Product Data Sheet. Positive Displacement Flow Meter B1750 DESCRIPTION
|
|
- Barbara Ray
- 5 years ago
- Views:
Transcription
1 ESRIPTION Positive isplacement Flow Meter 175 The lancett Model 175 positive displacement flow meter provides high measurement accuracy, trouble-free operation and long service life for fluids over a wide viscosity range. pplications include lubricants, fuels, chemicals, solvents, oils, and greases. The 175 meter is bi-directional (using appropriate electronics) and has an extremely large turndown ratio, up to 4:1 in some models, with full accuracy at extremely low flow rates. FETURES ccuracy of ±.5 percent of reading and repeatability of ±.1 percent. No need for additional straight run piping. esigned for fluids with a wide range of viscosities, as well as low flow rates. vailable in high strength aluminum or stainless steel housing. OPERTING PRINIPLE Fluid entering the meter drives two gears. non-intrusive sensor detects the movement of the gears and produces a sine wave pulse for each gear tooth that passes the path of the sensor face. The resulting pulse frequency is proportional to the actual flow rate, and it provides a highly accurate representation of the fluid flow. The meter is relatively insensitive to changes in viscosity and there is no need for straight run piping. IN OUT SPEIFITIONS ccuracy Repeatability ±.1% Pressure Rating Operating Temperature onnections Material of onstruction O-ring Housing ±.5% over the published flow range with fluids >1 cp; over a 1:1 turndown (from maximum flow) with fluids <3 cp 5 psi (345 bar) maximum F ( ) aluminum 2 4 F ( ) stainless steel Female NPT: 1/4 in., 3/4 in. or 1-1/4 in. (depending on meter size) Stainless steel (gears and bearings) Teflon, Viton (optional) 661-T6 aluminum or 33 stainless steel K-FTOR The K-factor represents the number of output pulses transmitted per unit volume of liquid passing through the positive displacement meter. Each meter has a unique K-factor that is determined during factory calibration. The K-factor is very constant and linear over the published flow range when liquid viscosity is greater than 1 entipoises. When liquid viscosity is less than 1 entipoises, positive displacement meters can experience fluid slip in the measuring chamber due to migration of liquid around the internal moving parts. s a result, the linear (constant K-factor portion) measuring range of the flow meter is reduced. t viscosities less than 3 entipoises, positive displacement meters maintain published linearity over a 1:1 turndown range from the maximum published flow rate. PM-S-113-EN-2 () Product ata Sheet
2 Positive isplacement Flow Meter, 175 PRESSURE ROP VS FLOW RTE Model /175-S12 15 cst 8 cst 63 cst 3 cst 15 cst 5 cst GPM Model 175-3/175-S3 3 cst 2 cst 1 cst 5 cst Model 175-8/175-S8 3 cst 1 cst 5 cst 3 cst GPM Model 175-2/175-S2 3 cst 2 cst 15 cst 1 cst 8 cst 5 cst 4 cst 3 cst 2 cst 1 cst cst GPM Model 175-6/175-S6 3 cst 2 cst 1 cst 5 cst Model 175-9/175-S9 3 cst 1 cst 5 cst 3 cst GPM cst 3 cst 15 cst 4 cst GPM cst cst cst cst GPM Page 2 PM-S-113-EN-2
3 imensions IMENSIONS Model /175-S12 Sensor Port /4 NPT Ports E F 1/4-2 N (2 PL) G E F G Model 175-2/175-S2 1/4 NPT Ports M6 x.4 (1) eep Thread (2 PL) (diameter) Model 175-3/175-S3 1/2 NPT Ports M6 x.4 (1) eep Thread (2 PL) (diameter) Model 175-6/175-S6 3/4 NPT Ports M8 x.63 (16) eep Thread (2 PL) (diameter) PM-S-113-EN-2 Page 3
4 Positive isplacement Flow Meter, 175 Model 175-8/175-S8 1/2-13 UN (1 PL) E (diameter) olt Patterns: SE 1-1/4 in. 6 psi 4-olt Flange F E F Model 175-9/175-S9 1/2-13 UN (1 PL) E (diameter) olt Patterns: SE 1-1/4 in. 6 psi 4-olt Flange F E F ORERING INFORMTION luminum Housing 185 F Maximum Fluid Temperature Part Number1 Seal Material End onnection GPM Flow Ranges3 LPM K factor2 Pulse/Gallon 1/4 in. Female NPT , /4 in. Female NPT , /2 in. Female NPT Teflon Standard /4 in. Female NPT ⁴ 1-1/4 in. Female NPT * 175-9⁴ 1-1/4 in. Female NPT * V 1/4 in. Female NPT , V 1/4 in. Female NPT , V 1/2 in. Female NPT Viton V 3/4 in. Female NPT V⁴ 1-1/4 in. Female NPT * V⁴ 1-1/4 in. Female NPT * 1 oes NOT include pickup. 2 ll K factors are approximate. 3 ccuracy: ±.5 percent over the published flow range with fluids greater than 1 entipoises; over a 1:1 turndown (from maximum flow) with fluids less than 3 entipoises. ⁴ 9-degree flange fittings required for installation, see the lancett price list. * onfigured for Quad-4 sensor output (1718). Page 4 PM-S-113-EN-2
