OPERATES AT UP TO 16MPa, DEPENDING ON FREQUENCY OF PRESSURE SUPPLY

Transcription

1 OPAT DESIGN HYDRAULI YLINDER HQS Series OPERATES AT UP TO Pa, DEPENDING ON FREQUENY OF PRESSURE SUPPLY ALUINU BODY, OPAT DESIGN HYDRAULI YLINDERS IN PURSUIT OF OST PERFORANE OPLETELY OPATIBLE WITH 0S- AND 0S- IN OUTER SIZE AND INSTALLATION DIENSION ALLOWS OST-EFFETIVE SELETION DEPENDING ON FREQUENY OF OPERATION AND OPERAT- ING PRESSURE ROD GLAND ONSTRUTED OF SPEIAL OPPER ALLOY FOR IPROVED WEAR RESISTANE ONFORS TO JIS B37. FATIGUE TEST LASSIFIATION A AT. A -59

2 HQS Series OPERATES AT Pa BY SELETING OPERATING PRESSURE AND USE FREQUENY OPAT DESIGN HYDRAULI YLINDER IN INFINITE PURSUIT OF OST PERFORANE WE PRESENT RELIABILITY Rod Gland (Special copper alloy) ALUINU BODY, OPAT DESIGN HYDRAULI YLINDER onforms to JIS B37-. Fatigue test classification A TYPES OF BORE SIZE, mm, 5mm, 3mm, 40mm, 50mm, 3mm, 0mm and 0mm f,,,,,, f0, and f0 ROD GLAND ONSTRUTED OF SPEIAL OPPER ALLOY Improves wear resistance. NEW DESIGN SWITH BRINGS AINTAINABILITY OON TO AND USABLE FOR ALL TIE ROD END TYPE SWITH SET YLINDERS Switch can be installed either on the right or left. Switch slides freely. ord can be extended to the rear or to the top. Switch conforming to E mark is available. Piston rod (arbon steel for machine structural use/ Hard chromium plated) ompatible with single rod type and double rod type Double acting single rod HQS HQSW Double acting double rod HQSR HQSWR Body (Aluminum alloy) Switch For rod end specifications, male and female thread types are available as well as various special end types. Female type ale type ontact switch, non contact switch, and cutting oil of resistant types are also available as standard. General purpose type NOINAL PRESSURE DIAGRA OF HQS Nominal pressure (Pa) 4 How to view the diagram Testing procedure utting fluid proof type Allowable range Frequency of Pressure Supply,000 times Special and type ylinder bore f,,,, ylinder bore, f0, f0 Frequency of pressure supplied to the cylinder is taken along X-axis. (Horizontal) ove up vertically from the frequency, and the pressure where the line crosses the limit line of each bore size indicates the pressure (nominal pressure) at which the cylinder can be used up to the corresponding frequency of pressure supply. (Rupture probability %) In calculating the nominal pressure, fatigue test is carried out with reference to Guideline for selecting and using hydraulic cylinder, Annex Strength testing procedure of hydraulic cylinder of JFPS4: 0 (Japan Fluid Power Industrial Association Standard). In concrete, pressure is applied to several tens of supply cylinders repeatedly, the frequency of rupture is measured and processed statistically to obtain the nominal pressure. How to determine the nominal pressure Fatigue life is determined by material fatigue test described in testing procedure, and the value obtained by processing such data statistically. Life distribution is obtained from material fatigue test data, of which the value of rupture probability % is used for base of nominal pressure diagram. [Note] No point of 0% exists in terms of statistical method. Nominal pressure Rupture probability P=% P S-N curve corresponding to rupture probability P 4 P=50% Life analysis 5 Frequency of pressure supply Wide selection of support hardware SD, FA, FB, and LD type SD type P FA type HQSD HQSWD HQSRD HQSWRD Universal type and cutting oil resistant specifications have the same dimension. Installation dimensions are the same for both standard type and switch set type. HQSR HQSRD HQSWR HQSWRD utting fluid proof type Packing of dust wiper dedicated to cutting oil resistant type is available for cutting oil resistant type. LD type Stroke 5 to 0 mm (depends on bore)

3 3 HQS ompact Design Hydraulic ylinder OPERATES AT UP TO Pa, DEPENDING ON FREQUENY OF PRESSURE SUPPLY Wide selection of models are available of cylinder bore f to f0. Light-weight, compact design hydraulic cylinder with bodies constructed of special aluminum alloy. ost-effective selection is available based on frequency of operation and operating pressure. Aluminum body, compact design hydraulic cylinder in pursuit of cost performance. Rod gland constructed of special copper alloy for improved wear resistance. Standard Specifications Terminologies Types Nominal pressure (According to nominal pressure diagram) Proof test pressure inimum working pressure Operating speed range Temperature range (Ambient temperature and oil temperature) Structure of cushioning Adaptable working oil Tolerance of thread Tolerance of stroke ounting type Rod end thread Suitable switche for switch set Specifications of General Purpose HQSR: (f, ) T type ( - f0) AX AZ type WR WS type utting Fluid Proof Types f,,,, Pa (Fatigue endurance frequency 5 ) Pa (Fatigue endurance frequency 7 ), f0, f0 Pa (Fatigue endurance frequency 3 5 ) Pa (Fatigue endurance frequency 7 ) Pa 0.3Pa - 0mm/s Standard type Switch set AX AZ types T type WR WS types (at non-freezing condition) None Petroleum-based fluid (For other working oil, refer to the table of working oil adaptability) JIS H/g 0-0.mm SD, LD, FA, FB Female and male thread HQSWR: WR WS type Nominal pressure Operating pressure which guarantees performance under specified condition. Specified condition means our fatigue test with reference to Guideline for selecting and using hydraulic cylinder, Annex Strength testing procedure of hydraulic cylinder, JFPS 4:0 (Japan Fluid Power Industrial Association Standard) Proof test pressure Static pressure used for inspection which does not cause abnormality when held for specified time, and does not deteriorate cylinder performance when returned to the atmospheric pressure. inimum working pressure The minimum pressure that the cylinder placed horizontally without a load can work. Notes) This cylinder is not equipped with an air bleeder. Since lateral load (eccentric load) cannot be applied to the piston rod, carefully adjust it after rod end attachment. Double acting single-rod Double acting double-rod Standard type (HQS HQSW) Switch set (HQSR HQSWR) ylinder dimensions are all the same for both general purpose type and cutting fluid proof type. Standard type (HQSD HQSWD) Switch set (HQSRD HQSWRD)

