THIS PAGE INTENTIONALLY LEFT BLANK (IFC)

Transcription

1

2 THIS PAGE INTENTIONALLY LEFT BLANK (IFC)

3 TABLE OF CONTENTS AIR SYSTEM VAC Coil Assemblies Asco Jucomatic 110 VAC Coil Assemblies SMC 2 Way Directional Control Valves 4 Way Directional Control Valves General & Misc Items BEARINGS BELT CONVEYOR Return Idler Assemblies Troughing Idler Assemblies Troughing Idler Assemblies Individual Rolls Hardware Common to Ross Idler Assemblies Radial Conveyors Ross BUTTERFLY VALVES Bray Butterflies Dynaflow (Virgo) Butterflies Keystone / Ultraflo Butterflies Wam Butterflies Weco Butterflies CEMENT AERATION CYLINDERS & GATES Air Cylinders Johnson Plants Air Cylinders Ross Plants Aggregate Gates Ross Blocking Gate (E-Gate) Plug Valves & Gates Johnson DISCHARGE HEADS ROSS DISTRIBUTOR REMOTES DUST COLLECTORS Bag Type Dust Collectors Johnson Bag Type Dust Collectors Ross V 100 / V 200 / V 400 Parts V 700 / V 1400 / V 2100 / V 2800 Cartridge Type Dust Collector Parts Control Parts For 3 & 6 CP Dust Vents CPV Dust Collector Control Panel Dust Collectors C & W ELECTRICAL PARTS CB-1 Equipment Manual Panels Ross Miscellaneous INDICATORS LIMIT SWITCHES LINERS...46 MIXER DRUMS...48 MIXERS JOHNSON...50 Hydraulic Power Units MIXERS ROSS Components Drive Components Hydraulic Cylinders & Components Hydraulic Components Mixer Accessories PNEUMATIC & ELECTRICAL VIBRATORS SCREW CONEYOR COMPONENTS Boss Exec Rustler 110, Rustler 160, Rustler II, Rustler R3 Uniplant 100 UniRover U1248 SHROUDS Boots & Clamps GR Shrouds Shrouds for: Bandit B5, Bandit B12 Rustler R3 UniRover U1248 New Style 30 Discharge Head Standard Old Style 30 Discharge Head Uniplant & Old Style 24 Discharge Head WATER SYSTEM...64 ATC Counters Badger Water Meters Common Parts For All Badger Meters Water Strainers ORDER FORM

4 IMPORTANT NOTICES This reference guide for Terex concrete plant parts is not all inclusive for every equipment model available. Every effort has been made to capture the parts for models still in operation, regardless of current production status. Images are not scaled to size. A form is provided at the back of this book if you need additional reference guides. Please send your request together with your contact information (company name / phone / fax / ), and pertinent mailing information using any of the following: Phone: (888) Fax: (405) Attn: Parts Literature & Support Mail: parts@terexrb.com Terex Roadbuilding Attn: Parts Literature / Customer Service PO Box 1985 Oklahoma City, OK Important Notes / Acknowledgments: Manufacturer s names and products listed in this guide are either registered trademarks or pending trademarks TM and used in a non-trademark manner for explanatory purposes only. Effective Date: April Product specifications and prices are subject to change without notice or obligation. The photographs and/or drawings in this document are for illustrative purposes only. Refer to the appropriate Operator s Manual for instructions on the proper use of this equipment. Failure to follow the appropriate Operator s Manual when using our equipment or to otherwise act irresponsibly may result in serious injury or death. The only warranty applicable to our equipment is the standard written warranty applicable to the particular product and sale, and Terex makes no other warranty, express or implied. Products and services listed may be trademarks, service marks or trade-names of Terex Corporation and/or its subsidiaries in the USA and other countries. All rights are reserved. Terex is a registered trademark of Terex Corporation in the USA and many other countries Terex Corporation All Rights Reserved No part of this manual may be reproduced in any way without the express prior written consent of Terex Corporation. 2

5 NOTES: COMMON ABBREVIATIONS USED IN THIS GUIDE INCLUDE: TRB # Terex Roadbuilding Part Number BWD PT# Brownwood Part Number CHAMP PT# Champaign Part Number I/R Ingersoll Rand IMAGES ARE NOT SCALED TO SIZE. 3

6 AIR SYSTEMS 110 VAC Coil Assemblies - ASCO JUCOMATIC ASCO # BWD PT#: Two Position, Four-way, Single Solenoid Type (3/4 body family) Inching, Three Position,, Four-way, CLOSED CENTER Double Solenoid Type (3/4 body family) Manifold Type Sub-Base PS (stacking type), ½ NPT ports in end of manifold Sub-Base End-Plate Kit PS (for SMC Sub-Bases) NOTES: Rebuild kits for the Jucomatic valves are not available. Complete banks of Jucomatic valves can be replaced by complete banks of SMC valves. The recommended air system lubricant for ALL Johnson-Ross air systems is Dextron type Automatic Transmission Fluid (ATF). 4

7 110 VAC Coil Assemblies - SMC Standard 4-way air control valve on Bandit / Rustler / etc. plants. These valves are mounted in banks on a manifold type sub base. Two types of valves are used: (a) Two position, single solenoid valves control fill gates and the water system; and (b) Three position, double solenoid valves are used on the batcher discharge gates to provide inching control. SMC# BWD PT#: Two Position, Four-way, NVFS5110-3DZA Single Solenoid Type (3/4 body family) Repair Kit: PS KT-VFS5110 Pilot. valve assy: PS SF4-3FA-30 AIR SYSTEMS Inching Three Position, NVFR5310-3DZA Four-way, CLOSED CENTER, Double Solenoid Type (3/4 body family) Repair Kit: PS KT-VFR5300 Pilot valve assy: PS SF4-3FA-70 Manifold Type Sub-Base MBF (stacking type), ½ NPT ports in end of manifold Sub-Base End-Plate Kit MEF573LR (for SMC Sub-Bases) Three Position, Four-way, VFS5410-3DZA OPEN CENTER, Double Solenoid Type (3/4 body family), NON-Inching (Used on 1248 swing-chute with transit-mix discharge option) 5

8 AIR SYSTEMS 2 WAY DIRECTIONAL CONTROL VALVES 110 VAC Coil Assemblies - ASCO ASCO# BWD PT#: 3/8 2-way, pilot operated G Used for aeration and vibrator actuation Repair Kit: Coil: D 3/4 2-way, pilot operated G Used for aeration and vibrator actuation Repair Kit: Coil: D 1 1/4 2-way, pilot operated G8 Used for trim water on 1248 s and similar applications. Repair Kit: Coil: D 1 1/2 2-way, pilot operated G Used for aeration actuation in systems with low pressure-high volume aerator pumps. Repair Kit: Coil: D Pulse-Jet Valve 1, 2-way, G pilot controlled Pulse-Jet valve for 1, 3, & 6 CP, and, 12, 16, 24, 32, and 40 CPV Central Dust Collectors Repair Kit: Coil: D Four-way, Two Position, Single Solenoid Type (1/8 body, 1/4 ports, NAMUR Interface, for water butterfly actuators) Repair Kit (Spool & seal kit): K Repair Kit (Pilot seal kit):

