) engths up to 6 (,829) The (25) diameter drive pulley. oad capacity up to 80 lbs.* (6kg). elt speeds to 255 ft./min. (78 M/min.). pplications: Metal Forming Metal tamping Machined Part andling 28

2 INDEX 400 ERIE INDEX Flat elt End Drive... 0 Profiles elting Mounting Packages s upport tands... ccessories Performance Charts / Data

3 400 ERIE: FT ET END DRIVE pplications: Metal Forming, tamping Machined Part andling Note: 400 mounting packages are available with metric fasteners only. pecifications:.75 (9) minimum, 2 (05) maximum belt widths. 2 () minimum, 6 (,829) maximum conveyor lengths. 2 - gauge roll formed steel frame..5 (8) bottom of frame to top of belt. The (25) diameter drive pulley turns approximately.4 (86) of belt per revolution. oad capacity up to 80 lbs.* (6kg). elt speeds to 255 ft./min. (78 M/min.). E fasteners only, metric fasteners not available on the conveyor. Do not index or reverse.75 (9) and.75 (44) wide conveyors. Features/enefits: Mild steel -piece frame with.25 (6) thick bed plate for strength and durability. Durable baked enamel finish. ow maintenance fixed pulley centers with no belt tracking requirements. Magnetic models available. Wide variety of profiles and accessories. Durable.25 (6) thick bottom wiper removes debris from belt. elt type and materials to match application requirements. * Conveyor load capacity depends on conveyor size, incline, motor position, accumulated loads and other factors. ee Performance Charts / Data section for details. 0 Order gearmotor mounting packages and gearmotorsseparately; see pages 45 & 52. For support stands and accessories, see pages & 65

4 Flow Toward ottom Wiper W W +.50 ().00 (76) 6.00 (52) W. TYP. () 0.9 (2).50 (8) 0.62 (6).28 () 0.66 (7).8 Internal ex roach -0 ow ide Profile OPTION KEYOE OT - Compatible with quick disconnect mounting block, see page 6 W = Conveyor elt Width TNDRD IZE Conveyor Width Reference Conveyor elt Width (W).75 (9).75 (44) 2.75 (70).75 (95) 6 (52) 8 (20) Conveyor ength Reference 02 0 increments up to Conveyor ength () 2 () increments up to.. 6 (,829) 2 (05) ORDERING INFORMTION /02 Drive haft Position elt. ee pages 42 Conveyor Profile. ee page 4 ex roach ocation:,,c or D Conveyor ength Reference Conveyor Width Reference 00 = ingle End Wiper, DW = Double End Wiper 400 eries Conveyor Example: /02 : 400 eries End Drive Conveyor 2 (44) wide x (94) long with hex broach located in the position, high side profile and general purpose belt. C D ince belts are being pulled, positions & D are preferred. Pushing belts ( & C) reduce conveyor load capacity by approximately 66%. ex to Round dapter.8 (0).9 (49).5" (2mm) Ø 4 x 4 x 22mm Keyway ORDERING INFORMTION: ex to Round dapter Conveyor Width Reference: 0 =.75 (9) wide (.5 diameter only) 02 =.75 (44) wide 0 = 2.75 (70) wide 04 =.75 (95) to 2 (05) wide haft Diameter: 8 =.5, 48 = 2mm 400 eries Conveyor Example: /02 : 400 eries hex to round adapter for.75 (44) side conveyor,.5 diameter shaft. Note: Dimensions are represented in inches, feet, and (millimeters). Due to the wide variety of drive set-ups and applications, point of installation guarding is the responsibility of the end user.

5 400 & 6200 ERIE: PROFIE 400 eries Profiles W +.50 ().50 (8) W 2.00 (5) W 2.06 (52) W -.62 (6) -0 ow ide -02 igh ide -0* ide Wiper 2.06 (52) W +.62 (6) W -.40 (0) 2.00 (5) W -.22 (6) -07* ow ide To ide Wiper -09 ow ide To igh ide * = Do not use with igh Friction elts W = Conveyor elt Width ORDERING INFORMTION Example: /02 : 400 eries End Drive Conveyor 2 (44) wide x (94) long with hex broach located in the position, high side profile and general purpose belt. Dimensions are represented in inches, and (millimeters). Due to the wide variety of drive set-ups and applications, point of installation guarding is the responsibility of the end user. 40

6 400 & 6200 ERIE: TNDRD ETING tandard elt election Guide tandard belt material is stocked at Dorner, then cut & spliced at the factory for fast conveyor shipment. elt - Finger plice elt - Plastic Clipper elt - Metal Clipper elt pecifications Thickness urface Material Carcass Material Maximum Part Temp. Coefficient of Friction FD pproved nti-tatic tatic Conductive Chemical Resistant pecial Characteristics or pplications 0 FD ccumulation.06 (.6) Urethane Polyester 76 F (80 C) ow x x Good Packaging, clean room & inspection General Purpose.07 (.8) Urethane Polyester 22 F (00 C) Med x x Good Most versatile belt offering 0 FD igh Friction.06 (.6) Urethane Polyester 76 F (80 C) igh x x Good Packaging, clean room & inspection ccumulation.047 (.2) Urethane Polyester 22 F (00 C) V-ow x x Good ccumulation of products 06 6 Electrically Conductive.06 (.6) Urethane Polyester 20 F (0 C) ow x x Good Electronics andling igh Friction.08 (2.) PVC Polyester 58 F (70 C) V-igh x Poor Conveys up to 5 inclines* Note: ee below for splice details. Plastic Clipper splice requires longer lead times. No Metal Clipper plice on belts over 2 (05) wide. *Incline varies due to factors like dust, fluids and part material. elt plicing Finger plice ll belts are available with a standard Thermoformed finger splice. This splice makes the belt continuous and is virtually undetectable. plice bonding methods vary by belt type. Consult factory for details. 42 Plastic Clipper* n optional plastic clipper splice is available for quick removal of belts or when conveyors are installed in tight spaces. The clipper does not protrude above the belt surface. Metal Clipper* n optional metal clipper splice is also available for quick removal of belts or when conveyors are installed in tight spaces. *ee belt charts for compatibility. Not for use with 400 ereis, 6200 eries Gang Drive or 6200 ereis with bottom wiper.

