*DOC-serie 52 ING.qxd :31 Pagina 3. Rodless Cylinders Series 52

Transcription

1 *DOC-serie 52 ING.qxd :31 Pagina 3 Rodless Cylinders Series 52 N E W S

2 *DOC-serie 52 ING.qxd :31 Pagina 4 52 S E R I E S News 2005 Rodless Cylinders Series 52 Double-acting, magnetic, cushioned ø25, 32, 40 The Rodless Cylinders Series 52 are available in 3 diameters, 25, 32 and 40 mm and comes in three main versions such as Basic (M), with Slide bearing (G) and with Roller bearings (R). Furthermore these three main versions are each available with either standard- or short carriage to cover a wider range of applications. A permanent magnet is assembled on the piston allowing the position to be detected by means of proximity switches positioned in grooves located on three sides on the cylinder profile. The cylinder is equipped with an end stroke cushioning which can be regulated by means of a screw located on each end cover of the cylinder. The Rodless Cylinder Series 52 is also available in versions with air supply from one side (end cover) only if needed. Three main versions, Basic, Slide bearing and Roller bearing Extra short carriage as option for all versions Possibility of feeding both chambers from one side only 001 These products are designed for industrial applications and are not suitable for sale to the general public.

3 *DOC-serie 52 ING.qxd :31 Pagina 5 News 2005 S E R I E S 52 GENERAL DATA 52M2P...52M8P... 52M2P25A 52M2P32A 52M2P40A 52M8P25A 52M8P32A 52M8P40A Piston Ø (mm) Connection G1/8 G1/8 G1/4 Cushioning length (mm) Mass at 0 mm stroke (kg) 0,88 1,40 2,41 Additional mass per 100 mm (kg) 0,30 0,39 0,52 Operating pressure (bar) 1 8 Temperature range - 10 C + 70 C Medium clean air, without lubrication* Stroke length (mm) arbitrary up to 6000 Materials If speeds exceed 1 m/s lubricated air is recommended. Al (anodized), plastic Seals: NBR, PU * If lubricated air is used, it is recommended to use ISO VG32 oil. Once applied the lubrication should never be interrupted. GENERAL DATA 52M2C...52M8C... 52M2C25A 52M2C32A 52M2C40A 52M8C25A 52M8C32A 52M8C40A Piston Ø (mm) Connection G1/8 G1/8 G1/4 Cushioning length (mm) Mass at 0 mm stroke (kg) 0,62 0,96 1,65 Additional mass per 100 mm (kg) 0,30 0,39 0,52 Operating pressure (bar) 1 8 Temperature range - 10 C + 70 C Medium clean air, without lubrication* Stroke length (mm) arbitrary up to 6000 Materials If speeds exceed 1 m/s lubricated air is recommended. Al (anodized), plastic Seals: NBR, PU * If lubricated air is used, it is recommended to use ISO VG32 oil. Once applied the lubrication should never be interrupted. GENERAL DATA 52G2P...52G8P... 52G2P25A 52G2P32A 52G2P40A 52G8P25A 52G8P32A 52G8P40A Piston Ø (mm) Connection G1/8 G1/8 G1/4 Cushioning length (mm) Mass at 0 mm stroke (kg) 1,31 2,09 3,58 Additional mass per 100 mm (kg) 0,30 0,39 0,52 Operating pressure (bar) 1 8 Temperature range - 10 C + 70 C Medium clean air, without lubrication* Stroke length (mm) arbitrary up to 6000 Materials If speeds exceed 1 m/s lubricated air is recommended. Al (anodized), plastic Seals: NBR, PU * If lubricated air is used, it is recommended to use ISO VG32 oil. Once applied the lubrication should never be interrupted. These products are designed for industrial applications and are not suitable for sale to the general public. 002

