The ORIGINAL extruded-aluminum-frame conveyor. American Made and American Engineered

Transcription

1 American Made and American Engineered The ORIGINAL extruded-aluminum-frame conveyor

2 The Diebel Series The Diebel Series of Conveyors are designed to offer an economical method of transporting small, lightweight products. The overall profile is compact and the small diameter end rollers provide easy parts transfer from one convey to another. Options such as adjustable guide rails, sensor brackets, tight transfer end pulleys and transfer plates are available. The Diebel Series of aluminum frame conveyors is a low cost, ready to use solution for your automated systems needs. Table of Contents Area Page Area Page General Specifications 1 Model D-3300 Drive Locations 9-10 Diebel Tight Transfer 2 Frames 11 Model D-1300 Specifications 3 Supports 11 Model D-2300 Specifications 3-4 Options 11 Model D-3300 Specifications 4 Specialty Conveyors 12 Model D-1300 Drive Locations 5-6 Standard Belt Options 13 Model D-2300 Drive Locations 7-8 Speeds, Motors, Controllers & Photo Eyes 14 Specifications Model Position Light Duty D-1300 Ultra-Low Profile Medium Duty D-2300 Low Profile Diebel Model # D-1300 D-2300 D-2300 D-2300 (Tight Transfer) Heavy Duty D-3300 Low Profile D-3300 D-3300 D-3300 (Tight Transfer) Drive Location End & Center End Center Center End Center Center Lengths Infeed Pulley/ Roller Diameter Drive Pulley/ Roller Diameter Drive Shaft Diameter Frame Depth Maximum Capacity 40# 80# 80# 80# 200# 200# 200# # of T-Slots Motor Type Gearmotor Gearmotor Gearmotor Gearmotor Motor & Reducer Motor & Reducer Motor & Reducer Belt Widths/ Frame Style 2, 4, 6, 8, 12, & 18 BW s Plate & Rail Frame Box Beam Frame Plate & Rail Frame 1, 2, 4, & 6 BW s 8, 12, & 18 BW s Box Beam Frame Plate & Rail Frame 1, 2, 4, & 6 BW s 8, 12, & 18 BW s 1

3 The Diebel Series Tight Transfer Conveyors SIMPLE & EASY TRACKING SYSTEM SIDERAIL & SENSOR MOUNTING OPTIONS AVAILABLE MANY STANDARD OPTIONS AVAILABLE ALUMINUM BOX OR PLATE & RAIL CONSTRUCTION DISCHARGE STANDARD INFEED 2-1/4 Diameter Roller for Everyday Products S FROM 1-1/8 (D1300) TO 2-15/32 (D2300 & D3300) ALL PULLEYS AND ROLLERS HAVE A CROWNED FACE "WE CONVEY QUALITY" TO AID IN BELT TRACKING TIGHT TRANSFER INFEED (2) 1-1/8 Diameter Rollers for smaller, more difficult transfering products INFEED ALL STEEL PARTS ARE CLEAR ZINC COATED FOR A CLEAN MAINTENANCE FREE FINISH (ALSO AVAILABLE IN A 304 2B STAINLESS STEEL FINISH) PAGE REVISED 2/14/17 SLOTS MAKE FOR EASY ACCESSORY MOUNTING DIEBEL STRUCTOLINK SUPPORTS MAKE FOR EASY ADJUSTMENTS AND THE EXTRUSION SLOTS MAKE FOR EASY ACCESSORY MOUNTING NOTE: -ALL DIMENSIONS SHOWN ARE IN INCHES Model D-1300, D-2300, & D-3300 Infeed/Tail End Views ( BW = INF OAW ) ( BW = FW ) ( BW ) ( BW = INF OAW ) ( BW = FW ) ( BW ) ( BW = INF OAW ) ( BW = FW ) ( BW ) ROLLER DIA ROLLER DIA ROLLER DIA STANDARD INFEED (D-1300 ONLY) STANDARD INFEED (D-2300 & D-3300) TIGHT TRANSFER INFEED (D-2300 & D-3300) NOTE: ALL DIMENSIONS SHOWN ARE IN INCHES. 2