7 PECITY ETING pecialty elt election Guide pecialty belt material is not stocked at Dorner and needs to be custom ordered for your special conveyor needs. elt with Finger plice elt with Plastic Clipper elt with Metal Clipper 400 eries 6200 eries elt pecifications elt Thickness urface Material Maximum Part Temp. Coefficient of Friction FD pproved Chemical Resistance pecial Characteristics or pplications 50 X eat Resistant.05 (.) ilicone 56 F (80 C) ow Good 5 X Translucent & Nosebar, ccumulation.02 (.5) Urethane 22 F (00 C) V-ow x Good ack it inspection & Very mall Product Transfer 54 F4 4F X X FD ealed Edge.06 (.5) Urethane 76 F (80 C) ow x Good Packaging, clean room & inspection 55 F5 5F X X FD ealed Edge.06 (.5) Urethane 76 F (80 C) igh x Good Packaging, clean room & inspection 56 6F X X Cut Resistant.08 (2.) Urethane 22 F (00 C) Med. Good Oily product release, Metal stamping 57 7F X X Cut Resistant.0 (2.5) Nitrile 76 F (80 C) Med. Poor Felt-like, dry metal stamping, glass & ceramic 58 8F X Cut Resistant.06 (.5) Urethane 76 F (80 C) ow V-Good Cross-linked surface, Gold colored 59 F9 9F X X Color Contrasting.06 (.5) PVC 58 F (70 C) Med. Poor lack colored, hides overspray from ink jet G0 0G X X Color Contrasting.06 (.6) Urethane 76 F (80 C) ow x Good Green colored 6 G G X X Color Contrasting.05 (.2) Urethane 22 F (00 C) Med. x Good lue colored 6 G X X Electrically Conductive.05 (.2) Urethane 40 F ( C) ow Good tatic conductive, electronics handling 64 4G X igh Friction.7 (4.4) PVC 94 F (90 C) V-igh Poor Dark Green colored, rough top surface, product cushioning, incline / decline apps 65 5G X Chemical Resistant.05 (.) Polypropylene 250 F (26 C) ow x V-Good V-Good Cut resistance, excellent product release 66 6G X X Chemical Resistant.07 (.7) Polyester 22 F (00 C) Med. x V-Good Good Cut resistance, metal stamping apps 67 7G X ow Friction Cleated.06 (.6) Polyester 22 F (00 C) n/a x Good Note: Plastic Clipper splice requires longer lead times. No Metal Clipper plice on belts over 2 (05) wide. * Do not use with PZ conveyor. ** 2 (05) wide conveyor maximum. *** Not available in 2 (5) wide. 24 () wide conveyor maximum Excellent product release, consult factory for part number and how to specify low friction ORDERING INFORMTION: tandard Flat & pecialty elt Example: 220M : 2200 eries End Drive Conveyor, 2 (5) wide x (94) long with output shaft located in the position, standard low sides, general purpose belt and English documentation. 4

8 GERMOTOR MOUNTING PCKGE Mounting Package & election teps tep : elect a Mounting Package. For End drive conveyors, select a side, bottom, top or gang drive mount (pages 46-49). If a Center Drive conveyor is being outfitted, refer to the Center Drive section pages 50 & 5. e sure to note if it is for a 90 or Parallel haft. tep 2: Using elt peed & oad Requirements, determine the required (ight, eavy or tandard) for your application using the chart below. tep : Find the appropriate set of elt peed Charts (pages 48 & 5) for the Mounting Package you selected and choose between the Fixed or Variable peed chart. tep 4: Go down the first column of the elt peed Chart and locate the required elt peed for your application. If the desired belt speed is not listed, round up to the next higher speed. (Dorner offers much more than just the belt speeds listed in the tables, contact the factory for complete details) tep 5: From the row containing your required elt peed, check to be sure that speed is available for the Mount Package you chose. (End Drive Only - Top, ottom or ide) tep 6: Use the Drive / Driven Pulley Kit combination to complete your Mounting Package tep 7: Note the RPM from, it will be needed to select the correct from the Chart. tep 8: Reference the Chart # to locate a compatible Chart on Pages e sure to select a Chart to match your (ight, tandard or eavy) and your Mounting Package while meeting your electrical requirements. (Red = Parallel haft or lue = 90 ) tep 9: Using the RPM from (tep 6), locate the for your from the Table. elt peed - Ft/min (M/min) GERMOTOR TYPE ight oad tandard oad eavy oad 0-5 (0-4.6) 6-0 (4.9-9.) -45 (9.5-.7) 46- (4-8.) 6-75 ( ) ( ) 9-0 ( ) -0 (.8-9.6) -50 ( ) 5-75 (46-5.4) (5.7-6) ( ) ( ) ( ) Conveyor oad - bs (Kg) 0 (4.5) 20 (9.) 0 (.6) 40 (8.2) 50 (22.7) (27.) 70 (.8) 80 (6.4) 90 (40.9) 00 (45.5) 0 (50) 20 (54.5) ORDERING INFORMTION: End Drive Mounting Packages 6 M P Drive / Driven Pulley Combination: ee elt peed charts, Pages 48 & 5 (Top and ottom mounts only) elt tyle: - = Flat elt or add Cleat :,, C, F, G,, J, V Mounting Position:,, C, D. Conveyor Width Reference: ee Conveyor ection. : ee charts, Page 52-57, V,, Output haft: ee charts, Page P = Parallel haft or = 90 Mount tyle: = ide Mount, = ottom Mount, T = Top Mount Documentation anguage: M = English, G = CE German, U = CE English Conveyor eries: Example: 6MP = 400 End Drive 6 = 6200 End Drive (non-gang Drive) Drive haft Position ince belts are being pulled, positions & D are preferred. Pushing belts ( & C) reduce conveyor load capacity by approximately 66%. : ottom mount package with English documentation for 6 (52) wide 6200 series end drive conveyor. Configured for a parallel shaft, tandard load motor in the mount position with a 28:28 drive / driven pulley combination. 45