4 *DOC-serie 52 ING.qxd :31 Pagina 6 52 S E R I E S News 2005 GENERAL DATA 52G2C...52G8C... 52G2C25A 52G2C32A 52G2C40A 52G8C25A 52G8C32A 52G8C40A Piston Ø (mm) Connection G1/8 G1/8 G1/4 Cushioning length (mm) Mass at 0 mm stroke (kg) 0,88 1,35 2,30 Additional mass per 100 mm (kg) 0,30 0,39 0,52 Operating pressure (bar) 1 8 Temperature range - 10 C + 70 C Medium clean air, without lubrication* Stroke length (mm) arbitrary up to 6000 Materials If speeds exceed 1 m/s lubricated air is recommended. Al (anodized), plastic Seals: NBR, PU * If lubricated air is used, it is recommended to use ISO VG32 oil. Once applied the lubrication should never be interrupted. GENERAL DATA 52R2P...52R8P... 52R2P25A 52R2P32A 52R2P40A 52R8P25A 52R8P32A 52R8P40A Piston Ø (mm) Connection G1/8 G1/8 G1/4 Cushioning length (mm) Mass at 0 mm stroke (kg) 1,97 2,96 5,89 Additional mass per 100 mm (kg) 0,42 0,48 0,74 Operating pressure (bar) 1, Temperature range - 10 C.+ 70 C Medium clean air, without lubrication* Stroke length (mm) arbitrary up to 6000 Materials If speeds exceed 1 m/s lubricated air is recommended. Al (anodized), plastic, hardened steel Seals: NBR, PU * If lubricated air is used, it is recommended to use ISO VG32 oil. Once applied the lubrication should never be interrupted. GENERAL DATA 52R2C...52R8C... 52R2C25A 52R2C32A 52R2C40A 52R8C25A 52R8C32A 52R8C40A Piston Ø (mm) Connection G1/8 G1/8 G1/4 Cushioning length (mm) Mass at 0 mm stroke (kg) 1,33 1,91 3,84 Additional mass per 100 mm (kg) 0,42 0,48 0,74 Operating pressure (bar) 1, Temperature range - 10 C + 70 C Medium clean air, without lubrication* Stroke length (mm) arbitrary up to 6000 Materials If speeds exceed 1 m/s lubricated air is recommended. Al (anodized), plastic, hardened steel Seals: NBR, PU * If lubricated air is used, it is recommended to use ISO VG32 oil. Once applied the lubrication should never be interrupted. 003 These products are designed for industrial applications and are not suitable for sale to the general public.

5 *DOC-serie 52 ING.qxd :31 Pagina 7 News 2005 S E R I E S 52 CYLINDER CODING 52M2P40A0500 SERIES OPERATION 2 = double-acting, cushioned 8 = double-acting, cushioned, with air supply from one side only LOADS AND TORQUE FORCES VERSION M = standard G = with slide bearing R = with roller bearing TYPE OF MOUNTING A = standard MATERIALS P = anodized AL profile tube, NBR and Polyurethane seals, standard carriage C = anodized AL profile, NBR and Polyurethane seals, short carriage STROKE (see table) BORE 25 mm 32 mm 40 mm Table showing the maximum permitted loads and torque forces model L (max) Ls (max) M (max) Ms (max) Mv (max) 52M2P25A/52M8P25A 270 N - 13 Nm 2,5 Nm 11 Nm 52M2C25A/52M8C25A 270 N - 8 Nm 2 Nm 7 Nm 52G2P25A/52G8P25A 580 N 580 N 23 Nm 10 Nm 23 Nm 52G2C25A/52G8C25A 340 N 340 N 9 Nm 5 Nm 9 Nm 52R2P25A/52R8P25A 850 N 1300 N 65 Nm 35 Nm 105 Nm 52R2C25A/52R8C25A 850 N 1300 N 29 Nm 35 Nm 64 Nm 52M2P32A/52M8P32A 300 N - 30 Nm 3 Nm 24 Nm 52M2C32A/52M8C32A 300 N - 15 Nm 3 Nm 12 Nm 52G2P32A/52G8P32A 850 N 850 N 33 Nm 15 Nm 33 Nm 52G2C32A/52G8C32A 460 N 460 N 14 Nm 6,5 Nm 14 Nm 52R2P32A/52R8P32A 900 N 1500 N 79 Nm 40 Nm 125 Nm 52R2C32A/52R8C32A 900 N 1500 N 36 Nm 40 Nm 76 Nm 52M2P40A/52M8P40A 650 N - 60 Nm 4 Nm 54 Nm 52M2C40A/52M8C40A 650 N - 30 Nm 4 Nm 27 Nm 52G2P40A/52G8P40A 1120 N 1120 N 60 Nm 25 Nm 60 Nm 52G2C40A/52G8C40A 600 N 600 N 25 Nm 11 Nm 25 Nm 52R2P40A/52R8P40A 1200 N 2000 N 190 Nm 67 Nm 118 Nm 52R2C40A/52R8C40A 1200 N 2000 N 85 Nm 67 Nm 72 Nm Complex loads If more than one force and torque is applied simultaneously, they have to be calculated according to the following formula: L + Ls + M + Ms + Mv 1 L (max) Ls (max) M (max) Ms (max) Mv (max) For models 52M, the load and torque values refer to the center of the tube. For models 52G/52R the load and torque values refer to the center point of the guide. The load and torque values refer to a velocity of: Models 52M/52G 0,2 m/s Models 52R 2 m/s If the velocity exceeds 0.2m/s for the models 52M/52G, the load and torque values have to be multiplied by the coefficients according to the table beside. Correction coefficient, loads speed coefficient 0,2 m/s 1 0,3 m/s 0,75 0,4 m/s 0,5 0,5 m/s 0,4 0,75 m/s 0,27 1 m/s 0,2 These products are designed for industrial applications and are not suitable for sale to the general public. 004