9 4 WAY DIRECTIONAL CONTROL VALVES 110 VAC Coil Assemblies - PARKER / SCHRADER BELLOWS NOTE: The L705 two position and L695 three position valves are complete stand-alone valve assemblies. The L675 two position and L665 three position valves require a separate sub-base. P/SB# Two Position, Four-way, Single L Solenoid type with integral sub-base (1/2 ports) Replaces L Repair Kit: K Shock Pad: K AIR SYSTEMS Inching, Three Position, Four-way, L Double Solenoid Type with integral sub-base (1/2 ports) Repair Kit: K Shock Pad: K Two Position, Four-way, Single L Solenoid Type with separate sub-base (3/8 body family) Repair Kit: K Shock Pad: K Inching, Three Position, Four-way, L Double Solenoid Type with separate sub-base (3/8 body family) Repair Kit: K Shock Pad: K Single Station Sub-Base, 1/2 ports K (stand alone, for L665 & L675 series valves) 7

10 AIR SYSTEMS 4 WAY DIRECTIONAL CONTROL VALVES 110 VAC Coil Assemblies - PARKER / SCHRADER BELLOWS NOTE: The L705 two position and L695 three position valves are complete stand-alone valve assemblies. The L675 two position and L665 three position valves require a separate sub-base. P/SB# Manifold Type Sub-Base, 1/2 ports K (for L665 & L675 series valves) Two Position, Four-way, Single Solenoid L Type with integral sub-base (1/4 ports) Repair Kit: K Shock Pad: K Two Position, Four-way, Single Solenoid L Type with integral sub-base (3/8 ports) Repair Kit: K Shock Pad: K Inching, Three Position, Four-way, L Double Solenoid Type with integral sub-base (3/8 ports) Repair Kit: K Shock Pad: K

11 Flow Control, 3/8 MNPT x 3/8 FNPT Flow Control, 1/2 MNPT x 1/2 FNPT GENERAL & MISCELLANEOUS ITEMS SMC AIR CONTROL & TUBE FITTINGS AIR SYSTEMS Quick Exhaust Assy, 1/2 MNPT x 1/2 Tube Quick Exhaust Assy, 3/8 MNPT x 1/2 Tube Fitting, 1/2 MNPT x 1/2 Tube Fitting, 1/2 MNPT x 3/8 Tube Fitting, 1/4 MNPT x 3/8 Tube Fitting, 3/4 MNPT X 3/4 Tube, 3/4 Ferrule Nut Fitting, 3/8 MNPT x 3/8 Tube Fitting, 3/8 MNPT x 1/2 Tube Fitting, 3/8 MNPT x 3/8 Tube, Aeration L Fitting, 3/8 MNPT x 3/8 Tube, Aeration T Fitting, M4 to 1/4 MNPT (for WAM Butterflies) Tubing, 3/4 Air Brake Tubing Tubing, 3/8 Air Brake Tubing Tubing, 1/2 Air Brake Tubing

12 AIR SYSTEMS Auto Drain Assy, 1/2 inlet port Dryer 5MC, 3/4 body 77SCFM Gauge, 160 PSI GENERAL & MISCELLANEOUS ITEMS MISCELLANEOUS AIR SYSTEM PARTS 3/4 Regulator /4 Filter /4 Filter, Auto Drain for Bowl Assy /4 Filter, Bowl Assy, metal (sight gauge & auto drain) 3/4 Filter, Element (40 micron) /4 Filter, Twist Drain for Bowl Assy /4 Lubricator /4 Lubricator, Bowl Assy (metal) /4 Lubricator, Sight Dome & Fill Cap Intake Filter, for 10 HP I/R Compressor AIR COMPRESSOR PARTS Drive Belt, for 10 HP I/R Compressor Tank Gauge, for all I/R Compressors 55-PS PS Synthetic Oil, for all I/R Compressors

13 BEARINGS GENERAL & MISCELLANEOUS ITEMS Plug valve bearing bolt flange, std duty, 1-1/ bolt flange, std duty, bolt flange, std duty, 2-3/ bolt flange, std duty, 2-1/ bolt flange, std duty, bolt flange, std duty, 1-1/ Needle type roller bearing Pillow Block, std duty, Pillow Block, std duty, 1-15/ Pillow Block, std duty, 2-7/ Pillow Block, std duty, 2-15/ Pillow Block, std duty,

14 BELT CONVEYOR RETURN IDLER ASSEMBLIES Return Idler Assemblies and Impact Idler Assemblies include mounting brackets and pins. Individual rolls come with bearings mounted; no pins or mounting brackets are included. CHAMP PT# BWD PT#: 4 x 24 1/2 Roll X24.5RR Flat Idler (load side) for Live Bottom Batchers with 24 Conveyors 4 x 26 3/4 Roll Return Idler for 24 flat conveyors on live bottom batchers for 100 Uniplants. 4 x 30 1/2 Roll Return Idler for 24 Ross Inclined Conveyors & for Flat Idler (load side) for 30 flat conveyor on live bottom batchers for 135 Uniplants. 4 x 32 3/4 Roll X32.34RR Return Idler for 30 flat conveyor on live bottom batchers for 135 Uniplants. 4 x 36 3/4 Roll Return Idler for 30 Ross Conveyors 4 x 42 3/4 Roll Return Idler for 36 Ross Conveyors 4 x 54 3/4 Roll Return Idler for 48 Ross Conveyors IMPACT ROLL ASSEMBLIES Used as first return idler, 5 or 6 x 2 Rubber Rollers on machined tubes, 24 ½ to 54 3/4 (for 24 to 48 conveyors). Impact Roll for 24 conveyor, with 5 rubber rollers Impact Roll for 30 conveyor, with 5 rubber rollers Impact Roll for 36 conveyor, with 5 rubber rollers Impact Roll for 48 conveyor, PS with 5 rubber rollers 5 Rubber Wheel for Impact Roll

15 TROUGHING IDLER ASSEMBLIES BELT CONVEYOR These troughing roller assemblies have pin clips instead of the removable stub shaft. Old style assembly is no longer available. These troughing idlers match the profile and height of the original Ross troughing idlers. CHAMP PT# BWD PT#: 24 x 20 Ross Troughing Idler x 35 Ross Troughing Idler x 20 Ross Troughing Idler x 35 Ross Troughing Idler x 35 Ross Troughing Idler x 35 Ross Troughing Idler X35ETRA 13