9 400 & 6200 ERIE: END DRIVE MOUNTING PCKGE ide Mount Package, (72) 9.2 (24) 5.2 (2) W 2.2 (56) 4. (62) 5. ().6 (4) tandard load gearmotors only Includes : mounting bracket, coupling, coupling guard & mounting hardware W = Conveyor elt Width ottom Mount Package, (52) 0. (8) W 0.7 (7) 9.2 (24) : tandard oad Flat elt = 5.2 (2) : tandard oad Flat elt = 4.6 (7) tandard oad Cleated elt = 7.9 (99) tandard oad Cleated elt = 4.6 (7) eavy oad Flat elt = 7.9 (99) eavy oad Flat elt = 5.6 (95) eavy oad Cleated elt = 7.9 (99) eavy oad Cleated elt = 5.6 (95) Includes : mounting bracket, coupling, coupling guard & mounting hardware W = Conveyor elt Width.4 (87) 4.5 (5) 0.7 (7) Top Mount Package, 90.4 (87) 2.0(52) C 0.(8).8(46) 4.5 (5) W 0.7(7) : tandard oad =.8 (96) : tandard oad = 4.6 (7) C: tandard oad =. (28) eavy oad =.4 (86) eavy oad = 5.6 (95) eavy oad =.8 (0) Includes : mounting bracket, coupling, coupling guard & mounting hardware W = Conveyor elt Width 90 tandard oad ocation Options Notes: Position recommended. Vertical positions 2 & 4 may require additional stabilizing bracket. Consult factory for details ee pages for election 46 Note: Conveyor and gearmotor are not included in the mounting package and must be ordered separately. Dimensions are represented in inches and (millimeters)

10 END DRIVE MOUNTING PCKGE ide Mount Package, Parallel haft 2. (52).2 (8) W.7 (44) 6. (55).2 (8) 0.6 (5) : ight oad, Fixed peed = 4.6 (7) ight oad, Variable peed = 6.7 (70) ight oad CE Fixed peed = 7.2 (8) ight load gearmotors only Includes : mounting bracket, coupling, coupling guard & mounting hardware W = Conveyor elt Width ottom Mount Package, Parallel haft 2. (59) W 0.6 (6).7 (94) 6.4 (6) D 2.6 (67) C 0.6 (6) : ight oad Flat elt = 6.9 (75) C: ight oad Flat elt = 6.7 (70) ight oad Cleated elt = 8.9 (226) ight oad Cleated elt = 6.7 (70) tandard oad Flat elt = 9.2 (24) tandard oad Flat elt = (267) tandard oad Cleated elt = 9.2 (24) tandard oad Cleated elt = (267) : ight oad Flat elt = 6.2 (58) D: ight oad Flat elt = 6. (55) ight oad Cleated elt = 8. (2) ight oad Cleated elt = 5.6 (42) tandard oad Flat elt = 8.5 (26) tandard oad Flat elt = 4.6 (6) tandard oad Cleated elt = 0. (262) tandard oad Cleated elt = 4.6 (6) Includes : mounting bracket, coupling, coupling guard & mounting hardware W = Conveyor elt Width Top Mount Package, Parallel haft 2.6 (67) C 2. (59) W.8 (46) 6. (55) D 0.6 (6) : ight oad = 8.9 (226) C: ight oad = 6.7 (70) tandard oad = 9.2 (24) tandard oad = (267) : ight oad =. (84) D: ight oad = 5.6 (42) tandard oad = 4. (0) tandard oad = 4.6 (6) Includes : mounting bracket, coupling, coupling guard & mounting hardware W = Conveyor elt Width 47

11 400 & 6200 ERIE: END & GNG DRIVE ET PEED CRT Refer to the election teps on Page 45 for instructions on using the elt peed Charts. Fixed peed elt peed Ft/min M/min RPM From Mount Package Pulley Kit Chart # Top & ottom ide Drive Pulley Driven Pulley ight oad tandard oad X X X eavy oad X 9 2 4, 5 2, X X , 5 2, X X X X X , X , 5 2, X X , X X X , 5 2, X X X , 5 2, X X X , 5 2, X , 5 2, X , 5 2, X X , 5 2, X , 5 2, X , 5 2, X , 5 2, X , 5 2, X , 5 2, RPM at 50 z 5.5 2* X * X X * X X * X * X * X X * X * X X * X X * X * X X * X * X * X * X * X * X 22 6 Variable peed elt peed Ft/min M/min RPM From Mount Package Pulley Kit Chart # Top & ottom ide Drive Pulley Driven Pulley ight oad tandard oad X X eavy oad X 9 2 8, 5, X , 5, X X , X , X X X X X , 5, X X , X X X , 5, X X X , X , 5, X , 5, X , X X , X , 5, X , 0 4 RPM from CE/50 z gearmotors VFD drive at 6 Max. z. output * X * X X * X X * X X * X X * X * X X * X * X Note: Red = Parallel haft, lue = 90 48

12 GNG DRIVE MOUNTING PCKGE.50 (8) olster Plate.88 (5).25 (2).8 (86) MIN. Gang Drive Pulleys require periodic greasing 50.0 (,270) MX..9 (2) Includes: Motor mounting bracket, 4 (29mm) hex shaft, coupling, shaft guard, support block, and support block bracket. - Components included with single output shaft assembly. - dditional components included with double output shaft assembly. ORDERING INFORMTION Notes: Conveyors cannot be secured to bolster plate Order conveyor with gang drive option separately Order gearmotor separately (90 tandard & eavy oad only) Positions 2 & recommended 6 M 0 0 = ingle Output haft 0 = Double Output haft Documentation anguage M = English, U = CE English Example: 6M0 : Gang drive mounting package with English documentation. Common Drive et-up Includes mounting structure, drive shaft, shaft guard and conveyor mounting hardware. Order gearmotor & gearmotor mounting package separately Consult factory with conveyor and spacing details Conveyors are secured to sub-structure at fixed centerline locations Common drive setups can be customized to your exact specifications. Just provide the conveyor widths, lengths, quantity and centerline spacing. vailable with top, bottom or side mount packages for standard or heavy load gearmotors. Consult factory with details. Due to the wide variety of possible conveyor setups, adaption of the supplied guarding material is the responsibility of the end user. 49

