6200 Series General Specifications:

Transcription

1 6200 ERIE 6200 eries General pecifications: Flat elt End Drive, Cleated elt, and Center Drive models Loads up to 20 lbs. (54 Kg) Lengths up to 24 (7,5) Widths up to 8 (457) (25 mm) diameter head and tail pulleys Models vailable p p l i c a t i o n s: Metal tamping Packaging Testing and Inspection Clean Room Manual ssembly Machine Part andling 2

2 INDEX Wedge-Lok ystem V-Guided elts 6200 ERIE INDEX Flat elt End Drive... 4 Flat elt Center Drive... 6 Cleated elt End Drive... 8 Profiles elting Gearmotor Mounting Packages Gearmotors upport tands ccessories Performance Charts / Data Rack & Pinion elt Tension

3 6200 ERIE: FLT ELT END DRIVE 6200 pecifications: gauge stainless steel roll formed frame ealed bearings elt widths:.75 (44) to 8 (457) Conveyor Lengths: 2 (60) to 8 (8,486).5 (8) bottom of frame to top of belt 2mm diameter integral drive shaft The (25) diameter drive pulley turns approximately.4 (86) of belt per revolution Load capacity up to 80 Lbs* (6 Kg) elt speeds up to 255 ft/min. (78 M/min.) Metric fasteners Mild steel head and tail plates with black nitrite finish Motion sensor switch ready Optional Gang Drive Pulleys Features/enefits: Wedge-Lok system for impact protection treamlined design fits where other conveyors do not Quick 5 minute belt change for increased uptime Low maintenance sealed bearings in both head and tail pulleys Lengths in.2 (4) increments elt materials to match application requirements Quick clamp rail for easy mounting of bolt-on accessories Rack and pinion design offers fast single point belt tensioning V-Groove frame with guided belt ensures accurate tracking Durable.25 (6) thick bottom wiper Optional spindles for gang drive applications Magnetic models available Models available ** Gang Drive tail pulley requires periodic greasing. NEW Wedge-Lok ystem What is it? The Conveyor headplates, which retain the conveyor pulleys and belt tension racks, are slightly tapered. What is the dvantage? In harsh or frequently changing production environments, equipment can be damaged as it is quickly moved to different applications. Dorner s patented Wedge-Lok ystem protects the conveyor end from damage by locking the pulley end from movement on sharp impact. Flat elt & Cleated elt End Drive Conveyors feature a quick 5 minute belt change. Loosen fasteners and collapse tail section. Remove old belt and replace. djust tension on new belt, tighten fasteners and go! 4 Conveyor load capacity depends on conveyor size, incline, motor position, accumulated loads and other factors. ee Performance Charts / Data section for details. Order gearmotor mounting packages and gearmotors separately; see pages 45 & 52. For support stands and accessories, see pages 60 & 65

4 TNDRD IZE Conveyor Width Reference Conveyor elt Width (W).75 (44) 2.75 (70).75 (95) 5 (27) 6 (52) 8 (20) 0 (254) 2 (05) Conveyor Length Reference increments up to (457) Conveyor Length (L) 2 ( 60).2 () increments up to... 8 ( 5, 486) Note: Lengths to 8 available in widths 6 to 8 only. Gang Drive Conveyors: Non-V-Guided belts up to 24 (60) wide, V-Guided belts up to 8 (457) wide ORDERING INFORMTION M D 0 02 elt Type. ee Page 42 Conveyor Profile. ee Page 40 Drive haft Position:,,C or D Conveyor Length Reference. Conveyor Width Reference. Documentation Language: M = English, U = CE English Wiper / Mounting racket: = no wiper with mounting brackets, 2 = no wiper / no mounting brackets* = end wiper with mounting brackets, 4 = end wiper / no mounting brackets* 5 = dual wiper with mounting brackets, 6 = dual wiper / no mounting brackets* Drive Option: 2 = tandard 2mm Diameter Output haft = Gang Drive Thru-haft 6200 eries Conveyor Example: 622M08000D002 Description: 6200 eries end drive conveyor with standard drive shaft in the D position, 8 (20) wide x 0 (,048) long, low side profile, general purpose belt and English documentation. Drive haft Position ince belts are being pulled, positions & D are preferred. Pushing belts ( & C) reduce conveyor load capacity by approximately 66%. *may require belt return rollers, see chart on page 60 Note: Dimensions are represented in inches, feet, and (millimeters). Due to the wide variety of drive set-ups and applications, point of installation guarding is the responsibility of the end user. 5

5 6200 ERIE: FLT ELT CENTER DRIVE 6200 pecifications: gauge stainless steel roll formed frame ealed earings elt widths:.75 (44) to 2 ( 05) Conveyor lengths: 2 (60) to 24 (7,5 ) (25) diameter head and tail pulleys The.25 (2) diameter drive pulley turns approximately 4.2 (07) of belt per revolution..5 (8) bottom of frame to top of belt 2mm diameter integral drive shaft. Loads capacity up to 20 Lbs* (54 Kg) Reversing center drive belt direction reduces load capacity by 66% elt speeds up to 264 ft/min. (8 M/min.) Metric fasteners Mild steel head and tail plates with black nitrite finish Motion sensor switch ready Models available Features/enefits: Center Drive models free up conveyor ends for machine or operator interface The Center Drive module can be easily repositioned along the length of the conveyor treamlined design fits where other conveyors do not Low maintenance sealed bearings in both head and tail pulleys Lengths in.2 (4) increments elt materials to match application requirements Quick clamp rail for easy mounting of bolt-on accessories V-Groove frame with guided belt ensures accurate tracking Durable.25 (6) thick bottom wiper Wedge-Lok ystem Center Drive Module can be positioned anywhere along the length of the conveyor Gas pring elt Tensioner constantly adjusts the belt tension and requires no shop air to operate. 6 Conveyor load capacity depends on conveyor size, incline, motor position, accumulated loads and other factors. ee Performance Charts / Data section for details. Order gearmotor mounting packages and gearmotors separately; see pages 45 & 52. For support stands and accessories, see pages 60 & 65

6 TNDRD IZE Conveyor Width Reference Conveyor elt Width (W).75 (44) 2.75 (70).75 (95) 5 (27) 6 (52) 8 (20) 0 (254) 2 (05) Conveyor Length Reference increments up to (457) Conveyor Length (L) 2 ( 60).2 () increments up to ( 7, 5) Note: Lengths to 8 available in widths 6 to 8 only. ORDERING INFORMTION 65 2 M elt Type. ee Page 42 Conveyor Profile. ee Page 67 Drive haft Position: or D Conveyor Length Reference. Conveyor Width Reference. Documentation Language: M = English, U = CE English Wiper / Mounting racket: = no wiper with mounting brackets, 2 = no wiper / no mounting brackets* = end wiper with mounting brackets, 4 = end wiper / no mounting brackets* 5 = dual wiper with mounting brackets, 6 = dual wiper / no mounting brackets* 6200 eries Center Drive Conveyor Example: 652M08000D002 Description: 6200 eries center drive conveyor with standard drive shaft in the D position, 8 (20) wide x 0 (,048) long, low side profile, general purpose belt and English documentation. Drive haft Position Reversing elt Direction Reduces load capacity by 66% *may require belt return rollers, see chart on page 60 Note: Dimensions are represented in inches, feet, and (millimeters). Due to the wide variety of drive set-ups and applications, point of installation guarding is the responsibility of the end user. 7