16 BELT CONVEYOR TROUGHING IDLER ASSEMBLIES - INDIVIDUAL ROLLS FOR ROSS Individual rolls come with bearings mounted; no pins or mounting brackets are included. CHAMP PT# BWD PT#: 4 x 8 1/2 Roll NA Replace Idler Assy Fits Ross 24-3 required Fits Ross 30-2 required PLUS /2 roll 4 x 12 1/2 Roll NA Replace Idler Assy X12.5TR For Ross 36 equal length 4 x 14 1/2 Roll NA Replace Idler Assy Center Roll for Ross 30 4 x 16 1/2 Roll Fits Ross 48 x 35 equal length NA Replace Idler Assy HARDWARE - COMMON TO ALL ROSS IDLER ASSEMBLIES CHAMP PT# BWD PT#: Standard Roll Bearing Used on all Ross Design Rolls (Troughing, Flat, Return, & Impact) Center Mounting Shaft Double-ended shaft used to mount inboard ends of troughing rolls, and both ends of center rolls. End Mounting Shaft Single-ended shaft used to mount outboard ends of troughing rolls, and all Flat Idlers and Return Idlers. Return & Flat Idler Mount Pillow Block style mounting block for flat and return idlers, accepts End Mounting Shafts above. Drop Hanger Brackets, 1 1/2 PS Drop Hanger Brackets, 4 1/

17 Drive Wheel, 12 x 4, 2-3/16 bore, steel wheel rubber faced RADIAL CONVEYORS - ROSS BELT CONVEYOR Follower Wheel, 12 x 4, 1 bore NOTES: 15

18 BUTTERFLY VALVES Actuator for 2 & 3 Bray Butterflies BRAY BUTTERFLIES Actuator for 4 & 6 Bray Butterflies Namur Interface Kit: for installing ASCO 551 air control valve 4 Butterfly Butterfly Parts, Disc Seal Butterfly Butterfly Parts, Disc Seal Butterfly Parts, Disc & Stem PS Butterfly Butterfly Parts, Disc Seal Butterfly Parts, Actal Bushing PS (for stem on disc) 2 6 Butterfly Parts, Buna-N stem seal PS

19 Actuator for 2 to 6 Dynaflow Butterflies DYNAFLOW (VIRGO) BUTTERFLIES BUTTERFLY VALVES Actuator for 10 Dynaflow PS001331A Adaptor (BWD PT# ) for and 3 Dynaflow using BR80-D8 Actuator Adaptor (BWD PT# ) for Dynaflow using BR80-D8 Actuator Adaptor sleeve for 10 Butterfly PS001331B 10 Butterfly PS Butterfly (BWD PT# ) uses B1 adaptor for BR80-D8 Actuator 3 Butterfly (BWD PT# ) uses A1 adaptor for BR80-D8 Actuator 3 Butterfly w/ Actuator Butterfly Disc Seal Kit Butterfly uses A1 adaptor for BR80-D8 Actuator 17

20 BUTTERFLY VALVES KEYSTONE / ULTRAFLO BUTTERFLIES 5 Butterfly w/ Actuator PS Butterfly ONLY Butterfly Assy Butterfly with Actuator / no limit switch Butterfly Parts, Shaft PS Butterfly Wrench Arm Actuator, 10 Butterfly Coil, TRS-150 Actuator PS PS Actuator (Vane type) for 2 to WECO BUTTERFLIES 2 Weco Butteryfly (No Actuator) Weco Butterfly Seat Weco Butterfly Disc Weco Butterfly (No Actuator) Weco Butterfly Seat Weco Butterfly Disc Weco Butterfly (No Actuator)

21 WAM BUTTERFLIES BUTTERFLY VALVES Nomenclature: V1FS (size, metric/std) Single flanged body with beaded extension on output side to receive a shroud, with cast iron disc. V2FS (size) G - Double Flanged body, cast iron disc. Size conversions: 100mm = 3.94 = 4 nominal size 150mm = 5.90 = 6 nominal size 200mm = 7.87 = 8 nominal size (8 3/4 boot ID) 250mm = 9.84 = 10 nominal size (10 3/4 boot ID) 300mm = = 12 nominal size (12 3/4 boot ID) 350mm = = 14 nominal size 400mm = = 16 nominal size The black seal material is superior when using the butterfly for powder applications. The WAM butterflies are for powder only, they will not hold water. Thread adapter for all WAM Actuators (5M male to 1/8 MNPT) CP 101 Actuator, for 8-12 Butterflies (BWD PT#: ) CP 125 Actuator, for 14 & 16 Butterflies Adapter - allows use of CP125 actuator on Butterfly M22 Limit Switch, fits all actuators (BWD PT#: ) Hexagonal Bushing (pivot bushings, 2 required per butterfly, fits all sizes) Disc seal for 6 WAM Butterfly PS WAM Butterfly, with CP 101 Actuator, and M22 Limit Switch 8 WAM Butterfly ONLY (BWD PT#: ) 19

22 BUTTERFLY VALVES Disc Seal for 8 WAM Butterfly (BWD PT#: ) WAM BUTTERFLIES (continuted) Mounting Flange for 8 WAM Butterfly WAM Single Flange Butterfly ONLY WAM Single Flange Butterfly with Actuator & Limit Switch 10 WAM Double Flange Butterfly ONLY Disc Seal for 10 WAM Butterfly Mounting Flange for 10 WAM Butterfly (BWD PT#: ) 12 WAM Single Flange Butterfly ONLY WAM Double Flange Butterfly ONLY WAM Single Flange Butterfly with Actuator & Limit Switch 12 WAM Double Flange Butterfly with Actuator & Limit Switch Disc Seal for 12 WAM Butterfly WAM Single Flange Butterfly ONLY

23 NOTES: 21

24 CEMENT AERATION Used on Ross plants from approximately to 2000 WAM CEMENT BATCHER AERATORS CONVEYOR COMPONENTS SILO AERATORS - RECTANGULAR PADS USED ON ROSS PLANTS UNTIL 2000 ADC Aeration Pad with ADK Mounting Kit ADC Aeration Pad without ADK Mounting Kit ADK Mounting Kit Positioning bracket C clamp Bin wall gasket (thick) Aerator gasket (thin)

25 CEMENT AERATION JOHNSON-ROSS - PARTS USED ON ALL NEW PLANTS Silo & Batcher Aerators: Use 3/8 air brake tubing & 3/8 weld flange, used on Ross plants after 2000 L Type Aerator T Type Aerator Diffuser Disc Effective August 1, 2004, diffuser assembly will have a snap ring to keep disc in place. This ring will only work with new style body. Old style diffusers can be replaced with new style. Snap Ring OLD JOHNSON SILO AERATORS USED ON JOHNSON PLANTS Quick Connect - Male with diffuser disc Quick Connect - Male without diffuser disc Quick Connect - Female Weld Flange, 3/8 FNPT Diffuser Disc