5 Ordering Information 33 Stainless Steel Housing 4 F Maximum Fluid Temperature Part Number 1 Seal Material End onnection 175-S12 GPM Flow Ranges 3 LPM K factor 2 Pulse/Gallon 1/4 in. Female NPT , 175-S2 1/4 in. Female NPT ,9 175-S3 1/2 in. Female NPT Teflon Standard 175-S6 3/4 in. Female NPT S8⁴ 1-1/4 in. Female NPT * 175-S9⁴ 1-1/4 in. Female NPT * 175-S12-V 1/4 in. Female NPT , 175-S2-V 1/4 in. Female NPT ,9 175-S3-V 1/2 in. Female NPT Viton 175-S6-V 3/4 in. Female NPT S8-V⁴ 1-1/4 in. Female NPT * 175-S9-V⁴ 1-1/4 in. Female NPT * 1 oes NOT include pickup. 2 ll K factors are approximate. 3 ccuracy: ±.5 percent over the published flow range with fluids greater than 1 entipoises; over a 1:1 turndown (from maximum flow) with fluids less than 3 entipoises. 4 9-degree flange fittings required for installation, see the lacett Price List. * onfigured for Quad-4 sensor output (1718). Optional Magnetic Pickups/Sensors Part Number escription For Use With 1719 Magnetic pickup, 6 series , 175-S Pickup, hall effect; 12 Series , 175-S Magnetic pickup. 2 and 3 series , 175-S2 175-S Magnetic pickup with preamp, 2 and 3 series , 175-S2 175-S Quad-4 sensor, , 175-S8 175-S Magnetic pickup with preamp, 6 series , 175-S able for quad-4 sensor; 1 ft , 175-S8 175-S onnector for quad-4 cable , 175-S8 175-S m nalog output sensor , 175-S S6 PM-S-113-EN-2 Page 5
6 Positive isplacement Flow Meter, 175 INTENTIONL LNK PGE Page 6 PM-S-113-EN-2
7 Product ata Sheet INTENTIONL LNK PGE PM-S-113-EN-2 Page 7
8 Positive isplacement Flow Meter, 175 ontrol. Manage. Optimize. lancett is a registered trademark of adger Meter, Inc. Other trademarks appearing in this document are the property of their respective entities. ue to continuous research, product improvements and enhancements, adger Meter reserves the right to change product or system specifications without notice, except to the extent an outstanding contractual obligation exists. 214 adger Meter, Inc. ll rights reserved. The mericas adger Meter 4545 West rown eer Rd PO ox Milwaukee, WI México adger Meter de las mericas, S.. de.v. Pedro Luis Ogazón N 32 Esq. ngelina N 24 olonia Guadalupe Inn P 15 México, F México Europe, Middle East and frica adger Meter Europa GmbH Nurtinger Str Neuffen Germany Europe, Middle East ranch Office adger Meter Europe PO ox ubai Silicon Oasis, Head Quarter uilding, Wing, Office #29 ubai / UE zech Republic adger Meter zech Republic s.r.o. Maříkova 282/ rno, zech Republic Slovakia adger Meter Slovakia s.r.o. Racianska 19/ ratislava, Slovakia sia Pacific adger Meter 8 Marine Parade Rd 21-6 Parkway Parade Singapore hina adger Meter Hangzhong Road Minhang istrict Shanghai hina Legacy ocument Number: 2-PM-UM-134-EN
Product Data Sheet. Flow Monitor. B2800 Series DESCRIPTION OPERATION FEATURES
Flow Monitor 2800 Series SRIPTION The 2800 flow monitor is designed to be comprehensive, user-friendly, flexible and cost efficient. This microprocessor-based display comes pre-calibrated when purchased
More informationProduct Data Sheet. Exact Dual Rotor. Turbine Flow Meters DESCRIPTION CALIBRATIONS APPLICATIONS
Exact Dual Rotor Turbine Flow Meters DESRIPTION The ox Exact Dual Rotor Turbine Flow Meter is the pinnacle of turbine meter technology that delivers results not attainable with single rotor designs. The
More informationProduct Data Sheet. Turbine Flow Meters. Precision Series DESCRIPTION CALIBRATIONS APPLICATIONS
Turbine Flow Meters Precision Series DESRIPTION ox Precision Turbine Flow Meters have unprecedented mechanical linearity, resulting in minimizing, or negating, temperature induced viscosity influence.
