along with standard XT2 Instruction Manual and also XT2 18 Supplementary Sheet.

Size: px
Start display at page:

Download "along with standard XT2 Instruction Manual and also XT2 18 Supplementary Sheet."

Transcription

1 Use this XT2 Dirt Conversion Supplementary Sheet along with standard XT2 Instruction Manual and also XT2 18 Supplementary Sheet. Parts included in Bag 8: SHIM 3x5x1.0MM (10) XT2 COMPOSITE SUSPENSION ARM FRONT LOWER COMPOSITE MID MOTOR GEAR BOX (3 GEARS) SET XT2 GRAPHITE SHOCK TOWER REAR 4.0MM XT2 COMPOSITE SUSPENSION ARM REAR LOWER XT2 GRAPHITE REAR SHOCK TOWER ADJUSTING SHIM 4.0MM (2) MID & REAR MOTOR PLATE - SWISS 7075 T6 (3MM) COMPOSITE MOTOR UPPER BRACE - DIRT EDITION COMPOSITE GEAR COVER - DIRT EDITION COMPOSITE GEAR 25T - GRAPHITE BALL ADJUSTABLE DIFFERENTIAL XH - SET - HUDY SPRING STEEL M COMPOSITE BATTERY STRAP - - DIRT EDITION REAR ARM PIVOT PIN (2) HEX SCREW SB M3x4 (10) HEX SCREW SH M3x6 (10) HEX SCREW SH M3x12 (10) HEX SCREW SH M3x14 (10) HEX SCREW SH M3x18 (10) HEX SCREW SH M3x40 (10) HEX SCREW SFH M3x6 (10) HEX SCREW SFH M3x22 (10) 1

2 1. BALL DIFFERENTIAL BALL DIFFERENTIAL (FACTORY PRE-ASSEMBLED) BALL DIFFERENTIAL SPRING BALL ADJUSTABLE DIFFERENTIAL XH - SET - HUDY SPRING STEEL BALL DIFF SHORT OUTPUT SHAFT XH - HUDY SPRING STEEL BALL DIFF LONG OUTPUT SHAFT XH - HUDY SPRING STEEL COMPOSITE BALL DIFFERENTIAL GEAR 53T SCREW FOR BALL DIFF ADJUSTMENT - SPRING STEEL BALL DIFFERENTIAL NUT DIFF WASHER 17 x 24.5 x 1 (2) CARBIDE BALL 2.4MM FOR BALL DIFF (12) CARBIDE BALL-BEARING AXIAL F3-8 3x8x3.5 - V BALL-BEARING 5x8x2.5 (2) CH-CLIP 8 - GRINDED (2) NOTE ORIENTATION BA 3x8x NOTE ORIENTATION GRAPHITE GREASE (HUDY #106210) C 8 Insert CH-clip into the groove with snap ring pliers (HUDY #189040) 2

3 1. BALL DIFFERENTIAL BB 5x8x2.5 DIFF GREASE (HUDY #106211) CUTAWAY VIEW OIL BEARING OIL (HUDY #106230) Square shape orientation on TOP side. Round shape orientation on BOTTOM side B 2.4 DIFF GREASE (HUDY #106211) DIFF GREASE (HUDY #106211) THREAD LOCK 2.0 IMPORTANT: When you build the differential, do not tighten it fully initially; the differential needs to be broken in properly. When you build the diff tighten it very gently. When you put the diff in the car and complete the assembly, run the car for a few minutes, tighten the diff a little bit, and then recheck the diff. Repeat this process several times until you have the diff tightened to the point you want it. Final adjustments should ALWAYS be made with the diff in the car and on the track. To access the diff when it is installed in the car, you need to remove the camber linkage on the side from which the diff screw is installed. This will detach the suspension. Then use a 2 hex wrench to adjust the diff. CUTAWAY VIEW 3

4 BALL DIFF BREAK-IN & SET-UP INFO The differential is factory pre-assembled including all greases, but is NOT ready to race iediately. BEFORE RACING, follow these steps to properly break in the differential. INITIAL BALL DIFFERENTIAL BREAK-IN Loosen the adjustment screw ¼ turn (90 CCW). 2.0 LOOSEN THE ADJUSTMENT SCREW ¼ (90 CCW) Rest the car on a flat surface (such as a table) and hold the left rear wheel securely in your hand. Apply 15% throttle to let the right rear wheel spin freely off the ground. Do this for about seconds. Release the throttle so the wheels do not spin. HOLD THE LEFT REAR WHEEL 15% THROTTLE (10-15 SECONDS) TABLE Switch sides, and hold the right rear wheel securely in your hand. Again apply 15% throttle to let the left rear wheel spin for seconds. Release the throttle so the wheels do not spin. HOLD THE RIGHT REAR WHEEL 15% THROTTLE (10-15 SECONDS) TABLE Tighten the ball diff turn (CW) with a 2 hex wrench. 2.0 TIGHTEN THE BALL DIFF (CW) Now repeat the above process again but this time apply 30% throttle. Rest the vehicle on a flat surface (such as a table) and hold the left rear wheel securely in your hand. Apply 30% throttle to let the right rear wheel spin freely off the ground. Do this for about seconds. Release the throttle so the wheels do not spin. HOLD THE LEFT REAR WHEEL 30% THROTTLE (10-15 SECONDS) TABLE Switch sides, and hold the right rear wheel securely in your hand. Again apply 30% throttle to let the left rear wheel spin for seconds. Release the throttle so the wheels do not spin. HOLD THE RIGHT REAR WHEEL 30% THROTTLE (10-15 SECONDS) TABLE ➐ Tighten the ball diff turn (CW) with a 2 hex wrench. This completes the INITIAL break-in process. 2.0 TIGHTEN THE BALL DIFF (CW) 4

5 BALL DIFF BREAK-IN & SET-UP INFO SLIPPER CLUTCH & BALL DIFFERENTIAL ADJUSTMENT It is critical that the slipper clutch and ball diff tension be set so that the slipper clutch always slips FIRST before the ball diff. The ball diff should NEVER slip as this will damage diff balls and diff washers. SLIPPER CLUTCH ALWAYS SLIPS FIRST THE BALL DIFF SHOULD NEVER SLIP BEFORE 1ST RUN Place the car on a flat table and hold both rear wheels. Apply short bursts of 100% full throttle. The front suspension should extend fully, but the front wheels should NOT lift off the ground. If needed, tighten or loosen the slipper adjustment nut as required. 100% THROTTLE HOLD REAR WHEELS INCORRECT The front suspension slightly lifts up. HOLD REAR WHEELS CORRECT 1ST RUN IMPORTANT During the first round listen to the car for metallic slipping sounds. If you hear metallic slipping sounds it means your differential is set too loose. Tighten the differential only turn (CW) and recheck. YOU SHOULD NOT HEAR METALLIC SLIPPING SOUNDS AFTER 1ST RUN After the first run, check again for the proper slipper and ball diff adjustment with the same procedure. Place the car on a flat table and hold both rear wheels. Apply short bursts of 100% full throttle. The front suspension should extend fully, but the front wheels should not lift off the ground. If needed, tighten or loosen the slipper adjustment nut as required. 100% THROTTLE HOLD REAR WHEELS INCORRECT The front suspension slightly lifts up. HOLD REAR WHEELS CORRECT 5