7 6200 ERIE: CLETED ELT END DRIVE 6200 pecifications: gauge stainless steel roll formed frame ealed bearings elt widths:.75 (44) to 8 (457) Conveyor lengths: 2 (60) to 8 (8,486).5 (8) bottom of frame to top of belt 2mm diameter integral drive shaft The (25) diameter drive pulley turns approximately.4 (86) of belt per revolution Load capacity up to 80 Lbs* (6 Kg) elt speeds up to 255 ft/min. (78 M/min) Cleats available from.24 (6) to 2.6 (60) high Metric fasteners Mild steel head and tail plates with black nitrite finish Motion sensor switch ready Models available Features/enefits: Wedge-Lok system for impact protection treamlined design fits where other conveyors do not Quick 5 minute belt change for increased uptime Low maintenance sealed bearings in both head and tail spindles Lengths in.2 (4) increments Quick clamp rail for easy mounting of bolt-on accessories Rack and pinion design offers fast single point belt tensioning V-Groove frame with guided belt ensures accurate tracking variety of cleat heights to meet application needs Wedge-Lok ystem Flat elt & Cleated elt End Drive Conveyors feature a quick 5 minute belt change. Loosen fasteners and collapse tail section. Remove old belt and replace. djust tension on new belt, tighten fasteners and go! 8 Conveyor load capacity depends on conveyor size, incline, motor position, accumulated loads and other factors. ee Performance Charts / Data section for details. Order gearmotor mounting packages and gearmotors separately; see pages 45 & 52. For support stands and accessories, see pages 60 & 65

8 W = Conveyor elt Width TNDRD IZE Conveyor Width Reference Conveyor elt Width (W).75 (44) 2.75 (70).75 (95) 5 (27) 6 (52) 8 (20) 0 (254) 2 (05) Conveyor Length Reference increments up to (457) Conveyor Length (L) 2 ( 60).2 () increments up to... 8 ( 5, 486) Note: Lengths to 8 available in widths 6 to 8 only. Cleat types and spacing limited on conveyors onger than 2 due to belt weight ORDERING INFORMTION 6 M D 060 Cleat pacing, ee Page 44 Drive haft Position: or D Conveyor Length Reference. Conveyor Width Reference. Documentation Language: M = English, U = CE English Mounting racket: = with mounting brackets 2 = without mounting brackets* Cleat Type. ee Chart on Page Cleated elt Conveyor Example: 6M08000D060 Description: 6200 eries cleated belt end drive conveyor with standard drive shaft in the D position, 8 (20) wide x 0 (,048) long, low side profile, general purpose belt and English documentation. Drive haft Position ince belts are being pulled, positions & D are preferred. Pushing belts ( & C) reduce conveyor load capacity by approximately 66%. *may require belt return rollers, see chart on page 60 Note: Dimensions are represented in inches, feet, and (millimeters). Due to the wide variety of drive set-ups and applications, point of installation guarding is the responsibility of the end user. 9

9 400 & 6200 ERIE: PROFILE 400 eries Profiles W +.50 ().50 (8) W 2.00 (5) W 2.06 (52) W -.62 (6) -0 Low ide -02 igh ide -0* ide Wiper 2.06 (52) W +.62 (6) W -.40 (0) 2.00 (5) W -.22 (6) -07* Low ide To ide Wiper -09 Low ide To igh ide * = Do not use with igh Friction elts W = Conveyor elt Width ORDERING INFORMTION Example: /02 Description: 400 eries End Drive Conveyor 2 (44) wide x (94) long with hex broach located in the position, high side profile and general purpose belt. Dimensions are represented in inches, and (millimeters). Due to the wide variety of drive set-ups and applications, point of installation guarding is the responsibility of the end user. 40

10 PROFILE 6200 eries Profiles.50 (8) W+.25 (6) W+.57 (5) * * = Do not use with igh Friction elts W = Conveyor elt Width ORDERING INFORMTION Example: 622M08000D002 Description: 6200 eries end drive conveyor with standard drive shaft in the D position, 8 (20) wide x 0 (,048) long, low side profile, general purpose belt and English documentation. Dimensions are represented in inches, and (millimeters). Due to the wide variety of drive set-ups and applications, point of installation guarding is the responsibility of the end user. 4

11 400 & 6200 ERIE: TNDRD ELTING tandard elt election Guide tandard belt material is stocked at Dorner, then cut & spliced at the factory for fast conveyor shipment. elt Type - Finger plice elt Type - Plastic Clipper elt Type - Metal Clipper elt pecifications Thickness urface Material Carcass Material Maximum Part Temp. Coefficient of Friction FD pproved nti-tatic tatic Conductive Chemical Resistant pecial Characteristics or pplications 0 FD ccumulation.06 (.6) Urethane Polyester 76 F (80 C) Low x x Good Packaging, clean room & inspection General Purpose.07 (.8) Urethane Polyester 22 F (00 C) Med x x Good Most versatile belt offering 0 FD igh Friction.06 (.6) Urethane Polyester 76 F (80 C) igh x x Good Packaging, clean room & inspection ccumulation.047 (.2) Urethane Polyester 22 F (00 C) V-Low x x Good ccumulation of products 06 6 Electrically Conductive.06 (.6) Urethane Polyester 20 F (0 C) Low x x Good Electronics andling igh Friction.08 (2.) PVC Polyester 58 F (70 C) V-igh x Poor Conveys up to 5 inclines* Note: ee below for splice details. Plastic Clipper splice requires longer lead times. No Metal Clipper plice on belts over 2 (05) wide. *Incline varies due to factors like dust, fluids and part material. elt plicing Finger plice ll belts are available with a standard Thermoformed finger splice. This splice makes the belt continuous and is virtually undetectable. plice bonding methods vary by belt type. Consult factory for details. 42 Plastic Clipper* n optional plastic clipper splice is available for quick removal of belts or when conveyors are installed in tight spaces. The clipper does not protrude above the belt surface. Metal Clipper* n optional metal clipper splice is also available for quick removal of belts or when conveyors are installed in tight spaces. *ee belt charts for compatibility. Not for use with 400 ereis, 6200 eries Gang Drive or 6200 ereis with bottom wiper.

