HI PerFORMANCE 1/8 OFF-ROAD NITRO BUGGY. Instruction manual OFNA 7 VANDERBILT, IRVINE, CA PH. (949)

Size: px

Start display at page:

Download "HI PerFORMANCE 1/8 OFF-ROAD NITRO BUGGY. Instruction manual OFNA 7 VANDERBILT, IRVINE, CA PH. (949)"

Cynthia Chase
6 years ago
Views:

1 HI PerFORMANCE 1/8 OFF-ROAD NITRO BUGGY. Instruction manual OFNA 7 VANDERBILT, IRVINE, CA PH. (949)

Do NOT use plugs, like the MC-59 or OS-8 In your box you will find.

2 THINGS NEEDED RTR KITS - REQUIRED FOR OPERATION You will need to buy a few items to start the engine and run the car. Use 20% nitro CAR fuel. Do not use airplane or heli fuels, they will over heat engine. Buy LONG glow plugs, like OFNA/PICCO Plug (#51007 or 51008). Use plugs WITHOUT idle bar. Do NOT use plugs, like the MC-59 or OS-8 In your box you will find.. # Bottle, spout top # Red D size glow heater AA Batteries ( 12 pcs ) You need to get batteries for the radio transmitter and the car receiver packs. Radio TX needs (8) eight AA batteries. Car needs (4) four AA Alkaline., Alkaline type batteries will work, but braking will be reduced and 30 minute life. The best for car, is to use a 5 cell hump receiver pack for increased voltage and longer life.. # Ni-Mh Hump Pack, Recommended Option: You may want to upgrade the car battery pack to a Ni-Cad or Ni-Mh 5 cell type(600ae). This will give more run time. OFNA # Ni-Mh Hump Pack and Ni-Mh Battery Charger # Over-nite Charger TOOLS NOT INCLUDED IN KIT, BUT NEEDED TO MAINTAIN YOUR CAR. Cutter Instant Cement Phillips Type Screw Drivers ( L ) Curved Scissors #91009 $5.95 Grease Phillips Type Screw Drivers ( S ) Cross Wrench #17109 $3.95 Needle Nose Pliers Knife Glow Plug & 17MM Cross Wrench #10801 $6.95

3 MUST READ THIS BEFORE RUNNING Running a nitro kit is fun and easy, but to make this a safe and good experience you must observe a few rules. This kit is extremely fast, easily over 40MPH, and can seriously injure someone if you are not careful. Where to run car? Any running area you choose must be dry. Do not run car near any water or wet dirt. Do not run on public streets. It is very easy to have the car run over or damaged by hitting the curb. Do not operate car in tight confined places. The car is very fast and will easily hit something. Do not run near people or animals. The car is very fast and will too easily hit someone. Due to noise, you will want to consider the surrounding area when operating the car. Do not operate the car at night. You will not be able to drive it without hitting something. Do not operate the car indoors. Engine exhaust is not healthy. Glow Fuel Glow fuel is poisonous! Glow fuel is flammable! Do not leave in fuel bottle with lid off at any time. Do not use any fuel other than glow fuel in this engine. First Time Starting the Engine Caution! When starting engine make sure the following is observed. Set engine Master needle to 3 turns (rich setting) Do not do this alone, get an experienced friend to help at first. Fill fuel tank, try not to spill fuel. Do not spill fuel on receiver Hold car off the ground, so it will not runaway when first starts Turn on Radio and check the linkage before starting engine. Turn on car receiver battery switch. Always have an air filter on the carburetor to keep dirt out of engine. Engine Break-in See Engine Page. Emergency Stopping Engine When Running Remove air filter and cover carb. intake. Squeeze fuel line and hold until engine stops. With a rag, cover exhaust outlet. Storing Car After Running Remove fuel from tank and fuel lines Turn off radio in car Put a few drops of after run in engine to keep it from rusting. Clean oil and dirt from chassis with a degreaser like Simple Green. Precautions This kit is not a toy. Always run car with a second person as a spotter and pitman. Hot Parts - The pipe, manifold, engine and head are very hot and will cause burns. Rotating Parts - Keep hands away from the drive train, wheels, and engine when engine is running. Radio - Check batteries life before running the car. If radio does not have full control of the car with steering and/or throttle/brake do not run until corrected. Failure to correct this will result in possible injury and damage to the car or property. Glow fuel - Do not leave the glow fuel unattended with the lid off. Fuel contains Methanol and Nitro Methane both are flammable and poisonous. Store fuel in cool ventilated location. Refer the glow fuel label for additional precautions. Car Fuel tank - Never store fuel in car tank, it will ruin the engine if left in tank. Always turn off the car BEFORE turning off radio. DAMAGE DUE CAR RUN AWAY IS NOT A WARRANTY ISSUE. IF YOU DO NOT BREAK-IN ENGINE CORRECTLY, MAINLY AT LOW RPM, YOU WILL BREAK THE CONNECTING ROD! FAILURE TO NOT READ AND FOLLOW BREAK-IN ENGINE INSTRUCTIONS WILL VOID WARRANTY! CHECK RADIO SETTING, LINKAGE BEFORE STARTING.