4 The Diebel Series Specifications Diebel Model D-1300 Light Duty Applications D-1300 End Drive ( OAHL = CONVEYING LENGTH " ) ( CONVEYING LENGTH ) OAW = BW " END WIDTH = BW " WIDTH = BW " 3.625" 1.125" 7.625" 9.344" D-1300 Center Drive ( CONVEYING LENGTH / OAHL ) WIDTH = BW " 7.438" OAW = BW " END WIDTH = BW " " 4.375" 6.375" 1.125" Diebel Model D-2300 Medium Duty Applications D1300 Center Drive Frame Mt Inline Under Conveyor (#2) D-2300 End Drive "WE CONVEY QUALITY" ( OAHL = CONVEYING LENGTH ) ( CONVEYING LENGTH ) END WIDTH = BW OAW = BW WIDTH = BW (6.844) (9.344) 3 D-2300 End Drive NOTES: - DIMENSIONS ARE SHOWN IN INCHES AND ARE SUBJECT TO CHANGE. - DRAWINGS SHOW STANDARD OPTIONS WITH STANDARD STYLE MOTORS. MOTOR DIMENSIONS CAN VARY. - ARROWS DEPICT PREFERRED BELT TRAVEL / PRODUCT FLOW. - CENTER S CAN BE PLACED ANYWHERE ALONG THE LENGTH OF THE EXCEPT THE LAST 3-1/2 FROM EITHER END.

5 The Diebel Series Specifications Diebel Model D-2300 Medium Duty Applications D-2300 Center Drive WIDTH = BW ( CONVEYING LENGTH / OAHL ) END WIDTH = BW OAW = BW (6.156) Diebel Model D-3300 Heavy Duty Applications D-3300 End Drive ( OAHL = CONVEYING LENGTH " ) ( CONVEYING LENGTH ) END WIDTH = BW " OAW = BW " WIDTH = BW " 1.219" 2.480" 6.656" " " D-3300 Center Drive D3300 End Drive Btm Mt Rt Angle Inf Facing (#23) ( CONVEYING LENGTH / OAHL ) " OAW = BW " END WIDTH = BW " " WIDTH = BW " 7.438" 2.480" NOTES: - DIMENSIONS ARE SHOWN IN INCHES AND ARE SUBJECT TO CHANGE. - DRAWINGS SHOW STANDARD OPTIONS WITH STANDARD STYLE MOTORS. MOTOR DIMENSIONS CAN VARY. D3300 Center Drive Frame Mt Rt Angle Discharge Facing (#19) - ARROWS DEPICT PREFERRED BELT TRAVEL / PRODUCT FLOW. - CENTER S CAN BE PLACED ANYWHERE ALONG Standard THE LENGTH Infeed OF THE Ends EXCEPT THE LAST 3-1/2 FROM EITHER END. 4

6 The Diebel Series Model D-1300 Drive Locations (7.531) (7.531) (7.531) #2 #3 D1300 D1300 #2 -#2 Center - Center Drive, Drive, Frame Frame Inline, Inline, Under Under Belt Belt D1300 #2 - Center Drive, Frame Inline, Under Belt Center Drive Frame Mount Inline Under Belt (15.375) (15.375) (15.375) (7.531) D1300 D1300 #2 -#3 Center - Center Drive, Drive, Frame Frame Inline, Right Under Angle, Belt Discharge Facing D1300 D1300 #3 #3 - Center - Center Drive, Drive, Frame Frame Right Right Angle, Angle, Discharge Facing Center Drive Frame Mount Right Angle Discharge Facing (15.375) USES SAME DRAWING AS D1300 #3 ABOVE USES USES SAME SAME DRAWING AS AS D1300 #3 #3 ABOVE D #4 D D1300 D1300 #3 -#4 Center - Center Drive, Drive, Frame Frame Right Right Angle, Angle, Discharge Infeed Facing Facing D1300 D1300 #4 #4 - Center - Center Drive, Drive, Frame Frame Right Right Angle, Angle, Infeed Infeed Facing Facing Center Drive Frame Mount Right Angle Infeed Facing D 5 #7 USES SAME DRAWING AS (9.375) D1300 #3 ABOVE (2.094) (9.375) (2.094) (9.375) (2.094) End D1300 Drive #7 Bottom - End Drive, Mount Bottom Inline Inline, Under Belt D1300 D1300 #4 #7 - Center - End Drive, Frame Bottom Right Inline, Angle, Under Infeed Belt Facing D1300 #7 - End Drive, Bottom Inline, Under Belt NOTES: - DIMENSIONS ARE SHOWN IN NOTES: INCHES AND ARE SUBJECT TO CHANGE. - DRAWINGS SHOW STANDARD NOTES: -DIMENSIONS OPTIONS SHOWN WITH STANDARD ARE IN INCHES, STYLE MOTORS. AND ARE MOTOR SUBJECT DIMENSIONS TO CHANGE. CAN VARY. - ARROWS DEPICT PREFERRED -DRAWINGS -DIMENSIONS BELT TRAVEL / SHOW SHOWN PRODUCT 'STANDARD' ARE FLOW. OPTIONS WITH 'STANDARD' STYLE MOTORS. MOTOR DIMENSIONS IN PARENTHESIS VARY DEPENDING IN INCHES, AND ARE SUBJECT TO CHANGE. NOTES: - CENTER S CAN BE PLACED -DRAWINGS -ARROWS ANYWHERE DEPICT SHOW ALONG 'STANDARD' PRODUCT THE LENGTH FLOW OF THE AS OPTIONS IT RELATES EXCEPT WITH THE TO LAST 'STANDARD' THE 3-1/2 FROM DESCRIPTION. STYLE EITHER MOTORS. END. MOTOR DIMENSIONS IN PARENTHESIS VARY DEPENDING O -DIMENSIONS SHOWN ARE IN INCHES, AND ARE SUBJECT TO CHANGE. -ARROWS DEPICT PRODUCT FLOW AS IT RELATES TO THE DESCRIPTION. -DRAWINGS SHOW 'STANDARD' OPTIONS WITH 'STANDARD' STYLE MOTORS MOTOR DIMENSIONS IN PARENTHESIS VARY DEPENDING ON