4 ompact Design Hydraulic ylinder HQS 4 Lines Unit: mm Structure Type ounting Type f f0 f0 General purpose type Double Acting Single Rod Double Acting Double Rod Standard type HQS Switch set HQSR Standard type HQSD Switch set HQSRD SD LD FA FB SD LD FA FB SD LD FA SD LD FA utting fluid proof type Double Acting Single Rod Double Acting Double Rod Standard type HQSW Switch set HQSWR Standard type HQSWD Switch set HQSWRD SD LD FA FB SD LD FA FB SD LD FA SD LD FA Notes) Specify switch set type as above when use switch on cylinder. Switch can not use on Standard type. Nominal pressure diagram Pressure (Pa) ylinder bore f,,,, ylinder bore, f0, f0 4 Allowable range How to read the diagram Frequency of pressure supplied to the cylinder is taken along X-axis. ove up vertically from the frequency, and the pressure where the line crosses the limit line of each bore indicates the pressure (nominal pressure) at which the cylinder can be used up to the corresponding frequency of pressure supply. (Rupture probability %) Frequency of pressure supply,000 times

5 5 HQS ompact Design Hydraulic ylinder General purpose type ( f - f0) Series Packing material Dotted lines for types and symbols are not written when unnecessary. ounting type3 ylinder bore4 ushion type5 Stroke Thread type7 Port specification Switch code9 Switch quantity!0 Standard type HQS SD 40 N 50 T G L V Lock nut! Semi-standard components Air vent! Switch set HQSR SD 40 N 50 T G AH L V Double acting single-rod HQS : Standard type HQSR : Switch set None V Without air vent (Standard) With air vent (ade-to-order: bore 3mm to 0mm) Double acting double-rod HQSD HQSRD : Standard type : Switch set c Fluoric rubber n Hydrogenated nitrile rubber ylinder bore (mm) f f0 f0 Without cushion ylinder stroke (mm) Note) When the switch is retrofitted to the standard type, the switch does not work. Adaptability of Working Oil to Packing aterial Packing aterial cfluoric rubber nhydrogenated nitrile rubber Note) The seal of bore size mm & 5mm is only Nitrile rubber for high temperature. Petroleumbased fluid SD LD FA FB SD type, basic type Foot type Head flange mounting End cap flange mounting Adaptable Working Oil Water-glycol fluid Phosphoric ester fluid W/O Water in oil fluid O/W Oil in water fluid Notes). The and - marked items are applicable, while the - marked items are inapplicable.. The - marked items are the recommended packing materials in case of giving the first priority to abrasion resistance. T None G Switch quantity ( or ) Rc thread G thread ( - f0) Note) G thread is only for SD ounting. L with one lock nut Note) Available only for male thread type Additional order is required when or more lock nuts are necessary. Switch code Note) Select applicable switches out of the Switch List.! Notes on order for switch set If a switch is unnecessary, enter the switch symbol o and the switch quantity!0 of 0. When ordering a switch set, switches are not mounted to cylinders at delivery. Female thread (no code for the standard type) ale thread Note) Double-rod and male thread means both sides are male thread as standard. Specification of Air Vent (Option) The air vents are laid on the port surface and located symmetrical position to the port. Set screw (Exclusive use for air vent) Steel ball (Figure) -Air vent -Port (Structure): Single-rod, Double-rod SD/LD/FA/FB type Location of air vent on the same surface as piping port (Option)

6 ompact Design Hydraulic ylinder HQS utting fluid proof type ( - f0) Series ounting type3 Packing material Dotted lines for types and symbols are not written when unnecessary. Semi-standard components ylinder bore4 ushion type5 Stroke Thread type7 Port specification Switch code9 Switch quantity!0 Standard type HQSW SD 40 N 50 T G L V Lock nut! Air vent! Switch set HQSWR SD 40 N 50 T G 5 L V Double acting single-rod HQSW HQSWR : Standard type : Switch set Double acting double-rod HQSWD HQSWRD : Standard type : Switch set n Hydrogenated nitrile rubber ylinder bore (mm) f0 f0 Note) size mm & 5mm are not available. 5 5F F F F WR55 (cord extended from the rear, with 5 m cord) WR535 (cord extended from the top, with 5 m cord) WR55F (cord extended from the rear, with 5 m cord/flex tube attached) WR535F (cord extended from the top, with 5 m cord/flex tube attached) WS35 (cord extended from the rear, with 5 m cord) WS5 (cord extended from the top, with 5 m cord) WS35F (cord extended from the rear, with 5 m cord/flex tube attached) WS5F (cord extended from the top, with 5 m cord/flex tube attached) Note) For explanations for models other than the above, refer to the general purpose type models. Note) For explanations for models other than the above, refer to the general purpose type models. utting Fluid Proof Type/Adaptability of utting Fluid to Packing aterial Packing aterial Non-water Soluble utting Oil Water Soluble utting Oil Type Type nhydrogenated nitrile rubber : applicable : inapplicable How to order G screw piping port (only for SD type) Please specify the model as following. ex. HQS SD3N G G screw piping port How to order only lock nut d Dimension Table Part odel d B h f LNH-F-H LNH-F-H h B f0 f0 LNH-F-H LNH-F-H LNH-F-H LNH-F-H LNH-39F-H LNH-4F-H

7 7 HQS ompact Design Hydraulic ylinder Switch List ( of f ) ind Switch Symbol Load Voltage Range Load urrent Range Protective ircuit Indicating Lamp Wiring ethod ord Length Applicable With ontact With no ontact UA T0H UB T0H3 U T5H UD T5H3 UE T0V UF T0V3 UG T5V UH T5V3 UJ TH U TH3 UL TYH U TYH3 UN T3H UP T3H3 UQ TV UR TV3 US TYV UT TYV3 UU T3V UV T3V3 D V A0V D5 V A0V D V A0V D5 V A0V D - V DV or less D - V DV or less D:5-50mA A:7 - ma D:50mA or less A:mA or less D:5-50mA A:7 - ma D:50mA or less A:mA or less 5 - ma or less 0mA or less 5 - ma or less 0mA or less aximum Open/ lose apacity D:.W A:VA Voltage D - V Voltage D - V None Present LED (Red light lights up during ON) LED (Red light lights up during ON) None LED (Red light lights up during ON) LED (Red light lights up during ON) LED (-lamp type in red/green) LED (Red light lights up during ON) 0.mm -core, outside diameter, f3.4mm Rear wiring 0.mm -core, outside diameter, f3.4mm Upper wiring 0.mm -core, outside diameter, f3.4mm Rear wiring 0.3mm -core, outside diameter, f4.mm Rear wiring 0.mm 3-core, outside diameter, f3.4mm Rear wiring 0.mm -core, outside diameter, f3.4mm Rear wiring 0.3mm -core, outside diameter, f4.mm Rear wiring 0.mm 3-core, outside diameter, f3.4mm Rear wiring m 3m m 3m m 3m m 3m m 3m m 3m m 3m m 3m m 3m m 3m Load Device Small relay Programmable ontroller Small relay Programmable ontroller Notes) For the switch without a protective circuit, be sure to provide the protective circuit (S-0) with load devices when using induction load devices (relays). For 0 VA type, contact us. None LED (-lamp type in red/green) LED (Red light lights up during ON) General purpose type -lamp type -lamp type Switch ounting inimum Possible Stroke f f0 f0 AX and AZ types 5 T type 5 With A Switch WR type 5 WS type Note) When attaching two switches of the WR or WS type, they cannot be attached to the same surface. If you would like to mount two switches to mm stroke cylinder, please. AX and AZ types With Two Switches T type WR type WS type 5