OPTION PART THINGS REQUIRED FOR OPERATION OPTION THINGS NEED BESIDES THE KIT 3.

95 (please note OFNA Glow Heats available) Bottle s with spout # 10160 - large 500cc # 10161 - large 500 ccauto

10250-1/8 scale Starter Box # 10253-1/8 scale Starter Box w/ Panel Off-Road Starter Box, two 550 motors # 10248-1/8

Cable for Glow Plug 12V Battery for Starter Box (must have) AA Batteries ( 12 pcs ) for radio RADIO CONTROL UNIT

SUITABLE SERVO SIZE 36mm-41mm 15mm - 21mm 29mm - 42mm Radio must be set at neutral position before installing in

(transmitter) Install batteries into Car receiver. After installing the battery, connect the battery box.

(Receiver) Make sure the servos are in command.

*Adjustment can be made by reinstalling the servo horn. 11 Turn off the switch. (Receiver) 12 Turn off the switch.

95 # 10214 NiMh Battery Pack Charger.. $7.95 # 51007 or 08 OFNA/Picoo Glow Plug.. $13.

4 OPTION PART THINGS REQUIRED FOR OPERATION OPTION THINGS NEED BESIDES THE KIT 3.5 cc (21 Class) ENGINE REAR EXHAUST OFNA/Picco P7-EVO3 #51216 Glow Plug Heat with Battery & Charger # $$19.95 (please note OFNA Glow Heats available) Bottle s with spout # large 500cc # large 500 ccauto Stop # small 250cc # CNC spout 500CC # CNC spout 800CC Off-Road Starter Box, 12V motor # /8 scale Starter Box # /8 scale Starter Box w/ Panel Off-Road Starter Box, two 550 motors # /8 scale Starter Box # /8 scale Starter Box,RTR Optional Parts # Power Panel Glow Heater # Cable for Glow Plug 12V Battery for Starter Box (must have) AA Batteries ( 12 pcs ) for radio RADIO CONTROL UNIT Note: Carefully read the instruction manual of your 2 channel radio controller before using. SUITABLE SERVO SIZE 36mm-41mm 15mm - 21mm 29mm - 42mm Radio must be set at neutral position before installing in the kit. SEQUENCE TO SET NEUTRAL Install AA batteries in Radio. Extend the antenna.(transmitter) Install batteries into Car receiver. After installing the battery, connect the battery box. Extend the antenna. (Receiver) Set the trim-lever at center. Turn on the switch. (Transmitter) Turn on the switch. (Receiver) Make sure the servos are in command. When the operation stick is in neutral, servo horns must be in neutral as well. *Adjustment can be made by reinstalling the servo horn. 11 Turn off the switch. (Receiver) 12 Turn off the switch. (Transmitter) 13 Retract the antenna. (Transmitter) More Optional Parts... # NimH Battery Hump Pack.. $34.95 # NiMh Battery Pack Charger.. $7.95 # or 08 OFNA/Picoo Glow Plug.. $13.95 TOOLS NOT INCLUDED IN KIT Cutter Instant Cement Phillips Type Screw Drivers ( L ) Curved Scissors Masking Tape INCLUDED WITH KIT 5mm Hex Wrench Phillips Type Screw Drivers ( S ) Brush Cross Wrench #17109 $3.95 Hex Wrench 2.5mm Hex Wrench Needle Nose Pliers Paints 1.5mm Hex Wrench Knife Glow Plug & 17MM Cross Wrench #10801 $6.95 Grease 7mm and 5.5mm Hex Wrench

5 PLASTIC PARTS FOR USE RECEIVER BOX STONE GUARD REAR LOWER ARM REAR UPRIGHT FRONT KNUCKLEARM ARM DIFF. CASE GEAR BOX FRONT LOWER ARM

PLASTIC PARTS FOR USE 40040 CENTER DIFF.

