1:8 SCALE GAS POWERED OFF-ROAD BUGGY BLACK EDITION WITH 14MM SHOCKS

Size: px

Start display at page:

Download "1:8 SCALE GAS POWERED OFF-ROAD BUGGY BLACK EDITION WITH 14MM SHOCKS"

Augustine Blair
5 years ago
Views:

SUPPLEMENTAL MANUAL 1:8 SCALE GAS POWERED

KEEP THIS MANUAL FOR PARTS NUMBERS WHEN ORDERING.

1 SUPPLEMENTAL MANUAL 1:8 SCALE GAS POWERED OFF-ROAD BUGGY BLACK EDITION WITH 14MM SHOCKS TQ Sport INSTRUCTION MANUAL PLEASE READ INSTRUCTIONS CAREFULLY BEFORE ASSEMBLING THIS MODEL. KEEP THIS MANUAL FOR PARTS NUMBERS WHEN ORDERING. REV SPECIFICATION ARE SUBJECT TO CHANGE WITHOUT NOTICE.

REQUIRED FOR OPERATION THINGS NEED BESIDES THE KIT 3.

95 (please note OFNA Glow Heats available) Glow Fuel 20% Bottle s with spout # 10160 - large 500cc # 10161 - large 500 ccauto Stop # 10162 - small

Off-Road Starter Box, 12V motor # 10250-1/8 scale Starter Box # 10253-1/8 scale Starter Box w/ Panel Off-Road Starter Box, two 550 motors #

Battery for Starter Box (must have) AA Batteries ( 12 pcs ) for radio RADIO CONTROL UNIT Note: Carefully read the instruction manual of your 2

SUITABLE SERVO SIZE 3 6 mm-41mm 15mm - 21mm 29mm - 42mm Radio must be set at neutral position before installing in the kit.

After installing the battery, connect the battery box. Extend the antenna. (Receiver) Set the trim-lever at center. Turn on the switch.

When the operation stick is in neutral, servo horns must be in neutral as will. *Adjustment can be made by reinstalling the servo horn.

2 REQUIRED FOR OPERATION THINGS NEED BESIDES THE KIT 3.5 cc (21 Class) ENGINE REAR EXHAUST OFNA/Picco P-9R EVO #51219 Glow Plug Long Heat with Battery & Charger # $27.95 (please note OFNA Glow Heats available) Glow Fuel 20% Bottle s with spout # large 500cc # large 500 ccauto Stop # small 250cc # CNC spout 500CC # CNC spout 800CC Note: Pro kit does not include engine! Off-Road Starter Box, 12V motor # /8 scale Starter Box # /8 scale Starter Box w/ Panel Off-Road Starter Box, two 550 motors # /8 scale Starter Box # /8 scale Starter Box,RTR Optional Parts # Power Panel Glow Heater # Cable for Glow Plug 12V Battery for Starter Box (must have) AA Batteries ( 12 pcs ) for radio RADIO CONTROL UNIT Note: Carefully read the instruction manual of your 2 channel radio controller before using. SUITABLE SERVO SIZE 3 6 mm-41mm 15mm - 21mm 29mm - 42mm Radio must be set at neutral position before installing in the kit. SEQUENCE TO SET NEUTRAL Install AA batteries in Radio. Extend the antenna.(transmitter) Install batteries into Car receiver. After installing the battery, connect the battery box. Extend the antenna. (Receiver) Set the trim-lever at center. Turn on the switch. (Transmitter) Turn on the switch. (Receiver) Make sure the servos are in command. When the operation stick is in neutral, servo horns must be in neutral as will. *Adjustment can be made by reinstalling the servo horn. Turn off the switch. (Receiver) 11 Turn off the switch. (Transmitter) 12 Retract the antenna. (Transmitter) 13 More Optional Parts... #10202 NiHm Battery Hump Pack.. $34.95 # NiHm Battery Pack Charger.. $7.95 # OFNA/Picoo Glow Plug.. $4.95 TOOLS NOT INCLUDED IN KIT INCLUDED WITH KIT Instant Cemment Diff. Oil Cutter Phillips Type Screw Drivers ( L ) Curved Scissors Shock Oil 80WT Masking Tape 1.5mm Allen Wrench Phillips Type Screw Drivers ( S ) Precision Caliper 2mm Allen Wrench Needle Nose Pliers Brush Paints 2.5mm Allen Wrench Knife Cross Wrench 4mm'5mm Allen Wrench