12 PECILTY ELTING pecialty elt election Guide pecialty belt material is not stocked at Dorner and needs to be custom ordered for your special conveyor needs. elt Type with Finger plice elt Type with Plastic Clipper elt Type with Metal Clipper 400 eries 6200 eries elt pecifications elt Thickness urface Material Maximum Part Temp. Coefficient of Friction FD pproved Chemical Resistance pecial Characteristics or pplications 50 X eat Resistant.05 (.) ilicone 56 F (80 C) Low Good 5 X Translucent & Nosebar, ccumulation.02 (.5) Urethane 22 F (00 C) V-Low x Good ack Lit inspection & Very mall Product Transfer 54 F4 4F X X FD ealed Edge.06 (.5) Urethane 76 F (80 C) Low x Good Packaging, clean room & inspection 55 F5 5F X X FD ealed Edge.06 (.5) Urethane 76 F (80 C) igh x Good Packaging, clean room & inspection 56 6F X X Cut Resistant.08 (2.) Urethane 22 F (00 C) Med. Good Oily product release, Metal stamping 57 7F X X Cut Resistant.0 (2.5) Nitrile 76 F (80 C) Med. Poor Felt-like, dry metal stamping, glass & ceramic 58 8F X Cut Resistant.06 (.5) Urethane 76 F (80 C) Low V-Good Cross-linked surface, Gold colored 59 F9 9F X X Color Contrasting.06 (.5) PVC 58 F (70 C) Med. Poor lack colored, hides overspray from ink jet 60 G0 0G X X Color Contrasting.06 (.6) Urethane 76 F (80 C) Low x Good Green colored 6 G G X X Color Contrasting.05 (.2) Urethane 22 F (00 C) Med. x Good lue colored 6 G X X Electrically Conductive.05 (.2) Urethane 40 F (60 C) Low Good tatic conductive, electronics handling 64 4G X igh Friction.7 (4.4) PVC 94 F (90 C) V-igh Poor Dark Green colored, rough top surface, product cushioning, incline / decline apps 65 5G X Chemical Resistant.05 (.) Polypropylene 250 F (26 C) Low x V-Good V-Good Cut resistance, excellent product release 66 6G X X Chemical Resistant.07 (.7) Polyester 22 F (00 C) Med. x V-Good Good Cut resistance, metal stamping apps 67 7G X Low Friction Cleated.06 (.6) Polyester 22 F (00 C) n/a x Good Note: Plastic Clipper splice requires longer lead times. No Metal Clipper plice on belts over 2 (05) wide. * Do not use with LPZ conveyor. ** 2 (05) wide conveyor maximum. *** Not available in 2 (5) wide. 24 (60) wide conveyor maximum Excellent product release, consult factory for part number and how to specify low friction ORDERING INFORMTION: tandard Flat & pecialty elt Example: 220M Description: 2200 eries End Drive Conveyor, 2 (5) wide x (94) long with output shaft located in the position, standard low sides, general purpose belt and English documentation. 4

13 400 & 6200 ERIE: TNDRD CLETED ELTING * * C* F** G** * V* J* * = Maximum 7 conveyor length for 8 and wider conveyors ** = Maximum 20 (508) cleat spacing for 7 and longer conveyors ase elt Material:.055 (.4) thick, high friction FD approved urethane, 76 F (80 C) maximum part temperature. ee pecialty elt 67 for low friction base belt material. Note: Minimum cleat spacing is approximately 2 (50). Consult Factory. Cleated belts are not available on 400 eries Conveyors. x x-.7 (4) Tolerance + _.08 (2) CLET PCING teps: ) Refer to Formulas below. 2) Use formula to determine the approximate number of cleats required based upon the desired cleat spacing. ince a partial cleat cannot be used, round the number of cleats up or down. ) Use formula 2 to get the cleat space reference for the conveyor part number. Formula Number of Cleats = (Conveyor Length in feet x 24) +.7 Desired cleat spacing in inches (x) Example Using a 6 long conveyor and 6 cleat spacing Number of Cleats = (6 x 24) +.7 = 45 = 24 Cleats 6 6 (rounded) Formula 2 Cleat pace Reference (x) = (Conveyor length in feet x 24) +.7 Number of Cleats from Formula Example Using a 6 long conveyor and 24 cleats Cleat pacing in Inches (x) = (6 x 24) +.7 = 45 = 6.04 or 0604 Cleat 24 cleats 24 Reference W-.00 (25) (Pocket Width) ORDERING INFORMTION Example: 2240M0806D0604 Description: 2200 eries Cleated elt Conveyor 8 (20) wide x 6 (,829) long with hex shaft located in position D, Type cleats spaced on 6.04 (5) centers and English documentation. W+.79 (20) Z Z = 2.68" (68) for, F, G & Cleats 4.04" (02) for, C, V & J Cleats W = Conveyor elt Width 44

14 GERMOTOR MOUNTING PCKGE Gearmotor Mounting Package & Gearmotor election teps tep : elect a Gearmotor Mounting Package. For End drive conveyors, select a side, bottom, top or gang drive mount (pages 46-49). If a Center Drive conveyor is being outfitted, refer to the Center Drive section pages 50 & 5. e sure to note if it is for a 90 or Parallel haft Gearmotor. tep 2: Using elt peed & Load Requirements, determine the required Gearmotor Type (Light, eavy or tandard) for your application using the chart below. tep : Find the appropriate set of elt peed Charts (pages 48 & 5) for the Mounting Package you selected and choose between the Fixed or Variable peed chart. tep 4: Go down the first column of the elt peed Chart and locate the required elt peed for your application. If the desired belt speed is not listed, round up to the next higher speed. (Dorner offers much more than just the belt speeds listed in the tables, contact the factory for complete details) tep 5: From the row containing your required elt peed, check to be sure that speed is available for the Mount Package you chose. (End Drive Only - Top, ottom or ide) tep 6: Use the Drive / Driven Pulley Kit combination to complete your Mounting Package tep 7: Note the RPM from Gearmotor, it will be needed to select the correct Gearmotor from the Gearmotor Chart. tep 8: Reference the Gearmotor Chart # to locate a compatible Gearmotor Chart on Pages e sure to select a Gearmotor Chart to match your Gearmotor Type (Light, tandard or eavy) and your Mounting Package while meeting your electrical requirements. (Red = Parallel haft or lue = 90 ) tep 9: Using the RPM from Gearmotor (tep 6), locate the for your Gearmotor from the Gearmotor Table. elt peed - Ft/min (M/min) GERMOTOR TYPE Light Load tandard Load eavy Load 0-5 (0-4.6) 6-0 (4.9-9.) -45 (9.5-.7) (4-8.) 6-75 ( ) ( ) 9-0 ( ) -0 (.8-9.6) -50 ( ) 5-75 (46-5.4) (5.7-6) ( ) ( ) ( ) Conveyor Load - Lbs (Kg) 0 (4.5) 20 (9.) 0 (.6) 40 (8.2) 50 (22.7) 60 (27.) 70 (.8) 80 (6.4) 90 (40.9) 00 (45.5) 0 (50) 20 (54.5) ORDERING INFORMTION: End Drive Mounting Packages 6 M P Drive / Driven Pulley Combination: ee elt peed charts, Pages 48 & 5 (Top and ottom mounts only) elt tyle: - = Flat elt or add Cleat Type:,, C, F, G,, J, V Gearmotor Mounting Position:,, C, D. Conveyor Width Reference: ee Conveyor ection. Gearmotor Type: ee Gearmotor charts, Page L, V,, Gearmotor Output haft: ee Gearmotor charts, Page P = Parallel haft or = 90 Mount tyle: = ide Mount, = ottom Mount, T = Top Mount Documentation Language: M = English, G = CE German, U = CE English Conveyor eries: Example: 6MP = 400 End Drive 6 = 6200 End Drive (non-gang Drive) Drive haft Position ince belts are being pulled, positions & D are preferred. Pushing belts ( & C) reduce conveyor load capacity by approximately 66%. Description: ottom mount package with English documentation for 6 (52) wide 6200 series end drive conveyor. Configured for a parallel shaft, tandard load motor in the mount position with a 28:28 drive / driven pulley combination. 45