40018 / 40029 CHASSIS BRACE 40031 SERVO SAVER

Do Not Over Tighten Tighten Tighten Ensure

Adhesive Contact Adhesive Scre w Cement Apply

Grease 1:1 True-To-Scale 1:1 ì o ¹Ï Rotate

6 PLASTIC PARTS FOR USE CENTER DIFF. MOUNT WING STAY FRONT UPPER ARM / CHASSIS BRACE SERVO SAVER WING SYMBOL USED THROUGHOUT THE INSTRUCTION MANUAL BAG Parts Bag Used Degrease With Motor Spray Do Not Over Tighten Do Not Over Tighten Tighten Tighten Ensure Free Movement Ensure Free Movement Contact Adhesive Contact Adhesive Scre w Cement Apply Screw Cement Oil Apply Oil Apply Grease Apply Grease 1:1 True-To-Scale 1:1 ì o ¹Ï Rotate Direction Clockwise Rotation Rotate Direction Anti-clockwise Rotation

1 ASSEMBLY OF THE FRONT AND REAR DIFF. Builds two differentials for front and rear.

8mm Pin 40006 Oil 40513 40009 49032 Oil 40003 40006 8x16mm Ball Bearing 40009 40513 2 ASSEMBLY OF

Step 1 30776 Step 2 40513 30773 Tighten Tight the diff screws in this order. 30776 4x10mm Washer.

Oil #3000 for front and the #1000 for rear *Fill the Diff. case to approx. 80% with the Diff.

7 1 ASSEMBLY OF THE FRONT AND REAR DIFF. Builds two differentials for front and rear x4mm Set Screw 4x4 mm P6 O-Ring x13.8mm Pin Oil Oil x16mm Ball Bearing ASSEMBLY OF THE FRONT AND REAR DIFF. Builds two differentials for front and rear. Step Step Tighten Tight the diff screws in this order x10mm Washer...X X8 Flat Head mm Cross Pin...X4 Diff. Oil *Put the Diff. Oil #3000 for front and the #1000 for rear *Fill the Diff. case to approx. 80% with the Diff. Oil 3 ASSEMBLY OF THE CENTER DIFF x4mm Set Screw 4x4mm P6 O-Ring X13.8MM PIN Oil Oil 8x16mm Ball Bearing

Oil Use 5000 weight diff. oil in the center. Fill the Diff.

5 ASSEMBLY OF THE FRONT GEAR CASE Scre w Ce me nt 5x4mm Step 1

30080 4x45mm 40024 40017 8x16mm Ball Bearing 49048 40015

8 4 ASSEMBLY OF THE CENTER DIFF x10mm Washer Tighten Tight the diff screws in this order Flat Head mm Cross Pin...X2 4 2 Diff. Oil Use 5000 weight diff. oil in the center. Fill the Diff. Case to approx. 80% with the Diff.Oil. 5 ASSEMBLY OF THE FRONT GEAR CASE Scre w Ce me nt 5x4mm Step x4mm Set Screw x16x0.2mm Shim 4x16mm Flat Head Screw...X x16mm 4x16mm Apply Grease Step x45mm x16mm Ball Bearing x16mm x45mm 4x16mm 6 ASSEMBLY OF THE FRONT SHOCK STAY mm Nylon Nut mm Nylon Nut mm Nylon Nut x12mm x16mm x16mm 4x12mm x28mm Cap Screw 2

7 ASSEMBLY OF THE FRONT LOWER ARMS Assembly for both right and left side.

Assembly for both right and left side. 2.5mm 90020 2.5mm E-Ring 2.

side. 94034 4x4mm Set Screw Step 1 * L for left handside. 36903 36905 L 36055 2.5x16.

9 7 ASSEMBLY OF THE FRONT LOWER ARMS Assembly for both right and left side E-Ring x10mm Set Screw 4x10mm ASSEMBLY OF THE FRONT UPPER ARMS Assembly for both right and left side. 2.5mm mm E-Ring 2.5mm ASSEMBLY OF THE KNUCKLE ARMS Assembly for both right and left side x4mm Set Screw Step 1 * L for left handside L x16.8mm Pin Ensure Free Movement Step 2 8x16mm Ball Bearing Do Not Over Thigten mm Steering Ball Screw Cement x4mm 3

10 ASSEMBLY OF THE FRONT SUSPENSION ARMS

10 10 ASSEMBLY OF THE FRONT SUSPENSION ARMS Assembly for both right and left side. * Insert the drive shaft before assembling the knuckle arm. 11 ASSEMBLY OF THE FRONT STABILIZER Assembly for both right and left side x8mm Set Screw mm Ball Makes two rods for left and right hand-side x16mm x8mm x16mm 12 ASSEMBLY OF THE FRONT STABILIZER 3x Screw Cement x Set Screw Screw Cem ent 3x 8mm Flat Head x x Ensure Free Movement 4

11 13 ASSEMBLY OF THE SERVO SAVER Plastic Flange Bushing ASSEMBLY OF THE SERVO SAVER AND THE STEERING TIE-ROD cr w S e me t Ce n Nylon Nut 4x10mm Screw Cement x10mm x18mm x18mm Flat Head :1 *Approx. 26mm ASSEMBLY OF THE SERVO SAVER ONTO THE FRONT GEAR BOX ½w½Ä²Õ»P«e¾ ½ü½c²Õ X Nylon Nut x10mm 4x10mm 3x20mm x20mm Flat Head 3x20mm

16 ASSEMBLY OF THE REAR GEAR CASE Screw Cement Step 1 5x4mm Step

4x12mm 8x16mm Ball Bearing 49012 49049 40024 13x16x0.