8 ompact Design Hydraulic ylinder HQS Switch List (For bore 3 mm to 0 mm) General purpose type AX type (cord rear wiring) AZ type (cord upper wiring) 5-40mA - 70mA 5-40mA - 70mA utting fluid proof type WR WS type switch ord rear wiring ord upper wiring aximum Open/ lose apacity ind Switch Symbol Load Voltage Range Load urrent Range Protective ircuit Indicating Lamp Wiring ethod ord Length Load Applicable Device AF AX.5m None LED AG AX5 D:5 - V D:5-40mA 5m D:.5W (Red light lights 0.3 mm -core, outside AH AX A:5 - V A:5 - ma diameter, f4 mm.5m A:VA Present up during ON) Rear wiring AJ AX5 5m D:V or less D:40V or less AE AX5 A:V or less A:V or less None None 5m A AXA A:5 - V 5 - ma VA LED (Red light 4-pin connector, type 0.5m Present Rear wiring AL AXB D:5 - V 5-40mA.5W lights up during ON) 0.5m 5 WR55 D:5-50V D:3-40mA 0.3 mm -core, outside D:.5W LED (Red light 5m None diameter, f4 mm Small relay, 5F WR55F A:5 - V A:3 - ma A:VA lights up during ON) Rear wiring 5m programmable AP AZ.5m controller None LED AR AZ5 D:5 - V D:5-40mA 5m (Red light lights 0.3 mm -core, outside AS AZ A:5 - V A:5 - ma D:.5W diameter, f4 mm.5m A:VA Present up during ON) Upper wiring AT AZ5 5m D:V or less D:40V or less AN AZ5 A:V or less A:V or less None None 5m AU AZA A:5 - V 5 - ma VA LED (Red light 4-pin connector, cord 0.5m Present extended from the top AW AZB D:5 - V 5-40mA.5W lights up during ON) 0.5m D:5-50V D:3-40mA D:.5W LED (Red light 0.3 mm -core, outside 5m None diameter, f4 mm A:5 - V A:3 - ma A:VA lights up during ON) Upper wiring 5m ontact No ontact No ontact (E coformed) WR535 F WR535F BE AX BF AX5 D:5 - V E AX F AX5 WS35 D: - V F WS35F B AZ BN AZ5 D:5 - V AZ N AZ5 WS5 D: - V F WS5F T AXE U AX5E V AXBE D:5 - V W AZE X AZ5E Y AZBE WR55 WS35 Present Present Present Present 5-40mA Present LED (Red light lights up during ON) LED (-lamp type in red/green) LED (-lamp type in red/green) LED (Red light lights up during ON) LED (-lamp type in red/green) LED (-lamp type in red/green) LED (-lamp type in red/green) 0.3 mm -core, outside diameter, f4 mm Rear wiring 0.3 mm -core, outside diameter, f4 mm Upper wiring 0.3 mm -core, outside diameter, f4 mm Rear wiring 4-pin connector, type Rear wiring 0.3 mm -core, outside diameter, f4 mm Upper wiring 4-pin connector, cord extended from the top.5m 5m.5m 5m 5m 5m.5m 5m.5m 5m 5m 5m.5m 5m 0.5m.5m 5m 0.5m Small relay, programmable controller Notes) For the switches without a protective circuit, be sure to provide the protective circuit (S-0) with load devices when using induction load devices (relay, etc.). For the handling of switches, be sure to refer to the switch specifications in the end of 70/40H- series catalogue. The WR and WS type switches are cutting fluid proof type. For the 0 V A type, contact us. For the switch symbol o, pay attention to the points below when ordering the cutting fluid proof type switches, WR and WS types. 5 5F F F F WR55 WR535 WS35 WS5 WR55F WR535F WS35F WS5F The switch and straight box connector (F-SB) are combined [the flex tube (F-05: 4. m) is required]. The flex tube (F-05: 4. m) is attached to the switch and straight box connector (F-SB). WR535 WS5 Switch body Straight box connector: F-SB Flex tube: F-05

9 HQS ompact Design Hydraulic ylinder : Standard manufacturing range, : Range available for manufacturing for order (Delivery date depends on bore and stroke. ontact us for detail.) For the minimum stroke of the switch set, refer to the Switch ounting inimum Possible Stroke table. (P.7) Note ) Size of 5mm stroke cylinder body of bore mm and 5mm is same dimension as body of mm stroke Structure ylinder Stroke (mm) Type ale Thread Type Double Acting Single-rod Standard type HQS f f0 f0 f f0 f0 f f0 f0 f f0 f0 f0 f0 f0 f0 f0 f0 f0 f Switch set HQSR Standard type HQSD Switch set HQSRD Standard type HQSW Switch set HQSWR Standard type HQSWD Switch set HQSWRD Double Acting Double-rod Double Acting Single-rod Standard stroke fabrication range 9 Double Acting Double-rod General purpose type utting fluid proof type

10 ompact Design Hydraulic ylinder HQS Weight Table/General Purpose and utting Fluid Proof Types Structure Double Acting Single-rod Double Acting Double-rod Type Standard type HQS HQSW Switch set HQSR HQSWR Standard type HQSD HQSWD Switch set HQSRD HQSWRD f f0 f0 f f0 f0 f f0 f0 f f0 f ylinder Stroke (mm) ounting accessories Separate additional weight Foot type Flange type (LD) (FA, FB) flange joint ( type joint) Unit: kg Added male thread weight Switch Added Weight Table Unit: kg ord length.5m AX AZ Type ord length 5m onnector type T0 T T3 T5 Type ord length m ord length 3m TY Type ord length m ord length 3m WR WS Type Piston Pressurized Area Table (mm) f f0 f0 Rod Diameter (mm) f f4 f f f f3 f45 f5 Unit: mm Double Acting Single-rod Double Acting Double-rod Push side Pull side Push side Pull side Formula F = A P β(n) F: ylinder force (N) A: Piston pressurized area (mm ) P: Applied pressure (Pa) β: Load rate alculation example Double acting single-rod, bore of, applied pressure of Pa, load rate of 0. Push side cylinder force (N) = = 05 (N) Pull side cylinder force (N) = 7 0. = 700 (N)