6 2. REAR TRANSMISSION 3 GEAR REAR TRANSMISSION SLIPPER CLUTCH SPUR GEARS # T / 48 (OPTION) # T / 48 (OPTION) # T / 48 (INCLUDED) # T / 48 (OPTION) # T / 48 (OPTION) SHIM 3x5x1.0MM (10) COMPOSITE MID MOTOR GEAR BOX (3 GEARS) SET MID & REAR MOTOR PLATE - SWISS 7075 T6 (3MM) TOP SHAFT 20T - SWISS 7075 T6 - COATED PAD SLIPPER CLUTCH PLATE - SWISS 7075 T PAD SLIPPER CLUTCH PLATE WITH ADAPTER PAD SLIPPER CLUTCH SHIM COMPOSITE GEAR 25T - GRAPHITE SLIPPER CLUTCH PAD SLS - V2 (2) PAD SLIPPER CLUTCH PLATE DISC T SLIPPER CLUTCH SPRING C=30 - BLACK COMPOSITE 3-PAD SLIPPER CLUTCH SPUR GEAR 75T / 48 (OPTION) COMPOSITE 3-PAD SLIPPER CLUTCH SPUR GEAR 78T / 48 (OPTION) COMPOSITE 3-PAD SLIPPER CLUTCH SPUR GEAR 81T / COMPOSITE 3-PAD SLIPPER CLUTCH SPUR GEAR 84T / 48 (OPTION) COMPOSITE 3-PAD SLIPPER CLUTCH SPUR GEAR 87T / 48 (OPTION) HEX SCREW SH M3x14 (10) HEX SCREW SH M3x40 (10) BALL-BEARING 3x8x4 (2) HIGH-SPEED BALL-BEARING 5x14 RUBBER SEALED (2) HIGH-SPEED BALL-BEARING 6x13x5 RUBBER SEALED (2) NUT M4 (10) PIN 3x20 (10) PIN 3x10 (10) P 3x10 3x P 3x20 3x20 3x10 6

7 2. REAR TRANSMISSION BB 3x8x SHIM 3x5x1 GRAPHITE GREASE (HUDY #106210) OIL 25T 3x5x1 3x5x1 OIL BEARING OIL (HUDY #106230) BB 5x14 OPEN 6x13x BB 6x13x5 OIL BEARING OIL (HUDY #106230) OIL 5x SH M3x40 CLOSED 7

8 2. REAR TRANSMISSION SLIPPER CLUTCH SPUR GEARS # T / 48 (OPTION) # T / 48 (OPTION) # T / 48 (INCLUDED) # T / 48 (OPTION) # T / 48 (OPTION) N M4 Flush with end of shaft SH M3x14 8

9 Follow the XT2 Instruction Manual for specific steps. 3. REAR SUSPENSION PAGE 13 / STEP SFH M3x6 REAR SUSPENSION ARMS # M INCLUDED # H INCLUDED # G GRAPHITE OPTION - For very-low & low traction - For medium & high traction GRAPHITE - For high & very-high traction 3. REAR SUSPENSION PAGE 13 / STEP SFH M3x22 # BALL ADJUSTABLE DIFFERENTIAL XH SET - HUDY SPRING STEEL 9

10 3. REAR DRIVETRAIN PAGE 15 / STEP SHIM 3x6x2 Ensure that the rear upright moves freely. If it does not move freely, use sandpaper to thin both wheelbase adjustment shims SH M2.5x4 3x6x WASHER S 2.5 3x6x2 TIGHTEN GENTLY TIGHTEN GENTLY LONGER WHEELBASE (INITIAL SETTING) Adjustment Shim IN FRONT OF HUB moves hub rearward. ARM Check for free movement SHORTER WHEELBASE Adjustment Shim BEHIND HUB moves hub forward. ARM 3. REAR DRIVETRAIN PAGE 16 / STEP 1 THREAD 8 THREAD 56.8 THREAD 10 THREAD 3. REAR DRIVETRAIN PAGE 16 / STEP SH M3x10 Larger diameter hole 10

11 3. REAR DRIVETRAIN PAGE 16 / STEP SH M3x18 4. FRONT ASSEMBLY PAGE 18 / STEP SH M3x SFH M3x SFH M3x SFH M3x18 GRAPHITE SIDE GUARD BRACE # SOFT OPTION # OPTION # STIFF INCLUDED SOFT - For very-low, low traction tracks. - For low & medium traction tracks. STIFF - For high- & very-high traction tracks. FRONT LOWER CHASSIS BRACE # M OPTION # H INCLUDED 3x10 3x18 3x8 - For very-low, low & medium traction. Generates more traction. - For high- & very-high traction tracks. More stable and less traction on front susp. 11

12 5. FRONT SUSPENSION PAGE 21 / STEP 1 NOTE ORIENTATION SH M2.5x WASHER S 2.5 NOTE ORIENTATION TIGHTEN GENTLY SUSPENSION ARM # M INCLUDED # H INCLUDED # G GRAPHITE OPTION - For very-low & low traction - For medium & high traction GRAPHITE - For high & very-high traction 5. FRONT SUSPENSION PAGE 22 / STEP SHIM 3x6x1 3x6x SH M2.5x WASHER S 2.5 NOTE ORIENTATION 2.5º CUTAWAY VIEW CASTER ECCENTRIC BUSHINGS 0º LESS CASTER = increased steering off-power MORE CASTER = less steering off-power 2.5º 5º INITIAL SETTING 5. FRONT SUSPENSION PAGE 23 / STEP 3 STEERING LINKS THREAD 56.1 THREAD 12

13 5. FRONT SUSPENSION PAGE 23 / STEP 4 STEERING LINKS SFH M3x NUT M3 6. SHOCK ABSORBERS HUDY Premium Silicone Oils Oil 500cSt (#106350) HUDY Premium Silicone Oils Oil 650cSt (#106365) O 3x2.1 REAR SHOCK (LONG) Oil 500cSt FRONT SHOCK (SHORT) Oil 650cSt 7. FINAL ASSEMBLY PAGE 30 / STEP NUT M3 INITIAL SETTING SH M3x10 INITIAL SETTING 7. FINAL ASSEMBLY PAGE 31 / NEW STEP SH M3x6 13

14 7. FINAL ASSEMBLY PAGE 31 / STEP SH M3x10 3x SFH M3x SFH M3x10 INNER position - increases traction (INITIAL SETTING) OUTER position - increases stability 3x8 3x10 3x10 7. FINAL ASSEMBLY PAGE 31 / NEW STEP SB M3x4 BATTERY STRAP # M INCLUDED # H 7. FINAL ASSEMBLY PAGE 3x SH M3x SH M3x x12 OPTION 31 / PAGE 2