Step 2 94003 40027 41009 41010 94004 90018 3x25mm Cap Screw 41010

12 16 ASSEMBLY OF THE REAR GEAR CASE Screw Cement Step 1 5x4mm Step 2 4x12mm x4mm Set Screw x12mm x12mm 8x16mm Ball Bearing x16x0.2mm Shim x16mm x45mm x16mm x45mm Flat Head Screw...X2 4x45mm ASSEMBLY OF THE REAR SHOCK STAY Step Step x25mm Cap Screw ASSEMBLY OF THE WING STAY x20mm x16mm x20mm 3x16mm x20mm x16mm 6

13 19 ASSEMBLY OF THE WING STAY Nylon Nut 4x20mm mm Nylon Nut 4x16mm x16mm x20mm 4x16mm 4mm Nylon Nut 3x25mm x25mm 20 ASSEMBLY OF THE REAR LOWER ARMS Assembly for both right and left side mm E-Ring x4mm Set Screw mm x16.8mm Pin mm 5x4mm ASSEMBLY OF THE REAR SUSPENSION ARMS Assembly for both right and left side E-Ring x10mm Set Screw 4x10mm Ensure Free Movement

14 22 ASSEMBLY OF THE REAR SUSPENSION ARMS Nylon Nut Nylon Nut Assembly for both right and left side. Assembly of the rear upper arm mm Ball x18mm x25mm 3x18mm Nylon Nut 1:1 *Approx x25mm *Insert the drive shaft before assembly the upper arms. 23 ASSEMBLY OF THE REAR STABILIZER Assembly for both right and left side. Makes two rods for left and right hand-side x8mm Set Screw mm Ball x8mm x16mm 3x16mm 24 ASSEMBLY OF THE REAR STABILIZER 3x Scre w Cement x Set Screw Scre w Ce me nt 3x Flat Head Screw x Ensure Free Movement 8

15 25 ASSEMBLY OF THE CENTER DIFF. MOUNT Step 1 Step 2 Step ASSEMBLY OF THE BRAKE DISK INTO CENTER DIFF. MOUNT Step 1 A B C Step Step 2 C * Place the brake disc between the brake disc pads. * Remove the double-side tape before assembly. A B Brake disc double-side tape ASSEMBLY OF THE CENTER DIFF. MOUNT *Approx. 8mm *8m ù Step 1 Approx. 4mm Step x x Set Screw x Plastic Flange Bushing

28 31 ASSEMBL Y OF THE STONE GUARD Assembly for both right and left side.

..x6 40046 40046 29 ASSEMBLY OF THE FRONT GEAR CASE ONTO CHASSIS 94039 4x10mm

16 28 31 ASSEMBL Y OF THE STONE GUARD Assembly for both right and left side x ASSEMBLY OF THE FRONT GEAR CASE ONTO CHASSIS x10mm Flat Head x12mm Flat Head x16mm Flat Head 4x10mm 4x12mm 4x16mm 30 ASSEMBLY OF THE CENTER DIFF. ONTO CHASSIS *Insert the drive shaft into the cap joint before assembly the center diff. onto chassis x10mm Tapping Screw x10mm Flat Head Screw 2.6x10mm 2.6x10mm 4x10mm 4x10mm 10

17 31 ASSEMBLY OF THE REAR GEAR CASE ONTO CHASSIS x12mm Flat Head *Insert the drive shaft into the cap joint before assembly rear gear box onto chassis x16mm Flat Head 4x16mm 4x12mm 32 ASSEMBLY OF THE RADIO TRAY Step 1 3x8mm Step x8mm Washer...x8 3x8mm x6 3x8mm 3x8mm x ASSEMBLY OF THE RADIO TRAY AND RECEIVER BOX 2x10mm Tapping Screw x10mm * Use the screw provided with your switch x25mm Receiver 2x25mm Screw Switch

18 34 ASSEMBLY OF THE STEERING SERVO AND STEERING ROD 1:1 *Approx. 18.5mm mm Ball * Use the screw provided with your servo ASSEMBLY OF THE RADIO TRAY AND STICK PACK BATTERY Battery Case ASSEMBLY OF THE RADIO TRAY ONTO CHASSIS Nut Flat Head...x