15 400 & 6200 ERIE: END DRIVE MOUNTING PCKGE ide Mount Package, 90 Gearmotor 6.8 (72) 9.2 (24) 5.2 (2) W 2.2 (56) 4. (62) 5. ().6 (4) tandard load gearmotors only Includes : Gearmotor mounting bracket, coupling, coupling guard & mounting hardware W = Conveyor elt Width ottom Mount Package, 90 Gearmotor 2.0 (52) 0. (8) W 0.7 (7) 9.2 (24) : tandard Load Flat elt = 5.2 (2) : tandard Load Flat elt = 4.6 (7) tandard Load Cleated elt = 7.9 (99) tandard Load Cleated elt = 4.6 (7) eavy Load Flat elt = 7.9 (99) eavy Load Flat elt = 5.6 (95) eavy Load Cleated elt = 7.9 (99) eavy Load Cleated elt = 5.6 (95) Includes : Gearmotor mounting bracket, coupling, coupling guard & mounting hardware W = Conveyor elt Width.4 (87) 4.5 (5) 0.7 (7) Top Mount Package, 90 Gearmotor.4 (87) 2.0(52) C 0.(8).8(46) 4.5 (5) W 0.7(7) : tandard Load =.8 (96) : tandard Load = 4.6 (7) C: tandard Load =. (28) eavy Load =.4 (86) eavy Load = 5.6 (95) eavy Load =.8 (0) Includes : Gearmotor mounting bracket, coupling, coupling guard & mounting hardware W = Conveyor elt Width 90 tandard Load Gearmotor Location Options Notes: Position recommended. Vertical positions 2 & 4 may require additional stabilizing bracket. Consult factory for details ee pages for Gearmotor election 46 Note: Conveyor and gearmotor are not included in the mounting package and must be ordered separately. Dimensions are represented in inches and (millimeters)

16 END DRIVE MOUNTING PCKGE ide Mount Package, Parallel haft Gearmotor 2. (52).2 (8) W.7 (44) 6. (55).2 (8) 0.6 (5) : Light Load, Fixed peed = 4.6 (7) Light Load, Variable peed = 6.7 (70) Light Load CE Fixed peed = 7.2 (8) Light load gearmotors only Includes : Gearmotor mounting bracket, coupling, coupling guard & mounting hardware W = Conveyor elt Width ottom Mount Package, Parallel haft Gearmotor 2. (59) W 0.6 (6).7 (94) 6.4 (6) D 2.6 (67) C 0.6 (6) : Light Load Flat elt = 6.9 (75) C: Light Load Flat elt = 6.7 (70) Light Load Cleated elt = 8.9 (226) Light Load Cleated elt = 6.7 (70) tandard Load Flat elt = 9.2 (24) tandard Load Flat elt = (267) tandard Load Cleated elt = 9.2 (24) tandard Load Cleated elt = (267) : Light Load Flat elt = 6.2 (58) D: Light Load Flat elt = 6. (55) Light Load Cleated elt = 8. (2) Light Load Cleated elt = 5.6 (42) tandard Load Flat elt = 8.5 (26) tandard Load Flat elt = 4.6 (6) tandard Load Cleated elt = 0. (262) tandard Load Cleated elt = 4.6 (6) Includes : Gearmotor mounting bracket, coupling, coupling guard & mounting hardware W = Conveyor elt Width Top Mount Package, Parallel haft Gearmotor 2.6 (67) C 2. (59) W.8 (46) 6. (55) D 0.6 (6) : Light Load = 8.9 (226) C: Light Load = 6.7 (70) tandard Load = 9.2 (24) tandard Load = (267) : Light Load =. (84) D: Light Load = 5.6 (42) tandard Load = 4. (0) tandard Load = 4.6 (6) Includes : Gearmotor mounting bracket, coupling, coupling guard & mounting hardware W = Conveyor elt Width 47

17 400 & 6200 ERIE: END & GNG DRIVE ELT PEED CRT Refer to the Gearmotor election teps on Page 45 for instructions on using the elt peed Charts. Fixed peed elt peed Ft/min M/min RPM From Gearmotor Mount Package Pulley Kit Gearmotor Chart # Top & ottom ide Drive Pulley Driven Pulley Light Load tandard Load X X X eavy Load X 9 2 4, 5 2, X X , 5 2, X X X X X , X , 5 2, X X , X X X , 5 2, X X X , 5 2, X X X , 5 2, X , 5 2, X , 5 2, X X , 5 2, X , 5 2, X , 5 2, X , 5 2, X , 5 2, X , 5 2, Gearmotor RPM at 50 z 5.5 2* X * X X * X X * X * X * X X * X * X X * X X * X * X X * X * X * X * X * X * X Variable peed elt peed Ft/min M/min RPM From Gearmotor Mount Package Pulley Kit Gearmotor Chart # Top & ottom ide Drive Pulley Driven Pulley Light Load tandard Load X X eavy Load X 9 2 8, 5, X , 5, X X , X , X X X X X , 5, X X , X X X , 5, X X X , X , 5, X , 5, X , X X , X , 5, X , 0 4 RPM from CE/50 z gearmotors VFD drive at 6 Max. z. output * X * X X * X X * X X * X X * X * X X * X * X Note: Red = Parallel haft, lue = 90 48

18 GNG DRIVE MOUNTING PCKGE.50 (8) olster Plate.88 (5).25 (2).8 (86) MIN. Gang Drive Pulleys require periodic greasing 50.0 (,270) MX..9 (2) Includes: Motor mounting bracket, 4 (29mm) hex shaft, coupling, shaft guard, support block, and support block bracket. - Components included with single output shaft assembly. - dditional components included with double output shaft assembly. ORDERING INFORMTION Notes: Conveyors cannot be secured to bolster plate Order conveyor with gang drive option separately Order gearmotor separately (90 tandard & eavy Load only) Positions 2 & recommended 6 M 0 0 = ingle Output haft 0 = Double Output haft Documentation Language M = English, U = CE English Example: 6M0 Description: Gang drive mounting package with English documentation. Common Drive et-up Includes mounting structure, drive shaft, shaft guard and conveyor mounting hardware. Order gearmotor & gearmotor mounting package separately Consult factory with conveyor and spacing details Conveyors are secured to sub-structure at fixed centerline locations Common drive setups can be customized to your exact specifications. Just provide the conveyor widths, lengths, quantity and centerline spacing. vailable with top, bottom or side mount packages for standard or heavy load gearmotors. Consult factory with details. Due to the wide variety of possible conveyor setups, adaption of the supplied guarding material is the responsibility of the end user. 49

19 400 & 6200 ERIE: CENTER DRIVE MOUNTING PCKGE TYPE - Verticle Mount TYPE 2 - orizontal Mount Parallel haft Gearmotor Parallel haft Gearmotor 90 Gearmotor 90 Gearmotor TYPE 2 recommended for tight spaces and allows for easy access to the drive modual. * Gearmotor not included in mounting package, see pages 52 for gearmotor ordering information. Note: Dimensions are represented in inches, feet, and (millimeters). ORDERING INFORMTION: Center Drive Mounting 22 M 2 P Drive / Driven Pulley Combination: ee elt peed Charts, Page 5 Mount Position: or D Conveyor Width Reference: ee Conveyor ection Gearmotor Type: ee Gearmotor charts. Page 52-57,. Gearmotor Output haft: ee Gearmotor charts. Page P = Parallel haft = 90 Mount tyle: = Type, Vertical Mount 2 = Type 2, orizontal Mount Documentation Language: M = English G = CE German U = CE English Conveyor eries: 22 = 2200 Center Drive Example: 22M2P06-22 Drive haft Position Reversing elt Direction reduces conveyor load capacity by 66%. Description: 2200 eries orizontal Center Drive Mounting Package with English documentation for a parallel shaft standard load gearmotor mounted in the position, with a 2:2 drive / driven pulley combination, on a 6 (52) wide conveyor. 50