15 APPLIED APPLIED RACE LONGER BUSHINGS TRACK DATE LAPS BEST LAP TIME sec TRACK SIZE 32 1 OTHER STEERING BLOCK FINAL POSITION QUALIFYING POSITION UPPER SHOCK POSITION SHIM CAMBER LINK LOCATION 2 1 OTHER OPEN TIGHT TRACTION VERY-LOW LOWER SHOCK POSITION VERY-HIGH SMOOTH BUMPY TYPE CLAY CARPET ASTRO CONDITION CASTER BUSHINGS 0 BLUE GROOVE PACKED DRY DUSTY LOAMY WET 2.5 CAS T BALL DIFF GEAR DIFF SATELITE GEARS COMPOSITE SLIPPER OTHER STEEL 3 GEARS PINION KICK-UP ANGLE 4 GEARS T SPUR GEAR cst % REBOUND PISTONS % BUMP STEER SHIM HOLES INSERT UNDER PISTON INSERT UNDER PISTON LENGTH LENGTH UPSTOP SHIM RF COMPOSITE BRASS RR 1 REAR TOE EXTENSION ROLL CENTER HOLDER OFFSET SLOTS FLEX LINKAGE YES SCREW NO ROLL CENTER NO MOTOR MOUNT BRACE SCREW 2 1 BATTERY STRAP UPPER DECK ROLL CENTER HOLDER GRAPHITE GUARD BRACE SOFT STIFF COMPOSITE FRONT CAMBER ANTI ROLL BARS ROLL CENTER UPPER BRACE SCREW COMPOSITE GRAPHITE SHOCK TOWER THICKNESS IN FRONT OF ARM YES KIT GRAPHITE IN WHEELBASE SHIM INSERT ABOVE COLLAR BALL JOINT BRASS SUSPENSION HOLDERS 0 SLOTS 1 SLOT 2 SLOTS INSERT ABOVE COLLAR 0.5 UPSTOP SHIM 1 SHIMS COMPOSITE OFFSET 0 DOWNSTOP SHIM COMPOSITE ECCENTRIC BUSHINGS IN FRONT OF ARM 6 HOLES ø REAR ROLL CENTER SHIMS WHEELBASE SHIM 3 HOLES GRAPHITE LOWER SHOCK POSITION 2 HOLES DOWNSTOP SHIM KIT SLOTS ø1.2 ø1.3 ø1.4 ø1.6 ø1.7 ø FRONT STEERING PLATE FRONT TOE OIL HOLES STEERING ARMS OUT cst 6 HOLES T SPRINGS 3 HOLES STEERING BUMP STEER 23 KIT SHOCKS 2 HOLES REAR SHIM ACKERMANN LEFT = RIGHT cst GEARING GEAR BOX GEAR REAR UPRIGHT FRONT LEFT = RIGHT OIL ADJUSTMENT DRIVE SHAFT CVD ECS SHIM BUMP STEER SHIM ER 5 TRANSMISSION DIFFERENTIAL... SURFACE NAME CASTER BLOCK UP DOWN SIDE GUARD COMPOSITE UPPER BRACE KIT OTHER OTHER - - REAR CAMBER FRONT ARM TIRES TYPE INSERTS REAR ARM GRAPHITE GRAPHITE RIDE HEIGHT WHEELS RIDE HEIGHT # GAUGE RIDE HEIGHT ELECTRONICS MOTOR SPEEDO CHASSIS BRACE BATTERIES ELECTRONICS LAYOUT MOTOR POSITION FRONT MIDDLE REAR BATTERY POSITION FRONT MIDDLE REAR BODY STANDARD LIGHT OTHER SERVO WEIGHT STANDARD BALANCE BALANCE g g LOW PROFILE HIGH ARM MOUNT WING COMPOSITE BRASS STANDARD CHASSIS OTHER CHASSIS FLEX SCREW USED SCREW NOT USED NONE HIGH / XT2'18 SET-UP SHEET VER. 1 XRAY 2017

16 RC AMERICA, 2030 Century Center Blvd #15, Irving, TX 75062, USA PHONE: , FAX: , /TeamXray /TeamXray /TeamXray /TeamXrayRC /XrayRacing /XrayRacing

Use this NT Supplementary Instruction Sheet along with the standard NT1 Instruction Manual included in the kit.

Use this NT Supplementary Instruction Sheet along with the standard NT1 Instruction Manual included in the kit. INSTRUCTION MANUAL SUPPLEMENTARY SHEET Use this NT1 2013 Supplementary Instruction Sheet along with the standard NT1 Instruction Manual included in the kit. New and Improved Parts All of these parts are

More information

BEFORE YOU START. XRAY Europe K Výstavisku 6992, Trenčín Slovakia EUROPE. XRAY USA RC America, 2030 Century Center Blvd #15 Irving, TX USA

BEFORE YOU START. XRAY Europe K Výstavisku 6992, Trenčín Slovakia EUROPE. XRAY USA RC America, 2030 Century Center Blvd #15 Irving, TX USA BEFORE YOU START The X12 is a high-quality, 1/12-pan car intended for persons aged 16 years and older with previous experience building and operating RC model racing cars. This is not a toy; it is a precision

More information

BEFORE YOU START CUSTOMER SUPPORT

BEFORE YOU START CUSTOMER SUPPORT BEFORE YOU START The X10 is a high-quality, 1/10-pan car intended for persons aged 16 years and older with previous experience building and operating RC model racing cars. This is not a toy; it is a precision

More information

Failure to follow these instructions will be considered as abuse and/or neglect.

Failure to follow these instructions will be considered as abuse and/or neglect. 1 INTRODUCTION The XRAY XB2 is a modern, high-competition premium luxury racing 1/10 electric 2WD off-road buggy that is the epitome of high-performance and fine distinctive design. Your XB2 offers highest

More information

BEFORE YOU START. XRAY USA RCAmerica, 167 Turtle Creek Boulevard Suite C Dallas, Texas 75207, USA

BEFORE YOU START. XRAY USA RCAmerica, 167 Turtle Creek Boulevard Suite C Dallas, Texas 75207, USA BEFORE YOU START The X12 is a high-quality, 1/12-pan car intended for persons aged 16 years and older with previous experience building and operating RC model racing cars. This is not a toy; it is a precision

More information

INSTRUCTION MANUAL SUPPLEMENTARY SHEET

INSTRUCTION MANUAL SUPPLEMENTARY SHEET INSTRUCTION MANUAL SUPPLEMENTARY SHEET The T3R Raycer is based on the hugely-successful, race-winning T3 and as such the majority of spare parts and option parts are fully compatible between the two cars.

More information

Failure to follow these instructions will be considered as abuse and/or neglect.

Failure to follow these instructions will be considered as abuse and/or neglect. INTRODUCTION The XRAY XB2 is a modern, high-competition premium luxury racing 1/10 electric 2WD off-road buggy that is the epitome of high-performance and fine distinctive design. Your XB2 offers highest

More information

INTRODUCTION SAFETY PRECAUTIONS IMPORTANT NOTES GENERAL

INTRODUCTION SAFETY PRECAUTIONS IMPORTANT NOTES GENERAL INTRODUCTION The XRAY XB2 is a modern, high-competition premium luxury racing 1/10 electric 2WD off-road buggy that is the epitome of high-performance and fine distinctive design. Your XB2 offers highest

More information

=Apply Thread lock adhesive. =Apply CA Glue =Apply Grease NOTE : BAG 01 BAG 01 BAG mm. When track High Traction or want to reduce steering

=Apply Thread lock adhesive. =Apply CA Glue =Apply Grease NOTE : BAG 01 BAG 01 BAG mm. When track High Traction or want to reduce steering NOTE : =Apply Thread lock adhesive R80059 One Way Cup () R8009 One Way R80 Pulley Set- R80004 Alu-Bulkhead-L BAG 0 CA GE =Apply CA Glue =Apply Grease R8000 Upper Arm Bracket Base R8004 One Way Plastic

More information

INTRODUCTION SAFETY PRECAUTIONS IMPORTANT NOTES GENERAL

INTRODUCTION SAFETY PRECAUTIONS IMPORTANT NOTES GENERAL 2O16 INTRODUCTION The XRAY XB4 is a modern, high-competition premium luxury racing 1/10 electric 4WD off-road buggy that is the epitome of high-performance and fine distinctive design. Your XB4 offers

More information

Pinion Gear and Setscrew

Pinion Gear and Setscrew XRAY T1 Factory Kit 2005 The new XRAY T1 Factory Kit '05 (T1FK'05) is the 5th generation of XRAY's extremely successful T1 family of 1/10-scale on -road electric touring cars. The T1FK'05 is a large evolutionary

More information

INTRODUCTION FAILURE TO FOLLOW THESE INSTRUCTIONS WILL BE CONSIDERED AS ABUSE AND/OR NEGLECT.

INTRODUCTION FAILURE TO FOLLOW THESE INSTRUCTIONS WILL BE CONSIDERED AS ABUSE AND/OR NEGLECT. 1 INTRODUCTION The XRAY XT2 is a modern, high-competition premium luxury racing 1/10 electric 2WD off-road buggy that is the epitome of high-performance and fine distinctive design. Your XT2 offers highest

More information

Failure to follow these instructions will be considered as abuse and/or neglect.