13 400 & 6200 ERIE: GERMOTOR election teps Refer to page 45 for directions on electing a Mounting Package and. GERMOTOR TYPE ight oad tandard oad eavy oad Conveyor oad - bs (Kg) 0 (4.5) 20 (9.) 0 (.6) 40 (8.2) 50 (22.7) (27.) 70 (.8) 80 (6.4) 90 (40.9) 00 (45.5) 0 (50) 20 (54.5) elt peed - Ft/min (M/min) 0-5 (0-4.6) 6-0 (4.9-9.) -45 (9.5-.7) 46- (4-8.) 6-75 ( ) ( ) 9-0 ( ) -0 (.8-9.6) -50 ( ) 5-75 (46-5.4) (5.7-6) ( ) ( ) ( ) ccessories 90 eat ink 5.4 (8) 5.25 () 2.80 (7) Reduces gear head surface temperature by up to 50 F (0 C) Compatible with tandard and eavy oad 90 s lack anodized aluminum eat ink 52

14 GERMOTOR ight oad, Fixed peed Chart Parallel haft ealed Totally enclosed, Non-ventilated. Includes witch, Cord & Overload Protection 5V, Phase Non-reversing z 5.4 (8).5 (80) 2.89 (7).5 (80).9 (2).8 Ø 6.92 (76) 6.05 (54).26 (2) 5.87 (49).05 (27) RPM Ph p Ph Kw Ph F in-lbs N-m 62M06P4F(N) 62M05P4F(N) (n) = Reversing capability. N = No reversing switch. R = With reversing switch Chart 2 Parallel haft Totally enclosed, Fan Cooled IP44 Protection Rating Non-reversing 50 z Order starter separately, ee page () 2.5 (6) 2 mm Ø 8.8 (224).0 (25).2 (80) RPM Ph Kw Ph F Ph Kw Ph F N-m tarter Chart 62Z028P42FN 62Z028P4(vp)FN 62Z008P42FN 62Z008P4(vp)FN (vp) = Voltage and Phase 2 = 20V, phase 4 = 400V, phase n/a n/a 0. n/a 0. n/a n/a n/a n/a.22/. n/a.22/ Note: When buying a gearmotor only without the starter, the customer must supply their own on/off switch and motor overload protection to comply with the CE afety Directive. ight oad, Variable peed Chart Parallel haft 0 Volts DC ealed Totally enclosed, Non-ventilated RPM motor Order controller separately, ee page 58.7 (4).4 (86).4 (86).0 (25).5 Ø 9.4 (28).6 (40) 2.9 (7) 2.4 (6) RPM p Kw F in-lbs N-m Vari - peed Control Chart 62M0PDDEN 62M08PDDEN 42 9 V V F = Full oad mperes Note: 8 (20 ) and wider conveyors with light load drives should be limited to 8 (2,48) long. ome motors & gear reducers may normally operate hot to the touch. Consult factory for specific operating temperatures. 5

15 400 & 6200 ERIE: GERMOTOR tandard oad, Fixed peed Chart 4 90 ealed NEM 42 CZ C Face Totally enclosed, Fan cooled 5V phase includes switch, Cord & Overload protection /4V phase wiring by others z Order phase starter separately, ee page (64).4 (5) 6.6 (68) 2.8 (70) 5.2 () 2.2 (56) 2.9 (74). (4) 4. (62) 5. () 5. () RPM Ph p Ph Kw Ph F Ph p Ph Kw Ph F in-lbs N-m Phase tarter Chart 2M04(vp)F(n) 2M0404(vp)F(n) 2M0204(vp)F(n) 2M004(vp)F(n) 2M0054(vp)F(n) (vp) = Voltage and Phase (n) = Reversing Capability = 5V, phase N = No reversing switch. 2 = / 4V, phase R = With reversing switch (5V, phase only) /0.6.2/0.6.2/0.6.2/0.6.2/ Chart 5 Parallel haft ealed s Totally enclosed, Fan cooled 5V phase includes switch, Cord & Overload protection 20V phase wiring by others z Order phase starter separately, ee page (8) 4.75 (2) 2.9 (6) 2.04 (52) 6.7 (7) 2.62 (67).75 Ø 2.00 (5).00 (28) 4.75 (2) 62M80P4(vp)F(n) 62M0P4(vp)F(n) 62M00P4(vp)F(n) 62M020P4(vp)F(n) 62M00P4(vp)F(n) 62M005P4(vp)F(n) RPM Phase Phase p Kw F in-lbs p Kw F in-lbs (vp) = Voltage and Phase (n) = Reversing Capability = 5V, phase N = No reversing switch. 2 = 20V, phase R = With reversing switch (5V, phase only) N-m Phase tarter Chart M M M M Chart 6 90 ealed IEC 6 5 C Face IP 55 Protection Rating Totally enclosed, Fan cooled Non-reversing 50 z Order starter separately, ee page 59 RPM 62Z04(vp)FN 62Z0404(vp)FN 62Z0204(vp)FN 62Z004(vp)FN 62Z0054(vp)FN (vp) = Voltage and Phase 2 = 20V, phase 2 = 20,, phase 4 = 400V, phase Ph Kw (44) 6.6 (68) 5.5 (40) Ph F (70) 4.9 (24) 2.9 (74).4 (5) Ph Kw (56). (4) Ph F.4/.8.4/.8.4/.8.4/.8.4/.8.4 (9) 5.9 (49) N-m tarter Chart Note: When buying a gearmotor only without the starter, the customer must supply their own on/off switch and motor overload protection to comply with the CE afety Directive. I I I I I 54 F = Full oad mperes ome motors & gear reducers may normally operate hot to the touch. Consult factory for specific operating temperatures.