37 ASSEMBLY OF THE FUEL TANK ONTO CHASSIS Flat Head

THE CLUTCH 10010 10040 38313 10098 Screw Cem en t *Fit

and bend the small end in the clutch spring behind the

39 ASSEMBLY OF THE CLUTCH AND ENGINE MOUNT 3x16mm

19 37 ASSEMBLY OF THE FUEL TANK ONTO CHASSIS Flat Head Do Not Over Tighten ASSEMBLY OF THE CLUTCH Screw Cem en t *Fit the flywheel using a pair of the plier and cross wrench *Place the clutch shoes with the clutch springs over the 3 pins of the flywheel. *Using a phillips screw driver or needle nose pliers and bend the small end in the clutch spring behind the pilot shaft than press down. 39 ASSEMBLY OF THE CLUTCH AND ENGINE MOUNT 3x16mm 3x16mm 3x8mm Washer x10x4mm Ball Bearing 5x9x0. Washer Nylon Nut x9x0. 3x5mm Cap Screw 3x8mm x16mm Cap Screw 3x5mm

40 ASSEMBLY OF THE ENGINE ONTO CHASSIS Note book Paper.

backlash between spur gear and clutch bell gear, applying

*If the space is not correct the spur gear will be damaged.

Screw 49055 10060 94039 4x10mm Flat Head 10185 ZIP TIES 31990

THROTTLE LINKAGE 94033 3x Set Screw 2mm Nut.

3x 10300 30802 30172 30531 3x 10300 30802 2x7mm Washer 2x4mm.

20 40 ASSEMBLY OF THE ENGINE ONTO CHASSIS Note book Paper mm Engine Mount Screw *Use note book paper to set gear backlash between spur gear and clutch bell gear, applying pressure while retightening the engine. *If the space is not correct the spur gear will be damaged ASSEMBLY OF THE MANIFOLD AND MUFFLER x4mm Set Screw x10mm Flat Head ZIP TIES x10mm 4x4mm x4mm 42 ASSEMBLY OF THE THROTTLE LINKAGE x Set Screw 2mm Nut...x Step 1 2x7mm x4mm x25mm Step 3 3x x x7mm Washer 2x4mm...X x x7mm x4mm Step 2 2x8mm Step 4 Ensure Free Movement 2x8mm Cut off the servo saver as shown mm 14

43 ASSEMBLY OF THE THROTTLE LINKAGES INTO LEVER 3x 94033 3x Set Screw 10300

10769 44 ADJUSTING THE ENGINE CONTROL LINKAGES (Neutral) (Throttle High)

1mm gap Turn on the Transmitter then Receiver and set the Engine Control Servo

Adjust the idling adjusting screw on the Carburetor to be open approx. 1mm gap.

Adjust the Engine while it is not running.

not opening fully or if it is opening excessively.

21 43 ASSEMBLY OF THE THROTTLE LINKAGES INTO LEVER 3x x Set Screw mm Fuel Tube Snap On * Use the screw provided with your servo ADJUSTING THE ENGINE CONTROL LINKAGES (Neutral) (Throttle High) (Brake) Approx. 0.5mm Idling adjusting Screw Approx. 1mm gap Turn on the Transmitter then Receiver and set the Engine Control Servo Trim to the neutral position. Adjust the idling adjusting screw on the Carburetor to be open approx. 1mm gap. Adjust both of the Engine Control and Brake linkage accordingly. Adjust the Engine while it is not running. Carburetor is Opening fully Adjust the Servo-Horn mounting position for the Carburetor to be full open. Change the pivot mounting position on the servo horn in case the Carburetor is not opening fully or if it is opening excessively. Or if available on the Transmitter, adjust the Throttle high end point. Adjust so the brakes work smoothly. If the brakes apply too much or not enough, adjust accordingly. Or if available on the Transmitter, adjust the High-End Brake adjustment. Adjust to Change the front or Rear Brake.. 45 ASSEMBLY OF THE AIR FILTER x8mm 3x8mm *Apply filter oil to the foam before use *Apply filter oil to the foam before use. ZIP TIES

37.5mm 28mm 46 ASSEMBLY OF THE FRONT SHOCKS *Assemble 2 for front CORRECT SHOCK ASSEMBLY 41012 1mm Washer 41012 3.

6x5mm 40054 Carefully screw the shock shaft into the bottom of the plastic ball and until the distance between the ballend and the

41003 41012 2mm Washer Step 3 Step 4 Fill the shocks with oil.

To remove air bubbles by slowly moving piston up and down. 3.

47 ASSEMBLY OF THE REAR SHOCKS *Assemble 2 sets for rear 41012 1mm Washer 41012 3.

shock body is 37.5mm for the rear. N.B. Do not over tighten as the plastic will strip.