6 *DOC-serie 52 ING.qxd :31 Pagina 8 52 S E R I E S News 2005 END CUSHION DIAGRAM The end cushion regulating screw has to be regulated to obtain a smooth movement at the end of stroke. In those applications which have different values than the ones stated in the diagram (below), external shock-absorbers have to be used. The shock-absorber should be centrally located with respect to the center of the mass. The diagram applies for horizontal operations. Velocity (m/s) Mass (Kg) LOADS ACCORDING TO SUPPORTS DISTANCE The charts below have been made according to a max. deflection of 0.5 mm and 1 mm when a load (N) is applied. The charts reported below give the max distance between two supports in order to stay within the deflection range given. Deflection 0,5 mm Deflection 1,0 mm Max. distance between supports (m) Max. distance between supports (m) 005 These products are designed for industrial applications and are not suitable for sale to the general public.

7 *DOC-serie 52 ING.qxd :31 Pagina 9 News 2005 S E R I E S 52 Mod. 52M2P... + add the stroke K = cushion regulation screw The cylinder has two supply ports I for both endcovers. The operator just needs to choose which one of the two ports to use on each end cover. The remaining ports have to be closed with a tap (two taps are supplied). Series ø W E L1 I B G N L øa H7 øx S1 T Z C1 C U F F1 52M2P25A ,6 200 G1/ ,5 6 4, , M5 7 52M2P32A ,5 240 G1/8 25 5,5 19 9,5 6 5, ,3 7, M5 7 52M2P40A ,6 300 G1/ ,5 7 6, ,2 7, M5 9 Series H V S R P TG Q Q1 52M2P25A M M2P32A M M2P40A M Mod. 52M8P... Where no dimensions are presented, refer to dimensions of cylinder model 52M2P, The cylinder has six ports I located on one endcover. Three ports (x-h-w) to move the carriage in one direction and three (y-z-k) for the opposite direction. The operator just needs to choose which one of the three ports to use for each direction. The remaining ports have to be closed with taps (4 taps are supplied). With supporting feet (mod. B-52 / BA-52), ports h and z have to be closed with a tap. Series ø T1 T2 T3 T4 L2 L3 I 52M8P25A 25 13,5 29,5 13,5 28, G1/8 52M8P32A 32 17,5 34,5 17,5 34,5 9,5 9,5 G1/8 52M8P40A 40 15,5 38,2 20,5 42,5 11,5 11,5 G1/4 These products are designed for industrial applications and are not suitable for sale to the general public. 006

8 *DOC-serie 52 ING.qxd :31 Pagina S E R I E S News 2005 Mod. 52M2C... + add the stroke K = cushion regulation screw The cylinder has two supply ports I for both endcovers. The operator just needs to choose which one of the two ports to use on each end cover. The remaining ports have to be closed with a tap (two taps are supplied). Series ø W L L1 I B G N E øa H7 øx R C F F1 U T V S S1 TG 52M2C25A 25 67,5 9,5 135 G1/ ,6 6 4, M M2C32A 32 77,5 9,5 155 G1/8 25 5, ,6 6 5, M , M2C40A ,5 190 G1/ ,6 7 6, M , Series P Z Q Q1 52M2C25A M4 4, M2C32A M5 7, M2C40A M6 7, Mod. 52M8C... Where no dimensions are presented, refer to dimensions of cylinder model 52M2C The cylinder has six supply ports I located on one endcover. Three ports (x-h-w) to move the carriage in one direction and three (y-z-k) for the opposite direction. The operator just needs to choose which one of the three ports to use for each direction. The remaining ports have to be closed with taps (4 taps are supplied). With supporting feet (mod. B-52 / BA-52), ports h and z have to be closed with a tap. Series ø T1 T2 T3 T4 L2 L3 I 52M8C25A 25 13,5 29,5 13,5 28, G1/8 52M8C32A 32 17,5 34,5 17,5 34,5 9,5 9,5 G1/8 52M8C40A 40 15,5 38,2 20,5 42,5 11,5 11,5 G1/4 007 These products are designed for industrial applications and are not suitable for sale to the general public.

