SILVER STREAK FITTINGS DIMENSIONS

Transcription

1 SILVER STREK FITTINGS DIMENSIONS Silver Streak piping and fittings are designed especially for abrasive and corrosive services such as limestone and gypsum slurries, found in flue gas desulfurization (FGD) scrubber applications. Silver Streak piping systems are designed to operate at temperatures up to 225 F and pressures up to. ll bell end and assembled flanged* Silver Streak fittings are rated for service up to. complete line of standard long-radius fittings are available. Odd degree elbows are available on special order. Fittings are constructed with the same abrasion-resistant additives as the pipe. ll fittings, except compression molded, have a nominal corrosion/abrasion barrier of 100 mils. 90 Elbow ELL x ELL FLNGE x FLNGE 45 Elbow ELL x ELL FLNGE x FLNGE 150 psig X (1) x F x F * * * * * psig X (1) x F x F * * * * * = ELL F=FLNGE (1) This is a nominal make-up dimension for drawing layout work only. Do not use for assembly dimensions. * Special Order fgspipe@nov.com

2 Tee ELL x ELL x ELL FLNGE x FLNGE x FLNGE Sleeve Coupling ELL x ELL NOTE Couplings: If coupling length is critical for a piping system design, please specify dimension when ordering. 150 psig X (1) x x X (2) F x F x F * * * * * Max. Operating (psig) x Nipple Nipple Length = ELL F=FLNGE Standard stock. (1) This is a nominal make-up dimension for drawing layout work only. Do not use for assembly dimensions. * Special order. 2

3 Flange Pipe Size C CC (1) D E O X (1) Max. Operation (psig) Flange lind Flange Flange lind Flange D-4 holes D-4 holes D-8 holes D-8 holes D-8 holes D-12 holes D-12 holes D-12 holes D-16 holes D-16 holes D-20 holes D-20 holes Note: ll flanges are NSI lb. olt Hole Circle. (1)Steel back-up plates must be used to achieve pressure ratings equivalent to the pipe. Reducer Size Max. (psig) X1 (1) X2 (1) x F x F Concentric Reducer ELL x ELL FLNGE x FLNGE 3 x * x * x * x * x * x * x * x * x * x * x * x x x x x x x x * x * x * x * x * x * * Nipples and flanges (1) This is a nominal make-up dimension for drawing layout work only. Do not use for assembly dimensions. 3

4 Saddles Size ngle C X Steady Rating In. In. In. Degree In. psi 2x x1½ x x1½ x x x1½ x x x x1½ x x x x x x x x x x x x x x x x x x

5 Saddles, Cont d. Size ngle C X Steady Rating In. In. In. Degree In. psi 14x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x

6 REDUCING TEES (1) This is a nominal make-up dimension for drawing layout work only. Do not use for assembly dimensions. X1 X2 Nom. Nom. Size X1 (1) X2 (1) Wgt. Steady In In In In In Lbs psig 8x x x x x x x x x x x x x x x x x x x x Laterals, crosses, and eccentric reducers available upon request. ll dimensions listed in this bulletin are nominal in nature and should only be used for system layout and take off. ctual fittings and fabrication work should be measured before bonding to ensure dimensional accuracy. Fiber Glass Systems does not warrant and is in no way responsible for the workmanship of any distributor, contractor or others involved in the installation of the goods. National Oilwell Varco has produced this brochure for general information only, and it is not intended for design purposes. lthough every effort has been made to maintain the accuracy and reliability of its contents, National Oilwell Varco in no way assumes responsibility for liability for any loss, damage or injury resulting from the use of information and data herein nor is any warranty expressed or implied. lways cross-reference the bulletin date with the most current version listed at the web site noted in this literature. North merica South merica Europe sia Pacific Middle East San Pedro ve. Suite 200 venida Fernando Simoes P.O. ox 6, 4190 C No. 7, Tuas venue 3 P.O. ox San ntonio, Texas US Recife, razil Geldermalsen, The Netherlands Jurong, Singapore Dubai, UE Phone: Phone: Phone: Phone: Phone: fgspipe@nov.com 2012 National Oilwell Varco. ll rightss reserved. CI December 2010