3 MUST READ THIS BEFORE RUNNING Running a nitro kit is fun and easy, but to make this a safe and good experience you must observe a few rules. This kit is extremely fast, easily over 40MPH, and can seriously injure someone if you are not careful. Where to run car? Any running area you choose must be dry. Do not run car near any water or wet dirt. Do not run on public streets. It is very easy to have the car run over or damaged by hitting the curb. Do not operate car in tight confined places. The car is very fast and will easily hit something. Do not run near people or animals. The car is very fast and will too easily hit someone. Due noise, you will want to consider the surrounding area when operating the car. Do not operate the car at night. You will not be able to drive it without hitting something. Do not operate the car indoors. Engine exhaust is not healthy. Glow Fuel Glow fuel is poisonous! Glow fuel is flammable! Do not leave in fuel bottle with lid off at any time. Do not use any fuel other than glow fuel in this engine. First Time Starting the Engine Caution! When starting engine make sure the following is observed. Set engine Master needle to 3 turns (rich setting) Do not do this alone, get an experienced friend to help at first. Fill fuel tank, try not to spill fuel. Do not spill fuel on receiver Hold car off the ground, so it will not runaway when first starts Turn on Radio and check the linkage before starting engine. Turn on car receiver battery switch. Always have an air filter on the carburetor to keep dirt out. Engine Break-in See Engine Page. Emergency Stopping Engine When Running Remove air filter and cover carb. intake. Squeeze fuel line and hold until engine stops. With a rag, cover exhaust outlet. Clean oil and dirt from chassis with a degreaser. Precautions This kit is not a toy. Always run car with a second person as a spotter and pitman. Hot Parts - The pipe, manifold, engine and head are very hot and will cause burns. Rotating Parts - Keep hands away from the drive train, wheels, and engine when engine is running. Radio - Check batteries life before running the car. If radio does not have full control of the car with steering and/or throttle/brake do not run until corrected. Failure to correct this will result in possible injury and damage to the car or property. Glow fuel - Do leave the glow fuel unattended with the lid off. Fuel contains Methanol and Nitro Methane and is flammable and poisonous. Store fuel in cool ventilated location. Refer the glow fuel label for additional precautions. Car Fuel tank - Never store fuel in car tank, it will ruin the engine if left in tank. Always turn off the car BEFORE turning off radio. DAMAGE DUE CAR RUN AWAY IS NOT A WARRANTY ISSUE. IF YOU DO NOT BREAK-IN ENGINE CORRECTLY, MAINLY AT LOW RPM, YOU WILL BREAK THE CONNECTING ROD! FAILURE TO NOT READ AND FOLLOW BREAK-IN ENGINE INSTRUCTIONS WILL VOID WARRANTY! Storing Car After Running Remove fuel from tank and fuel lines Turn off radio in car Put a few drops of after run in engine to keep it from rusting.

ASSEMBLY OF THE AIR FILTER Air Filter Sets #10135 - Black $8.95 #10137 - Yellow $8.

Yellow #10028 - Pink #10029 - Blue Air Filter Connector Nylon Strap ( Small ) 3 x 10mm Tapping Screw #10242, Foam Filter oil, $5.

4 ASSEMBLY OF THE AIR FILTER Air Filter Sets # Black $8.95 # Yellow $8.95 Sets includ tube, foam filter pre-filter, oil bottle #10016 Air Filter Sponge Refills Nylon Strap ( Small ) # Black # Yellow # Pink # Blue Air Filter Connector Nylon Strap ( Small ) 3 x 10mm Tapping Screw #10242, Foam Filter oil, $5.95 # Blue # Yellow # Rose Foam Air filters Unit You must oil foam filter before use. Filter will not work if not oiled. Clean with soap and water only. You will damage foam if washed if fuel!