20 CENTER DRIVE ELT PEED CRT Refer to the Gearmotor election teps on Page 45 for instructions on using the elt peed Charts. Fixed peed elt peed Ft/min M/min RPM From Gearmotor Drive Pulley Pulley Kit Gearmotor Chart # Driven Pulley tandard Load eavy Load , 5 2, , 5 2, , , , 5 2, , 5 2, , 5 2, , 5 2, , 5 2, , 5 2, , 5 2, , 5 2, Gearmotor RPM at 50 z Note: Red = Parallel haft, lue = 90 Variable peed elt peed Ft/min M/min RPM From Gearmotor Drive Pulley Pulley Kit Gearmotor Chart # Driven Pulley tandard Load eavy Load , 5, , , 5, , , , 5, , , 5, , , 5, , 5, , , , 5, , , 5, , 0 4 RPM from 50 z. gearmotors, VFD drive at 6 max. z. output

21 400 & 6200 ERIE: GERMOTOR Gearmotor election teps Refer to page 45 for directions on electing a Gearmotor Mounting Package and Gearmotor. GERMOTOR TYPE Light Load tandard Load eavy Load Conveyor Load - Lbs (Kg) 0 (4.5) 20 (9.) 0 (.6) 40 (8.2) 50 (22.7) 60 (27.) 70 (.8) 80 (6.4) 90 (40.9) 00 (45.5) 0 (50) 20 (54.5) elt peed - Ft/min (M/min) 0-5 (0-4.6) 6-0 (4.9-9.) -45 (9.5-.7) (4-8.) 6-75 ( ) ( ) 9-0 ( ) -0 (.8-9.6) -50 ( ) 5-75 (46-5.4) (5.7-6) ( ) ( ) ( ) Gearmotor ccessories 90 Gearmotor eat ink 5.4 (8) 5.25 () 2.80 (7) Reduces gear head surface temperature by up to 50 F (0 C) Compatible with tandard and eavy Load 90 Gearmotors lack anodized aluminum Description Gearmotor eat ink 52

22 GERMOTOR Light Load, Fixed peed Chart Parallel haft ealed Gearmotor Totally enclosed, Non-ventilated. Includes witch, Cord & Overload Protection 5V, Phase Non-reversing 60 z 5.4 (8).5 (80) 2.89 (7).5 (80).9 (2).8 Ø 6.92 (76) 6.05 (54).26 (2) 5.87 (49).05 (27) RPM Gearmotor Type Ph p Ph Kw Ph FL in-lbs N-m 62M06PL4F(N) 62M05PL4F(N) (n) = Reversing capability. N = No reversing switch. R = With reversing switch. L L Chart 2 Parallel haft Totally enclosed, Fan Cooled IP44 Protection Rating Non-reversing 50 z Order starter separately, ee page () 2.5 (6) 2 mm Ø 8.8 (224).0 (25).2 (80) RPM Gearmotor Type Ph Kw Ph FL Ph Kw Ph FL N-m tarter Chart 62Z028PL42FN 62Z028PL4(vp)FN 62Z008PL42FN 62Z008PL4(vp)FN (vp) = Voltage and Phase 2 = 20V, phase 4 = 400V, phase L L L L n/a n/a 0. n/a 0. n/a n/a n/a n/a.22/. n/a.22/ Note: When buying a gearmotor only without the starter, the customer must supply their own on/off switch and motor overload protection to comply with the CE afety Directive. Light Load, Variable peed Chart Parallel haft 0 Volts DC ealed Gearmotor Totally enclosed, Non-ventilated RPM motor Order controller separately, ee page 58.7 (4).4 (86).4 (86).0 (25).5 Ø 9.4 (28).6 (40) 2.9 (7) 2.4 (6) RPM Gearmotor Type p Kw FL in-lbs N-m Vari - peed Control Chart 62M060PLDDEN 62M08PLDDEN 42 9 V V FL = Full Load mperes Note: 8 (20 ) and wider conveyors with light load drives should be limited to 8 (2,48) long. ome motors & gear reducers may normally operate hot to the touch. Consult factory for specific operating temperatures. 5

23 400 & 6200 ERIE: GERMOTOR tandard Load, Fixed peed Chart 4 90 ealed Gearmotor NEM 42 CZ C Face Totally enclosed, Fan cooled 5V phase includes switch, Cord & Overload protection /460V phase wiring by others 60 z Order phase starter separately, ee page (64).4 (5) 6.6 (68) 2.8 (70) 5.2 () 2.2 (56) 2.9 (74). (4) 4. (62) 5. () 5. () RPM Gearmotor Type Ph p Ph Kw Ph FL Ph p Ph Kw Ph FL in-lbs N-m Phase tarter Chart 2M060L4(vp)F(n) 2M040L4(vp)F(n) 2M020L4(vp)F(n) 2M00L4(vp)F(n) 2M005L4(vp)F(n) (vp) = Voltage and Phase (n) = Reversing Capability = 5V, phase N = No reversing switch. 2 = / 460V, phase R = With reversing switch (5V, phase only) /0.6.2/0.6.2/0.6.2/0.6.2/ L L L L L Chart 5 Parallel haft ealed Gearmotors Totally enclosed, Fan cooled 5V phase includes switch, Cord & Overload protection 20V phase wiring by others 60 z Order phase starter separately, ee page (8) 4.75 (2) 2.9 (6) 2.04 (52) 6.7 (7) 2.62 (67).75 Ø 2.00 (5).00 (28) 4.75 (2) 62M80P4(vp)F(n) 62M060P4(vp)F(n) 62M00P4(vp)F(n) 62M020P4(vp)F(n) 62M00P4(vp)F(n) 62M005P4(vp)F(n) RPM Gearmotor Type Phase Phase p Kw FL in-lbs p Kw FL in-lbs (vp) = Voltage and Phase (n) = Reversing Capability = 5V, phase N = No reversing switch. 2 = 20V, phase R = With reversing switch (5V, phase only) N-m Phase tarter Chart L L M M M M Chart 6 90 ealed Gearmotor IEC 6 5 C Face IP 55 Protection Rating Totally enclosed, Fan cooled Non-reversing 50 z Order starter separately, ee page 59 RPM Gearmotor Type 62Z0604(vp)FN 62Z0404(vp)FN 62Z0204(vp)FN 62Z004(vp)FN 62Z0054(vp)FN (vp) = Voltage and Phase 2 = 20V, phase 2 = 20,, phase 4 = 400V, phase Ph Kw (44) 6.6 (68) 5.5 (40) Ph FL (70) 4.9 (24) 2.9 (74).4 (5) Ph Kw (56). (4) Ph FL.4/.8.4/.8.4/.8.4/.8.4/.8.4 (9) 5.9 (49) N-m tarter Chart Note: When buying a gearmotor only without the starter, the customer must supply their own on/off switch and motor overload protection to comply with the CE afety Directive. I I I I I 54 FL = Full Load mperes ome motors & gear reducers may normally operate hot to the touch. Consult factory for specific operating temperatures.