7 5 375 The Diebel Series Model D-1300 Drive Locations line, Under Belt, nline, Inline, Under Under Belt Belt # ht Angle, Discharge Facing, Right Angle, Discharge Facing ight Angle, Discharge Facing #9 VE #3 ABOVE RIVE #3 ABOVE #3 #3 ABOVE (7.563) (2.000) (7.563) (7.563) (2.000) (7.594) (4.906) (2.000) D1300 #8 - End Drive, Bottom (7.594) (7.594) (4.906) Right Angle, Infeed Facing (7.594) (4.906) D1300 D1300 #8 #8-- End End Drive, Drive, Bottom Bottom Right Angle, Infeed Facing End Drive Bottom Mount Right Angle Infeed Facing (8.250) (8.250) (8.250) (1.969) (8.250) (1.969) (1.969) (1.969) D #9 - End Drive, Top Inline, Over Belt D1300 #9 - End Drive, Top Inline, Over Belt D1300 #9 - End Drive, Top Inline, Over Belt End Drive Top Mount Inline Over Belt (7.563) (7.563) (7.563) (1.500) (1.500) (1.500) ht Angle, Infeed Facing, Right Angle, Infeed Facing ight Angle, Infeed Facing # D #12 - End Drive, Top Right Angle, Discharge Facing D1300 #12 - End Drive, Top Right Angle, Discharge Facing D1300 #12 - End Drive, Top Right Angle, Discharge Facing End Drive Top Mount Right Angle Disharge Facing (3.500) (6.625) (BW+4.906) (3.500) (6.625) (BW+4.906) (3.500) (6.625) (BW+4.906) (3.500) (6.625) (BW+4.906) 94).094) ) (1.750) (1.750) (3.469) 25 (1.750) (3.469) (3.469) nline, Under Under Belt Belt line, Under Belt #13 End Drive Shaft Mount Inline NOTES: - DIMENSIONS ARE SHOWN IN INCHES AND ARE SUBJECT TO CHANGE. - DRAWINGS SHOW STANDARD OPTIONS WITH STANDARD STYLE MOTORS. MOTOR DIMENSIONS CAN VARY.. OR MOTOR DIMENSIONS IN VARY ON S. MOTOR DIMENSIONS DIMENSIONS IN PARENTHESIS - ARROWS DEPICT IN PARENTHESIS VARY PREFERRED VARY DEPENDING BELT TRAVEL DEPENDING ON / PRODUCT HORSEPOWER, FLOW. HORSEPOWER, VOLTAGE, VOLTAGE, SPEEDS, SPEEDS, ETC. - CENTER S CAN BE PLACED ANYWHERE ALONG THE LENGTH OF THE EXCEPT THE LAST ETC. 3-1/2 FROM EITHER END. OTOR DIMENSIONS IN PARENTHESIS VARY DEPENDING ON HORSEPOWER, VOLTAGE, SPEEDS, ETC. D1300 #13 - End Drive, Shaft Inline D1300 #13 - End Drive, Shaft Inline D1300 LOCATIONS (PAGES D1300 LOCATIONS #5 & #6) REVISED (PAGES #5 & #6) REVISED

