ELECTRIC HYDRAULIC PUMP

Transcription

1 Form No SPX Corporation 88 11th Street Rockford, IL USA Internet Address: Tech. Services: (800) Fax: (800) Order Entry: (800) Fax: (800) Parts List for: MODEL B ELECTRIC HYDRAULIC PUMP 17 "A" "A" STOP START 1 RUN JOG Basic Pump Assembly See back sheet 2 of BRACKET BRACE COVER HANDLE NOTE: Place lockwasher between each layer of sheet metal at each screw location. 10 SECTION "A-A" Sheet No. 1 of Litho in USA Rev. 3 Date: 10 April 2001

2 Parts List, Form No , Back sheet 1 of Item Part No. No. No. Req d Description 1 313BK2 1 Handle Decal Decal 160 Steel Washer (For 1/ Bolt) 31BK2 1 Mount Bracket Washer (For 1/ Bolt) Hex Nut (1/-20 UNC) Gasket Key Washer (1/ External Tooth) PU2 1 Reservoir Cap Screw (3/8-16 X 1" Lg.; Torque to 90/100 in. lbs.) Motor Base Gasket V-ring 1 31BK2 1 Brace Electric Motor BK2 1 Cover PARTS INCLUDED BUT NOT SHOWN Coupler HYDRAULIC SCHEMATIC M MAX. PRESSURE SAFETY RELIEF VALVE,00 P.S.I. AUTOMATIC DUMP VALVE HP PRESSURE SWITCH 3,0 P.S.I. LP TO VALVE SUPERCHARGE RELIEF VALVE 270 P.S.I. EXTERNAL PRESSURE REGULATOR 3,0 P.S.I.

3 Parts List Form No TOP VIEW 11, , 1 16 RETURN RE 17 Motor Contol Assembly See sheet of Item Part No. Item Part No. No. No. Req d Description No. No. Req d Description Hex Nut (1/2-13 UNC) Tube Handle Handle Grip Decal CSA Decal Cap Screw (1/-20 UNC X 3/ Lg.) Elbow Pressure Gauge Trade Name Decal Plastic Plug Manifold Drain Tube Cap Screw (1/-20 UNC X 1-1/ Lg.) Bushing Locknut Cap Screw (1/-20 UNC x 3/ Lg.) Bolt Decal Sheet No. 2 of Rev. 3 Date: 10 April 2001

4 Parts List, Form No , Back sheet 2 of BASIC PUMP ASSSEMBLY SIDE VIEW , Item Part No. Item Part No. No. No. Req d Description No. No. Req d Description O-ring (7/16 X /16 X 1/16) Body Compression Spring (1/ O.D. X 3/ Lg.) Steel Ball (1/ Dia.) Bearing Top Plate Ball Bearing Top Plate Needle Bearing Bearing Race Angle Plate Thrust Bearing Bearing Race Plug (Torque to 3/ in. lbs. oiled) Ball Bearing Gerotor Set Wear Plate Seal Washer (Turn on - Do not push on) Nut (1/2-20 UNF) Intake Tube O-ring (1/2 X 3/8 X 1/16) Backup Washer (1/2 X 3/8 X 1/16) Spacer Valve Connector (Note: Torque valve connector [Item #23] to 20/30 ft. lbs. into cover plate. Hold valve connector and torque tube nut [Item #2] to 0/0 ft. lbs.) Tube Sleeve Tube Nut Oil Line Tube

5 Parts List Form No BASIC PUMP ASSEMBLY BOTTOM VIEW Cross torque in 20/30 in. lb. increments in order shown SECTION VIEW Sheet No. 3 of Rev. 3 Date: 10 April 2001

6 Parts List, Form No , Back sheet 3 of Item Part No. No. No. Req d Description Valve Adjusting Screw Nut (3/8-2 UNF) Valve Cap Spring Guide O-ring (1/2 x 3/8 x 1/16) Compression Spring (1/2 O.D. X 1-/8 Lg.) Valve Body Valve Stem Tube Elbow Connector Single Cross Fitting Elbow Cap Screw (1/-20 X " Lg.; Torque to /6 in. lbs.) Spacer Pipe Nipple Cover Plate Strainer Pressure Regulator Tube Air Bleed Valve Pump Body Ass'y Relief Valve Refer to any operating instructions included with this product for detailed information about operation, testing, disassembly, reassembly, and preventive maintenance. Items found in this parts list have been carefully tested and selected. Therefore: Use only genuine Hytec replacement parts! Additional questions can be directed to our Technical Services Department.