22 37.5mm 28mm 46 ASSEMBLY OF THE FRONT SHOCKS *Assemble 2 for front CORRECT SHOCK ASSEMBLY mm Washer mm O-Ring Fit the o-ring into groove before assembly x5mm x5mm Carefully screw the shock shaft into the bottom of the plastic ball and until the distance between the ballend and the shock body is 28mm for the front. N.B. Do not over tighten as the plastic will strip mm Washer Step 3 Step 4 Fill the shocks with oil Step mm Ball mmx1mm O-Ring Pull down piston and pour oil into shock cylinder. 2.To remove air bubbles by slowly moving piston up and down. 3.Pull down piston, attachpressure top and shock oil overflow with tissue paper *Cut 7mm for front. 47 ASSEMBLY OF THE REAR SHOCKS *Assemble 2 sets for rear mm Washer mm O-Ring Fit the o-ring into groove before assembly x5mm x5mm Carefully screw the shock shaft into the bottom of the plastic ball and until the distance between the ballend and the shock body is 37.5mm for the rear. N.B. Do not over tighten as the plastic will strip mm Washer Step 3 Step 4 Fill the shocks with oil Step mm Ball mmx1mm O-Ring Pull down piston and pour oil into shock cylinder. 2.To remove air bubbles by slowly moving piston up and down. 3.Pull down piston, attachpressure top and shock oil overflow with tissue paper

23 48 ASSEMBLY OF THE FRONT SHOCK ABSORBER Nylon Nut x8mm Washer x20mm 3x8mm 3x20mm Assembly for both right and left side. 49 ASSEMBLY OF THE REAR SHOCK ABSORBER Nylon Nut x8mm Washer x20mm 3x8mm 3x20mm Assembly for both right and left side. 50 ASSEMBLY OF THE FUEL TUBE Connect to carbulater. Connect to pressure nipple. Connect to fuel nipple Connect to fuel t ank nipple

24 51 ASSEMBLY OF THE WING Nylon Nut Body Reamer (Not included) Drill two 7mm holes for mounting. 52 ASSEMBLY OF THE TIRES AND WHEELS Apply instant glue into the groove of the wheel INSTANT GLUE ASSEMBLY OF THE TIRE ONTO FRONT KNUCKLE AND REAR HUB Assembly for both right and left side Wheel Nut Tire and Wheel assembly

25 54 ASSEMBLY OF THE BODY AND PAINTING Cut out the body as shown. Use a neutral detergent to remove any dirt and oil. Mask the windows from the inside with masking tape. Apply internal color decals from the inside and paint the body with polycarbonate spray paints. Spray Paint Cutting holes. *Make a 8mm hole for body mount.* *Make a 8mm hole for body mount. Cut out for engine. *Hole for engine. *Hole for fuel tank. *Hole for antenna pipe. *For the exhaust outlet of the muffler. 19

55 MOUNTING BODY 31159 Body Clips 31159 Body Clips 56 STARTING OF THE ENGINE How to start the engine: 1.

Start engine with 12V starter. ( Note the direction of the starter.) 5. After the engine be started, remove the 1.2V glow plug starter.

) Glow Plug (Not Included) Normal Plug 1.2V Glow Plug Igniter (Not Included) 1.

12V Starter There is 2 types of glow plug available "NORMAL or Turbo" depending of the type of the engine.

26 55 MOUNTING BODY Body Clips Body Clips 56 STARTING OF THE ENGINE How to start the engine: 1. Turn on transmitter and then receiver. 2. Fill fuel tank with fuel bottle. 3. Connect 1.2V glow plug starter. 4. Start engine with 12V starter. ( Note the direction of the starter.) 5. After the engine be started, remove the 1.2V glow plug starter. 12V Starter and Starter Ring ( Not Included) Starter rubber ring for car. ( Insert starter rubber ring on the 12V starter.) Glow Plug (Not Included) Normal Plug 1.2V Glow Plug Igniter (Not Included) 1.2V Glow Plug Igniter Turbo Plug * Follow the engine manufacturer instruction manuals regarding engine set-up, carburetor and maintenance. 12V Starter There is 2 types of glow plug available "NORMAL or Turbo" depending of the type of the engine. *To start the car, attach a glow plug igniter to the glow plug, and use either an electric starter or starter box applied to the flywheel exposed through the chassis. 1.2V Glow Plug Igniter 1.2V 1.2V 1.2V Glow Plug Igniter Note the direction of the starter. Connect with 12V battery. Starter Box (Not Included) 20