8 The Diebel Series Model D-2300 Drive Locations (8.656) (8.656) (8.656) (7.531) (7.531) (7.531) #2 D2300 D2300 #2 #2 - Center - Center Drive, Frame Inline, Under Belt Belt D2300 #2 - Center Drive, Frame Inline, Under Belt Center Drive Frame Mount Inline Under Belt (8.656) (7.531) (15.375) (15.375) (15.375) #3 D2300 D2300 #2 #3 - Center - Center Drive, Drive, Frame Inline, Right Angle, Under Discharge Belt Facing D2300 #3 #3- - Center Drive, Frame Right Angle, Discharge Facing Facing Center Drive Frame Mount Right Angle Discharge Facing (15.375) USES SAME DRAWING AS D2300 #3 ABOVE USES SAME DRAWING AS D2300 #3 ABOVE USES SAME DRAWING AS D2300 #3 ABOVE T T 7 #4 T #7 D2300 #4 - Center Drive, Frame Right Angle, Infeed Facing D2300 D2300 #3 #4- - Center Center Drive, Frame Right Angle, Infeed Discharge Facing Facing D2300 #4 - Center Drive, Frame Right Angle, Infeed Facing (BW+3.094) (BW+3.094) (BW+3.094) (9.375) USES SAME DRAWING AS (1.531) D2300 #3 ABOVE (9.375) (9.375) (1.531) (6.656) D2300 #7 - End Drive, Bottom (1.531) Inline, Under Belt (6.656) Center Drive Frame Mount Right Angle Infeed Facing End Drive Bottom Mount Inline Under Belt D2300 D2300 #4 #7 - - Center End Drive, Drive, Bottom Frame Inline, Right Under Angle, Belt (6.656) Infeed Facing D2300 #7 - End Drive, Bottom Inline, Under Belt NOTES: NOTES: - DIMENSIONS ARE SHOWN IN INCHES -DIMENSIONS AND ARE SUBJECT SHOWN TO CHANGE. ARE IN INCHES, AND ARE SUBJECT TO CHANGE. - DRAWINGS SHOW STANDARD OPTIONS WITH STANDARD STYLE MOTORS. MOTOR DIMENSIONS CAN VARY. -DRAWINGS SHOW 'STANDARD' OPTIONS WITH 'STANDARD' STYLE MOTORS. MOTOR DIMENSIONS IN PARENTHESIS VARY DEPENDING - ARROWS DEPICT PREFERRED BELT NOTES: -ARROWS TRAVEL / PRODUCT DEPICT FLOW. PRODUCT FLOW AS IT RELATES TO THE DESCRIPTION. - CENTER S CAN BE PLACED ANYWHERE ALONG THE LENGTH OF THE EXCEPT THE LAST 3-1/2 FROM EITHER END. -DIMENSIONS SHOWN ARE IN INCHES, AND ARE SUBJECT TO CHANGE. -DRAWINGS SHOW 'STANDARD' OPTIONS WITH 'STANDARD' (BW+3.094) STYLE MOTORS. MOTOR DIMENSIONS IN PARENTHESIS VARY DEPENDIN

9 line, Under Belt Inline, nline, Under Under Belt Belt t, Inline, Under Belt The Diebel Series Model D-2300 Drive Locations # (BW+3.094) (BW+3.094) (BW+3.094) (BW+3.094) (1.125) (7.594) (1.125) (1.125) (5.094) (1.125) D2300 (7.594) #8 - End Drive, Bottom (7.594) (5.094) Right Angle, Infeed Facing (5.094) (7.594) (5.094) D2300 D2300 #8 #8 - - End End Drive, Drive, Bottom Bottom Right Right Angle, Angle, Infeed Infeed Facing Facing D2300 #8 - End Drive, Bottom Right Angle, Infeed Facing End Drive Bottom Mount Right (BW+3.094) Angle Infeed Facing (8.250) (BW+3.094) (BW+3.094) (BW+3.094) (1.406) (8.250) (8.250) (8.250) (1.406) (1.406) (1.406) ight Angle, Discharge Facing ight Angle, Discharge Facing t, ight Right Angle, Angle, Discharge Discharge Facing Facing #9 VE #3 ABOVE IVE #3 ABOVE #3 #3 ABOVE ight Angle, Infeed Facing ight Angle, Infeed Facing Right t, Right Angle, Angle, Infeed Facing #12 D2300 #9 - End Drive, Top Inline, Over Belt D2300 #9 - End Drive, Top Inline, Over Belt D2300 #9 - End Drive, Top Inline, Over Belt D2300 End Drive #9 Top - End Mount Drive, Top Inline Inline, Over Belt (7.594) (7.594) (7.594) (BW+3.094) (BW+3.094) (5.094) (BW+3.094) (5.094) (5.094) (0.938) (0.938) (0.938) D2300 #12 - End Drive, Top Right Angle, Discharge Facing D2300 #12 - End Drive, Top Right Angle, Discharge Facing D2300 # End Drive, Top Right Angle, Discharge Facing End Drive Top Mount Right Angle Discharge Facing (3.500) (3.500) (3.500) (6.625) (6.625) (6.625) (BW+4.688) (BW+4.688) (BW+4.688) (6.656) (6.656) (6.656) line, Under Belt line, Inline, Under Under Belt Belt #13 NOTES: - DIMENSIONS ARE SHOWN IN INCHES AND ARE SUBJECT TO CHANGE. - DRAWINGS SHOW STANDARD OPTIONS WITH STANDARD STYLE MOTORS. MOTOR DIMENSIONS CAN VARY. OTOR DIMENSIONS IN - ARROWS PARENTHESIS DEPICT PREFERRED VARY DEPENDING BELT TRAVEL ON / ON PRODUCT HORSEPOWER, FLOW. VOLTAGE, SPEEDS, ETC. ETC. RS. MOTOR DIMENSIONS - CENTER IN PARENTHESIS S CAN BE PLACED VARY DEPENDING ANYWHERE ALONG HORSEPOWER, THE LENGTH OF THE VOLTAGE, EXCEPT SPEEDS, THE LAST ETC. 3-1/2 FROM EITHER END. MOTOR DIMENSIONS IN PARENTHESIS VARY DEPENDING ON HORSEPOWER, VOLTAGE, SPEEDS, ETC. (1.000) (1.000) (1.000) (1.000) D2300 End #13 #13 Drive - End - End Drive, Drive, Shaft Shaft Shaft Inline Inline D2300 D2300 #13 # End End Drive, Drive, Shaft Shaft Inline Inline D2300 D2300 LOCATIONS D2300 D2300 LOCATIONS LOCATIONS (PAGES #7 #7 & #8) & #8) REVISED (PAGES #7 & #8) REVISED (PAGES #7 & #8) REVISED

