M/146000, M/146100, M/146200

Transcription

1 LINTR PLUS rodless cylinders Magnetic piston and non-magnetic piston Double acting Ø 3 to 50 mm New lightweight design extrusion with universal mounting grooves Proved and patented sealing system Dust protection as standard Up to 10% higher loading values against internal guiding series M/46000 Interchangeability with series M/46000 Technical data Medium: Compressed air, filtered, lubricated or non-lubricated Operation: M/146000, M/146100, M/14600 Double acting, with adjustable cushioning M/146000/M, M/146100/M, M/14600/M Double acting with adjustable cushioning and magnetic piston Models: M/ with internal guide M/ with external adjustable guide M/14600 with precision roller guide Operating pressure: 1 to bar Operating temperature: -30 C to +0 C max. (consult our Technical Service for use below + C) Cylinder diameter: 3, 40, 50 mm Max strokes: Ø 3 to 40 mm 500 mm Ø 50 mm 000 mm Materials: nd covers, closer, carriage and Top cover: aluminium diecast Yoke, guiding bridge and profile barrel: anodised aluminium Seal strip, wiper and piston seal: polyurethane Cover strip: polyamide Other seals: nitrile rubber Mounting screws: Shim ring: stainless steel () Ordering example See page 4 Mountings and switches See page 3 & 4 lternative cylinder See page LINTR rodless cylinders ø16 to 0 mm see page Heavy duty cylinders see page TX cylinders see page TX014_101 Non-magnetic piston magnetic piston /07 Our policy is one of continued research and development. We therefore reserve the right to amend, N/UK

2 lternative variants Symbol Type (non-magnetic piston) Symbol Type (magnetic piston) Description Page M/ M/146000/M With internal guide 6 M/ M/146100/M With external adjustable guide 7 M/14600 M/14600/M With precision roller guide M/14600/P M/14600/PM With added caged ball linear motion guide on request 9 M/146000/IC M/146000/MC With alternative ports 10 M/146100/IC M/146100/MC M/14600/IC M/14600/MC M/146100/ID M/146100/MD Clinder with double carriages 7 + M/14600/ID M/14600/MD M/146000/L1 M/146000/L3 ctive holding brake M/14600/L1 M/14600/L3 pplying pressure activates the brake The brake lining is pushed against a stainless steel strip. To release, depressurize. M/146000/L M/146000/L4 Passive holding brake; M/14600/L M/14600/L4 pplying pressure releases the brake. When the pressure is released the brake lining is pushed against the stainless steel strip by a spring loaded plate. Options selector M/146 / / Guiding system Substitute Internal 0 xternal 1 Roller Cylinder Ø (mm) Substitute 3, 40, 50 Note: Disregard option positions not used. For combinations of cylinder variants consult our Technical Service. This options selector explains only the cylinder variants. dditional variants/options are not possible. Strokes (mm) On request Variants (non-magnetic piston) Substitute lternative ports IC ctive brake L1 Passive brake L With added caged ball linear motion guide P Double carriages *1) ID M/146***/ID/****/**** Distance between carriage centres (mm) Variants (magnetic piston) Substitute lternative ports MC ctive brake L3 Passive brake L4 With added caged ball linear motion guide PM Double carriages *1) MD M/146***/MD/****/**** Distance between carriage centres (mm) *1) For M/ & M/14600 only Warning These products are intended for use in industrial compressed air systems only. Do not use these products where pressures and temperatures can exceed those listed under Technical Data. Before using these products with fluids other than those specified, for non-industrial applications, life-support systems, or other applications not within published specifications, consult NORGRN. Through misuse, age, or malfunction, components used in fluid power systems can fail in various modes. The system designer is warned to consider the failure modes of all component parts used in fluid power systems and to provide adequate safeguards to prevent personal injury or damage to equipment in the event of such failure. System designers must provide a warning to end users in the system instructional manual if protection against a failure mode cannot be adequately provided. System designers and end users are cautioned to review specific warnings found in instruction sheets packed and shipped with these products. N/UK Our policy is one of continued research and development. We therefore reserve the right to amend, /07

