New Generation Rear Wheel Drive

Size: px

Start display at page:

Download "New Generation Rear Wheel Drive"

Claud Ira Paul
6 years ago
Views:

1 New Generation Rear Wheel Drive ABC HOBBY ORIGINAL RADIO CONTROL CAR Instruction Manual Study the instructions thoroughly before assembly. REAR 2 WHEEL DRIVE REAR MOUNTED MOTOR BELT DRIVE DOUBLE DECK CHASSIS BALL DIFFERENTIAL FULL ADJUSTABLE SUSPENSION WHEEL BASE 210mm BODY WIDTH 157mm-163mm ROAD CLEARANCE 4-10mm

2 DIFFERENTIAL + Philip Driver Diff Pulley Flange Cap Screw Diff Ball Nylon Nut Thrust Washer Thrust Ball 850 Bearing Diff Joint Cup A 850 Bearing Diff Ring Allen Wrench **Don t tighten too much it Hold Pulley. Diff Spring Nylon Nut Diff Ring Diff Ball Ball Diff Pulley (35) 850 Bearing Diff Ring Diff Spring Thrust Washer Thrust Ball Thrust Washer Cap Screw Then, Diff Joint Cup B turns to the left. Repeat so that demister moves smoothly. Turn Diff Joint Cup A to Right Diff Joint Cup B Pulley Tensioner - Flat Driver 1510 Bearing When Put Diff Joint Ring, Use Pliers. Diff Joint Ring 1510 Bearing Diff Joint Ring - Flat Driver HOLD A and B, then turn the diff gear. The gear must not turn easily Ball Stud 4mm Steering Shaft 3mm E Clip Nylon Nut (2.5mm) Nylon Nut (3mm) STEERING COMPONENT Ball Stud 4mm Steering Bridge Plastic Bearing 3x6F Nylon Nut (3mm) Nylon Nut (2.5mm) RIGHT Steering Shaft Nut (3mm) Steering Post Plastic Bearing 4x8 Steering Wiper Right Plastic Bearing 4x8 3mm E Clip Steering Nut Ball Stud 4mm Steering Arm LEFT Steering Wiper Left Steering Pipe Nut (3mm) Steering Shaft Spacer!! Direction!! Fit Hex Shape Don't over tighten the nylon Nuts. Rack must move smoothly without bind. Smooth 1

3 3X10mm Flat STEERING / ROWER ARM Steering Unit Suspension Arm Holder A Hex Cap Screw 3x8mm Button Suspension Arm Holder B 3X10mm Flat Mail Chassis 3X10mm Flat Lower Arm Shaft *You can adjust suspension feeling by Skid Plate. You got more effect at bumpy surface such a parking lot. STR Ball Stud Base 3x8mm Button Lower Arm Shaft STR Lower Suspension Arm Sus. Arm Pin Ball Sus. Arm Pin Ball Lower Suspension Arm Lower Arm Shaft Hex Cap Screw Skid Plate Sus. Arm Pin Ball Sus. Arm Pin Ball Suspension Arm Holder D Hex Cap Screw Skid Plate Suspension Arm Holder A 3X10mm Flat Bumper 3X10mm Flat Lower Suspension Arm (Front) STR Lower Suspension Arm (Rear) Smooth Smooth Smooth Smooth **All Suspension Arms must move smoothly without slack. 2

4 2.6X5mm Binding Screw 3x8mm Binding Screw 3x10mm Binding Screw 3X8mm Flat 3x3mm Set Screw (For Anti-Roll Bar) Ball Stud 6mm BULKHEAD / SHOCK TOWER Front Suspension Arm 2.6X5mm Binding Screw 3x8mm Binding Screw Front Shock Tower 3x3mm Set Screw (For Anti-Roll Bar) 2.6X5mm Binding Screw Upper Suspension Pin (3mm x 24mm) Front Bulkhead Upper Suspension Holder Front Ball Stud 5.8x11mm Upper Suspension Pin (3mm x 24mm) Suspension Arm (Front) Ball Stud 6mm 3X8mm Flat 3x8mm Binding Screw Anti-Roll Bar Holder 3x8mm Binding Screw 3x10mm Binding Screw Front Bulkhead 3x8mm Binding Screw Rear Shock Tower Rear Upper Bulkead 3x3mm Set Screw (For Anti-Roll Bar) Rear Suspension Arm (Rear) Ball Stud 6mm 3x8mm Binding Screw 3X8mm Flat Ball Stud 5.8x11mm Rear Shock Tower 3x6mm Binding Screw CENTER GEAR UNIT 3x6mm Binding Screw Spur Gear 84T 2X7.8mm Pin P8 O Ring 4 mm E Clip 2X7.8mm Pin Spur Gear Holder 2X7.8mm Pin P8 O Ring **Install P8 O Ring in slot of Spur Gear Holder for prevention of falling off of 2X7.8mm Pin. 4 mm E Clip Center Gear Unit 3