10 The Diebel Series Model D-3300 Drive Locations (32.813) (32.813) (BW+5.875) (BW+5.875) (BW+5.000) (BW+5.000) #19 D3300 D3300 #19 #19 - Center Center Drive, Drive, Frame Frame Right Right Angle, Angle, Discharge Discharge Facing Facing D3300 #19 - Center Drive, Frame Right Angle, Discharge Facing Center Drive Frame Mount Right Angle Discharge Facing (BW+5.875) (32.813) (BW+5.000) USES SAME DRAWING AS D3300 #19 ABOVE USES SAME DRAWING AS D3300 #19 ABOVE #20 D3300 #20 - Center Drive, Frame Right Angle, Infeed Facing D3300 #19 - Center Drive, Frame Right Angle, Discharge Facing D3300 #20 Center Drive, Frame Right Angle, Infeed Facing Center Drive Frame Mount Right Angle Infeed Facing USES SAME DRAWING AS D3300 #19 ABOVE (BW+4.000) 1 (BW+4.000) #21 #22 (17.688) (17.688) (BW ) D3300 #21 - Center Drive, Shaft Right (BW ) Angle, Discharge Facing D3300 #20 - Center Drive, Frame Right Angle, Infeed Facing D3300 #21 Center Drive, Shaft Right Angle, Discharge Facing Center Drive Shaft Mount Right Angle Discharge Facing (BW+4.000) 1 (BW+4.000) (BW+4.000) (27.813) (17.688) (BW ) (27.813) D3300 #22 - Center Drive, Shaft Right Angle, Infeed Facing D3300 #21 - Center Drive, Shaft Right Angle, Discharge Facing D3300 #22 Center Drive, Shaft Right Angle, Infeed Facing (BW ) Center Drive Shaft Mount Right Angle (BW ) Infeed Facing NOTES: NOTES: NOTES: - DIMENSIONS ARE SHOWN IN INCHES -DIMENSIONS -DIMENSIONS AND ARE SUBJECT SHOWN SHOWN TO CHANGE. ARE IN INCHES, AND ARE SUBJECT TO CHANGE. ARE IN INCHES, AND ARE SUBJECT TO CHANGE. - DRAWINGS SHOW STANDARD -DRAWINGS -DRAWINGS OPTIONS WITH SHOW SHOW STANDARD 'STANDARD' 'STANDARD' STYLE MOTORS. MOTOR OPTIONS OPTIONS DIMENSIONS WITH 'STANDARD' WITH 'STANDARD' CAN VARY. STYLE MOTORS. MOTOR DIMENSIONS IN PARENTHESIS VARY DEPEND STYLE MOTORS. MOTOR DIMENSIONS IN PARENTHESIS VARY DEPEN - ARROWS DEPICT PREFERRED BELT NOTES: TRAVEL -ARROWS -ARROWS / PRODUCT DEPICT DEPICT FLOW. PRODUCT FLOW AS IT RELATES TO THE DESCRIPTION. PRODUCT FLOW AS IT RELATES TO THE DESCRIPTION. - CENTER S CAN BE PLACED -DIMENSIONS ANYWHERE -JUNCTION -JUNCTION ALONG BOX SHOWN BOX THE OF OF LENGTH MOTORS MOTORS ARE OF IN THE INCHES, SHOWN SHOWN EXCEPT EXTEND AND EXTEND ARE THE PAST PAST LAST SUBJECT 3-1/2 THE MOTOR THE MOTOR FROM CHANGE. EITHER CASE ", AND THE BOX DIMENSIONS ARE 2.750" x 2.750" CASE END. ", (BW+4.000) AND THE BOX DIMENSIONS ARE 2.750" x 2.750" -DRAWINGS SHOW 'STANDARD' OPTIONS WITH 1 'STANDARD' STYLE MOTORS. MOTOR DIMENSIONS IN PARENTHESIS VARY DEPEN -ARROWS DEPICT PRODUCT FLOW AS IT RELATES TO THE DESCRIPTION.