11 HQS ompact Design Hydraulic ylinder Double Acting Single-rod/Standard Type Unit: mm SD

12 Unit: mm ompact Design Hydraulic ylinder Double Acting Single-rod/Standard Type HQS Dimension Table Symbol A AE BT D DE E EE FB FF FG Female thread ale thread L f 5(5) Rc/ f5.5 f () Rc/ f5.5 f (40) f7. Rc/4 f. G/ f (45). 7 9 f7. 70 Rc/4 f9 G/ f4.5 35(50). f.5 0 Rc/4 f G/4 f (0) 3 9 f.5 94 Rc/4 f4 G/4 f f0 0(0) f.5 4 Rc3/ f G/4 f f0 75(95) Rc3/ f G3/ f Symbol LF LL N Rc thread G thread PJ Rc thread G thread PL Rc thread G thread TV WF Y Rc thread G thread f 5 43 f f f f f f f f f0 9 f Notes) When you use the cylinder with lock nut, we recommend you change A dimension for parenthetic one. (made-to-order.) The lock nut needs to be ordered separately. (Refer to page of how to order.) For 5 stroke type of bore mm and 5 mm, dimension is the same as for stroke type. mm and 5mm bore size of utting Fluid Proof Type are not available. Allowance of is f.

13 HQS ompact Design Hydraulic ylinder Double Acting Single-rod/Standard Type Unit: mm ale thread EE A W N N Width across flats D FP PJ+ Stroke P E depth L LF+Stroke EH LH ST Width across flats D 4-SB TS US W SU XS LL+Stroke SS+Stroke ZB+Stroke SU SY

14 Unit: mm ompact Design Hydraulic ylinder Double Acting Single-rod/Standard Type HQS 4 Dimension Table Symbol A D E EE EH FP Female thread ale thread L LF LH f 5(5) 44 Rc/ ±0.5 () 50 Rc/ ±0.5 5(40) 7 4 Rc/ ±0.5 (45) Rc/ ±0.5 35(50) 0 Rc/ ±0.5 45(0) 9 94 Rc/ ±0.5 f0 0(0) Rc3/ ±0.5 f0 75(95) 50 3 Rc3/ ±0.5 Symbol LL N PJ P SB SS ST SU SY TS US W XS ZB f 43 f f f f f f f0 7 f f0 9 f Notes) When you use the cylinder with lock nut, we recommend you change A dimension for parenthetic one. (made-to-order.) The lock nut needs to be ordered separately. (Refer to page of how to order.) For 5 stroke type of bore mm and 5 mm, dimension is the same as for stroke type. mm and 5mm bore size of utting Fluid Proof Type are not available. Allowance of is f.

15 5 FA HQS Standard type General purpose type utting fluid proof type Switch set General purpose type utting fluid proof type f HQS FA N Stroke HQSW FA N Stroke HQSR FA N Stroke HQSWR FA N Stroke ompact Design Hydraulic ylinder Double Acting Single-rod/Standard Type ale thread A W T T T T HQS/THQS (f - f0) ( - f0) None : Female thread T : ale thread Switch code Switch code : Female thread T : ale thread EE AD/DATA is available. Switch quantity (f - f0) Switch quantity ( - f0) Unit: mm N N Width across flats D E TV 4-FB Y PJ+Stroke PL FE R 4- depth P TF UF Width across flats D W F LL+Stroke - f0 ale thread A W EE N N Width across flats D E TV 4-FB Y PJ+Stroke PL FE R Width across flats D 4- depth P TF UF W F LL+Stroke See Switch set dimension diagram for installing the switch. It is the same except for switch installing dimension. Switch installing groove is available in 3 positions for bore 0 mm.

16 Unit: mm ompact Design Hydraulic ylinder Double Acting Single-rod/Standard Type HQS Dimension Table Symbol A D E EE F FB FE Female thread ale thread L LL f 5(5) 44 Rc/ f () 50 Rc/ f (40) 7 4 Rc/4 5 f (45) Rc/4 f (50) 0 Rc/4 f (0) 9 94 Rc/4 f f0 0(0) Rc3/ 5 f f0 75(95) 50 3 Rc3/ f Symbol N PJ PL R TF TV UF W Y f 5 0. f f f f f f f0 4 f f0 f Notes) When you use the cylinder with lock nut, we recommend you change A dimension for parenthetic one. (made-to-order.) The lock nut needs to be ordered separately. (Refer to page of how to order.) For 5 stroke type of bore mm and 5 mm, dimension is the same as for stroke type. mm and 5mm bore size of utting Fluid Proof Type are not available. Allowance of is f.

17 HQS ompact Design Hydraulic ylinder Double Acting Single-rod/Standard Type Unit: mm - f0

18 Unit: mm ompact Design Hydraulic ylinder Double Acting Single-rod/Standard Type HQS Dimension Table Symbol A D E EE F FB FE Female thread ale thread L LL f 5(5) 44 Rc/ f () 50 Rc/ f (40) 7 4 Rc/4 5 f (45) Rc/4 f (50) 0 Rc/4 f (0) 9 94 Rc/4 f f0 0(0) Rc3/ 5 f f0 75(95) 50 3 Rc3/ f Symbol N PJ PL R TF TV UF WF Y f 5 0. f f f f f f f0 4 f f0 f Notes) When you use the cylinder with lock nut, we recommend you change A dimension for parenthetic one. (made-to-order.) The lock nut needs to be ordered separately. (Refer to page of how to order.) For 5 stroke type of bore mm and 5 mm, dimension is the same as for stroke type. mm and 5mm bore size of utting Fluid Proof Type are not available. Allowance of is f.

19 9 SD HQS Standard type General purpose type utting fluid proof type Switch set General purpose type utting fluid proof type f ompact Design Hydraulic ylinder Double Acting Double-rod/Standard Type HQSDW SD N Stroke HQSWD SD N Stroke HQSRD SD N Stroke HQSWRD SD N Stroke ale thread A WF T T T T HQS/THQS (f - f0) ( - f0) None : Female thread T : ale thread Switch code Switch code : Female thread T : ale thread EE AD/DATA is available. Unit: mm Switch quantity (f - f0) Switch quantity ( - f0) depth L N N Width across flats D 4-FB holes 4-ounter hole diameter FG, Depth BT depth L Y PJ+Stroke Y V cut machined circle - f0 TV E Width across flats D WF LL+Stroke WF+ Stroke AE G screw port DE FF ale thread A WF EE depth L N N Width across flats D 4-FB holes 4-ounter hole diameter FG, Depth BT depth L Y PJ+Stroke Y V cut machined circle Width across flats D TV E WF LL+Stroke WF+Stroke Face with no V cut machined circle is for mounting. See Switch set dimension diagram for installing the switch. It is the same except for switch installing dimension. Switch installing groove is available in 3 positions for bore 0 mm.