27 34952 Picco off-road parts list OFNA DESCRIPTION RETAIL OFNA DESCRIPTION RETAIL CLUCTH SHOES BLACK 3PCS DOG BONES, 93MM PAIR LX PIN FLYWHEEL,.21 CORN TYPE BALL ENDS, PLASTIC, ANTI-ROLL MANIFOLD, ROUND EXHT, BLACK SERVO SAVER HORN SEALS.21, RED ROUND PORT, 2PC PLATE, SERVO SAVER,SLIDER H.C CLUTCH NUT, SG SHAFT SPRING, SERVO SAVER SPRINGS,CLUTCH,GOLD 1.1M 3PCS ALUM. RING, SERVO SAVER ADJ.RI FLAT HEAD ENGINE MOUNT SCREWS AXLE TUBE, SERVO SAVER SPRING, MANIFOLD, R.PORT AXLE POSTS, SERVO SAVER FUEL LINE 3FT. GRAY/BLACK SCREWS, SERVO PLATE SILICONE JOINT TUBE BLACK BALLS, 7MM 4PCS CLIPS, FUEL LINE, BLK CONE, ALUM. 3MM, 4PCS SWITCH COVER, SILICONE BLACK CENTER DIFF MOUNT ALUM. STOPPER KIT, 6 PCS BRAKE DISCS, STEEL 4PCS CLUTCH BELL W/BEARINGS, 13T CENTER, STEEL DIFF POSTS, 4PCS HI FORCE WING, 1/8 WHITE SPRING, BRAKE SEPARATORS, 8PCS JOINT CAP, 6mm, 2 PCS SCREWS, BRAKE PADS, 4PCS LEVER, BRAKE STONE GUARDS, 9.5 CHASSIS,BLK RODS, BRAKES, 2 PCS BOX, RECEIVER AND BATTERY BRAKE CAM POST, PIPE HOLDER BALL END WITH COLLAR, 6mm WIRE, PIPE MOUNT, L-SHAPE TURNBUCKLE 3x30mm PICCO SHAFTS,3.5m FRONT SHOCKS, 2PCS STEERING ENDS, PLASTIC 6 PCS SHAFTS,3.5m REAR SHOCKS, 2PCS mm BALL, STEEL (NO COLLAR) COVERS, SHOCK SHAFTS, SILICONE ENGINE MOUNT KIT SEALS, 14.7mm O-RING, 4PCS SPRING, THROTTLE LINKAGE NYLOK NUT, 2.5, PISTON NUT, ANT TUBE AND MOUNT CHASSIS, 9.5 HARD COATED WHEEL HUB, LX1, PICCO 9.5 H.C BALL ENDS, PLASTIC, REAR UPPER SERVO HORN HEAVY DUTY BLACK TANK, 9.5 FUEL 150cc TANK CROSS PIN AXLES, 4mm STEEL ARMS, FRONT UPPER 9.5 MBX PR WASHER, 4x10x0.2mm 4PCS O-RING P-10 FOR X1-CR,9.5 SHCK LINKAGE, 2 THROTTLE LINKAGE AIR FILTER SET, X BODY CLIPS, CHROME FOAM, REPLACEMENT FOR PIPE, 1:8 TUNED, BLACK CONNECTOR, RUBBER FOR FRONT UNIVERSALS, PR. COMP PLASTIC BATTERY CASE FOR RTR BEARING, 5x10, 2 PCS ARMS, LOWER,FRNT&RR 95 MBX BEARING, 8x16mm, PAIR CENTER DIFF. MOUNT POST PIN, 2.5x17mm, HEX HUBS, 4PCS DIFF. GEAR (small & large)alum REAR UP-RIGHT (8mm BEARING) PR FRONT or REAR ARM SHAFT 4x REAR AXLES, 8mm PAIR WHEEL NUT 5mm REAR BONES, 91mm 2PCS. 95MBX PLASTIC SHOCK PARTS,13/16mm KNOB, BRAKE ADJUSTER, 2PCS SHOCK BIG BORE FRONT 16MM PAIR ARM PINS, 4PCS LX SHOCK BIG BORE REAR 16MM PAIR BRAKE PAD, 4PCS SHOCK BODY FRONT 16MM PAIR BRAKE PAD WASHER, 4PCS SHOCK BODY REAR 16MM PAIR STEERING BALL END, 7mm, 8PCS SHOCK CAP 16MM 4PCS x46MMTURNBUCKLES,4PCS SHOCK SPRING ADJ. 16MM 4PCS mm BALL, 6 PCS O-RING 19x1.5MM 16MM 4PCS x40mm TURNBUCKLES, 2 PCS BLK PLASTIC SHOCK PARTS 16MM SET KNUCKLE, PIVOT BALL (mbx4) 2PC CAP SCREWS 3X28MM 4PCS PIVOT BALLS, STEEL (mbx4) 4PCS SHOCK BALL END POST LONG 4PCS mm ALUM. NUT (mbx4) 4 PCS SHOCK PISTON 16MM 8PCS WASHER PLASTIC, 14mm NUTS REPAIR KIT FOR 16MM SHOCK BODY CLIPS, 10 PCS. SMALL PRESSURE TOP ORANGE 16MM 4PCS CONE, TAPERED 7mm, SG SPRING 16MM SUPER SOFT YEL SET GEAR, SPUR, 47T STEEL SPRING 16MM SOFT WHITE SET CASE, DIFF, 1 PC GEAR, 13T PINION CAP JOINT, BRAKE, 2PCS GEAR, BEVEL, 43 TOOTH CAP JOINT, FNT&RR DIFF, 2PCS TOWER, FRONT PICCO 9.5 BLACK SEAL, P-6 O-RING, DIFF, 2PCS ARM HOLDER, FR LOWER BLACK PIN, 2.5X13.8MM, DIFF, 2PCS ARM HOLDER, RR LOWER BLACK GASKET, DIFF 3PCS SHOCK TOWER, REAR 4mm BLACK BUMPER, FRONT PLATE, TOP FR SUPPORT ALUM BLK FRONT HOLDER, LOWER ARMS 5PCS PLATE, SERVO SAVER SLIDER BLK FRONT UPPER ARMS, 1PC PLATE, TOP CENTER DIFF BLACK MAIN GEAR BOX, FRONT&REAR, 1PC RADIO TRAY ALUM. BLACK BRACE, CENTER, NYLON, 9.5 KIT SPRING AND MANIFOLD FLANGE ANTI-ROLL KIT (FRONT/REAR) BODY, PRINTED PICCO OFF-ROAD ARMS, FRONT&REAR, LOWER PAIR FOAM DONUTS, GRAY SET SHIM, 13X16XO.2MM, DIFF GEAR, mm TrueLITES DISH, WHT 6PACK WING MOUNT SUPPORT SET TIRES, BONES (46)w/FOAM, PAIR 19.95

