Replacement parts to fit MASSEY FERGUSON CONTENTS IMPORTANT ORDERING INFORMATION

Transcription

1 CONTENTS SECTION 1 SECTION 2 SECTION 3 SECTION 4 SECTION 5 SECTION 6 SECTION 7 SECTION 8 SECTION 9 ENGINES...MF-1-1 through MF-1-72 ENGINE SYSTEMS...MF-2-73 through MF-2-97 ELECTRICAL...MF-3-97 through MF POWER TRAIN...MF through MF WHEELS AND ALES...MF through MF HITCH AND HYDRAULICS...MF through MF FORAGE AND HARVESTING...MF through MF IMPLEMENTS AND BEARINGS...MF through MF MISCELLANEOUS...MF through MF IMPORTANT ORDERING INFORMATION PART NUMBERS OEM numbers are used only for identification. All parts shown in this catalog are represented and sold as replacement parts only. Engine Kits To make ordering easier, we have four types of engine kits available. (1) Complete Engine Overhaul Kit (available for a limited number of tractor models) (2) Engine Overhaul Kit (EOK) (3) Basic Engine Kit (BEK) (4) Basic In-Frame Kit (BIF) EOKs and BEKs are available for most of the tractor models that we service with engine parts. Section 1 pages list the contents and also parts that can be ordered individually. Piston & Ring Sets For ease of ordering, our PK kits contain pistons, piston pins, pin retainers, piston rings, cylinder sleeves & sleeve seals(where noted) for one complete engine. Our PRS kits contain piston rings for one complete engine. Unless otherwise noted, we make no representation that our piston rings fit pistons available from other suppliers. We are aware of some interchangeability of tractor engine parts for other Massey Ferguson applications (combine, forklifts, industrial tractors & power plants); some of these applications are listed on the engine pages, otherwise no attempt is made to suggest other applications. Alphabetical Index Follows MF-I

2 ALPHABETICAL INDE A Actuator, Brake, 109 Adapter, Engine Block Heater, 92 Air Cleaner Bowl, 80 Air Cleaner Cap, 82 Air Cleaner Hose, 82 Air Cleaner Oil Cup, 82 Air Filter, 81 Alignment Tool, Clutch, 113 Alternator, 105 Bearing, 106 Brush, 106 Conversion Kit, 105 Diode Trio, 106 Pulley, 106 Repair Kit, 106 Ammeter, 106 Anchor Pins, 150 Arm, Steering, 134 Arm, Three Point Lift, 142, 144, 147 Armrest, Seat, 199 Auger Finger, 174 Auger Finger Guide, 174 Axle Bearing, Front Spindle, 137 Bearing, Spindle Thrust, 137 Bearings, Front, 136, 138 Bolt, 131 Bushing, Front Pivot, 131 Bushing, Front Spindle, 137 Front, 135 Gasket, Rear Housing, 124 Hub, 139 Knee, Front, 135 Pin, Front Pivot, 131 Seal, Rear, 124 Seals, 122, 124, 180 Seals, Front, 138 Seals, Front Hub, 138 Sleeve, Rear Speedi, 124 Sleeve, Wear, Front, 136, 139 Spindle, Front, 135 to 136 Tie Rod Ends, Front, 131 to 132 B Backrest, Seat, 199 Bale Counter, 172 Baler Parts Bearing, Wire Guide, 171 Bolt, Bale Chamber Shear Blade, 171 Counter, Bale, 172 Shearbolt, 171 Switch, Twine Tie, 171 Teeth, Pickup, 170 Ball Bearing, 177 Ball, Disc Brake, 109 Ball, Lift Arm, 144 to 145 Battery Bolt, 104 Cable, 104 Door, 190 Ground Strap, 104 Bearings Alternator, 106 Ball, 177 Carrier, Clutch Release, 117 Clutch, Pilot, 117 Clutch, Release, 117 Combine, 172, 178 Disc Harrow, 179 Disc Harrow Wheel Kit, 180 Flanges, 179 Generator, 104 Guide, Baler Wire, 171 Mower, 170 PTO Shaft, 125 to 126 Pump, Hydraulic Lift, 155 Shaft, Steering, 127 Sickle Head, 168 Spindle, Thrust, 137 Straw Walker, 175 Tapered Cups & Cones, 123 to 124, 127, 170, 180 Thrust, Spindle, 137 Thrust, Steering Gear, 127 Transmission, 119, 123 to 124 Wheel, Disc, 180 Wheel, Front, 136, 138 Wheel, Gauge, 177 Belts Alternator, 86 Combine, 86, 176 Fan, 86 Generator, 86 Mower, 170 Block Heater, 92 Block, Hydraulic Pump Cam, 153 to 154 Blower Assembly Massey Ferguson, 187 Blower Motor Massey Ferguson, 187 Blower Switch Massey Ferguson, 184 Bolt Axle, 131 Bale Chamber Shear Blade, 171 Battery, 104 Clutch Release Lever, 113 Differential Ring Gear, 121 Front Wheel, 140 Guard, 168 MF-II

3 Bolt (continued) Hydraulic Pump Drive, 157 Sickle Head, 168 Swinging Drawbar, 152 Wheel, 139 to 140 Bowl, Air Cleaner, 80 Bracket Bumper, 187 Hood Side Panel, 190 Three Point Stabilizer, 149 to 150 Valve Handle, 163 Brakes Actuators, 109 Ball, Disc, 109 Cable, 110 Cylinder, 108 Discs, 109 Drum, 108 Rod, 110 Seal, Rod, 110 Shoes, 108 Spring, 110 Brush, Alternator, 106 Brush, Generator, 104 Bulb, Light, 106 to 107 Bumper Bracket, 187 Bumper, Front, 187 Bushing Carburetor Throttle Shaft, 74 Clutch Shaft, 118 Combine Slip Clutch, 175 Corn Head, 172 Front Axle Pivot, 131 Hydraulic Pump, 153 Hydraulic Pump Drive Plate, 158 Link Pin Adaptor, 145, 148 Spindle, 137 Steering Shaft, 128 Sway Chain Eyebolt, 151 Three Point Lift Shaft, 142 Three Point Stabilizer, 151 C Cab Floormat, 193 Cable, Battery, 104 Cable, Brake, 110 Cable, Tachometer, 84 Cam & Weight, Distributor, 97 Camshaft Gear, 71 Camshaft, Engine, 71 Cap, Air Cleaner, 82 Cap Distributor, 97 to 98 Fuel Tank, 76 Hub, 138 Oil Filler, 83 Radiator, 88 Steering Wheel, 127 Carburetor, 73 Bushing, Throttle Shaft, 74 Elbow, Inlet, 75 Float, 75 Kits, 73 to 74 Carrier, Clutch Release Bearing, 117 Chain Combine Drive, 175 Connector Links, 173 Gathering, Corn Head, 173 Half Links, 173 Offset Links, 173 Clamp Exhaust, 94 Hydraulic Coupler, 159 Rear Wheel, 140 Clevis, Lift Arm Stay Chain, 151 Clevis, Swinging Drawbar Mount, 151 Clutch Alignment Tool, 113 Bearing, Pilot, 117 Bearing, Release, 117 Bolt, Release Lever, 113 Bushing, Combine Slip Clutch, 175 Bushing, Shaft, 118 Carrier, Bearing, 117 Cover, 111, 115 Disc, 112, 116, 119 Disc, PTO, 112 Disc, Slip Clutch, 171 Kits, Complete, 111 Lever, Release, 113, 115 Link, Release Lever, 113 Nut, Release Lever, 113 Pin, 113 Pin, Release Lever Pivot, 113 Pin, Release Lever Retaining, 113 Plate, Friction, 121 Pressure Plate, 111, 116 Slip, Combine, 175 Spring, 113, 115 to 116, 118 Washer, Pressure Plate Spring, 113 Coils, Ignition, 98 Combine Parts Bearing, Straw Walker, 175 Bearings, 172, 178 Belts, 86, 176 Blades, Sickle, 166 Bushing, Slip Clutch, 175 Chain, Corn Head Gathering, 173 Chain, Drive, 175 Clutch, Slip, 175 Finger, Auger, 174 Flute, Corn Head, 172 Guards, Sickle, 169 Guide, Auger Finger, 174 Holder, Auger Finger, 174 Idler, Chain, 175 MF-III

4 Combine Parts (continued) Idler, Wood Block Chain, 175 Knife, Straw Chopper, 174 Paddle, 174 Rivet, Sickle, 167 Seal, Engine Air Intake, 173 Section, Sickle, 166 to 167 Spacer, Corn Head, 172 Teeth, Pickup, 170 Tine, Pickup Reel, 173 Compressor Massey Ferguson, 183 Condenser, Distributor, 97 to 98 Cone, Hood Nose, 188 Connector, Sickle Head, 168 Cooling Systems Caps, Radiator, 88 Drain, Radiator, 88 Fan, Blade, 88 Gaskets, 86 Hoses, 90 to 91 Kits, Water Pumps, 86 Pulley, Water Pumps, 86 Radiators, 89 Sender, Water Temperature, 84 Thermostats, 90 Water Pumps, 85 Counter, Bale, 172 Coupler Clamp, Hydraulic, 159 Female Hydraulic, 159 Hydraulic Pump Drive, 157 Male Hydraulic, 159 Cover, Distributor Dust, 98 Cover, PTO, 125 Crankshaft Gear, 71 Crankshaft, Engine, 71 Cuff, Lift Arm, 145 Cultivator Gauge Wheel, 177 Cultivator Sweep Washer, 177 Cup, Air Cleaner Oil, 82 Cut-out, Generator, 104 Cylinder Head, Engine, 72 Cylinder Ball Joint End, 129 Brakes, 108 Hydraulic Three Point Lift, 143 Side Link, 165 Steering, 128 Top Link, 165 D Decals, 197 Deflector, Ear Corn, 173 Detent, Hydraulic Valve, 163 Differential Bolt, Ring Gear, 121 Coupler, Pinion Shaft, 121 to 122 Differential (continued) Nut, Ring Gear, 121 Pinion, 123 Resin Kit, 121 Disc Bearings, 179 Brake, 109 Clutch, 112, 116, 119 Clutch, Slip, 171 PTO Clutch, 112, 116 PTO Friction, 119 Quadrant Friction Plate, 143 Distributor, 97 Caps, 97 to 98 Coil, 98 Dust Cover, 98 Rotor, 97 to 98 Door, Battery, 190 Drag Link Ends, 131 to 132 Drain Cock, Radiator, 88 Drawbar Bolt, Swinging, 152 Clevis Mount, 151 Drawbar, 151 Hanger, 151 Pin, 151 Pivot Pin, 152 Stay Arm, 151 Three Point, 151 Drum, Brake, 108 Dust Cap, Wheel, 138 E Ear Corn Deflector, 173 Elbow, Exhaust, 92 Electrical Adapter, Block Heater, 92 Alternators, 105 Ammeter, 106 Bolt, Battery, 104 Brush, Alternators, 106 Brush, Generator, 104 Bulb, Light, 106 to 107 Cables, Battery, 104 Cables, Ground Strap, 104 Cam & Weight, Distributor, 97 Cap, Distributor, 97 to 98 Clip, Neutral Safety Switch, 101 Coils, Ignition, 98 Condenser, 97 to 98 Cover, Distributor Dust, 98 Cut-out, Generator, 104 Diode, Alternator, 106 Distributor, 97 Drive, Starters, 103 Electronic Ignition Kit, 98 Heater, Engine, 92 Heater, Engine Manifold, 91 MF-IV

5 Electrical (continued) Holder, Fuse, 106 Housing, Starter Drive, 103 Key, Ignition Switch, 100 Kit, Alternator Conversion, 105 Kit, Alternator Repair, 106 Kit, Tune-up, 98 to 99 Light, Warning, 107 Points, 97 to 98 Pulley, Alternator, 106 Rectifier, Alternators, 106 Regulator, Voltage, 104, 106 Rotor, Distributor, 97 to 98 Sender, Fuel Tank, 76 Solenoid, Starter, 102 Spark Plugs, 98 Starter Drive, 103 Starters, 102 Switch, Ignition, 100 Switch, Light, 101 Switch, Neutral Safety, 101 Switch, Oil Pressure, 83 Switch, Water Temperature Sending Unit, 84 Wires, Spark Plug, 97 End Lift Arm, 144 to 145 Lift Arm Repair, 144 Top Link, 147 Engines Belts, 86 Camshaft, 71 Caps, Fuel Tank, 76 Caps, Oil Filler, 83 Caps, Radiator, 88 Clamps, Mufflers, 94 Crankshaft, 71 Elbow, Exhuast, 92 Fan, Cooling, 88 Filters, Air, 80 to 81 Filters, Fuel, 80 Filters, Oil, 82 Gaskets, Manifold, 93 Gauge, Oil Pressure, 83 Gauge, Water Temperature, 84 Gear, Camshaft, 71 Gear, Crankshaft, 71 Governor, 83 Head, Cylinder, 72 Heater, Block, 92 Heater, Manifold, 91 Kit, See page I to V for complete application listing, 1, 3 to 70 Manifolds, 92 Mufflers, 93 to 96 Oil Level Indicator, 83 Pulley, Water, Repair, 86 Pump Repair Kit, Oil, 72 Pump, Oil, 72 Pumps, Water, 85 Engines (continued) Pumps, Water, Repair Kit, 86 Seal, Combine Air Intake, 173 Thermostat, 90 Exhaust System Caps, Rain, 94 Clamps, 94 Elbow, 92 Gaskets, Manifold, 93 Heater, Manifold, 91 Manifolds, 92 Mufflers, 93 to 96 Rain Caps, 94 Expansion Valve Massey Ferguson, 186 Eyebolt, Lift Arm Sway Chain, 151 Eyebolt, Sway Chain, 151 F Fan, Cooling, 88 Fender, 190, 192 Filters Air, 80 to 81 Fuel, 80 Oil, Engine, 82 Oil, Hydraulic, 119, 121, 158 to 159 Power Steering, 130 Finger, Auger, 174 Flange, Hydraulic Pump Drive, 157 Flangettes, Bearing, 179 Float, Carburetor, 75 Floormat, 193 Flute, Corn Head, 172 Flywheel Ring Gear, 103 Fork, Leveling Shaft, Three Point, 142 Fork, Three Point Leveling, 141 Fuel Gauge, 76 Fuel Injector Pumps, 78 Fuel Systems Bushing, Carburetor Throttle Shaft, 74 Caps, Fuel Tank, 76 Carburetors, 73 Filter, Air, 80 to 81 Filter, Fuel, 80 Floats, Carburetor, 75 Gauge, 76 Injector Nozzle, 79 Injector Pumps, 78 Kits, Carburetors, 73 to 74 Needle & Seat, 75 Nozzle, Injectors, 79 Pumps, Lift, 77 Sediment Bowl Assembly, 75 Sender, Tank, 76 Shut-Off, Tank, 76 Strainer, Carburetor Inlet, 75 Tank Webbing, 76 Valve, Float, 75 MF-V

6 Fuel Systems (continued) Valve, Shut-off, 75 Fuse Holder, 106 Fuse, Limiter Massey Ferguson, 185 G Gas Struts, 194 Gaskets Axle, Rear Housing, 124 Exhaust, 93 Hydraulic Lift Cover, 143 Hydraulic Pump Base, 143 Hydraulic Pump Valve Chamber, 143 Hydraulic Quadrant, 143 Transmission, 119, 143, 153 Water Outlet, 86 Gauge Wheel, 177 Gauges Ammeter, 106 Cable, Tachometer, 84 Fuel, 76 Fuel Tank Sender, 76 Oil Level Indicator, Engine, 83 Oil Level Indicator, Hydraulic, 152 Pressure, Engine Oil, 83 Tachometer, 84 Temperature, Water, 84 Gear Camshaft, Engine, 71 Crankshaft, Engine, 71 Lift Leveling Box, 141 Shift Knob, 118 Starter Ring, 103 Generator Bearing, 104 Brush, 104 Cut-out, 104 Governor, 83 Grassboard, Sickle Mower, 170 Grill, 187, 189 Grommet, Steering Column, 127 Guard Bolt, 168 Guard, Sickle, 169 Guide, Auger Finger, 174 H Handle Kit, Valve, 162 Handle, Hydraulic Valve, 162 to 163 Hanger, Swinging Drawbar, 151 Hardener, Paint, 196 Head Connector, Seals, 168 Head, Engine Cylinder, 72 Head, Sickle, 168 Heater Adapter, Engine Block, 92 Heater, Engine Block, 92 Hitch Pins, 152 Hold Down, Sickle Knife, 169 Holder, Auger Finger, 174 Hood Decals, 197 Engine, 190 Latch, 104, 190 Nose Cone, 188 Side Panel, 190 Trim, 189 Hose Air Cleaner, 82 Hydraulic Assemblies, 161 Radiator, 90 to 91 Housing, PTO Pinion Shaft, 122 Hub Cap, 138 Hydraulic Bearing, Lift Pump, 155 Block, Pump Cam, 153 to 154 Bolt, Pump Drive, 157 Bracket, Valve Handle, 163 Bushing, Pump, 153 Bushing, Pump Drive Plate, 158 Chamber Kit, Pump, 153 Clamp, Coupler, 159 Coupler Kit, 160 Coupler, Pump Drive, 157 Couplers, Female, 159 Cylinder, Side Link, 165 Cylinder, Three Point Lift, 143 Cylinder, Top Link, 165 Detent, Valve, 163 Disc, Quadrant Friction Plate, 143 Filter, 119, 121, 158 to 159 Flange, Pump Drive, 157 Gasket, Lift Cover, 143 Gasket, Pump Base, 143 Gasket, Pump Valve Chamber, 143 Gasket, Quadrant, 143 Handle, 162 to 163 Handle Kit, Valve, 162 Hose Assembly, 161 Kit, Control Valve, 155 Kit, Cylinder Seal, 159 Kit, Pump Repair, 153 to 154 Kit, Top and Side Link Cylinder Seal, 165 Kit, Valve Spool Return, 163 Kits, Valve, 160 to 161, 163 Knob, Valve Handle, 162 Nut, Pump Drive, 157 O-Rings, 119, 152, 154 to 156 Oil Dipstick, 152 Piston, Lift, 153, 155 Piston, Pump, 155 Piston, Three Point Lift, 143 Plate, Pump Drive, 158 Plug, Coupler Dust, 159 Power Beyond Plug, Valve, 163 Pumps, 153, 156 Ring, Three Point Lift Piston, 155 MF-VI

7 Hydraulic (continued) Rings, Piston, 143 Seal Kit, Valve, 163 Seal, Cylinder, 159, 165 Shaft, Pump, 158 Shaft, Three Point Lift, 142 Stop, Quadrant Lever, 144 Tips, Male, 159 Valve, 162 Valve, Isolator, 160 Valve, Lift Cylinder Pressure Relief, 156 Valve, Pressure Relief, 156 Valve, Pump Chamber Assembly, 154 Valve, Pump Control, 155 Valve, Pump Releif, 156 I Ignition Kit, Electronic, 98 Ignition Switch, 100 Injector Nozzle Tip, 79 Injector Nozzle, Fuel, 79 Injector Pumps, Fuel, 78 K Key, Ignition Switch, 100 Kits Alternator Conversion, 105 Clutch, 111 Coupler, Hydraulic, 160 Cylinder Seal, 159 Electronic Ignition, 98 Engine, See page I to V for complete application listing, 1, 3 to 70 Hydraulic Lift Cover Repair, 143 Hydraulic Pump Repair, 153 to 154 Hydraulic Pump, Chamber, 154 Hydraulic Remote Valve, 159 Ignition Tune-Up, 98 to 99 Over-Running Coupler Repair, 126 Pump Control Valve, 155 Pump Seal, 130 Seal, Steering Cylinder, 128 Steering Seal, 129 to 130 Top and Side Link Cylinder Seal, 165 Valve Spool Return, Hydraulic, 163 Valve, Hydraulic, 160 to 161, 163 Knife Clip, 169 Knife, Straw Chopper, 174 Knob, Hydraulic Valve Handle, 162 Knob, Transmission Gear Shift, 118 L Latch, Hood, 104, 190 Leveling Box Assembly, Three Point, 141 Lever, Clutch Release, 113, 115 Lift Arm End, Three Point, 144 to 145 Lift Arm, Three Point, 142, 144, 147 Lift Cover Repair Kit, 143 Light, Warning, 107 Light Bulb, 106 to 107 Switch, 101 Limiter Fuse Massey Ferguson, 185 Linch Pin, 149, 152 Link, Clutch Release Lever, 113 Link, Three Point Lift, 141 Links, Chain Connector, 173 Links, Offset Chain Connector, 173 Lower Link Pins, 150 Lug Bolt, 139 to 140 M Manifold, 92 Massey Ferguson Blower Assembly, 187 Blower Motor, 187 Blower Switch, 184 Compressor, 183 Expansion Valve, 186 Limiter Fuse, 185 Pressure Switch, 184 Receiver Drier, 185 Thermostatic Switch, 184 Mower Parts Bearings, 170 Belts, 170 Bolt, Guard, 168 Bolt, Sickle Head, 168 Clip, Knife, 169 Connector, Sickle Head, 168 Grassboard, 170 Guards, Disc Mower, 169 Guards, Sickle Mower, 169 Head, Sickle, 168 Hold Down, Knife, 169 Knives, Sickle, 166 Nut, Sickle Guard, 168 Pitman Wood, 169 Plate, Wear, 168 to 169 Rivet, Sickle, 167 Section, Sickle, 166 to 167 Spacer, Sickle Head, 168 Strip, Hold Down Wear, 169 Vise, Sickle Section Rivet, 168 Washer, Sickle Guard, 168 Mufflers, 93 to 96 N Needle & Seat, Carburetor, 75 Nozzle, Fuel Injector, 79 Nozzle, Injector, 79 Nut Clutch Release Lever, 113 Differential Ring Gear, 121 Front Wheel, 139 Hydraulic Pump Drive, 157 MF-VII

8 Nut (continued) Sickle Guard, 168 Stabilizer Pin, 149, 151 Wheel, 140 Wheel Clamp Lock, 138 O O-Rings, 119, 152, 154 to 156 Oil Cup, Air Cleaner, 82 Oil Cap, Filler, 83 Engine Pump Repair Kit, 72 Filter, Engine, 82 Gauge, Pressure, 83 Indicator, Level, 83, 152 Pump, Engine, 72 Switch, Pressure, 83 Over-Running Coupler Repair, 126 P Paddle, Combine, 174 Paint Aluminum, 195 Black, 195 Hardener, 196 OEM Colors, 195 Primer, 196 White, 195 Panel, Hood Side, 190 Pickup Teeth, Baler, 170 Pin Anchor, 150 Clutch, 113 Clutch Release Lever Pivot, 113 Clutch Release Lever Retaining, 113 Drawbar, 151 Front Axle Pivot, 131 Hitch, 152 Linch, 149, 152 Lower Link, 150 Stabilizer, 144, 149 to 151 Swinging Drawbar Pivot, 152 Top Link, 150 Piston, Hydraulic Lift, 153, 155 Piston, Three Point Lift, 143 Pitman Wood, 169 Plate, Hydraulic Pump Drive, 158 Plate, Sickle Wear, 168 to 169 Plug, Hydraulic Coupler Dust, 159 Points, Distributor, 97 to 98 Power Beyond Plug, Hydraulic Valve, 163 Power Steering Plate, 130 Pressure Plate, 111, 116 Pressure Switch Massey Ferguson, 184 Primer, 196 PTO Bearing, Shaft, 125 to 126 PTO (continued) Clutch Disc, 112, 116 Coupler, Over-Running, 126 Cover, 125 Disc, Clutch, 112 Housing, Pinion Shaft, 122 Kit, Over-Running Coupler Repair, 126 Plate, Clutch, 119 Shaft, Conversion, 125 Shaft, Pinion, 122 Sleeve, Shaft Retainer, 125 Pulley, Alternator, 106 Pulley, Water Pump, 86 Pump Control Valve, 155 Pumps Bushing, Hydraulic Drive Plate, 158 Cam Block, Hydraulic, 153 to 154 Chamber Kit, Hydraulic, 153 Coupler, Hydraulic Drive, 157 Flange, Hydraulic Drive, 157 Fuel Lift, 77 Hydraulic, 153, 156 Hydraulic Chamber Repair, 154 Hydraulic Repair Kit, 153 Kit, Hydraulic Repair, 154 Oil, Engine, 72 Plate, Hydraulic Drive, 158 Repair Kit, Engine Oil, 72 Shaft, Hydraulic, 158 Steering, Power, 129 Valve, Hydraulic Chamber Assembly, 154 Water, Engine, 85 Water, Repair Kit, 86 R Radiator, 89 Cap, 88 Drain, 88 Hose, 90 to 91 Rain Cap, Exhaust, 94 Receiver Drier Massey Ferguson, 185 Rectifier, Alternator, 106 Resin Kit, Differential, 121 Rim Clamp, Rear, 140 Front Wheel, 139 Rear Wheel, 140 Ring Gear, Starter, 103 Rings, Hydraulic Lift Piston, 143 Rings, Three Point Lift Piston, 143, 155 Rivet, Sickle, 167 Rod and Yoke, Three Point Leveling, 142 Rod End, Steering Cylinder, 128 Rod, Brake, 110 Rod, Lift Leveling, 141 Rotor, Distributor, 97 to 98 MF-VIII

9 S Screw, Power Adjust Stop, 140 Seal Kit, Steering Cylinder, 128 Seal, Front Axle, 138 Seals, 119, 122, 124 to 125, 136, 138 Axle, Rear, 124 Brake Rod, 110 Head Connector, 168 Sleeve, Implement Wheel, 180 Sleeve, Wear, Front Axle, 136, 139 Valve, Hydraulic, 163 Seat Armrest, 199 Backrest, 199 Cover, Cushion, 198 to 199 Cushion, 198 to 199 Inlay, Cushion, 198 Riser, 199 Seat Assembly, 198 Section, Sickle, 166 to 167 Sediment Bowl Assembly, 75 Sending Unit, Fuel Tank, 76 Shaft Conversion, PTO, 125 Hydraulic Pump, 158 Leveling Three Point, 141 to 142 Lift Arm Pivot, 144 PTO, 125 PTO Pinion, 122 Steering, 127 Three Point Lift, 142 Shearbolt, 171 Sheet Metal Bracket, Bumper, 187 Bracket, Side Panel, 190 Bumpers, 187 Cone, Hood Nose, 188 Door, Battery, 190 Fender, 190, 192 Grill, 187, 189 Hood, 190 Latch, Hood, 104, 190 Panel, Side, 190 Trim, Hood, 189 Shoe, Brake, 108 Shut-Off, Fuel, 76 Sickle Guard Bolt, 168 Guard Nut, 168 Guard Washer, 168 Head, 168 Head Bearing, 168 Head Bolt, 168 Head Connector, 168 Head Spacer, 168 Hold Down Wear Strip, 169 Knife Assembly, 166 Knife Clip, 169 Sickle (continued) Pitman Wood, 169 Repair Vise, 168 Rivets, 167 Section, 166 to 167 Wear Plate, 168 to 169 Sleeve, PTO Shaft Retainer, 125 Slip Clutch Disc, 171 Slip Clutch, Combine, 175 Solenoid, Starter, 102 Spacer, Sickle Head, 168 Spark Plug Wires, 97 Spark Plugs, 98 Spindle, Front Axle, 135 to 136 Spring Brakes, 110 Clutch, 113, 115 to 116, 118 Multi-Power Piston Return, 119 Sprocket, Chain Idler, 175 Stabilizer Pins, 149 to 150 Stabilizer, Three Point Hitch, 149 to 150 Starter, 102 Drive, 103 Housing, Drive, 103 Ring Gear, 103 Switch, Neutral Safety, 101 Starter Solenoid, 102 Starter Drive, 103 Housing, Drive, 103 Ring Gear, 103 Switch, Neutral Safety, 101 Steering Arm, 134 Axle, Front, 135 Bearing, Steering Gear Thrust, 127 Bushing, Shaft, 128 Bushing, Spindle, 137 Cap, Steering Wheel, 127 Cylinder, 128 Drag Link End, 131 to 132 End, Power Steering Cylinder, 129 Filters, 130 Grommet, Column, 127 Kit, Cylinder, 128 Kit, Pump Seal, 130 Plate, Power Steering, 130 Pump Seal Kit, 130 Pumps, 129 Rod End, Cylinder, 128 Seal Kit, 129 to 130 Shaft, Steering Wheel, 127 Spindle, Front, 135 to 136 Tee, Line, 131 Tie Rod, 132 Tie Rod Ends, 131 to 132 Wheel, 127 Stop, Hydraulic Quadrant Stop, 144 MF-I