* ADJUSTING THROTTLE LINKAGE BEFORE START THE ENGINE SETTING THROTTLE LINKAGE 1. Turn on your transmitter at first and then the car's electronics (Set the transmitter trim-level in center).

5 * ADJUSTING THROTTLE LINKAGE BEFORE START THE ENGINE SETTING THROTTLE LINKAGE 1. Turn on your transmitter at first and then the car's electronics (Set the transmitter trim-level in center). Adjust the alum. stopper A to made the carburetor in idle position. Adjust the alum. stopper B to leave 2mm space between alum. stopper and brake level. 2. Pull the full throttle trigger. The carburetor should be almost full open. 3. Apply the brake with your transmitter trigger, your carburetor should in idle position. The spring between the alum. stopper and ball end should be compressed. * Align throttle servo same as shown. 1. Insert AA batteries into transmitter (8 Pcs). 2.Turn on transmitter. 3.Turn on receiver. 4.Center throttle trims as shown. A B C 1. Pull Full Throttle. 1. Push trigger to full brake position. 2. Adjust alum. Stopper to increase or decrease the brake. A Brake Idle Position (A) IMPORTANT CHECK RADIO THROTTLE AND STEERING SWITCHES BEFORE RUNNING CAR * Insert into transmitter. Full Throttle (B) Full throttle arm position. Spring rod pulls throttle barrel open and brake rods release pressure on brake cams. B B A C C Full brake arm position. Spring compresses forward and brake rods pull brake levers. Less Brake Optional adjustable linkage shown is OFNA p/n one knob or two knob type. Loose Tighten More Brake * Tighten or loose the adjuster nut will change the brake. Notes: 1) Always check and change radio batteries when low. Running your car with low batteries will greatly shorten the radio range. Loss of radio control will damage your car and is not covered under warranty. 2) Check linkage operation for steering and throttle before starting your car. The directional servo switches on radio may be in the wrong position and must be checked and set for proper operation. 3) Battery problems are the biggest cause of car damage, always check radio operation when running. If you feel the radio is not working correctly, shut down engine immediately and check it out!

6 TROUBLE SHOOTING GUIDE PROBLEM CAUSE SOLUTION Fuel line not primed Fill fuel tank and pressurize tank by capping exhaust ENGINE WILL NOT START Glow plug will not heat(lite) Check glow plug battery heater or replace plug. Engine flooded, too much fuel Check carb. needle setting. Do not over prime. Remove glow plug and poor out fuel. Needle valves not setup Check needle setting for break-in. Servo linkage not correct Check linkage for correct radio neutral. Carb. barrel closed Check for slight barrel gap, 1/6th Fuel tank empty Check fuel level and prime fuel line/carb. Glow plug bad Even if plug heats, change to a known good plug. ENGINE STARTS AND Master needle closed Check master needle setting STOPS Engine is too hot Check needle settings Low end is too lean Check low end needle, factory set. Needle are not correct Check needle settings SLOW THROTTLE Fuel pressure in tank Check pressure line to tank and lid seal. RESPONSE Linkage not opening Check that throttle is fully open at full throttle on radio. Batteries in car are low Turn off engine and replace car batteries. Batteries in car are low Turn off engine and replace car batteries. Radio batteries are low Turn of engine and replace radio batteries. CAR IS HARD TO CONTROL Reception from radio bad Check antenna and batteries. Also, loose screws on OR NO CONTROL AT A chassis can interfere with radio. DISTANCE Car radio is wet Turn off engine and dry radio rec r with air. do not run again until fully dry. Low battery in car Replace batteries before running car. Low servo power Standard servo used in this kit are only 50ioz, up graded servo with 70 or more will work better. STEERING SLOW Battery pack is dead, quickly A rechargable pack is recommended (5 cell 600AE)