Failure to follow these instructions will be considered as abuse and/or neglect. INTRODUCTION The XRAY XB4 is a modern, high-competition premium luxury racing 1/10 electric 4WD off-road buggy that is the epitome of high-performance and fine distinctive design. Your XB4 offers highest

More information

=Apply Thread lock adhesive. =Apply CA Glue =Apply Grease NOTE : BAG 01 BAG 01 BAG 01. R Front One Way Cup (2) R Front One Way

=Apply Thread lock adhesive. =Apply CA Glue =Apply Grease NOTE : BAG 01 BAG 01 BAG 01. R Front One Way Cup (2) R Front One Way NOTE : =Apply Thread lock adhesive R80059 One Way Cup () R8009 One Way R80 Pulley Set- R80004 Alu-Bulkhead-L BAG 0 =Apply Glue =Apply Grease R8000 Upper Arm Bracket Base R8004 One Way Plastic Shims ()

More information

=Apply Thread lock adhesive. =Apply CA Glue =Apply Grease NOTE : BAG 01 BAG 01 BAG 01

=Apply Thread lock adhesive. =Apply CA Glue =Apply Grease NOTE : BAG 01 BAG 01 BAG 01 NOTE : =Apply Thread lock adhesive R80059 One Way Cup R8009 One Way R80 Pulley Set- R80004 Alu-Bulkhead-L BAG 0 =Apply Glue =Apply Grease R8000 Upper Arm Bracket Base R8004 One Way Plastic Shims () R80005

More information

ROLL CENTER You can adjust the front and rear roll centers of the XB8 by changing the mounting locations of various components.

ROLL CENTER You can adjust the front and rear roll centers of the XB8 by changing the mounting locations of various components. Your XRAY XB8 luxury nitro buggy is a top competition, precision racing machine that features multiple adjustments that allow you to set up for any track condition. The XB8 includes innovative set-up features

More information

INTRODUCTION FAILURE TO FOLLOW THESE INSTRUCTIONS WILL BE CONSIDERED AS ABUSE AND/OR NEGLECT. SAFETY PRECAUTIONS IMPORTANT NOTES GENERAL

INTRODUCTION FAILURE TO FOLLOW THESE INSTRUCTIONS WILL BE CONSIDERED AS ABUSE AND/OR NEGLECT. SAFETY PRECAUTIONS IMPORTANT NOTES GENERAL INTRODUCTION The XB8E is a high-competition, high-quality, 1/8 electric off-road car intended for persons aged 16 years and older with previous experience building and operating RC model racing cars. This

More information

Bag 1. Bag 1. Center Pivot. Center Pivot

Bag 1. Bag 1. Center Pivot. Center Pivot 8 00734 01901 5 Center Pivot Bag 1 3374 - Center Pivot Socket 4019 - Alum Pivot ball 3254-2-56 Button Head *Note - Sometimes it is helpful to slightly over-tighten the top clamp screws, then work the ball

More information

Assembly Manual. 1/10th Formula 1 Car

Assembly Manual. 1/10th Formula 1 Car Assembly Manual 1/10th Formula 1 Car Center Pivot Bag 1 3374 - Center Pivot Socket 40194 - Hard Anodized Alum Pivot ball 3254-2-56 *Note - Sometimes it is helpful to slightly over-tighten the top clamp

More information

BEFORE YOU START SAFETY PRECAUTIONS IMPORTANT NOTES GENERAL

BEFORE YOU START SAFETY PRECAUTIONS IMPORTANT NOTES GENERAL BEFORE YOU START The X10 is a high-competition, high-quality, 1/10 pan car intended for persons aged 16 years and older with previous experience building and operating RC model racing cars. This is not

More information

BEFORE YOU START SAFETY PRECAUTIONS IMPORTANT NOTES GENERAL. Failure to follow these instructions will be considered as abuse and/or neglect.

BEFORE YOU START SAFETY PRECAUTIONS IMPORTANT NOTES GENERAL. Failure to follow these instructions will be considered as abuse and/or neglect. BEFORE YOU START The XB8E is a high-competition, high-quality, 1/8 electric buggy intended for persons aged 16 years and older with previous experience building and operating RC model racing cars. This

More information

BEFORE YOU START SAFETY PRECAUTIONS IMPORTANT NOTES GENERAL. carefully and fully understand the instructions before beginning assembly.

BEFORE YOU START SAFETY PRECAUTIONS IMPORTANT NOTES GENERAL. carefully and fully understand the instructions before beginning assembly. BEFORE YOU START The X12 is a high-competition, high-quality, 1/12 pan car intended for persons aged 16 years and older with previous experience building and operating RC model racing cars. This is not

More information

Failure to follow these instructions will be considered as abuse and/or neglect.

Failure to follow these instructions will be considered as abuse and/or neglect. INTRODUCTION The XRAY XT8 is a modern, high-competition premium luxury racing 1/8 nitro truggy that is the epitome of high-performance and fine distinctive design. Your XT8 offers highest performance,

More information

BEFORE YOU START SAFETY PRECAUTIONS IMPORTANT NOTES GENERAL. Failure to follow these instructions will be considered as abuse and/or neglect.

BEFORE YOU START SAFETY PRECAUTIONS IMPORTANT NOTES GENERAL. Failure to follow these instructions will be considered as abuse and/or neglect. BEFORE YOU START The X1 is a high-competition, high-quality, 1/10-scale Formula car intended for persons aged 16 years and older with previous experience building and operating RC model racing cars. This

More information

BEFORE YOU START SAFETY PRECAUTIONS IMPORTANT NOTES GENERAL. Failure to follow these instructions will be considered as abuse and/or neglect.

BEFORE YOU START SAFETY PRECAUTIONS IMPORTANT NOTES GENERAL. Failure to follow these instructions will be considered as abuse and/or neglect. BEFORE YOU START The T3 is a high-competition, high-quality, 1/10-scale touring car intended for persons aged 16 years and older with previous experience building and operating RC model racing cars. This

More information

Failure to follow these instructions will be considered as abuse and/or neglect.

Failure to follow these instructions will be considered as abuse and/or neglect. BEFORE YOU START The X1 is a high-competition, high-quality, 1/10-scale Formula car intended for persons aged 16 years and older with previous experience building and operating RC model racing cars. This

More information

ASSOCIATED 1:10 SCALE ELECTRIC BUGGY INSTRUCTION MANUAL FOR THE TEAM ASSOCIATED RC10B Associated Electrics, Inc. RS-1

ASSOCIATED 1:10 SCALE ELECTRIC BUGGY INSTRUCTION MANUAL FOR THE TEAM ASSOCIATED RC10B Associated Electrics, Inc. RS-1 ASSOCIATED 1:10 SCALE ELECTRIC BUGGY INSTRUCTION MANUAL FOR THE TEAM ASSOCIATED RC10B4 TT RS-1 2003-2006 Associated Electrics, Inc. FINAL ADJUSTMENTS RADIO ADJUSTMENTS Use the following

More information

Contents. Symbols Used. Equipment Required L=R. Page. Apply Thread Lock. Apply. Silicone Oil. 30mm Fan

Contents. Symbols Used. Equipment Required L=R. Page. Apply Thread Lock. Apply. Silicone Oil. 30mm Fan Contents Content Page Content Page Content Page 0. Tool and Accessories 1.Filing the Edges of the Chassis 2.Bulkhead Installation 3.Spur Gear Assembly 4.Front Spool Assembly 5.Gear Differential Assembly

More information

INTRODUCTION SAFETY PRECAUTIONS IMPORTANT NOTES GENERAL IMPORTANT NOTES NITRO ENGINES

INTRODUCTION SAFETY PRECAUTIONS IMPORTANT NOTES GENERAL IMPORTANT NOTES NITRO ENGINES WORLD CHAMPIONS INTRODUCTION The XRAY XT9 is a modern, high-competition premium luxury racing 1/8 nitro truggy that is the epitome of high-performance and fine distinctive design. Your XT9 offers highest

More information

TP02C. 1:10 Scale Radio Controlled Electric Powered 2WD Racing Buggy. Dimensions. Length 410mm Width 250mm Height 150mm

TP02C. 1:10 Scale Radio Controlled Electric Powered 2WD Racing Buggy. Dimensions. Length 410mm Width 250mm Height 150mm TP02C 1:10 Scale Radio Controlled Electric Powered 2WD Racing Buggy Dimensions Length 410mm Width 250mm Height 150mm Transmitter Preparation Power Switch Antenna 27MHzTransmitter Crystal T 27MHz ON Extend

More information

BEFORE YOU START SAFETY PRECAUTIONS IMPORTANT NOTES GENERAL. Failure to follow these instructions will be considered as abuse and/or neglect.