11 The Diebel Series.875) 5.875) ).000) 5.000) ) Model D-3300 Drive Locations, Right Angle, Discharge Facing Right Angle, Discharge Facing unt,, Right Right Angle, Angle, Discharge Discharge Facing Facing #23 IVE #19 ABOVE #19 #19 ABOVE ABOVE IVE #19 ABOVE, Right Angle, Infeed Facing unt, Right Right Angle, Angle, Infeed Infeed Facing Facing, Right Angle, Infeed Facing # ) W+4.000) ) (BW ) (BW ) Right (BW ) Angle, Discharge Facing nt, Right Right Angle, Angle, Discharge #27 Facing Right Angle, Discharge Facing.000) ) 4.000) (BW ) (BW ) nt, Right Right Right (BW ) Angle, Angle, Angle, Infeed Infeed Infeed Facing Facing Facing #28 Right Angle, Infeed Facing (BW+4.688) (BW+4.688) (BW+4.688) (19.938) (10.219) (BW+5.594) (19.938) (10.219) (BW+5.594) (19.938) (10.219) (BW+5.594) D3300 #23 - End Drive, Bottom Right Angle, Infeed Facing D3300 #23 End Drive, Bottom Right Angle, Infeed Facing D3300 D3300 #23 #23-- End End Drive, Bottom Right Angle, Infeed Facing Facing End Drive Bottom Mount Right Angle Infeed Facing (18.188) (18.188) (18.188) (18.188) (BW+6.250) (BW+6.250) (BW+6.250) (BW+5.406) (BW+6.250) (BW+5.406) (BW+5.406) (BW+5.406) (4.875) (15.781) (4.875) (15.781) (4.875) (15.781) (4.875) (15.781) D3300 #24 - End Drive, Top Right Angle, Infeed Facing D3300 D3300 #24 #24 End - End Drive, Drive, Top Top Right Right Angle, Angle, Infeed Infeed Facing Facing D3300 #24 - End Drive, Top Right Angle, Infeed Facing End Drive Top Mount Right Angle Infeed Facing (BW ) (3.313) (BW ) (3.313) (3.313) (3.313) (15.344) (BW ) (15.344) (15.344) (15.344) (8.031) (8.031) (8.031) (8.031) (1) (1) (1) D3300 #27 - End Drive, Shaft Right Angle, Infeed Facing D3300 #27 #27 End - End Drive, Shaft Right Angle, Infeed Facing D3300 #27 - End Drive, Shaft Right Angle, Infeed Facing End Drive Shaft Mount Right Angle Infeed Facing (3.313) (3.313) (3.313) (8.031) (8.031) (21.750) (21.750) (21.750) (BW ) (8.031) (10.844) (10.844) D3300 D3300 #28 #28 - End D3300 #28 End - End Drive, Drive, Drive, Shaft Shaft Shaft Right Right Angle, Angle, Discharge Discharge Facing Facing End Drive Shaft (10.844) Mount Right Angle Discharge Facing NOTES: - DIMENSIONS ARE SHOWN IN INCHES AND ARE SUBJECT TO CHANGE. RS. MOTOR DIMENSIONS OTORS. MOTOR DIMENSIONS - DRAWINGS PARENTHESIS SHOW PARENTHESIS STANDARD VARY VARY DEPENDING DEPENDING OPTIONS WITH ON HORSEPOWER, MOTOR DIMENSIONS IN PARENTHESIS VARY DEPENDING ON ON STANDARD HORSEPOWER, HORSEPOWER, STYLE VOLTAGE, MOTORS. VOLTAGE, VOLTAGE, MOTOR SPEEDS, SPEEDS, SPEEDS, DIMENSIONS ETC. ETC. ETC. CAN VARY. ION. - ARROWS DEPICT PREFERRED BELT TRAVEL / PRODUCT FLOW. ND ", D AND THE THE BOX BOX DIMENSIONS DIMENSIONS - CENTER ARE S ARE 2.750" 2.750" CAN x 2.750" BE x PLACED 2.750" ANYWHERE ALONG THE LENGTH OF THE EXCEPT THE LAST 3-1/2 FROM EITHER END. RS. THE MOTOR BOX DIMENSIONS ARE IN PARENTHESIS 2.750" x 2.750" VARY DEPENDING ON HORSEPOWER, VOLTAGE, SPEEDS, ETC. (BW ) (BW ) D3300 #28 - End Drive, Shaft Right Angle, Discharge Facing D3300 LOCATIONS D3300 LOCATIONS (PAGES #9 (PAGES #9 #9& &#10) REVISED REVISED D3300 LOCATIONS (PAGES #9 & #10) REVISED 2-15

