Earth Leakage Circuit Breakers Accessories

Transcription

1 OFF OFF Earth Leakage Circuit s Accessories Variation of external accessory Insulation barriers The interphase barrier reinforces the insulation between terminals, while the earth barrier increases the insulation between the terminal and the mounting panel. See page /106 Mechanical interlock device The mechanical interlock device can be mounted onto two separate breakers to maintain a mutual ON or OFF condition. The device can also be locked with a padlock. See page /88 Interface barrier Earth barrier External operating handles There are two handles available in the series: the V type handle on panel mount and the N type handle on breaker mount. An extension shaft (sold separately) for the V type handle allows the distance between the handle and the breaker to be adjusted. The protective structure of the V type handle operation section conforms to IP54. oth handle types can be locked with a padlock conforming to IEC The panel cutout dimensions are the same for both handles. See page /91 TRIP OPEN/RESET TRIP ON N type ON ON andle locking cover OFF OPEN/RESET V type Motor-operating mechanism ELC A new drive structure in the motor operating mechanism speeds up drive operation to drastically reduce ON/OFF switching time from 2s to 0.1s. See page /85 Terminal covers Finger protection guards against shock from accidentally touching live terminals. Two types of terminal covers are availablelong type and short type. See page / Steel enclosures Enclosures are available in three typestwo with V-type handle which allows the operation from the outside, and other direct operating. See page /103 Long type Short type Information subject to change without notice /69

2 Motor-operated breakers Motor-operated breakers Description The breaker is fitted with a motor operating mechanism which enables ON, OFF and RESET operations to be carried out electronically by remote control. 4-pole motor operated breakers are also available. AF02-54 to 2AF CP-1214 AF AF and larger, 4-pole Types and ratings Motor rating Operating voltage Operating time Time rating Power source capacity SG33C/M SG53C/M, 53RC/M SG63C/M, 63RC/M EG33AC/M, 33C/M EG53AC/M, 53C/M EG63C/M EG102C/M, 103AC/M, 103C/M V DC /110V AC 200/220V AC 0.1s 15s per on-off operation 500VA SG103C/M SG103RC/M SG203C/M SG203RC/M EG203C/M 24V DC 48V DC V DC /110V AC 200/220V AC 2s 2.5s 30s 30s 50VA 50VA SG403C/M SG403RC/M SG603RC/M SG3RC/M EG403C/M EG603C/M EG3C/M /110V DC /110V AC 200/220V AC 2s 30s VA at /110V DC, /110V AC 200VA at 200/220V AC Ordering information Specify the following: 1. Type number 2. Motor operating voltage Dimensions, mm / Front mounting, front connection SG33C/M, SG53C/M, SG53RC/M, SG63C/M, SG63RC/M EG33AC/M, EG33C/M, EG53AC/M, EG53C/M, EG63C/M, EG102C/M, EG103C/M Wiring diagrams /110V AC, 200/220V AC, V DC 50 Mounting hole ø4.5 LC Insulation barrier (Except EG33AC/M, 53AC/M, SG33C/M) Operating handle M4 or ø5 Panel drilling DRIVE UNIT CONTROL CIRCUIT L C E 2 1 OFF ON Test button Terminal cover 4 Trip button Notes: Trip button operation can be carried out at right side of the breaker. IEC 35mm rail is not available. Power supply (Non polarity) Information subject to change without notice /85

3 Motor-operated breakers Dimensions, mm / Front mounting, front connection SG103RC/M, SG103C/M Wiring diagrams 24V DC, 48V DC, V DC Insuration barrier Detachable 50 R65 57 Panel drilling 2-M4 or ø Test lead wire Max /110V AC, 200/220V AC SG203C/M, SG203RC/M EG203C/M Insuration barrier Detachable Panel drilling R M4 or ø Test lead wire 142 Note: Interphase insulation barriers are standard provided for the front mounting type breakers of 50AF to 2AF Max C : Control relay for breaker closing T : Control relay for breaker open M : Motor Ca1-Cc : Relay terminal number for closing Ta1-Tc : Relay terminal number for open : Diode Z : Z-trap (Surge absorber) SS : ON/OFF changeover switch E, 1-5 : Terminal number for external wire connection : Resistor : LED : Silicon diode : Transformer : Capacitor AURS : Automatic reset switch (supplied on request) /86 Information subject to change without notice