20 Unit: mm ompact Design Hydraulic ylinder Double Acting Double-rod/Standard Type HQS Dimension Table Symbol A AE BT D DE E EE FB FF FG Female thread ale thread L f 5(5) Rc/ f5.5 f () Rc/ f5.5 f (40) f7. Rc/4 f. G/ f (45). 7 9 f7. 70 Rc/4 f9 G/ f4.5 35(50). f.5 0 Rc/4 f G/4 f (0) 3 9 f.5 94 Rc/4 f4 G/4 f f0 0(0) f.5 4 Rc3/ f G/4 f f0 75(95) Rc3/ f G3/ f Symbol LL N Rc thread G thread PJ Rc thread G thread TV WF Y Rc thread G thread f 54 f f f 47 7 f f f3 9 3 f0 95 f f0 f Notes) When you use the cylinder with lock nut, we recommend you change A dimension for parenthetic one. (made-to-order.) The lock nut needs to be ordered separately. (Refer to page of how to order.) For 5 stroke type of bore mm and 5 mm, dimension is the same as for stroke type. mm and 5mm bore size of utting Fluid Proof Type are not available. Allowance of is f.

21 LD HQS Standard type General purpose type utting fluid proof type Switch set General purpose type utting fluid proof type f ompact Design Hydraulic ylinder Double Acting Double-rod/Standard Type HQSDW LD N Stroke HQSWD LD N Stroke HQSRD LD N Stroke HQSWRD LD N Stroke ale thread A W T T T T HQS/THQS (f - f0) ( - f0) None : Female thread T : ale thread Switch code Switch code : Female thread T : ale thread EE AD/DATA is available. Unit: mm Switch quantity (f - f0) Switch quantity ( - f0) depth L N N Width across flats D E depth L FP PJ+ Stroke LG+Stroke FP EH LH ST 4-SB TS US Width across flats D W SU XS LZ+Stroke SV+Stroke ZZ+Stroke SU W+Stroke XS+Stroke - f0 ale thread A W EE depth L N N Width across flats D E depth L FP PJ+Stroke LG+Stroke FP EH LH ST 4-SB TS US Width across flats D W SU XS LZ+Stroke SV+Stroke ZZ+Stroke SU W+Stroke XS+Stroke See Switch set dimension diagram for installing the switch. It is the same except for switch installing dimension. Please be sure to use the Socket Head Screw when install the cylinder to the contact patch. Switch installing groove is available in 3 positions for bore 0 mm.

22 Unit: mm ompact Design Hydraulic ylinder Double Acting Double-rod/Standard Type HQS Dimension Table Symbol A D E EE EH FP Female thread ale thread L LG LH f 5(5) 44 Rc/ ±0.5 () 50 Rc/ ±0.5 5(40) 7 4 Rc/ ±0.5 (45) Rc/ ±0.5 35(50) 0 Rc/ ±0.5 45(0) 9 94 Rc/ ±0.5 f0 0(0) Rc3/ ±0.5 f0 75(95) 50 3 Rc3/ ±0.5 Symbol LZ N PJ SB ST SU SV TS US W XS ZZ f 54 f f f f f f f0 95 f f0 f Notes) When you use the cylinder with lock nut, we recommend you change A dimension for parenthetic one. (made-to-order.) The lock nut needs to be ordered separately. (Refer to page of how to order.) For 5 stroke type of bore mm and 5 mm, dimension is the same as for stroke type. mm and 5mm bore size of utting Fluid Proof Type are not available. Allowance of is f.

23 HQS ompact Design Hydraulic ylinder Double Acting Double-rod/Standard Type Unit: mm f - f0

24 Unit: mm ompact Design Hydraulic ylinder Double Acting Double-rod/Standard Type HQS Dimension Table Symbol A D E EE F FB FE Female thread ale thread L LL f 5(5) 44 Rc/ f () 50 Rc/ f (40) 7 4 Rc/4 5 f (45) Rc/4 f (50) 0 Rc/4 f (0) 9 94 Rc/4 f f0 0(0) Rc3/ 5 f f0 75(95) 50 3 Rc3/ f Symbol N PJ R TF TV UF W WF Y f 5 0. f f f f f f f0 4 f f0 f Notes) When you use the cylinder with lock nut, we recommend you change A dimension for parenthetic one. (made-to-order.) The lock nut needs to be ordered separately. (Refer to page of how to order.) For 5 stroke type of bore mm and 5 mm, dimension is the same as for stroke type. mm and 5mm bore size of utting Fluid Proof Type are not available. Allowance of is f.

25 5 HQS ompact Design Hydraulic ylinder Double Acting Double-rod/Standard Type Unit: mm Switch set General purpose type HQSR(D) ounting type N Stroke T Switch code Switch quantity utting fluid proof type HQSWR(D) ounting type N Stroke T Switch code Switch quantity f Single-rod : Female thread T : ale thread ord extended to rear T type RV ord extended to top T type RV Double-rod UX UX ord extended to rear T type RV ord extended to top T type RV V cut machined circle The side which has no V circular groove on the end surface corresponds to UX. UX UX - f0 Single-rod ord extended to rear AX type RV ord extended to top AZ type RV Type of bore 0 mm has switch groove in three positions. UX UX Double-rod ord extended to rear AX type RV ord extended to top AZ type RV V cut machined circle Type of bore 0 mm has switch groove in three positions. The side which has no V circular groove on the end surface corresponds to UX. UX UX

26 Unit: mm ompact Design Hydraulic ylinder Double Acting Double-rod/Standard Type HQS General purpose type Dimension Table (T AX AZ Type) RV UX UX T0H T5H TH T3H T0V T5V TV T3V TYH TYV AX AZ Single-rod T AX AZ Double-rod T AX AZ Single-rod T AX AZ Double-rod T AX AZ f f f Note) UX dimension is for a guide. See the Switch onitoring inimum Possible Stroke list for detail. Operating Ranges and Differences f f0 f0 ontact No ontact AX AZ T type WR type AX AZ T T3 type TY type WS type Operating range Difference Operating range Difference Operating range Difference Operating range Difference Operating range Difference Operating range Difference Operating range Difference or less or less 3 - or less or less.5 or less or less or less 3 - or less 5 - or less or less or less utting fluid proof type WR WS type switch attachment dimensions ord rear wiring WR55 (contact) WS35 (no contact) RV RY RV Dimension Table RV RY UX UX ord rear wiring ord upper wiring ord rear wiring ord upper wiring WR WS WR WS () 5(5) () (3) 7(7) () 4(33) (3) 9(9) () (35) (37) () () (3) 3(40) f (5) 9(9) 5(43) 9(47) Type of bore 0 mm has mounting groove on three sides. ord upper wiring WR535 (contact) WS5 (no contact) RV RY RV f (33) 35(35) 40(50) 4(5) Note) Set the flex tube so that its bend radius becomes R5 or more. If the bend radius becomes smaller than this value, the cord may be disconnected Numeric within ( ) indicates the dimension of double-rod type. Recessed for the bend radius dimension R5 or more Type of bore 0 mm has mounting groove on three sides. When the switch cannot be attached as shown above, use the other type (cord upper wiring).