26 CYLINDERS & GATES AIR CYLINDERS JOHNSON PLANTS SINGLE STAGE AIR CYLINDERS 3 x 3-1/2 Trunnion Mount w/adjustable bolt x 5 Trunnion Mount w/adjustable bolt x 8 Trunnion Mount w/adjustable bolt x 10-1/2 Trunnion Mount w/adjustable bolt /2 x 5 Trunnion Mount w/adjustable bolt /2 x 8 Trunnion Mount w/adjustable bolt /2 x 10 Trunnion Mount w/o adjustable bolt /2 x 12 Trunnion Mount w/o adjustable bolt /2 x 15 Trunnion Mount w/o adjustable bolt /2 x 16 Trunnion Mount w/o adjustable bolt /2 x 5 Clevis Mount /2 x 8 Clevis Mount x 8 Trunnion Mount x 8 Clevis Mount

27 CYLINDERS & GATES REPAIR KITS: AIR CYLINDERS JOHNSON PLANTS REPAIR KITS and HARDWARE 3 diameter, Single Stage diameter, Two Stage /2 diameter, Single Stage /2 diameter, Two Stage diameter, Single Stage diameter, Single Stage Bronze Bushing HARDWARE: Yoke end (4-1/2 cylinders) Yoke pin (4-1/2 cylinders) Yoke end (6 cylinders) Yoke pin (6 cylinders)

28 CYLINDERS & GATES 2 x 8 Cylinder (BWD PT# ) Rebuild Kit for 2 cylinders Air Cushion Kit AIR CYLINDERS ROSS PLANTS 2 1/2 x 6 Cylinder used on Super x 8 Cylinder (BWD PT# ) Rebuild Kit for 4 Cylinder Air Cushion kit for 4 cylinders x 10 Cylinder (BWD PT# ) Parker/Schrader-Bellows Rod Gland kit For Econo Ram II 4 bore cylinders ENERGY CYLINDERS NO LONGER AVAILABLE REPLACE WITH AIR PRO CYLINDERS AND THE FOLLOWING MOUNTING MODIFICATIONS Upper Cylinder Mount for 4 Cylinder Use for conversion from old Energy Cylinders to NFPA type Lower Cylinder Mount for 4 Cylinder Use for conversion from old Energy Cylinders to NFPA type 26

29 CYLINDERS & GATES AGGREGATE GATES - ROSS CLAMSHELL GATE PARTS Pivot Bolt, 4 reqd per gate (Old Style) Four (4) required per gate assembly Pivot Bolt (New Style) Pivot Bolt Nut, thin, self-locking (Old Style) Four (4) required per gate assembly Pivot Bushing, (Old Style) Four (4) required per gate assembly 1/8 Grease Zerk (Old Style) Four (4) required per gate Cotter Pin (New Style) 000A Flat Washer (New Style) 000A Bushing Sleeve Four (4) required per gate Garmax Bearing (New Style) Clamshell Gate End Plate Assembly Two (2) required per gate assembly 10 Clamshell Gate End Plate Assembly Two (2) required per gate assembly BLOCKING GATE (E-GATE) Gate assembely Blocking Plate Angle /2 Gum Rubber, 1-2 long

30 CYLINDERS & GATES PLUG VALVES AND GATES JOHNSON Old Style Plug Valve: Cone & Pushrod assembly Rubber Seal Ring (10 ID) Shroud Clamp Canvas Taper Sock Pin Operation Lever x 30 Plug Valve: Rubber Wipe (3 x 30 ) Rubber wipe (11/16 x 8-1/8 ) Clamp bar Plug Yoke Yoke Pin Bearing Rocker arm x 18 Plug Valve

31 PLUG VALVES AND GATES JOHNSON Discharge Swing Chute: Swing chute Shroud Shroud clamp Bearing CYLINDERS & GATES NOTES: 29

32 DISCHARGE HEADS - ROSS TRANSFER CONVEYOR DISCHARGE HEADS BWD PT#: STD 30 TRANSIT MIX DISCHARGE HEAD The main discharge is oval shaped, 24 x 30 (21 x 27 inside dimensions), the water ring is on the bottom edge, and a 6 pipe passes the cement through the discharge head. This discharge head typically requires an 8W x 6P x 12 DM shroud to connect the cement batcher discharge butterfly to the top of the 6 pass-through pipe, then a 6P x 18 to 36 long GR shroud to carry the cement into the transit mix truck. This discharge head typically uses an 88 x 18 to 30 long GR shroud to carry the aggregates to the transit mix truck. BWD PT#: STD 30 TRANSIT MIX DISCHARGE HEAD FOR BANDIT PLANTS Main discharge is oval shaped, 24 x 30 (21 x 27 inside dimensions), water ring on bottom edge, and 6 cement pass-through pipe, same shroud requirements as the Std discharge head above. THIS DISCHARGE HEAD LOOKS IDENTICAL TO THE STD HEAD ABOVE BUT HAS A SPECIAL OFFSET TO WORK PROPERLY ON THE BANDIT PLANTS. BWD PT#: STD 24 TRANSIT MIX DISCHARGE HEAD W Main discharge is 24 1/2 OD and 21 ID, round, water ring on bottom edge, and 6 cement pass-through pipe. This discharge head typically requires an 8W x 6P x 12 DM shroud to connect the cement batcher discharge butterfly to the top of the 6 pass-through pipe, then a 6P x 18 to 30 long GR shroud to carry the cement into the transit mix truck. This discharge head typically uses a 77 x 18 to 30 long GR shroud to carry the aggregates to the transit mix truck. 30

33 DISCHARGE HEADS - ROSS TRANSFER CONVEYOR DISCHARGE HEADS BWD PT#: OLD STYLE 30 TRANSIT MIX DISCHARGE HEAD The main discharge is round, 21.5 OD, water ring is high inside discharge head and 4 x 4 V plate for gum rubber boot instead of 6 cement pass-through pipe. This type of discharge head will require an 8W x 36 to 48 long GR shroud for the cement. This boot attaches to the cement batcher discharge butterfly and extends all the way through the discharge head, into the transit mix truck. This discharge head typically uses an 68 x 18 to 30 long GR shroud to carry the aggregates to the transit mix truck. BWD PT#: OLD STYLE 30 TRANSIT MIX DISCHARGE HEAD FOR BANDIT PLANTS The main discharge is 24 diameter, round, water ring is high inside discharge head and 4 x 4 V plate for gum rubber boot instead of 6 cement pipe. This type of discharge head will require an 8W x 36 to 48 long GR shroud for the cement. This boot attaches to the cement batcher discharge butterfly and extends all the way through the discharge head, into the transit mix truck. This discharge head typically uses an 68 x 18 to 30 long GR shroud to carry the aggregates to the transit mix truck. BWD PT#: OLD STYLE 24 TRANSIT MIX DISCHARGE HEAD The main discharge is 21 diameter and round, water ring mounted high inside discharge head and 4 x 4 V plate for gum rubber boot instead of 6 cement pipe. This type of discharge head will require an 8W x 36 to 48 long GR shroud for the cement. This boot attaches to the cement batcher discharge butterfly and extends all the way through the discharge head, into the transit mix truck. This discharge head typically uses an 68 x 18 to 30 long GR shroud to carry the aggregates to the transit mix truck. Cement Pass-thru Pipe This is a diagram of a new style discharge head. The new style has a pass thru pipe for the cement where the old style has a V plate trough that allows a rubber boot for cement to pass thru. The design is the same for 24 and 30 discharge heads; only the width dimensions will be different. The new style can replace an old style with some mounting modifications. Must include boots for new style if using for replacement. 31