10 Stop, Power Adjust Wheel, 140 Strainer, Fuel, 75 Strip, Sickle Hold Down Wear, 169 Struts, Gas, 194 Sway Chain, Lift Arm, 151 Swinging Drawbar, 151 Switch Activator, Tine Tie, 171 Clip, Neutral Safety, 101 Ignition, 100 Light, 101 Neutral Safety, 101 Oil Pressure, 83 Water Temperature Sending Unit, 84 Switches Blower, Massey Ferguson, 184 Pressure, Massey Ferguson, 184 Thermostatic, Massey Ferguson, 184 T Tachometer, 84 Tachometer Cable, 84 Tank Webbing, Fuel, 76 Tee, Steering Line, 131 Teeth, Baler Pickup, 170 Teeth, Combine Pickup, 170 Thermostatic Switch Massey Ferguson, 184 Thermostats, 90 Three Point Hitch Arm, Lift, 142, 144, 147 Ball, Lift Arm, 144 to 145 Bracket, Stabilizer, 149 to 150 Bushing, Lift Shaft, 142 Bushing, Link Pin Adaptor, 145, 148 Bushing, Stabilizer, 151 Bushing, Sway Chain Eyebolt, 151 Clevis, Stay Chain, 151 Cuff, Lift Arm, 145 Cylinder, Hydraulic Lift, 143 Drawbar, 151 End, Lift Arm, 144 to 145 End, Lift Arm Repair, 144 End, Top Link, 146 to 148 Eyebolt, Sway Chain, 151 Fork, Leveling, 141 to 142 Gear, Leveling Box, 141 Kit, Lift Cover Repair, 143 Leveling Box Assembly, 141 Link, 141 Nut, Stabilizer Pin, 149, 151 Pin, Anchor, 150 Pin, Lower Link, 150 Pin, Stabilizer, 144, 149 to 151 Pin, Top Link, 150 Piston, Hydraulic Lift, 153, 155 Piston, Lift, 143 Ring, Lift Piston, 155 Three Point Hitch (continued) Rings, Lift Piston, 143 Rod and Yoke, Leveling, 142 Rod, Leveling, 141 Seal, Top and Side Link Cylinder, 165 Shaft, Leveling, 141 to 142 Shaft, Lift, 142 Shaft, Lift Arm Pivot, 144 Stabilizer, 149 to 150 Stay, Drawbar, 151 Sway Chain, 151 Top Link, 146 to 147 Washer, Stabilizer Lock, 149 Tie Rod Ends, 131 to 132 Tine, Pickup Reel, 170, 173 Tire, Cultivator Gauge Wheel, 177 Tool, Clutch Alignment, 113 Tools, Sickle Repair, 168 Top Link End, 146 to 148 Top Link Pins, 150 Top Link, Three Point, 146 to 147 Transmission Bearing, 123 to 124 Bearing, PTO Shaft, 125 to 126 Bearings, 119 Bolt, Differential Ring Gear, 121 Coupler, Differential, 121 to 122 Cover, Clutch, 111 Cover, PTO, 125 Disc, Clutch, 112, 116, 119 Disc, Multi-Power, 119 Disc, PTO, 119 Disc, PTO Clutch, 112, 116 Gaskets, 119, 143, 153 Kits, Clutch, 111 Knob, Gear Shift, 118 Nut, Differential Ring Gear, 121 Pinion, Differential, 123 Plate, Friction, 121 Plate, PTO Clutch, 119 Pressure Plate, Clutch, 111 Resin Kit, Differential, 121 Ring Gear, Differential, 123 Shaft, PTO, 125 Shaft, PTO Conversion, 125 Shaft, PTO Pinion, 122 Spring, Multi-Power Piston Return, 119 Trim, Hood, 189 U Upholstery, Floormat, 193 V Valve, Expansion Massey Ferguson, 186 Valve Hydraulic, 162 Hydraulic Lift Cylinder Pressure Relief, 156 MF-

11 Valve (continued) Hydraulic Pressure Relief Valve, 156 Hydraulic Pump Control, 155 Hydraulic Pump Relief, 156 Isolator, 160 Pump Control, 155 Vise, Sickle Section Rivet, 168 Voltage Regulator, 104, 106 W Warning Light, 107 Washer Guard, Sickle, 168 Lock, Stabilizer Pin, 149 Spring, Pressure Plate, 113 Sweep, Cultivator, 177 Water Pump Repair Kit, 86 Water Pumps, 85 Water Temperature Gauge, 84 Water Temperature Sending Unit, 84 Weather Cap, Exhaust, 94 Webbing, Fuel Tank, 76 Wheel Bearings, Disc, 180 Bearings, Front, 136, 138 Bearings, Gauge Wheel, 177 Bolt, 139 to 140 Bolt, Front, 140 Cap, Hub, 138 Clamp, Rear, 140 Front, 139 Gauge, 177 Hub, 139 Nut, 140 Nut, Clamp Lock, 138 Nut, Front, 139 Rear, 140 Rim, Rear, 140 Screw, Power Adjust Stop, 140 Sleeve, Implement Wheel Seal, 180 Steering, 127 Stop, Power Adjust, 140 Tire, Cultivator Gauge Wheel, 177 Wires, Spark Plug, 97 Wood Block, Chain Idler, 175 MF-I

12 Model Machine Type Engine Index Fuel Engine model (CID) Page No. A Engine Diesel A Perkins MF-1-69 AT Engine Diesel AT Turbo Perkins MF-1-69 F40 Tractor Gas Z134 Continental MF-1-5 to MF-1-7 FE35 Tractor Diesel A3-152 Perkins.040 Sleeve flange thickness MF-1-17 to MF-1-19 FE35 Tractor Diesel A3-152 Perkins.150 Sleeve flange thickness MF-1-20 to MF-1-22 MF1080 Tractor Diesel A4-318 Perkins MF-1-57 to MF-1-58 MF1085 Tractor Diesel A4-318 Perkins MF-1-57 to MF-1-58 MF1100 Tractor Diesel A6-354 Perkins To Engine s/n 354UA3515 MF-1-59 to MF-1-60 MF1100 Tractor Diesel A6-354 Perkins Engine s/n 354UA3515 thru 354UA10361 MF-1-61 to MF-1-62 MF1100 Tractor Diesel A6-354 Perkins Engine s/n 354UA10362 & up MF-1-63 to MF-1-64 MF1105 Tractor Diesel AT6-354 Turbo Perkins MF-1-67 to MF-1-68 MF1130 Tractor Diesel AT6-354 Turbo Perkins To Engine s/n 354UA3356T MF-1-65 to MF-1-66 MF1135 Tractor Diesel AT6-354 Turbo Perkins MF-1-67 to MF-1-68 MF135 Tractor Diesel AD3-152 Perkins.150 Sleeve flange thickness MF-1-23 to MF-1-26 MF135 Tractor Gas AG3-152 Perkins MF-1-14 to MF-1-16 MF135 (Deluxe) MF135 (Special) Tractor Gas Z145 Continental MF-1-8 to MF-1-10 Tractor Gas Z134 Continental MF-1-5 to MF-1-7 MF150 Tractor Diesel AD3-152 Perkins.150 Sleeve flange thickness MF-1-23 to MF-1-26 MF150 Tractor Gas Z145 Continental MF-1-8 to MF-1-10 MF150 Tractor Gas AG3-152 Perkins MF-1-14 to MF-1-16 MF165 Tractor Diesel MF165 Tractor Diesel AD4-203 Perkins.150 Sleeve flange thickness Engine s/n to 29C1084 AD4-203 Perkins.150 Sleeve flange thickness Engine s/n 29C1084 & up MF-1-45 to MF-1-46 MF-1-47 to MF-1-48 MF165 Tractor Gas G176 Continental MF-1-11 to MF-1-12 MF175 Tractor Diesel A4-236 Perkins MF-1-49 to MF-1-50 MF180 Tractor Diesel A4-236 Perkins MF-1-49 to MF-1-50 MF230 Tractor Diesel AD3-152 Perkins.150 Sleeve flange thickness MF-1-27 to MF-1-29 MF235 Tractor Diesel MF235 Tractor Diesel MF235 Tractor Diesel MF235 Tractor Diesel AD3-152 Perkins.150 Sleeve flange thickness Engine s/n ending in DL AD3-152 Perkins.150 Sleeve flange thickness Engine s/n ending in DL AD3-152 Perkins.150 Sleeve flange thickness Engine s/n ending in DS AD3-152 Perkins.150 Sleeve flange thickness Engine s/n ending in DLS MF-1-23 to MF-1-26 MF-1-27 to MF-1-29 MF-1-30 to MF-1-32 MF-1-33 to MF-1-34 continues MF-II

13 Model Machine Type MF245 Tractor Diesel MF245 Tractor Diesel MF250 Tractor Diesel MF250 Tractor Diesel MF255 Tractor Diesel Engine Index Fuel Engine model (CID) Page No. AD3-152 Perkins.150 Sleeve flange thickness Engine s/n ending in DS AD3-152 Perkins.150 Sleeve flange thickness Engine s/n ending in DLS AD3-152 Perkins.150 Sleeve flange thickness Engine s/n prefix CE22488U only AD3-152 Perkins.150 Sleeve flange thickness Engine s/n prefix CE31089U only AD4-203 Perkins.150 Sleeve flange thickness Engine s/n 29C1084 & up MF-1-30 to MF-1-32 MF-1-33 to MF-1-34 MF-1-35 to MF-1-36 MF-1-37 to MF-1-38 MF-1-47 to MF-1-48 MF255 Tractor Diesel A4-236 Perkins MF-1-51 to MF-1-52 MF265 Tractor Diesel A4-236 Perkins To Engine s/n 236UA109215L MF-1-49 to MF-1-50 MF265 Tractor Diesel A4-236 Perkins Engine s/n 236UA109215L & up MF-1-51 to MF-1-52 MF275 Tractor Diesel A4-248 Perkins Engine s/n prefix 248UA or LF --- N or LF --- U only MF-1-53 to MF-1-54 MF285 Tractor Diesel A4-318 Perkins MF-1-57 to MF-1-58 MF290 Tractor Diesel A4-248 Perkins Early with 4 ring piston MF-1-55 to MF-1-56 MF294-4 Tractor Diesel A4-248 Perkins MF-1-55 to MF-1-56 MF35 Tractor Diesel A3-152 Perkins.040 Sleeve flange thickness MF-1-17 to MF-1-19 MF35 Tractor Diesel A3-152 Perkins.150 Sleeve flange thickness MF-1-20 to MF-1-22 MF35 Tractor Gas Z134 Continental MF-1-5 to MF-1-7 MF50 Tractor Diesel A3-152 Perkins.040 Sleeve flange thickness MF-1-17 to MF-1-19 MF50 Tractor Diesel A3-152 Perkins.150 Sleeve flange thickness MF-1-20 to MF-1-22 MF50 Tractor Gas Z134 Continental MF-1-5 to MF-1-7 MF65 Tractor Diesel MF65 Tractor Diesel MF65 Tractor Diesel MF65 Tractor Diesel MF65 Tractor Diesel A4-203 Perkins.040 Sleeve flange thickness To Engine s/n A4-203 Perkins.150 Sleeve flange thickness Engine s/n & up AD4-203 Perkins.040 Sleeve flange thickness To Engine s/n AD4-203 Perkins.150 Sleeve flange thickness Engine s/n to 29C1084 AD4-203 Perkins.150 Sleeve flange thickness Engine s/n 29C1084 & up MF-1-39 to MF-1-40 MF-1-41 to MF-1-42 MF-1-43 to MF-1-44 MF-1-45 to MF-1-46 MF-1-47 to MF-1-48 MF65 Tractor Gas G176 Continental MF-1-11 to MF-1-12 MF690 Tractor Diesel A4-248 Perkins To Engine s/n LF --- U839080J MF-1-55 to MF-1-56 MH44 Tractor Gas H260 MF-1-13 MH50 Tractor Gas Z134 Continental MF-1-5 to MF-1-7 Super 92 Combine Diesel A6-305 Perkins MF-1-70 TE20 Tractor Gas Z120 Continental MF-1-1 to MF-1-2 continues MF-III

14 Model Machine Type Engine Index Fuel Engine model (CID) Page No. TO20 Tractor Gas Z120 Continental MF-1-1 to MF-1-2 TO30 Tractor Gas Z129 Continental MF-1-3 to MF-1-4 TO35 Tractor Gas Z134 Continental MF-1-5 to MF Industrial Diesel 20 Industrial Diesel AD3-152 Perkins.150 Sleeve flange thickness To engine s/n 152UA391044DL AD3-152 Perkins.150 Sleeve flange thickness Engine s/n 152UA391044DL & up MF-1-23 to MF-1-26 MF-1-27 to MF Industrial Gas AG3-152 Perkins MF-1-14 to MF C Industrial Diesel 20C Industrial Diesel AD3-152 Perkins.150 Sleeve flange thickness Engine s/n ending in DS AD3-152 Perkins.150 Sleeve flange thickness Engine s/n ending in DLS MF-1-30 to MF-1-32 MF-1-33 to MF Crawler Diesel AD3-152 Perkins.150 Sleeve flange thickness MF-1-23 to MF B Crawler Diesel AD3-152 Perkins.150 Sleeve flange thickness MF-1-27 to MF Industrial Gas Z134 Continental MF-1-5 to MF Industrial Diesel 203 Industrial Diesel 203 Industrial Diesel A3-152 Perkins.040 Sleeve flange thickness To Tractor s/n A3-152 Perkins.150 Sleeve flange thickness To Tractor s/n AD3-152 Perkins.150 Sleeve flange thickness Tractor s/n & Up MF-1-17 to MF-1-19 MF-1-20 to MF-1-22 MF-1-23 to MF Industrial Gas Z134 Continental MF-1-5 to MF Industrial Diesel 205 Industrial Diesel 205 Industrial Diesel A3-152 Perkins.040 Sleeve flange thickness To Tractor s/n A3-152 Perkins.150 Sleeve flange thickness To Tractor s/n AD3-152 Perkins.150 Sleeve flange thickness Tractor s/n & Up MF-1-17 to MF-1-19 MF-1-20 to MF-1-22 MF-1-23 to MF Industrial Diesel AD3-152 Perkins.150 Sleeve flange thickness MF-1-23 to MF Treever Diesel AD3-152 Perkins.150 Sleeve flange thickness MF-1-23 to MF Forklift Diesel AD3-152 Perkins.150 Sleeve flange thickness MF-1-23 to MF Crawler Diesel AD3-152 Perkins.150 Sleeve flange thickness MF-1-23 to MF Forklift Diesel 2500 Forklift Diesel AD3-152 Perkins.150 Sleeve flange thickness To engine s/n 152UA391044DL AD3-152 Perkins.150 Sleeve flange thickness Engine s/n 152UA391044DL & up MF-1-23 to MF-1-26 MF-1-27 to MF Forklift Gas AG3-152 Perkins MF-1-14 to MF Industrial Diesel 30B Industrial Diesel AD4-203 Perkins.150 Sleeve flange thickness Engine s/n 29C1084 & up AD3-152 Perkins.150 Sleeve flange thickness Engine s/n ending in DS MF-1-47 to MF-1-48 MF-1-30 to MF-1-32 continues MF-IV

15 Model Machine Type 30B Industrial Diesel 300 Combine Diesel 300 Combine Diesel 302 Industrial Diesel 302 Industrial Diesel 304 Industrial Diesel 304 Industrial Diesel Engine Index Fuel Engine model (CID) Page No. AD3-152 Perkins.150 Sleeve flange thickness Engine s/n ending in DLS AD4-203 Perkins.150 Sleeve flange thickness Engine s/n to 29C1084 AD4-203 Perkins.150 Sleeve flange thickness Engine s/n 29C1084 & up AD4-203 Perkins.150 Sleeve flange thickness Engine s/n to 29C1084 AD4-203 Perkins.150 Sleeve flange thickness Engine s/n 29C1084 & up AD4-203 Perkins.150 Sleeve flange thickness Engine s/n to 29C1084 AD4-203 Perkins.150 Sleeve flange thickness Engine s/n 29C1084 & up MF-1-33 to MF-1-34 MF-1-45 to MF-1-46 MF-1-47 to MF-1-48 MF-1-45 to MF-1-46 MF-1-47 to MF-1-48 MF-1-45 to MF-1-46 MF-1-47 to MF Industrial Diesel A4-236 Perkins MF-1-49 to MF Industrial Diesel 3165 Industrial Diesel AD4-203 Perkins.150 Sleeve flange thickness Engine s/n to 29C1084 AD4-203 Perkins.150 Sleeve flange thickness Engine s/n 29C1084 & up MF-1-45 to MF-1-46 MF-1-47 to MF Utility Industrial Diesel A3-152 Perkins.040 Sleeve flange thickness MF-1-17 to MF Utility Industrial Diesel A3-152 Perkins.150 Sleeve flange thickness MF-1-20 to MF Tractor Shovel Tractor Shovel Tractor Shovel Tractor Shovel Tractor Shovel Diesel Diesel Diesel Diesel Diesel 40 Industrial Diesel 40 Industrial Diesel A4-203 Perkins.040 Sleeve flange thickness To Engine s/n A4-203 Perkins.150 Sleeve flange thickness Engine s/n & up AD4-203 Perkins.040 Sleeve flange thickness To Engine s/n AD4-203 Perkins.150 Sleeve flange thickness Engine s/n to 29C1084 AD4-203 Perkins.150 Sleeve flange thickness Engine s/n 29C1084 & up AD3-152 Perkins.150 Sleeve flange thickness To engine s/n 152UA391044DL AD3-152 Perkins.150 Sleeve flange thickness Engine s/n 152UA391044DL & up MF-1-39 to MF-1-40 MF-1-41 to MF-1-42 MF-1-43 to MF-1-44 MF-1-45 to MF-1-46 MF-1-47 to MF-1-48 MF-1-23 to MF-1-26 MF-1-27 to MF Industrial Gas AG3-152 Perkins MF-1-14 to MF B Industrial Diesel AD4-203 Perkins.150 Sleeve flange thickness Engine s/n 29C1084 & up MF-1-47 to MF Forklift Diesel AD3-152 Perkins.150 Sleeve flange thickness MF-1-27 to MF Industrial Diesel AD4-203 Perkins.150 Sleeve flange thickness Engine s/n 29C1084 & up MF-1-47 to MF C Industrial Diesel A4-236 Perkins MF-1-51 to MF-1-52 continues MF-V

16 Model Machine Type Engine Index Fuel Engine model (CID) Page No. 540 Combine Diesel A4-318 Perkins MF-1-57 to MF Forklift Diesel A4-236 Perkins To Engine s/n 236UA109215L MF-1-49 to MF Forklift Diesel A4-236 Perkins Engine s/n 236UA109215L & up MF-1-51 to MF Combine Diesel AT6-354 Turbo Perkins To Machine s/n MF-1-67 to MF Combine Diesel AT6-354 Turbo Perkins To Machine s/n MF-1-67 to MF-1-68 MF-VI

17 YEAR OF MANUFACTURE AND STARTING SERIAL NUMBER MF MF MF MF MF MF-90WR MF-97D MF-97LPG MF A A A A A A A A A MF A A A A A A A A A MF S A C C S A C C01511 MF A A A A A A A A A S A C C S A C C02679 MF A A A A A A A A A MF A A A A A A A A A MF F D D D F D D D S D S D00393 MF A MF MF MF MF MF MF A A A A A A A A MF P Q R S A B C01001 MF A A MF-VII

18 MF V N R S A B C01001 MF A A A A A A A A MF MF N P R S A B C01001 MF M MF A A A A A A A MF A B C01001 MF A A A A A A A A A MF MF N MF A A A A A A A A A MF-282(S) KC24457S KD26466S MF-282(H) KC25226H KD25518H MF R B C01001 MF A A A A A A A A A MF MF D MF MF U V N P R A01001 MF R S A B C01001 MF P R S A B01001 MF P R S A B01001 MF-375, MF U V N P R S A B C01001 MF P R S A B C01001 MF U V N P R S A B C01001 MF-390T, MF P R S A B01001 MF-393, MF A B C01001 MF-398, MF U V N P R S A B C01001 MF B K T L U MF B K L U MF B K T L U MF T L U MF-VIII

19 1010 2WD NA WD HYDRO NA WD WD HYDRO NA WD WD HYDRO NA WD WD HYDRO NA MF WD MF WD MF-1030L MF WD MF-1030L MF WD NA MF WD MF WD MF WD MF WD NA MF WD MF B B B B31958 MF B B B B B B76058 MF B B B B B B31958 MF B B B B B B B76058 MF A40101 MF B B B B B B31958 MF-1135, MF B B B B B B B76058 MF S A50101 MF S A50101 MF S A50101 MF WD A B70101 MF A B80101 MF A A90101 MF B10101 MF B20101 MF B30101 MF A B40101 MF A B50101 MF A B60101 MF-1500, MF C C C C MF-1505, MF C C C C MF-I

20 2640 2WD S B K WD S B K MF-2675, MF R R R R R R03525 MF R R R R R R MF R R R R R R R MF R R R R R R R R MF U V N P MF U V N P R MF U V N P R S A B MF B C MF U V N P R MF-3120, MF R S A B C MF K L U V MF K L U V MF K L U V MF-3630, MF V N P R MF R S A B C MF A B C MF N P R S MF S A B C MF D D D D D MF-4840, MF D D D D D D MF D D D D MF-

21 MF-I

22 1 ENGINES Replacement parts to fit Tractor: TE20, TO20 Z CID 4 Cylinder Continental Gas 3-5/16" Overbore Supplied, Standard Bore 3-3/16" TRU-POWER Engine Kits (Pin type valves furnished in EOK.) Engine bearings must be ordered separately. Cylinder Parts 20K600-LCB BEKM118-LCB Complete overhaul kit. Contains sleeve & piston kit, complete gasket set, pin bushings, valve overhaul kit, fan belt, oil pump repair kit, oil filter element, air cleaner hose, upper & lower radiator hose, distributor points & condenser, spark plugs, Marvel-Schebler basic carburetor kit. Basic engine kit. Contains sleeves, sleeve seals, pistons & rings, pins & retainers, pin bushings, gasket sets, & crankshaft seals. PRS M M91 Ring set for 4 pistons. For 3-5/16" overbore Super Power pistons. 3/32", 5/32" Ring set for 4 pistons. For 3-3/16" standard bore replacing original rings. 1/8", 3/16" Bushing kit, M1 pin bushings. EOK118-LCB Engine overhaul kit. Contains sleeves, pistons, rings, pins, overhaul gasket set, valves, springs, guides, and keys M1 Bushing, piston pin BIFM118 Basic in-frame kit. Contains sleeve & piston kit with rings, pins & retainers, valve grind set, oil pan gasket. Gaskets Sleeve & Piston Kit M91 Complete gasket set, less crankshaft seals. TO20VG Valve grinding set M1 Gasket, cylinder head M1 Gasket, timing gear cover M1 Gasket, hand hole cover to pan. Complete for one engine. (Super Power Kit increases bore to 3-5/16".) M M1 Gasket, cylinder head cover. Gasket, vent cover, cylinder head. PK106 Sleeve & piston kit. Contains sleeves, sleeve seals, pistons & rings, pins & retainers. Increases bore to 3-5/16" M M1 Seal, oil, intake valve stem Gasket, manifold. Tractors: TO20, TO30, TO35, MF35, F40, MF50, MF M1 Gasket, oil pan to block M1 Gasket, rubber, cylinder sleeve M1 Packing, rear main bearing cap. MF-1-1

23 1 ENGINES Tractor: TE20, TO20 Z CID 4 Cylinder Continental Gas 3-5/16" Overbore Supplied, Standard Bore 3-3/16" Crankshaft Seals Connecting Rod Bearing Kits 1 kit used per engine A Seal, front, lip-type A Front dust seal, felt. For Continental engines M91 Rod bearing kit, standard M92 Seal, rear, lip-type. For Continental engines M91 Rod bearing kit,.002" M1 Rear seal gasket. Use with M M91 Rod bearing kit,.010" CSK3 Seal kit. Contains front seal & dust felt, rear seal & gasket for crankshaft. For Continental engines. Valve Parts M Rod bearing kit,.020" Rod bearing kit,.030" Main Bearing Kits Includes thrust washers (1 kit used per engine) Pin Type Valves MBKZ120 Main bearing kit, standard VOKM120 Valve overhaul kit. Contains intake & exhaust valves, springs, keys, guides. MBKZ MBKZ Main bearing kit,.010" Main bearing kit,.020" M1 Valve, engine intake, pin type M1 Valve, engine exhaust, pin type M91 Valve, engine exhaust, pin type (set of 4) M91 Guide, intake & exhaust valve (set of 8) 21176A Spring, intake & exhaust valve M91 Spring, intake & exhaust valve (set of 8) 18291A Lock, intake & exhaust valve, pin type (1 used per valve) M1 Seal, oil, intake valve stem MF-1-2

24 1 ENGINES Replacement parts to fit Tractor: TO30 Z CID 4 Cylinder Continental Gas 3-3/8" Overbore Supplied, Standard Bore 3-1/4" TRU-POWER Engine Kits (Pin-type intake & key-type exhaust valves furnished in EOK) "Super Power" sleeve & piston kit, increases bore to 3-3/8". Engine bearings must be ordered separately. Cylinder Parts 30K600-LCB Complete overhaul kit. Contains sleeve & piston kit, complete gasket set, pin bushings, valve overhaul kit, fan belt, oil pump repair kit, oil filter element, air cleaner hose, upper & lower radiator hose, distributor points & condenser, spark plugs, Marvel-Schebler basic carburetor kit. PRS M M1 Ring set for 4 pistons. For 3-3/8" overbore Super Power pistons. 3/32", 3/16" Ring set for 4 pistons. For 3-1/4" standard bore replacing original rings. 1/8", 3/16" Bushing, piston pin EOK119FL-LCB Engine overhaul kit. Contains sleeves, pistons & rings, pins & retainers, pin bushings, complete gasket set, crankshaft seals, valves, springs, guides, & keys M91 Bushing kit, M1 pin bushings. BEKM119FL-LCB Basic engine kit. Contains sleeves, sleeve seals, pistons & rings, pins & retainers, pin bushings, gasket sets, crankshaft seals. Gaskets BIFM119FL Basic in-frame kit. Contains sleeve & piston kit with rings, pins & retainers, valve grind gasket set, oil pan gasket. Sleeve & Piston Kit M91 Complete gasket set, less crankshaft seals. TO20VG Valve grinding set M1 Gasket, cylinder head M1 Gasket, timing gear cover M1 Gasket, cylinder head cover M1 Gasket, vent cover, cylinder head. PK105 Complete for one engine. (Super Power Kit, increases bore to 3-3/8") Sleeve & piston Kit. Contains sleeves, sleeve seals, pistons & rings, pins & retainers. Increases bore to 3-3/8" M M M M1 Seal, oil, intake valve stem Gasket, manifold. Tractors: TO20, TO30, TO35, MF35, F40, MF50, MF135. Gasket, oil pan to block. Gasket, rubber, cylinder sleeve M1 Packing, rear main bearing cap. MF-1-3