8 SPECIAL PARTS LIST FOR HYPER 7TQ BLACK BOOT,SHOCK SHAFT,SILICONE 4PCS BLACK SHOCK TOWER FRONT TQ BLACK BLACK HINGE PIN HOLDER FR LOWER BLK BLACK HINGE PIN HOLDER RR LOWER BLK BLACK SHOCK TOWER REAR TQ BLACK BLACK CENTER TOP PLATE TQ BLACK BLACK SERVO SAVER PLATE TQ BLACK BLACK TORQUE FRONT UPPER PLATE BLACK BLACK RADIO TRAY TQ BLACK SHOCK REPAIR SET 3.5mm SHOCK REPAIR SET 3.5mm SHOCK BODY, FRONT 14mm PAIR SHOCK BODY, REAR 14mm PAIR SHOCK SPRING FR/RR SET 14mm SHOCK PISTON, 14mm 4PCS SHOCK BLADDER 14mm 4PCS SHOCK PLASTIC PARTS 14mm SHOCK PLASTIC PARTS 14mm SHOCK BALL END, STEEL SHOCK SPRINGS 14mm, 28096/ SHOCK FRONT 14mm FOR HYPER SHOCK REAR 14mm FOR HYPER SHOCK SHAFT FR 3.5mm SHOCK SHAFT REAR 3.5mm SPRING, FRONT 14mm BLUE, SOFT SPRING, FRONT 14mm GRAY, MED SPRING, FRONT 14mm WHITE, FIRM SPRING, REAR 14mm BLUE, SOFT SPRING, REAR 14mm GRAY, MEDIUM SPRING, REAR 14mm WHITE, FIRM 8.95

9 HYPER 7 PART NUMBER CROSSOVER Part No.# Crossover (use only OFNA part numbers) OFNA Hyper Description Retail E-1 CLUTCH SHOES, 3 PCS E-9 CLUTCH NUT, PILOT SHAFT E-10 CLUTCH SPRINGS, 3 PCS GEAR, CROWN GEAR, BEVEL SHAFT, DRIVE CASE, DIFF GEAR, SPUR SHAFT, CENTER DRIVE BODY, REAR SHOCK, PAIR SHAFT, REAR SHOCK, PAIR SPRING, REAR SHOCK, BLACK PAIR PLASTIC PARTS, SHOCK SET BODY, FRONT SHOCK, PAIR SHAFT, FRONT SHOCK, PAIR SPRING, FRONT SHOCK, BLACK PAIR PISTON, SHOCKS, 4 PCS BLADDER, SILICONE, SHOCK SET BALL, STEEL 6.8mm 4 PCS REBUILD KIT, SHOCK, SET BOOT, SHOCK SHAFT, SILICONE 4 PCS SHOCKS, REAR SET, PAIR SHOCK, FRONT SET, PAIR DRIVE CUP, CENTER 2 PCS ARM, FRONT TOP PAIR MAIN GEAR BOX L ARM, FRONT BOTTOM PAIR R2L TOWER, FRONT SHOCK CVA JOINTS, PAIR HUB, WHEELS 2 PCS GEAR, PINION PLATE, FRONT HOLDER, FRONT BALL, STEEL, SHOCKS 4 PCS KNUCKLE, STEERING, ALUM. PAIR SHAFT, 4mm SUSPENSION, 4 PCS SHAFT, 3mm SUSPENSION, 6 PCS C-HUB, 17DEGREE, FRONT PAIR UP-RIGHT, REAR PAIR SHAFT, REAR WHEELS PAIR WING SUPPORT, REAR ARM, REAR BOTTOM, PAIR PLATE, REAR TOWER, REAR SHOCK TURNBUCKLES, TOP REAR ARM, PAIR ARM, TOP REAR, PAIR ANTI-ROLL BAR, REAR SHAFT, REAR ARMS WING MOUNTS, REAR BALL, STEEL, REAR MOUNT CENTER DIFF HOUSING, 4 PCS PADS, BRAKE, 4 PCS POSTS, ALUM. CENTER DIFF HOUSING, 4 PCS PLATE, ALUM. CENTER HOUSING MISC. BRAKE SHOE SCREW AND HARDWARE 5.95