34 DISCHARGE HEADS - ROSS MISCELLANEOUS PARTS FOR DISCHARGE HEADS QTY REQ D Supporting Angle r 1 Supporting Angle l 1 Clamping Bar Tube Clamp Cement Tube Plate Plate /8 x 4 Rubber x 2 8 Long Bolt, Hex Head 3/8 16 UNC x 1 1/4 Long 000-A Bolt, Hex Head 3/8 16 UNC x 1 1/2 Long 000-A Bolt, Hex Head 3/4 10 UNC x 1 1/2 Long 000-A Nut, Hex 3/8 16 UNC 000-A Nut, Hex 3/4 10 UNC 000-A Washer, Flat 3/8 000-A

35 TURNHEAD & PIVOT DISTRIBUTOR REMOTES Garage door type: Receiver Transmitter Antenna DISTRIBUTOR REMOTES Receiver 4 momentary switches Transmitter 4 momentary rocker switches NOTES: 33

36 DUST COLLECTORS BAG TYPE DUST COLLECTORS JOHNSON CSJ-125 Bags x 46 3/4 CSJ-250 Bags x 86 3/4 CSJ-1000 / CHAMP PT#: BWD PT#: CA 20 Parts (Cement Batcher Vent, reference drawing # ) BAG TYPE DUST COLLECTORS ROSS Bags, 2-4 1/2 x 8 1/4, 8 required Bag Clamps, 29 long, 8 required Strap Style Clamp, order by inch length needed ($5.03 for band & clamp) Band Material, 1/2 SS Clamp Blower (Optional larger blower, reference drawing # ) V 100 Parts (Cement Silo Vent, reference drawing # ) Bags, 3-7 1/2 x 8 1/4, 14 required Bag Clamps, 29 long, 14 required Strap Style Clamp, order by inch length needed Band Material, 1/2 SS Clamp Blower PB12A 11 x 2 3/4 wheel for 2HP Exhaust Fan 55-PS PB12AW (5/8 shaft size) Motor, 2HP, 3PH, 60HZ, 230/460V 55-PS Butler DF-4C Dust Collector Parts

37 BAG TYPE DUST COLLECTORS ROSS (continued) DUST COLLECTORS CHAMP PT#: BWD PT#: V 200 Parts Bags, 7-1 x 8 1/4, 14 required (recommended for Cement) Bags, 7-1 x 8 1/4, 14 required (recommended for Flyash) Bag Clamps, 29 long, 14 required Strap Style Clamp, order by inch length needed Band Material, 1/2 SS Clamp Exhaust Fan, 2 HP PB12A 11 x 2 3/4 wheel for 2HP Exhaust Fan 55-PS PB12AW (5/8 shaft size) V 400 Parts Bags, 7-1 x 8 1/4, 28 required (recommended for Cement) Bags, 7-1 x 8 1/4, 28 required (recommended for Flyash) Bag Clamps, 29 long, 28 required Strap Style Clamp, order by inch length needed ($5.03 for band & clamp) Band Material, 1/2 SS Clamp Exhaust Fan, 3 HP PB123HP 13 x 3.2 wheel for 3HP Exhaust Fan 55-PS (5/8 shaft size) Vibrator V 700, V 1400, V 2100, V 2800 Bags, 8-1/4 X 9-4 1/2 (112 1/2 ) Number of bags required: V V V V

38 DUST COLLECTORS CARTRIDGE TYPE DUST COLLECTOR PARTS CHAMP PT#: BWD PT#: Either the Paper or Poly Media Cartridge can be used in any of the dust collectors. The poly media is slightly finer, and is washable. Paper Media Cartridge, 8 3/8 x 12 3/4 x cartridge, for 3CP, 6CP, and 1CP (BWD PT # Ref # DV) Poly Media Cartridge, 8 3/8 x 12 3/4 x cartridge, for 12, 16, 24, 32, and 40 CPV Central Dust Collectors (BWD PT # Ref # CDV) Cartridge Hanger, V Rod Welded onto plenum plate, for 3 & 6 CP, and 12, 16, 24, 32, and 40 CPV Central Dust Collectors Cartridge Hanger, Threaded Rod Hooks onto V Rod, for 3 & 6 CP, and 12, 16, 24, 32, and 40 CPV Central Dust Collectors Cartridge Holder Plate Assembly Round plate, with gasket. Supports the bottom cartridge, held by the threaded rod, for 3 & 6 CP, and 12, 16, 24, 32, and 40 CPV Central Dust Collectors Holder Plate Gasket Closed-cell foam gasket, 44-GASKET DVF GASKET DVF 12 OD X 8 ID x 3/8 thick, for 3 & 6 CP, and 12, 16, 24, 32, and 40 CPV Central Dust Collectors Holder Plate Nut with handle, holds round plate up, for 3 & 6 CP, and 12, 16, 24, 32, and 40 CPV Central Dust Collectors. Also used to hold door closed A031 Pulse-Jet Valve 1, 2-way, pilot controlled Pulse-Jet valve for Dust Collectors Door Gasket: 3/8 x 1 Closed cell foam gasket material 36

39 DUST COLLECTORS CARTRIDGE TYPE DUST COLLECTOR PARTS (continued) CHAMP PT#: BWD PT#: 6CP Air Manifold 6 round (new style) W CP Air Manifold CP Mating Flange A1 1-1/4 Rod, Air valve attachment Coupling, 3/4 NPT x 5, Cut in half Pipe Coupling, 3/4 x 5 NPT Pipe Coupling CONTROL PARTS FOR 3 & 6 CP DUST VENTS CHAMP PT#: BWD PT#: Differential Pressure Switch Pulse-Jet Controller Repeat Cycle Timer Circuit Assembly Timer Meg plug-in Pot for Timer (controls off time between cleaning cycles) Finder Relay Socket for Finder Relay J-Box Assembly

40 DUST COLLECTORS CPV DUST COLLECTOR CONTROL PANEL BWD PT#: White Lens (Round) Red Lens (Round) Green Lens (Round) Amber Lens (Round) Lamp Base VAC Lamp C & W DUST COLLECTORS Paper Media Cartridge, 8 x 19 cartridge PS for CP-35 Paper Media Cartridge, 8 x 39 cartridge for CP-1000, CP-1200 PS Paper Media Cartridge, 8 x 54 cartridge for CP-1000 Door Rubber Trim, rubber trim for CP style collectors Electrical Timer, sec timer for CP collectors Solenoid Valve, 3/4 Solenoid valve for CP-35 collector Double Bulkhead, 1 Bulkhead for Solenoid valve Auger Motor, 1 HP electric motor for CP-1000 auger PS PS PS PS PS Vane Feeder Motor, 1/2 HP, 71 frame, 230/460, PS RPM, electric motor for vane feeder on CP-1000 Vane Feeder Packing CP-1000 PS