More informationProduct Data Sheet. Industrial Oval Gear. Inline and Flanged Meters, 1/2", 3/4", 1", 1" HF, 1-1/2", 2", 3" DESCRIPTION OPERATING PRINCIPLE
Industrial Oval Gear Inline and Flanged Meters, 1/2", 3/4", 1", 1" HF, 1-1/2", 2", 3" DESCRIPTION The Badger Meter Industrial Oval Gear Meter, Model IOG is a modular flow meter design, economical yet highly
More informationProduct Data Sheet. Electronic Valve Actuator. SEVA (Smart Electronic Valve Actuator) DESCRIPTION FEATURES APPROVALS / RATINGS OPERATION
Electronic Valve ctuator SEV (Smart Electronic Valve ctuator) DESCRIPTION The SEV is our next generation Smart Electric Valve ctuator that provides our customers with an electric actuator with best-in-class
More informationProduct Data Sheet. Turbine Flow Meter. B16D Series FloClean Sanitary DESCRIPTION INSTALLATION REPAIR KITS
DESCRIPTION Turbine Flow Meter The FloClean Sanitary turbine flow meter was developed for use in the food, beverage and pharmaceutical industries. The 36L stainless steel construction provides a durable
More informationParts List. Recordall Turbo Series Meters
Recordall Turbo Series Meters Models 160 (1-1/ in.), 00 ( in.), 450 (3 in.), 1000 (4 in.), 000 (6 in.), 3500 (8 in.), 5500 (10 in.), 600 (1 in.) Models without Integral Strainers, Sizes 1-1/ 1 in. Models
More informationProduct Data Sheet. Turbine Flow Meter. QuikSert DESCRIPTION INSTALLATION FEATURES REPAIR KITS
DESCRIPTION Turbine Flow Meter QuikSert The QuikSert in-line turbine flow meter was developed for liquid applications where accuracy and dependability are needed. QuikSert s stainless steel body incorporates
More informationProduct Data Sheet. Coriolis Flow Meter RCT1000 DESCRIPTION APPLICATIONS MAINTENANCE OPERATION FLUID DIAGNOSTICS ADVANTAGES
oriolis Flow Meter ESRIPTION RT1000 The RT1000 oriolis mass flow meter identifies flow rate by directly measuring mass flow and density of fluids over a wide range of process temperatures with a high degree
More informationProduct Data Sheet. Recordall Disc Meters. Lead-Free Bronze Alloy, Sizes 5/8", 5/8" x 3/4", 3/4" & 1" NSF/ANSI Standards 61 and 372 Certified
Recordall Disc Meters LeadFree Bronze Alloy, Sizes /8", /8" x 3/4", 3/4" & " NSF/ANSI Standards 6 and 372 Certified LP /8", /8" 3/4" 2 /8", /8" 3/4" 3 3/4" " 7 " DESCRIPTION The Recordall Disc Series meters
More informationProduct Data Sheet DESCRIPTION
Turbo Series Meters Models 16 (11/2"), 2 (2"), 4 (3"), (4"), 2 (6"), 3 (8"), ("), & 62 (12"); NSF/ANSI Standards 61 and 372 Certified DESCRIPTION Turbo Series meters meet or exceed the most recent revision
More informationProduct Data Sheet. Flow Sensors. Insert Style Flow Sensors SDI Series DESCRIPTION HOT TAP SENSORS (OPTIONAL) APPLICATIONS FUNCTIONALITY
DESCRIPTION Flow Sensors Insert Style Flow Sensors SDI Series The Data Industrial SDI Series insert flow sensors from Badger Meter offer accurate liquid flow measurement in closed pipe systems in an easy
More informationProduct Data Sheet DESCRIPTION
Turbo Series Meters Models 16 (11/), 2 (), 4 (3 in.), (4 in.), 2 (6 in.), 3 (8 in.), ( in.) and 62 (1) NSF/ANSI Standards 61 and 372 Certified DESCRIPTION Turbo Series meters meet or exceed the most recent
More informationProduct Data Sheet. Recordall Disc Meters. Lead-Free Bronze Alloy, Sizes 5/8, 5/8 x 3/4, 3/4 & 1 inch NSF/ANSI Standards 61 and 372 Certified
Recordall Disc Meters LeadFree Bronze Alloy, Sizes /8, /8 x 3/4, 3/4 & inch NSF/ANSI Standards 6 and 372 Certified 2 /8 in., /8 3/4 in. 3 3/4 in. in. 7 in. DESCRIPTION The Recordall Disc Series meters
More informationTurbine Flow Meter. Model User Manual. TRB-UM EN-03 (December 2015)
Turbine Flow Meter Model 1200 TRB-UM-00290-EN-03 () User Manual Turbine Flow Meter, Model 1200 CONTENTS Scope of This Manual 3 Unpacking and Inspection 3 Safety 3 Terminology and Symbols 3 Considerations
More informationVariable Area Flow Meters and Flow Switches. Easy-to-Use and Reliable Flow Measurement.
Variable Area and Flow Switches Easy-to-Use and Reliable Flow Measurement. Variable Area and Flow Switches The Hedland product line features over 15,000 inline, variable area flow meters to measure oil,
More informationAutomotive Flow Measurement and Control Products
Automotive Flow Measurement and Control Products Control. Manage. Optimize. Automotive Flow Measurement and Control Products When every drop counts, choose automotive flow measurement and control products
More informationProduct Data Sheet. Recordall Fire Series Assemblies (FSAA) Cold Water Meter & Strainer with Disc Bypass DESCRIPTION
Fire Series Assemblies (FSAA) Cold Water Meter & Strainer with Disc Bypass UL Certified & FM Standard Approved for Fire Service Applications NSF/ANSI Standards and Certified DESCIPTION Fire Series assemblies
More informationProduct Data Sheet. Recordall Fire Series Assembly (FSAA) Cold Water Meter & Strainer with Turbine Bypass DESCRIPTION
Fire Series Assembly (FSAA) Cold Water Meter & Strainer with Turbine Bypass UL Certified & FM Standard Approved for Fire Service Applications NSF/ANSI Standards and Certified DESCIPTION Fire Series assemblies
More informationControl Valves. Type HP-10, 10,000 PSI. User Manual. RCV-UM EN-01 (August 2014)
Control Valves Type HP-10, 10,000 PSI RCV-UM-01034-EN-01 () User Manual Control Valves Type HP-10, 10,000 PSI Page ii User Manual CONTENTS Overview...........................................................................