5 REAR BULKHEAD 3X10mm Button 3X10mm Button Rear Shock Tower 3X10mm Button 3X40mm Flat 3X10mm Button Nylon Nut (3mm) Spur Gear Rear Bulkhead 3X40mm Flat Drive Belt Bulkhead Spacer Loose Push the Drive Belt. Best Slackness is 2-3mm. If Belt tension is tight, make a drag, If loose, gear will be skip. Ball Diff Pulley Motor Holder Standard (Center) Bulkhead Spacer **Through in the Drive Belt Nylon Nut (3mm) Tight Rear Lower Bulkhead **Use same slot for right and left. MAIN CHASSIS 3X10mm Flat Flat Head Screw Rear Bulkhead Front Bulkhead 3X10mm Flat 3X10mm Flat 4

6 Steering Ball Steering Ball Washer Front KNUCKLE ARM/REAR UPRIGHT Knuckle Arm Steering Ball Rear Rear Upright Steering Ball Smooth 7mm Ball Nut Steering Ball Washer 7mm Ball Nut Steering Ball Washer 1510 Bearing Steering Ball Washer 7mm Ball Nut **See Direction of Steering Ball Washer Tighten 7mm Ball Nut in 4mm Allen Wrench. Dog Bone Smooth 1150 Bearing Front Axle Shaft Axle Shaft Wheel Hub Spacer Wheel Hub Front Axle Spacer 1150 Bearing 2x9.8mm Pin 1510 Bearing Rear 1150 Bearing You can adjust front tread by position of Wheel Hub Spacer. 2x9.8mm Pin 1150 Bearing Wheel Hub Spacer 2x9.8mm Pin 2x9.8mm Pin Wheel Hub Wheel Hub Out Side Flat Tapered In Side 3x3mm Set Screw Tapered Spacer ASSEMBLE SUSPENSION PARTS Tapered Spacer Aluminum Spacer Tapered Spacer Aluminum Spacer 3X10mm Button Front Rear Body Post Long Body Post Short Fit Dog bone in the slit of Diff joint before tighten Steering ball in 2.5mm Allen Wrench.. Aluminum Spacer 3X10mm Button Tapered Spacer 3x3mm Set Screw Flat Tapered Tapered Spacer Tighten Steering Ball in 2.5mm Allen Wrench. **Do not too much tight. 5

7 SERVO SAVER 3x8mm Button Servo Mount Steering Servo 3mm Washer Change direction 3x30mm Set Screw 3x30mm Set Screw Servo Rod : 49mm Ball End Long 3x30mm Set Screw 3mm Washer 3x8mm Button Servo Saver Ball End Long Use this part that fit for each servo. 1.5mm Hex Wrench Keep symmetrical, Right and Left. Futaba TAMIYA Airtronics KO JR Mini-Servo 12 Use the screw that comes with Servo. Change direction 3x10mm Flat 3X6mm Hex Cap Screw Deck Pillar When the Power is on, the Servo Horn should be in the neutral position as shown in the picture. INSTALLATION SERVO AND MOTOR 3x3mm Set Screw 3x10mm Flat 540 Size Motor Copy Paper 3x3mm Set Screw Adjust the position of the pinion gear to put the centers of two gears together. Then fix it with a set screw. To get a perfect gear mesh, place a piece of paper between the gears and tighten the motor mount screws. Adjust motor position for smooth gear mesh. 3X6mm Hex Cap Screw 1.5mm Hex Wrench Pinion Gear 3X6mm Hex Cap Screw 6