16 GERMOTOR tandard oad, Variable peed Chart Volts DC ealed NEM 42 CZ C Face Totally enclosed, Fan cooled RPM motor Order controller separately, ee page 58 RPM p Kw F in-lbs N-m Vari - peed Control Chart 22M0DDEN 22M040DDEN 22M020DDEN 22M00DDEN 22M005DDEN Chart 8 90 Variable frequency Drive, 6 - z ealed NEM 56C C Face Totally enclosed, Fan cooled 20/4 Volts, phase Order controller separately, ee page (68).4 (5) 6.6 (68) 7.6 (94) 2.9 (74) 2.2 (56). (4) 5.9 (49) 2.9 (27) RPM p Kw F in-lbs N-m Vari - peed Control Chart 2M042EN 2M04042EN 2M02042EN 2M0042EN 2M00542EN * = t z /.97.6 /.97.6 /.97.6 /.97.6 / Chart 9 90 Variable Frequency Drive, 25-6 z ealed IEC 6 5 C Face IP 55 Protection Rating Totally enclosed, Fan cooled 20V, phase Order controller separately, ee page 58 RPM* 62Z042EN 62Z04042EN 62Z02042EN 62Z0042EN 62Z00542EN * = t 50 z Ph Kw Ph F N-m* Vari - peed Note: When buying a gearmotor only without the starter, the customer must supply their own on/off switch and motor overload protection to comply with the CE afety Directive. ome motors & gear reducers may normally operate hot to the touch. Consult factory for specific operating temperatures. F = Full oad mperes 55

17 400 & 6200 ERIE: GERMOTOR tandard oad, Variable peed Chart 0 Parallel haft 0 Volts DC ealed Totally enclosed, Non-ventilated RPM motor Order controller separately, ee page (62) 4.9 (24).5 (7) 4.8 (2).75 Ø 2.5 (8) 2.0 (5) 4. (08) RPM p Kw F in-lbs N-m Vari - peed Control Chart 62M80PDDEN 62M0PDDEN 62M00PDDEN 62M020PDDEN 62M00PDDEN 62M005PDDEN Chart Parallel haft Variable frequency drive, 0 to z ealed Totally enclosed, Fan cooled 20 Volts / Phase, VFD duty Order controller separately, ee page (8) 4.75 (2) 2.9 (6) 2.04 (52) 6.7 (7) 2.62 (67).75 Ø 2.00 (5).00 (28) 4.75 (2) *RPM p Kw F in-lbs N-m Vari - peed Control Chart 62M80P42EN 62M0P42EN 62M00P42EN 62M020P42EN 62M00P42EN 62M005P42EN * = t z eavy oad, Fixed peed Chart 2 90 ealed NEM 56 C Face Totally enclosed, Fan cooled 5V phase includes switch, Cord & Overload protection /4V phase wiring by others z Order phase starter separately, ee page 59.4 (5) 7.7 (96) 7.7 (96) 6.6 (68) 2.8 (70) 6.6 (68) 2.2 (56) 2.9. (74) (4) 5.9 (49) 5.2 (86) 6.2 (57) RPM Ph p Ph Kw Ph F Ph p Ph Kw Ph F in-lbs N-m Phase tarter Chart 2M04(vp)F(n) 2M0404(vp)F(n) 2M0204(vp)F(n) 2M004(vp)F(n) 2M0054(vp)F(n) (vp) = Voltage and Phase (n) = Reversing Capability = 5V, phase N = No reversing switch. 2 = / 4V, phase R = With reversing switch (5V, phase only) / 2.-2/ 2.-2/ 2.-2/ 2.-2/ M M M M M 56 F = Full oad mperes ome motors & gear reducers may normally operate hot to the touch. Consult factory for specific operating temperatures.

18 GERMOTOR eavy oad, Fixed peed Chart 90 ir ealed Nema 56 C Face Non-reversing Includes muffler, filter, regulator & lubricator Use with standard load mounting package 62M0000FN 62M040000FN 62M020000FN 62M020000FN 62M005000FN RPM** (68). (84).4 (5) P* in-lbs ** N-m** (68) 2.2 (56) 2.9 (74). (4) (267) 5.9 (49) 6.5 (65) * = t 40 PI (2,8 bar) line pressure ** = t 725 RPM from motor, 25 CFM eavy oad, Variable peed Chart V DC ealed NEM 56 C Face Totally enclosed, Fan cooled RPM motor Order controller separately, ee page 58 2M0D9DEN 2M040D9DEN 2M020D9DEN 62M00D9DEN 62M005D9DEN RPM p Kw F in-lbs N-m (68).4 (5) (95) 6.6 (68) 2.6 (67) (56) 6.6 (68) 2.9 (74) 5.9 (49). (4) (72) 5.2 () Vari - peed Control Chart C C C C C Chart 5 90 Variable Frequency Drive, 6 - z ealed NEM 56 C Face Totally enclosed, Non-ventilated 20/4 Volts, Phase Order controller separately, ee page 58 RPM* 2M042EN 2M04042EN 2M02042EN 2M0042EN 2M00542EN Ph p Ph Kw (68) 7.9 (20) 6.6 (68) Ph F.6/.8.6/.8.6/.8.6/.8.6/.8.4 (5). (79) in-lbs* (74) 2.2 (56). (4) 5.9 (49) N-m* (65) 6. (55) Vari - peed Control Chart * t z Chart 6 90 Integrated motor control Variable frequency drive, 0 to 80 z Digital display with start/stop and forward/reverse keypad NEM 56 C face sealed gearmotor Totally enclosed, Fan cooled 5/20 Volts, Phase input voltage 9. (22) 8.5 (27) 7. (80).4 (5) 2.9 (7) 2.2 (56) 2.9 (74) 5.9 (49). (4) 5.8 (40) 7. (80) 2M04EC 2M0404EC 2M0204EC 2M004EC 2M0054EC RPM* p Kw Controller mps 2.4/ / / / /6.2 in-lbs* N-m* * t z F = Full oad mperes 57