9 *DOC-serie 52 ING.qxd :32 Pagina 11 News 2005 S E R I E S 52 Mod. 52G2P... + add the stroke K = cushion regulation screw The cylinder has two supply ports I for both endcovers. The operator just needs to choose which one of the two ports to use on each end cover. The remaining ports have to be closed with a tap (two taps are supplied). Series ø W E L1 I L T U N C F F1 D B A H G M J 52G2P25A G1/8 9, M5 8 10, ,5 8,6 6,4 4,3-52G2P32A G1/8 9,5 32, M , ,9 8,6 6,4 4,3 M5 52G2P40A G1/4 11,5 38, M , ,8 6,4 4,3 - Series J1 TG Z S R1 P V Q Q1 øy2 Y +0,2 øx H7 Y1 X1 Y3-0,02 C1 +0,05 0 S1 R 52G2P25A , M ,4 4 4,5 5, G2P32A , ,8 M , G2P40A , M , Mod. 52G8P... Where no dimensions are presented, refer to dimensions of cylinder model 52M2C The cylinder has six supply ports I located on one endcover. Three ports (x-h-w) to move the carriage in one direction and three (y-z-k) for the opposite direction. The operator just needs to choose which one of the three ports to use for each direction. The remaining ports have to be closed with taps (4 taps are supplied). With supporting feet (mod. B-52 / BA-52), ports h and z have to be closed with a tap. Series ø T1 T2 T3 T4 L2 L3 I 52G8P25A 25 13,5 29,5 13,5 28, G1/8 52G8P32A 32 17,5 34,5 17,5 34,5 9,5 9,5 G1/8 52G8P40A 40 15,5 38,2 20,5 42,5 11,5 11,5 G1/4 These products are designed for industrial applications and are not suitable for sale to the general public. 008

10 *DOC-serie 52 ING.qxd :32 Pagina S E R I E S News 2005 Mod. 52G2C... + add the stroke K = cushion regulation screw The cylinder has two supply ports I for both endcovers. The operator just needs to choose which one of the two ports to use on each end cover. The remaining ports have to be closed with a tap (two taps are supplied). Series ø W E L1 I L T U N C F F1 D B A H G M J 52G2C25A 25 67, G1/8 9, M5 8 10, ,5 8,6 6,4 4,3-52G2C32A 32 77, G1/8 9,5 32, M , ,9 8,6 6,4 4,3 M5 52G2C40A G1/4 11,5 38, M , ,6 6,4 4,3 - Series J1 TG Z S R1 P V Q Q1 øy2 Y +0,2 øx H7 Y1 X1 Y3-0,02 C1 +0,05 0 S1 R 52G2C25A , M ,4 4 4,5 5, G2C32A , ,8 M , G2C40A , M , Mod. 52G8C... Where no dimensions are presented, refer to dimensions of cylinder model 52G2C. The cylinder has six ports I located on one end cover which supplies both cylinder chambers. Three ports (x-h-w) to move the carriage in one direction and three (y-z-k) for the opposite direction. The operator just needs to choose which one of the three ports to use for each direction. The remaining ports have to be closed with taps (four taps are supplied). With supporting feet (model B-52/BA-52), ports h and z have to be closed with a tap. The guide is applied on the left side of the carriage (can be applied on the right side on request). Series ø T1 T2 T3 T4 L2 L3 I 52G8C25A 25 13,5 29,5 13,5 28, G1/8 52G8C32A 32 17,5 34,5 17,5 34,5 9,5 9,5 G1/8 52G8C40A 40 15,5 38,2 20,5 42,5 11,5 11,5 G1/4 009 These products are designed for industrial applications and are not suitable for sale to the general public.