24 GERMOTOR tandard Load, Variable peed Chart Volts DC ealed Gearmotor NEM 42 CZ C Face Totally enclosed, Fan cooled RPM motor Order controller separately, ee page 58 RPM Gearmotor Type p Kw FL in-lbs N-m Vari - peed Control Chart 22M060DDEN 22M040DDEN 22M020DDEN 22M00DDEN 22M005DDEN Chart 8 90 Variable frequency Drive, 6-60 z ealed Gearmotor NEM 56C C Face Totally enclosed, Fan cooled 20/460 Volts, phase Order controller separately, ee page (68).4 (5) 6.6 (68) 7.6 (94) 2.9 (74) 2.2 (56). (4) 5.9 (49) 2.9 (27) RPM Gearmotor Type p Kw FL in-lbs N-m Vari - peed Control Chart 2M060L42EN 2M040L42EN 2M020L42EN 2M00L42EN 2M005L42EN * = t 60 z /.97.6 /.97.6 /.97.6 /.97.6 / D and E D and E D and E D and E D and E Chart 9 90 Variable Frequency Drive, 25-6 z ealed Gearmotor IEC 6 5 C Face IP 55 Protection Rating Totally enclosed, Fan cooled 20V, phase Order controller separately, ee page 58 RPM* 62Z06042EN 62Z04042EN 62Z02042EN 62Z0042EN 62Z00542EN * = t 50 z Gearmotor Type Ph Kw Ph FL N-m* Vari - peed Note: When buying a gearmotor only without the starter, the customer must supply their own on/off switch and motor overload protection to comply with the CE afety Directive. ome motors & gear reducers may normally operate hot to the touch. Consult factory for specific operating temperatures. FL = Full Load mperes 55

25 400 & 6200 ERIE: GERMOTOR tandard Load, Variable peed Chart 0 Parallel haft 0 Volts DC ealed Gearmotor Totally enclosed, Non-ventilated RPM motor Order controller separately, ee page (62) 4.9 (24).5 (7) 4.8 (2).75 Ø 2.5 (8) 2.0 (5) 4. (08) RPM Gearmotor Type p Kw FL in-lbs N-m Vari - peed Control Chart 62M80PDDEN 62M060PDDEN 62M00PDDEN 62M020PDDEN 62M00PDDEN 62M005PDDEN Chart Parallel haft Variable frequency drive, 0 to 60 z ealed Gearmotor Totally enclosed, Fan cooled 20 Volts / Phase, VFD duty Order controller separately, ee page (8) 4.75 (2) 2.9 (6) 2.04 (52) 6.7 (7) 2.62 (67).75 Ø 2.00 (5).00 (28) 4.75 (2) *RPM Gearmotor Type p Kw FL in-lbs N-m Vari - peed Control Chart 62M80P42EN 62M060P42EN 62M00P42EN 62M020P42EN 62M00P42EN 62M005P42EN * = t 60 z D and E D and E D and E D and E D and E D and E eavy Load, Fixed peed Chart 2 90 ealed Gearmotor NEM 56 C Face Totally enclosed, Fan cooled 5V phase includes switch, Cord & Overload protection /460V phase wiring by others 60 z Order phase starter separately, ee page 59.4 (5) 7.7 (96) 7.7 (96) 6.6 (68) 2.8 (70) 6.6 (68) 2.2 (56) 2.9. (74) (4) 5.9 (49) 5.2 (86) 6.2 (57) RPM Gearmotor Type Ph p Ph Kw Ph FL Ph p Ph Kw Ph FL in-lbs N-m Phase tarter Chart 2M0604(vp)F(n) 2M0404(vp)F(n) 2M0204(vp)F(n) 2M004(vp)F(n) 2M0054(vp)F(n) (vp) = Voltage and Phase (n) = Reversing Capability = 5V, phase N = No reversing switch. 2 = / 460V, phase R = With reversing switch (5V, phase only) / 2.-2/ 2.-2/ 2.-2/ 2.-2/ M M M M M 56 FL = Full Load mperes ome motors & gear reducers may normally operate hot to the touch. Consult factory for specific operating temperatures.

26 GERMOTOR eavy Load, Fixed peed Chart 90 ir Gearmotor ealed Gearmotor Nema 56 C Face Non-reversing Includes muffler, filter, regulator & lubricator Use with standard load mounting package 62M060000FN 62M040000FN 62M020000FN 62M020000FN 62M005000FN RPM** Gearmotor Type 6.6 (68). (84).4 (5) P* in-lbs ** N-m** (68) 2.2 (56) 2.9 (74). (4) (267) 5.9 (49) 6.5 (65) * = t 40 PI (2,8 bar) line pressure ** = t 725 RPM from motor, 25 CFM eavy Load, Variable peed Chart V DC ealed Gearmotor NEM 56 C Face Totally enclosed, Fan cooled RPM motor Order controller separately, ee page 58 2M060D9DEN 2M040D9DEN 2M020D9DEN 62M00D9DEN 62M005D9DEN RPM Gearmotor Type p Kw FL in-lbs N-m (68).4 (5) (95) 6.6 (68) 2.6 (67) (56) 6.6 (68) 2.9 (74) 5.9 (49). (4) (72) 5.2 () Vari - peed Control Chart C C C C C Chart 5 90 Variable Frequency Drive, 6-60 z ealed Gearmotor NEM 56 C Face Totally enclosed, Non-ventilated 20/460 Volts, Phase Order controller separately, ee page 58 RPM* Gearmotor Type 2M06042EN 2M04042EN 2M02042EN 2M0042EN 2M00542EN Ph p Ph Kw (68) 7.9 (20) 6.6 (68) Ph FL.6/.8.6/.8.6/.8.6/.8.6/.8.4 (5). (79) in-lbs* (74) 2.2 (56). (4) 5.9 (49) N-m* (65) 6. (55) Vari - peed Control Chart D and E D and E D and E D and E D and E * t 60 z Chart 6 90 Integrated motor control Variable frequency drive, 0 to 80 z Digital display with start/stop and forward/reverse keypad NEM 56 C face sealed gearmotor Totally enclosed, Fan cooled 5/20 Volts, Phase input voltage 9. (22) 8.5 (27) 7. (80).4 (5) 2.9 (7) 2.2 (56) 2.9 (74) 5.9 (49). (4) 5.8 (40) 7. (80) 2M0604EC 2M0404EC 2M0204EC 2M004EC 2M0054EC RPM* Gearmotor Type p Kw Controller mps 2.4/ / / / /6.2 in-lbs* N-m* * t 60 z FL = Full Load mperes 57

27 400 & 6200 ERIE: VRILE PEED CONTROLLER Variable peed Controllers Chart PWM DC control Nema enclosure Line cord & Motor cord On / Off switch for 62MD4 Forward / Off / Reverse switch for 62MD4R peed potentiometer Mounting hardware Input Volts Input Phase Input z Output Volts *Max mps Reversing 62MD4 62MD4R (8) 5. () 62MD (4) 4.6 (6).9 (00) 0VDC 0VDC 7. (80) 5. (5) 62MD4R (47) 5.7 (45) No Yes 5.0 (27) Chart VFD control IP 65 enclosure EMC filter peed potentiometer Mounting hardware Line cord & motor cord 8.2 (208) 62(c)V (47) 5. (0) 5.8 (46) 0.8 (27) 2.8 (72) 62ZV222C 4.7 (9) 5. (0) VFD control Chassis mount EMC filter Wiring by others Input Volts Input Phase Input z Output Volts Out Phase *Max Kw Max mps Reversing 62(c)V222 62ZV222C (c) = Electrical Configuration F = CE French Chart C PWM DC control NEM enclosure Line cord & Motor cord On / Off switch for 62MD92 & 62MD9 Forward / Off / Reverse switch for 62MD92R & 62MD9R peed potentiometer *ee FL from motor charts Mounting hardware Input Volts Input Phase Input z Output Volts *Max mps Reversing 62MD92 62MD92R 62MD9 62MD9R G = CE German U = CE Great ritain VDC 90VDC 90VDC 90VDC Note:When buying a chassis mount control, the customer must provide wiring that complies with Ce afety Directives. 62MD92 & 62MD92R MD9 & 62MD9R No Yes No Yes Yes Yes Chart D Full feature VFD control NEM 4 enclosure Digital display Keypad with tart / top, Forward / Reverse and speed variations Includes cord to motor Power to controller by others 62MV22 includes line cord to controller Mounting hardware +.0 (25) 8.9 (226) 7.9 (200) +.2 (5) *eeflfrommotorcharts Input Volts Input Phase Input z Output Volts Output Phase Max p *Output mps Reverse Width Depth 58 62MV22 62MV222 62MV2 62MV22 62MV227 62MV222 62MV227 62MV44 62MV Yes Yes Yes Yes Yes Yes Yes Yes Yes 6. (55) 6. (55) 6. (55) 6. (55) 6. (55) 4.7 (9) 6. (55) 4.7 (9) 6. (55).8 (96).8 (96) 4.4 (2) 4.4 (2) 5. (4).8 (96) 5. (4).8 (96) 4.4 (2)