27 7 HQS ompact Design Hydraulic ylinder Unit: mm Special specification at the rod end You can easily order following categolized items using the Semi-standard symbols and dimensional parameters. (No need to specify dimensional parameters if you would apply the basic dimensions.) How to order Series odel number Semi-standard symbols Dimensional parameters Parameter and P need to be specified as a pair. ex. A3 DR 3 5 A3, bore:40mm, WF:0mm HQS SD40N50T-X A3 WF-0 D DP A 0. A A - f0 FA=W SD FB=WF Note) Only WF dimension can be changed at A and A3 special rod end shape. If you would like to change other. Special rod end shape A00(T) A5 P Width across flats S A WF WF Basic Dimension Table (Standard Dimensions) Basic Dimension Table A P S WF WF f 5.5 f f f.5 f4 f4 5.5 f 4 f.5 f 9 f 35.5 f f 45.5 f3 3 f3 3 f f f0 f45 7 f f5 50 f0 f5 Dimensions indicated by ark are fixed as our semi-standard. You are requested to consult us if you would like to change fixed dimensions.

28 HQS ompact Design Hydraulic ylinder Unit: mm A A54 A f f0 f0 A A DN P f f4 f f f f3 f45 f5 L S WF 3 7

29 9 HQS ompact Design Hydraulic ylinder Unit: mm Separate flange joint : Only for A rod end style F G 45 4-D3 Reverse face/counter hole diameter D4 depth H A D D J B B E 3 Need additional order for this item. Part No.: RH-Rod Dia. mm. Dimension Table Symbol Parts code A B D D D3 D4 E F G H J f RH- f f3 f.5 f5.5 f f9 RH-4 f f5 f.5 f5.5 f f3 RH- f49 3 f9 f3.5 f. f f34 RH- f f3 f.5 f9 f RH- f f9 f.5 f f RH-3 f77 37 f3 f7 f f f55 f0 RH-45 f0 4.5 f4 f33 f4 f f7 f0 RH-5 f f0 f4 f f f9

30 Unit: mm ompact Design Hydraulic ylinder HQS AX AZ type switch ( - f0) WR WS type bracket set screw s tightening torque: Approximately 0. N m Bracket set screw (4) Bracket (T07) Recess Slide the switch to the desired position.

31 3 HQS ompact Design Hydraulic ylinder Unit: mm Precautions for Use When using the cylinder with the rod push output, tighten the screw(s) to the rod end completely so that no load is applied to the piston rod screw section. Since lateral load (eccentric load) cannot be applied to the piston rod, carefully adjust it after rod end attachment. When tightening the double-acting double rod type s piston rod end thread(s), be sure to use the width across flats of the rod to be tightened. Since the double rod type s piston rod is tightened by screws, be careful not to apply rotational force to the piston rod s both ends. Note) Since the HQS series is not equipped with the air bleeder, perform air-bleeding via the piping section. Use four hexagon socket bolts (JIS B7, strength classification of.9 or more) to install the cylinder. When using mounting bolts, screw the bolt s threads 0% or more into the installation members. The material for the installation members must have strength equal to SS400. When using nuts to tighten the mounting bolts, use steel nuts with a strength classification of or more. (However, DO NOT use type 3 nuts.) When using the mounting bolts to secure the cylinder unit, be sure to use the following standard tightening torque. ylinder ounting Bolt Tightening Torque ylinder f f0 f0 Tightening Torque N m When installing the foot type, use the accompanying key. If this key cannot be used, attach a stopper in front and rear of the cylinder unit. Otherwise, the mounting bolts may be damaged. Overhaul and Reassembly Requirements Set screw (Hexagon wrench) Turning hole ounting Bolt Note) The body contains a copper piece under the set screw. After removing the set screw, use the rod gland s turning hole to remove the rod gland from the cylinder body. Since, when removing the rod end thread s jig, burrs may occur on the rod s width across flats, use a file or other appropriate tools to remove the burrs and then remove the rod gland. The piston rod and piston cannot be disassembled. When reassembling the cylinder, be careful that foreign matters such as dust, filings, and debris do not enter the inside of the cylinder. Under the set screw, a rod gland thread protective copper piece is equipped. First, remove this ball and then tighten the rod gland. After tightening the rod gland, return the seal set s copper piece in place and tighten the set screw. Seal Replacement When overhauling the cylinder, replace all the sealing materials (seals and gaskets) with new ones. General purpose type (HQS, HQSD, HQSR, HQSRD) s piston seal, rod seal, dust wiper, and rod gland O-ring can be replaced. utting fluid proof type (HQSW, HQSWD, HQSWR, HQSWRD) s piston seal, rod seal, rod gland O-ring can be replaced. Wiper-seal of utting Fluid Proof Type is pressed into the rod grand, so rod grand including the Wiper-seal is available as a spare part. Please be careful for not being included wiper-seal in the seal kit. Since the piston and rod have been locked, the piston rod O-ring cannot be replaced. Dimension of turning hole fd depth a PD *General purpose type:bore f~f0 utting fluid proof type:bore ~f0 f f0 f0 a f *utting fluid proof type:bore d PD

32 Sectional drawings / packing list

33 33 HQS Sectional drawings/packing list Double Acting Single-rod/Standard type/hqs f f Switch mounting gutter is available in 3 positions only for bore 0 mm. Double Acting Single-rod/utting Fluid Proof type/hqsw - f

34 Sectional drawings/packing list HQS 34 Parts list No. Name aterial Q ty Body Aluminum alloy Piston Special copper alloy 3 Piston rod Stainless steel (f ) arbon steel for machine structural use ( - f0) Rod gland Special copper alloy 7 agnet holder Special copper alloy (f : For 5 stroke) Stainless steel (f - ) A Set screw hrome molybdenum steel B Steel ball Stainless steel opper piece opper D Piston rod O-ring The piston rod O-ring D cannot be replaced because the piston and rod are tighting.