41 ELECTRICAL PARTS CB-1 EPROM, w/ English, metered water and no moisture probe COMMON ELECTRICAL PARTS EQUIPMENT FOR ADDITION OF CB-1 CB-1 EPROM, w/ English, metered water and moisture probe CB-1 EPROM, w/ Spanish, metered water and no moisture probe CB-1 EPROM, w/ Spanish, metered water and moisture probe Printer, CB KVA Battery back-up Line Quench Arc Suppression board IQ-510 read out, DWI Lithium Battery for IQ and 510 PS AC Output fuse PS CB-1 Firmware PS CB-1 Board PS Controller i Card PS Ribbon Cable 55-PS Power Supply Kit 55-PS

42 ELECTRICAL PARTS BATCHER DISCHARGE SWITCHES Batcher discharge switch, two momentary contact pushbuttons Batcher discharge switch, Contactor NO Batcher discharge switch, Cover COMMON ELECTRICAL PARTS MANUAL PANELS - ROSS ON/OFF SWITCHES Run/Off, 2 position rotary Run/Off, Rotary contactor set, NO START/STOP STATIONS, ROTARY SWITCHES Start/Stop station, 3 position rotary, maintain LEFT, Momentary Right Start/Stop station, rotary contactor set, NO/NC FILL GATE SWITCHES Square pushbutton, momentary contact Contactor set, NO ADMIX FILL SWITCHES Square pushbutton, momentary contact Contactor set, NO ADMIX DISCHARGE SWITCH Square pushbutton, latching Contactor set, NO COMBINATION ADMIX FILL / DISCHARGE SWITCHES, ROTARY TYPE 3 position rotary, maintain RIGHT Rotary contactor set, NO/NO

43 INDICATOR LAMP PARTS Indicator light bulb Indicator light socket Indicator light lens, AMBER Indicator light lens, BLUE Indicator light lens, RED Indicator light lens, GREEN Indicator light lens, CLEAR Indicator light lens, WHITE Indicator light lens, YELLOW COMMON ELECTRICAL PARTS MANUAL PANELS - ROSS - continued ELECTRICAL PARTS KEY SWITCH Control, key switch Key switch, contactor set, NO EMERGENCY STOP SWITCH E-stop switch E-stop switch, contactor set, NO WATER CONTROL SWITCHES Water Stop & Reset Switch: Square pushbutton momentary contact Water Start & Reset switch, contactor set NO Water Select & Hold switch: Three position rotary Water Select & Hold, NC-NC contactor set Water Select & Hold, NO-NO contactor set

44 ELECTRICAL PARTS Line Starter - Non-Rev, Size 2, 120V COMMON ELECTRICAL PARTS MISCELLANEOUS Line Starter - Non-Rev, Size 3, 120V Relay Overload, Size 4, 144AMP Standard Motor Starter - Heater Pack Contactor - Non-Rev, 5 CH, 120V Timer (Midtex) Lamp, 120V Switch, 3 position maintained Switch, 2 position maintained Switch, 2 position key Fuse, 2A Fuse Block Finder Relay Base Socket for Finder Relay Strobe Light Bulb PS Strobe Light

45 INDICATORS BIN INDICATORS ROTO-BIN-DICATOR (UniRover U1248) Model R, Type 7 (115,1/60hz) Extension (Bindicator model) Paddle (3 Vane) Cord Grip Roll Pin Pipe /8 Half Coupling MONITOR Model KA (115,1/60) Extension 55-PS Paddle (3 Vane) Mounting Plate

46 INDICATORS MONITOR ROTO SIGN (Rustler R3 & Bandits) Roto Sign (115,1/60) Coupling, Screwed Banana Paddle Flex Coupling BIN INDICATORS Pipe Pipe Coupling MOISTURE PROBES Digital Microwave Moisture Sensor READOUT Slump Meter UPC Liquid Level Probe Circuit Board FLOAT ASSEMBLY Level Switch Coupling Pipe Ball, Float

47 LIMIT SWITCHES Limit switch, short travel LIMIT SWITCHES Limit switch, magnetic Roller arm Proximity switch Safety limit switch, conveyor

48 LINERS JOHNSON 12 YD 3 DRUM POLY LINERS QTY: Drum Liner Kit includes items #1 - #13: Front Cone Liner # Front Cone Liner # Girth Liner # Girth Liner # Rear Cone Liner # Rear Cone Liner # Back Cone Liner # Reinforcing Collar Liner # Spindle Cap Edge Liner # Spindle Cap Edge Liner # Spindle Ring Liner # Spindle Cap Liner # Blade Face Liner #

49 LINERS ROSS MIXER POLY LINERS FOR: 8, 10, 12 YD 3 ROSS TILT MIXERS QTY: 12 YD Liner Kit A1 includes: Nose Cone Liner YD Belly Band Liner Rear Cone Liner Hub Cone Liner Hub Cover Liner Hub Cap Liner (round) Sikaflex Adhesive Rubber Seal for Discharge Hood Rubber Only Seal Ring for 1 Poly Liners YD Belly Band Liner YD Belly Band Liner YD Blade Liner YD Blade Liner YD Blade Liner Kit A1 1 includes 4 each of: Face Liner Tip Liner Tip Liner Cone and Chute Liners (see diagram at right): Spill chute polyliner # Spill chute polyliner # Spill chute polyliner # Spill cone polyliner #

50 MIXER DRUMS Johnson Style Concrete Plant Mixer Drum (Ring Gear included) JOHNSON MIXER DRUMS Forged Ring Gear for Johnson Style Drum ROSS MIXER DRUMS Ross Style Concrete Plant Mixer Drum (Ring Gear included) A1 Ring Gear for Ross Style Drum

51 NOTES: 49

52 MIXERS - JOHNSON JOHNSON MIXER HYDRAULIC POWER UNIT 4OHP HYDRAULIC POWER UNIT Self Erect Valve Emergency Tilt Valve PS Complete Directional Valve 55-PS Handle (Lever) Assy PS Coil Handle (Lever) Only PS Pilot Valve 55-PS Flow Control Suction Strainer Body Valve (serial # req d) CALL FOR PN Cartridge PS Relief Valve Flow Control 55-PS Amplifier Card** Bolt Kit Dump Control Valve Sun Dump Valve** Solenoid & Coil PS /2 Coupling PS Coil Only PS Coupling insert PS /2 Coupling PS Vane Pump Clean Out Gasket PS Return Filter Filter Head Assy 55-PS Top Gasket PS Proportional Valve** Coil PS Motor, 40HP, 1800RPM, 230/460/60/3 Motor, 2HP, 1800RPM, 115/230/60/1 CALL FOR PN PS ** For Variable Speed Units Only Pressure Gauge ( PSI) Secondary Pump, gear Sight Level & Temperature Gauge PS