BEFORE YOU START SAFETY PRECAUTIONS IMPORTANT NOTES GENERAL. Failure to follow these instructions will be considered as abuse and/or neglect. BEFORE YOU START The X1 is a high-competition, high-quality, 1/10-scale Formula car intended for persons aged 16 years and older with previous experience building and operating RC model racing cars. This

More information

J & D Machine / Hyperdrive / MSA 3711 Moon Bend Rd. Chapel Hill, TN 37034

J & D Machine / Hyperdrive / MSA 3711 Moon Bend Rd. Chapel Hill, TN 37034 J & D Machine / Hyperdrive / MSA 3711 Moon Bend Rd. Chapel Hill, TN 37034 www.hyperdriveracing.com 1 You now own a state of the art 1/10 scale oval race car. The Hyperdrive Assault has gone through months

More information

BEFORE YOU START SAFETY PRECAUTIONS IMPORTANT NOTES GENERAL. Failure to follow these instructions will be considered as abuse and/or neglect.

BEFORE YOU START SAFETY PRECAUTIONS IMPORTANT NOTES GENERAL. Failure to follow these instructions will be considered as abuse and/or neglect. BEFORE YOU START The T4 is a high-competition, high-quality, 1/10-scale touring car intended for persons aged 16 years and older with previous experience building and operating RC model racing cars. This

More information

XRAY KITS M18 M18T M18MT PARTS NT18 NT18T NT18MT PARTS. o = option part x = standard included / fits

XRAY KITS M18 M18T M18MT PARTS NT18 NT18T NT18MT PARTS. o = option part x = standard included / fits PRO LiPo PRO USE THE DROP MENU TO FILTER THE SELECTION XRAY KITS o = option part x = standard included / fits 38 0000 XRAY - 4WD SHAFT DRIVE 1/18 MICRO CAR 38 0003 XRAY PRO LiPo - 4WD SHAFT DRIVE 1/18

More information

FAILURE TO FOLLOW THESE INSTRUCTIONS WILL BE CONSIDERED AS ABUSE AND/OR NEGLECT.

FAILURE TO FOLLOW THESE INSTRUCTIONS WILL BE CONSIDERED AS ABUSE AND/OR NEGLECT. BEFORE YOU START The GTX8 is a high-competition, high-quality, 1/10-scale nitro car intended for persons aged 16 years and older with previous experience building and operating RC model racing cars. This

More information

:: Additional Features Your new TC6 comes unassembled and requires the following items for completion. (refer to catalog section for suggestions):

:: Additional Features Your new TC6 comes unassembled and requires the following items for completion. (refer to catalog section for suggestions): 8/10 2 :: Introduction Thank you for purchasing this Team Associated product. This assembly manual contains instructions and tips for building and maintaining your new RC10TC6. Please take a moment to

More information

Shown with optional GFR-1017R Body Posts. J & D Machine / Hyperdrive / MSA 3711 Moon Bend Rd. Chapel Hill, TN

Shown with optional GFR-1017R Body Posts. J & D Machine / Hyperdrive / MSA 3711 Moon Bend Rd. Chapel Hill, TN Shown with optional GFR-1017R Body Posts J & D Machine / Hyperdrive / MSA 3711 Moon Bend Rd. Chapel Hill, TN 37034 www.hyperdriveracing.com 1 You now own a state of the art 1/10 scale oval race car. The

More information

BEFORE YOU START SAFETY PRECAUTIONS IMPORTANT NOTES GENERAL. Failure to follow these instructions will be considered as abuse and/or neglect.

BEFORE YOU START SAFETY PRECAUTIONS IMPORTANT NOTES GENERAL. Failure to follow these instructions will be considered as abuse and/or neglect. BEFORE YOU START The X12 is a high-competition, high-quality, 1/12 pan car intended for persons aged 16 years and older with previous experience building and operating RC model racing cars. This is not

More information

SAFETY PRECAUTIONS IMPORTANT NOTES GENERAL IMPORTANT NOTES NITRO ENGINES

SAFETY PRECAUTIONS IMPORTANT NOTES GENERAL IMPORTANT NOTES NITRO ENGINES INTRODUCTION The XRAY XB808 is a modern, high-competition premium luxury racing 1/8 nitro buggy that is the epitome of high-performance and fine distinctive design. Your XB808 offers highest performance,

More information

R R11 Eccentric Hub-Alu (4) R R11 Eccentric Hub-Alu (4) NOTICE. Pulley cover direction NOTICE BAG 01 NOTICE BAG 01

R R11 Eccentric Hub-Alu (4) R R11 Eccentric Hub-Alu (4) NOTICE. Pulley cover direction NOTICE BAG 01 NOTICE BAG 01 BAG BAG R Spool Axle Alu RA Front Spool Pulley Set 8T (4pcs) R Diff Gears (with Axle) Trim any excess flashing from the diff gear axle at the mold injection point. (pcs) (4pcs) R Spool Outdrive (pcs) R6

More information

Assembly Manual. 1/10th World GT car

Assembly Manual. 1/10th World GT car Assembly Manual 1/10th World GT car Center Pivot Bag 1 3374 - Center Pivot Socket 40194 - Hard Anodized Alum Pivot ball 3254-2-56 Button Head *Note - Sometimes it is helpful to slightly over-tighten the

More information

OWNER'S MANUAL Magnolia Ave., Chino, CA phone: (909) fax: (909)

OWNER'S MANUAL Magnolia Ave., Chino, CA phone: (909) fax: (909) OWNER'S MANUAL Carefully read through all instructions to familiarize yourself with the parts, construction techniques, and tuning tips outlined in this manual. Being able to grasp the overall design of

More information

OWNER'S MANUAL 2000 & ROAR National Champion

OWNER'S MANUAL 2000 & ROAR National Champion 2000 & 2001 ROAR National Champion OWNER'S MANUAL Carefully read through all instructions to familiarize yourself with the parts, construction techniques, and tuning tips outlined in this manual. Being

More information

1/10 Scale 4WD 200mm Gas Power Touring Car

1/10 Scale 4WD 200mm Gas Power Touring Car 1/10 Scale 4WD 200 Gas Power Touring Car STS PRO 10 Instruction Manual DIMENSIONS Length: 390 Width: 200 Height: 120 Weight (ready to run): About 1800g DRIVETRAIN Type: 3-belt 4WD Transmission: 2-speed

More information

IMP4CT 4wd buggy by Elcon Models

IMP4CT 4wd buggy by Elcon Models IMP4CT 4wd buggy by Elcon Models 1 Content Introduction... 3 Rear Assembly... 4 Front assembly... 15 Mid section assembly... 18 2 Introduction Welcome and thank you for choosing the Elcon Models IMP4CT

More information

Make these adjustments before racing

Make these adjustments before racing FINAL ADJUSTMENTS ADJUSTING CAMBER To set the camber we recommend using our supplied #1719 camber/rear toe-in gauge. When adjusting camber you need to have the car ready to run with no body. Make these

More information

New Generation Rear Wheel Drive

New Generation Rear Wheel Drive New Generation Rear Wheel Drive ABC HOBBY ORIGINAL RADIO CONTROL CAR Instruction Manual Study the instructions thoroughly before assembly. REAR 2 WHEEL DRIVE REAR MOUNTED MOTOR BELT DRIVE DOUBLE DECK CHASSIS

More information

Bag 1. Bag 1. Center Pivot. 3 Center Pivot Cap. Center Pivot

Bag 1. Bag 1. Center Pivot. 3 Center Pivot Cap. Center Pivot Battle Axe 2.0 1:10th Oval Weapon from Team CRC Assembly Manual 0 2. e Ax s tle Win s! t rd Ba s + bi C. ow CR T.Q Sn 0 20 servo and saver not included Part # 100 Calandra Racing Concepts 6785 Martin Street