28 MNUL MOTOR TRTER Variable peed Controllers Chart E VFD control Nema enclosure Line cord and Motor cord On / Off switch peed potentiometer Mounting hardware Forward / Reverse switch Input Volts Input Phase Input z Output Volts Output Phase Max p *Max mps Reversing 62MV22 62MV22R No Yes Manual Motor tarters Manual motor starts are manual electrical disconnects that provide motor overload protection and are required by the National Electric Code (NEC) for safe motor operation. Illustration Illustration IP 55 Enclosure Push buton tart / top Includes mounting hardware 7.0 (78).4 (86).7 (94) 7.0 (78).4 (86).7 (94) Chart 20V, phase includes cord, plug & starter. 20/400V, phase wiring to starter by others. Wiring between motor & starter provided when ordered together. 50 z In Volts In Phase mp Range Illustration 62(c)M2 62(c)M2 62(c)M Chart I 20V, phase includes cord, plug & starter. 20/400V, phase wiring to starter by others. Wiring between motor & starter provided when ordered together. 50 z In Volts In Phase mp Range Illustration 62(c)M2T 62(c)M2T 62(c)M4T Note: When buying a gearmotor only without the starter, the customer must supply their own on/off switch and motor overload protection to comply with NEC and CE safety directives. (c) = Electrical Configuration F = CE French G = CE German U = CE Great ritain Chart L 20/460V, phase wiring to starter by others. Wiring between motor & starter provided when ordered together. 60 z In Volts In Phase mp Range Illustration 62MM2L 62MM4L Chart M 20/460V, phase wiring to starter by others. Wiring between motor & starter provided when ordered together. 60 z In Volts In Phase mp Range Illustration 62MM2M 62MM4M

29 400 & 6200 ERIE: UPPORT TND Quantity Charts upport tand Quantity Chart Conveyor Length Number of upports 2 (60) - 4 (29) * 2 (60) - 6 (829) 2 7 (24) - 2 (658) (962) - 8 (5486) 4 9 (579) - 24 (75) 5 *End Drive Conveyors with ingle-post upport tands only. Requires the use of diagonal bracing, see page 64. eavy load gearmotors require a minimum of 2 stands to support conveyor and gearmotor package. Required Return Roller Quantity Chart max feet between return rollers Conveyor Width Flat elt Cleated elt Quanity of return rollers required = whole number result of : conveyor length in feet max distance between return rollers Example Description: 6200 flat belt 8 wide x 4 long = return rollers required 6200 eries Return Rollers Cleated elt Return Roller 2.25 (57) Flat elt Return Roller for 2 to 6 Wide Conveyors.25 (2) W+.96 (24) Description.78 (20).75 (9) Return Roller for 2200 eries, Cleated elt W+.96 (24) Description.78 (20).75 (9) Return Roller for 2200 eries 2 (44) - 6 (52) wide Flat elt conveyors Flat elt Return Roller for 8 to 48 Wide Conveyors.25 (2) ORDERING INFORMTION 4949 WW W+.96 (24).78 (20).75 (9) Conveyor width reference: 08 to 48 in 02 increments Conveyor reference: 4949 = 6200 eries Example: Description: Return Roller for a 2 (05) flat belt conveyor. 60

30 UPPORT TND 6200 eries Mounting rackets Cleated tand Mounting racket 6.65 (69) Flat elt tand Mounting racket.00 (76).47 (88).47 (88) M6-.0 W-.6 (4) 2.25 (57) M6-.0 W-.6 (4) 2.25 (57) Description tand Mounting racket, Cleated elt Conveyor Description tand Mounting racket,flat elt Conveyor Note: Conveyors can be ordered with the required number of mounting brackets. If desired, order additional mounting brackets separately. 400 eries Mounting rackets Flow toward bottom wiper lock 2.0 (76).75 (9) LLLL LLLL lock Mounting lock Kits are used to mount the conveyor to support stands. Kit includes: mounting block, keyhole slots in conveyor frame, and mounting fasteners W /4-20 Drilled & Tapped LLLL LLLL Keyhole lots allow accessories or mounting blocks to be attached directly to the bottom of the conveyor frame. Keyhole slots can be stamped anywhere in the frame bottom to meet application requirements. Mounting lock not included ORDERING INFORMTION WW - LLLL Distance from wiper end in inches Conveyor Width Reference. ee conveyor section for sizes 75 = Mounting lock Kit, 77 = Keyhole lot 400 eries lock Example: Description: 400 eries Mounting lock for 6 (52) wide conveyor, centered (76) from wiper end of the conveyor. lock 2 Example: Description: 400 eries Mounting lock for 6 (52) wide conveyor, centered.5 (85) from wiper end of the conveyor. 6

31 400 & 6200 ERIE: UPPORT TND Fixed eight upport tands Fixed Foot Model tand Width (WW) 2 (05) 2 (5) increments up to (29) Part # Reference 2 in 02 increments up to tand eight ()* 5 9 in (25) increments up to (8-48) (24-255) Part # Reference 59 in 00 increments up to Metric fasteners 4 (02) eight djustment * Dependent on stand width, stands over 42 (067) may include outriggers WW wivel Locking Caster Model tand Width (WW) 2 (05) 2 (5) increments up to (29) Part # Reference 2 in 02 increments up to tand eight ()* in (25) increments up to (508-60) ( ) Part # Reference 2024 in 00 increments up to Full width top plate on 2 wide stands only djustable eight upport tands Fixed Foot Model tand Width (WW) 2 (05) 2 (5) increments up to (29) Part # Reference 2 in 02 increments up to tand eight () * 54-72* 66-84* 78-96* (05-0) (0-8) (56-42) ( ) (48-686) (60-94) (762-29) ( ) (72-829) (676-24) (98-248) Part # Reference wivel Locking Caster Model tand Width (WW) 2 (05) 2 (5) increments up to (29) Part # Reference 2 in 02 increments up to tand eight () * 59-77* (42-457) ( ) (48-559) (5-660) (60-787) (77-04) (762-46) (94-65) ( ) Part # Reference ingle Post & Pillar upport tands Metric fasteners * Dependent on stand width, stands over 42 (067) tall may include outriggers WW Full width top plate on 2 wide stands only WW WW TNDRD IZE tand Width (WW) (44) (70) (95) (27) (52) (20) (254) (05) (56) (406) (457) ingle Post upport tand D Pillar tand (must be secured to floor) Part# Reference tand eight () ( ) (60-864) (8-067) (06-270) (29-47) Part# Reference ase Diameter (D) 24 (60) 27 (686) 0 (762) (88) 6 (95) Casters do not change overall height Metric fasteners hort upport tands 62 Fixed Foot Model tand Width (WW) 2 (05) 2 (5) increments up to (29) Part # Reference 2 in 02 increments up to tand eight () in (25) increments up to (52-20) (05-56) Part # Reference 0608 in 00 increments up to 24 wivel Locking Caster Model tand Width (WW) 2 (05) 2 (5) increments up to (29) Part # Reference 2 in 02 increments up to tand eight () in (25) increments up to (279-0) (42-48) Part # Reference in 00 increments up to WW (2) WW Full width top plate on 2 wide stands only