4 Motor-operated breakers Dimensions, mm/front mounting, front connection Wiring diagrams/400 to 0AF SG403C/M, SG403RC/M EG403C/M Panel Panel drilling /110V AC, 200/220V AC, 50/60z Manual/ motor operation indicator olt M12 x 35 Test lead wire M M8 or ø7 /110V DC SG603RC/M, SG3RC/M EG603C/M, EG3C/M C A Panel Panel drilling Manual/ motor operation indicator olt M12 x 40 Test lead wire C 18 M ø7 C : Control relay for breaker closing R : Resistor T : Control relay for breaker open LS : Limit switch M : Motor AURS: Automatic reset switch (supplied on request) Amp. frame A (line side) (load side) C 600AF AF Dimensions for reference only. Confirm before construction begins. Type (ELC with motor operating mechanism) SG33C/M, SG53C/M, SG53RC/M EG33AC/M, EG33C/M, EG53AC/M, EG53C/M SG63C/M, SG63RC/M EG63C/M, EG102C/M, EG103AC/M, EG103C/M SG103C/M SG103RC/M SG203C/M, SG203RC/M EG203C/M SG403C/M, SG403RC/M, EG403C/M SG603RC/M, EG603C/M SG3RC/M, EG3C/M (kg) Information subject to change without notice /87

5 Mechanical interlocking device Mechanical interlocking devices Description These interlocking devices are mounted on the two separate breakers to prevent them from both being closed at the same time. They employ a slide method and are operated manually. These interlocking devices is possible to lock with a padlock (not supplied). They are designed for use when changing over power supplies. These can be mounted to 3 types of breakers: front-mounting frontconnection type, front-mounting rearconnection type (type X), and plug-in mounting type (type P). Interlock devices for flush mounting type breakers (type E, Y) are also available. M1 types Types and applicable breakers Type Z6M110C2 Z6M110C3 Z-M160C type SG33C SG53C, SG53RC SG63C, SG63RC SG403C, SG403RC EG32AC EG52AC EG33AC, EG33C EG53AC, EG53C EG63C EG102C EG103AC, EG103C EG403C Z-M170C SG603RC SG3RC EG603C EG3C /88 Information subject to change without notice

6 Mechanical interlocking device Dimensions, mm 30AF to EGAF C A Z6M110C2 Panel drilling 85 of slider mounting hole of breaker of breaker Padlock (Not supplied) 2-ø4.5 mounting hole 2-ø4.5 or M Z6M110C3 110 mounting hole of breaker 9 2-ø4.5 or M4 Type type Dimensions, mm A C (kg) Z6M110C2 EG32AC EG52AC Z6M110C3 SG33C SG53C SG63C SG53RC SG63RC EG33AC EG33C EG53AC EG53C EG63C EG102C EG103AC EG103C Notes: Z6M110C2 is not available for padlock. Applicable padlock(ø3.5) dimensions, mm ø3.5 ø Information subject to change without notice /89

7 Mechanical interlocking device Dimensions, mm of handle Panel drilling A' A C of slider F E of slider 10-M4 or ø5 Z6M140C J J N N Z-M160C, M170C J of handle J D G K P of breaker L of breaker Q Padlock (not supplied) Mounting screw (Provided) J' J' J' J' M6 or ø7 (Z-M140C: 8-M4 or ø5) Type type Dimensions, mm A (A') C D E F G J (J') K L (kg) Z-M160C SG403C SG403RC EG403C 355 (70) (70) Z-M170C SG603RC SG3RC EG603C EG3C 500 () () Note: Applicable padlock(ø3.5) dimensions, mm ø3.5 ø /90 Information subject to change without notice