More information

CONTENTS. All texts and images contained within this set-up book are copyright by XRAY. All rights reserved. XRAY

CONTENTS. All texts and images contained within this set-up book are copyright by XRAY. All rights reserved. XRAY CONTENTS Setting up the XRAY T3 3 Downstops 6 Ride Height 8 Droop 10 Track Width 12 Steering Throw Symmetry 13 Camber 14 Caster 16 Bump Steer 17 Ackermann 17 Toe 18 Tweak 20 Roll Center 24 Chassis Flex

More information

SOARSEIKI.Co.,Ltd

SOARSEIKI.Co.,Ltd SOARSEIKI.Co.,Ltd info@soarseiki.com 1 2 3 4 BAGS A1 FRONT AND REAR DIFF 5 BAGS A2 CENTER DIFF 5 BAGS B1 FRONT TRANSMISSION STEP B1-1 Apply a thiin layer of lubricant on the gear. GR160003 BE050110040

More information

Contents. # HUDY Caster Clip Remover Tool. # HUDY Chassis Balancing Tool. # HUDY 3mm Turnbuckle Tool

Contents. # HUDY Caster Clip Remover Tool. # HUDY Chassis Balancing Tool. # HUDY 3mm Turnbuckle Tool Contents Introduction 2 Radio Adjustments 3 Speed Control (ESC) Adjustments 3 Connecting the Motor 3 Motor Gearing 3 Rollout 5 Differential Adjustment 5 Tightening the Differentials 6 Loosening the Differentials

More information

#0980 Intimidator 7 Direct Drive Racing Kit

#0980 Intimidator 7 Direct Drive Racing Kit #0980 Intimidator 7 Direct Drive Racing Kit 1 Thank you for purchasing the Intimidator 7! Within this kit you will find a race winning car with over 30 years of Custom Works design and quality. The latest

More information

RJS2020 SPORT 3.2 1/10 PAN CAR KIT LESS ELECTRICS

RJS2020 SPORT 3.2 1/10 PAN CAR KIT LESS ELECTRICS RJS2020 SPORT 3.2 1/10 PAN CAR KIT LESS ELECTRICS THANKS FOR BUYING THE RJ SPEED 1/10 SPORT 3.2 KIT. THE ASSEMBLY WILL NOT BE DIFFICULT IF YOU READ THE TEXT, LOOK AT THE PICTURES, AND THE EXPLODED VIEW

More information

RJS2021 LTO SPORT OVAL RACER LESS ELECTRICS

RJS2021 LTO SPORT OVAL RACER LESS ELECTRICS RJS2021 LTO SPORT OVAL RACER LESS ELECTRICS THANKS FOR BUYING THE RJ SPEED 1/10 LTO SPORT KIT FOR OVAL RACING. THE ASSEMBLY WILL NOT BE DIFFICULT IF YOU READ THE TEXT, LOOK AT THE PICTURES, AND THE EXPLODED

More information

TIPS TO FINAL ASSEMBLY Radio installation. The Electronic speed control (ESC) and the receiver need to be mounted onto the chassis, using double sided

TIPS TO FINAL ASSEMBLY Radio installation. The Electronic speed control (ESC) and the receiver need to be mounted onto the chassis, using double sided TIPS TO FINAL ASSEMBLY Radio installation. The Electronic speed control (ESC) and the receiver need to be mounted onto the chassis, using double sided tape (not supplied.) Mount the ESC first on the chassis

More information

E Thank you for purchasing VBC Racing product. COMPETITION GRADE HIGH PERFORMANCE RADIO CONTROL RACING CAR CHASSIS KIT INSTRUCTIONS MANUAL

E Thank you for purchasing VBC Racing product. COMPETITION GRADE HIGH PERFORMANCE RADIO CONTROL RACING CAR CHASSIS KIT INSTRUCTIONS MANUAL COMPETITION GRADE HIGH PERFORMANCE RADIO CONTROL RACING CAR CHASSIS KIT 1/10 SCALE ELECTRIC COMPETITION FORMULA CAR KIT INSTRUCTIONS MANUAL E Thank you for purchasing VBC Racing product. Things that we

More information

.050 Allen key 1.5mm Allen key 1/16 Allen key 5/64 Allen key 3/32 Allen key Turnbuckle & 3/16 wrench

.050 Allen key 1.5mm Allen key 1/16 Allen key 5/64 Allen key 3/32 Allen key Turnbuckle & 3/16 wrench 1 Thank you for purchasing the Outlaw 4 Sprint Car! The Outlaw sprint car platform has been developed for loose dirt buggy tire racing. In this kit you will find the 4 th evolution of the car which features

More information

Additional equipment and parts needed: Tools needed: Disclaimer: Warnings: Warranty:

Additional equipment and parts needed: Tools needed: Disclaimer: Warnings: Warranty: Introduction Thank you for purchasing the Tekno RC SCT410 1/10th Scale Electric 4WD Competition Short Course Truck. The SCT410 represents the state-of-the-art in 1/10th Electric Short Course technology.

More information

RJS WB ELECTRIC T/F DRAGSTER KIT LESS ELECTRICS

RJS WB ELECTRIC T/F DRAGSTER KIT LESS ELECTRICS RJS2006 30 WB ELECTRIC T/F DRAGSTER KIT LESS ELECTRICS THANKS FOR BUYING THIS RJ SPEED DRAGSTER KIT. IT IS MADE FOR STRAIGHT LINE DRAG RACING AND MAY BE BROKEN IF RUN INTO SOLID OBJECTS REPEATEDLY AT HIGH

More information

carbon fiber before assembly. Sand glue to the edges and

carbon fiber before assembly. Sand glue to the edges and chassis and carbon fiber give you a before assembly. Sand glue to the edges and 5 BAG MARKED CA BAG MARKED M3x6 Flathead 4 03 4 05 BAG MARKED 2 10 13 Installing Steering System Shock Assembly M4x28

More information

DIFFERENTIAL STEERING RACK

DIFFERENTIAL STEERING RACK BAG-A DIFFERENTIAL (2 Sets) +Driver Cap Screw Diff Ball Nylon Nut Thrust Washer Thrust Ball Diff Joint Cup A Allen Wrench 850 Bearing Diff Ring Diff Spring Nylon Nut 850 Bearing Diff Ring Diff Ball Ball

More information

PREBUIL UILT ASSEMBLY AND OPERATION MANUAL

PREBUIL UILT ASSEMBLY AND OPERATION MANUAL PREBUIL UILT Length: 15.2" [385mm] Width: 13" [330mm] Height: 5.8" [147mm] Weight: 3.3 lb [1500g] Wheelbase: 11.6" [295mm] Technical Support Information For technical assistance, contact: DuraTrax Product

More information

7207 FRONT BULKHEAD, nylon FRONT BULKHEAD ALUMINUM SUPPORT HINGE PIN, inner, with clips, 1.675" pr GT RACING FRONT

7207 FRONT BULKHEAD, nylon FRONT BULKHEAD ALUMINUM SUPPORT HINGE PIN, inner, with clips, 1.675 pr GT RACING FRONT RC10GT & RTR GT MC 9 McCOY GLOW PLUG 1 3.9 2661 CLUTCH NUT CLIPS 6.7 3216 WASHER, #4 12 1.00 3719 NYLON WIRE TIES, 6" heavy duty 12 2.00 3720 NYLON TIES, 8", light duty for receiver 12 2.00 3721 SELF-TAPPING

More information

1/8TH SCALE 4WD COMPETITION CAR INSTRUCTION MANUAL

1/8TH SCALE 4WD COMPETITION CAR INSTRUCTION MANUAL /8TH SCALE WD COMPETITION CAR INSTRUCTION MANUAL INTRODUCTION The Serpent 960 is the next evolution of Serpent s hugely-successful 90 lineage, combining ultimate performance into a single package. The