25 1 ENGINES Tractor: TO30 Z CID 4 Cylinder Continental Gas 3-3/8" Overbore Supplied, Standard Bore 3-1/4" Crankshaft Seals Connecting Rod Bearing Kits 1 kit used per engine A Seal, front, lip-type A Front dust seal, felt. For Continental engines M91 Rod bearing kit, standard M92 Seal, rear, lip-type. For Continental engines M91 Rod bearing kit,.002" M1 Rear seal gasket. Use with M M91 Rod bearing kit,.010" CSK3 Seal kit. Contains front seal & dust felt, rear seal & gasket for crankshaft. For Continental engines. Valve Parts (Pin-type intake, key-type exhaust) M Rod bearing kit,.020" Rod bearing kit,.030" Main Bearing Kits Includes thrust washers (1 kit used per engine) VOKM129 Valve overhaul kit. Contains intake & exhaust valves, springs, keys, guides M M M M M91 Valve, engine intake, pin type Valve, engine intake, pin type (set of 4) Valve, engine exhaust, key type Valve, engine exhaust, key type (set of 4) Guide, intake & exhaust valve (set of 8) MBKZ120 MBKZ MBKZ Main bearing kit, standard Main bearing kit,.010" Main bearing kit,.020" Crankshaft Kits 21176A Spring, intake & exhaust valve M A Spring, intake & exhaust valve (set of 8) Lock, intake & exhaust valve, pin type (1 used per valve) Z129CK Crankshaft kit with standard size rod & main bearings. For Z129 Continental gas engine in tractors: TO30 with thrust on front main M1 Lock, intake & exhaust valve, key type (2 used per valve). Replaces M91 Lock, intake & exhaust valve, key type (set of 8) M1 Seal, oil, intake valve stem MF-1-4

26 1 ENGINES Replacement parts to fit Industrial Tractor: 202, 204 Tractor: F40, MF135, MF35, MF50, TO35 Z CID 4 Cylinder Continental Gas 3-3/8"" Overbore Supplied, Standard Bore 3-5/16"" TRU-POWER Engine Kits (Pin-type intake & key-type exhaust valves furnished in EOK) "Super Power" sleeve & piston kit, increases bore to 3-3/8". Engine bearings must be ordered separately. Sleeve & Piston Kit 35K600-LCB 45K600-LCB Complete overhaul kit for TO35, MF35, MF135, 202 & 204 industrials. Contains sleeve & piston kit, complete gasket set, pin bushings, valve overhaul kit, fan belt, oil pump repair kit, oil filter element, air cleaner hose, upper & lower radiator hose, distributor points & condenser, spark plugs, Marvel-Schebler basic carburetor kit. Complete overhaul kit for F40 & MF50. Contains sleeve & piston kit, complete gasket set, pin bushings, valve overhaul kit, fan belt, oil pump repair kit, oil filter element, air cleaner hose, upper & lower radiator hose, distributor points & condenser, spark plugs, Marvel-Schebler basic carburetor kit. PK105 Complete for one engine. (Super Power Kit, increases bore to 3-3/8") Sleeve & piston Kit. Contains sleeves, sleeve seals, pistons & rings, pins & retainers. Increases bore to 3-3/8". Cylinder Parts EOK119-LCB BEKM119-LCB BIFM119 Engine overhaul kit. Contains sleeves, sleeve seals, pistons & rings, pins & retainers, pin bushings, complete gasket set, crankshaft seals, valves, springs, guides, & keys. Basic engine kit. Contains sleeves, sleeve seals, pistons & rings, pins & retainers, pin bushings, gasket sets, crankshaft seals. Basic in-frame kit. Contains sleeve & piston kit with rings, pins & retainers, valve grind gasket set, oil pan gasket. PRS M M M91 Ring set for 4 pistons. For 3-3/8" overbore Super Power pistons. 3/32", 3/16" Ring set for 4 pistons. For 3-5/16" standard bore replacing original rings. 1/8", 3/16". Bushing, piston pin Bushing kit, M1 pin bushings. MF-1-5

27 1 ENGINES Industrial Tractor: 202, 204 Tractor: F40, MF135, MF35, MF50, TO35 Z CID 4 Cylinder Continental Gas 3-3/8"" Overbore Supplied, Standard Bore 3-5/16"" Gaskets Valve Parts M91 Complete gasket set, with front seals M91 Valve grinding set M1 Gasket, cylinder head M M M M M M M M M1 Gasket, timing gear cover. For tractors: TO35, MF50, MF35. Gasket, cylinder head cover. Gasket, vent cover, cylinder head. Seal, oil, intake valve stem Gasket, manifold. Tractors: TO20, TO30, TO35, MF35, F40, MF50, MF135. Gasket, oil pan to block. Gasket, oil pan. For tractors: MF35. Gasket, rubber, cylinder sleeve. Packing, rear main bearing cap. Crankshaft Seals VOKM M M M M M A M A (Pin-type intake, key-type exhaust) Valve overhaul kit. Contains intake & exhaust valves, springs, keys, guides. Valve, engine intake, pin type Valve, engine intake, pin type (set of 4) Valve, engine exhaust, key type Valve, engine exhaust, key type (set of 4) Guide, intake & exhaust valve (set of 8) Spring, intake & exhaust valve Spring, intake & exhaust valve (set of 8) Lock, intake & exhaust valve, pin type (1 used per valve) M1 Lock, intake & exhaust valve, key type (2 used per valve). Replaces M91 Lock, intake & exhaust valve, key type (set of 8) M1 Seal, oil, intake valve stem 15287A Seal, front, lip-type A Front dust seal, felt. For Continental engines M92 Seal, rear, lip-type. For Continental engines M1 Rear seal gasket. Use with M92. CSK3 Seal kit. Contains front seal & dust felt, rear seal & gasket for crankshaft. For Continental engines. MF-1-6

28 1 ENGINES Replacement parts to fit Industrial Tractor: 202, 204 Tractor: F40, MF135, MF35, MF50, TO35 Z CID 4 Cylinder Continental Gas 3-3/8"" Overbore Supplied, Standard Bore 3-5/16"" Connecting Rod Bearing Kits 1 kit used per engine. Crankshaft Kits M M91 Rod bearing kit, standard Rod bearing kit,.002" Z134CK Crankshaft kit with standard size rod & main bearings. For Z134 Continental gas engine in tractors: TO30 late with thrust on center main, TO35, MF35, MF135; industrial: 202. Camshafts M91 Rod bearing kit,.010" M91 Rod bearing kit,.020" Rod bearing kit,.030" Main Bearing Kits (Flanged center main bearing) 1 kit used per engine M91 Camshaft, for Continental gas engines Z120, Z129, Z134. Replaces M1, M1. Oil Pump Repair Kits M M M Main bearing kit, standard Main bearing kit,.010" Main bearing kit,.020" Main bearing kit,.030" OPK60A M1 Complete repair kit; replaces M91, Drive gear is 2-15/16" O.D. Gasket, oil pump body cover. For tractors: TO35, F40, MF35, & MF50. MF-1-7

29 1 ENGINES Tractor: MF135 (Deluxe), MF150 Z CID 4 Cylinder Continental Gas Standard Bore 3-3/8" TRU-POWER Engine Kits Standard Bore 3-3/8". (Pin type intake & key type exhaust valves furnished in EOK) Bearings must be ordered separately. Cylinder Parts 37K600-LCB Complete overhaul kit. Contains sleeve & piston kit, complete gasket set, pin bushings, valve overhaul kit, fan belt, oil pump repair kit, oil filter element, air cleaner hose, upper & lower radiator hose, distributor points & condenser, spark plugs, Marvel-Schebler basic carburetor kit M M M91 Ring set for 4 pistons. For 3-3/8" standard bore. 1/8", 3/16" Bushing, piston pin Bushing kit, M1 pin bushings. BEKM1135-LCB EOK1135-LCB Basic engine kit. Contains sleeves, sleeve seals, piston & rings, pins & retainers, pin bushings, gasket sets, crankshaft seals. Engine overhaul kit. Contains sleeves, pistons & rings, pins & retainers, pin bushings, complete gasket set, crankshaft seals, valves, springs, guides, & keys. Gaskets BIFM1135 Basic in-frame kit. Contains sleeve & piston kit with rings, pins & retainers, valve grinding set, oil pan gasket. Sleeve & Piston Kit M M91 Complete gasket set, with front seals. Valve grinding set M1 Gasket, cylinder head M1 Gasket, cylinder head cover M1 Gasket, vent cover, cylinder head M1 Seal, oil, intake valve stem M1 Gasket, manifold. Tractors: TO20, TO30, TO35, MF35, F40, MF50, MF135. PK135 Sleeve & piston kit. Contains sleeves, sleeve seals, pistons & rings, pins & retainers. For standard 3-3/8" bore M M M1 Gasket, timing gear cover. For tractors: TO35, MF50, MF35. Gasket, oil pan to block. Gasket, rubber, cylinder sleeve M1 Packing, rear main bearing cap. MF-1-8

30 1 ENGINES Replacement parts to fit Tractor: MF135 (Deluxe), MF150 Z CID 4 Cylinder Continental Gas Standard Bore 3-3/8" Crankshaft Seals Connecting Rod Bearing Kits 1 kit used per engine A Seal, front, lip-type A Front dust seal, felt. For Continental engines M91 Rod bearing kit, standard M92 Seal, rear, lip-type. For Continental engines M91 Rod bearing kit,.002" M1 Rear seal gasket. Use with M M91 Rod bearing kit,.010" CSK3 Seal kit. Contains front seal & dust felt, rear seal & gasket for crankshaft. For Continental engines. Valve Parts M Rod bearing kit,.020" Rod bearing kit,.030" Main Bearing Kits (Flanged center main bearing) 1 kit used per engine. VOKM M M M A M91 (Pin-type intake, key-type exhaust) Valve overhaul kit. Contains intake & exhaust valves, springs, keys, & guides. Valve, engine intake, pin type (4 used per engine) Valve, engine exhaust, key type (4 used per engine) Guide, intake & exhaust valve (set of 8) Spring, intake & exhaust valve Spring, intake & exhaust valve (set of 8) M M M M1 Main bearing kit, standard Main bearing kit,.010" Main bearing kit,.020" Main bearing kit,.030" Timing Gears Crankshaft gear, 24 teeth. For Continental gas engine in tractors: TO35, MF35, MF50, MH50, MF135, MF A M M M1 Lock, intake & exhaust valve, pin type (1 used per valve) Lock, intake & exhaust valve, key type (2 used per valve). Replaces Lock, intake & exhaust valve, key type (set of 8) Seal, oil, intake valve stem M1 Camshaft gear, 48 teeth. For Continental gas engine in tractors: TE20, TO20, TO30, TO35, F40, MH50, MF50, MF135, MF150; industrials: 202, 204, MF-1-9

31 1 ENGINES Tractor: MF135 (Deluxe), MF150 Z CID 4 Cylinder Continental Gas Standard Bore 3-3/8" Camshafts M1 Camshaft with nut, 10 tooth, 1.234" gear. For Continental Z145 gas engine in tractors: MF135, MF150, MF230, MF235, MF245; industrials: 20C, 30B; forklifts: 2500, MF-1-10

32 1 ENGINES Replacement parts to fit Tractor: MF165, MF65 G CID 4 Cylinder Continental Gas Standard Bore 3-37/64" Stepped Head Piston TRU-POWER Engine Kits Standard Bore 3-37/64". Bearings must be ordered separately. Cylinder Parts 65K600-LCB BEKM165-LCB EOK165-LCB Complete overhaul kit. Contains sleeve & piston kit, complete gasket set, pin bushings, valve overhaul kit, fan belt, oil pump repair kit, oil filter element, air cleaner hose, upper & lower radiator hose, distributor points & condenser, spark plugs, Marvel-Schebler basic carburetor kit. Basic engine kit. Contains sleeves, sleeve seals, pistons & rings, pins & retainers, pin bushings, gasket set, crankshaft seals. Engine overhaul kit. Contains sleeves, pistons & rings, pins & retainers, pin bushings, complete gasket set, crankshaft seals, valves, springs, guides, & keys M M M91 Ring set, for 4 pistons. For 3-37/64" standard bore. 1/8", 1/4" Piston pin bushing. Bushing kit, M1 pin bushings. Gaskets BIFM165 Basic in-frame kit. Contains sleeve & piston kit with rings, pins & retainers, valve grinding gasket set, oil pan gasket. Sleeve & Piston Kit M M91 Complete gasket set, with front & rear crankshaft seals. Valve grinding set M1 Gasket, cylinder head M1 Seal, oil, intake valve stem M1 Gasket, rubber, cylinder sleeve M1 Gasket, oil pan M1 Packing, rear main bearing cap. Complete for one engine (Standard bore 3-37/64") Stepped head piston M92 Crankshaft Seals Seal, rear, lip-type. For Continental engines. PK65 Sleeve & piston kit. Contains sleeves, sleeve seals, pistons & rings, pins & retainers. For standard 3-37/64" bore. MF-1-11

33 1 ENGINES Tractor: MF165, MF65 G CID 4 Cylinder Continental Gas Standard Bore 3-37/64" Stepped Head Piston Valve Parts Main Bearing Kits 1 kit used per engine M91 Main bearing kit, standard M91 Main bearing kit,.010" M91 Main bearing kit,.020" VOKM176 Valve overhaul kit. Contains intake & exhaust valves, springs, keys, & guides. Oil Pump Repair Kits M1 Valve, engine intake M91 Valve, engine intake (set of 4) M1 Valve, engine exhaust M91 Valve, engine exhaust (set of 4) M M M1 Guide, intake & exhaust valve Guide, intake & exhaust valve (set of 8) Spring, intake & exhaust valve OPK65A Oil pump repair kit. For Continental engine in tractors: MF65, MF165, MF175, MF180. Drive gear is 3-1/8" O.D M91 Spring, intake & exhaust valve (set of 8) M91 Key, intake & exhaust valve (set of 16) Connecting Rod Bearing Kits 1 kit used per engine M91 Rod bearing kit, standard M91 Rod bearing kit,.010" M91 Rod bearing kit,.020" MF-1-12

34 1 ENGINES Replacement parts to fit Tractor: MH44 ( ) H CID 4 Cylinder Continental Gas 4" Overbore Supplied, Standard Bore 3-7/8" Flat Head Piston TRU-POWER Engine Kits Super Power sleeve & piston kit, increases bore to 4". Engine bearings must be order separately. Gaskets BEKM1325-LCB Basic engine kit. Contains sleeves, pistons, rings, pins, and overhaul gasket set with crankshaft seal. Sleeve and Piston Kit M2 Oil pan gasket set.tractors: MH44 ( ) H260 4 cylinder Continental Gas. Complete for one engine. VGK7624B Valve grinding set. Flat head piston Valve Parts PK325 Sleeve & piston kit. Contains sleeves, sleeve seals, pistons & rings, pins & retainers. 4" bore. Cylinder Parts M91 Guide, intake & exhaust valves (set of 8) M1 Piston pin bushing M91 Key, intake & exhaust valve (set of 16) Connecting Rod Bearing Kits 1 kit used per engine M91 Bushing kit, M1 pin bushings M92 Rod bearing kit, standard MF-1-13

35 1 ENGINES Forklift: 2500 Industrial Tractor: 20, 40 Tractor: MF135, MF150 AG CID 3 Cylinder Perkins Gas Standard Bore 3.6" TRU-POWER Engine Kits Gaskets BEKP152G-LCB Basic engine kit. Contains sleeves, pistons, rings, pins, pin bushings, and overhaul gasket set with crankshaft seals. EOK152G-LCB Engine overhaul kit. Contains sleeves, pistons, rings, pins, pin bushings, overhaul gasket set with crankshaft seals, valves, springs, guides, and keys. BIFP152G Basic in-frame kit. Contains sleeves, pistons, rings, pins, valve grind set, and oil pan gasket kit. Sleeve & Piston Kit M M91 Top engine set. Bottom engine set. MF3152PG Oil pan gasket. Crankshaft Seals M1 Seal, front, lip-type. PK152G Sleeve & piston kit. Contains sleeves, pistons & rings, pins & retainers. Complete for 3-cylinders M1 Seal, rear, rope-type. For original production blocks (2 required) M1 Cylinder Parts Sleeve, CAST, replacing original CAST sleeve. Flange thickness.150". Replaces M M91 Seal, rear, lip-type (s/n 248UA123424L & up). For replacement blocks (2 required) M M1 Ring set, for 1 piston. 3/32", 1/4". Bushing, piston pin (3 used per engine) *Both rear seal types included in engine kits MF-1-14

36 1 ENGINES Replacement parts to fit Forklift: 2500 Industrial Tractor: 20, 40 Tractor: MF135, MF150 AG CID 3 Cylinder Perkins Gas Standard Bore 3.6" Valve Parts Main Bearing Kits 1 kit used per engine (Thrust washers not included) M91 Main bearing kit, standard VOKP152G M M M M M1 Valve overhaul kit. Contains intake & exhaust valves, springs, keys, guides. Valve, engine intake Valve, engine exhaust Guide, intake & exhaust valve Spring, inner, intake & exhaust valve Spring, outer, intake & exhaust valve M M M M1 Main bearing kit,.010" Main bearing kit,.020" Main bearing kit,.030" Thrust Washers Thrust washer, upper. 2 used per engine M1 Key, intake & exhaust valve (12 used per engine) Connecting Rod Bearing Kits 1 kit used per engine M1 Thrust washer, lower, tabbed. 2 used per engine M91 Rod bearing kit, standard M91 Rod bearing kit,.010" M91 Rod bearing kit,.020" M91 Rod bearing kit,.030" MF-1-15

37 1 ENGINES Forklift: 2500 Industrial Tractor: 20, 40 Tractor: MF135, MF150 AG CID 3 Cylinder Perkins Gas Standard Bore 3.6" Crankshaft Kits M M M91 Crankshaft kit, new, with standard rod bearings, main bearings, & thrust washers. For Perkins AG3-152 gas, A3-152 & AD3-152 diesels. Uses 2 piece rope-type rear seal. 1/2" wide flywheel flange. Crankshaft kit, new, with standard size rod & main bearings, & thrust washers. For Perkins AG3-152 gas & AD3-152 diesel engines using 1 piece lip-type rear seal, keyed nose, 1-1/2" wide flywheel flange. Replaces U5BG0027, M91, M91, M91. Oil Pump Repair Kits Oil pump assembly for Perkins A3-152 & AD3-152 gas & diesel engines. Replaces & M91. MF-1-16

38 1 ENGINES Replacement parts to fit Industrial Tractor: 203 (prior to tractor s/n ), 205 (prior to tractor s/n ), 35 Utility Tractor: FE35, MF35, MF50 A CID 3 Cylinder Perkins Diesel Standard Bore 3.6".040 Sleeve Flange Thickness Injectors Vertical in Head BEKP1335D-LCB TRU-POWER Engine Kits Used prior to engine s/n , replacing original chrome sleeves (.040" sleeve flange thickness) Engine bearings & thrust washers must be ordered separately. Basic engine kit. Contains sleeves (.040" flange thickness), pistons, rings, pins, pin bushings, and overhaul gasket set with crankshaft seals M-CST M91 Cylinder Parts Sleeve, CAST, for replacing original CHROME sleeve. Flange thickness.040". Piston with pin, flat head. EOK1335D-LCB BIFP1335D Engine overhaul kit. Contains sleeves (.040" sleeve flange thickness), pistons, rings, pins, pin bushings, overhaul gasket set with crankshaft seals, valves, springs, guides, retainers, and keys. Basic in-frame kit. Contains sleeves (.040" flange thickness), pistons, rings, pins, valve grind set, and oil pan gasket kit. Sleeve & Piston Kit PRS334DC M91 Ring set for 3 pistons only, use with CHROME sleeves, can replace M92. 3/32", 1/8", 1/4". Ring set, for 1 piston, used with CAST sleeves only. 3/32", 1/8", and 1/4" M1 Bushing, piston pin (3 used per engine) PK334DC Complete for 1 engine Kit, with original style M1 CHROME sleeves, flange thickness.040" M1 Crankshaft Seals Seal, front, lip-type. PK335D Kit, with CAST sleeves, for REPLACING original style CHROME sleeves. Flange thickness.040" M1 Seal, rear, rope-type. For original production blocks (2 required) MF-1-17

39 1 ENGINES Industrial Tractor: 203 (prior to tractor s/n ), 205 (prior to tractor s/n ), 35 Utility Tractor: FE35, MF35, MF50 A CID 3 Cylinder Perkins Diesel Standard Bore 3.6".040 Sleeve Flange Thickness Injectors Vertical in Head Gaskets Valve Parts M M91 MF3152PG Lower engine gaskets are for engines using 2 piece rope-type rear seal. Seals are included in engine kits but are not included in gasket sets. Top engine set. Bottom set, to engine s/n 19B8552. Oil pan gasket. Connecting Rod Bearing Kits VOKP M M M M M1 Valve overhaul kit. Contains intake & exhaust valves, springs, keys, & guides. Valve, intake Valve, exhaust Guide, intake & exhaust valve Spring, inner, intake & exhaust valve Spring, outer, intake & exhaust valve M1 Retainer, valve spring M1 Key, intake & exhaust valve (12 used per engine) Main Bearing Kits 1 kit used per engine M91 Rod bearing kit, standard M M M91 Rod bearing kit,.010" Rod bearing kit,.020" Rod bearing kit,.030" M M91 1 kit used per engine (Thrust washers not included) Main bearing kit, standard Main bearing kit,.010" M91 Main bearing kit,.020" M91 Main bearing kit,.030" MF-1-18

40 1 ENGINES Replacement parts to fit Industrial Tractor: 203 (prior to tractor s/n ), 205 (prior to tractor s/n ), 35 Utility Tractor: FE35, MF35, MF50 A CID 3 Cylinder Perkins Diesel Standard Bore 3.6".040 Sleeve Flange Thickness Injectors Vertical in Head Thrust Washers Crankshaft Kits M1 Thrust washer, upper. 2 used per engine M1 Thrust washer, lower, tabbed. 2 used per engine M91 Crankshaft kit, new, with standard rod bearings, main bearings, & thrust washers. For Perkins AG3-152 gas, A3-152 & AD3-152 diesels. Uses 2 piece rope-type rear seal. 1/2" wide flywheel flange. Cylinder Heads M91 Crankshaft kit, new, with standard size rod & main bearings, & thrust washers. For Perkins AG3-152 gas & AD3-152 diesel engines using 1 piece lip-type rear seal, keyed nose, 1-1/2" wide flywheel flange. Replaces U5BG0027, M91, M91, M91. Oil Pump Repair Kits M91 Oil pump assembly for Perkins A3-152 & AD3-152 gas & diesel engines. Replaces & M M91 Cylinder head assembly, for Perkins A3-152 regular injection engine (injectors vertical in cylinder head). Head assembly includes valves & valve parts. Tractors: MF35, MF50; industrials: 35 utility, 203, 205. Replaces ZZ080058, M91. MF-1-19

41 1 ENGINES Industrial Tractor: 203 (prior to tractor s/n ), 205 (prior to tractor s/n ), 35 Utility Tractor: FE35, MF35, MF50 A CID 3 Cylinder Perkins Diesel Standard Bore 3.6".150 Sleeve Flange thickness Injectors Vertical in Head BEKP1336D-LCB TRU-POWER Engine Kits Used engine s/n & up (.150" sleeve flange thickness). Engine bearings & thrust washers must be ordered separately. Basic engine kit. Contains sleeves (.150" sleeve flange thickness), pistons, rings, pins, pin bushings, and complete gasket set with crankshaft seals M M M91 Cylinder Parts Sleeve, CAST, replacing original CAST sleeve. Flange thickness.150". Replaces M1. Piston with pin, flat head. Ring set, for 1 piston, used with CAST sleeves only. 3/32", 1/8", and 1/4" EOK1336D-LCB Engine overhaul kit. Contains sleeves (.150" sleeve flange thickness), pistons, rings, pins, pin bushings, overhaul gasket set with crankshaft seals, valves, springs, guides, retainers, and keys. BIFP1336D Basic in-frame kit. Contains sleeves (.150" sleeve flange thickness), pistons, rings, pins, valve grind set, and oil pan gasket kit. Sleeve & Piston Kit M1 Bushing, piston pin (3 used per engine) Gaskets PK336D Complete for 1 engine Flat head piston Sleeve & piston kit. Contains CAST sleeves, flange thickness.150", pistons & rings, pins & retainers. Complete for 3-cylinders M M92 MF3152PG Lower engine gaskets are for engines using 2 piece rope-type rear seal. Seals are included in engine kits but are not included in gasket sets. Top engine set. Bottom engine set (s/n 19B8552 & up) *seal not included Oil pan gasket. MF-1-20

42 1 ENGINES Replacement parts to fit Industrial Tractor: 203 (prior to tractor s/n ), 205 (prior to tractor s/n ), 35 Utility Tractor: FE35, MF35, MF50 A CID 3 Cylinder Perkins Diesel Standard Bore 3.6".150 Sleeve Flange thickness Injectors Vertical in Head Crankshaft Seals Connecting Rod Bearing Kits M1 Seal, front, lip-type M1 Seal, rear, rope-type. For original production blocks (2 required) Valve Parts M91 1 kit used per engine. Rod bearing kit, standard M91 Rod bearing kit,.010" M91 Rod bearing kit,.020" M91 Rod bearing kit,.030" Main Bearing Kits VOKP152 Valve overhaul kit. Contains intake & exhaust valves, springs, keys, & guides M1 Valve, intake M1 Valve, exhaust M M M M M1 Guide, intake & exhaust valve Spring, inner, intake & exhaust valve Spring, outer, intake & exhaust valve Retainer, valve spring Key, intake & exhaust valve (12 used per engine) M M M M91 1 kit used per engine (Thrust washers not included) Main bearing kit, standard Main bearing kit,.010" Main bearing kit,.020" Main bearing kit,.030" MF-1-21

43 1 ENGINES Industrial Tractor: 203 (prior to tractor s/n ), 205 (prior to tractor s/n ), 35 Utility Tractor: FE35, MF35, MF50 A CID 3 Cylinder Perkins Diesel Standard Bore 3.6".150 Sleeve Flange thickness Injectors Vertical in Head Thrust Washers Crankshaft Kits M1 Thrust washer, upper. 2 used per engine M1 Thrust washer, lower, tabbed. 2 used per engine M91 Crankshaft kit, new, with standard rod bearings, main bearings, & thrust washers. For Perkins AG3-152 gas, A3-152 & AD3-152 diesels. Uses 2 piece rope-type rear seal. 1/2" wide flywheel flange. Cylinder Heads M91 Crankshaft kit, new, with standard size rod & main bearings, & thrust washers. For Perkins AG3-152 gas & AD3-152 diesel engines using 1 piece lip-type rear seal, keyed nose, 1-1/2" wide flywheel flange. Replaces U5BG0027, M91, M91, M91. Oil Pump Repair Kits M91 Oil pump assembly for Perkins A3-152 & AD3-152 gas & diesel engines. Replaces & M M91 Cylinder head assembly, for Perkins A3-152 regular injection engine (injectors vertical in cylinder head). Head assembly includes valves & valve parts. Tractors: MF35, MF50; industrials: 35 utility, 203, 205. Replaces ZZ080058, M91. MF-1-22

44 1 ENGINES Replacement parts to fit Crawler: 200, 2244 Forklift: 2200, 2500 (prior to s/n 152UA391044DL) Industrial Tractor: 20, 40 (prior to s/n 152UA391044DL), 2135, 203 (tractor s/n & up), 205 (tractor s/n & up) Tractor: MF135, MF150, MF235 (with engine s/n ending in "D") Treever: 2200 AD CID 3 Cylinder Perkins Diesel Standard Bore 3.6".150 Flange Thickness Injectors at Angle in Cylinder Head 2 Piece rope-type rear seal TRU-POWER Engine Kits For engines with 2-piece rope-type rear crankshaft seal. Not for engines with serial number ending in L or S. Engines with L s/n ending use lip-type rear seal. Engines with S s/n ending use different pistons, rings, & valves with 35º face angle. Engine bearings & thrust washers must be ordered separately. Sleeve & Piston Kit BEKP1337D-LCB EOK1337D-LCB BIFP1337D Basic engine kit. Contains sleeves, pistons, rings, pins, pin bushings, and overhaul gasket set with crankshaft seals. Engine overhaul kit. Contains sleeves, pistons, rings, pins, pin bushings, overhaul gasket set with crankshaft seals, valves, springs, guides, retainers, and keys. Basic in-frame kit. Contains sleeves, pistons, rings, pins, valve grind set, and oil pan gasket kit. PK337D Complete for one engine..150" flange thickness 5 ring piston Sleeve & piston kit. Contains sleeves, pistons & rings, pins & retainers. Complete for 3-cylinders. Cylinder Parts M1 Sleeve, CAST, replacing original CAST sleeve. Flange thickness.150". Replaces M M91 Piston (w/pin), cupped head M91 Ring set, for 1 piston, used with CAST sleeves only. 3/32", 1/8", and 1/4" M1 Bushing, piston pin (3 used per engine) MF-1-23