8 Operating handles External operating handles Description Earth leakage circuit breaker handles are generally directly manual-operated but when mounted in motor control centers or on control panels they are sometimes required to be operated externally. To meet such applications FUJI offers the following three types of handles. N type handle This type has a knob handle directly attached to the breaker. It is easily fitted by cutting a hole in the panel, which is provided with a door interlock. They may be fitted to all breakers up to 0 ampere frame sizes. N type handles for SG/EG30AF to EGAF are UL508 listed. V type handle The V type handle may be fitted to breakers of up to 0AF. A separately sold extension shaft (Z-VS1)provides distance adjustment between the handle and breaker. Conformed to EN isolation function. Available for EN power breaking device. G type handle The G type handle is mounted on the panel, and also has a door-interlock. G type handle with a cylinder lock key is also available on request. G type handle with a padlockable handle lock plate is standard provided for circuit breaker of up to 2AF, and is optional for 400AF and larger. KK AF KK Z6N10C Z-N C Z6V10C Z-G10 N type handles V type handle G type handle N type handles Z-N N type handle on breaker V type handles Z6V C Decorative plate C V type handle on panel AF G type handles Z-G10 G type handle on panel Information subject to change without notice /91

9 Operating handles For breakers up to 0AF N type handles V type handles SG33C SG53C SG53RC SG63C SG63RC SG103C SG103RC SG203C SG203RC SG403C SG403RC SG603RC SG3RC EG32AC, 33AC, 33C EG52AC, 53AC, 53C EG63C EG103AC, 102C, 103C EG203C EG403C EG603C EG3C N type handle Z6N10C UL508 (File No. E216772) Z-N30C Z-N40C Z-N60C Z-N70C SG33C SG53C SG53RC SG63C SG63RC SG53RCUL SG103C SG103CUL SG103RC SG203C SG203CUL SG203RC V type handle EG32AC, 33AC, 33C Z6V10C EG52AC, 53AC, 53C UL489 EG63C (File No. E93289) EG103AC, 102C, 103C EG102CUL, 103CUL EG203C Z6V30C UL489 (File No. E93289) Z6V40C UL489 (File No. E93289) SG53RCUL SG103CUL SG203CUL SG403CUL EG102CUL, 103CUL N type handle UL489 (File No. E93289) Z6N10CP Z6N30CP Z6N40CP Z6N60CP SG403C SG403CUL SG403RC SG603RC SG3RC EG403C EG603C EG3C Z6V60C UL489 (File No. E93289) Z6V70C UL489 (File No. E93289) Notes: N type handles for up to 0AF can be padloked. Padlock is not provided. N type handles are not CE marked. For breakers other than N type handles series V type handles SGa104A, 104 SGa204A, 204 SGa404A EG104A G series G53 G103 G203 G403 G603 G3 N type handle Z-N35 Z-N50C Z-N60C Z-N70C N-13EA N-23EA N-6EA G series G203 G403 G603, G3 V type handle Z-V50C Z-V60C Z-V70C G type handles Type G53, 103 SGa104A, 104 SGa204A, 204 SGa404A EG104A Standard Z-G35C G-12A G-22A G-5A Cylinder key type Z-G35C-K G-12A-K G-22A-K G-5A-K /92 Information subject to change without notice

10 N type operating handles N type operating handles Operating instructions 1. ELC operation Close the door with the handle in the OFF position. Turn the handle to the ON position and the ELC will be ON. Turn the handle to the OFF position and ELC will be OFF. When the breaker trips, the handle moves to the TRIP position. To reset, move the handle to the RESET position. Fig. 1 Mounting screw For N10C, N30C ase plate 2. Door locking The door cannot be opened when the handle is in the ON, OFF or TRIP position, and can be opened only when the handle is in the OPEN position. The breaker cannot be ON when the door is open. If it is necessary to open the door with the breaker closed, turn the doorclose lock release screw counterclockwise using a screwdriver. 3. andle locking The handle can be locked in either the ON or OFF position when a padlock (not supplied) is used. Pull out the handle lock plate and fit your padlock to the plate. If the breaker trips while it is locked in the ON position, the handle moves to the TRIP position. For N40C Fig. 2 For N10C, N30C Installation Z6N10C to Z-N40C 1. Drilling and cutting the door Drill and cut the door. The dimensions for drilling and cutting are the same whether the ELC is installed horizontally or vertically. Decorative plate Retaining plate 2. Preparing a base plate (Fig. 1) Prepare a base plate to adjust breaker mounting position (base plate: not supplied). Front mounting, front connection type breakers can only be suitable for this handle. Drill the breaker mounting holes on the base plate. Fig. 3 Not correct 3. Fitting the N-handle mechanism and ELC to the base plate (Fig. 1) Commonly tighten the N-handle body and ELC to the base plate with the mounting screws. For N10C to N30C, tighten two mounting screws on a diagonal line, and for N40C, tighten four mounting screws. Assemble the driving unit so that the breaker handle engages the N handle arm. (Fig. 4) ELC ELC 4. Mounting the decorative plate Mount the decorative plate and the retaining plate to the door with screws provided. (Fig. 2) Adjust the position of the handle unit so that it does not tilt against the breaker. (Fig. 3) Space Fig. 4 andle window Decorative plate Decorative plate ELC handle N handle arm Information subject to change without notice /93