3 Mountings Type C Type S Type UV Type UW Type V 1 Ø mm Page 1 Page 13 Page 13 Page 13 Page 1 3 QM/4603/1 QM/14603/37 QM/4603/34 QM/4613/36 QM/4603/3 40 QM/46040/1 QM/14603/37 QM/46040/34 QM/46140/36 QM/46040/3 50 QM/46050/1 QM/146050/37 QM/46050/34 QM/46150/36 QM/46050/3 Type W ssembly kit for caged ball djustable stop Groove key for Groove key for linear motion guide profile barrel guiding bridge Ø mm Page 13 Page 9 Page 14 Page 14 Page 14 3 QM/14613/35 QM/1463/P/70 QM/4613/75 M/P74065 M/P QM/146140/35 QM/14640/P/70 QM/46140/75 M/P74065 M/P QM/146150/35 QM/14650/P/70 QM/46150/75 M/P74065 M/P /07 Our policy is one of continued research and development. We therefore reserve the right to amend, N/UK

4 Switches With cable With connector (Mx1) Cable Cable with Type Voltage Current Temperature LD Features Connector Cable connector Reed Solid state V C V DC max. C length type straight Datasheet M/50/LSU/*V 10 to to m -0 to +0, 5, 10 m PVC x 0,5 N/UK M/50/LSU/5U 10 to to m -0 to +0 5 m PUR x 0,5 N/UK TM/50/RU/S 10 to to m -0 to +150 m Silicon x 0,5 N/UK M/50/RC/5V 10 to to m -0 to +0 Changeover 5 m PVC 3 x 0,5 N/UK M/50/LSU/CP 10 to to m -0 to +0 Plug Mx1 5 m PVC 3 x 0,5 M/P73001/5 N/UK M/50/P/*V 10 to m -0 to +0 PNP, 5, 10 m PVC 3 x 0,5 N/UK M/50/P/CP 10 to m -0 to +0 PNP, plug Mx1 5 m PVC 3 x 0,5 M/P73001/5 N/UK M/50/P/CC 10 to m -0 to +0 PNP, plug M1x1 5 m PVC 3 x 0,5 M/P34614/5 N/UK M/50/N/*V 10 to m -0 to +0 NPN, 5, 10 m PVC 3 x 0,5 N/UK M/50/N/CP 10 to m -0 to +0 NPN, plug Mx1 5 m PVC 3 x 0,5 M/P73001/5 N/UK * Please insert cable length Further information (Technical data, cable material, dimensions) see data sheet Theoretical forces, air consumption, cushioning length, holding forces Cylinder Theoretical forces (N) ir consumption (l/cm) Cushioning length Holding forces (N) of brake (on dry braking surface) Ø mm at 6 bar of stroke at 6 bar (mm) active (L1 + L3) at 6 bar passive (L + L4) 3 4 0, , , Cushioning Performance The dynamic energy of a LINTR cylinder is caused by direct or partial external loads which must be absorbed by pneumatic cushioning. The cushioning ability depends to a large extent on the pneumatic circuit (e. g. counter pressure, pre-exhaust). The values given in the diagram were tested with an operation pressure of 6 bar using a 5/ control valve. When installed horizontally, depending upon the speed, dynamic energy can be absorbed by the cylinder. Whenever the values given in the diagram are exceeded, the transported mass must be cushioned by additional shock absorbers. These have to be located at the center of gravity of the mass. Cylinder deflection F (N) Deflection due to external forces f1= 1 mm (kg) ,4 0, 1, 1,6,0 ø 50 ø 40 ø 3 V (m / s) 1000 Deflection due to cylinder weight 500 f (mm) 100 ø50 ø40 1 0,4 0,9 ø3 0, (mm) Support length Support length (mm) xample: Cylinder Ø 3 mm, stroke length 3500 mm, external load 00 N and a deflection about 1 mm Maximum distance between supports = 130 mm (see diagrams). Therefore an additional support is required. xample: Cylinder Ø 40 mm, external force 10 N, distance between supports 3000 mm Required: total deflection 1. Deflection due to external force (f1) see Diagramm 1 (1mm/100 N) 10 N 1, mm. Deflection due to cylinder weight diagram + 0,9 mm Total deflection:,7 mm Max. permitted deflection (f1 + f) < 1 mm 1000 mm Hub deflection of more than 3 mm is not permitted. N/UK Our policy is one of continued research and development. We therefore reserve the right to amend, /07