10 Part No.# Crossover (use only OFNA part numbers) OFNA Hyper Description Retail DISKS, STEEL, BRAKE CAM, BRAKE, 2 PCS BALL ENDS, STEERING 8 PCS COLLAR, STEEL, STEERING, 6 PCS ARM, SERVO SAVER, 3 PCS POSTS, CENTER DIFF HOUSING, 4 PCS ARM, SERVO SAVER, 3 PCS BUSHING, 6x10mm, SERVO SAVER, 2 PCS SCREWS, M4x15mm, SERVO SAVER, 2 PCS POSTS, ALUM. SERVO SAVER, 2 PCS TORQUE ROD, FRONT AND REAR, 2 PCS BUMPER, FRONT AND REAR SET BODY POSTS CHASSIS MAIN, 3.2mm SHAFT, CENTER SWING, 2 PCS SCREWS, FLAT TAPPING, CHASSIS, 8PC.S SCREWS, M4x8mm 6 PCS. AND M4x10mm 4 PCS MISC. WING SUPPORT HARDWARE TORQUE PLATE, FRONT UPPER TORQUE, ROD-BALL END SET SIDE GUARDS, CHASSIS, GRAY POST, FUEL TANK GUARD, FUEL TANK, GRAY TANK, 125cc SPACER, ENGINE MOUNTS NOT STOCKED MOUNTS, ENGINE, PURPLE, ADJUSTABLE, PAIR MISC. SCREW SET HARDWARE TUNED PIPE MOUNT, PIPE WIRE BATTERY BOX, GRAY RECEIVER BOX, GRAY PLATE, RADIO TRAY, PURPLE POSTS, RADIO TRAY, SET BALL ENDS, SERVO SAVER SET LINKAGE, SERVO SAVER SET MOUNT, TRACK SENSOR SCREWS, SET HX SCREW M5x12mm, 4 PCS THROTTLE LINKAGE SET BRAKE LINKAGE, BALL END TYPE WING AND ALUM. WASHERS BODY AND DECAL SHEET SEE PART NUMBER (GRAY) CAP, SHOCKS, PLASTIC (HYPER & DOM) NUT, WHEELS, PURPLE 4 PCS future DECAL, HYPER 7 SHEETS PB-7 HYPER 7 CHUD TO PBS CONVERSION KIT SIDE GUARDS, CHASSIS, YELLOW WING WITH WASHERS, YELLOW WING WITH WASHERS, LIME WING WITH WASHERS, BLUE WING WITH WASHERS, RED/ORANGE WING WITH WASHERS, BLACK FRONT KING SCREW AND SLEEVE, SET C CAP RING, ALUM. HARD COATED, 4PCS C ENGINE MOUNT CNC ALUM CAP NUT, WHEELS, CNC 17mm, BLACK CAP NUT, WHEELS, CNC 17mm, PURPLE CAP NUT, WHEELS, CNC 17mm, BLUE CAP NUT, WHEELS, CNC 17mm, HARD COAT 11.95