11 N type operating handles Installation Z-N60C, Z-N70C 1. Drilling and cutting the door Drill and cut the door. The dimensions for drilling and cutting are the same whether the ELC is installed horizontally or vertically. Fig Preparing a base plate (Fig. 1) Prepare a base plate to adjust breaker mounting position (base plate: not supplied). Front mounting, front connection type breakers can only be suitable for this handle. Drill the breaker mounting holes on the base plate. 3. Fitting the N-handle mechanism and ELC to the base plate (Fig. 1) Commonly tighten the N-handle body and ELC to the base plate with the four mounting screws. Assemble the driving unit so that the breaker handle engages the N handle arm. (Fig. 4) 4. Mounting the decorative plate Mount the decorative plate and the retaining plate to the door with screws provided. (Fig. 2) Adjust the position of the handle unit so that it does not tilt against the breaker. (Fig. 3) Fig. 2 Fig. 3 Fig. 4 ELC andle window Not correct Decorative plate N handle arm Decorative plate Space ELC ELC handle Type number nomenclature Z N C T R Installation lank: Vertically R: orizontally, right line side L: orizontally, left line side Door locking device lank: Provided T: Not provided asic type Z6N10C Z-N C N- EA Note: To order an N handle for front-mounting rear connection breakers, add -X to the type number, for plug-in mounting breakers, add -P to the type number. /94 Information subject to change without notice

12 N type operating handles Dimensions, mm Z6N10C to Z-N50C (Dust proof paking: Z-NP-1C, optional) Line Load 69 max. Z6N10CP, Z6N30CP, Z6N40CP (Dust proof paking: Z-NP-1C, optional) Line 69Max ± Door panel cutting Door hinge installation area OFF TRIP ON FA,EL handle C/L 4-ø15 FA,EL handle C/L andle C/L ø Padlock ø4 to ø / Panel Panel thickness 1.2 to Load type SG30C, SG50C, 50RC, SG60C, 60RC SG50RCUL EG30AC, 30C, EG50AC, 50C, EG60C EGAC, C, CUL SGC, RC, CUL andle type Z6N10C Z6N10CP Z-N30C Z6N30CP A Mounting screw M4 M4 85 (kg) type EG2C SG2C, 2RC, 2CUL G2 andle type Z-N40C Z-N40CP Z-N50C A Mounting screw M4 85 M4 1 (kg) Information subject to change without notice /95