5 M/146000, M/146100, M/14600 M/14600/P Internal guide xternal adjustable guide Precision roller guide dded caged linear ball M/ M/ M/14600 motion nguide M/14600/P Fy Fz Mx My Mz Fy, Fz Mx My, Mz Fy Fz Mx My, Mz Fy, Fz Mx My,Mz Ø mm (N) (N) (Nm) (Nm) (Nm) (N) (Nm) (Nm) (N) (N) (Nm) (Nm) , Loading values applicable to a speed of 0, m/s. Maximum working life is normally reached below a speed of 1 m/s. * The forces and moments refers to the centre of the guide. They must not be exceeded in dynamic applications. M/146100/ID, M/146100/MD X xternal adjustable guide, M/146100/ID and M/146100/MD Fy, Fz Mx My, Mz (Nm) Ø mm (N) (Nm) x min.= x=100 mm x=150 mm x=00 mm x=50 mm x=300 mm x=350 mm x=400 mm x=450 mm x=500 mm Precision roller guide M/14600/ID and M/14600/MD Fy, Fz Mx My, Mz (Nm) Ø mm (N) (Nm) x min.= x=100 mm x=150 mm x=00 mm x=50 mm x=300 mm x=350 mm x=400 mm x=450 mm x=500 mm Loading values applicable to a speed of 0, m/s. Maximum working life is normally reached below a speed of 1 m/s. * The forces and moments refers to the centre of the guide. They must not be exceeded in dynamic applications. Loading values for LINTR cylinders with double carriages The values given in the table below show the single forces in the directions Fy and Fz and the maximum moments Mx, My and Mz. ll values are applicable only for speeds of max. 0, m/s. requirement for using these values is a constant movement (no jerking) of the mass over the whole stroke length of the cylinder. The reference point from which the moments for all cylinders should be calculated is the centre line of the pistons. For speeds up to m/s please use our calculation programme LINTR PNUCLC. It is available upon request. When a LINTR cylinder has to take several loads and moments, an additional calculation is necessary using this formula: Mx My Mz Fy Fz <_ 1 Mx max My max Mz max Fy max Fz max /07 Our policy is one of continued research and development. We therefore reserve the right to amend, N/UK

6 Basic dimensions M/ cylinder with internal guide - 1 M B D K T N W Z C 5 J Y 3 5,3 C O P 5 6 C 4 # 1 S 6,5 R O1 x + # G F G # Stroke 1 Cushion screw Main port 3 Main port 4 lternative port with plug inserted 5 M/50 switches and groove key can be mounted flush with the profile 6 For groove key only Type Ø C G B C C D 1 F G J Ø K D7 M/14603/ ,5 10,5 1 G1/ , M/146040/ ,5 90 5,5 11,5 1 G1/ M/146050/ , G3/ ,5 9 Type Ø M N O O 1 P R S T W Y Z Weight Weight at 0 mm per 100 mm M/14603/ M M6-17*1) 0 0 1,40 kg 0,30 kg M/146040/ M ,5 5 M-0*1) 5 5,50 kg 0,4 kg M/146050/ M 0 4 5, M-0*1) ,5 4,40 kg 0,6 kg *1) deep N/UK Our policy is one of continued research and development. We therefore reserve the right to amend, /07

7 M/ cylinder with external adjustable guide 1 L B K J Y D C R F x + # # B # Stroke 7 Supplied complete with four groove keys 7 Center bore Ø 6 H7, 4 deep Missing cylinder dimensions see page 6 Type Ø B 1 B D C F J Ø K L R Y Weight Weight ±0,05 at 0 mm per 100 mm M/14613/ ,5 5 5, ,5 1,50 kg 0,30 kg M/146140/ , , ,5,60 kg 0,4 kg M/146150/ , ,5 6, ,5 4,50 kg 0,6 kg Groove key for carriage (pos. 7) Type Ø B C D Weight (kg) M/P M ,01 M/P ,5 M ,5 0,0 M/P ,5 M 3 7,5 13,5 0,03 B D C M/146100/ID,.../MD cylinder with external adjustable guide and double carriages X 1 x + X + # Missing cylinder dimensions see page 6 # Stroke Type Ø 1 X min. X max. Weight at 0 mm Weight per 100 mm M/14613/.D ,00 kg 0,30 kg M/146140/.D ,0 kg 0,4 kg M/146150/.D ,40 kg 0,6 kg /07 Our policy is one of continued research and development. We therefore reserve the right to amend, N/UK