11 *DOC-serie 52 ING.qxd :32 Pagina 13 News 2005 S E R I E S 52 Mod. 52R2P... ff = these holes are not present in cylinder 25 + add the stroke K = cushion regulation screw The cylinder has two supply ports I for both endcovers. The operator just needs to choose which one of the two ports to use on each end cover. The remaining ports have to be closed with a tap (two taps are supplied). Series ø W E L1 I L T U N C F F1 TG Z S R1 P V Q Q1 øy2 Y +0,2 øx H7 Y1 X1 Y3-0,02 C1 +0,05-0,05 S1 R2 R 52R2P25A G1/8 9, M5 7,5 36 4, M4 68, , R2P32A G1/8 9,5 32, M , ,8 M , , R2P40A G1/4 11,5 38, M , M6 90, , ,5 82 Mod. 52R8P... Where no dimensions are presented, refer to dimensions of cylinder model 52R2P. The cylinder has six ports I located on one end cover which supplies both cylinder chambers. Three ports (x-h-w) to move the carriage in one direction and three (y-z-k) for the opposite direction. The operator just needs to choose which one of the three ports to use for each direction. The remaining ports have to be closed with taps (four taps are supplied). With supporting feet (model B-52/BA-52), ports h and z have to be closed with a tap. The guide is applied on the left side of the carriage (can be applied on the right side on request). Series ø T1 T2 T3 T4 L2 L3 I 52R8P25A 25 13,5 29,5 13,5 28, G1/8 52R8P32A 32 17,5 34,5 17,5 34,5 9,5 9,5 G1/8 52R8P40A 40 15,5 38,2 20,5 42,5 11,5 11,5 G1/4 These products are designed for industrial applications and are not suitable for sale to the general public. 010

12 *DOC-serie 52 ING.qxd :32 Pagina S E R I E S News 2005 Mod. 52R2C... + add the stroke K = cushion regulation screw The cylinder has two supply ports I for both endcovers. The operator just needs to choose which one of the two ports to use on each end cover. The remaining port has to be closed with a tap (two taps are supplied). Series ø W E L1 I L T U N C F F1 TG Z S R1 P V Q Q1 øy2 Y +0,2 øx H7 Y1 X1 Y3-0,02 0 C1 +0,05 S1 R2 R 52R2C25A 25 67, G1/8 9, M5 7,5 36 4, M4 68, , R2C32A 32 77, G1/8 9,5 32, M , ,8 M , , R2C40A ,5190 G1/4 11,5 38, M , M6 90, , ,5 82 Mod. 52R8C... Where no dimensions are presented, refer to dimensions of cylinder model 52R2C. The cylinder has six ports I located on one end cover which supplies both cylinder chambers. Three ports (x-h-w) to move the carriage in one direction and three (y-z-k) for the opposite direction. The operator just needs to choose which one of the three ports to use for each direction. The remaining ports have to be closed with taps (four taps are supplied). With the use of foot bracket (model B-52/BA-52), ports h and z have to be closed with a tap. The guide is applied on the left side of the carriage (can be applied on the right side on request). Series ø T1 T2 T3 T4 L2 L3 I 52R8C25A 25 13,5 29,5 13,5 28, G1/8 52R8C32A 32 17,5 34,5 17,5 34,5 9,5 9,5 G1/8 52R8C40A 40 15,5 38,2 20,5 42,5 11,5 11,5 G1/4 011 These products are designed for industrial applications and are not suitable for sale to the general public.

13 *DOC-serie 52 ING.qxd :32 Pagina 15 News 2005 S E R I E S 52 Foot mount Mod. B The following is supplied: N 2 feet N 4 screws Series ø A1 A2 A2 A3 A4 A5 øa6 A7 A8 A9 (Series 52...P...) (Series 52...C...) B ,5 5,5 5, B , ,5 7,5 8, B , ,5 7,5 8, Foot mount (high) Mod. BA These are to be used in conjunction with intermediate bracket (Mod. BH and BL-52...) The following is supplied: N 2 feet N 4 screws Series ø A1 A2 A2 A3 A4 A5 øa6 A7 A8 A9 (Series 52...P...) (Series 52...C...) BA ,5 12,5 5, BA , ,5 16,5 17, BA , ,5 8,5 17, These products are designed for industrial applications and are not suitable for sale to the general public. 012

14 *DOC-serie 52 ING.qxd :32 Pagina S E R I E S News 2005 Intermediate brackets Mod. BH and BL The following is supplied: screws for fixing the intermediate brackets to the tube profile. The cylinder can safely be mounted by using two intermediate brackets without using the feet bracket. The intermediate brackets BH and BH can be mounted either on sides X or Y or Z of the tube profile. The intermediate support model BH can be mounted on side Z of the tube profile (if the application requires the assembling of an intermediate bracket on sides X-Y, it is necessary to mount the intermediate bracket model BL-52-32). Series ø B1 B2 B3 B4 B5 ØB6 BH , ,5 BH , ,6 BH , , These products are designed for industrial applications and are not suitable for sale to the general public.