13 OPEN Earth Leakage Circuit s N type operating handles Z-N60C, Z-N70C, Z-N60CP, Z-N70CP (Dust proof packing: Z-NP-2, optional) 150 Line Mounting screw Door panel cutting 96 I T R P O N Decorative plate Lock plate 4 -ø15 andle C/L 150 RESET O F F RELEASE and handle C/L and handle C/L ø type andle Mounting type screw (kg) SG400C, SG400RC Z-N60C M6 x SG400CUL Z-N60CP EG400C G400 SG600RC, SG0RC Z-N70C M6 x EG600C, EG0C Z-N70CP G600, G0 Dimensions, mm Z-N35 (Dust proof packing: Z-NP-1, optional) Door panel cutting Line 60 max Decorative plate Panel Panel thickness 1.2 to 3.2 Mounting screw 4 -ø15 of handle Load Lock lever 43 1 ±2 Packing(Optional) 78 ø90 of panel cutting Aux. handle (Only Z-N70C) Load Door hinge installation area P Panel thickness 1.6 to 3.2 Note: andle protection degree IP50 (IEC60529, JIS C 0920) (with the optional dust-proof packing) The handle cannot hold the door. Notes: 1. The N type handles are used with front mounting front connection type breakers. They are normally installed vertically. owever, it is possible to install them horizontally if required. In this case please specify so in your order. (Example) Specify as follows: Z-N C-R... Installed horizontally, the line positioned on the right side. Z-N C-L...Installed horizontally, the line positioned on the left side. 2. s use different size screws for the P-type (Plug-in) breakers Install the door hinge in the shaded area Install the door hinge in the shaded area. 30 : 0.45kg Dimensions for refernce only. Confirm before construction begins. Dimensions of N type handles for 4-pole: Contact FUJI. /96 Information subject to change without notice

14 V type operating handles V type operating handles, up to 2AF Operating instructions 1. ELC operation Close the door and turn the handle to the ON position and the breaker will be positioned at ON. When the breaker is interrupted automatically the handle will move to the TRIP position. To reset move the handle to the RESET position. 2. Door panel locking Turn the handle to the RESET position and the lock mechanism will be released thus allowing the door to be opened. The door cannot be opened when the breaker is positioned at ON. Fig. 1 Terminal cover Fig. 3 Padlock (Not supplied) Fig. 2 Fig. 4 Lock plate 3. andle locking The padlock can lock the handle in the OFF position. Locking ELC with the door open : Fig.1 Locking ELC with the door closed : Fig.2 Pull out the lock plate and lock the padlock. 4. Interlock release This type is provided with an interlock release screw. Turn this screw if it is necessary to open the door in the ON position. This release the lock and allows the door to be opened. When reclosing the door, make sure the handle of the breaker coincides with the position (ON or OFF) of the external handle position. Fig. 5 Installation Z6V10C to V50C 1. Drilling and cutting of the door panel Drill and cut the door panel as shown in the drawing. 2. Mounting of the ELC The distance between the backside of the door panel and breaker mounting plate should be the dimension "" shown in the drawing below. dimensions, mm (Fig.3) Z6V10C: Z6V30C: Z6V40C: Z-V50C: 144 For V10C, V30C For V40C Fig. 6 Latch Mounting screw Driving unit 3. Mounting the driving unit Set the breaker handle to the OFF position. Assemble the driving unit so that the breaker handle engages the V handle arm. (Fig.4 ) Secure the driving unit and breaker together to the mounting plate by tightening the four attached mounting screws. (Fig.5) 4. Mounting the handle unit Put the handle unit, cover holder, packing, and retainer in front of and behind the panel and tighten the screws temporarily as shown in Fig.6. Adjust the position of the handle unit so that it does not tilt against the breaker. (Fig.7) Put the handle of the handle unit in the OFF position and close the door. Check that the shaft engages the latch when the door closes. (Fig.8) Fig. 7 Retainer Door panel Packing Cover holder andle unit Interlock-release screw Fig. 8 Latch Shaft Information subject to change without notice /97

15 V type operating handles Dimensions, mm Z6V10C, 6V30C, 6V40C Door panel Door panel cutting 4-ø15 andle andle andle ø Panel thickness Z-V40V, V50C Door panel Optional shaft Z-VS1 X = - 96 Door hinge installation area OP O FT R O R E andle X Panel thickness The distance between the handle and breaker can be shortened by cutting the optional shaft. 120 Install the door hinge in the shaded area. type G series andle type Standard type With the optional shaft (X=154) Area in which the hinge with can be installed Mounting screw (kg) SG30C SG50C SG50RC SG60C SG60RC SG50RCUL EG30AC EG30C EG50AC EG50C EG60C EGAC EGC EGCUL Z6V10C to 0 60 M4 x 0.64 SGC SGRC SGCUL Z6V30C to 0 60 M4 x SG2C SG2RC SG2CUL EG2C Z6V40C to 0 60 M4 x G2 Z-V50C to M4 x Notes: andle protection degree IP54 (IEC60529, JIS C 0920) The handle cannot hold the door. /98 Information subject to change without notice

