Tech. Services: (800) Fax: (800) Order Entry: (800) Fax: (800)

Size: px

Start display at page:

Download "Tech. Services: (800) Fax: (800) Order Entry: (800) Fax: (800)"

MargaretMargaret Morrison
5 years ago
Views:

1 Parts List for: Form No. 068 SPX Corporation 88 th Street Rockford, IL USA Internet Address: Tech. Services: (800) Fax: (800) Order Entry: (800) -8 Fax: (800) PA6R-MILL MODEL F AIR HYDRAULIC PUMP Max. Capacity: 0,000 PSI (700 Bar) 2 *8 Reservoir Gasket 2 62 Reservoir *09 Decal 20 Straight Fitting Hex Washer Hd Screw (#9- X " Lg.; Torque to 2/ in. lbs.) PARTS INCLUDED BUT NOT SHOWN 2060 Hex Washer Hd Screw (#9- X " Lg.; For pump mounting purposes only) Part numbers marked with an asterisk (*) are contained in Repair Kit No Sheet No. of Litho in USA Rev 8 Date: Nov 200

2 Parts List, Form No. 068, Back sheet of TOP AND END VIEW, 2 0 8, Apply Permatex between gasket and cover plate 6 2 Soc. Hd. Cap Screw (0-2 UNC X /2 Lg.) Washer (#0 bolt) 20 Straight Fitting 2096BK2 Cover Plate 6 Soc. Hd. Cap Screw (0-2 UNC X -/" Lg.; Torque to 0/60 in. lbs.) Valve Body Release Valve Body 8 20 Elbow Plastic Cap Filler/Breather Cap *027 2 O-ring (/6 X /8 X /2; Nitrile) Pump Body 728 Soc. Hd. Cap Screw (/-20 UNC X -/2" Lg.; Torque to 8/9 in. lbs. oiled; NOTE: Cross torque in increments of 0 in. lbs.) Part numbers marked with an asterisk (*) are contained in Repair Kit No

3 Parts List Form No. 068 BASIC PUMP ASSEMBLY To Parts List 9 0 See Detail "A" , , ; See Detail "B" 6 DETAIL "B" Sheet No. 2 of Rev 8 Date: Nov 200

4 Parts List, Form No. 068, Back sheet 2 of 77 Piston Release 2 *208 O-ring (-/8" X 7/8 X /8; Apply Lubricant) *0272 O-ring (/ X 9/6 X /2; Nitrile) 78 Check Valve Body *222 2 O-ring (/8 X / X /6; Urethane) 6 *8 O-ring (-/8" X -/8" X /8; Nitrile) 7 *02 Gasket 8 *02 Washer (/8 X / X /2) Soc. Hd. Cap Screw (/-20 UNC X /8 Lg.; Torque to 90/0 in. lbs.) 0 *0 Compression Spring (/2 O.D. X / Lg.) *02 Steel Ball (9/2 Dia.) Relief Valve (Apply loctite 92 [Power Team #906] or equiv. & torque to 0/70 in. lbs.) 278 Piston Cylinder (Torque to 90/00 ft. lbs. oiled) *07 Steel Ball (/ Dia.) *026 Copper Washer (/ X 9/2 X /2) Filter Adapter Filter Internal Retaining Ring 9 *026 Copper Washer (" X.76 X /2) 20 2 *9 *029 U-cup & Backup Retainer (Note: See INSTRUCTIONS FOR RETAINER REPLACEMENT on back sheet of.) 22 *729 2 Back-up Ring (2-/6" X 2-/" X.0) 2 *98 Compression Spring (.2 O.D. X -7/6" Lg.) Piston 2 20 Bumper Spring Guide 27 7 Air Cylinder (NOTE: Locate groove on upper half (top) of pump with chamfered tube end towards rear head as shown.) 28 *2692 Compression Spring (/6 O.D. X -/6" Lg.) 29 *202 O-ring (.900 X.706 X.097; Nitrile) 0 07 Exhaust Valve Stem *02 Lockwasher (For #0 bolt) 2 20 Screw (#0-2 X /2 Lg.; Torque to 0/ in. lbs.) 822 Piston End Plate *288 Piston Poppet *20679 Compression Spring (.8 O.D. X.9 Lg.) 6 *2067 Hex Soc. Flat Hd. Cap Screw (8-2 UNC X /8 Lg.; Torque to 2/8 in. lbs.) Rear Head 8 *26296 Filter Disc 9 *206 Muffler 0 *2829 Gasket 290 Piston Body 2 *26 2 Piston Ring *28 2 O-ring (2-/2" X 2-/6" X /2; Nitrile) *0276 O-ring (" X / X /8; Nitrile) To Drawing Part numbers marked with an asterisk (*) are contained in Repair Kit No

5 Parts List Form No. 068 DETAIL A 2 Seat at ass'y Release Valve Button 2 *0266 O-ring (/8 X / X /6; Nitrile) *9 Spring 77 Poppet Retainer *279 O-ring (/2 X /8 X /6; Nitrile) 6 97 Dowel Pin (NOTE: Place tapered end toward ball.) Release Valve Body 8 * Steel Ball (/2 Dia.) Ball Retainer 0 *99 Compression Spring (/8 O.D. X /2 Lg.) Part numbers marked with an asterisk (*) are contained in Repair Kit No Refer to any operating instructions included with this product for detailed information about operation, testing, disassembly, reassembly, and preventive maintenance. Items found in this parts list have been carefully tested and selected. Therefore: Use only genuine Power Team replacement parts! Additional questions can be directed to our Technical Services Department. Sheet No. of Rev 8 Date: Nov 200

6 Parts List, Form No. 068, Back sheet of INSTRUCTIONS FOR RETAINER REPLACEMENT Your pump's retainer is locked into place by one of the two following methods. Determine which method was used on your pump's retainer, then follow the appropriate steps to remove the old and install and stake the new. Method - Retainer shows no sign of stake marks. This retainer has been locked in place with a Loctite product. To replace it, a moderate amount of heat needs to be applied to the cylinder nut (in the area of the retainer) to soften the existing Loctite allowing it to be removed. 2. Install the new retainer into the cylinder nut and torque to 80/00 in. lbs. Note: Do not use a Loctite product this time but stake the new retainer in place according to instructions in Step.. To lock retainer into place, use a center punch positioned in the seam between the retainer and the cylinder nut and stake the new retainer in two places approximately 80 apart. Method 2 - Retainer has two stake marks in the seam between the retainer and the cylinder nut. For replacement of this retainer, the stake marks must be removed. Using a /8" or larger diameter drill bit, remove the existing stakes by drilling a short distance into the stake marks. Remove the retainer. 2. Install the new retainer into the cylinder nut and torque to 80/00 in. lbs.. To lock retainer into place, use a center punch positioned in the seam between the retainer and the cylinder nut and stake the new retainer in two places approximately 80 apart. NOTE: Do not stake in the old stake marks. Thread seam Cylinder nut Retainer Stake marks No stake marks

Form No , 3, 4. Parts List for: MODEL F AIR HYDRAULIC PUMP. Maximum Capacity: 10,000 PSI. Item Part No. No. No.

Form No , 3, 4. Parts List for: MODEL F AIR HYDRAULIC PUMP. Maximum Capacity: 10,000 PSI. Item Part No. No. No. SPX Corporation Eisenhower Drive Owatonna, MN 00-099 USA Phone: (0) -000 Tech. Services: (800) 33- Fax: (800) 9-839 Order Entry: (800) 33- Fax: (800) 83-8 International Sales: (0) -90 Fax: (0) -03 Parts