8 3x10mm Button 3x8mm Button UPPER DECK 3x10mm Button 3x10mm Button 3x12 Set Screw 3x12 Set Screw 3x8mm Button Head Screw 1.5mm Hex Wrench Steering Tie Rod (Make 2 sets) Ball End Short Steering Tie Rod 3x12 Set Screw Ball End Short Keep symmetrical, Right and Left. Steering Tie Rod : 28mm SHOCK ABSORBER 2.0mm E-Clip Dumper Piston (1.2 x 2) Shock Cap A Dumper Top Shock Shield 2.0mm E-Clip Shock Body Shock shaft Fill Shock Oil, when piston is bottom. P3 O Ring Move the Shock Shaft up and down slowly to remove all air bubbles. Attach Shock Cap A, when Piston is top. Shock Cap B Spring Stopper A **Use Hobby Knife 2.0mm E-Clip Maximum Length for Front Dumper Spring Shock shaft Front Rear Maximum Length for Rear Spring Stopper B P3 O Ring Ball End Short for Front Shock Shield Dumper Adjust 2mm Dumper Adjust 4mm Ball End Long for Rear Ball End Short Ball End Long Use masking tape to protect Shock Shaft. Screw Ball End all of the way onto the Shock Shaft. 7

9 SHOCK / RC ELECTRONICS Receiver Speed Contoroller Double Tape Rear Shock Ball End Long Front Shock Gear Ratio (48 Pitch) Ball End Short TIRES & WHEELS Rubber Cement Foam Insert Quick Cement Tire Foam Insert Wheel Spur Gear made by XENON **Clean up the oil of a wheel and the tire with a cleaner before gluing tires and wheels. 8

10 Body Clip 3x10mm Flat TIRES/BATTERY Battery 7.4V Lipo 7.2V Ni-cd Ni-MH 6.6V Li-fe Nylon Nut (3mm) Body Clip Nylon Nut (3mm) WHEEL NUT 4mm 3mm Washer 3mm Washer Straping Tape 3x10mm Flat Battery Holder 3mm Washer **Insert Between Main Chassis and Battery Tray Body Clip Antenna Cap ANTENNA / BODY Knife Edge Reamer (#69006) or Lexan Hole Punch 7mm (#69002) Sub-C Cells (Seperate WHEEL NUT 4mm Body Battery Tary Battery Gate 3x10mm Flat 3mm Washer **Adjust Washers by Battery Size Antenna Cap Body Clip Antenna Pipe Body Post on Front Bumper. You can choose from 2 Front Body Post Locations. 3x10mm Flat 9

11 BASIC SETTING Ackermann You can choose 2 deferent Ackermann setting by changing Ball Stud location on Steering Bridge. Front Toe Toe In 1 Standard Weight Balance More Steer on out side tire. You can choose 3 deferent position on Battery Tray. 230g Battery on mid position is Standard waight Balance Setting. Middle Position of Battery Tray (Standard) Toe In 3 Rear Toe Ride Height / Droop Droop 3mm Ride Height 5mm Front Rear Droop 3mm Ride Height 7mm Camber Front Rear

12 Body Post Battery Holder A Rear Lower Sus Arm Arm Holder B SHOCK PARTS Anti-Roll Bar Link Antenna Mount Battery Holder B Steering Ball Washer Rear Upper Sus Arm Long BALL CUP Short SHOCK BODY Bumper Servo Mount Arm Holder D Rear Upright Sus Arm Pin Ball Use Anti-Roll Bar Link with #24167 BUMPER/ BODY MOUNT STEERING/ ARM HOLDER Rear Sus. Arm / Knuckle set for STR System Knuckle Arm Front Upper Arm Lower Sus Arm Steering Ball Washer Wheel Hub Arm Holder A Steering Ball Washer Lower Sus Arm Knuckle Arm LOWER ARM/ KNUCKLE Goose Top Deck Goose Battery Tray UPPER ARM/ HOLDER Steering Bridge Goose Main Chassis LOWER ARM PIN UPPER ARM PIN 1 Set Diff Joint A Diff Joint B Front Shock Tower Rear Shock Tower DIFF JOINT CUP 1/8" BALL DIFF D CUT RING DIFF SCREW / NUT DIFF SPRING DIFF THRUST BEARING Ball Bearing 850 BALL BEARING 1510 SHIM DIFF OUT RING SHOCK BALL SHOCK SHAFT SHOCK SHIELD SHOCK CAP 4MM BALL STUD O-RING P3 E-RING 2.0mm Damper Spring (Goose Kit Standard) STEERING ROD