16 V type operating handles V type operating handles, 400AF to 0AF Operating instructions 1. ELC operation Close the door and turn the handle to the ON position and the ELC will be positioned at ON. When the ELC is interrupted automatically the handle will move to the TRIP position. To reset move the handle to the RESET position. 2. Door panel locking Turn the handle to the RESET position and the lock mechanism will be released thus allowing the door to be opened. The door cannot be opened when the breaker is positioned at ON. 3. andle locking The padlock can lock the handle in the OFF position. Locking ELC with the door open: Fig. 1 Locking ELC with the door closed: FIg Interlock release This type is provided with an interlock release screw. Turn this screw if it is necessary to open the door at the ON position. This releases the lock and allows the door to be opened. When reclosing the door, make sure the handle of the breaker coincides with the position (ON or OFF) of the external handle position. Installation Z6V60C, 70C 1. Drilling and cutting of the door panel Drill and cut the door panel as shown in the drawing. 2. Mounting of the ELC The distance between the backside of the door panel and ELC mounting plate should be the dimension as shown in Fig Mounting the driving unit Set the ELC handle to the OFF position. Assemble the driving unit so that the ELC handle engages the V handle arm. (Fig. 4) Secure the driving unit and ELC together to the mounting plate by tightening the four attached mounting screws. (Fig. 5) 4. Mounting the handle unit Put the handle unit, packing and retainer in front of and behind the door panel and tighten the screws temporarily as shown in Fig.6. Adjust the position of the handle unit so that it does not tilt against the ELC. (Fig. 7) Put the handle of the handle unit at OFF position and check the latch engages the keeper and close the door while holding the handle unit cover by hand. Final tightening the screws should be performed as keep the engaging position. (Fig. 8) Fig. 1 Fig. 2 Fig. 3 Fig. 4 Fig. 5 Fig. 6 Fig. 7 Type number nomenclature Fig. 8 Z6V C Mounting lank:front mounting, front connection X: Front mounting, rear connection P: Plug-in mounting asic type Z6V C Z-V C Note: To order a V handle for front-mounting rear connection breakers, add -X to the type number; for plug-in mounting breakers, add -P to the type number. Fuji Electric FA components & Systems Co., Ltd./D & C Catalog Information subject to change without notice /99

17 V type operating handles Dimnsions, mm Z6V60C, 6V70C, Z-V60C, V70C 150 Line Door panel cutting Optional shaft ( Z-VS2) Decorative plate Panel 4-ø10 andle O F F RESET OPEN I T R P O N RELEASE 150 and handle ø x Load 150 Lock plate 63 Mounting screw 112 The distance between the handle and breaker can be shortened by cutting the optional shaft. ( X = ) Door hinge installation area Panel thickness 1.6 to Install the door hinge in the shaded area. 200 G series andle type Standard type With the optional shaft Area in which the hinge with can be installed (kg) SG400C SG400RC SG400CUL EG400C Z6V60C 190±2 0±2 202 to G400 Z-V60C 2.2 SG600RC SG0RC EG600C EG0C Z6V70C 2.2 G600 G0 Z-V70C 2.2 Notes: andle protection degree IP54 (IEC60529, JIS C0920). The handle cannot hold the door. s use different size screws for the X type (rear connection) or P-type (Pulg-in) breakers. / Information subject to change without notice