More informationElectronic Preset Meter. Model EPM2-ADV-SF, Advanced Series, Special Fluids. User Manual. AUT-UM EN-05 (August 2015)
Electronic Preset Meter Model EPM2-ADV-SF, Advanced Series, Special Fluids AUT-UM-00916-EN-05 () User Manual Electronic Preset Meter, Model EPM2-ADV-SF, Advanced Series, Special Fluids Page ii AUT-UM-00916-EN-05
More informationProduct Data Sheet. VN2000 Flow Meters. Compact Insertion Meter DESCRIPTION BENEFITS APPLICATIONS INSTALLATION
VN2000 Flow Meters Compact Insertion Meter DESCRIPTION The VN2000 Compact Insertion Vortex Flow Meter measures the volumetric or mass flow rate or BTU/energy of steam, gas or liquids over a large flow
More informationApplication Data Sheet. Chemical Compatibility Chart. IND-AS EN-01 (May, 2014) Metals Plastics Seals KEY. Good. Fair. Ethylene Propylene.
Chemical Compatibility Chart 6 Stainless Acetic Acid Acetone Acetylene Acidic Mine Water Acrylonitrile Ammonium Chloride Ammonium Hydroxide Ammonium Sulfate Ammonium Thio-Sulfate Anhydrous Ammonia Anhydrous
More informationTurbine Flow Sensors. Activa, Ultima, Classic and Quad. User Manual. SEN-UM EN-02 (March 2015)
Turbine Flow Sensors ctiva, Ultima, Classic and Quad SEN-UM-00987-EN-02 () User Manual Turbine Flow Sensors, ctiva, Ultima, Classic and Quad Page 2 User Manual CONTENTS Introduction.........................................................................
More informationUser Manual. Industrial Meters. Oscillating Piston, Sizes 1/2", 1" and 2" Model OP Sanitary (3A Approved) and Model OP Chemical
Industrial Meters Oscillating Piston, Sizes 1/2", 1" and 2" Model OP Sanitary (3A Approved) and Model OP Chemical OPM-DS-00291-EN-03 () User Manual Industrial Meters, Oscillating Piston, Sizes 1/2", 1"
More informationUser Manual. Ellipse Pitot Tube Meter. PFA Fire Pump System. PTT-UM EN-03 (March 2017) 2500 GPM 3000 F M
Ellipse Pitot Tube Meter PFA Fire Pump System 500 GPM 3000 000 3500 1500 1000 PFA-XXX X inch 50 SWP X/XX S/N AXXXXXXX 4000 METERS PTT-UM-0053-EN-03 () User Manual Ellipse Pitot Tube Meter, PFA Fire Pump
More informationIndustrial Meters. Oscillating Piston, Model OP Chemical & Sanitary, Sizes 1/2", 1", 2" User Manual. OPM-UM EN-02 (August 2013)
Industrial Meters Oscillating Piston, Model OP Chemical & Sanitary, Sizes 1/2", 1", 2" OPM-UM-00291-EN-02 (August 2013) User Manual Industrial Meter, Oscillating Piston, Sizes 1/2" through 2" Model OP
More informationProduct Data Sheet. VN2000 Flow Meters. Wafer Plate Inline Meter DESCRIPTION BENEFITS OPERATION APPLICATIONS SIZING SOFTWARE
VN2000 Flow Meters Wafer Plate Inline Meter DESCRIPTION The VN2000 Wafer Plate Inline Flow Meter measures the volumetric or mass flow rate or BTU/energy of steam, gas or liquids over a large flow range.
More informationBIN & SEN Annular Pitot Tube Flow Meter. Form: 10-PTT-UM (December 2012) Installation & Operation Manual
BIN & SEN Annular Pitot Tube Flow Meter Form: 1-PTT-UM-349 (December 212) Installation & Operation Manual Installation Instructions 1. The primary station can be installed in any position on vertical or
More informationProduct Data Sheet. VN2000 Flow Meters. Hot Tap Insertion Meter DESCRIPTION BENEFITS APPLICATIONS INSTALLATION OPERATION SIZING SOFTWARE
VN2000 Flow Meters Hot Tap Insertion Meter DESCRIPTION The VN2000 Hot Tap Insertion Vortex Flow Meter measures the volumetric flow, mass flow rate or BTU/energy of steam, gas or liquids over a large flow
More informationProduct Data Sheet. VN2000 Flow Meters. Hot Tap Insertion Meter DESCRIPTION BENEFITS APPLICATIONS INSTALLATION OPERATION SIZING SOFTWARE
VN2000 Flow Meters Hot Tap Insertion Meter DESCRIPTION The VN2000 Hot Tap Insertion Vortex Flow Meter measures the volumetric flow, mass flow rate or BTU/energy of steam, gas or liquids over a large flow
More informationTurbine Flow Meter. B16N Series FloClean Tri-Clover End Fitting. User Manual. TRB-UM EN-01 (December 2016)
Turbine Flow Meter B16N Series FloClean Tri-Clover End Fitting TRB-UM-02253-EN-01 () User Manual Turbine Flow Meter, B16N Series FloClean Tri-Clover End Fitting CONTENTS Scope of This Manual 3 Unpacking
More informationModel 200 Multi-Jet Flow Meter. 02-PDM-UM (July 2012) Installation & Operation Manual
Model 200 Multi-Jet Flow Meter 02-PDM-UM-00109 (July 2012) Installation & Operation Manual TABLE OF CONTENTS Introduction...3 Operating Principle...3 Specifications...4 Operating Limitations...5 Installation
More informationIndustrial Turbo Meters. Sizes 2 in. through 6 in. User Manual. TUR-UM EN-21 (October 2017)
Industrial Turbo Meters Sizes 2 in. through 6 in. TUR-UM-00530-EN-21 () User Manual Industrial Turbo Meters, Sizes 2 in. through 6 in. Page ii TUR-UM-00530-EN-21 User Manual CONTENTS Scope of the Manual
More informationPFM Portable Hydraulic Testers. PFM6, PFM6BD and PFM8. User Manual. TUR-UM EN-02 (August 2014)
PFM Portable Hydraulic Testers PFM6, PFM6BD and PFM8 TUR-UM-73-EN-2 () User Manual PFM Portable Hydraulic Testers, PFM6, PFM6BD and PFM8 CONTENTS Introduction.........................................................................iii
More informationTurbine Flow Meter B1500. User Manual. TRB-UM EN-02 (June 2016)
Turbine Flow Meter B1500 TRB-UM-01789-EN-02 () User Manual Turbine Flow Meter, B1500 Page ii TRB-UM-01789-EN-02 User Manual CONTENTS Safety information 5 Safety Symbol Explanations 5 Unpacking & Inspection
More informationTurbine Flow Meter. User Manual. Top Load 1 in. and 2 in. Meters. TRB-UM EN-01 (September 2018)
Turbine Flow Meter Top Load 1 in. and 2 in. Meters TRB-UM-02597-EN-01 () User Manual Turbine Flow Meter, Top Load 1 in. and 2 in. Meters CONTENTS Unpacking and Inspection.........................................