45 1 ENGINES Crawler: 200, 2244 Forklift: 2200, 2500 (prior to s/n 152UA391044DL) Industrial Tractor: 20, 40 (prior to s/n 152UA391044DL), 2135, 203 (tractor s/n & up), 205 (tractor s/n & up) Tractor: MF135, MF150, MF235 (with engine s/n ending in "D") Treever: 2200 AD CID 3 Cylinder Perkins Diesel Standard Bore 3.6".150 Flange Thickness Injectors at Angle in Cylinder Head 2 Piece rope-type rear seal Gaskets Valve Parts Lower engine gaskets are for engines using 2 piece rope-type rear seal. Seals are included in engine kits but are not included in gasket sets M M M92 MF3152PG Head gasket only. Top engine set. Bottom engine set (s/n 19B8552 & up) *seal not included Oil pan gasket. Crankshaft Seals VOKP152A M M M M1 Valve overhaul kit. Contains intake & exhaust valves, springs, keys, & guides. Valve, intake (3 used per engine) Valve, exhaust Guide, intake & exhaust valve Spring, inner, intake & exhaust valve M1 Seal, front, lip-type M1 Spring, outer, intake & exhaust valve M1 Retainer, valve spring M1 Key, intake & exhaust valve (12 used per engine) M1 Seal, rear, rope-type. For original production blocks (2 required) MF-1-24

46 1 ENGINES Replacement parts to fit Crawler: 200, 2244 Forklift: 2200, 2500 (prior to s/n 152UA391044DL) Industrial Tractor: 20, 40 (prior to s/n 152UA391044DL), 2135, 203 (tractor s/n & up), 205 (tractor s/n & up) Tractor: MF135, MF150, MF235 (with engine s/n ending in "D") Treever: 2200 AD CID 3 Cylinder Perkins Diesel Standard Bore 3.6".150 Flange Thickness Injectors at Angle in Cylinder Head 2 Piece rope-type rear seal Connecting Rod Bearing Kits Thrust Washers M1 Thrust washer, upper. 2 used per engine. 1 kit used per engine M1 Thrust washer, lower, tabbed. 2 used per engine M91 Rod bearing kit, standard M M91 Rod bearing kit,.010" Rod bearing kit,.020" Crankshaft Kits M91 Rod bearing kit,.030" Main Bearing Kits M91 Crankshaft kit, new, with standard rod bearings, main bearings, & thrust washers. For Perkins AG3-152 gas, A3-152 & AD3-152 diesels. Uses 2 piece rope-type rear seal. 1/2" wide flywheel flange M M M91 1 kit used per engine (Thrust washers not included) Main bearing kit, standard Main bearing kit,.010" Main bearing kit,.020" M91 Crankshaft kit, new, with standard size rod & main bearings, & thrust washers. For Perkins AG3-152 gas & AD3-152 diesel engines using 1 piece lip-type rear seal, keyed nose, 1-1/2" wide flywheel flange. Replaces U5BG0027, M91, M91, M M91 Main bearing kit,.030" MF-1-25

47 1 ENGINES Crawler: 200, 2244 Forklift: 2200, 2500 (prior to s/n 152UA391044DL) Industrial Tractor: 20, 40 (prior to s/n 152UA391044DL), 2135, 203 (tractor s/n & up), 205 (tractor s/n & up) Tractor: MF135, MF150, MF235 (with engine s/n ending in "D") Treever: 2200 AD CID 3 Cylinder Perkins Diesel Standard Bore 3.6".150 Flange Thickness Injectors at Angle in Cylinder Head 2 Piece rope-type rear seal Cylinder Heads M M91 Cylinder head assembly, for Perkins AD3-152 direct injection engines (injectors at angle in cylinder head). Includes valves & valve parts. For tractors: MF135, MF150, MF230, MF235, MF245; industrials: 20, 20C 30B, 30D, 40, 203, 205, 2135, 2200 treever; forklifts: 2200, 2500, 4500; crawlers: 200, 200B, 200C, Replaces cylinder heads M91, M91, M91, these heads have valves with a 45 degree face angle & are no longer supplied by OEM M91 is the same as supplied by the OEM & has valves with a 35 degree face angle. Replaces ZZ080082, ZZ080025, M91. Oil Pump Repair Kits Oil pump assembly for Perkins A3-152 & AD3-152 gas & diesel engines. Replaces & M91. MF-1-26

48 1 ENGINES Replacement parts to fit Crawler: 200B Forklift: 2500 (s/n 152UA391044DL & up), 4500 Industrial Tractor: 20, 40 (with engine s/n 152UA391044DL & up) Tractor: MF230, MF235 (with engine s/n ending in "DL") AD CID 3 Cylinder Perkins Diesel Standard Bore 3.6".150 Flange Thickness Injectors at Angle in Cylinder Head With lip type rear seal BEKP2337-LCB TRU-POWER Engine Kits For engines with 1 piece lip type rear seal. For engines with s/n ending in DL. Not for engines with S in s/n ending. Engines with S s/n ending use different pistons, rings, & have valves with a 35º face angle. Engine bearings & thrust washers must be ordered separately. Basic engine kit. Contains sleeves, pistons, rings, pins, pin bushings, and overhaul gasket set with crankshaft seals M M M M1 Cylinder Parts Sleeve, CAST, replacing original CAST sleeve. Flange thickness.150". Replaces M1. Piston (w/pin), cupped head Ring set, for 1 piston, used with CAST sleeves only. 3/32", 1/8", and 1/4" Bushing, piston pin (3 used per engine) EOK2337-LCB BIFP1337D Engine overhaul kit. Contains sleeves, pistons, rings, pins, pin bushings, overhaul gasket set with crankshaft seals, valves, springs, guides, retainers, and keys. Basic in-frame kit. Contains sleeves, pistons, rings, pins, valve grind set, and oil pan gasket kit. Gaskets Sleeve & Piston Kit Lower engine gaskets are for engines using 1 piece lip type rear crankshaft seal. Crankshaft seals are included in engine kits but are not included in gasket sets. PK337D Complete for one engine..150" flange thickness 5 ring piston Sleeve & piston kit. Contains sleeves, pistons & rings, pins & retainers. Complete for 3-cylinders M M M91 MF3152PG Head gasket only. Top engine set. Bottom engine set, for engines with serial number ending in DLS with lip type rear seal. *seal not included Oil pan gasket. MF-1-27

49 1 ENGINES Crawler: 200B Forklift: 2500 (s/n 152UA391044DL & up), 4500 Industrial Tractor: 20, 40 (with engine s/n 152UA391044DL & up) Tractor: MF230, MF235 (with engine s/n ending in "DL") AD CID 3 Cylinder Perkins Diesel Standard Bore 3.6".150 Flange Thickness Injectors at Angle in Cylinder Head With lip type rear seal Crankshaft Seals Connecting Rod Bearing Kits M1 Seal, front, lip-type M91 Seal, rear, lip-type (s/n 248UA123424L & up). For replacement blocks (2 required) Valve Parts M91 1 kit used per engine. Rod bearing kit, standard M91 Rod bearing kit,.010" M91 Rod bearing kit,.020" M91 Rod bearing kit,.030" Main Bearing Kits VOKP152A Valve overhaul kit. Contains intake & exhaust valves, springs, keys, & guides M1 Valve, intake (3 used per engine) M1 Valve, exhaust M M M M M1 Guide, intake & exhaust valve Spring, inner, intake & exhaust valve Spring, outer, intake & exhaust valve Retainer, valve spring Key, intake & exhaust valve (12 used per engine) M M M M91 1 kit used per engine (Thrust washers not included) Main bearing kit, standard Main bearing kit,.010" Main bearing kit,.020" Main bearing kit,.030" MF-1-28

50 1 ENGINES Replacement parts to fit Crawler: 200B Forklift: 2500 (s/n 152UA391044DL & up), 4500 Industrial Tractor: 20, 40 (with engine s/n 152UA391044DL & up) Tractor: MF230, MF235 (with engine s/n ending in "DL") AD CID 3 Cylinder Perkins Diesel Standard Bore 3.6".150 Flange Thickness Injectors at Angle in Cylinder Head With lip type rear seal Thrust Washers Crankshaft Kits M1 Thrust washer, upper. 2 used per engine M1 Thrust washer, lower, tabbed. 2 used per engine M91 Crankshaft kit, new, with standard rod bearings, main bearings, & thrust washers. For Perkins AG3-152 gas, A3-152 & AD3-152 diesels. Uses 2 piece rope-type rear seal. 1/2" wide flywheel flange. Cylinder Heads M91 Crankshaft kit, new, with standard size rod & main bearings, & thrust washers. For Perkins AG3-152 gas & AD3-152 diesel engines using 1 piece lip-type rear seal, keyed nose, 1-1/2" wide flywheel flange. Replaces U5BG0027, M91, M91, M91. Oil Pump Repair Kits M91 Cylinder head assembly, for Perkins AD3-152 direct injection engines (injectors at angle in cylinder head). Includes valves & valve parts. For tractors: MF135, MF150, MF230, MF235, MF245; industrials: 20, 20C 30B, 30D, 40, 203, 205, 2135, 2200 treever; forklifts: 2200, 2500, 4500; crawlers: 200, 200B, 200C, Replaces cylinder heads M91, M91, M91, these heads have valves with a 45 degree face angle & are no longer supplied by OEM M91 is the same as supplied by the OEM & has valves with a 35 degree face angle. Replaces ZZ080082, ZZ080025, M M91 Oil pump assembly for Perkins A3-152 & AD3-152 gas & diesel engines. Replaces & M91. MF-1-29

51 1 ENGINES Industrial Tractor: 20C, 30B Tractor: MF235, MF245 AD3-152 Direct Injection 152 CID 3 Cylinder Perkins Diesel Standard Bore 3.6".150 Flange Thickness Injectors at Angle in Cylinder Head 35 degree face angle valves 2 Piece rope-type rear seal For engine s/n ending in S. These engines are different from AD3-152 without S or LS ending. Pistons & rings differ in compression ring; intake & exhaust valves differ in face angle BEKP152DS-LCB EOK152DS-LCB BIFP152DS TRU-POWER Engine Kits For engines with serial number ending in DS. Bottom gasket set in this kit is for engine with 2 piece rope type rear seal. Engine bearings & thrust washers must be ordered separately. Basic engine kit. Contains sleeves, pistons, rings, pins, pin bushings, and overhaul gasket set with crankshaft seals. Engine overhaul kit. Contains sleeves, pistons, rings, pins, pin bushings, overhaul gasket set with crankshaft seals, valves, springs, guides, retainers, and keys. Basic in-frame kit. Contains sleeves, pistons, rings, pins, valve grind set, and oil pan gasket kit. Sleeve & Piston Kit M M M1 Cylinder Parts Sleeve, CAST, replacing original CAST sleeve. Flange thickness.150". Replaces M1. Ring set, for 1 piston, use with CAST sleeves only. 3/32", 3/16" Bushing, piston pin (3 used per engine) Gaskets Lower engine gaskets are for engines using 2 piece rope-type rear seal. Seals are included in engine kits but are not included in gasket sets M2 Head gasket only M91 Top engine set M92 Bottom engine set (s/n 19B8552 & up) *seal not included Complete for 1 engine.150" flange thickness 4 ring piston MF3152PG M1 Oil pan gasket. Crankshaft Seals Seal, front, lip-type. PK152S Sleeve & piston kit. Contains sleeves, pistons, rings, pins & retainers. Complete for 3-cylinders M1 Seal, rear, rope-type. For original production blocks (2 required) MF-1-30

52 1 ENGINES Replacement parts to fit Industrial Tractor: 20C, 30B Tractor: MF235, MF245 AD3-152 Direct Injection 152 CID 3 Cylinder Perkins Diesel Standard Bore 3.6".150 Flange Thickness Injectors at Angle in Cylinder Head 35 degree face angle valves 2 Piece rope-type rear seal For engine s/n ending in S. These engines are different from AD3-152 without S or LS ending. Pistons & rings differ in compression ring; intake & exhaust valves differ in face angle Valve Parts Main Bearing Kits VOKP152B M M M M M1 Valve overhaul kit. Contains intake & exhaust valves, springs, keys, & guides. Valve, intake, 35º face angle Valve, exhaust, 35 face angle Guide, intake & exhaust valve Spring, outer, intake & exhaust valve Key, intake & exhaust valve (12 used per engine) Connecting Rod Bearing Kits M M M M M1 1 kit used per engine (Thrust washers not included) Main bearing kit, standard Main bearing kit,.010" Main bearing kit,.020" Main bearing kit,.030" Thrust Washers Thrust washer, upper. 2 used per engine M1 Thrust washer, lower, tabbed. 2 used per engine. 1 kit used per engine M91 Rod bearing kit, standard M91 Rod bearing kit,.010" M91 Rod bearing kit,.020" M91 Rod bearing kit,.030" MF-1-31

53 1 ENGINES Industrial Tractor: 20C, 30B Tractor: MF235, MF245 AD3-152 Direct Injection 152 CID 3 Cylinder Perkins Diesel Standard Bore 3.6".150 Flange Thickness Injectors at Angle in Cylinder Head 35 degree face angle valves 2 Piece rope-type rear seal For engine s/n ending in S. These engines are different from AD3-152 without S or LS ending. Pistons & rings differ in compression ring; intake & exhaust valves differ in face angle Cylinder Heads Oil Pump Repair Kits M91 Oil pump assembly for Perkins A3-152 & AD3-152 gas & diesel engines. Replaces & M M91 Cylinder head assembly, for Perkins AD3-152 direct injection engines (injectors at angle in cylinder head). Includes valves & valve parts. For tractors: MF135, MF150, MF230, MF235, MF245; industrials: 20, 20C 30B, 30D, 40, 203, 205, 2135, 2200 treever; forklifts: 2200, 2500, 4500; crawlers: 200, 200B, 200C, Replaces cylinder heads M91, M91, M91, these heads have valves with a 45 degree face angle & are no longer supplied by OEM M91 is the same as supplied by the OEM & has valves with a 35 degree face angle. Replaces ZZ080082, ZZ080025, M91. Crankshaft Kits M91 Crankshaft kit, new, with standard rod bearings, main bearings, & thrust washers. For Perkins AG3-152 gas, A3-152 & AD3-152 diesels. Uses 2 piece rope-type rear seal. 1/2" wide flywheel flange M91 Crankshaft kit, new, with standard size rod & main bearings, & thrust washers. For Perkins AG3-152 gas & AD3-152 diesel engines using 1 piece lip-type rear seal, keyed nose, 1-1/2" wide flywheel flange. Replaces U5BG0027, M91, M91, M91. MF-1-32

54 1 ENGINES Replacement parts to fit Industrial Tractor: 20C, 30B Tractor: MF235, MF245 AD3-152 Direct Injection 152 CID 3 Cylinder Perkins Diesel Standard Bore 3.6".150 Flange Thickness Injectors at Angle in Cylinder Head 35 degree face angle valves With lip type rear seal BEKP152DLS-LCB EOK152DLS-LCB BIFP152DS TRU-POWER Engine Kits For engines with serial number ending in DLS. Bottom gasket set in this kit is for engine with lip-type rear seal. Engine bearings & thrust washers must be ordered separately. Basic engine kit. Contains sleeves, pistons, rings, pins, pin bushings, and overhaul gasket set with crankshaft seals. Engine overhaul kit. Contains sleeves, pistons, rings, pins, pin bushings, overhaul gasket set with crankshaft seals, valves, springs, guides, retainers, and keys. Basic in-frame kit. Contains sleeves, pistons, rings, pins, valve grind set, and oil pan gasket kit. Sleeve & Piston Kit M M M1 Cylinder Parts Sleeve, CAST, replacing original CAST sleeve. Flange thickness.150". Replaces M1. Ring set, for 1 piston, use with CAST sleeves only. 3/32", 3/16" Bushing, piston pin (3 used per engine) Gaskets Lower engine gaskets are for engines using 1 piece lip type rear crankshaft seal. Crankshaft seals are included in engine kits but are not included in gasket sets M2 Head gasket only M91 Top engine set. Complete for 1 engine.150" flange thickness 4 ring piston M91 MF3152PG Bottom engine set, for engines with serial number ending in DLS with lip type rear seal. *seal not included Oil pan gasket. Crankshaft Seals PK152S Sleeve & piston kit. Contains sleeves, pistons, rings, pins & retainers. Complete for 3-cylinders M1 Seal, front, lip-type M91 Seal, rear, lip-type (s/n 248UA123424L & up). For replacement blocks (2 required) MF-1-33

55 1 ENGINES Industrial Tractor: 20C, 30B Tractor: MF235, MF245 AD3-152 Direct Injection 152 CID 3 Cylinder Perkins Diesel Standard Bore 3.6".150 Flange Thickness Injectors at Angle in Cylinder Head 35 degree face angle valves With lip type rear seal Valve Parts Connecting Rod Bearing Kits VOKP152B M M M M M1 Valve overhaul kit. Contains intake & exhaust valves, springs, keys, & guides. Valve, intake, 35º face angle Valve, exhaust, 35 face angle Guide, intake & exhaust valve Spring, outer, intake & exhaust valve Key, intake & exhaust valve (12 used per engine) Thrust Washers M M M M91 1 kit used per engine. Rod bearing kit, standard Rod bearing kit,.010" Rod bearing kit,.020" Rod bearing kit,.030" Main Bearing Kits M1 Thrust washer, upper. 2 used per engine M1 Thrust washer, lower, tabbed. 2 used per engine. 1 kit used per engine (Thrust washers not included) M91 Main bearing kit, standard M91 Main bearing kit,.010" M91 Main bearing kit,.020" M91 Main bearing kit,.030" MF-1-34

56 1 ENGINES Replacement parts to fit Tractor: MF CID 3 Cylinder Perkins Diesel Standard Bore 3.6" Engine Serial Number: Engine S/N prefix CE22488U Only Perkins piston.150 Flange Thickness Injectors at Angle in Cylinder Head BEKP2337-LCB TRU-POWER Engine Kits Basic engine kit. Contains sleeves, pistons, rings, pins, pin bushings, and overhaul gasket set with crankshaft seals. Gasket Sets & Crankshaft Seals BIFP1337D Basic in-frame kit. Contains sleeves, pistons, rings, pins, valve grind set, and oil pan gasket kit. Sleeve and Piston Kit M2 Head gasket only M91 Top engine set M91 Bottom engine set, for engines with serial number ending in DLS with lip type rear seal. *seal not included PK337D Complete for 1 engine (Engine uses Perkins piston #68332)..150" flange thickness 5 ring piston Sleeve & piston kit. Contains sleeves, pistons & rings, pins & retainers. Complete for 3-cylinders. MF3152PG M M91 Oil pan gasket. Seal, front, lip-type. Seal, rear, lip-type (s/n 248UA123424L & up). For replacement blocks (2 required) Connecting Rod Bearing Kits Cylinder Parts M1 Sleeve, CAST, replacing original CAST sleeve. Flange thickness.150". Replaces M M91 Piston (w/pin), cupped head M91 Ring set, for 1 piston, used with CAST sleeves only. 3/32", 1/8", and 1/4" 1 kit used per engine M91 Rod bearing kit, standard M91 Rod bearing kit,.010" M91 Rod bearing kit,.020" M1 Bushing, piston pin (3 used per engine) M91 Rod bearing kit,.030" MF-1-35

57 1 ENGINES Tractor: MF CID 3 Cylinder Perkins Diesel Standard Bore 3.6" Engine Serial Number: Engine S/N prefix CE22488U Only Perkins piston.150 Flange Thickness Injectors at Angle in Cylinder Head Main Bearing Kits Crankshaft Kits M M M M M1 1 kit used per engine (Thrust washers not included) Main bearing kit, standard Main bearing kit,.010" Main bearing kit,.020" Main bearing kit,.030" Thrust Washers Thrust washer, upper. 2 used per engine M M M91 Crankshaft kit, new, with standard rod bearings, main bearings, & thrust washers. For Perkins AG3-152 gas, A3-152 & AD3-152 diesels. Uses 2 piece rope-type rear seal. 1/2" wide flywheel flange. Crankshaft kit, new, with standard size rod & main bearings, & thrust washers. For Perkins AG3-152 gas & AD3-152 diesel engines using 1 piece lip-type rear seal, keyed nose, 1-1/2" wide flywheel flange. Replaces U5BG0027, M91, M91, M91. Oil Pump Repair Kits Oil pump assembly for Perkins A3-152 & AD3-152 gas & diesel engines. Replaces & M M1 Thrust washer, lower, tabbed. 2 used per engine. MF-1-36

58 1 ENGINES Replacement parts to fit Tractor: MF CID 3 Cylinder Perkins Diesel Standard Bore 3.6" Engine Serial Number: Engine S/N prefix CE31089U Only Perkins piston.150 Flange Thickness Injectors at Angle in Cylinder Head BEKP152DLS-LCB TRU-POWER Engine Kits Basic engine kit. Contains sleeves, pistons, rings, pins, pin bushings, and overhaul gasket set with crankshaft seals. Gasket Sets & Crankshaft Seals BIFP152DS Basic in-frame kit. Contains sleeves, pistons, rings, pins, valve grind set, and oil pan gasket kit. Sleeve & Piston Kit M M91 Head gasket only. Top engine set M91 Bottom engine set, for engines with serial number ending in DLS with lip type rear seal. *seal not included MF3152PG Oil pan gasket M1 Seal, front, lip-type. Complete for 1 engine (engine uses Perkins piston).150" flange thickness 4 ring piston M91 Seal, rear, lip-type (s/n 248UA123424L & up). For replacement blocks (2 required) Connecting Rod Bearing Kits PK152S Sleeve & piston kit. Contains sleeves, pistons, rings, pins & retainers. Complete for 3-cylinders. Cylinder Parts M1 Sleeve, CAST, replacing original CAST sleeve. Flange thickness.150". Replaces M1. 1 kit used per engine M91 Ring set, for 1 piston, use with CAST sleeves only. 3/32", 3/16" M M91 Rod bearing kit, standard Rod bearing kit,.010" M1 Bushing, piston pin (3 used per engine) M M91 Rod bearing kit,.020" Rod bearing kit,.030" MF-1-37

59 1 ENGINES Tractor: MF CID 3 Cylinder Perkins Diesel Standard Bore 3.6" Engine Serial Number: Engine S/N prefix CE31089U Only Perkins piston.150 Flange Thickness Injectors at Angle in Cylinder Head Main Bearing Kits Crankshaft Kits M M M M M1 1 kit used per engine (Thrust washers not included) Main bearing kit, standard Main bearing kit,.010" Main bearing kit,.020" Main bearing kit,.030" Thrust Washers Thrust washer, upper. 2 used per engine M M M91 Crankshaft kit, new, with standard rod bearings, main bearings, & thrust washers. For Perkins AG3-152 gas, A3-152 & AD3-152 diesels. Uses 2 piece rope-type rear seal. 1/2" wide flywheel flange. Crankshaft kit, new, with standard size rod & main bearings, & thrust washers. For Perkins AG3-152 gas & AD3-152 diesel engines using 1 piece lip-type rear seal, keyed nose, 1-1/2" wide flywheel flange. Replaces U5BG0027, M91, M91, M91. Oil Pump Repair Kits Oil pump assembly for Perkins A3-152 & AD3-152 gas & diesel engines. Replaces & M M1 Thrust washer, lower, tabbed. 2 used per engine. MF-1-38

60 1 ENGINES Replacement parts to fit Industrial Tractor: 356 Tractor Shovel Tractor: MF65 A4-203 Regular Injection 203 CID 4 Cylinder Perkins Diesel Standard Bore 3.6".040 Sleeve Flange Thickness Injectors Vertical in Head BEKP1465D-LCB EOK1465D-LCB BIFP1465D TRU-POWER Engine Kits Used prior to engine s/n (.040" sleeve flange thickness). Engine bearings and thrust washers must be ordered separately. Basic engine kit. Contains sleeves, pistons, rings, pins, pin bushings, and overhaul gasket set with crankshaft seals. Engine overhaul kit. Contains sleeves, pistons, rings, pins, pin bushings, overhaul gasket set with crankshaft seals, valves, springs, guides, retainers, and keys. Basic in-frame kit. Contains sleeve and piston kit with rings, pins, and retainers, top engine gasket set, and oil pan gasket M-CST M91 PRS462DC M M1 Cylinder Parts Sleeve, CAST, for replacing original CHROME sleeve. Flange thickness.040". Piston with pin, flat head. Ring set, use with CHROME sleeves only. 3/32", 1/8", 1/4" Ring set, for 1 piston, used with CAST sleeves only. 3/32", 1/8", and 1/4" Bushing, piston pin (4 used per engine) Sleeve & Piston Kit Gaskets Crankshaft seals are included in engine kits but are not included in gasket sets M91 Top engine set. PK462DC Complete for 1 engine Flat head piston Sleeve and piston kit, with original style M1 CHROME sleeves, flange thickness.040". Contains piston, sleeves, pins, locks and rings. Sleeves not available separately M91 MF4203PG M1 Bottom engine set. Oil pan gasket. Crankshaft Seals Seal, front, lip-type. PK465D Sleeve and piston kit, with CAST sleeves, for replacing original style chrome sleeves. Flange.040". Contains piston, sleeves, pins, locks and rings M1 Seal, rear, rope-type. For original production blocks (2 required) MF-1-39

61 1 ENGINES Industrial Tractor: 356 Tractor Shovel Tractor: MF65 A4-203 Regular Injection 203 CID 4 Cylinder Perkins Diesel Standard Bore 3.6".040 Sleeve Flange Thickness Injectors Vertical in Head Valve Parts Connecting Rod Bearing Kits 1 kit used per engine M91 Rod bearing kit, standard VOKP M M M1 Valve overhaul kit. Contains intake and exhaust valves, springs, keys, and guides. Valve, intake Valve, exhaust Guide, intake & exhaust valve M M M91 Rod bearing kit,.010" Rod bearing kit,.020" Rod bearing kit,.030" Main Bearing Kits M1 Spring, inner, intake & exhaust valve M1 Spring, outer, intake & exhaust valve M1 Retainer, valve spring M M1 Key, intake & exhaust valves, pair (16 used per engine) Thrust Washers Thrust washer, upper. 2 used per engine M M M91 1 kit used per engine (Thrust washers not included) Main bearing kit, standard Main bearing kit,.010" Main bearing kit,.020" M91 Main bearing kit,.030" M1 Thrust washer, lower, tabbed. 2 used per engine. Crankshaft Kits M91 Crankshaft kit for A4-203 & AD4-203 Perkins Diesels using 2 piece rope-type rear seal. Shaft not splined on gear end. MF-1-40