More information

INTRODUCTION INSTRUCTIONS. plastic parts CONTENTS

INTRODUCTION INSTRUCTIONS. plastic parts CONTENTS INTRODUCTION Thank you very much for selecting this Serpent rc car and thus become a member of the ever growing worldwide Serpent racing family. Serpent started in 980 and has been growing its product-line

More information

ASSEMBLY OF THE FRONT AND REAR BALL DIFF. Builds two differentials for front and rear

ASSEMBLY OF THE FRONT AND REAR BALL DIFF. Builds two differentials for front and rear 1 ASSEMBLY OF THE FRONT AND REAR BALL DIFF. 37145 40060 40060 2.6mm Nylon Nut 37110 35958 37132 2.6x6x1mm Washer 37148 Apply Grease 37120 (12 Pcs) Builds two differentials for front and rear. 38288 35958

More information

ON ROAD SETUP GUIDE PART ONE

ON ROAD SETUP GUIDE PART ONE PART ONE Ride height is adjusted by the preload of the spring collars. Winding them down will raise the ride height, while winding them up will decrease the ride height. It is important to note that adjusting

More information

3.0 Tuning Tips. To Shut Off the Engine: Use the included pipe plug or simply bump the flywheel with a wrench or plastic handled tool.

3.0 Tuning Tips. To Shut Off the Engine: Use the included pipe plug or simply bump the flywheel with a wrench or plastic handled tool. TM 8IGHT 3.0 Tuning Tips Before you start making changes on your 8IGHT 3.0 Off-Road Racing buggy, you need to make a few decisions. First of all, tires, and how they are setup, have a tremendous impact

More information

INSTRUCTION MANUAL INSTRUCTION MANUAL

INSTRUCTION MANUAL INSTRUCTION MANUAL INSTRUCTION MANUAL INSTRUCTION MANUAL Thank you for purchasing Pro-Line s PRO-Fusion SC 4 4! For Over 35 years, Pro-Line has designed and manufactured the best RC products in the world. This 1:10 scale

More information

2103 NITRO RAIL DRAGSTER KIT

2103 NITRO RAIL DRAGSTER KIT 203 NITRO RAIL DRAGSTER KIT THANKS FOR BUYING RJ SPEED S NITRO DRAG KIT. IT IS A LITEWEIGHT CAR MADE FOR STRAIGHT LINE DRAG RACING AND CAN BE BROKEN IF RUN INTO SOLID OBJECTS AT HIGH SPEED. YOU WILL NEED

More information

TOOLS NEEDED TO BUILD THIS KIT

TOOLS NEEDED TO BUILD THIS KIT TOOLS TOOLS NEEDED TO BUILD THIS KIT 1. ALLEN WRENCHES A..050" B. 1/16" C. 5/64" D. 3/32" E. 2.5mm 2. NUT DRIVERS A. 3/16" B. 1/4" C. 11/32" 3. MISC. TOOLS A. NEEDLE NOSE PLIERS B. THREAD LOCKING COMPOUND

More information

TITAN CATALOG 2013 HEX WRENCH & TOOLS RACING EQUIPMENT

TITAN CATALOG 2013 HEX WRENCH & TOOLS RACING EQUIPMENT HEX WRENCH & TOOLS 1 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 11015 11020 11320

More information

Manufactured By: CustomWorks RC Products LLC 760-B Crosspoint Drive Denver, NC #0928 ENFORCER GSX2 RACING KIT

Manufactured By: CustomWorks RC Products LLC 760-B Crosspoint Drive Denver, NC #0928 ENFORCER GSX2 RACING KIT #0928 ENFORCER GSX2 RACING KIT Manufactured By: CustomWorks RC Products LLC 760-B Crosspoint Drive Denver, NC 28037 www.customworksrc.com REQUIRED READING.........UNDERSTAND THIS MANUAL! Thank You and

More information

DRIVE AXLE Volvo 960 DESCRIPTION & OPERATION AXLE IDENTIFICATION DRIVE AXLES Volvo Differentials & Axle Shafts

DRIVE AXLE Volvo 960 DESCRIPTION & OPERATION AXLE IDENTIFICATION DRIVE AXLES Volvo Differentials & Axle Shafts DRIVE AXLE 1994 Volvo 960 1994 DRIVE AXLES Volvo Differentials & Axle Shafts 960 DESCRIPTION & OPERATION All 960 station wagon models use type 1041 rear axle assembly. All 960 4-door models use type 1045

More information

# M18T KIT ONLY # M18T KIT INCLUDING POWER PACK PRO

# M18T KIT ONLY # M18T KIT INCLUDING POWER PACK PRO T includes: Main features: The all-new XRAY T is truly the first micro truck that is capable of transforming from a racer to a monster truck. Imagine, a lightweight high performance 4x4 racer that can

More information

$1.00 FOR THE TQIO/RCIO

$1.00 FOR THE TQIO/RCIO $1.00 FOR THE TQIO/RCIO m mm HDBBYSHOP Champion Jay Halsey has an impressive track record. One of Jay's advantages is a whisper smooth tranny thanks to his dad, Jim. Now you can build a Halsey transmission!

More information

Global West Suspension 655 South Lincoln Ave San Bernardino Ca Phone Fax Web address globalwest.

Global West Suspension 655 South Lincoln Ave San Bernardino Ca Phone Fax Web address globalwest. Global West Suspension 655 South Lincoln Ave San Bernardino Ca. 92408 Phone 877-470-2975 Fax 909-890-0703 Web address globalwest.net Mustang coilover instruction sheets for 64-66 Kit includes the following

More information

1:8 SCALE CATALOG 1:8 GAS KITS RC500 FRONT END BODY ACCESSORIES

1:8 SCALE CATALOG 1:8 GAS KITS RC500 FRONT END BODY ACCESSORIES 1:8 SCALE CATALOG Stock is extremely limited. Parts listing as of 7/2001. Sale prices apply to orders direct from Associated only. Items available while supplies last. Items marked Not available or are

More information

Installation Instructions Mustang Level 2 Coilover. Part # Mustang Level 2 CoilOver System.

Installation Instructions Mustang Level 2 Coilover. Part # Mustang Level 2 CoilOver System. Part # 22020-979-989 Mustang Level 2 CoilOver System Front Components: 2230 Front CoilOver Strut Recommended Tools Rear Components: 2260 Rear Coilover 225899 Rear Lower StrongArms 226699 Rear Upper StrongArms

More information

ABC HOBBY ORIGINAL RADIO CONTROL CAR

ABC HOBBY ORIGINAL RADIO CONTROL CAR ABC HOBBY ORIGINAL RADIO CONTROL CAR Instruction Manual Study the instructions thoroughly before assembly. FRONT WHEEL DRIVE NEW STYLE STRUT SUSPENSION BATHTUB CHASSIS 4 BEVEL GEAR DIFFERENTIAL FULL ADJUSTABLE

More information

Calandra Racing Concepts

Calandra Racing Concepts Calandra Racing Concepts Carpet Knifeä Version 3 Assembly and Setup Manual Congratulations! You now own the best 1/12th scale car on the market today, the Carpet Knifeä Version 3. This completely new car

More information

1/10 LUXURY TOURING CAR

1/10 LUXURY TOURING CAR 1/10 LUXURY TOURING CAR TECHNOLOGY XRAY sets new standards for chassis and car set-up and adjustment Using one chassis and one top deck, you can set up and adjust the new XRAY T2 for almost all different

More information

... REQUIRED READING...