SETTING GUIDE FRONT CAMBER ANGLE SETTING REAR CAMBER ANGLE SETTING + - - + + - - + Positive Negative Positive Negative

Raise the chassis to it's maximum clearance before the wheels leave the ground.

The camber angle adjustment can be moving the turnbuckle rod on the upper arms, clockwise or anti-clockwise.

5mm hex wrench to adjust upper arm ball in front.

Rod Soft 12 Firm Firm front suspension, less steering. Soft front suspension, more steering.

30 SETTING GUIDE FRONT CAMBER ANGLE SETTING REAR CAMBER ANGLE SETTING Positive Negative Positive Negative Turnbuckle Place the model car on flat surface. Raise the chassis to it's maximum clearance before the wheels leave the ground. Adjust the length of the front and rear upper arms so that the wheels are right angle to the ground. The camber angle adjustment can be moving the turnbuckle rod on the upper arms, clockwise or anti-clockwise. (We suggest use zero degree for the front and 1.5 negative degree for the rear.) *Use 2.5mm hex wrench to adjust upper arm ball in front. FRONT TOE-IN AND TOE-OUT SETTING FRONT SHOCK ANGLE SETTING NEUTRAL POSITION TOE-OUT TOE-IN TOE-OUT Soft Firm Steering Rod Soft 12 Firm Firm front suspension, less steering. Soft front suspension, more steering. REAR SHOCK ANGLE SETTING Soft Firm Adjust the length of front steering rod to change thetoe angle. Making the tie rod longer will make the front tires become toe-in. Response will be slower and will over steer. Making the tie rod shorter will make the front tires become toe-out. Response will be quicker and will under steer. Firm rear suspension, over steering. Soft rear suspension, under steering. Soft 123 Firm

OWNER S REGISTRATION CARD OFNA Racing congratulates you on your purchase of our fine OFNA Product. With proper maintenance and handling this kit will provide many hours of enjoyment.

31 OWNER S REGISTRATION CARD OFNA Racing congratulates you on your purchase of our fine OFNA Product. With proper maintenance and handling this kit will provide many hours of enjoyment. The registration card should be filled out and mailed to OFNA Racing within 10 days of purchase date. In the event that the kit is incomplete or component parts are broken due to error in manufacturer, contact your dealer from which you purchased the kit for replacement part or call OFNA at (949) for your nearest dealer location. Other items such as radio and engine other covered by individual warranties. IMPORTANT! Please print or type, filling in the information listed below and mail immediately MAIL TO: OFNA RACING 7 VANDERBILT IRVINE, CA TEL: (949) REGISTRATION CARD Write in Your Model Name and Part Number RACER S NAME TEL:( ) ADDRESS CITY STATE ZIP DEALER S NAME TEL: ( ) ADDRESS CITY STATE ZIP OFNA 7 Vanderbilt Irvine, Ca

RTR Instruction Manual

OFNA Racing 22692 Granite Way, Ste. B Laguna Hills, Ca. 92653 (949) 586-2910 Www.ofna.com RTR Instruction Manual PURE COMPETITION... PRE-ASSEMBLED ASSEMBLED CHASSIS WITH RADIO AND ENGINE REQUIRED FOR OPERATION