19 400 & 6200 ERIE: VRIE PEED CONTROER Variable peed Controllers Chart PWM DC control Nema enclosure ine cord & Motor cord On / Off switch for 62MD4 Forward / Off / Reverse switch for 62MD4R peed potentiometer Mounting hardware Input Volts Input Phase Input z Output Volts *Max mps Reversing 62MD4 62MD4R (8) 5. () 62MD4 4.5 (4) 4.6 (6).9 (00) 0VDC 0VDC 7. (80) 5. (5) 62MD4R (47) 5.7 (45) No 5.0 (27) Chart VFD control IP 65 enclosure EMC filter peed potentiometer Mounting hardware ine cord & motor cord 8.2 (208) 62(c)V (47) 5. (0) 5.8 (46) 0.8 (27) 2.8 (72) 62ZV222C 4.7 (9) 5. (0) VFD control Chassis mount EMC filter Wiring by others Input Volts Input Phase Input z Output Volts Out Phase *Max Kw Max mps Reversing 62(c)V222 62ZV222C (c) = Electrical Configuration F = CE French Chart C PWM DC control NEM enclosure ine cord & Motor cord On / Off switch for 62MD92 & 62MD9 Forward / Off / Reverse switch for 62MD92R & 62MD9R peed potentiometer *ee F from motor charts Mounting hardware Input Volts Input Phase Input z Output Volts *Max mps Reversing 62MD92 62MD92R 62MD9 62MD9R G = CE German U = CE Great ritain VDC 90VDC 90VDC 90VDC Note:When buying a chassis mount control, the customer must provide wiring that complies with Ce afety Directives. 62MD92 & 62MD92R MD9 & 62MD9R No No Chart D Full feature VFD control NEM 4 enclosure Digital display Keypad with tart / top, Forward / Reverse and speed variations Includes cord to motor Power to controller by others 62MV22 includes line cord to controller Mounting hardware +.0 (25) 8.9 (226) 7.9 (200) +.2 (5) *eeffrommotorcharts Input Volts Input Phase Input z Output Volts Output Phase Max p *Output mps Reverse Width Depth 58 62MV22 62MV222 62MV2 62MV22 62MV227 62MV222 62MV227 62MV44 62MV (55) 6. (55) 6. (55) 6. (55) 6. (55) 4.7 (9) 6. (55) 4.7 (9) 6. (55).8 (96).8 (96) 4.4 (2) 4.4 (2) 5. (4).8 (96) 5. (4).8 (96) 4.4 (2)

20 MNU MOTOR TRTER Variable peed Controllers Chart E VFD control Nema enclosure ine cord and Motor cord On / Off switch peed potentiometer Mounting hardware Forward / Reverse switch Input Volts Input Phase Input z Output Volts Output Phase Max p *Max mps Reversing 62MV22 62MV22R No Manual Motor tarters Manual motor starts are manual electrical disconnects that provide motor overload protection and are required by the National Electric Code (NEC) for safe motor operation. Illustration Illustration IP 55 Enclosure Push buton tart / top Includes mounting hardware 7.0 (78).4 (86).7 (94) 7.0 (78).4 (86).7 (94) Chart 20V, phase includes cord, plug & starter. 20/400V, phase wiring to starter by others. Wiring between motor & starter provided when ordered together. 50 z In Volts In Phase mp Range Illustration 62(c)M2 62(c)M2 62(c)M Chart I 20V, phase includes cord, plug & starter. 20/400V, phase wiring to starter by others. Wiring between motor & starter provided when ordered together. 50 z In Volts In Phase mp Range Illustration 62(c)M2T 62(c)M2T 62(c)M4T Note: When buying a gearmotor only without the starter, the customer must supply their own on/off switch and motor overload protection to comply with NEC and CE safety directives. (c) = Electrical Configuration F = CE French G = CE German U = CE Great ritain Chart 20/4V, phase wiring to starter by others. Wiring between motor & starter provided when ordered together. z In Volts In Phase mp Range Illustration 62MM2 62MM Chart M 20/4V, phase wiring to starter by others. Wiring between motor & starter provided when ordered together. z In Volts In Phase mp Range Illustration 62MM2M 62MM4M

21 400 & 6200 ERIE: UPPORT TND Quantity Charts upport tand Quantity Chart Conveyor ength Number of upports 2 () - 4 (29) * 2 () - 6 (829) 2 7 (24) - 2 (658) (962) - 8 (5486) 4 9 (579) - 24 (75) 5 *End Drive Conveyors with ingle-post upport tands only. Requires the use of diagonal bracing, see page 64. eavy load gearmotors require a minimum of 2 stands to support conveyor and gearmotor package. Required Return Roller Quantity Chart max feet between return rollers Conveyor Width Flat elt Cleated elt Quanity of return rollers required = whole number result of : conveyor length in feet max distance between return rollers Example : 6200 flat belt 8 wide x 4 long = return rollers required 6200 eries Return Rollers Cleated elt Return Roller 2.25 (57) Flat elt Return Roller for 2 to 6 Wide Conveyors.25 (2) W+.96 (24).78 (20).75 (9) Return Roller for 2200 eries, Cleated elt W+.96 (24).78 (20).75 (9) Return Roller for 2200 eries 2 (44) - 6 (52) wide Flat elt conveyors Flat elt Return Roller for 8 to 48 Wide Conveyors.25 (2) ORDERING INFORMTION 4949 WW W+.96 (24).78 (20).75 (9) Conveyor width reference: 08 to 48 in 02 increments Conveyor reference: 4949 = 6200 eries Example: : Return Roller for a 2 (05) flat belt conveyor.