... REQUIRED READING... REQUIRED READING.........UNDERSTAND THIS MANUAL! Thank You and Congratulations on purchasing the DOMINATOR! Within this kit you will find a race winning car with over 25 years worth of CUSTOM WORKS design

More information

INSTALLATION GUIDE Bolt-On Drag-Race Strut Clip Chevy II

INSTALLATION GUIDE Bolt-On Drag-Race Strut Clip Chevy II INSTALLATION GUIDE 7702 Bolt-On Drag-Race Strut Clip 1962-67 Chevy II Description: STRUT CLIP 4130 BOLT ON 62-67 CHEVY II, INCLUDES 4130 ROUND TUBE FRAME CLIP, DOUBLE-ADJUSTABLE STRUTS, ADJUSTABLE-HEIGHT

More information

RJS2001 PRO STOCK KIT LESS ELECTRICS

RJS2001 PRO STOCK KIT LESS ELECTRICS RJS2001 PRO STOCK KIT LESS ELECTRICS THANKS FOR BUYING RJ SPEED S PRO STOCK DRAG KIT. IT IS MADE FOR STRAIGHT LINE DRAG RACING AND CAN BE BROKEN IF RUN INTO SOLID OBJECTS REPEATEDLY AT HIGH SPEED. IT REQUIRES

More information

... REQUIRED READING...

... REQUIRED READING... REQUIRED READING.........UNDERSTAND THIS MANUAL! Thank You and Congratulations on purchasing the OUTLAW! Within this kit you will find a race winning car with over 21 years worth of CUSTOM WORKS design

More information

- 3 -

- 3 - - 2 - - 3 - - 4 - - 5 - - 6 - - 7 - - 8 - - 9 - - 10 - - 11 - - 12 - - 13 - - 14 - - 15 - - 16 - - 17 - - 18 - - 19 - - 20 - - 21 - - 22 - 1/8th Scale Electric 4WD GT Car MGT7 ECO Parts List E2103 FRONT

More information

2030 OUTLAW SPRINTER HARDWARE I.D. BUTTON HD. CAP SCREW BAG H1 CHASSIS KIT BAG H3 HARDWARE BAG L2 REAR AXLE PARTS BAG L4 FRONT TIRES

2030 OUTLAW SPRINTER HARDWARE I.D. BUTTON HD. CAP SCREW BAG H1 CHASSIS KIT BAG H3 HARDWARE BAG L2 REAR AXLE PARTS BAG L4 FRONT TIRES THANKS FOR BUYING THE RJ SPEED OUTLAW SPRINTER KIT. IT IS COMPLETE LESS ELECTRICS, AND MADE FOR CARPET OR PAVEMENT RACING. IT REQUIRES A 540 OR 550 SIZE MOTOR, 4 OR 6 CELL BATTERY PACK, TWO CHANNEL RADIO

More information

BIND ST-TRIM TH-TRIM ST-D/R

BIND ST-TRIM TH-TRIM ST-D/R 4 4 4 4 BIND ST-TRIM TH-TRIM ST-D/R 1. Put the battery in the car. 2. Install the battery. 3. Turn on the transmitter. Connect firmly. 4. Turn on the electronic speed controller. ON OFF AX80084 UV Joint

More information

NOTE: Using hot modified motors exceed the capacity of the electronic speed control and voids any warranty.

NOTE: Using hot modified motors exceed the capacity of the electronic speed control and voids any warranty. OWNER'S MANUAL NOTE: Using hot modified motors exceed the capacity of the electronic speed control and voids any warranty. Carefully read through all instructions to familiarize yourself with the parts,

More information

INFINITY 1/8 ONROAD KIT SPARE & OPTIONAL PARTS FRONT BODY MOUNT PLATE FRONT SUSPENSION ARM REAR UPPER ARM HOLDER SET SERVO SAVER SET FRONT UPRIGHT

INFINITY 1/8 ONROAD KIT SPARE & OPTIONAL PARTS FRONT BODY MOUNT PLATE FRONT SUSPENSION ARM REAR UPPER ARM HOLDER SET SERVO SAVER SET FRONT UPRIGHT Tabella 1 Code CM-00001 Code R0001 R0002 R0003 R0004 R0005 R0006 R0007 R0008 R0009 R0010 R0011 R0012 R0013 R0014 R0015 R0016 R0017 R0018 R0019 R0020 R0021 R0022 R0023 R0024 R0025 R0026 R0027 R0028 R0029

More information

... REQUIRED READING...

... REQUIRED READING... REQUIRED READING.........UNDERSTAND THIS MANUAL! Thank You and Congratulations on purchasing the OUTLAW! Within this kit you will find a race winning car with over 21 years worth of CUSTOM WORKS design

More information

#0923 ENFORCER GBX3 RACING KIT. Manufactured By: 760-B Crosspoint Drive Denver, NC

#0923 ENFORCER GBX3 RACING KIT. Manufactured By: 760-B Crosspoint Drive Denver, NC #0923 ENFORCER GBX3 RACING KIT Manufactured By: 760-B Crosspoint Drive Denver, NC 28037 www.customworksrc.com REQUIRED READING.........UNDERSTAND THIS MANUAL! Thank You and Congratulations on purchasing

More information

Installation Instructions Mustang Air Suspension. Part # Mustang Air Suspension System.

Installation Instructions Mustang Air Suspension. Part # Mustang Air Suspension System. Part # 12120298-1979-1989 Mustang Air Suspension System Recommended Tools Front Components: 12122401 Front ShockWave Strut Rear Components: 12125401 RearShockWave 12125899 Rear Lower StrongArms 12126699

More information

#0710 ELECTRIC ROCKET KIT

#0710 ELECTRIC ROCKET KIT #0710 ELECTRIC ROCKET KIT Manufactured By: 760-B Crosspoint Drive Denver, NC 28037 www.customworksrc.com REQUIRED READING.........UNDERSTAND THIS MANUAL! Thank You and Congratulations on purchasing the

More information

RB5 MID CUSTOM SPECIAL INSTRUCTIONS MANUAL

RB5 MID CUSTOM SPECIAL INSTRUCTIONS MANUAL RB5 MID CUSTOM SPECIAL INSTRUCTIONS MANUAL INTRODUCTION This manual is intended to the few people who were lucky enough to get their hands on a Mid Custom Special conversion for the Kyosho RB5. Due to

More information

Assembly Diagrams-1 22 Shock Assembly Shock Lower Mount Ball Shock Bottom Mount 3. Shock Spring Retainer

Assembly Diagrams-1 22 Shock Assembly Shock Lower Mount Ball Shock Bottom Mount 3. Shock Spring Retainer Assembly Diagrams-1 Shock Assembly 3 4 5 7 8 9 10 11 13 15 1 1 14 1. Shock Lower Mount Ball 4.8. Shock Bottom Mount 3. Shock Spring Retainer(bottom) 4. Shock Spring 5. Shock Body Bush. Shock Seal(small)

More information

Caution. Electronic Speed Controller Instructions. Needle Nose Pliers Awl RCE3003 HD Grease. Fusion Tire Glue. RCE3004 Super Diff Lube

Caution. Electronic Speed Controller Instructions. Needle Nose Pliers Awl RCE3003 HD Grease. Fusion Tire Glue. RCE3004 Super Diff Lube Caution Please read the following manual closely and familiarize yourself with its contents before operating the model. Keep the manual in a safe place for future reference for repairs, part numbers and

More information

#0711 ROCKET PRO-COMP RACING KIT. Manufactured By: 760-B Crosspoint Drive Denver, NC

#0711 ROCKET PRO-COMP RACING KIT. Manufactured By: 760-B Crosspoint Drive Denver, NC #0711 ROCKET PRO-COMP RACING KIT Manufactured By: 760-B Crosspoint Drive Denver, NC 28037 www.customworksrc.com REQUIRED READING.........UNDERSTAND THIS MANUAL! Thank You and Congratulations on purchasing

More information

BAG F STEP F-01 STEP F-02 STEP F-03. Front and Rear Clip Installation

BAG F STEP F-01 STEP F-02 STEP F-03. Front and Rear Clip Installation q STEP F-01 BAG F Front and Rear Clip Installation The Servo Link installed in Step B-03 was set to an approximate length. The correct length will vary depending on the type of servo used, the radio settings,

More information