12 The Diebel Series Options Diebel Series Conveyor Frames Diebel Series Standard Support Leg Configuration "WE CONVEY QUALITY" A TYP (FW) (3.000) 1" Extrusion Used for D-2300 Series 1" Belt Width B (2.000) (2.000) Box Beam Extrusions (D-2300 & D-3300 Series) Used for D-2300 & D-3300 Series Belt Widths 2", 4", & 6" Sensor Brackets (19.313) FOR 1"-8" BW'S (24.313) FOR 12"-18" BW'S STANDARD SUPPORT LEG CONFIGURATION Low Profile (D-1300 Series Only) Used for D-1300 Series Belt Widths 2", 4", 6", 8", 12", & 18" C /8-16 UNC Thread /8-16 UNC Thread Plate & Rail Frame (D-2300 & D-3300 Series) Used for D-2300 & D-3300 Series Belt Widths 8", 12", & 18" STD Leveling Pads D-0706 A " Locking Caster B Frame Type T-Slots Center-to-Center A Dimensions Overall Frame Height B Frame Dimensions by Type and Associated Belt Widths Center of Top T-Slot to Top-of-Frame C Overall Frame Width Diebel Belt Widths Extrusion N/A N/A N/A N/A N/A N/A Box Beam Extrusion N/A N/A N/A N/A Low Profile N/A N/A Plate & Rail N/A Diebel Series Side Fence & Guide Systems Adjustable Rails (Light Duty) Adjustable Rails (Heavy Duty) Fixed Rails (.5 to 3.5 high) Cleats up to 1.5 high 11 NOTE: CONSULT YOUR NLE SALES REPRESENTATIVE FOR OTHER AVAILABLE OPTIONS.

13 The Diebel Series Specialty Conveyors O-Ring belting for uniquely shaped parts and specific contact point requirements. Dual Belt Conveyor Product reorienting 90 bump and turn Conveyors as short as 12. Side transfer from belt to belt. Tight Transfer Feeding 90 Turn Product reorienting 180 flip leading edge maintained. Z configuration conveyors with or without cleated belting. Multiple belts with one drive for special parts handling. 12