More informationRecordall Combo Meter Lead-Free Bronze Alloy, Size 8" (DN 200) NSF/ANSI Standards 61 and 372 Certified RCO-UM EN-02 (October 2013) User Manual
Recordall Combo Meter Lead-Free Bronze Alloy, Size 8" (DN 200) NSF/ANSI Standards 61 and 372 Certified RCO-UM-00077-EN-02 (October 2013) User Manual Recordall Combo Meter, 8" Page ii October 2013 User
More informationProduct Data Sheet. Transit Time Ultrasonic Flow Meters. TFX-500w Clamp-On Meter DESCRIPTION FEATURES BENEFITS OPERATION APPLICATION
Transit Time Ultrasonic low Meters TX-500w Clamp-On Meter ECRIPTION The TX-500w transit time ultrasonic flow meter measures volumetric flow of clean water in pipes 10 in. or smaller. y clamping on the
More informationU500w Ultrasonic Meter. Cold Water Meters. User Manual. ESM-UM EN-04 (September 2017)
U500w Ultrasonic Meter Cold Water Meters ESM-UM-02205-EN-04 () User Manual U500w Ultrasonic Meter CONTENTS About the U500w Ultrasonic Meter 3 Safety Information 3 Product Unpacking and Inspection 3 Meter
More informationVariable Area Flow Meters. Inline Pneumatic Flow Meter. User Manual. VAM-UM EN-02 (August 2014)
Variable Area Flow Meters Inline Pneumatic Flow Meter VAM-UM-00593-EN-02 () User Manual Variable Area Flow Meters, Inline Pneumatic Flow Meter CONTENTS Introduction.........................................................................
More informationUser Manual. Recordall Compound Series Meter. Lead-Free Bronze Alloy, Sizes 2", 3", 4" & 6" NSF/ANSI Standards 61 and 372 Certified
Recordall Compound Series Meter Lead-Free Bronze Alloy, Sizes 2", 3", 4" & 6" NSF/ANSI Standards 61 and 372 Certified RCS-UM-00076-EN-04 (June 2016) User Manual Recordall Compound Series Meter, Lead-Free
More informationFlow-Alert. Flow Switch GPM LPM OIL FLOW-ALERT FLOW SWITCH 6000 PSI / 414 BARS MAX. User Manual. VAM-UM EN-02 (September 2014)
Flow-Alert Flow Switch GPM LPM OIL FLOW-ALERT FLOW SWITCH 6 PSI / 414 BARS MAX VAM-UM-646-EN-2 () User Manual Coriolis Flow Meter, Flow Switch CONTENTS Introduction.........................................................................
More informationInstallation & Operation Manual. Impeller Flow Sensors. IMPORTANT: This manual contains important information. READ AND KEEP FOR REFERENCE.
Impeller Flow Sensors 250 and 228 Metal Tee IMPORTANT: This manual contains important information. READ AND KEEP FOR REFERENCE. 872021-EN (August 2012) Rev. 8 Installation & Operation Manual 250 and 228
More informationVN2000 Flow Meters. Hot Tap Insertion Meter. User Manual. VRX-UM EN-03 (April 2018)
VN2000 Flow Meters Hot Tap Insertion Meter VRX-UM-02217-EN-03 () User Manual VN2000 Flow Meters, Hot Tap Insertion Meter Page 2 VRX-UM-02217-EN-03 User Manual CONTENTS Purpose of this Document................................................................