7 Parts List Form No HIGH PRESSURE PUMP ASSEMBLY SECTION SECTION Sheet No. of Rev. 3 Date: 10 April 2001

8 Parts List, Form No , Back sheet of Item Part No. No. No. Req d Description Piston 2 29 Ball Guide Barrel Ball (3/16 Dia.) Valve Head End Plate Screw (Torque to 170 in. lbs.; Note: Lubricate under head and on threads.) O-ring (1/ X 1/8 X 1/16) Cylinder Valve Piston Machine Screw (1/-20 UNC x 1-1/2 Lg.) Compression Spring (1/ O.D. X /8 Lg.) Nut (3/8-2 UNF) Adjusting Screw Adapter Steel Ball (1/ Dia.) Compression Spring (/8 O.D. X 3/ Lg.) Replaceable Seat Steel Ball (/32 Dia.) Washer (3/8 X 1/ X 1/32) Screw (Torque to 180 in. lbs.) Copper Washer (9/16 X 3/8 X 1/32) Compression Spring (3/16 O.D. X 3/ Lg.) Pin Sleeve Compression Spring (/32 O.D. X 3/ Lg.)

9 Parts List Form No Notch Tab Power Cord Ground (must be isolated between nuts and can be at top or bottom of stack.) GRD-1 Rubber Washer Assemble to back of push button. Plastic Keyed Sealing Washer Note: Assemble plastic keyed sealing washer to pushbutton so that tab engages notch in washer. Rotate rubber washer if req. 3 Note: Serrated lockwasher must be adjacent to metal box. More washers can be used if desired. SECTION 1, RUN JOG 2 2 FU 7, 23 T 21 See Detail "B" 20 GRD GROUND 12, , , (METAL SWITCH GUARD) CONTROL BOX 26 HEX. NUT INTERNAL TOOTH LOCK WASHER ADV HOLD REV RUBBER BUSHING SEAL 1 DETAIL "B" MOTOR CONTROL ASSEMBLY Sheet No. of Rev. 3 Date: 10 April 2001

10 Parts List, Form No , Back sheet of Item Part No Item Part No. No. No. Req d Description No. No. Req d Description Fuse Holder Fuse Screw (10-2 UNC X 3/ Lg.) Lockwasher (#10 External Tooth) Nut (#10-2 UNC) Transformer Machine Screw (#10-2 UNC X 3/8 Lg.) Machine Screw (#10-2 UNC X 1/2 Lg.) Contactor Plug Pressure Switch Cable (18/2 SJTO) Bushing Locknut Hand Switch Assembly (See Form No. 1016) Cord Set (For 11 V.; Model ) ft. Electrical Cable (1/3 SJTO: For 230 V.; Model ) Electrical Plug (For 230 V.; Model ) Bushing Decal Ground Decal ft. Electrical Cable (1/ SJOW) Seal Toggle Switch Decal (RUN - JOG) Pushbutton Switch Pushbutton Switch Control Box Assembly Metal Switch Guard ELECTRICAL SCHEMATIC WARNING: To help avoid personal injury, all electrical work must be done by a qualified electrician. L1 P1 P2 L2 L3 H1 11 V. H3 H2 H M T8/J10 T3 T2 T T MTR Note: Shaded areas reflect last revision(s) made to this form. X1 X2 T MOTOR CONNECTIONS FOR 11 V. FU 1.2A 2V. GRD PB1 (STOP) PB2 (START) JOG M2 MTR P1 P2 T8/J10 T3 T2 PGT-9 PGT-8 W2-1 W2-3 ON TGS PS (N.O. HELD CLOSED) M GRD-2 T T PGT-7 W2- W2-2 REMOTE SW Transformer connections are for 11 V., 60 Hz. as shown For 230 V., 60 Hz. units, transformer connections to be as follows: H1 TO L1 H2 TO H3 H TO L2 MOTOR CONNECTIONS FOR 230 V. P1 PGT-9 W2-1 P2 W2-3 PGT-8 T8/J10 MTR T3 PGT-10 T2 T PGT-7 W2-2 T GRD-2 W2-