32 UPPORT TND Fully djustable upport tands Fixed Foot Model tand Width (WW).75 (44) 2.75 (70).75 (95) 5 (27) 6 (52) 2 (5) increments up to (29) tand Width Reference increments up to Top Of elt Range (79-48) (05-787) (05-097) (05-97) (05-702) tand eight Reference wivel Locking Caster Model tand Width (WW).75 (44) 2.75 (70).75 (95) 5 (27) 6 (52) 2 (5) increments up to (29) tand Width Reference In 02 increments up to Top Of elt Range (05-48) (42-787) (42-097) (42-97) (42-702) tand eight Reference WW (24) WW Metric fasteners Multi Tier tands WW (208) Minimum Tier eight Per Conveyor 2200 Flat elt 2 (05) 2200 Cleated elt 5 (8) WW WW (208) ase Full width top plate on 2 wide stands only WW Tier ase tand Width (WW) 2 (05) 2 (5) increments up to (29) Part # Reference 2 02 increments up to tand eight () 2 (05) 2 (5) increments up to (524) Part # Reference increments up to Tier tand Width (WW) 2 (05) 2 (5) increments up to (29) Part # Reference 2 02 ncrements up to tand eight () 2 (05) (25) increments up to... 6 (94) Part # Reference increments up to Note: Do not use with support stands equipped with casters. upport tands must be anchored to the floor. Do not use if conveyed product overhangs the edge of the conveyor belt due to pinch point created. ORDERING INFORMTION 9 M T T W W - (min) (max) F ssembly (not available for pillar, single post, tall & multi tier stands) P partially assembled tandard assembly (some parts may be separate to accomodate shipping) Feet or Casters (not available for multi tier stands) F fixed foot pad C total lock swivel caster eight Reference refer to stand tables top of leg for multi tier Width Reference refer to stand tables tand Type L short stand F fixed height adjustable height F fully adjustable T multi tier stand base T2 multi tier stand tier FT tall fixed* T tall adjustable* P single post P pillar support Documentation Language M U English tand tyle 2-legged stand 4 ingle post or pillar style EXMPLE: 9M2-226CP *Tall stands are required when the stand width is.5 times the stand height. Note: Due to the wide variety of conveyor and stand options along with possible configurations, stability is final setup of the responsibility of the end user. 6

33 400 & 6200 ERIE: UPPORT TND CCEORIE tand ccessories djustable Tie racket. () L +.9 (48).28 (7) Diameter. () L.0 (25) 0.9 (2) Compatible with steel and aluminum support stands. ecure critical stand and conveyor locations. Length (L) adjusts + 0, -.25 (286 mm). Includes metric mounting hardware. 27M M M M M Description djustable Tie racket, 2 (60) djustable Tie racket, (94) djustable Tie racket, 4 (,29) djustable Tie racket, 5 (,524) djustable Tie racket, 6 (,829) ottom Mount tand racket olts to 90 standard load gearmotor Includes metric mounting hardware M 6997WWM Description L racket only, for 2 to 5 wide conveyors. racket ssembly, 06 and wider 2200 conveyors. Diagonal racing (6200 eries Only) For use on steel, aluminum and single post support stands with casters. Metric fastener mounting hardware included. For use on all stands with casters and any stands over 72 (829) tall. One brace per stand for conveyors up to 24 wide (60) Two braces per stand for conveyors over 24 wide (60) Description for two-legged style stands up to 0 tall (762) for two-legged style stands over 0 tall (762) for ingle Post and Pillar stands over 0 tall (762) Common Mount Kit (6200 eries Only) *dds 2 (5) to stand height tand accessory for mounting multiple conveyors in parallel to one stand. Not for use with 400 eries - see Gang Drive Mounting Package on Page 40 ORDERING INFORMTION 9MCM ww - n n = number of conveyors per stand (6 conveyors max.) ww = width 2 in 2 increments up to 48 Tall upport tands Tall tands are the Fixed eight and djustable eight tands as shown with additional outrigger support for added stability. These outriggers are required when the height of the stand exceeds.5x its width, and they add 6 to stand width. Tall stands over 6 tall include diagonal bracing. Fine djustment Kit Provides fine height adjustment via a threaded bolt. For use with Fixed eight tands. Note: Due to the wide variety of conveyor and stand options along with possible configurations, stability of the final setup is the responsibility of the end user. Part #:

34 CCEORIE ardware ccessories Mounting Clips For easy mounting of light weight accessories. Fasteners not included. Description 45086M 6200 eries Mounting Clip tops End top Includes metric mounting hardware 4555WW Description 6200 eries End top WW = Conveyor Width Reference rackets Table Top Mounting racket.44 () W.76 (9).50 (8).4 (9) Diameter.77 (20).75 (9). () Includes metric mounting hardware Description eries Table top bracket Note: If the discharge end of conveyor is mounted over a table or similar structure, a conveyor bottom wiper must be installed to prevent against possible pinch point. Order bottom wiper separately. Note: Due to the wide variety of drive setups and applications point of installation guarding is the responsibility of the end user. 65

35 400 & 6200 ERIE: CCEORIE Drive haft ccessories upport lock Clear Cover.0 (25).50 (8) 2.5 (64).8 (5) For 400 & 6200 eries Gang Drive Conveyors Description 4- upport lock,.8 ex haft olid Coupling, ex to ex.25 (2) Includes metric set screws ex haft.0 (25) L.8" cross the flats 20064M Description olid Coupling,.8 ex to ex Description ex haft, steel, 48 (,29) long ex haft, stainless steel, 72 (,829) long Fits 400 & 6200 light load top mount and standard & heavy load top and bottom mount packages M M Description Clear cover, ordered with mounting package Clear cover, ordered separately Flexible Coupling 2.6 (67).5 (8) () Includes E set screws, ( & C) metric set screws. Description Coupling M29 2M0 2M Flexible Coupling,.50 bore x.8 hex Flexible Coupling,.6 bore x.8 hex Flexible Coupling, 2mm bore x.8 hex Flexible Coupling, 9mm bore x.8 hex Flexible Coupling, 2mm bore x 2mm bore ervice ccessories Grease dapter Tool Kit Grease leeves Description Description Description M dapter, 400 eries dapter, 6200 eries Gang Drive M Tool Kit, 400 eries Tool Kit, 6200 eries M 20099M leeve, 400 eries, traight leeve, 400 eries, 90 leeve, 6200 eries, Gang Drive traight, 90 leeve, 6200 eries, Gang Drive traight 66