More informationVortex Flow Meters. Shedding Flow Meter RVL Series. User Manual. VRX-UM EN-03 (April 2017)
Vortex Meters Shedding Meter RVL Series VRX-UM-00371-EN-03 () User Manual Vortex Meters, Shedding Meter Page ii VRX-UM-00371-EN-03 March 2017 User Manual CONTENTS Description 5 Operating Principle 5 Fluids
More informationWATER METER MATERIAL & ORDER INFORMATION
WATER METER MATERIAL & ORDER INFORMATION Supplier Contact: National Meter & Automation, Inc. PO Box 8339 2250 Apollo Way #300 Santa Rosa, CA 95407 Kathy Richards Phone 707/575 0700 Fax 707/575 3786 Toll
More informationSeries TFXL ULTRASONIC CLAMP-ON FLOW METER DIMENSIONAL SPECIFICATIONS PRODUCT INSTALLATION
Series PROUT INSTLLTION Series IMENSIONL SPEIFITIONS MEHNIL IMENSIONS: INHES (MM) Installation onsiderations 1. Select the optimum mounting location on the piping system a full pipe with at least 10 straight
More informationThermostatic Valve. Filterstat - Model FJA. Typical applications. Key features and benefits. Mixing Diverting
Thermostatic Valve Filterstat - Model FJ Typical applications Mixing Diverting Key features and benefits Direct filter connection Integral differential pressure switch Integral oil filter manifold Mount
More informationUser Manual. Intrinsically Safe Flow Meters. RWG/RWBG Wafer Style Flow Meters RNG Insertion Style Flow Meters. VRX-UM EN-03 (October 2014) Flow
Intrinsically Safe Meters RWG/RWBG Wafer Style Meters RNG Insertion Style Meters FLOW VRX-UM-00374-EN-03 () User Manual Intrinsically Safe Meters, RWG/RWBG Wafer Style Meters & RNG Insertion Style Meters
More informationPrecision Flow Measurement Solutions. Test and Measurement
Precision Flow Measurement Solutions Test and Measurement Introduction Badger Meter is a leading innovator, manufacturer and marketer of flow measurement and control products, serving water and gas utilities,
More informationPFM Portable Hydraulic Testers. PFM6, PFM6BD, and PFM8. Badger Meter. Installation & Operation Manual. 05-TUR-UM EN (September 2012)
PFM Portable Hydraulic Testers PFM6, PFM6BD, and PFM8 Badger Meter 5-TUR-UM-193-EN (September 12) Installation & Operation Manual Page ii September 12 CONTENTS INTRODUCTION 5 PFM6 Digital Hydraulic Tester
More informationFlow Sensors. Series 228PV PVC Tee Type Flow Sensors. User Manual. SEN-UM EN-10 (February 2018)
Flow Sensors Series 228PV PVC Tee Type Flow Sensors SEN-UM-01664-EN-10 () User Manual Flow Sensors, PVC Tee Type Flow Sensors CONTENTS Introduction.........................................................................
More informationIndustrial OG meter series IOG Inline and flanged oval gear meter
Badger Meter Europa GmbH Nürtinger Str. 76 72639 Neuffen (Germany) Tel. +49-7025-9208-0 Fax +49-7025-9208-15 www.badgermeter.de badger@badgermeter.de Industrial OG meter series IOG Inline and flanged oval
More informationPaddle Wheel Flow Meter
www.fine-tek.com Paddle Wheel Meter FineTek Lab FineTek is the company who owns a Second lass flow test laboratory in Taiwan. With the most professional R& team, FineTek develops various high precision
More informationPRECISION METERS. Tel: / Int'l: Fax: / Int'l: Springer Pumps, LLC Telford, PA 18969
PRECISION METERS Sotera Precision Meters incorporate oval gear technology, eliminating metal-to-metal contact within the measuring chamber. This unique design promotes minimal wear, sustained accuracy,
More informationSmith Meter Truck Meter Packages Specifications
Issue/Rev. 0.4 (8/12) P Meter Smith Meter Truck Meter Packages Specifications ulletin SS01095 TP (Ticket Printer) LN (Large Numeral ounter) Preset ounter Air Eliminator/ Strainer Faucet P Meter Smith Meter
More informationLiquid Turbine Flowmeters
NUFLO Liquid Turbine Flowmeters Accurate Flow Measurement In 1957, this flowmeter was developed with a tungsten-carbide shaft and bearing to withstand the rugged conditions of the oil field. Over the years,
More informationFlow-Alert Flow Switch
Flow-Alert Flow Switch GPM LPM OIL FLOW-ALERT FLOW SWITCH 6000 PSI / 414 BARS MAX FORM #04-VAM-UM-00229 (September 2012) Installation & Operation Manual I - INTRODUCTION The Flow-Alert flow meter combines
More informationModel G6-S3. Repeatability ±0.02%
Issue/Rev. 0.6 (2/07) Smith Meter TM PD Rotary Vane Meter 6" Steel Model G6 Specifications Bulletin SS01014 The Smith Meter TM Model G6 Meter is a 6", double-case, straight-through (S3 through S8) or angle-type
More informationBARTON 7000 Series Liquid Turbine Meters
TECHNICAL SPECIFICATIONS BARTON 7000 Series Liquid Turbine Meters Cameron s BARTON 7000 series turbine meters are designed for a broad range of precise liquid measurement applications. Based on more than
More informationElectromagnetic amplifier type ModMAG M10 for all detectors
Badger Meter Europa GmbH Nürtinger Str. 76 72639 Neuffen (Germany) Tel. +49-7025-9208-0 Fax +49-7025-9208-15 www.badgermeter.de badger@badgermeter.de Electromagnetic amplifier type ModMG M10 for all detectors
More informationHydraulic Motor & Brake
SERIES 500-501 - 510-511 - 520-521 - 530-531 - 50-51 - MEDIUM DUTY Hydraulic Motor & rake RE RE (ll Series) For Medium Duty pplications Overview series descriptions RE Series motors offer the perfect compromise
More informationFOR BOARD-TO-CABLE CONNECTION
FOR OR-TO-LE ONNETION 240 SERIES (GENERL-PURPOSE TYPE) FETURES 1.27 mm (0.050 in.) pitch contact arrangement in two rows enables high-density mounting. onnectors with 20 to 96 contacts are available for
More informationHTTF Transit Time Ultrasonic Flow Meter
Installation onsiderations imensional Specifications 1. Select the optimum mounting location on the piping system a full pipe with at least 10 straight pipe diameters upstream and 5 pipe diameters downstream
More informationTorque Sensor. Torque. Mini-Smart Torque Sensor. Type 4502A...