11 Part No.# Crossover (use only OFNA part numbers) OFNA Hyper Description Retail SPEED TRANS, HYPER 7, UNIT L CHASSIS, mm W/DOG BONE(LONG) C-HUB, 22DEGREE, PAIR ARM, 22DEGREE HUB ONLY, PAIR C-HUB, 19DEGREE, PAIR KNUCKLE, STEERING, CNC ALUM. PAIR HOLDER, FRONT, ALUM. BOTTOM HOLDER, FRONT ALUM. TOP HOLDER, REAR ALUM. BOTTOM UP-RIGHT, ALUM. PAIR TORQUE BRACE, FRONT, ALUM. PURPLE (PRO) TORQUE BRACE, REAR, ALUM. PURPLE POSTS, RADIO TRAY AND WING SUPPORT SCREWS AND WASHERS 4mm, PURPLE 4 PCS CHASSIS, mm TURNBUCKLES, SS TOP REAR ARM, PAIR TURNBUCKLES, SS STEERING LINKAGE, 3 PCS SCREWS, ALUM. FOR MAIN GEAR BOX BALL MOUNTS, REAR BOTTOM ARM GRAPHITE SHOCK TOWER, FRONT GRAPHITE SHOCK TOWER, REAR GRAPHITE RADIO TRAY GRAPHITE TRACK SENSOR GRAPHITE DIFF HOUSING PLATE GRAPHITE FRONT UPPER PLATE BATTERY COVER, ALUM SEE PART NUMBER (FRONT) SEE PART NUMBER (CENTER) CVA JOINT, CENTER, PAIR CVA JOINT, REAR ANTI-ROLL BAR, 2.4mm ANTI-ROLL BAR, 2.6mm TURNBUCKLE, FRONT TOP ARM, STEEL, PAIR SPRING SET, MED, PURPLE FLYWHEEL, DUAL BRAKE OPTION, PURPLE FLYWHEEL, DUAL BRAKE OPTION, PURPLE CNC TOWER, FRONT SHOCKS C 7075 CNC TOWER, REAR SHOCKS CNC BRAKE DISC SET S 7075 CNC FRONT PLATE SUPPORT C 7075 CNC REAR PLATE SUPPORT N 7075 CNC ENGINE MOUNT, HYPER CNC CENTER DOG BONES CNC REAR DOG BONES G7-47T GEAR, SPUR, SPIDER DIFF, 47T, HYPER DIFF, SPIDER 8 GEAR DIFF, FRONT or REAR DIFF, SPIDER 8 GEAR DIFF, CENTER G8-48T GEAR, SPUR, SPIDER DIFF, 48T, HYPER UNIVERSAL JOINTS, FRT/REAR 3RINGS UNIVERSAL JOINTS, FRONT PBS T GEAR, SPUR, 47T, HYPER BLACK TUBE, S AIR FILTER, HYPER 7 CHUB & PBS LINKAGE, SPECIAL BALL ROD KITS T CLTUCH BELL, 12T W/BEARING (SHORT) T CLTUCH BELL, 13T W/BEARING (SHORT) T CLTUCH BELL, 14T W/BEARING (SHORT) T CLTUCH BELL, 15T W/BEARING (SHORT) T CLTUCH BELL, 16T W/BEARING (SHORT) T CLTUCH BELL, 17T W/BEARING (SHORT) FUTURE A CNC BALL WITH COLLAR, ANTI-ROLL BAR 4PCS 7.95