62 1 ENGINES Replacement parts to fit Industrial Tractor: 356 Tractor Shovel Tractor: MF65 A4-203 Regular Injection 203 CID 4 Cylinder Perkins Diesel Standard Bore 3.6".150 Sleeve Flange Thickness Injectors Vertical in Head BEKP1466D-LCB EOK1466D-LCB TRU-POWER Engine Kits Used engine s/n & up (.150" sleeve flange thickness). Engine bearings and thrust washers must be ordered separately. Basic engine kit. Contains sleeves, pistons, rings, pins, pin bushings, and overhaul gasket set with crankshaft seals. Engine overhaul kit. Contains sleeves, pistons, rings, pins, pin bushings, overhaul gasket set with crankshaft seals, valves, springs, guides, retainers, and keys M M M M1 Cylinder Parts Sleeve, CAST, replacing original CAST sleeve. Flange thickness.150". Replaces M1. Piston with pin, flat head. Ring set, for 1 piston, used with CAST sleeves only. 3/32", 1/8", and 1/4" Bushing, piston pin (4 used per engine) BIFP1466D Basic in-frame kit. Contains sleeve and piston kit with rings, pins and retainers, top engine gasket set, and oil pan gasket. Gaskets Sleeve & Piston Kit Crankshaft seals are included in engine kits but are not included in gasket sets. PK466D Flat head piston Sleeve and piston kit. Contains CAST sleeves, flange thickness,.150", pistons and rings, pin and retainers M M91 MF4203PG Top engine set. Bottom engine set. Oil pan gasket. Crankshaft Seals M1 Seal, front, lip-type M1 Seal, rear, rope-type. For original production blocks (2 required) MF-1-41

63 1 ENGINES Industrial Tractor: 356 Tractor Shovel Tractor: MF65 A4-203 Regular Injection 203 CID 4 Cylinder Perkins Diesel Standard Bore 3.6".150 Sleeve Flange Thickness Injectors Vertical in Head Valve Parts Oil Pump Repair Kits M91 Oil pump assembly for Perkins A4-203 & AD4-203 gas & diesel engines. Replaces , M91. Main Bearing Kits VOKP203 Valve overhaul kit. Contains intake and exhaust valves, springs, keys, and guides M M M M M M M1 Valve, intake Valve, exhaust Guide, intake & exhaust valve Spring, inner, intake & exhaust valve Spring, outer, intake & exhaust valve Retainer, valve spring Key, intake & exhaust valves, pair (16 used per engine) Connecting Rod Bearing Kits M M M M M1 1 kit used per engine (Thrust washers not included) Main bearing kit, standard Main bearing kit,.010" Main bearing kit,.020" Main bearing kit,.030" Thrust Washers Thrust washer, upper. 2 used per engine M1 Thrust washer, lower, tabbed. 2 used per engine. 1 kit used per engine M M91 Rod bearing kit, standard Rod bearing kit,.010" Crankshaft Kits M91 Rod bearing kit,.020" M91 Rod bearing kit,.030" M91 Crankshaft kit for A4-203 & AD4-203 Perkins Diesels using 2 piece rope-type rear seal. Shaft not splined on gear end. MF-1-42

64 1 ENGINES Replacement parts to fit Industrial Tractor: 356 Tractor Shovel Tractor: MF65 AD4-203 Direct Injection 203 CID 4 Cylinder Perkins Diesel Standard Bore 3.6".040 Sleeve Flange Thickness Injectors at Angle in Cylinder Head 2 Piece rope-type rear seal BEKP1464D-LCB EOK1464D-LCB BIFP1464D TRU-POWER Engine Kits Used prior to engine s/n (.040" sleeve flange thickness). Engine bearings and thrust washers must be ordered separately. Basic engine kit. Contains sleeves, pistons, rings, pins, pin bushings, and overhaul gasket set with crankshaft seals. Engine overhaul kit. Contains sleeves, pistons, rings, pins, pin bushings, overhaul gasket set with crankshaft seals, valves, springs, guides, and keys. Basic in-frame kit. Contains sleeve and piston kit with rings, pins, and retainers, top engine gasket set, and oil pan gasket M-CST M91 PRS462DC M M1 Cylinder Parts Sleeve, CAST, for replacing original CHROME sleeve. Flange thickness.040". Piston (w/pin), cupped head Ring set, use with CHROME sleeves only. 3/32", 1/8", 1/4" Ring set, for 1 piston, used with CAST sleeves only. 3/32", 1/8", and 1/4" Bushing, piston pin (4 used per engine) PK463DC Sleeve and Piston Kit Complete for one engine. Used prior to engine s/n For engines originally produced with CHROME sleeves. Sleeve and piston kit. Contains original style M1 CHROME sleeves, flange thickness.040", piston and rings, pin and retainers. Sleeves not available separately M M92 MFD4203PG Gaskets For engines using 2 piece rope-type rear seal, NOT for engines with DL in serial number ending. Crankshaft seals are included in engine kits but are not included in gasket sets. Top engine set. Bottom set, to engine s/n 29C1084. Oil pan gasket. Crankshaft Seals PK464D Sleeve and piston kit. Contains CAST sleeves, for replacing original style chrome sleeves, flange thickness,.040", piston and rings, pin and retainers M1 Seal, front, lip-type M1 Seal, rear, rope-type. For original production blocks (2 required) MF-1-43

65 1 ENGINES Industrial Tractor: 356 Tractor Shovel Tractor: MF65 AD4-203 Direct Injection 203 CID 4 Cylinder Perkins Diesel Standard Bore 3.6".040 Sleeve Flange Thickness Injectors at Angle in Cylinder Head 2 Piece rope-type rear seal Valve Parts Connecting Rod Bearing Kits 1 kit used per engine. VOKP203A M M M M M M M1 Valve overhaul kit. Contains intake and exhaust valves, springs, keys, and guides. Valve, intake (4 used per engine) Valve, exhaust Guide, intake & exhaust valve Spring, inner, intake & exhaust valve Spring, outer, intake & exhaust valve Retainer, valve spring Key, intake & exhaust valves, pair (16 used per engine) Thrust Washers M1 Thrust washer, lower, tabbed. 2 used per engine M1 Thrust washer, upper. 2 used per engine M M M M M M M M91 Rod bearing kit, standard Rod bearing kit,.010" Rod bearing kit,.020" Rod bearing kit,.030" Main Bearing Kits 1 kit used per engine (Thrust washers not included) Main bearing kit, standard Main bearing kit,.010" Main bearing kit,.020" Main bearing kit,.030" Crankshaft Kits M91 Crankshaft kit for A4-203 & AD4-203 Perkins Diesels using 2 piece rope-type rear seal. Shaft not splined on gear end. MF-1-44

66 1 ENGINES Replacement parts to fit Combine: 300 Industrial Tractor: 356, 302, 304, 3165 Tractor: MF65, MF165 AD4-203 Direct Injection 203 CID 4 Cylinder Perkins Diesel Standard Bore 3.6".150 Sleeve Flange Thickness Injectors at Angle in Cylinder Head 2 Piece rope-type rear seal TRU-POWER Engine Kits Used engine s/n to 29C1084 (.150" Sleeve Flange Thickness). For engines using 2 piece rope type rear seal. Engines bearings and thrust washers must be ordered separately M M91 Cylinder Parts Sleeve, CAST, replacing original CAST sleeve. Flange thickness.150". Replaces M1. Piston (w/pin), cupped head BEKP1467D-LCB EOK1467D-LCB BIFP1467D Basic engine kit. Contains sleeves, pistons, rings, pins, pin bushings, and overhaul gasket set with crankshaft seals. Engine overhaul kit. Contains sleeves, pistons, rings, pins, pin bushings, overhaul gasket set with crankshaft seals, valves, springs, guides, and keys. Basic in-frame kit. Contains sleeve and piston kit with rings, pins, and retainers, top engine gasket set, and oil pan gasket. Sleeve and Piston Kit M M1 Ring set, for 1 piston, used with CAST sleeves only. 3/32", 1/8", and 1/4" Bushing, piston pin (4 used per engine) Gaskets For engines using 2 piece rope-type rear seal, NOT for engines with DL in serial number ending. Crankshaft seals are included in engine kits but are not included in gasket sets M91 Top engine set M92 Bottom set, to engine s/n 29C1084. Complete for one engine. Used engine s/n & up. For engines originally produced with CAST sleeves. MFD4203PG Oil pan gasket. Crankshaft Seals PK467D Sleeve and piston kit. Contains CAST sleeves, flange thickness.150", piston and rings, pin and retainers M1 Seal, front, lip-type M1 Seal, rear, rope-type. For original production blocks (2 required) MF-1-45

67 1 ENGINES Combine: 300 Industrial Tractor: 356, 302, 304, 3165 Tractor: MF65, MF165 AD4-203 Direct Injection 203 CID 4 Cylinder Perkins Diesel Standard Bore 3.6".150 Sleeve Flange Thickness Injectors at Angle in Cylinder Head 2 Piece rope-type rear seal Valve Parts Main Bearing Kits 1 kit used per engine (Thrust washers not included) M91 Main bearing kit, standard VOKP203A M M M1 Valve overhaul kit. Contains intake and exhaust valves, springs, keys, and guides. Valve, intake (4 used per engine) Valve, exhaust Guide, intake & exhaust valve M M M91 Main bearing kit,.010" Main bearing kit,.020" Main bearing kit,.030" Thrust Washers M1 Spring, inner, intake & exhaust valve M1 Spring, outer, intake & exhaust valve M1 Retainer, valve spring M1 Key, intake & exhaust valves, pair (16 used per engine) Connecting Rod Bearing Kits M M1 Thrust washer, upper. 2 used per engine. Thrust washer, lower, tabbed. 2 used per engine. Crankshaft Kits 1 kit used per engine M91 Rod bearing kit, standard M M M91 Rod bearing kit,.010" Rod bearing kit,.020" Rod bearing kit,.030" M91 Crankshaft kit for A4-203 & AD4-203 Perkins Diesels using 2 piece rope-type rear seal. Shaft not splined on gear end. MF-1-46

68 1 ENGINES Replacement parts to fit Combine: 300 Industrial Tractor: 30, 302, 304, 3165, 356 Tractor Shovel, 40B, 50 Tractor: MF165, MF255, MF65 AD4-203 Direct Injection 203 CID 4 Cylinder Perkins Diesel Standard Bore 3.6".150 Sleeve Flange Thickness Injectors at Angle in Cylinder Head Valve spring count can vary, check cylinder head when disassembling BEKP2467-LCB TRU-POWER Engine Kits Used engine s/n 29C1084 & up. (.150" Sleeve Flange Thickness). For Engines using lip-type rear seal or 2 piece rope-type rear seal. Engine bearings and thrust washers must be ordered separately. Basic engine kit. Contains sleeves, pistons, rings, pins, pin bushings, and overhaul gasket set with crankshaft seals M1 Bushing, piston pin (4 used per engine) Gaskets EOK2467-LCB Engine overhaul kit. Contains sleeves, pistons, rings, pins, pin bushings, overhaul gasket set with crankshaft seals, valves, springs, guides, retainers, and keys. BIFP1467D PK467D Basic in-frame kit. Contains sleeve and piston kit with rings, pins, and retainers, top engine gasket set, and oil pan gasket. Sleeve and Piston Kit Complete for one engine. Used engine s/n & up. For engines originally produced with CAST sleeves. Sleeve and piston kit. Contains CAST sleeves, flange thickness.150", piston and rings, pin and retainers M M91 MFD4203PG Crankshaft seals are included in engine kits but are not included in gasket sets. Top engine set. Bottom set, engine s/n 29C1084 & up Oil pan gasket. Crankshaft Seals Cylinder Parts M M M91 Sleeve, CAST, replacing original CAST sleeve. Flange thickness.150". Replaces M1. Piston (w/pin), cupped head Ring set, for 1 piston, used with CAST sleeves only. 3/32", 1/8", and 1/4" M M M91 Seal, front, lip-type. Seal, rear, rope-type. For original production blocks (2 required) Seal, rear, lip-type (s/n 248UA123424L & up). For replacement blocks (2 required) MF-1-47

69 1 ENGINES Combine: 300 Industrial Tractor: 30, 302, 304, 3165, 356 Tractor Shovel, 40B, 50 Tractor: MF165, MF255, MF65 AD4-203 Direct Injection 203 CID 4 Cylinder Perkins Diesel Standard Bore 3.6".150 Sleeve Flange Thickness Injectors at Angle in Cylinder Head Valve spring count can vary, check cylinder head when disassembling Valve Parts Main Bearing Kits 1 kit used per engine (Thrust washers not included) M91 Main bearing kit, standard VOKP203A M M M1 Valve overhaul kit. Contains intake and exhaust valves, springs, keys, and guides. Valve, intake (4 used per engine) Valve, exhaust Guide, intake & exhaust valve M M M91 Main bearing kit,.010" Main bearing kit,.020" Main bearing kit,.030" Thrust Washers M1 Spring, inner, intake & exhaust valve M1 Spring, outer, intake & exhaust valve M1 Retainer, valve spring M1 Key, intake & exhaust valves, pair (16 used per engine) Connecting Rod Bearing Kits M M1 Thrust washer, upper. 2 used per engine. Thrust washer, lower, tabbed. 2 used per engine. Crankshaft Kits 1 kit used per engine M91 Crankshaft kit for A4-203 & AD4-203 Perkins Diesels using 2 piece rope-type rear seal. Shaft not splined on gear end M91 Rod bearing kit, standard M91 Rod bearing kit,.010" M91 Rod bearing kit,.020" M91 Rod bearing kit,.030" MF-1-48

70 1 ENGINES Replacement parts to fit Forklift: 6500 (prior to engine s/n 236UA109215L) Industrial Tractor: 31 Tractor: MF175, MF180, MF265 (prior to engine s/n 236UA109215L) A4-236 Direct Injection 236 CID 4 Cylinder Perkins Diesel Standard Bore 3.875" Injectors at Angle in Cylinder Head TRU-POWER Engine Kits Engine bearings and thrust washers must be ordered separately M1 Bushing, piston pin (4 used per engine) BEKP178-LCB Basic engine kit. Contains sleeves, pistons, rings, pins, pin bushings, and overhaul gasket set with crankshaft seals. Gaskets EOK178-LCB Engine overhaul kit. Contains sleeves, pistons, rings, pins, pin bushings, overhaul gasket set with crankshaft seals, valves, springs, and keys. BIFP178 Basic in-frame kit. Contains sleeve and piston kit with rings, pins and retainers, top engine gasket set, and oil pan gasket. Sleeve & Piston Kit Crankshaft seals are included in engine kits but are not included in gasket sets M91 Top engine set M91 Bottom engine set M1 Oil pan gasket. Complete for 1 engine Crankshaft Seals PK78 Sleeve and piston kit. Contains sleeves, piston and rings, pin and retainers M1 Seal, front, lip-type. Cylinder Parts M M91 Cylinder liner. Piston with pin; Oil groove holes 10 top, 12 bottom M91 Seal, rear, lip-type (s/n 248UA123424L & up). For replacement blocks (2 required) M91 Ring set, for 1 piston. Can replace M91 & M91. 3/32", 1/4" M1 Seal, rear, rope-type, 2 required (prior to s/n 248UA123424L) *Both rear seal types included in engine kits MF-1-49

71 1 ENGINES Forklift: 6500 (prior to engine s/n 236UA109215L) Industrial Tractor: 31 Tractor: MF175, MF180, MF265 (prior to engine s/n 236UA109215L) A4-236 Direct Injection 236 CID 4 Cylinder Perkins Diesel Standard Bore 3.875" Injectors at Angle in Cylinder Head Valve Parts Main Bearing Kits 1 kit used per engine (Thrust washers not included) M91 Main bearing kit, standard VOKP M M M91 Valve overhaul kit. Contains intake and exhaust valves, springs, and keys. Valve, intake Valve, exhaust, stellite. Replaces M1. Spring, inner, intake & exhaust valve M M M91 Main bearing kit,.010" Main bearing kit,.020" Main bearing kit,.030" Thrust Washers M1 Spring, outer, intake & exhaust valve M1 Key, intake & exhaust valve (pair) Connecting Rod Bearing Kits Thrust washer, upper. 2 used per engine. Prior to engine s/n , MF175, MF180 only (lower washer tab on-center). 1 kit used per engine. Thrust washer, lower, 2 used per engine. Prior to engine s/n , MF175, MF180 only (lower washer tab on-center) M M M91 Rod bearing kit, standard Rod bearing kit,.010" Rod bearing kit,.020" M1 Thrust washer, upper. 2 used per engine. MF175, MF180, engine s/n and up, All MF265, 31C, 6500 forklift. (lower washer tab off-center) M1 Thrust washer, lower, tabbed. 2 used per engine. MF175, MF180, engine s/n and up, All MF265, 31C, 6500 forklift. (lower washer tab off-center) MF-1-50

72 1 ENGINES Replacement parts to fit Forklift: 6500 (engine s/n 236UA109215L & up) Industrial Tractor: 50C Tractor: MF255, MF265 (engine s/n 236UA109215L & up) A4-236 Direct Injection 236 CID 4 Cylinder Perkins Diesel Standard Bore 3.875" Injectors at Angle in Cylinder Head TRU-POWER Engine Kits Engine bearings and thrust washers must be ordered separately. Gaskets BEKP2178-LCB Basic engine kit. Contains sleeves, pistons, rings, pins, pin bushings, and overhaul gasket set with crankshaft seals. EOK2178-LCB Engine overhaul kit. Contains sleeves, pistons, rings, pins, pin bushings, overhaul gasket set with crankshaft seals, valves, springs, and keys. Crankshaft seals are included in engine kits but are not included in gasket sets. BIFP2178 Basic in-frame kit. Contains sleeve and piston kit with rings, pins, and retainers, top engine gasket set, and oil pan gasket. Sleeve & Piston Kit M M M1 Top engine set. Bottom engine set. Oil pan gasket. Crankshaft Seals M1 Seal, front, lip-type. PK79 Sleeve and piston kit. Contains sleeves, piston and rings, pin and retainers. Cylinder Parts M1 Seal, rear, rope-type, 2 required (prior to s/n 248UA123424L) M M91 Cylinder liner. Piston w/pin; oil groove holes 8 top, 8 bottom M91 Seal, rear, lip-type (s/n 248UA123424L & up). For replacement blocks (2 required) *Both rear seal types included in engine kits M91 Ring set, for 1 piston. Can replace M91 & M91. 3/32", 1/4" M1 Bushing, piston pin (4 used per engine) MF-1-51

73 1 ENGINES Forklift: 6500 (engine s/n 236UA109215L & up) Industrial Tractor: 50C Tractor: MF255, MF265 (engine s/n 236UA109215L & up) A4-236 Direct Injection 236 CID 4 Cylinder Perkins Diesel Standard Bore 3.875" Injectors at Angle in Cylinder Head Valve Parts Main Bearing Kits 1 kit used per engine (Thrust washers not included) M91 Main bearing kit, standard VOKP M M M91 Valve overhaul kit. Contains intake and exhaust valves, springs, and keys. Valve, intake Valve, exhaust, stellite. Replaces M1. Spring, inner, intake & exhaust valve M M M91 Main bearing kit,.010" Main bearing kit,.020" Main bearing kit,.030" Thrust Washers M1 Spring, outer, intake & exhaust valve M1 Key, intake & exhaust valve (pair) Connecting Rod Bearing Kits M1 Thrust washer, upper. 2 used per engine. MF175, MF180, engine s/n and up, All MF265, 31C, 6500 forklift. (lower washer tab off-center) M M91 1 kit used per engine. Rod bearing kit, standard Rod bearing kit,.010" M1 Thrust washer, lower, tabbed. 2 used per engine. MF175, MF180, engine s/n and up, All MF265, 31C, 6500 forklift. (lower washer tab off-center) M91 Rod bearing kit,.020" MF-1-52

74 1 ENGINES Replacement parts to fit Tractor: MF275 A4-248 Direct Injection 248 CID 4 Cylinder Perkins Diesel Standard Bore 3.978" Engine Serial Number: Prefix 248UA or LF---N or LF---U only Injectors at Angle in Cylinder Head BEKP4248-LCB TRU-POWER Engine Kits Engine bearings and thrust washers must be ordered separately. Basic engine kit. Contains sleeves, pistons, rings, pins, pin bushings, and overhaul gasket set with crankshaft seals. Gaskets Crankshaft seals are included in engine kits but are not included in gasket sets. EOK4248-LCB BIFP4248 Engine overhaul kit. Contains sleeves, pistons, rings, pins, pin bushings, overhaul gasket set with crankshaft seals, valves, springs, and keys. Basic in-frame kit. Contains sleeve and piston kit with rings, pins and retainers, top engine gasket set, and oil pan gasket. Sleeve & Piston Kit M M M M1 Top engine set. Bottom engine set. Oil pan gasket. Crankshaft Seals Seal, front, lip-type. Complete for 1 engine M1 Seal, rear, rope-type, 2 required (prior to s/n 248UA123424L) PK4248 Sleeve and piston kit. Contains sleeve, piston and rings, pins and retainers, complete for 4 cylinders. Sleeves replace Perkins # , pistons replace Perkins # Cylinder Parts M91 Seal, rear, lip-type (s/n 248UA123424L & up). For replacement blocks (2 required) M1 Cylinder sleeve, replace *Both rear seal types included in EOK and BEK M91 Ring set, for 1 piston. 3/32", 1/4" M1 Bushing, piston pin (4 used per engine) MF-1-53

75 1 ENGINES Tractor: MF275 A4-248 Direct Injection 248 CID 4 Cylinder Perkins Diesel Standard Bore 3.978" Engine Serial Number: Prefix 248UA or LF---N or LF---U only Injectors at Angle in Cylinder Head Valve Parts Main Bearing Kits VOKP M M M M M1 Valve overhaul kit. Contains intake and exhaust valves, springs, and keys. Valve, intake Valve, exhaust, stellite. Replaces M1. Spring, inner, intake & exhaust valve Spring, outer, intake & exhaust valve Key, intake & exhaust valve (pair) M M M M91 1 kit used per engine (Thrust washers not included) Main bearing kit, standard Main bearing kit,.010" Main bearing kit,.020" Main bearing kit,.030" Thrust Washers Connecting Rod Bearing Kits M1 Thrust washer, upper. 2 used per engine. MF175, MF180, engine s/n and up, All MF265, 31C, 6500 forklift. (lower washer tab off-center) M M91 1 kit used per engine. Rod bearing kit, standard Rod bearing kit,.010" M1 Thrust washer, lower, tabbed. 2 used per engine. MF175, MF180, engine s/n and up, All MF265, 31C, 6500 forklift. (lower washer tab off-center) M91 Rod bearing kit,.020" MF-1-54

76 1 ENGINES Replacement parts to fit Tractor: MF290, MF294-4, MF690 A4-248 Direct Injection 248 CID 4 Cylinder Perkins Diesel Standard Bore 3.978" Engine Serial Number: Prior to LF---U839080J Injectors at Angle in Cylinder Head TRU-POWER Engine Kits Engine bearings and thrust washers must be ordered separately. Gaskets BEKP4248A-LCB Basic engine kit. Contains sleeves, pistons, rings, pins, pin bushings, and overhaul gasket set with crankshaft seals. EOK4248A-LCB BIFP4248A Engine overhaul kit. Contains sleeves, pistons and rings, pins and retainers, pin bushings, gasket sets, crankshaft seals, intake and exhaust valves, valve keys and springs. Basic in-frame kit. Contains sleeves, pistons, rings, pins, valve grind set, and oil pan gasket. Sleeve & Piston Kit M M M1 Crankshaft seals are included in engine kits but are not included in gasket sets. Top engine set. Bottom engine set. Oil pan gasket. Crankshaft Seals M1 Seal, front, lip-type. PK4248 Complete for 1 engine Sleeve and piston kit. Contains sleeve, piston and rings, pins and retainers, complete for 4 cylinders. Sleeves replace Perkins # , pistons replace Perkins # Cylinder Parts M91 Seal, rear, lip-type (s/n 248UA123424L & up). For replacement blocks (2 required) Valve Parts M1 Cylinder sleeve, replace M91 Ring set, for 1 piston. 3/32", 1/4" VOKP M1 Valve overhaul kit. Contains intake and exhaust valves, springs, and keys. Valve, intake M1 Bushing, piston pin (4 used per engine) M M91 Valve, exhaust, stellite. Replaces M1. Spring, inner, intake & exhaust valve M1 Spring, outer, intake & exhaust valve M1 Key, intake & exhaust valve (pair) MF-1-55

77 1 ENGINES Tractor: MF290, MF294-4, MF690 A4-248 Direct Injection 248 CID 4 Cylinder Perkins Diesel Standard Bore 3.978" Engine Serial Number: Prior to LF---U839080J Injectors at Angle in Cylinder Head Connecting Rod Bearing Kits Thrust Washers 1 kit used per engine M1 Thrust washer, upper. 2 used per engine. MF175, MF180, engine s/n and up, All MF265, 31C, 6500 forklift. (lower washer tab off-center) M M M91 Rod bearing kit, standard Rod bearing kit,.010" Rod bearing kit,.020" M1 Thrust washer, lower, tabbed. 2 used per engine. MF175, MF180, engine s/n and up, All MF265, 31C, 6500 forklift. (lower washer tab off-center) Main Bearing Kits 1 kit used per engine (Thrust washers not included) M91 Main bearing kit, standard M91 Main bearing kit,.010" M91 Main bearing kit,.020" M91 Main bearing kit,.030" MF-1-56

78 1 ENGINES Replacement parts to fit Combine: 540 Tractor: MF1080, MF1085, MF285 A4-318 Direct Injection 318 CID 4 Cylinder Perkins Diesel Standard Bore 4.5" Injectors at Angle in Cylinder Head BEKP4318-LCB TRU-POWER Engine Kits Engine bearings and thrust washers must be ordered separately. Basic engine kit. Contains sleeves, pistons, rings, pins, pin bushings, and overhaul gasket set with crankshaft seals. Gaskets Crankshaft seals are included in engine kits but are not included in gasket sets. EOK4318-LCB BIFP4318 Engine overhaul kit. Contains sleeves, pistons, rings, pins, pin bushings, overhaul gasket set with crankshaft seals, valves, springs, guides, and keys. Basic in-frame kit. Contains sleeve and piston with rings, pins and retainers, top engine gasket set, and oil pan gasket. Sleeve & Piston Kit M M M M1 Top set, with head gasket /745730M1 Bottom set. Oil pan gasket. Crankshaft Seals Seal, front, lip-type M1 Seal, rear, rope-type, 2 required (prior to s/n 248UA123424L) Complete for 1 engine PK80 Sleeve and piston kit. Contains sleeves, pistons and rings, pins and retainers, complete for 4 cylinders M91 Seal, rear, lip-type (s/n 248UA123424L & up). For replacement blocks (2 required) Cylinder Parts Cylinder sleeve M M1 Ring set, for 1 piston. 3/32", 1/4" Bushing, piston pin (4 used per engine) MF-1-57

79 1 ENGINES Combine: 540 Tractor: MF1080, MF1085, MF285 A4-318 Direct Injection 318 CID 4 Cylinder Perkins Diesel Standard Bore 4.5" Injectors at Angle in Cylinder Head Valve Parts Main Bearing Kits 1 kit used per engine (Thrust washers not included) M91 Main bearing kit, standard VOKP M M M1 Valve overhaul kit. Contains intake and exhaust valves, springs, keys, and guides. Valve, engine intake Valve, engine exhaust Guide, intake & exhaust valves M M M91 Main bearing kit,.010" Main bearing kit,.020" Main bearing kit,.030" Thrust Washers M91 Spring, inner, intake & exhaust valve M1 Spring, outer, intake & exhaust valve M1 Key, intake & exhaust valve (pair) Connecting Rod Bearing Kits M1 Thrust washer, upper. 2 used per engine. MF175, MF180, engine s/n and up, All MF265, 31C, 6500 forklift. (lower washer tab off-center) M91 1 kit used per engine. Rod bearing kit, standard M1 Thrust washer, lower, tabbed. 2 used per engine. MF175, MF180, engine s/n and up, All MF265, 31C, 6500 forklift. (lower washer tab off-center) M91 Rod bearing kit,.010" M91 Rod bearing kit,.020" MF-1-58