Torque Torque Sensor ini-smart Torque Sensor 4502... 4502... torque sensors operate on the strain gage principle and supply an analog output signal of ±0... 5 V which is contactless transferred. vailable
More informationG2 SERIES INDUSTRIAL GRADE METERS
Industrial Grade Meters INDUSTRIAL GRADE METERS The unique modular approach of the Industrial Grade Meter line allows you to design a meter to match your specific application. Turbine choice depends on
More informationISO 9001 : Full Port Check Valves. Male NPT, Plain & Grooved End Lowest Pressure Drop. Maximizing the Flow
ISO 9001 : 2008 Full Port heck Valves Male NPT, Plain & Grooved End Lowest Pressure Drop Maximizing the Flow Full Port Lowest Pressure Drop Quick Delivery Full Port, Lowest Pressure Drop Full Port heck
More information1-14 Fittings and Accessories
-4 ittings and ccessories entricast Piping Systems NOV iber Glass Systems offers a complete line of fittings manufactured from both epoxy and vinyl ester resins. These fittings and adhesives provide the
More informationFEATURES. 3 position models can be equipped with special 180 operators offering two 90 steps.
2" 8" (DN 50 200) OTTOM PORTED 3-WY FLNGED LL VLVES Jamesbury bottom ported 3-way ball valves provide a variety of flow paths not commonly found in other 3-way designs.the basic design is suitable for
More informationSAE J1939 CAN compatible sensors for hydraulic system monitoring of flow, pressure and temperature on pumps, valves and hydrostatic transmissions
SAE J99 CAN compatible sensors for hydraulic system monitoring of flow, pressure and temperature on pumps, valves and hydrostatic transmissions Milwaukee, WI, USA Tel: + () 769-600 sales-us@webtec.com
More information9400 Series Oval Flowmeter
Design Specifications DS9400 Revision 03 9400 Series Oval Flowmeter High accuracy Simple, durable construction Low maintenance requirements Easy access 3 piece design Choice of materials of construction
More informationYour Global Source for Today s Most Popular Solenoid Valves
lcon Solenoid Valves Your Global Source for Today s Most Popular Solenoid Valves lcon Solenoid Valves Your Global Source for Today s Most Popular Solenoid Valves lcon Solenoid Valves, a division of International
More informationwhitedriveproducts SERIES Hydraulic Motor LIGHT DUTY
whitedriveproducts SERIES 275-276 - 277-278 - 280-281 - LIGHT DUTY Hydraulic Motor www.cenhyd.com 1(800)264-9571 WG WG (ll Series) For Light Duty pplications whitedriveproducts overview The White Drive
More informationType 2712 (8630) Continuous TopControl System. General data Compatibility Materials of wetted parts Body Rotor Shaft Seal
Positive displacement flow fitting for continuous and batch control High accuracy ± 0.5% 1/2 TO 4 (DN 15 to 100) INLINE Quarter Turn technology For highly viscous fluids Electronics for indication, monitoring,
More informationNorth. Asia. America. Africa. South. America. Australia. Double Block and Bleed Dual Expanding Plug Valve
North merica Netherlands Europe sia frica South merica ustralia ouble lock and leed ual Expanding Plug Valve CERTIFICTES E X E CUT IO NS V Standard Execution 35 33 7 13 11 6 21 56 12 30 2 7 32 17 23 5
More informationLiquid Turbine Flowmeters
MEASUREMENT SYSTEMS NUFLO Liquid Turbine Flowmeters Accurate Flow Measurement NuFlo developed its first flowmeter for oilfield applications in 1957. The meter incorporated a tungsten-carbide shaft and
More informationProduct Information / Order Code
Product Information / Order ode Order odes eries and Type low onitoring ystem G - 0.04 - - 1 - V - X G Version 0,002... 2 l/min / 0.0005... 0.53 U GP 0.02 0,004... 4 l/min / 0.0011... 1.06 U GP 0.04 0,01...
More informationFOR BOARD-TO-CABLE CONNECTION
FOR OR-TO-LE ONNETION 230 SERIES (GENERL-PURPOSE TYPE) ISONTINUE FETURES 1.27 mm (0.050 in.) pitch contact arrangement in two rows enables high-density mounting. onnectors with 20 to 80 are available for
More informationFEATURES SPECIFICATIONS
RS 1 FETURES 2 3 1 High Pressure Viton Shaft Seal offers superior seal life and performance and eliminates the need for case drain. 2 Pressure Fed earing surface receives positive flow of clean, cool oil.