53 MIXERS - JOHNSON 51

54 MIXERS - ROSS ROSS MIXER COMPONENTS PADDLES & BOLTS CHAMP PT#: BWD PT#: 10 YD 3 (7.64 M 3 ) PADDLES & LEGS Includes complete bolt kit (noted below) and 12 support legs total: Four paddles: 3 legs per paddle W front support, 4 required W middle support, 4 required W rear support, 4 required W PADDLES ONLY W YD 3 (9.1 M 3 ) PADDLES & LEGS A Includes complete bolt kit (noted below) and 12 support legs total: Four paddles: 3 legs per paddle W1 -front support, 4 required W2 -middle support, 4 required W3 -rear support, 4 required W4 PADDLES ONLY (SINGLE) W BOLT KIT (same for 10 YD 3 & 12 YD 3 mixers) Includes 32 (thirty-two) 3/4 x 2 ½ grade 5 bolts with nuts and lock washers; and 48 (forty-eight) 1 x 4 grade 5 bolts with nuts and lock washers. QTY ITEM 32 3/4 x 2 1/2 grade 5 bolts 000A /4 nuts 000A /4 flat washers 000A /4 lock washers 000A x 4 grade 5 bolts 000A nuts 000A flat washers 000A lock washers 000A

55 MIXERS - ROSS Front Bearing, Cone (Nose Cone End) ROSS MIXER COMPONENTS BEARINGS & SEALS Front Bearing, Cup (Nose Cone End) Rear Bearing, Cone Rear Bearing, Cup Wear Ring For Rear Seal Rear Seal, Single Piece NOT split Rear Seal, Split Seal, Can be installed in the field. Glue (Rear Split Seal) Must use with Split Seal. One tube should be sufficient for one split seal. 53

56 MIXERS - ROSS 12 YD 3 MIXER 60 HP Motor, 60 HP, 1800 TEFC, T Frame DRIVE COMPONENTS Gear Reducer, Modified for tilting applications Gear Breather DCR Gear Scoop, G-Grid Line & Scoop GEARS & MISCELLANEOUS 18 Tooth Pinion Gear Ring Gear (Bull Gear) NOTE* 12 week lead time if not in stock INSTALLATION TOOL and CLAMPS REQUIRED for FIELD INSTALLATION (No charge if returned) Ring Gear Installation Tool Ring Gear Clamps (requires qty 10) A A1 54

57 MIXERS - ROSS HYDRAULIC CYLINDERS & COMPONENTS FOR: 8, 10, 12 YD 3 ROSS TILT MIXERS BWD PT#: Tilt Cylinder 4 x 48 with 2-3/4 rod Rod End with spherical bearing for x 48 Tilt Cylinder Spherical Bearing (Rod End) Rod End Cylinder Pin for W x 48 Tilt Cylinder Clevis Mount (lower cylinder mount) A for 4 x 48 Tilt Cylinder Spherical Bearing (Clevis Mount) Lower Cylinder Pin for x 48 Tilt Cylinder Main Pivot Pin 4 OD x 8 1/2 Long W Main Pivot Pin Bushing Receiver A & WITH Bushing Installed NOTE: This item is sold as one unit only and consists of TRB part sleeve, and bronze bushing. Neither can be sold separately. 55

58 MIXERS - ROSS HYDRAULIC POWER UNITS 40 HP (Paving operations) HP (Ready Mix) PVG HYDRAULIC VALVES PVG 120 Valve 40 HP Hydraulic Units PS Valve Coil, 24 VDC HYDRAULIC COMPONENTS PVG 12 Handle & Seal Kit PS PVG 32 Valve (SERIAL # REQUIRED) CALL FOR 15 HP Hydraulic Units PART NUMBER Valve Coil, 24 VDC PVG 32 Handle & Seal Kit MISC. COMPONENTS Filter (Return) for 40 HP Hydraulic Units PS PS Ramp Generator Seal Kit (pv15 pump) Gob Hopper MIXER ACCESSORIES Discharge Cone & Chute Telescoping Discharge Shroud (12 Travel) Telescoping Discharge Shroud (18 Travel) Telescoping Shroud Assy Telescoping Shroud with Wringer Wringer Gate - Standard Swing-away Drip Pan Swing-away Drip Pan Assy W PS PS A A A A A1 Splash Guard

59 PNEUMATIC & ELECTRIC VIBRATORS PNEUMATIC & ELECTRIC VIBRATORS Cleveland #3/4 SAEP Cleveland #1 SAEP WAM S36P (replacement for the BG-35) 1-1/4 #1125 VMS with mounting plate Piston type 1-1/ #1200 VMS with mounting plate Piston type Electric BGSF 36 / 100, 110 / 1 / Electric MVE U, / 460 / 30 / 60 Ball

60 SCREW CONVEYOR COMPONENTS SCREW CONVEYOR COMPONENTS RUSTLER 110 Head flight for fill screw (6 dia x 119 lg) Tail flight for fill screw (6 dia x 117 lg) Discharge screw for batcher (6 dia x 41 lg) RUSTLER 160 Standard Head flight for fill screw Standard Tail flight for fill screw Tail section assembly A1 Discharge screw for batcher (6 dia x 92 lg) RUSTLER II Head flight for fill screw (9 dia x 86 lg) Tail flight for fill screw (9 dia x 87 lg) RUSTLER R3 Hardware: Wood bearing, 2 : Hanger w/ bearing Head shaft spacer BOSS EXEC Head flight for silo screw (9 dia x 144-3/8 lg) Tail flight for silo screw (9 dia x 190-1/2 lg) Hardware: Coupling shaft field install kit A1 58

61 SCREW CONVEYOR COMPONENTS SCREW CONVEYOR COMPONENTS UNIPLANT 100 Discharge screw for batcher (6 dia x 69: lg) Hardware: Tail shaft, 1-1/2: x 9-1/ Coupling shaft, 1-1/2 x 11-1/ Bearing hanger, 1-1/ Hard iron bearing, 1-1/ Connecting bolts, 1-1/2 shaft Head shaft, 1-1/2 x 12-1/ Seal plate, 1-1/ UNIROVER U1248 Conversion Kit - move reducer from tail to head, Cement side Conversion Kit - move reducer from tail to head, Fly ash side Conversion Kit - Reducer adapter, Cement side Conversion Kit - Reducer adapter, Fly ash side Hardware: Wood bearing, Hanger w/ bearing C5 adjustable adapter C4 adjustable adapter