22 UPPORT TND 6200 eries Mounting rackets Cleated tand Mounting racket 6.65 (69) Flat elt tand Mounting racket.00 (76).47 (88).47 (88) M6-.0 W-.6 (4) 2.25 (57) M6-.0 W-.6 (4) 2.25 (57) tand Mounting racket, Cleated elt Conveyor tand Mounting racket,flat elt Conveyor Note: Conveyors can be ordered with the required number of mounting brackets. If desired, order additional mounting brackets separately. 400 eries Mounting rackets Flow toward bottom wiper lock 2.0 (76).75 (9) lock Mounting lock Kits are used to mount the conveyor to support stands. Kit includes: mounting block, keyhole slots in conveyor frame, and mounting fasteners W /4-20 Drilled & Tapped Keyhole lots allow accessories or mounting blocks to be attached directly to the bottom of the conveyor frame. Keyhole slots can be stamped anywhere in the frame bottom to meet application requirements. Mounting lock not included ORDERING INFORMTION WW - Distance from wiper end in inches Conveyor Width Reference. ee conveyor section for sizes 75 = Mounting lock Kit, 77 = Keyhole lot 400 eries lock Example: : 400 eries Mounting lock for 6 (52) wide conveyor, centered (76) from wiper end of the conveyor. lock 2 Example: : 400 eries Mounting lock for 6 (52) wide conveyor, centered.5 (85) from wiper end of the conveyor. 6

23 400 & 6200 ERIE: UPPORT TND Fixed eight upport tands Fixed Foot Model tand Width (WW) 2 (05) 2 (5) increments up to (29) Part # Reference 2 in 02 increments up to tand eight ()* 5 9 in (25) increments up to (8-48) (24-255) Part # Reference 59 in 00 increments up to Metric fasteners 4 (02) eight djustment * Dependent on stand width, stands over 42 (067) may include outriggers WW wivel ocking Caster Model tand Width (WW) 2 (05) 2 (5) increments up to (29) Part # Reference 2 in 02 increments up to tand eight ()* in (25) increments up to (508-) ( ) Part # Reference 2024 in 00 increments up to Full width top plate on 2 wide stands only djustable eight upport tands Fixed Foot Model tand Width (WW) 2 (05) 2 (5) increments up to (29) Part # Reference 2 in 02 increments up to tand eight () * 54-72* 66-84* 78-96* (05-0) (0-8) (56-42) (406-6) (48-686) (-94) (762-29) ( ) (72-829) (676-24) (98-248) Part # Reference wivel ocking Caster Model tand Width (WW) 2 (05) 2 (5) increments up to (29) Part # Reference 2 in 02 increments up to tand eight () * 59-77* (42-457) ( ) (48-559) (5-6) (-787) (77-04) (762-46) (94-65) ( ) Part # Reference ingle Post & Pillar upport tands Metric fasteners * Dependent on stand width, stands over 42 (067) tall may include outriggers WW Full width top plate on 2 wide stands only WW WW TNDRD IZE tand Width (WW) (44) (70) (95) (27) (52) (20) (254) (05) (56) (406) (457) ingle Post upport tand D Pillar tand (must be secured to floor) Part# Reference tand eight () (406-6) (-864) (8-067) (06-270) (29-47) Part# Reference ase Diameter (D) 24 () 27 (686) 0 (762) (88) 6 (95) Casters do not change overall height Metric fasteners hort upport tands 62 Fixed Foot Model tand Width (WW) 2 (05) 2 (5) increments up to (29) Part # Reference 2 in 02 increments up to tand eight () in (25) increments up to (52-20) (05-56) Part # Reference 08 in 00 increments up to 24 wivel ocking Caster Model tand Width (WW) 2 (05) 2 (5) increments up to (29) Part # Reference 2 in 02 increments up to tand eight () in (25) increments up to (279-0) (42-48) Part # Reference in 00 increments up to WW (2) WW Full width top plate on 2 wide stands only

24 UPPORT TND Fully djustable upport tands Fixed Foot Model tand Width (WW).75 (44) 2.75 (70).75 (95) 5 (27) 6 (52) 2 (5) increments up to (29) tand Width Reference increments up to Top Of elt Range (79-48) (05-787) (05-097) (05-97) (05-702) tand eight Reference wivel ocking Caster Model tand Width (WW).75 (44) 2.75 (70).75 (95) 5 (27) 6 (52) 2 (5) increments up to (29) tand Width Reference In 02 increments up to Top Of elt Range (05-48) (42-787) (42-097) (42-97) (42-702) tand eight Reference WW (24) WW Metric fasteners Multi Tier tands WW (208) Minimum Tier eight Per Conveyor 2200 Flat elt 2 (05) 2200 Cleated elt 5 (8) WW WW (208) ase Full width top plate on 2 wide stands only WW Tier ase tand Width (WW) 2 (05) 2 (5) increments up to (29) Part # Reference 2 02 increments up to tand eight () 2 (05) 2 (5) increments up to... (524) Part # Reference increments up to... 2 Tier tand Width (WW) 2 (05) 2 (5) increments up to (29) Part # Reference 2 02 ncrements up to tand eight () 2 (05) (25) increments up to... 6 (94) Part # Reference increments up to Note: Do not use with support stands equipped with casters. upport tands must be anchored to the floor. Do not use if conveyed product overhangs the edge of the conveyor belt due to pinch point created. ORDERING INFORMTION 9 M T T W W - (min) (max) F ssembly (not available for pillar, single post, tall & multi tier stands) P partially assembled tandard assembly (some parts may be separate to accomodate shipping) Feet or Casters (not available for multi tier stands) F fixed foot pad C total lock swivel caster eight Reference refer to stand tables top of leg for multi tier Width Reference refer to stand tables tand short stand F fixed height adjustable height F fully adjustable T multi tier stand base T2 multi tier stand tier FT tall fixed* T tall adjustable* P single post P pillar support Documentation anguage M U English tand tyle 2-legged stand 4 ingle post or pillar style EXMPE: 9M2-226CP *Tall stands are required when the stand width is.5 times the stand height. Note: Due to the wide variety of conveyor and stand options along with possible configurations, stability is final setup of the responsibility of the end user. 6