80 1 ENGINES Replacement parts to fit Tractor: MF1100 A6-354 Non-Turbo 354 CID 6 Cylinder Perkins Diesel Standard Bore 3.875" Engine Serial Number: Prior to 354UA3515 Piston pin 1-3/8" dia. Head gasket replaces MF/Perkins and Valve cover uses 6 bolts 2 Piece rope-type rear seal BEKP2316A-LCB EOK2316A-LCB TRU-POWER Engine Kits Engine bearings and thrust washers must be ordered separately. Basic engine kit. Contains sleeves, pistons, rings, pins, pin bushings, and overhaul gasket set with crankshaft seals. Engine overhaul kit. Contains sleeves, pistons, rings, pins, pin bushings, overhaul gasket set with crankshaft seals, valves, springs, guides, and keys M M M1 Cylinder Parts Cylinder liner. Ring set, for 1 piston. Can replace M91 & M91. 3/32", 1/4" Bushing, piston pin (6 used per engine) BIFP2316A Basic in-frame kit. Contains sleeves, pistons, rings, pins, valve grind set, and oil pan gasket kit. Gaskets Sleeve & Piston Kit PK316 Complete for 1 engine 1-3/8" piston pin diameter Sleeve and piston kit. Contains sleeves, pistons, pins, retainers, top chrome and bottom oil control ring set. For 3-7/8" standard bore. HS8279 CS M1 Head gasket replaces MF/Perkins # and # Valve covers use 6 bolts. Crankshaft seals are included in engine kits. Bottom gasket set includes the 2 piece rope-type rear seal. Top gasket set. Can replace Perkins Bottom gasket set. Replaces Perkins U5LB0020. Oil pan gasket. Crankshaft Seals M1 Seal, front, lip-type M1 Seal, rear, rope-type, 2 required (prior to s/n 248UA123424L) MF-1-59

81 1 ENGINES Tractor: MF1100 A6-354 Non-Turbo 354 CID 6 Cylinder Perkins Diesel Standard Bore 3.875" Engine Serial Number: Prior to 354UA3515 Piston pin 1-3/8" dia. Head gasket replaces MF/Perkins and Valve cover uses 6 bolts 2 Piece rope-type rear seal Valve Parts Main Bearing Kits VOKP M M M M M M1 Valve overhaul kit. Contains intake and exhaust valves, springs, keys, and guides. Valve, intake Valve, exhaust, stellite. Replaces M1. Guide, intake Guide, exhaust Spring, inner, intake & exhaust valve Spring, outer, intake & exhaust valve M M M91 1 kit used per engine (Thrust washers not included) Main bearing kit, standard Main bearing kit,.010" Main bearing kit,.020" Thrust Washers Upper thrust washer. 2 used prior to engine s/n M1 Key, intake & exhaust valve (pair) Connecting Rod Bearing Kits Lower thrust washer. 2 used prior to engine s/n Tab on-center M1 Upper thrust washer. 2 used engine s/n & up. 1 kit used per engine M1 Lower thrust washer, tab off-center. 2 used engine s/n & up M91 Rod bearing kit, standard M91 Rod bearing kit,.010" M91 Rod bearing kit,.020" MF-1-60

82 1 ENGINES Replacement parts to fit Tractor: MF1100 A6-354 Non-Turbo 354 CID 6 Cylinder Perkins Diesel Standard Bore 3.875" Engine Serial Number: 354UA UA10361 Piston pin 1-3/8" dia. Head gasket replaces MF/Perkins and Valve cover uses 14 bolts 2 Piece rope-type rear seal BEKP2316B-LCB EOK2316B-LCB TRU-POWER Engine Kits Engine bearings and thrust washers must be ordered separately. Basic engine kit. Contains sleeves, pistons, rings, pins, pin bushings, and overhaul gasket set with crankshaft seals. Engine overhaul kit. Contains sleeves, pistons, rings, pins, pin bushings, overhaul gasket set with crankshaft seals, valves, springs, guides, and keys M M M1 Cylinder Parts Cylinder liner. Ring set, for 1 piston. Can replace M91 & M91. 3/32", 1/4" Bushing, piston pin (6 used per engine) BIFP2316B Basic in-frame kit. Contains sleeves, pistons, rings, pins, valve grind set, and oil pan gasket kit. Gaskets Sleeve & Piston Kit PK316 Complete for 1 engine 1-3/8" piston pin diameter Sleeve and piston kit. Contains sleeves, pistons, pins, retainers, top chrome and bottom oil control ring set. For 3-7/8" standard bore. HS8280 CS M1 Head gasket replaces MF/Perkins # and # Valve covers use 14 bolts. Crankshaft seals are included in engine kits. Bottom gasket set includes the 2 piece rope type rear seal. Top gasket set. Can replace Perkins Bottom gasket set. Replaces Perkins U5LB0020. Oil pan gasket. Crankshaft Seals M1 Seal, front, lip-type M1 Seal, rear, rope-type, 2 required (prior to s/n 248UA123424L) MF-1-61

83 1 ENGINES Tractor: MF1100 A6-354 Non-Turbo 354 CID 6 Cylinder Perkins Diesel Standard Bore 3.875" Engine Serial Number: 354UA UA10361 Piston pin 1-3/8" dia. Head gasket replaces MF/Perkins and Valve cover uses 14 bolts 2 Piece rope-type rear seal Valve Parts Main Bearing Kits VOKP M M M M M M1 Valve overhaul kit. Contains intake and exhaust valves, springs, keys, and guides. Valve, intake Valve, exhaust, stellite. Replaces M1. Guide, intake Guide, exhaust Spring, inner, intake & exhaust valve Spring, outer, intake & exhaust valve M M M91 1 kit used per engine (Thrust washers not included) Main bearing kit, standard Main bearing kit,.010" Main bearing kit,.020" Thrust Washers Upper thrust washer. 2 used prior to engine s/n M1 Key, intake & exhaust valve (pair) Connecting Rod Bearing Kits Lower thrust washer. 2 used prior to engine s/n Tab on-center M1 Upper thrust washer. 2 used engine s/n & up. 1 kit used per engine M1 Lower thrust washer, tab off-center. 2 used engine s/n & up M91 Rod bearing kit, standard M91 Rod bearing kit,.010" M91 Rod bearing kit,.020" MF-1-62

84 1 ENGINES Replacement parts to fit Tractor: MF1100 A6-354 Non-Turbo 354 CID 6 Cylinder Perkins Diesel Standard Bore 3.875" Engine Serial Number: 354UA10362 and up Piston pin 1-3/8" dia. Head gasket replaces MF/Perkins and Valve cover uses 14 bolts 2 Piece rope-type rear seal BEKP3316-LCB EOK3316-LCB TRU-POWER Engine Kits Engine bearings and thrust washers must be ordered separately. Basic engine kit. Contains sleeves, pistons, rings, pins, pin bushings, and overhaul gasket set with crankshaft seals. Engine overhaul kit. Contains sleeves, pistons, rings, pins, pin bushings, overhaul gasket set with crankshaft seals, valves, springs, guides, and keys M M M1 Cylinder Parts Cylinder liner. Ring set, for 1 piston. Can replace M91 & M91. 3/32", 1/4" Bushing, piston pin (6 used per engine) BIFP3316 Basic in-frame kit. Contains sleeves, pistons, rings, pins, valve grind set, and oil pan gasket set. Gaskets Sleeve & Piston Kit Complete for 1 engine 1-3/8" piston pin diameter HS2605 Head gasket replaces MF/Perkins # and # Valve covers use 14 bolts. Crankshaft seals are included in engine kits. Bottom gasket set includes the 2 piece rope type rear seal. Top gasket set. Can replace Perkins 69005/U5LT0026. PK316 Sleeve and piston kit. Contains sleeves, pistons, pins, retainers, top chrome and bottom oil control ring set. For 3-7/8" standard bore. CS M1 Bottom gasket set. Replaces Perkins U5LB0020. Oil pan gasket. Crankshaft Seals M1 Seal, front, lip-type M1 Seal, rear, rope-type, 2 required (prior to s/n 248UA123424L) MF-1-63

85 1 ENGINES Tractor: MF1100 A6-354 Non-Turbo 354 CID 6 Cylinder Perkins Diesel Standard Bore 3.875" Engine Serial Number: 354UA10362 and up Piston pin 1-3/8" dia. Head gasket replaces MF/Perkins and Valve cover uses 14 bolts 2 Piece rope-type rear seal Valve Parts Main Bearing Kits VOKP M M M M M M1 Valve overhaul kit. Contains intake and exhaust valves, springs, keys, and guides. Valve, intake Valve, exhaust, stellite. Replaces M1. Guide, intake Guide, exhaust Spring, inner, intake & exhaust valve Spring, outer, intake & exhaust valve M M M91 1 kit used per engine (Thrust washers not included) Main bearing kit, standard Main bearing kit,.010" Main bearing kit,.020" Thrust Washers Upper thrust washer. 2 used prior to engine s/n M1 Key, intake & exhaust valve (pair) Connecting Rod Bearing Kits Lower thrust washer. 2 used prior to engine s/n Tab on-center M1 Upper thrust washer. 2 used engine s/n & up. 1 kit used per engine M1 Lower thrust washer, tab off-center. 2 used engine s/n & up M91 Rod bearing kit, standard M91 Rod bearing kit,.010" M91 Rod bearing kit,.020" MF-1-64

86 1 ENGINES Replacement parts to fit Tractor: MF1130 AT6-354 Turbo 354 CID 6 Cylinder Perkins Turbocharged Diesel Standard Bore 3.875" Engine Serial Number: Engine s/n prior to 354UA3356T Piston pin 1-1/2" dia. Head gasket replaces MF/Perkins Piece rope-type rear seal BEKP183A-LCB TRU-POWER Engine Kits Engine bearings and thrust washers must be ordered separately. Basic engine kit. Contains sleeves, pistons, rings, pins, pin bushings, and overhaul gasket set with crankshaft seals M M91 Cylinder Parts Cylinder liner. Piston w/pin. EOK183A-LCB Engine overhaul kit. Contains sleeves, pistons, rings, pins, pin bushings, overhaul gasket set with crankshaft seals, valves, springs, guides, and keys M91 Ring set, for 1 piston. 1/8", 3/32", 1/4" BIFP183A Basic in-frame kit. Contains sleeves, pistons, rings, pins, valve grind set, and oil pan gasket kit M1 Bushing, piston pin (6 used per engine) Sleeve & Piston Kit Gaskets Complete for 1 engine Head Gasket replaces MF/Perkins # Crankshaft seals are included in engine kits. Bottom gasket set includes the 2 piece rope type rear seal. PK83 1-1/2" piston pin diameter 1 used per engine Sleeve and piston kit. Contains sleeves, pistons and rings, pins and retainers, complete for 6 cylinders. HS8291 CS M1 Top gasket set. Can replace Perkins Bottom gasket set. Replaces Perkins U5LB0020. Oil pan gasket. Crankshaft Seals M1 Seal, front, lip-type M1 Seal, rear, rope-type, 2 required (prior to s/n 248UA123424L) MF-1-65

87 1 ENGINES Tractor: MF1130 AT6-354 Turbo 354 CID 6 Cylinder Perkins Turbocharged Diesel Standard Bore 3.875" Engine Serial Number: Engine s/n prior to 354UA3356T Piston pin 1-1/2" dia. Head gasket replaces MF/Perkins Piece rope-type rear seal Valve Parts Main Bearing Kits 1 kit used per engine (Thrust washers not included) M1 Main bearing kit, standard VOKP M M M M91 Valve overhaul kit. Contains intake and exhaust valves, springs, keys, and guides. Valve, intake Valve, exhaust, stellite. Replaces M1. Guide, intake Spring, inner, intake & exhaust valve M M M1 Main bearing kit,.010" Main bearing kit,.020" Thrust Washers Upper thrust washer. 2 used engine s/n & up M1 Spring, outer, intake & exhaust valve M M1 Guide, exhaust Key, intake & exhaust valve (pair) Connecting Rod Bearing Kits M1 Lower thrust washer, tab off-center. 2 used engine s/n & up. 1 kit used per engine M91 Rod bearing kit, standard M91 Rod bearing kit,.010" M91 Rod bearing kit,.020" MF-1-66

88 1 ENGINES Replacement parts to fit Combine: 750 (to s/n ), 760 (to s/n ) Tractor: MF1105, MF1130 (engine s/n 354UA3356T & up), MF1135 AT6-354 Turbo 354 CID 6 Cylinder Perkins Turbocharged Diesel Standard Bore 3.875" Piston pin 1-1/2" dia. BEKP183B-LCB TRU-POWER Engine Kits Engine bearings and thrust washers must be ordered separately. Basic engine kit. Contains sleeves, pistons, rings, pins, pin bushings, and overhaul gasket set with crankshaft seals M M91 Cylinder Parts Cylinder liner. Piston w/pin. EOK183B-LCB Engine overhaul kit. Contains sleeves, pistons, rings, pins, pin bushings, overhaul gasket set with crankshaft seals, valves, springs, guides, and keys M91 Ring set, for 1 piston. 1/8", 3/32", 1/4" BIFP183B Basic in-frame kit. Contains sleeves, pistons, rings, pins, valve grind set, and oil pan gasket kit M1 Bushing, piston pin (6 used per engine) Sleeve & Piston Kit Gaskets Complete for 1 engine HS2605 Top gasket set. Can replace Perkins 69005/U5LT0026. PK83 1-1/2" piston pin diameter 1 used per engine Sleeve and piston kit. Contains sleeves, pistons and rings, pins and retainers, complete for 6 cylinders. CS M1 Bottom gasket set. Can replace Perkins U5LB0024. Oil pan gasket. MF-1-67

89 1 ENGINES Combine: 750 (to s/n ), 760 (to s/n ) Tractor: MF1105, MF1130 (engine s/n 354UA3356T & up), MF1135 AT6-354 Turbo 354 CID 6 Cylinder Perkins Turbocharged Diesel Standard Bore 3.875" Piston pin 1-1/2" dia. Crankshaft Seals Connecting Rod Bearing Kits M1 Seal, front, lip-type M1 Seal, rear, rope-type, 2 required (prior to s/n 248UA123424L) M91 1 kit used per engine. Rod bearing kit, standard M91 Rod bearing kit,.010" M91 Seal, rear, lip-type (s/n 248UA123424L & up). For replacement blocks (2 required) M91 Rod bearing kit,.020" Main Bearing Kits Valve Parts 1 kit used per engine (Thrust washers not included) M1 Main bearing kit, standard M1 Main bearing kit,.010" M91 Main bearing kit,.020" VOKP M1 Valve overhaul kit. Contains intake and exhaust valves, springs, keys, and guides. Valve, intake M1 Thrust Washers Upper thrust washer. 2 used engine s/n & up M1 Valve, exhaust, stellite. Replaces M M M M91 Guide, intake Guide, exhaust Spring, inner, intake & exhaust valve M1 Lower thrust washer, tab off-center. 2 used engine s/n & up M1 Spring, outer, intake & exhaust valve M1 Key, intake & exhaust valve (pair) MF-1-68

90 1 ENGINES Replacement parts to fit 354 CID 6 Cylinder Perkins Diesel Standard Bore 3.875" A Non-Turbo Perkins Diesel AT Turbo Perkins Diesel Connecting Rod Bearing Kits Thrust Washers M91 1 kit used per engine. Rod bearing kit, standard. For AT only Main Bearing Kits M M1 Thrust washer, upper. 2 used per engine. MF175, MF180, engine s/n and up, All MF265, 31C, 6500 forklift. (lower washer tab off-center) Thrust washer, lower, tabbed. 2 used per engine. MF175, MF180, engine s/n and up, All MF265, 31C, 6500 forklift. (lower washer tab off-center) 1 kit used per engine (Thrust washers not included) M91 Main bearing kit, standard MF-1-69

91 1 ENGINES Combine: Super 92 A6-305 Regular Injection 305 CID 6 Cylinder Perkins Diesel Standard Bore 3.6" Injectors Vertical in Head Cylinder Parts Valve Parts M-CST Sleeve, CAST, for replacing original CHROME sleeve. Flange thickness.040" M1 Sleeve, CAST, replacing original CAST sleeve. Flange thickness.150". Replaces M M91 Piston with pin, flat head M1 Valve, intake M1 Valve, exhaust PRS334DC M91 Ring set for 3 pistons only, use with CHROME sleeves, can replace M92. 3/32", 1/8", 1/4". Ring set, for 1 piston, used with CAST sleeves only. 3/32", 1/8", and 1/4" M M M1 Spring, inner, intake & exhaust valve Spring, outer, intake & exhaust valve Key, intake & exhaust valve (12 used per engine) Thrust Washers M M1 Bushing, piston pin (6 used per engine) Crankshaft Seals Seal, rear, rope-type. For original production blocks (2 required) M M1 Thrust washer, upper. 2 used per engine. Thrust washer, lower, tabbed. 2 used per engine. MF-1-70

92 1 ENGINES Replacement parts to fit Crankshaft Kits Timing Gears (Standard) M91 Crankshaft kit, new, with standard rod bearings, main bearings, & thrust washers. For Perkins AG3-152 gas, A3-152 & AD3-152 diesels. Uses 2 piece rope-type rear seal. 1/2" wide flywheel flange M1 Crankshaft gear, 24 teeth. For Continental gas engine in tractors: TE20, TO20, TO M M91 Crankshaft kit, new, with standard size rod & main bearings, & thrust washers. For Perkins AG3-152 gas & AD3-152 diesel engines using 1 piece lip-type rear seal, keyed nose, 1-1/2" wide flywheel flange. Replaces U5BG0027, M91, M91, M91. Crankshaft kit for A4-203 & AD4-203 Perkins Diesels using 2 piece rope-type rear seal. Shaft not splined on gear end M1 Crankshaft gear, 24 teeth. For Continental gas engine in tractors: TO35, MF35, MF50, MH50, MF135, MF150. Z129CK Crankshaft kit with standard size rod & main bearings. For Z129 Continental gas engine in tractors: TO30 with thrust on front main. Z134CK Crankshaft kit with standard size rod & main bearings. For Z134 Continental gas engine in tractors: TO30 late with thrust on center main, TO35, MF35, MF135; industrial: M1 Camshaft gear, 48 teeth. For Continental gas engine in tractors: TE20, TO20, TO30, TO35, F40, MH50, MF50, MF135, MF150; industrials: 202, 204, Camshafts M91 Camshaft, for Continental gas engines Z120, Z129, Z tooth, 1.125" gear. Tractors: TE20, TO20, TO30, TO35, MF35, F40, MH50, MF50, MF135 Special; industrials: 202, 204, Replaces M1, M M1 Camshaft with nut, 10 tooth, 1.234" gear. For Continental Z145 gas engine in tractors: MF135, MF150, MF230, MF235, MF245; industrials: 20C, 30B; forklifts: 2500, MF-1-71

93 1 ENGINES Cylinder Heads Oil Pump Repair Kits M91 Cylinder head assembly, for Perkins A3-152 regular injection engine (injectors vertical in cylinder head). Head assembly includes valves & valve parts. Tractors: MF35, MF50; industrials: 35 utility, 203, 205. Replaces ZZ080058, M91. OPK60A Oil pump repair kit. For Continental engine in tractors: TE20, TO20, TO30, TO35, MF35, MF135, MF50, MF150. Replaces M91. Drive gear is 2-15/16" O.D M91 Cylinder head assembly, for Perkins AD3-152 direct injection engines (injectors at angle in cylinder head). Includes valves & valve parts. For tractors: MF135, MF150, MF230, MF235, MF245; industrials: 20, 20C 30B, 30D, 40, 203, 205, 2135, 2200 treever; forklifts: 2200, 2500, 4500; crawlers: 200, 200B, 200C, Replaces cylinder heads M91, M91, M91, these heads have valves with a 45 degree face angle & are no longer supplied by OEM M91 is the same as supplied by the OEM & has valves with a 35 degree face angle. Replaces ZZ080082, ZZ080025, M91. OPK65A TW1314S Oil pump repair kit. For Continental engine in tractors: MF65, MF165, MF175, MF180. Drive gear is 3-1/8" O.D. Thrust Washers Thrust washer set. Contains DI733713M1 (upper) and DI733714M1 (lower). Tractors: MF175, MF180 (prior to engine s/n ). Oil Pumps For Perkins Engines M91 Oil pump assembly. Tractors: MF35, MF50, MF135, MF230, MF235, MF245, others using A3-152 & AD3-152 engines, gas and diesel M91 Oil pump assembly. Tractors: MF65, MF165, MF255; industrials: 30, 40B, 50, 302, 304, 3165; combine: 300 S.P.; using A4-203 & AD4-203, gas & diesel. Replaces , M91. MF-1-72

94 2 ENGINE SYSTEMS Replacement parts to fit Carburetors & Carburetor Repair Kits For tractor models using Continental gas engine. Application Tractor: TE20, TO20, TO30 Carburetor M91 Industrial Tractor: 202, 204, M Tractor: TO35, F40, MH50, MF50, MF135, MF150 Tractor: MF M91 Forklift: M92 Industrial Tractor: 2135 Tractor: MF135, MF150 Industrial Tractor: M92 Tractor: MF165 Carb Manufacture Carb Manufacture Tractor Manufacture Numbers Carb Numbers Marvel-Schebler TS458, TS361A, n/a Marvel-Schebler n/a, TS605, TS683, TS882 Zenith Zenith Zenith M91, M91, C549V M M91, M91, C549AV M91, M m91 (TS695) M91 (TS882) M91 (TS884) Complete Basic Repair Kit Repair Kit BK48V BK49V Gasket Kit CGK32 CGK32 K2127 K2112 K2127 Application Complete Carb Manufacture Carb Manufacture Repair Kit Numbers Tractor: TE20, TO20 C548V Marvel-Schebler TS361A, n/a Tractor: TO20, TO30 C549V Marvel-Schebler TS458 Industrial Tractor: 202, 204, C549AV Marvel-Schebler TS605, TS683, 2135 TS882, N/A Tractor: TO35, F40, MH50, MF50, MF135, MF150 Industrial Tractor: 202, 204, Carter UT2223S, UT2418S 2135 Tractor: TO35, F40, MH44, MH44K, MH50, MF50, MH444 Zenith 62AJ9/10444, 62AJ/10279A Tractor: MF85, MF88 Marvel-Schebler TS644, TS786-1 Industrial Tractor: 3165 C549BV Marvel-Schebler TS695, TS884 Tractor: MF65, MF165 Tractor: MF175 Marvel-Schebler TS893, TS916 Tractor Manufacture Carb Numbers M91, M M M91, M91, M91, M M91, M M91, 6809A Basic Repair Gasket Kit Kit BK48V CGK32 BK48V CGK32 BK49V CGK32 BK201V BK87V M91, M91 BK M91, M92 BK49BV M91, M91 BK49BV CGK26 CGK34 CGK34 MF-2-73

95 2 ENGINE SYSTEMS K2112 K2136 Carburetor Tune-up Kit Carburetor tune-up kit contains: valve & seat, idle adjusting needle, and necessary gaskets, seals, bushings, plugs, washers, float pin, and instructions for carburetor repair. Used In A Wide Range Of Other OEM Equipment Tune-up kit for Zenith carburetors used in various Massey Ferguson equipment. Services the following carburetor models: Tune-up kit for Zenith carburetors used in various Massey Ferguson equipment. Services the following carburetor models: K2127 Carburetor tune-up kit for Zenith carburetors used in various Massey Ferguson equipment. Services the following carburetor models: OS Throttle Body Repair Bushings Designed to bush worn throttle bodies. T818 Upper bushing, 1/4" shafts. OD.383", ID.247", L.501". T819 Lower bushing, 1/4" shafts. OD.323", ID.247", L.471". MF-2-74

96 2 ENGINE SYSTEMS Replacement parts to fit Carburetor Floats Fuel Strainers For Marvel-Schebler carburetors A M91 Float for Marvel-Schebler small bowl carburetors. Tractors: TO20, TO30, TO35, MF35, F40, MH50, MF135, MF150. Float for Marvel-Schebler large bowl carburetors. Tractors: MF65, MF150, MF165, MF175. Industrials: 3165 using carburetor models: TS695, TS884, TS893, TS947SL. Float Valve Assemblies M91 For Continental Gas Or Standard Motors Diesel Engines Strainer assembly. Tractors: TO35, MF35, F40, MH50, MF50, MF65, MF85, MF88. Industrials: 35, 202 (prior to s/n ), 204 (prior to s/n ), 302 (prior to s/n ), 304 (prior to s/n ), 356 (prior to s/n ). Parts for M91: SFV1 Shut-off fuel valve M1 Gasket, bowl to body, 2" O.D M1 Glass bowl. 2" O.D., 1.280" long 15479AV 14876AV Float valve needle & seat. For Marvel-Schebler carburetors. Tractors: 11 Pony, 16 Pacer, 20, 21, 22, 23, MH30, TE20, TO20, TO30, TO35, MF35, F40, MH50, MF50, MF135, MF150. Industrials: 202, 204, 2135, 2200, Float valve needle & seat. For Marvel-Schebler carburetors. Tractors: 33, 33K, 333, MF65, MF85, MF88, MF90, MF Super 90, MF165, MF175, MF180. Industrials: 302, 303, 304, 356. Carburetor Inlet, Elbow & Strainer 2N M M M M G Bail assembly. Strainer assembly. Tractors: MF135, MF150 (Continental gas only), MF165, MF175, MF180. Industrials: 20, 30, 50, 202 & 204 (late model), 302 (s/n & up), 304 (s/n & up), 356 (late model), 2135, Parts for M91: Glass bowl. 2-1/8" O.D., 2.370" long. Screen, fuel strainer. Gasket, bowl to body, 2-1/8" O.D. Bail & screw assembly M1 Sediment bowl assembly. Includes horizontal inlet and outlet with 1/8" x 1/8" female pipe threads. Tractors: Massey Harris: Pony (to s/n PGA3116). Vintage Iron M91 Elbow & strainer assembly. Tractors: TE20, TO20, TO30, TO35, MF35, MF50. MF-2-75

97 2 ENGINE SYSTEMS Fuel Tank Valve Fuel Gauge For Instrument Panel M M91 Fuel shut-off valve. Tractors: MF50, MF65. Shovel Loader: 356. Fuel shut-off & strainer. Tractors: MF231, MF240 & MF250 (without reserve tank). Industrials: 20D (early models), 30E, 40E. Replaces M M M91 Gauge, fuel. For instrument panel. Tractors: MF231, MF240, MF250, MF253, MF270, MF282, MF283 (except Brazil), MF290, MF298, MF2775 (prior to s/n 9R0726), MF2805 (prior to s/n 9R0726). Industrials: 20D, 30E, 40E, 50E, 50F. Fuel Tank Cap Cap, fuel tank. All gas models M91 FTW M M2 Fuel shut-off & strainer. Tractors: MF270 (early models), MF290 (early models), MF298 (early models). Industrials: 50E, 50F. Forklifts: 6500H, 6800H. Replaces M1. Fuel Tank Webbing Fuel tank webbing. (Sold 3 foot lengths). Black woven nylon type material,.042" thick. Tractors: Fits Allis Chalmers, Avery, Case, Cockshutt, Ford, IH/Farmall, John Deere, Massey Harris, Minneapolis Moline and Oliver models. Vintage Iron Fuel Tank Sending Units Sending unit, for fuel tank. Tractors: MF240, MF250, MF253. Industrials: 20D, 30E, 40E. Sending unit, for fuel tank. Tractors: MF270, MF282, MF283 (except Brazil), MF290, MF298. Industrials: 50E, 50F. Replaces M D 12648G M M91 Auxiliary fuel cap, includes gasket. 1-¾" ID,.350" height. Tractors: Massey Harris: 20, 22, 30, 33, 44, 55, 81, 82, 101 Jr, 101 Sr, 102 Jr, 102 Sr, 333, 444. Vintage Iron Cap. Can be used for auxiliary gas tank cap, power steering reservoir cap, oil filler cap and engine oil cap. Tractors: Massey Harris: Pony (engine oil cap). Vintage Iron Fuel cap. Vented and includes cork gasket. 2-½" ID, ¼" high, 2-5/8" OD. Tractors: Massey Ferguson: TE20 (not threaded), TO20, TO30, TO35, MF35, MF40, MF50, MF65, MF85, MF88, Super 90, MF135, MF150, MF165, MF175, MF1080, MF1100, MF1130, MF1150, MF1500, MF1800. Massey Harris: 50, Pony, Pacer. Vintage Iron Fuel cap with gasket. Vented, 2-11/16" ID, 5/8" height. Top of cap reads "Buy Clean Fuel, Keep it Clean". Tractors: Massey Harris: Colt, Challenger, Mustang, 20, 22, 23, 30, 33, 44, 44-6, 44 Special, 81, 82, 101 Jr., 102 Jr, 101 Sr, 102 Sr. Vintage Iron MF-2-76