35 HQS Sectional drawings/packing list Double Acting Single-rod/Switch set/hqsr f f0 Double Acting Single-rod/utting Fluid Proof type/hqswr - f0

36 Sectional drawings/packing list HQS 3 Parts list No. Name aterial Q ty Body Aluminum alloy Piston Special copper alloy 3 Piston rod Stainless steel (f ) arbon steel for machine structural use ( - f0) Rod gland Special copper alloy 7 agnet holder Special copper alloy (f : For 5 stroke) Stainless steel (f - f0) 9 agnet A Set screw hrome molybdenum steel B Steel ball Stainless steel opper piece opper D Piston rod O-ring E Switch The piston rod O-ring D cannot be replaced because the piston and rod are tighting.

37 Packing set Packing set 37 HQS Sectional drawings/packing list Packing list n Hydrogenated nitrile rubber/hqs, HQSR No. Parts name aterial Q ty f Parts code F Piston packing Hydrogenated nitrile rubber NHY- NHY-5 NHY-3 NHY-40 G Rod packing Hydrogenated nitrile rubber UHY- UHY-4 UHR- UHR- H Dust wiper Hydrogenated nitrile rubber LPH- LPH-4 DHS- DHS- I Rod gland O-ring Hydrogenated nitrile rubber S- S-.4 G-5 G-35 Double acting single rod cylinder set RS/PS-0 RS/PS-05 QS/PS-03 QS/PS-040 No. Parts name aterial Q ty Parts code f0 f0 F Piston packing Hydrogenated nitrile rubber NHY-50 NHY-3 NHY-0 NHY-0 G Rod packing Hydrogenated nitrile rubber UHR-A UHR-3 UHR-45 UHR-5 H Dust wiper Hydrogenated nitrile rubber DHS- DHS-3 DHS-45 DHS-5 I Rod gland O-ring Hydrogenated nitrile rubber G-45 G-5 G-75 G-95 Double acting single rod cylinder set QS/PS-050 QS/PS-03 QS/PS-00 QS/PS-0 A copper piece for protecting the threads of the rod gland is included in the packing set. Be careful not to lose it.

38 Packing set Packing set Sectional drawings/packing list HQS 3 Packing list c Fluoric rubber/hqs, HQSR No. F G H I Parts name aterial Q ty Piston packing Fluoric rubber Rod packing Fluoric rubber Dust wiper Fluoric rubber Rod gland O-ring Fluoric rubber Parts code f0 f0 P- P-34 P-44 P-53 P-70 P-90 UHR- UHR- UHR-A UHR-3 UHR-45 UHR-5 DHS- DHS- DHS- DHS-3 DHS-45 DHS-5 G-5 G-35 G-45 G-5 G-75 G-95 Double acting single rod cylinder set QS/PS3-03 QS/PS3-040 QS/PS3-050 QS/PS3-03 QS/PS3-00 QS/PS3-0 The hardness of the O-ring (P G) is Hs90. A copper piece for protecting the threads of the rod gland is included in the packing set. Be careful not to lose it. n utting fluid proof type/hqsw, HQSWR No. F G O I Parts code Parts name aterial Q ty f0 f0 Piston packing Rod packing Dust wiper Rod gland O-ring Hydrogenated nitrile rubber Hydrogenated nitrile rubber anned hydrogenated nitrile rubber Hydrogenated nitrile rubber NHY-3 UHR- (DYL-S) G-5 NHY-40 UHR- (DYL-S) G-35 NHY-50 UHR-A (DYL-S) G-45 NHY-3 UHR-3 (DYL-3S) G-5 NHY-0 UHR-45 (DYL-45S) G-75 NHY-0 UHR-5 (DYL-5) G-95 Double acting single rod cylinder set QSW/PS -03 QSW/PS -040 QSW/PS -050 QSW/PS -03 QSW/PS -00 QSW/PS -0 You could replace it, but we recommend that you change the Rod grand ass y including Dust-Wiper. Because the damage to the grand may lead to the leakage of oil. In this reason, Dust-Wiper isn t included in the seal kit. But you could buy only Dust-Wiper according to your separate order. The dust wipe O is pressed in the rod gland to be incorporated with it, and cannot be replaced singly. When replace together with the rod gland. A copper piece for protecting the threads of the rod gland is included in the packing set. Be careful not to lose it.

39 39 HQS Sectional drawings/packing list Double Acting Double-rod/Standard type/hqsd f f Switch mounting gutter is available in 3 positions only for bore 0 mm. Double Acting Double-rod/utting Fluid Proof type/hqswd - f

40 Sectional drawings/packing list HQS 40 Parts list No. Name aterial Q ty Body Aluminum alloy Piston Special copper alloy 4 Piston rod A Stainless steel (f ) arbon steel for machine structural use ( - f0) 5 Piston rod B Stainless steel (f ) arbon steel for machine structural use () Rod gland Special copper alloy 7 agnet holder Special copper alloy (f : For 5 stroke) Stainless steel (f - ) Split fitting Special copper alloy ( - f0) 0 Set screw hrome molybdenum steel ( - f0) A Set screw hrome molybdenum steel opper piece opper D Piston rod O-ring The piston rod O-ring D cannot be replaced because the piston and rod are tighting.

41 4 HQS Sectional drawings/packing list Double Acting Double-rod/Switch set/hqsrd f Note) Rod structure for - f0 is with one piece. Switch mounting gutter is available in 3 positions for bore 0 mm. Type of bore 0 mm is equipped with yoke plate. Double Acting Double-rod/utting Fluid Proof type/hqswrd - f

42 Sectional drawings/packing list HQS 4 Parts list No. Name aterial Q ty Body Aluminum alloy Piston Special copper alloy 4 Piston rod A Stainless steel (f ) arbon steel for machine structural use ( - f0) 5 Piston rod B Stainless steel (f ) arbon steel for machine structural use () Rod gland Special copper alloy 7 agnet holder Special copper alloy (f : For 5mm stroke) Stainless steel (f - f0) Split fitting Special copper alloy ( - f0) 9 agnet 0 Set screw hrome molybdenum steel ( - f0) A Set screw hrome molybdenum steel opper piece opper D Piston rod O-ring E Switch The piston rod O-ring D cannot be replaced because the piston and rod are tighting.