13 1 Set MG SERVO SAVER DOG BONE AXLE SHAFT 4X6X0.7T RING STEERING 7mm RING 2X9.8mm PIN WHEEL NUT 4mm STEERING BIG BALL With Insert Foam STEERING 7mm NUT GEAR HOLDER O-RING P8 2X7.8mm PIN BODY CLIP TTR Wheel, HS-White TTR N RACING TIRE Ball Bearing 1150 Ball Stud Deck Pillar Motor Holder Bulkhead Spacer 5.8mm x 11mm Pulley Mount Steering Wiper Nut Steering Pipe 1 Set Goose Front Axle Shaft Center Gear Shaft Steering Post E-Ring 3.0mm E-Ring 4.0mm Goose Screw Set Drive Belt ANTENNA TUBE Pinion Gear 32T Spur Gear 84T Battery Holder A F63 Plastic Bearing Steering Shaft Spacer Wheel Hub Spacer Center Gear Spacer 5x8x1.6 Center Gear Spacer 5x8x5.7 Center Gear Spacer 5x8x2.3 STR Ball Stud Base Skid Plate Battery Holder B Rear Upper Bulkhead Front Bulkhead Rear Lower Bulkhead Axle Spacer Belt Tensioner Upper Suspension Holder Goose Bulkhead Anti-Roll Bar Holder Steering Wiper Left Steering Wiper Right 84 Plastic Bearing 84 Plastic Bearing Steering Arm Goose Steering Unit Goose Straight Battery Holder Diff Pulley 35T Center Pulley 17T (Standard) Body Post Short Body Post Long Center Pulley 15T Diff Pulley Franege Center Pulley Franege Goose Diff Pulley Goose Small Pulley Goose Body Post

14 KNUCKLE / REINFORCED HEAVY DUTY SERVO SAVER ALUM. SERVO MOUNT ADJUSTABLE SPACER SET Heavy Duty Sus. Arm Pin S Heavy Duty Sus. Arm Pin L Metal Sus. Arm STEERING BIG Pin Ball BALL/ LONG REINFORCED ALUM. DOG BONE S (32.5mm) REINFORCED ALUM. DOG BONE M (34.5mm) REINFORCED ALUM. UPGRADE DIFF DOG BONE L (36.5mm) ALUM. HUB 5mm ALUM. HUB 6mm ALUM. HUB 7mm SCREW/NUT Teflon Steering Ball Washer (Goose Kit Stock) TTR Wheel, TTR RIMS/ BLACK, RIMS/ WHITE, Wheel, TTR TTR Wheel, TTR Wheel, Wheel, TTR Wheel, REINFORCED REINFORCED HS, White HS, Black S-Mesh, White S-Mesh, Black BRE, White BRE, Black Use Anti-Roll Bar Link from #24023 (Include Kit) Blue Yellow White You can use front or rear. ANTI ROLL BAR SET (4 in Set) Accuracy Aluminum Dumper Blue Red Copper Purple Yellow White 6 Pair Springs in Set SHOCK SPRING SET ALUM. ARM HOLDER A ALUM. ARM HOLDER B ALUM. DIFF JOINT ALUM. UPPER SUS-HOLDER ALUM. FRONT BULKHEAD ALUM. CENTER BULKHEAD ALUM. REAR UPPER BULKHEAD ALUM. REAR LOWER BULKHEAD ALUM. BATTERY GATE 2 Types in Set SLIPPER CLUTCH (10g x 2) Extra Weight Ball Bearing 3x6F Ball Bearing 4x8 Skid Type Diffuser Type GOOSE MOTOR GUARD CARBON CHASSIS SET

DIFFERENTIAL STEERING RACK

DIFFERENTIAL STEERING RACK BAG-A DIFFERENTIAL (2 Sets) +Driver Cap Screw Diff Ball Nylon Nut Thrust Washer Thrust Ball Diff Joint Cup A Allen Wrench 850 Bearing Diff Ring Diff Spring Nylon Nut 850 Bearing Diff Ring Diff Ball Ball