18 G type operating handles G type operating handles Operating instructions 1. ELC operation Close the door and turn the handle to the ON position and the breaker will be positioned at ON. When the breaker is interrupted automatically the handle will move to the TRIP position. To reset move the handle to the RESET position. Installation ZG35C 1. Drilling and cutting of the door panel Drill and cut the door panel as shown in the drawing. 2. Mounting of the ELC The distance between the backside of the door panel and breaker mounting plate should be 1mm as shown in the drawing below. 2. Door panel locking Turn the handle to the OPEN position and the lock mechanism will be released thus allowing the door to be opened. The door cannot be opened when the breaker is positioned at ON. Panel Thickness 1.2 to 3.2 Mounting plate 3. andle locking The cylinder key can lock the handle in either the ON or OFF position. Even if it is locked at the ON position when the breaker trips, the handle will indicate TRIP. O C K O C K 44 1 ±2 Mount the breaker and the retaining plate commonly to the panel board. L L Retaining plate Locked Unlocked 4. Interlock release This type is provided with an interlock release screw. Turn this screw if it is necessary to open the door at the ON position. This releases the lock and allows the door to be opened. When reclosing the door make sure the handle of the breaker coincides with the position (ON or OFF) of that of the external handle. Adjusting screw 3. Fitting decoratire plate and handle Fit the decorative plate and handle mechanism to the door panel by means of the mounting screws as shown in the illustration. Type number nomenclature ZG CK Key lank: Without key K: With cylinder key Q: With padlocking device asic type Z-G C G- A Mounting screw Decorative legend plate OFF TRIP ON andle Door panel Lock lever andle mechanism 4. Adjusting the retaining plate Adjust the height of the retaining plate by means of adjusting screws. Fuji Electric FA components & Systems Co., Ltd./D & C Catalog Information subject to change without notice /101

19 G type operating handles Dimensions, mm Z-G35C, Z-G35C-K : 1.2kg G-22A, G-22A-K Retaining plate and supporter (Sold separately) 36±1 Line side of breaker Load side 73 Interlock release screw OPEN 2.3 max3.2.7±0.5 Retaining plate ON or OFF Door C± OPEN 150± ±1 49 ON OFF Door panel cutting 3-ø ø29 ø mounting hole 4-ø to 141 Adjustable height 3.2 of handle /102 Information subject to change without notice

20 Steel enclosures Pressed steel enclosures Description Z-type enclosures are available in three types two with V and G-type handle which allows the operation from the outside and other with the operating handle of the breaker extending from it to allow it to be directly switched ON or OFF from outside the enclosure. Enclosures with V and G-type handles are provided with a door interlocking mechanism which prevents the door from being opened in the ON condition. Knockout holes for wiring use are provided as shown in the diagram. (For G-type handles, contact FUJI.) AF90-7 AF CP Standard Dustproof Rainproof Type of enclosures type Enclosure G series Standard With V type handle Dustproof IP40 Rainproof IP54 * EG32AC EG52AC Z6C10C2 Z6CV10C Z6CW10C SG33C SG53C, SG53RC SG63C, SG63RC EG33AC, EG33C EG53AC, EG53C EG63C Z6C10C3 Z6CV10C Z6CW10C EG102C EG103C, EG103AC Z6CC3 Z6CVC Z6CWC SG103C, SG103RC Z6C30C3 Z-CV30C Z-CW30C SG203C, SG203RC EG203C G53 G103 Z-C35 Z-C40 Z-CV40C Z-CW40C G203 Z-C50 SG403C, SG403RC EG403C G403 Z-C60 Z-CV60C Z-CW60C SG603RC SG3RC EG603C EG3C G603 G3 Z-C70 Z-CV70C Ordering information Specify the following: 1. Type number of enclosures Information subject to change without notice /103

21 Steel enclosures Dimensions, mm Standard C With V type handle Z6CV10C to Z-CV40C A D : Z6CV10C : Z6CVC : Z-CV30C, 40C C D A E Mounting hole ø7 2 : Z6CVC to Z-CV40C Mounting hole ø7 : Z6CV10C ø9 : Z6CVC to Z-CV40C 2-øM lead hole OFF RESET TRIP ON E 17 : Z6CVC, Z-CV30C, Z-CV40C 2-ø23 lead hole Earth terminal M6 øm lead hole 4-øM lead hole G Earth terminal M6 I G Z-CV60C, 70C A D 269 C Connection method diagrams a b c Line Line Load d 5 E Line 2-øM lead hole Mounting hole ø12 2-ø28 lead hole Load 4-øM lead hole Load Load Line G Earth terminal M6 Type Z6C10C2 Z6C10C3 Z6CC3 Z6C30C3 Z-C35 Z-C40 Z-C50 Z-C60 Z-C70 Z6CV10C Z6CVC Z-CV30C Z-CV40C Z-CV60C Z-CV70C Connection a, b, c a, b, c, d A C D E G I M (Ø) (kg) , 35 30, 45 30, 45 30, 45 40, 55 40, 55 63, 78, , 35, 43 35, 52, 63 63, 78, /104 Information subject to change without notice