43 Packing set Packing set 43 HQS Sectional drawings/packing list Packing list n Hydrogenated nitrile rubber/hqsd, HQSRD No. Parts name aterial Q ty f Parts code F Piston packing Hydrogenated nitrile rubber NHY- NHY-5 NHY-3 NHY-40 G Rod packing Hydrogenated nitrile rubber UHY- UHY-4 UHR- UHR- H Dust wiper Hydrogenated nitrile rubber LPH- LPH-4 DHS- DHS- I Rod gland O-ring Hydrogenated nitrile rubber S- S-.4 G-5 G-35 Double acting double rod cylinder set RSD/PS-0 RSD/PS-05 QSD/PS-03 QSD/PS-040 No. Parts name aterial Q ty Parts code f0 f0 F Piston packing Hydrogenated nitrile rubber NHY-50 NHY-3 NHY-0 NHY-0 G Rod packing Hydrogenated nitrile rubber UHR-A UHR-3 UHR-45 UHR-5 H Dust wiper Hydrogenated nitrile rubber DHS- DHS-3 DHS-45 DHS-5 I Rod gland O-ring Hydrogenated nitrile rubber G-45 G-5 G-75 G-95 Double acting double rod cylinder set QSD/PS-050 QSD/PS-03 QSD/PS-00 QSD/PS-0 A copper piece for protecting the threads of the rod gland is included in the packing set. Be careful not to lose it.

44 Packing set Packing set Sectional drawings/packing list HQS 44 Packing list c Fluoric rubber/hqsd, HQSRD No. F G H I Parts name aterial Q ty Piston packing Fluoric rubber Rod packing Fluoric rubber Dust wiper Fluoric rubber Rod gland O-ring Fluoric rubber Parts code f0 f0 P- P-34 P-44 P-53 P-70 P-90 UHR- UHR- UHR-A UHR-3 UHR-45 UHR-5 DHS- DHS- DHS- DHS-3 DHS-45 DHS-5 G-5 G-35 G-45 G-5 G-75 G-95 Double acting double rod cylinder set QSD/PS3-03 QSD/PS3-040 QSD/PS3-050 QSD/PS3-03 QSD/PS3-00 QSD/PS3-0 The hardness of the O-ring (P G) is Hs90. A copper piece for protecting the threads of the rod gland is included in the packing set. Be careful not to lose it. n utting fluid proof type/hqswd, HQSWRD No. F G H I Parts code Parts name aterial Q ty f0 f0 Piston packing Rod packing Dust wiper Rod gland O-ring Hydrogenated nitrile rubber Hydrogenated nitrile rubber anned hydrogenated nitrile rubber Hydrogenated nitrile rubber NHY-3 UHR- (DYL-S) G-5 NHY-40 UHR- (DYL-S) G-35 NHY-50 UHR-A (DYL-S) G-45 NHY-3 UHR-3 (DYL-3S) G-5 NHY-0 UHR-45 (DYL-45S) G-75 NHY-0 UHR-45 (DYL-5S) G-95 Double acting double rod cylinder set QSWD/PS -03 QSWD/PS -040 QSWD/PS -050 QSWD/PS -03 QSWD/PS -00 QSWD/PS -0 You could replace it, but we recommend that you change the Rod gland ass y including Dust-Wiper. Because the damage to the gland may lead to the leakage of oil. In this reason, Dust-Wiper isn t included in the seal kit. But you could buy only Dust-Wiper according to your separate order. The dust wipe O is pressed in the rod gland to be incorporated with it, and cannot be replaced singly. When replace together with the rod gland. A copper piece for protecting the threads of the rod gland is included in the packing set. Be careful not to lose it.

45 Hydraulic ylinder 0H- Series New brand satisfying global standards onforming to ISO0- (JIS B37-) Features Seals in sliding sections conform to ISO standards groove size. Normally equipped switches for cylinders with bores from 3 mm to 0 mm. (E mark switches are also available.) Adoption of the floating cushion unique to TAIYO (patent pending). Improved start performance. ushion performance is hard to be affected by fluctuations in oil temperature. (hange in cushioning time is less to fluctuations in oil temperature.) ain specifications Rod series: Two, A and B Nine types of bores from 3 mm to 0 mm are available. Ports are applicable to Rc (tapered thread) and G (straight thread). ore compact and lightweight than our 40H-. Normally equipped high-performance cushion ushion valve easy to adjust. Specifications (mm) : φ3 φ40 φ 50 φ 3 φ 0 φ 0 φ 5 φ 40 φ 0 Nominal pressure : Pa ounting style : SD FA FB EA EB FE LA A B TA T Hydraulic ylinder -/R Series The first Pa new series with magnetic proximity switch (bore from 40 mm to 0 mm) Features ore lightweight, compact, and low-cost than H-3 Series. Double rod type and larger bore type (from 0 mm to 50 mm) are added. eets request for space-saving design. Normally equipped high-performance cushion Rod A is also available in addition to standard rod. G thread type is also available. Specifications NEW (mm) : Standard type φ40 φ50 φ 3 φ 0 φ 0 φ 5 φ 40 φ 0 φ 0 φ0 φ φ 50 Switch set φ40 φ 50 φ 3 φ 0 Nominal pressure : Pa Tiny- Hydraulic ylinder 0Z- Series Pa round type tiny-bore hydraulic cylinder with high-performance cushion Features Pa tiny-bore hydraulic cylinders with bores, 5, and 3 mm. ushion adjustable to all the bores and floating cushion. Nitrile rubber and hydrogenated nitrile rubber are used as the materials of seals for sliding section, widen the applicable range of hydraulic fluid. ompletely identical mounting dimensions to those of 70Z- Series. New small type switches AX and AZ. Specifications (mm) : φ φ 5 φ 3 Nominal pressure : Pa

46 Full line of equipment with various series to meet the needs of users ompact Design Hydraulic ylinder 35S- Series Wide selection of models corresponding to every application Features Standardized switch outfit type. Specifications (mm) : φ φ5 φ 3 φ 40 φ 50 φ 3 Nominal pressure : 3.5 Pa Type : Double-acting single rod/double rod type Standard type/switch set ompact Design Hydraulic ylinder 0S- Series Space saving/ Pa compac design hydraulic cylinder Features Allows economical selection depending on use frequency and operating pressure. onforms to JIS B37. Fatigue test class A. Great variety of mounting styles, SD, LD, FA, and FB. Specifications (mm) : φ φ5 φ 3 φ 40 φ 50 φ 3 φ 0 φ 0 Nominal pressure : Pa Type : General purpose type/utting oil proof type Double-acting single rod/double rod type Standard type/switch set ompact Design Hydraulic ylinder 0S- Series Pa compact design hydraulic cylinder requires less mounting space Features Standardized cutting oil proof type. an be disassembled for easier maintenance. Allows highly precise mounting. Standardized switch outfit type. (agnetic proximity type and cutting oil proof type) Great variety of mounting styles, SD, LA, LD, FA, and FB. Dog limit switch outfit type is also available. (Semi-standard type) Specifications (mm) : φ φ 5 φ 3 φ 40 φ 50 φ 3 φ 0 φ 0 φ 5 Nominal pressure : Pa Type : General purpose type/utting oil proof type Double-acting single rod/double rod/foot type Standard type/switch set