98 2 ENGINE SYSTEMS Replacement parts to fit M M M M91 Fuel Lift Pumps Fuel pump for A3-152 & AD3-152 diesel engines, two-hole mounting. Tractors: MF35, MF50, MF135 (prior to s/n 152UA46497D), MF150 (prior to s/n 152UA46497D). Industrials: 203 & 205 (prior to s/n 152UA46497D), 2135 (prior to s/n 152UA46497D). Replaces: 35273, , M91, & M91. Fuel pump for AD3-152 diesel engine, two-hole mounting. Tractors: MF135 (s/n 152UA46497D & up), MF150 (s/n 152UA46497D & up), MF154-4, MF230 (prior to s/n U635849G), MF235, MF240 (prior to s/n U635849G), MF245 (prior to s/n U635849G). Industrials: 20, 20C (prior to s/n U635849G), 30B (prior to s/n U635849G), 40, 203 & 205 (s/n 152UA46497D & up), 2135 (s/n 152UA46497D & up). Replaces & M9. Fuel pump for AD3-152 diesel engine, four-hole mounting. Tractors: MF154-4S, MF230 (s/n U635849G & up), MF231, MF240 (s/n U635849G & up), MF245, MF250, MF253, MF Industrials: 20C (s/n U635849G & up), 20D, 30B (s/n U635849G & up), 30D, 30E, 40E. Replaces , , & M91. Fuel pump for AD4-203 & A4-318 diesel engines, two-hole mounting. Tractors: MF165 (s/n 29F4249 & up), MF255, MF285, MF298, MF698, MF1080, MF1085. Industrials: 30, 40B, 50, 50A, 302 & 304 (s/n 29F4249 & up), 3165 (s/n 29F4249 & up). Combine: 540. Replaces , , , M91, M91, M M M M M M M91 Fuel pump for AD4-203 diesel engine, two-hole mounting, glass bowl. Tractors: MF65, MF165 (prior to s/n 29F4249). Industrials: 302 & 304 (prior to s/n 29F4249), 3165 (prior to s/n 29F4249). Combines: 300. Replaces 32589, , M91, M91. Fuel pump for AD4-236 diesel engines, two-hole mounting. Tractors: MF175 (prior to s/n 236UA57083), MF180 (prior to s/n 236UA57265). Industrials: 31 (prior to s/n 236AU57265). Replaces , , M91, M91. Fuel pump for A4-236 & A4-248 diesel engines, four-hole mounting. Tractors: MF175 (s/n 236UA57083 & up), MF180 (s/n 236UA57265 & up), MF184-4, MF255, MF265, MF270 (early models), MF274-4 (prior to s/n 221N00936), MF275, MF294-4 (prior to s/n ), MF670, MF690. Industrials: 31 (s/n 236UA57083 & up), 50E. Replaces , M91. Fuel pump for AD4-236 & AD4-248 diesel engines, four-hole mounting. Tractors: MF270 (late model), MF274-4 (s/n 221N00936 & up), MF283, MF294-4 (s/n & up), MF375, MF383, MF390, MF390T, MF398, MF3050, MF3060, MF3070. Industrials: 50D. Replaces , , M91. Fuel pump for A6-372 & AT6-354 diesel engines, two-hole mounting. Tractors: MF1105, MF1135. Combines: 750 (prior to s/n ), 760 (prior to s/n ). Replaces , M91. Fuel pump, for A4-300, A6-354, AT6-354 diesel engines, two-hole mounting. Tractors: MF super 90 (s/n & up), MF1100, MF1130. Combine: 410. Replaces: 2641A061, , M91. MF-2-77

99 2 ENGINE SYSTEMS M M91 Fuel pump assembly, Diesel engines, 4 hole mounting. Tractors: MF175, MF180, MF265, MF362, MF396, MF399 (w/a engine, engine), MF699, MF2640, MF2675, MF2705, MF2745, MF3090, MF3095, MF3120, MF3125, MF3140, MF3505, MF3525, MF3545, MF3630, MF3645, MF3650, MF3655, MF3660, MF4245, MF4255, MF4260, MF4263, MF4265, MF4270, MF4360, MF4370, MF4800, MF4900, MF6100, MF6120, MF6150, MF6170, MF6180, MF6190, MF6270, MF6280, MF6290, MF8100, MF8210, MF8220. Combines: 550, 750, 760, 850, 855, 860, 865. Industrials: 6500 Forklift. Stationary engines: A4-236, A , T , , T, TW. Fuel pump for AV8-510 & AV8-540 diesel engines, two-hole mounting. Tractors: MF1150, MF1155. Combines: 760 (s/n & up), 850 (prior to s/n ). Replaces: , , , , M91, M91, M91, M M M M M91 Fuel Injector Pumps To assure proper fit the Mfg #s number on the old part must match the Mfg #s on the new replacement part Fuel injection pump (NEW). AD4.236 engine. Tractors: MF175, MF180, MF255, MF265, MF270, MF275, MF6070. Industrials: MF6500, MF31, MF50C, MF50D. Replaces M1. Reference number CAV3241F360. Fuel injection pump (NEW). AD3.152 engine. Tractors: MF135, MF135UK, MF150, MF235, MF245. Industrials: MF20, MF40, MF200, MF200B, MF2135, MF2200, MF2500, MF4500. Replaces M1, Reference numbers CAV3230F240, CAV3230F180, CAV3230F190, CAV3230F350. Fuel injection pump (NEW). Tractors: MF285, MF298, MF698, MF1080, MF1085. Replaces M1, M1, M1, M1, M1. Reference numbers CAV3342F410, CAV3342F411, CAV3249F240, CAV3343F010. Fuel injection pump (NEW). A3.152 non-advance engines. Tractors: MF35, MF50, MH50. Industrials: MF203, MF205. Reference number CAV3230F M1 Fuel injection pump (NEW). A6.354 engine. Tractors: MF1100, MF1105. Reference numbers CAV3263F670, CAV3362F080, CAV3262F M1 Fuel injection pump (NEW). AT4.236 engine. Tractors: MF390T, MF393, MF398, MF3065, MF3070. Reference numbers CAV3348F230, CAV3348F F938 Fuel Injection Pump. Tractors: MF165, MF255. Industrials: 40, 50. Replaces M91. Reference number CAV3240F938. MF-2-78

100 2 ENGINE SYSTEMS Fuel Injector Nozzle Tips Replacement parts to fit When ordering nozzles for rebuilding, check C.A.V. or Bosch part number stamped on tip body for positive identification. Application Nozzle Tractor: MF35, MF50; Utility: 35, Tractor Shovel: 356; M1 A3-152, A4-203 engines. Tractors: MF50, MF65 Industrial Tractors: 35, 203, 205, M91 Tractors: MF150, MF165 Combines: 300 Industrial Tractors: M91 20, 30, 40B, 50, 203, 205, 302, 304, 356, 2135, 3165 Tractors: MF175, MF180, MF265 Industrial Tractors: MF175, M91 MF180, MF265 Tractors: MF1100 MF1105, MF1135, MF1130 Combines: M M M M M M M M91 Fuel Injectors Fuel injector. Tractors: MF255. Replaces OEM E91 and R91. Fuel injector. Tractors: MF175 UK, MF178 UK, MF194-4F, MF265S, MF275, MF282, MF285S, MF Industrials: 50E, 50H. Replaces OEM E91 and R91. Fuel injector. Tractors: MF165 UK, MF174-4S, MF175, MF178, MF180, MF184-4, MF265, MF265S, MF270, MF274-4, MF275 UK, MF285S, MF294-4, MF365, MF374S, MF374V, MF384S, MF670. Industrials: 31, 50C, 50D, 50E, 50F, 50H. Replaces OEM M91 and E91. Fuel injector. Tractors: MF20, MF30, MF65, MF135, MF135 UK, MF150, MF165, MF230, MF235, MF255, MF300. Industrials: 40, 40B, 50, 50A, 302, 304, 2135, Replaces OEM M1, M91, M91. Fuel injector. Tractors: MF20, MF135, MF135 UK, MF150, MF165, MF165 UK, MF200, MF300. Industrials: 40, 302, 304, 2135, 2200, Fuel injector. Tractors: MF80, MF510, MF1100, MF1130. Replaces OEM E M M M M M1 Bosch No. N/A DLL 150S 316 N/A DLL 150S 324 DLL 150S 469 CAV No. BDLL 110S6133 BDLL 150S 6554 BDLL 150S 6372 BDLL 150S 6382 BDLL 150S 6472 Fuel injector. Tractors: MF1105, MF1135. Fuel injector. Tractors: MF283, MF283 UK, MF290, MF290 UK, MF383, MF390, MF394S, MF690, MF3050, MF3060. Loader Backhoe: 50H. Replaces OEM E91, R91 and Fuel injector. Tractors: MF230, MF231, MF240, MF250, MF255, MF275. Industrials: 20D, 20F, 30E, 40B. Replaces OEM E91 and R91. Transparent Fuel Pump & Filter Bowls Glass fuel bowl, for diesel fuel lift pump. 2-1/16 dia. Tractors: MF35, MF50, MF65, MF Super 90, MF135, MF150, MF165, MF1100, MF1130. Industrials: 203, 205, 2135, Combines: 300, 410. Glass bowl, used with filter elements M91, M1, CAV7111/296. Glass bowl, used with filter elements M1, M91, CAV7111/429. MF-2-79

101 2 ENGINE SYSTEMS Pre-Cleaner Bowls Diesel Fuel Filters M M M Bowl, pre-cleaner. Tractors: MF245, MF275. Can replace Donaldson #PO Vintage Iron A) Bowl O.D. at top 7-1/4" B) Cone I.D. at top 3-1/2" C) Bowl side height 3" D) Overall height 4-1/8" Bowl, pre-cleaner. Tractors: MF1100, MF1105, MF1130, MF1135, MF1150, MF1155. Can replace Donaldson bowl # PO Vintage Iron A) Bowl O.D. at top 10-1/2" B) Cone I.D. at top 5-9/16" C) Bowl side height 3" D) Overall height 4" Clear plastic pre-cleaner bowl. 5.5" top OD, 5" bottom OD. Tractors: MF30, MF31, MF35, MF65, MF85, MF88, MF97 (to s/n ), MF98, MF150, MF165, MF175, MF180, MF200, MF375, MF383, MF390, MF393, MF398, MF399, MF699, MF1080, MF1085, MF3050, MF3060, MF3070, MF3080, MF3090, MF3120, MF3165, Super 90. Vintage Iron Pre cleaner cover. Includes brass nut. 7" diameter. Tractors: MF35 (diesel), 65 (diesel), MF85, MF88, MF90, MF98, MF135, MF150, MF165, MF175, MF180, MF245, MF275, MF282, MF375, MF383, MF390, MF393, MF398, MF399, MF1080, MF1085, MF3050, MF3060, MF3070, MF3080, MF3090. Vintage Iron M M1 CAV7111/796 CAV7111/ M1 Fuel filter element, cartridge type. Used in filter assembly M91 (Purolator). Tractors: MF65 (primary & secondary), 35 Utility (primary). Fuel filter element, external body type. 4-3/8" high. Tractors: MF230, MF235, MF245, MF255, MF265, MF270, MF275, MF282, MF283UK, MF283 Brazil, MF290, MF360, MF375, MF383, MF390, MF390T, MF398, MF670, MF690, MF2745, MF2775, MF2805, MF3050, MF3060, MF3070, MF3505, MF3525, MF3545, MF3630, MF3680, MF3690. Industrials: 20C, 30B, 30D, 30H, 40B, 50C, 50D, 50E, 50F, 50H, 50H, 60H. Forklifts: 4500, Can replace Perkins , M91. Fuel Filter, Can type, 4-3/8" tall diesel fuel filter used with the cav fuel filter system. Tractors: MF145, MF200B, MF200C, MF200D, MF245, MF251E, MF255, MF261, MF265, MF270, MF275, MF275DT, MF275ST, MF282, MF283, MF290, MF292, MF294, MF294-4, MF355, MF365, MF375, MF383, MF390, MF390T, MF398, MF415, MF415N, MF435, MF560, MF575, MF590, MF670, MF675, MF690, MF698T, MF1100, MF1114, MF2620, MF2640, MF2645, MF2680, MF2685, MF2720, MG2725, MF2745, MF2775, MF2805, MF3330M, MF3340, MF3050, MF3060, MF3670, MF3680, MF3690, MF8140, MF8150, MF8160, MF8170, MF8180, MF8240, MF8245, MF8250, MF8260, MF8270, MF8280. Industrials: 20C, 30B, 3. Original C.A.V. fuel filter element, external body type. Can replace M91, M1, M1. Fuel filter, 2.717" tall. Tractors: MF1010, MF1020, MF M91 Fuel filter element, external body type 2-3/4 high. All MF tractors & combines using filter assembly M91, M91, M91, & M91. Will work wherever CAV7111/296 filter is applicable. Replaces M92 (Tri-Pak is replaced by single element) M91, M1. MF-2-80

102 2 ENGINE SYSTEMS Replacement parts to fit CAV7176/ M M1 Original C.A.V. fuel filter element, external body type. Can replace M91, M1, M1, Perkins # & CAV7111/096, CAV7111/296 in all MF applications using filter assembly M91, M91, M91 & M91. Spin-on fuel filter with drain. For diesel engines. Tractors: MF3120T, MF3140 (s/n U514769U & up), MF3660 (s/n U51477U & up). Replaces CAV7176/496A. Fuel water separator cartridge (PRIMARY). Tractors: MF396, MF5465, MF6235, MF6235HV, MF6245, MF6245HV, MF6255, MF6255HV, MF6260, MF6265, MF6270, MF6280, MF6290, MF6465, MF6475, MF6480, MF6497, MF6499, MF7465, MF7475, MF7480, MF8210, MF8220, MF8240, MF8240TRA, MF8250TRA, MF8260, MF8260TRA, MF8270, MF8270TRA, MF8280, MF8280TRA. Air Cleaner Elements M M1 Air filter element, outer, radial seal. Tractors: 4225, 4225A (w/perkins engine); 4233, 4235 (w/perkins engine); 4345, 4355 (w/perkins TW engine); 5425, 5435, 5435HV (w/perkins 1104C-44 engine); MF275, MF275DT, MF275ST (w/perkins P4000 (4.1L) engine); MF4243, MF4245, MF4253, MF4255 (w/perkins TW); MF4325 (w/perkins engine); MF4335 (w/perkins engine); MF435, MF5285 (w/perkins engine); MF6235, MF6245, MF6255 (w/perkins T engine). Air filter element, inner, radial seal. Tractors: 4225, 4225A (s/perkins engine); 4233, 4235 (w/perkins engine); 4345, 4355 (w/perkins TW series engine); 5425, 5435 (w/perkins 1104C-44 engine); MF275, MF275DT, MF275ST (w/perkins P4000 (4.1L) engine); MF4243, MF4245, MF4253, MF4255 (w/perkins TW engine); MF4325 (w/perkins engine); MF4335 (w/perkins engine); MF435, MF5285 (w/perkins engine); MF6235 (w/perkins T engine); MF6245, MF6255 (w/perkins T engine) M M M M M91 Air cleaner element, horizontal, single or outer dual, gas & diesel engines. Tractors: MF135. Industrials: 20, Air cleaner element, vertical, single or outer dual, gas & diesel engines. Tractor: MF135. Industrial: Air cleaner element, single or dual outer. Tractors: MF150, MF165, MF175, MF180. Industrials: 30, 50 (gas only), 50A. Replaces M91, M1. Air cleaner element, for single element filter. Tractors: MF1100, MF1130 (prior to s/n ). Air cleaner element, outer, for dual element filter. Tractors: MF235 Orchard, MF245 Orchard, MF255, MF M M1 Air filter, outer, radial seal. Tractors: 4260A, 4270A (w/perkins 1006 engine); 4270 (w/perkins engine); 4345, 4355 (w/perkins TW engine); 5425 (w/perkins 1104C-44 engine); 5445, 5455 (w/perkins 1104C-44T engine); 6265 (w/perkins TW engine); 6445, 6455 (w/perkins 1104C engine); MF4243, MF4245, MF4253, MF4255 (w/perkins TW engine); MF4263, MF4325 (w/perkins engine); MF4335 (w/perkins engine); MF4360, MF4370 (w/perkins engine); MF5340, MF5355 (w/perkins engine); MF6235, MF6245, MF6255 (w/perkins T engine); MF6260 (w/perkins NA engine). Air filter element, inner, felt media radial seal. Tractors: 4270 (w/perkins engine); 4345, 4355 (w/perkins TW engine); 5425 (w/perkins 1104C-44 engine); 5445, 5455 (w/perkins 1104C-44T engine); 6265 (w/perkins TW engine); 6445, 6455 (w/perkins 1104C engine); MF4243, MF4245, MF4253, MF4255 (w/perkins TW engine); MF4263, MF4325 (w/perkins engine); MF4335 (w/perkins engine); MF4360, MF4370 (w/perkins engine); MF5340, MF5355 (w/perkins engine); MF6235, MF 6245, MF6255 (w/perkins T engine); MF6260 (w/perkins NA engine). MF-2-81

103 2 ENGINE SYSTEMS OBAC422 Oil bath air cleaner filter element. Fits most oil bath air cleaners to replace mesh in the existing air cleaner. Tractors: Avery, Case, Cockshutt, Ford, IH/Farmall, John Deere, Massey Ferguson, Massey Harris, Oliver, Minneapolis Moline. Vintage Iron Engine Oil Filters 15790A Air cleaner clamp. Fits Donaldson air cleaner. Tractors: Massey Ferguson: All gas TE20, TO20, TO30, TO35, MF35, 202, 204. Massey Harris: 20, 81, 82, 101 Jr, 102 Jr. Vintage Iron Air Cleaner Oil Cup Cartridge Type 15791A M M M91 T7030 Air cleaner oil cup. 4-¾" OD at lip, 3" Height, 4.450" ID. Tractors: Massey Ferguson: TO20 gas, TO30 gas, TO35 gas, MF35 gas, 202 gas, 204 gas. Massey Harris: 20, 81, 82, 101 Jr, 102 Jr. Vintage Iron Air Cleaner Hose Hose, air cleaner tube to carburetor. Tractors: TE20, TO20, TO30, MF35, MH50, MF50, MF135, MF150 (except Perkins) " O.D., 1.500" I.D., 2.350" long. Hose, air cleaner to manifold. For dry type air cleaner. Tractors: MF240, MF250. Industrials: 20D, 30E. Air Cleaner Caps Air cleaner cap. Fits outside pipe. 2" ID, 5.25" body diameter. Tractors: Massey Harris: Colt, Mustang, 20, 21, 22, 22K, 30, 30K, 33, 44 Special, 81, 82, 101 Jr, 102 Jr. Vintage Iron Air cleaner cap with flat wire. Fits inside pipe. 4-1/8" body diameter, 1-7/8" OD. Tractors: Massey Harris: Colt, Mustang, 20, 21, 22K, 30, 30K, 33, 44 Special, 81, 82, 101 Jr, 102 Jr. Vintage Iron M M M M M M M1 Tri-pac of oil filter elements, 3 cartridge type. Tractors: TE20, TO20. Oil filter element. Tractors: TE20, TO20. Tri-pac of oil filter elements, 3 cartridge type. For early gas engines. Tractors: 11 Pony, 16 Pacer, 20, 22, 23, 30, 33, 333; TO30, TO35, MF35, F40, MF50, MF65 (repl. orig. Fram C3 element), MF85, MF88, Super 90, MF135, MF150, MF165, 35, 65 (turf & utility). Industrials: 203, 205, 302, 304, 2135, 3165, 356 shovel. Oil filter element. Tractors: 11 Pony, 16 Pacer, 20, 22, 23, 30, 33, 333, TO30, TO35, MF35, F40, MF50, MF65 (replaces original Fram element), MF85, MF88, Super 90, MF135, MF150, MF165, 35, 65 (turf & utility). Industrials: 203, 205, 302, 304, 2135, 3165, 356 Shovel. Oil filter element, cartridge type. For diesel engines. Tractors: FE35, MF35, MF50, MF65, MF135, MF150, MF165, 35, 65 utility. Industrials: 203, 205, 302, 304, 2135, 3165 Utility. Replaces M1, M91, M91 Tri-pack of oil filter elements 3 cartridge type M91. For diesel engines. Tractors: FE35, MF35, MF50, MF65, MF135, MF150, MF165, 35 Utility, 65 Utility. Industrials: 203, 205, 302, 304, 2135, 3165 Utility. Spin-On Type Oil filter spin-on element, 10-11/16" long. Tractors: MF135, MF150, MF165, MF235. Industrials: 203, 204. Others with A3-152, AG3-152, AD3-152, A4-203, AD Replaces Perkins M1 Oil filter spin-on element, 5-3/8" long. Tractors: MF165 gas, MF175, MF180, MF255, MF265, MF275, MF285, MF1080, MF1085, others using A4-212, AG4-212, A4-236, A4-248, A Replaces Perkins MF-2-82

104 2 ENGINE SYSTEMS Replacement parts to fit M M M91 Oil filter spin-on element, 7-1/8" long. Tractors: MF1100, MF1105, MF1130, MF1135, MF2775, MF2805. Combines: 740, 750, 760. Others using A4-300, A6-305, A6-354, AT Replaces Perkins Oil Pressure Switches Oil pressure switch, uses blade type wire terminal. For Perkins diesel engines. Tractors: MF135, MF150, MF165, MF175, MF180, MF230, MF235, MF245, MF255, MF265, MF275, MF285 (s/n 9A & up), MF1080, MF1085, MF1100, MF1105, MF1130, MF1135, MF1150, MF1155, MF1505, MF1805. Industrials: 20, 20C, 30, 30B, 30D, 31, 40, 40B, 50, 50A, 50C, 50D, 203, 205, 302, 304, 2135, Oil pressure switch. Tractors: MF154S, MF174S, MF184-4, MF194F, MF231, MF240, MF250, MF253, MF270, MF274-4, MF282, MF283 (except Brazil), MF290, MF294-4, MF298, MF360, MF362, MF364S, MF375, MF383, MF390, MF393, MF394S, MF398, MF399, MF670, MF690, MF698, MF699, MF2640, MF3050 (to s/n V173002), MF 3060 (to s/n V173002), MF 3070 (to s/n V173002), MF 3090 (to s/n V173002), MF3505, MF3525, MF3545, MF3630, MF3650. Industrials: 20D, 30E, 40E, 50E. Replaces M91, M M M M M M M91 Oil Pressure Gauge, Cap & Dipstick Gauge, 80 lb. oil pressure. Tractors: MH44, 55 series, TE20, TO20, TO30, TO35, MF35, MF50, MF65. For 2" hole. Gauge, oil pressure, for instrument panel. Tractors: TO35 with Standard Motors diesel. Replaces M93. Engine oil level dipstick, all models using Perkins A3-152, AD3-152, A4-203 & AD4-203 engines. Engine oil level dipstick. For Continental gas engines. Tractors: TE20, TO20, TO30, TO35, MF35, F40, MH50, MF50, MF135, MF150. Industrials: 202, 204, Oil filler cap. All TE, TO models; All MF gas models using clip type. Governor Assembly Governor assembly. For Continental engines. Tractors: TO30, TO35, MF35, F40, MH50, MF50, MF135, MF150, 11 Pony. Industrials: 202, 204, 2135, 2200, Also services as a unit tractors: MF135, MF150 with Perkins gas. Supersedes & replaces M91. MF-2-83

105 2 ENGINE SYSTEMS Tachometers Water Temperature Gauge M M91 Tachometer, original style with Ferguson logo. Tractors: TO35, MH50 w/continental gas engines (to s/n ). Vintage Iron Tachometer, Ferguson logo, with mounting brackets. Tractors: TO20, TO30 (equipped with generator). Vintage Iron Tachometer Cables UTG M92 Temperature Gauge, heat indicator for 2" mounting hole. Complete assembly with bracket & adapter for block. Dial calibrated to 250, extra long 72" capillary line. Gauge, water temperature. For instrument panel. Tractors: MF231, MF240, MF250, MF253, MF270, MF282, MF283 (except Brazil), MF290, MF298, MF2775 (to s/n 9R2805), MF2805 (to s/n 9R2805). Industrials: 20D, 30E, 40E, 50E, 50F. Water Temperature Sending Unit M M M91 Tachometer cable assembly, 39". Tractors: TO35 gas (s/n & up), MF35 gas, MH50 gas, MF50 gas, MF135 Continental gas, MF150 Continental gas, MF165 gas, MF175. Industrials: 30 gas, 35 gas (utility & turf), 202, 204, 2135 gas, 3165 Continental gas. Tachometer cable assembly, 27". Tractors: MF35 diesel (to s/n ), MF50 diesel, MF150, MF165 diesel, MF235 diesel orchard, MF245 diesel orchard. Industrials: 30, 31, 203, (to s/n ), 205 (to s/n ). Tachometer cable assembly, 23". Tractors: MF135 Perkins gas & diesel, MF230 diesel (to s/n 9A349238), MF245 diesel except orchard, MF255 with A4-203 diesel. Industrials: 20, 20C diesel (turf, to s/n 9A349236), 40B, M92 Sending unit, water temperature. Tractors: MF25, MF130, MF154-4, MF154-S, MF184-4, MF194F, MF231, MF240, MF250, MF253, MF254-4, MF270, MF274-4, MF282, MF283 (except Brazil), MF285 (to s/n 9A34239), MF290, MF294-4, MF298, MF360, MF362, MF364S, MF375, MF383, MF390, MF393, MF394S, MF398, MF399, MF670, MF690, MF698, MF699, MF2640, MF2675, MF2705, MF2745, MF2775, MF2805, MF3050, MF3060, MF3070, MF3090, MF3505, MF3525, MF3545, MF3630, MF3650, MF3660. Industrials: 20D, 30E, 40E, 50E. Replaces M2, M M91 Tachomoter cable assembly, 53". Tractors: MF85 diesel, MF88 diesel, MF255 early production with A4-236 diesel, MF265 diesel (to s/n 9A349238), MF275, MF285 (to s/n 9A349238). Industrials: 50C, 320 Skidder M91 Tachometer cable assembly, 54". Tractors: MF270, MF282, MF290L. Industrial: 50E. MF-2-84