8 M/14600 cylinder with precision roller guide CC CH CG CF C CD # x + # 9 CB C # Stroke 9 Center bore Ø 6 H7, 4 deep For lubrication Missing cylinder dimensions see page 6 Type Ø C CB CC CD C CF CG CH Weight Weight ±0,05 at 0 mm per 100 mm M/1463/ M-16*1) ,0 kg 0,40 kg M/14640/ M-16*1) 4 57, ,50 kg 0,45 kg M/14650/ M10-0*1) , ,0 kg 0,90 kg *1) deep M/14600/ID and.../md cylinder with precision roller guide and double carriages X x + X + # Missing cylinder dimensions see page 6 # Stroke Type Ø X min. X max. Weight Weight at 0 mm per 100 mm M/1463/.D/ ,0 kg 0,40 kg M/14640/.D/ ,00 kg 0,45 kg M/14650/.D/ ,10 kg 0,90 kg N/UK Our policy is one of continued research and development. We therefore reserve the right to amend, /07

9 M/14600/P and M/14600/PM cylinder with added caged ball linear motion guide F F FB FC FD FH FJ FK FL FF FG FM FN 10 x + # # Missing cylinder dimensions see page 6 Type Ø F FB FC FD F FF FG FH FJ FK FL FM FN Weight Weight ±0,05 at 0 mm per 100 mm M/1463/P/ M ,5 79, ,90 kg 0,50 kg M/14640/P/ M ,5 5, ,5 5,5 4,70 kg 0,65 kg M/14650/P/ M , ,5,50 kg 1,10 kg Note: stroke max ø 3 & 40 = 1500, ø 50 = 600 QM/14600/P/70 ssembly kit for caged ball linear motion guide ø G ø GF GG G GB GC # Stroke 11 Standard cylinder M/ ssembly kit for caged ball linear motion guide 10 Center bore Ø 6 H7, 4 deep Recommended supplier/series for caged ball linear motion guide Cylinder Ø 3 and 40 IKO/LWFF33 NSK/LW17LZ THK/SHW17CM Cylinder Ø 50 IKO/LWFF4 NSK/LW7LZ THK/SHW7CN Missing dimensions on the top Type Ø G GB GC Ø G Ø GF GG Weight kg QM/1463/P/ ,5 4,5 53 0,470 QM/14640/P/ ,5 4,5 53 0,470 QM/14650/P/ ,5 6, ,315 /07 Our policy is one of continued research and development. We therefore reserve the right to amend, N/UK

10 M/146000/IC,.../MC; M/146100/IC,.../MC; M/14600/IC,.../MC cylinder with alternative ports W Missing cylinder dimensions and weights see the corresponding series on page 6, 7 or. Type Ø W M/146.3/ ,5 M/146.40/ ,5 M/146.50/ lternative ports N/UK Our policy is one of continued research and development. We therefore reserve the right to amend, /07

11 M/146000/L1, M/146000/L3 cylinder with active brake P Y M U N O K R ø U G F G 1/ Z CO L F G Missing cylinder dimensions see page 6 Type Ø F G K L M N O P R U Y Z CO F G Ø U Weight Weight at 0 mm per 100 mm M/14603/L ,5 17,5 3, ,50 kg 0,35 kg M/146040/L ,5 103,5 13, , ,0 kg 0,50 kg M/146050/L ,5 14,5 14, ,5 14 1, ,90 kg 0,75 kg M/146000/L, M/146000/L4 cylinder with passive brake P CO O Y K M R N U G 1/ Z G F ø U L F G Missing cylinder dimensions see page 6 Type Ø F G K L M N O P R U Y Z CO F G Ø U Weight Weight at 0 mm per 100 mm M/14603/L ,5 9,5 3, ,60 kg 0,35 kg M/146040/L ,5 115,5 5, , ,70 kg 0,50 kg M/146050/L ,5 14,5 3, , , ,0 kg 0,75 kg /07 Our policy is one of continued research and development. We therefore reserve the right to amend, N/UK

12 M/14600/L1, M/14600/L3 cylinder with precision roller guide and active brake P M Y N O K R ø U G G 1/ Z CO L F F G Missing cylinder dimensions see page Type Ø F G K L M N O P R U Y Z CO F G Ø U Weight Weight at 0 mm per 100 mm M/1463/L ,5 17,5 3, ,90 kg 0,35 kg M/14640/L ,5 10,5 13, , ,0 kg 0,50 kg M/14650/L ,5 16,5 14, ,5 14 1, ,70 kg 0,75 kg M/14600/L, M/14600/L4 cylinder with precision roller guide and passive brake P CO Y K O M R N G 1/ Z G F ø U L F G Missing cylinder dimensions see page Type Ø F G K L M N O P R U Y Z CO F G Ø U Weight Weight at 0 mm per 100 mm M/1463/L ,5 9,5 3, ,00 kg 0,35 kg M/14640/L ,5 10,5 5, , ,70 kg 0,50 kg M/14650/L ,5 144,5 3, , , ,00 kg 0,75 kg N/UK Our policy is one of continued research and development. We therefore reserve the right to amend, /07