22 Terminal covers Terminal covers Description These terminal covers are used as guards to prevent accidental touch with live line terminations. These terminal covers can be fitted to either line or load side. Up to 2AF Short type Z-TS Snap-on fitting Transparent and black (Z6TS10C only), sealing possible Long type Z-T Crimp connection use Transparent and black (Z6T10C only), sealing possible 400AF and larger Long type Z-T Transparent Short type Long type Packing quantity : 2 pcs. type SG33C SG53C, SG53RC SG63C, SG63RC SG103C, SG103RC EG32AC EG52AC EG33AC, EG33C EG53AC, EG53C EG63C EG102C EG103AC, EG103C G series Terminal cover Short type Z6TS10C2 (lack) Z6TS10C2 (Transparent) Z6TS10C3 (lack) Z6TS10C3 (Transparent) Z-TS30-3 dimension (mm) (g) Terminal cover Long type Z6T10C2 (lack) Z6T10C2 (Transparent) Z6T10C3 (lack) Z6T10C3 (Transparent) Z-T30-3 dimension (mm) (g) SG203C, SG203RC EG203C G53 G103 G203 Z-TS35 Z-TS40 Z-TS Z-T35 Z-T40 Z-T SG403C, SG403RC EG403C G403 Z-T SG603RC SG3RC EG603C EG3C G603 G3 Z-T type SGa104A, SGa104 Terminal cover Long type A1-14 dimension (mm) 28 (g) 60 UL Listed type SG53RCUL SG103CUL EG102CUL EG103CUL Terminal cover Short type Z6TS10C3U (lack)* Z-TS30-3 (g) Terminal cover Long type Z6T10C3U (lack) Z-T30-3 (g) Terminal cover For flat terminal Z-TL30-3 (g) 110 SG203CUL Z-TS40 60 Z-T40 1 Z-TL SG403CUL Z-T Note: * Standard-provided Information subject to change without notice /

23 Insulation barriers Insulation barriers Description The interphase barriers are provided on frame size of 30AF to 400AF breakers for front mounting. The barriers are installed in the molded slots between terminals. The earth barrier is used to increase the insulation with the mounting plate surface when two crimp terminals are wired. Installation of these barriers after wiring is possible even when an external accessory is installed. Interphase barrier Earth barrier Interphase barrier type SG33C SG53C, 53RC SG63C, 63RC SG103C, 103RC SG103CUL EG32AC EG52AC EG102C EG33AC, 33C EG53AC, 53C EG63C EG103AC, 103C G series Interphase barrier Type Dimensions, mm A Z610C Z-30 Z630CU Packing quantity (g) Interphase barrier A SG203C, 203RC EG203C G53 G103 Z-35 Z SG203CUL Z640CU G203 Z SG403C, 403RC, 403CUL SG603RC SG3RC SGa204A, 204 SGa404A EG403C EG603C EG3C G403 G603 G3-43A -44A Earth barrier type SG33C SG53C, 53RC SG63C, 63RC SG103C, 103RC SG203C, 203RC EG32AC EG52AC EG33AC, 33C EG53AC, 53C EG63C EG102C EG103AC, 103C EG203C G series G53 G103 G203 Earth barrier Type Z6L10C2 Z6L10C3 Z-L35 Z-L40 Z-L50 Dimensions, mm* A 43 (50, 75) (30) 1 (75, ) 130 (90, 110) 190 (, 147) 190 (, 147) 43 (30) 70 (40) (50, 72) (50, 72) Packing quantity (g) Earth barrier A Note: * The value in parentheses is the dimensions after the barrier is cut. /106 Information subject to change without notice