12 Part No.# Crossover (use only OFNA part numbers) OFNA Hyper Description Retail A CNC BALLS 6.8mm, 4PCS A CNC BALL WITH COLLAR, STEERING 4PCS A CNC BALL STUD, SHOCK MOUNTS, 4PCS A CNC BALL WITH HEX 8mm, REAR ARM MOUNT, 4PCS A CNC BALL 7.8mm, FRONT ARM TOP 4PCS A CNC BALL WITH BASE 8mm, 4PCS A CNC SERVO SAVER AXLES, 2PCS A CNC BRAKE CAM SET DECAL WINDOWS, HYPER BODIES BODY, HYPER, BLUE BODY, HYPER, YELLOW BODY, HYPER, RED BODY, HYPER, ORANGE BODY, FIRE, WHITE BLUE BODY, FIRE, WHITE PURPLE BODY, FIRE, WHITE BLACK BODY, FIRE, LIME WHITE BODY, FIRE, BLACK WHITE PCR A GEARS, BEVEL, SPIDER DIFF SET C CASE COVER & MISC. PARTS, SPIDER DIFF G GEAR, SPUR, 46T SPIDER DIFF G GEAR, CROWN, 43T SPIDER DIFF S SCREWS, 2.6x21.5 SPIDER DIFF L ARM, FRONT BOTTOM, PAIR R2L U-101MM UNIVERSAL, CENTER, HYPER7 SHORT 101mm PAIR LU-105MM UNIVERSAL, CENTER, HYPER 7 LONG 105mm PAIR MM ANTI-ROLL BAR, 3MM HYPER P DUST SHIELD, PLASTIC, 17DEG CHUB PCR, 7075 CNC PLATE, FRONT LOWER ARM PINS, HYPER PCR, 7075 CNC FRONT SHOCK TOWER, HYPER CHUB PCR, 7075 CNC FRONT SHOCK TOWER, HYPER PBS PCR, 7075 CNC PLATE, STEERING LINK, HYPER PCR, 7075 CNC FRONT TOP PLATE, HYPER CHUB PCR, 7075 CNC FRONT TOP PLATE, HYPER PBS PCR, 7075 CNC FRONT BRACE STIFFENER, HYPER CHUB PCR, 7075 CNC FRONT BRACE STIFFENER, HYPER PBS PCR, 7075 CNC SERVO TRAY, HYPER PCR, 7075 CNC CENTER TOP PLATE, HYPER PCR, 7075 CNC REAR BRACE STIFFENER, HYPER PCR, 7075 CNC REAR STIIFENER MOUNT, HYPER PCR, 7075 CNC REAR SHOCK TOWER, HYPER PCR, 7075 CNC REAR TOE-IN PLATE, 2.O DEGREE (NO LINE) PCR, 7075 CNC REAR TOE-IN PLATE, 2.5 DEGREE (TWO LINE) PCR, 7075 CNC REAR TOE-IN PLATE, 3.O DEGREE (THREE LINE) PCR BRAKE PADS WITH SHOES, PAIR PCR ENGINE MOUNTS, PICCO & N.ROSSI PCR FRONT STEERING SPINDLES, PAIR PCR REAR UP-RIGHTS 0DEG. PAIR PCR REAR UP-RIGHTS 0.5DEG. PAIR PCR LAYDOWN SERVOS CONVERSION KIT HB-TQ-04 YANNICK TQ CONVERSION KIT PCR CLUTCH SHOES, PRE-TRIMED SET CL PCR, 1.O COMP SPRING, BLACK, CLUTCH 3 PCS BLACK FRONT, TOWER, SHOCK, BLACK A CVA AXLES, 8mm, CVA REBUILD, HYPER CVA MISC PARTS, CVA REBUILD, HYPER KINGPIN SCREW AND BUSHING SET, HYPER CHUB S REAR, LOWER ARM, R2 (NEW) BLACK REAR, TOWER, SHOCK, BLACK MANUALS, HYPER 7 RTR & PRO & PBS 7.95

13 BLANK

OWNER S REGISTRATION CARD OFNA Racing congratulates you on your purchase of our fine OFNA Product. With proper maintenance and handling this kit will provide many hours of enjoyment.

14 OWNER S REGISTRATION CARD OFNA Racing congratulates you on your purchase of our fine OFNA Product. With proper maintenance and handling this kit will provide many hours of enjoyment. The registration card should be filled out and mailed to OFNA Racing within 10 days of purchase date. In the event that the kit is incomplete or component parts are broken due to error in manufacturer, contact your dealer from which you purchased the kit for replacement part or call OFNA at (949) for your nearest dealer location. Other items such as radio and engine other covered by individual warranties. IMPORTANT! Please print or type, filling in the information listed below and mail immediately MAIL TO: OFNA RACING 7 VANDERBILT IRVINE, CA TEL: (949) REGISTRATION CARD Write in Your Model Name and Part Number RACER S NAME TEL:( ) ADDRESS CITY STATE ZIP DEALER S NAME TEL: ( ) ADDRESS CITY STATE ZIP OFNA 7 Vanderbilt Irvine, Ca

1:8 SCALE GAS POWERED OFF-ROAD BUGGY

SUPPLEMENTAL MANUAL TQ Sport 1:8 SCALE GAS POWERED OFF-ROAD BUGGY INSTRUCTION MANUAL PLEASE READ INSTRUCTIONS CAREFULLY BEFORE ASSEMBLING THIS MODEL. KEEP THIS MANUAL FOR PARTS NUMBERS WHEN ORDERING. SPECIFICATION