25 400 & 6200 ERIE: UPPORT TND CCEORIE tand ccessories djustable Tie racket. () +.9 (48).28 (7) Diameter. ().0 (25) 0.9 (2) Compatible with steel and aluminum support stands. ecure critical stand and conveyor locations. ength () adjusts + 0, -.25 (286 mm). Includes metric mounting hardware. 27M M M M M djustable Tie racket, 2 () djustable Tie racket, (94) djustable Tie racket, 4 (,29) djustable Tie racket, 5 (,524) djustable Tie racket, 6 (,829) ottom Mount tand racket olts to 90 standard load gearmotor Includes metric mounting hardware M 6997WWM racket only, for 2 to 5 wide conveyors. racket ssembly, 06 and wider 2200 conveyors. Diagonal racing (6200 eries Only) For use on steel, aluminum and single post support stands with casters. Metric fastener mounting hardware included. For use on all stands with casters and any stands over 72 (829) tall. One brace per stand for conveyors up to 24 wide () Two braces per stand for conveyors over 24 wide () for two-legged style stands up to 0 tall (762) for two-legged style stands over 0 tall (762) for ingle Post and Pillar stands over 0 tall (762) Common Mount Kit (6200 eries Only) *dds 2 (5) to stand height tand accessory for mounting multiple conveyors in parallel to one stand. Not for use with 400 eries - see Gang Drive Mounting Package on Page 40 ORDERING INFORMTION 9MCM ww - n n = number of conveyors per stand (6 conveyors max.) ww = width 2 in 2 increments up to 48 Tall upport tands Tall tands are the Fixed eight and djustable eight tands as shown with additional outrigger support for added stability. These outriggers are required when the height of the stand exceeds.5x its width, and they add 6 to stand width. Tall stands over 6 tall include diagonal bracing. Fine djustment Kit Provides fine height adjustment via a threaded bolt. For use with Fixed eight tands. Note: Due to the wide variety of conveyor and stand options along with possible configurations, stability of the final setup is the responsibility of the end user. Part #:

26 400 & 6200 ERIE: CCEORIE Drive haft ccessories upport lock Clear Cover.0 (25).50 (8) 2.5 (64).8 (5) For 400 & 6200 eries Gang Drive Conveyors 4- upport lock,.8 ex haft olid Coupling, ex to ex.25 (2) Includes metric set screws ex haft.0 (25).8" cross the flats 20064M olid Coupling,.8 ex to ex ex haft, steel, 48 (,29) long ex haft, stainless steel, 72 (,829) long Fits 400 & 6200 light load top mount and standard & heavy load top and bottom mount packages M M Clear cover, ordered with mounting package Clear cover, ordered separately Flexible Coupling 2.6 (67).5 (8) () Includes E set screws, ( & C) metric set screws. Coupling M29 2M0 2M Flexible Coupling,.50 bore x.8 hex Flexible Coupling,.6 bore x.8 hex Flexible Coupling, 2mm bore x.8 hex Flexible Coupling, 9mm bore x.8 hex Flexible Coupling, 2mm bore x 2mm bore ervice ccessories Grease dapter Tool Kit Grease leeves M dapter, 400 eries dapter, 6200 eries Gang Drive M Tool Kit, 400 eries Tool Kit, 6200 eries M 20099M leeve, 400 eries, traight leeve, 400 eries, 90 leeve, 6200 eries, Gang Drive traight, 90 leeve, 6200 eries, Gang Drive traight 66

27 PERFORMNCE CRT / DT Conveyor No-oad Torques (T No-load) verage No-load Torque* for 400 & 6200 eries Conveyors = Torque requirements for unloaded Center Drive Conveyors = Torque requirements for unloaded End Drive & Cleated Conveyors 2 in-lb (2.6 Nm) 20 in-lb (2. Nm) 25 in-lb (2.8 Nm) 0 in-lb (.4 Nm) 5 in-lb 5 in-lb (.7 Nm) (.7 Nm) 4 in-lb 2 in-lb (.5 Nm) 2 in-lb in-lb (.4 Nm) (.4 Nm) 0 in-lb (.2 Nm) 0 in-lb 9 in-lb (. Nm) (. Nm) (.0 Nm) 8 in-lb 7 in-lb (0.9 Nm) 6 in-lb (0.8 Nm) 5 in-lb (0.7 Nm) 4 in-lb (0.6 Nm) ( Nm) Note: The torque required to overcome the conveyor s initial startup inertia may temporarily exceed the average no-load torque by a factor of 2- times. *tated torques are average values based on Dorner standard belts running at 50 feet (5 meters) per minute..75" (44) 2.75" (70).75" (95) 5" (27) 6" (52) 8" (20) 0" (254) Conveyor elt Width 2" (05) 8" (457) Maximum Conveyor oad Charts Maximum evenly distributed load for: = Center Drive Conveyors = End Drive & Cleated Conveyors 90 lbs (4 kg) 05 lbs (47 kg) 20 lbs (54 kg) 20 lbs (54 kg) 20 lbs (54 kg) Drive haft Position 40 lbs (8 kg) 0 lbs (4 kg) 50 lbs (2 kg) 5 lbs (6 kg) lbs (27 kg) 42 lbs (9 kg) 75 lbs (4 kg) 50 lbs (2 kg) lbs (27 kg) 70 lbs (2 kg) 80 lbs (6 kg) 80 lbs (6 kg) 80 lbs (6 kg) ince belts are being pulled, positions & D are preferred. Pushing belts ( & C) reduce conveyor load capacity by approximately 66%..75" (44) 2.75" (70).75" (95) 5" (27) 6" (52) 8" (20) Conveyor elt Width 0" (254) 2" (05) 8" (457) Maximum evenly distributed load for: = Center Drive Conveyors = End Drive & Cleated Conveyors lbs (6 kg) 0 lbs (5 kg) 7 lbs (8 kg) 2 lbs (5 kg) 20 lbs (9 kg) 4 lbs (6 kg) 25 lbs ( kg) 7 lbs (8 kg) 0 lbs (4 kg) 20 lbs (9 kg) 5 lbs (6 kg) 2 lbs (0 kg) 40lbs (8 kg) 27 lbs (2 kg) 40 lbs (8 kg) 27 lbs (2 kg) 40lbs (8 kg) 27 lbs (2 kg).75" (44) 2.75" (70).75" (95) 5" (27) 6" (52) 8" (20) Conveyor elt Width 0" (254) 2" (05) 8" (457) 67