62 SHROUDS SHROUD CLAMPS CHAMP PT# BWD PT# Cable Clamp for 6 Pipe Cable Clamp for 8 WAM Cable Clamp for 10 WAM Cable Clamp for 12 Pipe Strap Style Clamp, order by the inch length required. Band Material, 1/2 SS Clamp BATCHER DISCHARGE DM SHROUDS BWD PT#: 8P x 6P x A Standard on BANDIT, BTR and BTRR plants 10P x 8P x A 12P x 10P x A 14P x 10P x A 8W x 6P x W x 6P x W x 8P x W x 10P x P x 10P x W x 10P x W x 12P x W x 12P x P x 14P x

63 GR SHROUDS CEMENT PASS-THROUGH GR SHROUDS CHAMP PT# BWD PT# 8 WAM to Truck, 36 long, GR SHROUDS 8 WAM to Truck, 48 long, GR WAM to Truck, 60 long, GR Pipe to Truck, 24 long, GR Cement boot for standard new style discharge head. 6 Pipe to Truck, 30 long, GR Cement boot for standard new style discharge head. 6 Pipe to Truck, 36 long, GR (22X36GR) Cement boot for standard new style discharge head. 6 Pipe to Truck, 48 long, GR (22X48GR) Cement boot for standard new style discharge head. SHROUDS, BOOTS & CLAMPS DM = Diaphragm Material. Vinyl coated canvass material, black on one side, gray on the other side. Used on Ross Plants for shroud material. GR = Gum Rubber. Used as a discharge shroud on Ross transit mix plants. Standard thickness is 1/8. RR = Red Rubber. Used as a gasket material on powder butterfly and piping connections. Also used to seal low pressure water piping connections. Typical thickness is 1/8. 61

64 SHROUDS GR SHROUDS FOR DISCHARGE HEADS CHAMP PT# BWD PT# 30 NEW STYLE DISCHARGE HEAD 88 x 18 Water Ring to Truck, (88X18GR) 18 long, GR; Agg boot for standard new style 30 discharge head. 88 x 24 Water Ring to Truck, X24GR 24 long, GR; Agg boot for standard new style 30 discharge head. 88 x 30 Water Ring to Truck, long, GR; Agg boot for standard new style 30 discharge head. 88 x 36 Water Ring to Truck, long, GR UNIPLANT & OLD-STYLE 24 DISCHARGE HEAD 65 x (65X18GR) 65 x x x x X30GR STANDARD OLD-STYLE DISCHARGE HEAD 68 x18 Water Ring to Truck, long, GR 68 x24 Water Ring to Truck, long, GR 67-1/2 act cir, 21-1/2 act ID 68 x30 Water Ring to Truck, long, GR 67-1/2 act cir, 30-1/2 act ID 68 x36 Water Ring to Truck, long, GR 67-1/7 act cir, 30-1/2 act ID 62

65 SHROUDS BANDIT B5 Discharge Head Aggregate Shroud GR Cement Shroud GR Cement Wt. Bin 10 x 10 Cement Fill DM Cement Discharge DM GR & DM SHROUDS FOR PLANTS BANDIT B12 Discharge Head 29 x 18 Aggregate Shroud GR x 18 Cement Shroud GR Cement Weigh Bin 8 W x 10 P x 8 Cement Fill DM Cement Discharge DM RUSTLER R3 Discharge Head Aggregate Shroud GR Cement Shroud GR Cement Weigh Bin Cement Fill DM Cement Discharge DM UNIROVER U1248 Cement Chute GR Plug Valve DM MISCELLANEOUS 78 x x

66 WATER SYSTEMS BADGER WATER METERS 4 Meter, Complete / Flange Mount Meter, Head Assembly, Complete (includes impeller housing assembly and transmitter head assembly, 4 Pole Impeller and Buna Seals) 4 Meter, Head Gasket Meter, Rotor & Spindle (Impeller) Meter, PFT-4E Transmitter Head Assy, Complete (includes circuit board, housing and Magneto-Resistive pickup). Fits 4 meters only. 4 Meter, Lower Housing Assembly for PFT-4E Transmitter board. Magneto-Resistive sensor ONLY is included (no circuit board, no upper cover, screws, or gaskets). Fits 2 and 3 meters. 4 Meter, Tetra seal Meter, Complete / Flange Mount Meter, Rotor & Spindle (Impeller) Meter, Head Assembly, Complete (includes Impeller housing assembly, Impeller, and 2-transmitter head assembly). Fits 2 and 3 meters. 2 Meter, Complete / Flange Mount Meter, Meter, Rotor & Spindle (Impeller) Meter, Head Assembly, Complete (includes Impeller housing assembly, Impeller, and transmitter head assembly). Fits 2 and 3 meters. 1-1/2 Meter with Transmitter

67 COMMON PARTS FOR ALL BADGER METERS WATER SYSTEMS PFT-4E Transmitter Cover, Clear Plastic PFT-4E Transmitter Cover, Gasket PFT-4E Transmitter (Board Only) & 3 Meter, PFT-4E Transmitter Assembly, Complete (includes circuit board, housing and Magneto-Restive pickup). Fits 2 and 3 meters. 2 & 3 Meter, Lower Housing Assembly for PFT-4E Transmitter board. Magneto-Resistive sensor ONLY is included (no circuit board, upper cover, screws, or gaskets). Fits 2 and 3 meters. 2 & 3 Meter, Head Gasket / Meter, Viton Gasket PS & 3 Meter, Tetra Seal WATER STRAINERS 4 Strainer, Complete / Flange Mount Screen 55-PS Strainer, Complete / Flange Mount Screen 55-PS Strainer, Complete / Flange Mount Screen 55-PS Strainer, Complete / Threaded Ends 55-PS Screen 55-PS Strainer, Complete / Threaded Ends 55-PS Screen PS Strainer, Complete / Threaded Ends Screen 55-PS

68 WATER SYSTEMS ATC 366, Water Controller (Simi Automatic) ATC COUNTERS ATC 376, Water Controller (Simi Automatic, scalable, and solid state) *Used on current manual panels. NOTES: 66

69 REFERENCE GUIDE ORDER FORM Fax this Completed Order Form to: Attn: Parts Literature & Support OR Mail to: TEREX ROADBUILDING ATTN: PARTS LITERATURE / CUSTOMER SERVICE PO BOX 1985 OKLAHOMA CITY, OK PLEASE PRINT CLEARLY ORDER FORM Your Name Title Quantity Requested Company Name Company Address City St Zip Country Phone ( ) FAX ( ) Please allow 3-4 weeks for shipping. There is no charge for these reference guides. TEREX ROADBUILDING PO BOX 1985 OKLAHOMA CITY, OK parts@terexrb.com (888)

70 NOTES: 68

71 THIS PAGE INTENTIONALLY LEFT BLANK (IBC)

72 TEREX ROADBUILDING PO BOX 1985 OKLAHOMA CITY, OK CUSTOMER SERVICE AND SUPPORT Call (888) Fax (405) Terex Corporation All Rights Reserved Terex is a registered trademark of Terex Corporation in the United States of America and many other countries. Products and services listed may be trademarks, service marks, or trade names of Terex Corporation and/or its subsidiaries in the United States of America and other countries, and rights are reserved.