14 The Diebel Series GENERAL PURPOSE COMMON DIEBEL SERIES BELTS *2 Ply 70 Blank PVC x IMPG (Spec #251) (Temp. Range 20 F to 180 F) (.093 Thick) This oil and cut resistant PVC cover is the ideal surface for general purpose conveying. The monofilament (multi-plied-2 plies or more) style construction provides strength and flexibility. This belt runs smooth, flat and quiet because the bottom is impregnated (coated) with a filler material resulting in a soft and level, low noise surface. 2 Ply Black Polyurethane x IMPG, Highly Conductive (ACS Type D Bolt) (Temp. Range 22 F to 176 F) (.05 Thick) (ACS Type D belt black) Used for conducting static charges from a product to the conveyor. ACCUMULATION 2 Ply White Polyurethane, Anti-Static, Non-Adhesive (ACS Type A Belt) (Temp. Range 5 F to 176 F) (.05 Thick) Used with accumulators or diverters. Approved by FDA/USDA for food, chemical and pharmaceutical applications. Easy to clean. Anti-static. Finger-spliced endless belt. 2 Ply Gray Polyurethane x IMPG, Non-Adhesive (ACS Type XVT Belt) (Temp. Range 4 F to 176 F) (.06 Thick) Used with harse environments like cut metal or stampings. Good accumulation. ROUGH TOP *2 Ply Black Longitudinal Ribbed Top x Bare Back (Spec #253X) (Temp. Range 15 F to 175 F) (.09 Thick) This belt is designed for high and steep incline applications. The longitudinal raised ribbed surface literally grips and holds the parts being conveyed. This belt will run smooth, flat and quiet due to the bare back low friction, low noise surface. This belt is especially suited for plastic totes. This s a good belt for steep inclines/declines. *2 Ply Gray PVC Rough Top, Diamond Pattern (ACS Type C Belt Gray) (Temp. Range 23 F to 122 F) (.07 Thick) Very adhesive. Used for steep inclines textured with 1/16 inverted diamond pattern. URETHANE WHITE BELTS *2 Ply Green Urethane x IMPG Back (Spec #249) (Temp. Range 20 F to 180 F) (.050 Thick) An economical yet high quality thin urethane belt with excellent cut and gouge resistance. This is an excellent choice for conveying sharp parts where an abundance of oil is present. This belt runs smooth, flat and quiet because the bottom is impregnated (coated) with a filler material resulting in a soft and level, low noise surface. This smooth top belt is also a good choice for light duty accumulating applications. *2 Ply White PVC (Spec #224) (Temp. Range 20 F to 180 F) (.031 Thick) Anti-static, FDA and USDA accepted general food conveying belt. This low cost belt is ideal for general transporting any food product and in an all non-marking applications. 1 Ply White Urethane x IMPG Bottom (Spec #222) (Temp. Range 20 F to 180 F) (.031 Thick) This belt has a smooth non-adhesive white urethane top cover. Excellent choice for cooling tunnels and applications requiring a high release surface. This belt runs smooth, flat and quiet because the bottom is impregnated (coated) with a filler material resulting in a soft and level, low noise surface. White PTFE Teflon Impregnated Non-Adhesive (ACS HTT Belt) (Temp. Range 4 F to 176 F) (.06 Thick) Used for gluing and heat-sealing applications. Works well for high heat (480 F). Good release characteristics. Finger-spliced endless belt. *2 Ply White Urethane x IMPG Bottom (Spec #223) (Temp. Range 20 F to 180 F) (.062 Thick) This belt s smooth non-adhesive white urethane top cover is ideal for applications where added strength and good release characteristics are required. It runs smooth, flat and quiet because the bottom is impregnated (coated) resulting in a soft and level, low noise surface. FDA and USDA accepted. *2 Ply White Polyurethane, Anti-Static, Slightly Adhesive (ACS Type B Belt White) (Temp. Range 22 F to 176 F) (.05 Thick) Slightly adhesive used for slight inclines, FDA /USDA Approved Thermo) 13

15 The Diebel Series Speeds/Motors/Controllers/Options Standard Speed Ranges Model D-1300 Model D-2300 Model D FPM FPM FPM Standard Gear Motors Standard Motor 1/30 HP 1/17 HP 1/3, 1/2 HP AC 200V (1 or 3 phase) 220V (1 or 3 phase) 230V (1 or 3 phase) DC 110V (1 phase) 115V (1 phase) 230V (3 phase) DC 130V (1 phase) 230V (3 phase) AC & DC 115/230V (1 phase) 230/460V (3 phase) 230/460V (3 phase) Standard AC Controller Standard DC Controller Custom Designed Pre-wired Systems Whether your project includes packaging, material handling or automation, New London Engineering can custom design an electrical control panel for you. Simply tell us what you want the system to do and we will build the electrical system. 14

16 CUSTOM AND STANDARD CONVEYORS We are a full line conveyor supplier specializing in engineering high quality, quick delivery conveyors. Accumulation Conveyors Belt Driven Live Roller Conveyors Bulk Material Handling Conveyors Cleated Belt Parts Conveyors Chain Driven Live Roller Conveyors Chain Transfers Drag Conveyors Floor-to-Floor Conveyors Gravity Roller Magnetic Conveyors Pallet Dispensers Power Roller Conveyors PlastiTrak A full line of plastic belt conveyors Quick Start Electrical Controls Slat Conveyors Slider Bed Conveyors Specialty Conveyors SteelTrak Hinged Steel Belt Conveyors ToughTrak Tough and durable thin line conveyors Turntables UpTime Express 24 hour shipments V-Belt Conveyors Wire Mesh Conveyors 1700 Division Street New London, WI Orders Online NLECO.com Fax REPLACEMENT PARTS For easy part identification, go to NLECO.com and click on Replacement Parts