15 *DOC-serie 52 ING.qxd :32 Pagina 17 News 2005 S E R I E S 52 Self-compensating adaptor Mod. CF This self-compensating adaptor has been designed to be used with external guides (supplied by the customer). It is used to compensate the difference in alignment between the rodless cylinder and the external guide system. Suitable for cylinders mod. 52M2P/52M2C/52M8P/52M8C. Series ø A X E B Y CF ±8 12 0,8 CF ,9 0,5 ±6 12 0,8 CF ,5 0,5 ±6 12 0,8 These products are designed for industrial applications and are not suitable for sale to the general public. 014

16 *DOC-serie 52 ING.qxd :32 Pagina 2 Camozzi spa Via Eritrea, 20/I Brescia Italy Tel: int Fax: int info@camozzi.com Internet: Camozzi GmbH Pneumatic Porschestrasse Albershausen Germany Tel: int Fax: int info@camozzi.de Camozzi Pneumatics Ltd. The Fluid Power Centre Watling Street Nuneaton Warwickshire CV 11 6BQ Great Britain Tel: int Fax: int info@camozzi.co.uk Camozzi Pneumatique 5, Rue Louis Gattefossé Parc de la Bandonnière Saint Priest France Tel: int Fax: int camozzi@camozzi.fr Camozzi Benelux B.V. De Vijf Boeken 1 G 2911 BL Nieuwerkerk a/d IJssel The Netherlands Tel: int Fax: int info@camozzi.nl Camozzi Pneumatik AB Box 9214 Bronsyxegatan Malmö Sweden Tel: int Fax: int info@camozzi.se Camozzi Aps Metalvej 7a 4000 Roskilde Danmark Tel. int Fax int info@camozzi.dk Camozzi Pneumatic Ltd. Floor 14, Leningradskaya Street, 1-A Himki, Moscow Region Moscow Russian Federation Tel. int Fax int camozzi-moscow@mtu-net.ru Camozzi-Pneumatic 38 Larionova St Simferopol Ukraine Tel: int Fax: int info@camozzi.com.ua Camozzi Pneumatic Karbusheva St. 2 Off Gomel Byelorussia Tel: int Fax: int camozzi@mail.gomel.by Camozzi Pneumatics Inc Redbud Blvd., TX P.O. Box 2386, TX McKinney - Texas U.S.A. Tel: int Fax: int office@camozzi-usa.com Camozzi Neumatica S.A. de C.V. Av. Santa Ana 18 Parque Industrial Lerma Lerma Mexico Tel: int Fax: int camozzi@camozzi.com.mx Camozzi do Brasil Ltda. Rua Estácio de Sá, 530 Jd. Sta Genebra, Campinas CEP São Paolo Brazil Tel.: int Fax: int camozzi@camozzi.com.br Camozzi Neumatica S.A. Prof.Dr. Pedro Chutro Buenos Aires Argentina Tel.: int Fax.: int info@camozzi.com.ar Camozzi Venezuela S.A. Calle 146 con Av. 62 N P.O.Box 529 Zona Industrial Maracaibo Edo. Zulia Venezuela Tel: int Fax: int venezuela@camozzi.com Camozzi Colombia, Ltda Carrera 34 # 22 D-02 Santa Fé De Bogotà Colombia Tel: int Fax: int camozzi@aolpremium.com Camozzi Iran Co. Ltd. Motahari Ave. No. 243 Teheran Iran Tel: int & int Fax: int adm-camir@safineh.net Shanghai Camozzi Pneumatic Control Components Co, Ltd. 415, Ren De Road Shanghai China Tel: int Fax: int ynxie@public1.sta.net.cn Camozzi India Private Limited C-130 Phase II Ext., Hosiery Complex Noida (uttar Pradesh) India Tel: Fax: info@camozzi-india.com Camozzi Malaysia SDN BHD 30, Jalan Pemberita, U1/49 Seksyen U1 Temasya Industrial Park Shah Alam Malaysia Tel: Fax: camozzijb@myjaring.net GB048/04-05 MIX COMUNICAZIONE - MI w w w. c a m o z z i. c o m