More informationOMP Positive Displacement Flowmeters
Flow Ranges From 0.53 to 26 GPH Through 4 to 132 GPH Handles Viscosities to 1,000,000 cps Handles Viscosities to 1,000,000 cps Low Head Loss Oval Gear Design OMP Series Medium & High Flow Meters OMP-1
More informationVG4000 Series. High-Capacity/High-Closeoff Electric Zone Valves
Product ulletin VG000 Issue ate 11/01/01 VG000 Series High-apacity/High-loseoff Electric Zone Valves VG000 Series High-apacity/High-loseoff Electric Zone Valves are designed to regulate the flow of water
More informationModel DFX Doppler ultrasonic flow meter
Badger Meter Europa GmbH Nürtinger Str. 76 72639 Neuffen (Germany) Tel. +49-7025-9208-0 Fax +49-7025-9208-15 www.badgermeter.de badger@badgermeter.de Model DFX Doppler ultrasonic flow meter Features Badger
More informationTM 301 TM 308 In-Line Torque Transducers
ata Sheet In-Line Torque Transducers Features Integrated Torque and Speed onditioning Torque Range: 0.1 N m to 20 N m (0.07 lb ft to 15 lb ft) ccuracy: < 0.1% Overload apacity: 200% Overload Limit: 400%
More information6" Steel Model G6. Smith Meter Rotary Vane PD Meters. Features. Operating Specifications Maximum Flow Rate. Options
SPECIFICATIONS 6" Steel Model G6 Bulletin SS01014 Issue/Rev. 1.0 (4/18) Smith Meter Rotary Vane PD Meters The Smith Meter Model G6 Meter is a 6", double-case, straight-through rotary vane type positive
More informationDTK. OEM Pelton Wheel Flow Sensor
OEM Pelton Wheel Flow Sensor measuring monitoring analyzing DTK Measuring Range: 0.8...9.5 to 6...90 GPH Water Measures Clear or Opaque Liquids Stainless Steel Body Pelton Wheel Design Requires No Inlet
More informationFisher 1052 Size 70 Diaphragm Rotary Actuator
1052 Actuator Product Bulletin Fisher 1052 Size 70 iaphragm Rotary Actuator Fisher 1052 size 70 spring return diaphragm rotary actuators operate splined shaft rotary valves, such as 8580, 852, 8590, V500,
More informationOMP POSITIVE DISPLACEMENT FLOWMETERS
OMP POSITIVE DISPLACEMENT FLOWMETERS Flow Pressure Level Temperature measurement monitoring control Flow Ranges from 0.53 to 26 GPH to 4 to 92 GPM Handles Viscosities to 1,000,000 cps Pressure Ratings
More informationSILVER STREAK FITTINGS DIMENSIONS
SILVER STREK FITTINGS DIMENSIONS Silver Streak piping and fittings are designed especially for abrasive and corrosive services such as limestone and gypsum slurries, found in flue gas desulfurization (FGD)
More informationVickers. Service Data. Vane Pumps. Vane Type Triple Pump (F3) 2520VQSV10* ***** ******* 20* M 2492 S. Released
Service ata Vickers Vane Pumps Vane Type Triple Pump (F3) 2520VQSV10* ***** ******* 20* Released 08 01 95 M 2492 S 10 SE rated capacity (V10 cover end cartridge) USgpm Rotor Vane Kit Ring Pin Pin olt olt
More informationVickers. Service Data. Vane Pumps. Vane Type Triple Pump (F3) 4525VQSV10* ***** ******* 20* Released M 2496 S
Service ata Vickers Vane Pumps Vane Type Triple Pump (F3) 4525VQSV10* ***** ******* 20* Released 08 01 95 M 2496 S 10 SE rated capacity (V10 cover end cartridge) USgpm Rotor Vane Kit Ring Pin Pin olt olt
More informationPSF50 Paddle flow switch
Paddle Flow Switch Paddle Flow Switch PSF50 Paddle flow switch Paddle flap flow / no flow switch Economically priced flow/no flow paddle operated flow switch. Simple and reliable design for liquids up
More information3" Steel Model E3. We put you first. And keep you ahead.
SPECIFICATIONS MEASUREMENT SOLUTIONS 3" Model E3 Bulletin SS01016 Issue/Rev. 1.1 (2/15) We put you first. And keep you ahead. SMITH METER PD METERS The Smith Meter Model E3 is a 3", double-case, straightthrough
More informationInstallation & Operation Manual. IMPORTANT: This manual contains important information. READ AND KEEP FOR REFERENCE.
Elecronic Preset Meter 2 Industrial Handheld Series Model EPM2-IND Standard Series IMPORTANT: This manual contains important information. READ AND KEEP FOR REFERENCE. IOM-139-02-EN (1-12) 53400-139 Rev.
More informationwhitedriveproducts SERIES Hydraulic Motor LIGHT DUTY
SERIES 0-1 - LIHT DUTY Hydraulic Motor RS RS (ll Series) For Light Duty pplications Overview RS Series motors are the most economical model in the White Drive Products product line, but are not low-tech.
More informationTorque Sensor. Torque. Mini-Smart Torque Sensor. Type 4502A...
Torque Torque Sensor ini-smart Torque Sensor 4502... 4502... torque sensors operate on the strain gage principle and supply an analog output signal of ±0... 5 V which is contactless transferred. vailable
More informationMTX and WPX Turbine Flowmeters
Principle of Operation Liquid enters the precision metering insert containing the turbine rotor. The liquid pressure drives the turbine rotor rate of rotation proportional to the volumetric flow rate.
More informationRS Series. Three way rotary valves for temperature control systems
RS Series Three way rotary valves for temperature control systems R S RS Three way rotary valve for temperature control systems RS 3-way rotary valve for temperature control systems High Efficiency Mixing
More informationTechnical Data. BiRotor Plus Positive Displacement Meter
Technical Data BiRotor Plus Positive Displacement Meter B27X 3 ANSI (DN80) B30X 6 ANSI (DN150) B28X 4 ANSI (DN100) B31X 8 ANSI (DN200) B29X 6 ANSI (DN150) B32X 10 ANSI (DN250) General The BiRotor Plus
More informationR EGI S TERED. Function
Z series zone valves R EGI S TERE S EN ISO 900:000 ert. n FM 64 UNI EN ISO 900:000 ert. n 0003 LEFFI 0/09 N Replaces 0/04 N Function Z-one valves are used to automatically shut-off the flow or redirect
More information