13 Mountings Foot mounting C Centre support V 1 D M K 1 TOP R ø U B C H J F G ø U 1 Style Ø B C D R Ø U kg QM/4603/ ,5 30,5 (33) ,1 QM/46040/ ,5 37,5 (40,5) , QM/46050/ (49) ,3 Style Ø F G H J K M Ø U1 kg QM/4603/3 3 30, ,5 13,5 9 0,07 QM/46040/ , ,5 1,5 9 0, QM/46050/ ,5 1,5 11 0, ttention: Foot mounts can be attached to give different distances. When used together with a centre support mounting the word TOP should be visible on the top face of the mount. Carriage plate mounting UV P M 1 K 1 N G F ø U 1 L F G Ø Style Ø F G K1 L M1 N P F G U1 kg QM/4603/ , ,40 QM/46040/ , , ,0 QM/46050/ ,0 Swinging bridge S Fx Q V S R + - X U W T 5 mm I Fx Style Ø Q R S T U V W X I (N) kg QM/14603/ DIN74-Bm M6 5,5, ,30 QM/146040/ DIN74-Bm M6 5,5 10, ,30 QM/146050/ DIN74-Bm 40 0 M 6, ,50 /07 Our policy is one of continued research and development. We therefore reserve the right to amend, N/UK

14 Secondary carriage W Side mounting plate UW BG F G L M BJ BK HB HC BM BL 1 1 Secondary carriage W Side mounting plate UW Style (W) Style (UW) Ø BG BJ BK BL BM F G HB HC L M W UW QM/14613/35 QM/4603/36 3 M 5 x 1*1) ,50 kg 0,50 kg QM/146140/35 QM/46040/ ,5 M 6 x 1*1) 9 5, ,65 kg 1,0 kg QM/146150/35 QM/46050/ M 6 x 15*1) 117,5 71, ,10 kg 1,5 kg *1) deep M/P74065 Groove key Weight: 0,01 kg M 5 1 djustable stop For M/146100, /..,../M, M/14600/...,.../M + SH SF SH 3 1 SG S S SI Missing cylinder dimensions see the corresponding series on pages 7 or Style Ø S S SF SG SH SI Weight QM/14613/ M14x1, ,5 0,17 kg QM/146140/ M0x1, , kg 1 ssembly kit 3 Please order shock absorber separately, see C program Reaction forces (Q max) ø 3 = 1500 N, ø 40 = 150 N N/UK Our policy is one of continued research and development. We therefore reserve the right to amend, /07

15 Spares & 9 For M/146000,.../M, M/14600,.../M Ø Type Spares kit Comprising Seal strip Cover strip Item Description Quantity Item Item 3 3 M/14603,.../M, M/1463,.../M QM/14603//* 1 Clamping lever M/P 40344/* M/P73936/* 40 M/146040,.../M, M/14640,.../M QM/146040//* + 3 Seal-/cover strip 1 M/P 4063/* M/P73945/* O-ring 50 M/146050,.../M, M/14650,.../M QM/146050//* M/P 4066/* M/P73946/* 6 Seal Seal 10 Wiper 1 Grease 1 * Insert stroke length Note: Please quote the cylinder type number when ordering spare parts For M/146100,.../M Ø Type Spares kit Comprising Seal strip Cover strip Item Description Quantity Item Item 3 3 M/14613,.../M QM/14613/*/ 1 Clamping lever M/P 40344/* M/P73936/* 40 M/146140,.../M QM/146140/*/ + 3 Seal-/cover strip 1 M/P 4063/* M/P73945/* O-ring 50 M/146150,.../M QM/146150/*/ M/P 4066/* M/P73946/* 6 Seal 7 Guide bar 4 Seal 9 Felt 10 Wiper 1 Grease 1 * Insert stroke length Note: Please quote the cylinder type number when ordering spare parts /07 Our policy is one of continued research and development. We therefore reserve the right to amend, N/UK