106 2 ENGINE SYSTEMS Replacement parts to fit M M M M M M M M91 Water Pumps Pump less pulley. Tractors: 33, 44, 444, 55, 555. Pump with cast iron body, less pulley. Tractors: TE20, TO20, TO30. Pump less pulley, for Continental Gas engines. 2-3/4" impeller. Tractors: TO35, MF35, F40, MH50, MF50, MF135, MF150. Industrials: 35, 202, 204. Pump with pulley for AD3-152 diesel. Tractors: MF35, MF50. Industrials: 35, 203, 205. Uses repair kit M91. Pump with pulley, for AD3-152 diesel. Tractors: MF135, MF150, MF230, MF235, MF245. Industrials: 20, 20C, 30B, 2135, 2500 forklift. For AG3-152 gas in tractors: MF135 exc. orch., MF150. Industrials: 20 (s/n 152UA18330A & up), 203, 205, 2500 forklift. Replaces M91. Uses repair kit M91. Pump less pulley, for Continental Gas engines. 3" impeller. Tractors: MF65, MF180. Industrials: 302, 304. Pump with pulley, for AD4-203 diesel. Tractors: MF65, MF165, MF255. Industrials: 30, 50, 302, 304. Replaces U5MW0061, M91, M91. Pump less pulley, for A4-236 diesel & A4-248 diesel. Tractors: MF175, MF180, MF255, MF265, MF270, MF275 (less plug), MF374, MF384 Industrial: 50H. Replaces , M91, M M M M M M M M91 Water pump, complete. Tractors: MF399, MF3095, MF3120, MF3125, MF3140, MF3645, MF3655, MF3660, MF6170, MF6180, MF6190, MF8120. Replaces M91, M91, M91, 4131E011, 4131E015, U5MW0092, U5MW0140. Pump, less pulley & back housing. For diesel engines A4-236, AT4-236, A Tractors: MF375, MF383, MF390, MF390T, MF393, MF398, MF3050, MF3060, MF3070. Replaces , , , M91, M91, M91, M91. Pump less pulley & back housing. 3-3/4" impeller. Tractors: MF85, MF88. Pump less pulley, for A4-318 diesel. Tractors: MF285, MF298. Industrials: 70 backhoe loader, 320 skidder. Combine: 540. Includes mounting gaskets. Replaces Perkins U5MW0009. Pump less pulley, for dual thermostats. For diesel engines A6-354, AT Tractors: MF1100, MF1105, MF1130, MF1135. Replaces , , , , , M91, M91, M91, M91, M91. Pump less pulley, for diesel engines A6-372, A6-3724, A Combines: 550, 750 (s/n & up), 850 (to s/n ). Replaces Perkins , , ; MF M91, M91, M91. Uses repair kit M91. Pump less pulley, for diesel engines A6-354, A6-3544, AT6-354, AT Tractors: MF399 (with belt drive), MF699, MF2640, MF2675, MF3090, MF3505, MF3545, MF3630, MF3650. Replaces Use repair kit M91. MF-2-85

107 2 ENGINE SYSTEMS M M M M91 10R M M M M1 Water pump assembly. Perkins Phaser (GREEN) engines. (Perkins engines , 60T, , 40T, 42, ). Tractors: MF4225, MF4235, MF4245, MF4255, MF4265, MF4325, MF4335, MF4345, MF4355, MF4365, MF6235, MF6245, MF6255, MF6260, MF6265, MF6270, MF6280, MF6290, MF8210, MF8220, MF8925, MF8925T, MF8926, MF8926T, MF8937, MF8937T, MF8939, MF8939T. Replaces Perkins number U5MW0190, U5MW0192. Water Pump Repair Kits See water pump listing for engine and model application. Repair kit, services pumps M91 & M91. Repair kit, services pump M91 & M91. Repair kit, services water pump M91. Replaces U7LW0020. Repair kit, MF95, Super 95, MF97. Replaces M91. Cooling Group Gaskets Gasket, water outlet elbow. Tractors: TO35, MF35, & MF50. Gasket, thermostat body. Tractors: TO20, TO30, TO35, MF35, MF50. Gasket, support to water pump body. Tractors: TO20, & TO30. Water Pump Pulley Water pump pulley, is used with M91 water pump for Continental 4-cylinder gas engine Z134. Tractors: TO35, MF35, MF135. Industrials: 202, 204. Belts Application Belts MF M1 MF M1 MF35 (to s/n M1 9A38905) MF M1 MF40B M2 MF50C M2 MF50D M2 MF M1 MF M1 MF M2 MF M91 MF M1 MF M1 MF135 (to s/n M1 9A38905) MF M1 MF150 (with M1 generator) MF M2 MF M1 MF M1 MF M1 MF M1 MF M1 MF M1 MF M1 MF M1 MF M2 MF M1 MF M1 MF M1 MF M1 MF M1 MF M1 MF M2 MF M2 MF B059 MF M2 MF M91 MF M1 Type Fan & Alternator Fan & Alternator Fan Fan & Alternator Fan Fan Fan Fan, Alternator, & Generator Fan Fan Fan & Alternator (w/58-1/8 belt OC) Fan & Alternator (s/n 9A38905 & up) Fan & Alternator (Orchard style; s/n 9A38905 & up) Fan Fan Fan Fan Fan Fan Fan & Alternator Fan Fan Fan Fan & Generator Fan & Generator (s/n 9A40277) Fan Fan & Generator Fan & Generator Fan & Alternator Fan & Alternator Fan & Alternator Fan & Alternator Fan Fan Fan & Alternator (w/ 1/2 belt TW) Fan Fan & Alternator Air Conditioning MF-2-86

108 2 ENGINE SYSTEMS Replacement parts to fit Application MF383 MF383 MF390 MF390 MF398 MF670 MF690 MF698 MF1030 MF1030 MF1045 MF1080 MF1100 MF1100 MF1100 MF1100 MF1105 MF1105 MF1130 MF1130 MF1130 MF1140 MF1150 MF1155 MF1500 MF1505 MF1540 MF1560 MF1800 MF1805 MF2640 MF2640 MF2640 MF2640 Belts M M M M1 2614B M M M M M M M M M M M M M M M M M M M M M M M M M M M M M1 Type Application Fan & Alternator MF2675 Air Conditioning MF2675 Fan & Alternator Air Conditioning MF2675 Fan & Alternator (w/ 1/2 belt TW) MF2675 Fan & Air Conditioning Fan & Air MF2705 Conditioning Air Conditioning MF2745 Fan & Alternator MF2770 (w/42-1/4 belt OC) MF2775 Fan & Alternator MF2800 (w/41-3/4 belt OC) MF2805 Fan & Alternator MF3090 Air Conditioner Fan & Alternator MF3090 Fan & Alternator (w/o A/C; w/57-1/4 belt MF3090 OC) Fan & Alternator MF3505 (w/58-1/8 belt OC) MF3505 Air Conditioning Air Conditioning MF3505 Fan & Alternator (w/58-1/8 belt OC) MF3505 Fan & Alternator (to s/n 9B15389; MF3505 w/single belt) Fan & Alternator MF3525 (w/dual belts) MF3525 Air Conditioning Fan & Alternator MF3525 Air Conditioning (w/47-1/4 belt OC) MF3525 Alternator & Air Conditioning MF3545 Alternator MF3545 Alternator Alternator MF3545 Fan Alternator MF3545 Alternator Fan MF3660 Fan & Alternator (w/60-1/4 belt OC) MF4800 Air Conditioning Alternator (w/39-7/8 MF4800 belt OC) Belts M M M M M M M M M M B M M M M M M M M M M M M M M M M M M1 Type Fan Air Conditioning (w/45-7/8 belt OC) Air Conditioning (w/44-7/8 belt OC) Water Pump & Alternator (s/n 9R414 & up) Air Conditioning (to s/n 9R5659) Fan Fan Fan Fan Fan Fan & Alternator (w/59-1/4 belt OC) Fan & Alternator (w/60-1/4 belt OC) Fan & Air Conditioning Fan & Alternator Fan & Alternator (w/55-3/4 belt OC) Fan & Alternator (w/39-7/8 belt OC) Air Conditioning (w/45-7/8 belt OC) Air Conditioning (w/47-1/4 belt OC) Fan & Alternator Fan & Alternator (w/55-3/4 belt OC) Air Conditioning (w/45-7/8 belt OC) Air Conditioning (w/47-1/4 belt OC) Fan & Alternator Fan & Alternator (w/55-3/4 belt OC) Air Conditioning (w/45-7/8 belt OC) Air Conditioning (w/47-1/4 belt OC) Fan & Air Conditioning Air Conditioning (to s/n 9D004000) Fan & Alternator (to s/n 9D003701) MF-2-87

109 2 ENGINE SYSTEMS Application MF4840 MF4840 MF4880 MF4880 MF4900 MF4900 MF5435 MF5465 MH44 TE20 TEA20 TO20 TO Industrial M M1 Belts M M M M M M M M A M M M M M1 Fan Blades Type Air Conditioning (to s/n 9D004000) Fan & Alternator (to s/n 9D003701) Air Conditioning (to s/n 9D004000) Fan & Alternator (to s/n 9D003701) Air Conditioning (to s/n 9D004000) Fan & Alternator (to s/n 9D003701) Fan & Alternator (non-high Visibility) Air Conditioning Fan (w/continental gas) Fan Fan Fan Fan Fan & Generator Fan blade, front blade for 2-piece fan. Tractors: MF240, MF250, MF253. Industrials: 20D, 30E, 40E. Use with blade M1. Fan blade, rear blade for 2-piece fan. Tractors: MF240. MF250, MF253. Industrials: 20D, 30E, 40E. Use with blade M G M1SR M M93SR Radiator cap for non pressurized systems. Fits on inside of neck " tab to tab, 2.806" ID cap. Tractors: Massey Harris: Pacemaker, Challenger. Vintage Iron Safety Release Radiator Cap 13 psi. For radiator overflow reservoir systems, fits ¾" deep neck. Tractors: MF205, MF210, MF220, MF1010, MF1020, MF1030, MF1035, MF1040, MF8780P. OE Type Radiator Cap 13 psi. For radiator overflow reservoir systems, fits ¾" deep neck. Tractors: MF205, MF210, MF220, MF1010, MF1020, MF1030, MF1035, MF1040, MF8780P. Safety Release Radiator Cap 10 psi. Fits ¾" deep neck. Tractors: MF154-4, MF184-4, MF240, MF251E, MF253, MF254, MF263, MF274, MF281 Special, MF294, MF360, MF362, MF375, MF383, MF390, MF390T, MF393, MF396, MF398, MF399, MF451, MF471, MF481, MF670, MF690, MF698, MF699, MF750SP, MF760SP,, MF850, MF860, MF2210, MF3120T, MF3660, MF4235, MF4243, MF4255, MF4325, MF4345, MF4355, MF5200, MF6170, MF6180, MF6265, MF6280, MF6290, MF8120, MF8160, MF8240, MF8250, MF8450, MF8460. Radiator Cap & Drain Plug M1 Drain cock, fits all: TO & MF models. 1/4" NPT M91 Radiator cap. Tractors: TO20, TO30, TO35, MF50, MF135, MF150, gas or diesel. MF-2-88

110 2 ENGINE SYSTEMS Replacement parts to fit M M M91SR OE Type Radiator Cap 10 psi. Fits ¾" deep neck. Tractors: MF154-4, MF184-4, MF240, MF251E, MF253, MF254, MF263, MF274, MF281 Special, MF294, MF360, MF362, MF375, MF383, MF390, MF390T, MF393, MF396, MF398, MF399, MF451, MF471, MF481, MF670, MF690, MF698, MF699, MF750SP, MF760SP, MF850, MF860, MF2210, MF3120T, MF3660, MF4235, MF4243, MF4255, MF4325, MF4345, MF4355, MF5200, MF6170, MF6180, MF6265, MF6280, MF6290, MF8120, MF8160, MF8240, MF8250, MF8450, MF8460. OE type radiator cap, 7 psi. For "B" size 2-11/16" OD. Fits ¾" deep filler neck. Tractors: MF366, MF2645, MF2685, MF2725, MF3050, MF3060, MF3065, MF3070, MF3080, MF3085, MF3090, MF3095, MF3115, MF3120, MF3125, MF3140, MF3610, MF3630, MF3635, MF3645, MF3650, MF3655. Safety release radiator cap, 7 psi. Fits ¾" deep neck. Tractors: MF35, MF40, MF65, MF90, MF135, MF150, MF165, MF175, MF202 Industrial, MF204 Industrial, MF230, MF235, MF240, MF245, MF250, MF255, MF265, MF270, MF275, MF285, MF290, MF294, MF298, MF540SP, MF550, MF550SP, MF850, MF1085, MF1105, MF1135, MF1155, MF1500, MF1505, MF1800, MF1805, MF231S, MF2640, MF2675, MF2705, MF2745, MF2770, MF2775, MF2805, MF300SP, MF3070, MF3090, MF3120, MF3140, MF3505, MF3525, MF3545, MF3625, MF3630, MF3660, MF3670, MF3680, MF3690, MF4800, MF4840, MF4880, MF4900, MF8560, MF9720, TO20, TO30, TO M M M M M M M91 Radiator Assemblies Radiator assembly with cap, for gas or diesel engines. Tractors: MF135 (except vineyard) with Perkins gas (prior to s/n 9A117590), MF135 vineyard with Perkins diesel (prior to s/n 9A117609). Industrials: 20, Pad, radiator mounting, use with radiator M94. Tractors: MF135. Industrials: 20, Also for radiators on tractors: TO35, MF35, MF230, MF235 exc. orch., MF240, MF245 exc. orch., MF250, MF253; industrials: 20C turf, 20D, 30E, 35, 40E, 202, 203, 204, 205. Radiator assembly, for Z120, Z129, Z134 Continental engines. Tractors: TE20, TEA20, TO20, TO30, TO35, MF35. Industrials: 202, 204 (prior to s/n ). Can replace radiators M1 & M91. Radiator assembly. Tractors: MF240, MF250. Industrials: 20D, 30E, 40E manual steering, 2WD. Radiator assembly. Tractors: MF165UK, MF185, MF188. Core Height: 19-1/8" Core Width: 15-1/8" 3 row, 8 FPI. Radiator assembly. Tractors: MF230 (prior to s/n 9A284347), MF245 gas (prior to s/n 9A ), MF245 diesel (prior to s/n 9A282759, with 4-1/2" neck). Core Height: 18-1/2" Core Width: 15", 3 row, 8 FPI. Radiator assembly. Tractors: MF230 (s/n 9A & up), MF245 Gas (s/n 9A & up, with 3-1/2" neck), MF245 Diesel (s/n 9A & up). Core Height: 18-1/2" Core Width: 15-1/2" 3 row, 9 FPI. MF-2-89

111 2 ENGINE SYSTEMS M94 Radiator, 4-11/16" filler neck. Overall Dimensions: 25-1/8" x 16-1/16" Core Deminsions: 19" x 15-1/4" x 2-1/8" Inlet 1-1/2" Outlet 1-1/2", 3 row Tractors: MF255, MF265 (early Diesel, w/ oil cooler). Upper Radiator Hoses M M2 Radiator, 5-3/16" filler neck. Overall Dimensions: 25-1/8" x 16-1/16" Core Dimensions: 19" x 15-1/4" x 2-1/16" Inlet 1-1/2", Outlet 1-1/2", 3 row Tractors: MF 255 (later Diesel). Radiator Assembly. Tractors: MF375, MF383, MF390, MF390T, MF393, MF398, MF M M1 Hose, radiator upper. For Continental gas engine. Tractors: TO20, TO30, TO35, MF35. Industrials: 202 (prior to s/n ), 204 (prior to s/n ). For Perkins gas or diesel. Tractors: MF35, MF50, MF135, MF230 (prior to s/n 9A243032), MF235 (except orchard). Industrials: 20, 203, 205, " long, 1.50" I.D., 1.82" O.D. Hose, radiator upper. Tractors: TO35 (s/n & up), MF35 gas M M M M91 Radiator assembly. Tractors: MF35 Diesel, MF203, MF205 Diesels. Core Height: 23-1/8" Core Width: 16" 3 row, 9 FPI Radiator assembly (Diesel only). Tractors: MF50, MF50A, MF65, MF302, MF304. Core Height: 22-1/4" Core Width: 16-5/16" Thermostats Thermostat. Fits in upper radiator hose, /4" long for 1-1/2" I.D. hose. Tractors: TO20, TE20, TO30. Thermostat Tractors: TO35, MF35, F40, MF M M M M M M2 Hose, radiator upper. For Z134 or Z145 Continental gas engine. Tractors: MF135, MF230 (prior to s/n 9A243032), MF235. Industrials: Hose, radiator upper. For Perkins diesel engine. Tractors: MF65. Industrials: 50, 50A, 302, 304, 356. Hose, radiator upper. For Perkins diesel engine. Tractors: MF165 except with dual tricycle, MF255. Industrials: 30, Hose, radiator upper. Tractors: MF165 with Perkins gas, MF175 with Perkins gas or diesel, MF255 gas or A4-236 diesel, MF265, MF275. Industrials: 30 gas, 31. Hose, radiator upper. Tractors: MF231, MF240, MF250, MF253. Industrials: 20D, 30E, 40E. Replaces M1. Hose, radiator upper. For diesel engines. Tractors: MF230 (s/n 9A & up), MF245 (except orchard). Industrials: 20C turf. MF-2-90

112 2 ENGINE SYSTEMS Replacement parts to fit Lower Radiator Hoses Other Cooling Hoses M M M M M M M M M M M1 Lower hose. Tractors: TO20, TO " O.D., 1.50" I.D., 13.50" long. Hose, radiator lower. For Continental gas engines. Tractors: TO35, MF35, MF135. Industrials: 202, 204, " O.D., 1.50" I.D., 10.70" long. Hose, radiator lower. For Perkins diesel engines. Tractors: MF35, MF135, MF230, (prior to s/n 9A243032), MF235 (except orchard). Industrials: 20, 35 utility, 203, 205, Hose, radiator lower, water pump inlet. Tractors: MF135 with Perkins gas. Hose, radiator lower. Tractors: MF175 diesel, MF255 with A4-236 diesel, MF265 diesel (except orchard). Hose, radiator lower. Tractors: MF235 orchard diesel, MF245 orchard diesel. Industrials: 20C (except turf), 30B diesel, 30D, 40. Hose, radiator lower. Tractors: MF231, MF240 (except with hydrostatic steering), MF250. Industrials: 20D, 30E. Hose, radiator lower to metal tube. Tractors: MF230 (s/n 9A & up), MF245 (except orchard). Industrials: 20C turf. Hose, radiator lower. For Perkins diesel engine. Tractors: MF65. Industrials: 50, 50A, 302, 304, 356. Hose, radiator lower. For Perkins diesel engine. Tractors: MF165 (except with dual tricycle), MF255. Industrials: 30, Radiator hose, lower. Tractors: F40, MF165, MF50, MF65, MH M M M M M M2 Hose, water pump to block inlet. For Perkins gas or diesel engines. Tractors: MF35, MF50, MF135, MF150, MF154-4, MF230, MF231, MF235, MF240, MF245, MF250, MF Industrials: 20, 20C, 20D, 30B, 30D, 30E, 40, 203, 205, Replaces Hose, by-pass, water pump to thermostat housing. For Perkins gas or diesel engines. Tractors: MF35, MF50, MF135, MF150, MF154-4, MF230, MF231, MF235, MF240, MF245, MF250, MF Industrials: 20, 20C, 20D, 30B, 30D, 30E, 40, 203, 205, Replaces M1. Hose, inlet, water pump to block. For diesel engines. Tractors: MF65, MF165, MF255 with AD Industrials: 30, 40B, 50, 50A, 302, 304, Replaces M91. Hose with clamps, by-pass, water pump to thermostat housing. For Perkins diesel engines. Tractors: MF65, MF165, MF255. Industrials: 30, 40B, 50A, 302, 304. Replaces M1. Hose, pump to inlet connections. Tractors: MF1100 diesel, MF1105, MF1130 diesel, MF1135 diesel. Replaces M1. Heater for Intake Manifold Heater, for intake manifold on Perkins diesel engines. 3/8" thread small end,.865" thread large end. Tractors: MF154-4, MF184-4, MF240, MF250, MF270, MF274-4, MF399, MF670, MF690, MF698, MF3070, MF3090. Replaces Perkins MF-2-91

113 2 ENGINE SYSTEMS Engine Heaters Manifolds M94 GE361 Engine heater, 3/4" pipe thread, 400 watts, 115-volt. Fits most Massey Ferguson diesels. Replaces GE360. Replacement cord: GE360C. Adapter, 3/4" FNPT, 1-1/4" bushing, 32mm O.D. Used with GE M1 Exhaust manifold. For AD3-152 Perkins diesel engines. Tractors: MF231, MF240, MF250. Industrial: 20D with horizontal exhaust. Requires M1 & M1 gaskets. Replaces GE362 Engine heater. 3/4" pipe thread, 400 watts, 115 volt. Fits most Perkins diesels. Contains 1 GE360 & 1 GE A91 Frost plug engine heater, 1-1/4" dia. clamp & o-ring mounting, 600 watts. For Massey Ferguson models. Tractors: MF135, MF150, MF230, MF231, MF235, MF240, MF245, MF250, MF253, MF254-4, MF282, MF283, MF298, MF360, MF364S, MF399 with eng., MF698. Industrials: 20, 20C, 30B, 40. Replacement cord: M1, 12" long M91 Manifold, universal intake & exhaust, includes gasket set. Tractors: TO20, TO30, TO35, MF35, MF135. Replaces M91. Exhaust Elbow G176E601ELB Exhaust elbow. Gas tractors: MF M2 Exhaust elbow. Tractors: MF255, MF265, MF M1 Manifold, intake & exhaust. Tractors: Massey Harris Pony M M1 Exhaust elbow. For Perkins diesel engines in tractors: MF1105, MF1130, MF1135. Exhaust elbow, Vertical diesel. Tractors: MF235, MF245. G176E601 Exhaust manifold, less gasket. For gas engines Tractors: MF Exhaust manifold, for turbocharged engines. Tractors: MF1105, MF1130, MF1135, MF2705, MF3525, MF3545, MF3630, MF3650 (w/ci engines w/13 bolt mounting). MF-2-92

114 2 ENGINE SYSTEMS Replacement parts to fit M1 Manifold Gaskets Gasket, exhaust manifold to pipe or elbow. Tractors: TO35, MF35, MF50, MF135. Industrials: 35 Utility, 203, 205. Custom Vertical Muffler Assemblies & Pipes M M M M M1 Gasket, exhaust manifold to cylinder head. For Perkins diesel engines. Tractors: MF135, MF150, MF154-4, MF154-4S, MF230, MF231, MF235, MF240, MF245, MF250, MF Industrials: 20D, 30E. 2 required. Gasket, exhaust manifold to pipe or elbow. For Perkins diesel engines. Tractors: MF135, MF150, MF154-4, MF154-4S, MF230, MF231, MF235, MF240, MF245, MF250, MF Industrials: 20D, 30E. Replaces M1. Gasket, carburetor to manifold. Tractors: TO20, TO30, TO35, MF35, F40, MF50, MF135, MF150. Industrials: 202, 204, Gasket, manifold. Tractors: TO20, TO30, TO35, MF35, F40, MF50, MF135. Gasket, exhaust manifold to cylinder head. For Perkins diesel engines. Tractors: MF175 (vertical exhaust), MF180, MF270, MF283 (except Brazil), MF290, MF362. Industrials: 31 (horizontal exhaust), 50E. 2 required. M112 M115 M1111 M134 M135 Vertical 2-piece muffler assembly. Flared inlet, 1-1/2" outlet OD, 48" OA length. Tractor: TE20, TO20, TO30. Vertical 2-piece muffler assembly with 3-bolt flange. 1-1/2" outlet OD, 47" OA length. Tractors: TO35. Vertical 2-piece muffler & pipe. 2" inlet ID, 2" outlet OD, 31" OA length. Tractor: MF65. Custom-designed upright muffler & pipe with 3-bolt flange. 1-1/2" outlet OD, 42" OA length. Tractors: MF35 (with Perkins diesel), MF135 (with Continental gas). Vertical one piece muffler & pipe assembly, custom design shown. For Perkins gas or diesel engines. Tractor: MF135. Pipe has 3-bolt flange inlet, muffler outlet 1-3/4" O.D., shell length 12, shell 4-1/2" O.D. Use with gasket M M1 Gasket, exhaust manifold to elbow. For Perkins diesel engines. Tractors: MF175 (vertical exhaust), MF180, MF270, MF283 (except Brazil), MF290, MF362. Industrials: 31 (horizontal exhaust), 50E. 1 required. MF-2-93

115 2 ENGINE SYSTEMS Customized Horizontal Muffler Assemblies Exhaust Weathercaps Improved one-piece design for popular models. M500 M119 M132 M M M5 Muffler & pipe assembly. Tractors: TO20, TO30. Replaces M92 muffler & M1 pipe. Muffler & pipe assembly with 3-bolt flange. Tractors: TO35, MF35 (Continental gas). Replaces M92 muffler & M92 pipe. Uses gasket M1 (not included). Muffler & pipe assembly with 3 bolt flange. Tractor: MF35 (Perkins diesel). Replaces M92 muffler & M91 pipe. Muffler & pipe assembly with 3-bolt flange. Tractor: MF135 (Perkins gas & diesel). Replaces M91 muffler & M91 pipe on late models, also will replace M92 & M91 on early models. Uses gasket M1 (not included). Muffler Assemblies Muffler assembly with 3 hole mounting. Tractors: MF365, MF375, MF383, MF390. Muffler assembly with 4 hole mounting. Tractors: MF390 (to s/n B18008), MF390T, MF393, MF398. Replaces WC0 WC1 WC2 WC3 WC4 WC5 WC6 WC7 WC8 WC9 WC10 WC11 WC12 WC13 WC14 WC15 MIN. EHAUST O.D. 1" 1-1/4" 1-1/2" 1-3/4" 2" 2-1/4" 2-1/2" 2-3/4" 3" 3-1/4" 3-1/2" 3-3/4" 4" 4-1/4" 4-1/2" 5" MA. EHAUST O.D. 1-3/16" 1-7/16" 1-11/16" 1-15/16" 2-3/16" 2-7/16" 2-11/16" 2-15/16" 3-3/16" 3-7/16" 3-11/16" 3-15/16" 4-3/16" 4-7/16" 4-11/16" 5-3/16" Universal Muffler Clamps M1 Muffler assembly with 3 hole mounting. Tractors: MF399. MCK M91 MCK-3 Muffler Clamp Kits Muffler clamp kit. Tractors: TO20, TO30. Kit contains 2 high strength aluminum clamps, nuts, bolts, & lockwashers. Replacement clamp half for MCK-2. Same as MCK-2 with heavy-duty malleable clamps. Replaces MC150 MC158 MC134 MC178 MC200 MC225 MC250 MC275 MC300 MC350 Full 360 saddle clamps with nuts. O.D. designation refers to pipe size. PIPE O.D. 1-1/2" 1-5/8" 1-3/4" 1-7/8" 2" 2-1/4" 2-1/2" 2-3/4" 3" 3-1/2" MF-2-94

116 2 ENGINE SYSTEMS Replacement parts to fit Horizontal Mufflers for Gas & Diesel Tractors Application Muffler TO20, TO30 Continental gas M92 TO35 Continental Gas M92 MF35 Continental gas, M92 Perkins diesel MF35 Perkins diesel M92 MF50, MH50, F40 gas M91 MF50 Perkins diesel M91 MF65 Continental gas M91 MF65 Perkins diesel M91 MF135 Continental gas M92 MF135 Perkins to s/n M92 9A99582 MF135 Perkins s/n 9A M91 & up MF150 Continental gas M92 MF150 Continental gas M92-TP MF150 Perkins gas to s/n M92 9A MF150 Perkins gas to s/n M92-TP 9A MF150 Perkins gas s/n M91 9A & up MF150 Perkins gas s/n M92-TP 9A & up MF150 Perkins diesel M91 MF150 Diesel with generator M92 MF150 Diesel with generator M92-TP MF165, MF175, MF M92 MF165, MF175, MF M92-TP MF240 to s/n 2773N01001, M92 MF245, MF255, MF265, MF275 MF240 to s/n 2773N01001, M92-TP MF245, MF255, MF265, MF275 Tractors: Massey-Harris M91 ( ) (Gas & Diesel), 20, 20K, 22, 22K (Except 1948), 30, 30K, 33, 333, 44, 44SPL, 44D, 44K, 44-6, 444, 81, 82, 101JR, 101SR, 102SR. Inlet I.D. 1-1/2" 1-1/2" 1-1/2" 1-1/2" 1-15/16" 1-3/4" 1-15/16" 1-3/4" 1-1/2" 1-1/2" 1-3/4" 2" 2" 2" 2" 1-3/4" 2" 1-3/4" 2" 2" 2" 2" 2" 2" 2-3/8" Outlet O.D. 1-1/2" 1-1/2" 1-1/2" 1-1/2" 1-3/8" 1-3/4" 1-3/8" Bent 1-1/2" 1-1/2" 1-3/4" 2" 2" 2" 2" 1-3/4" 2" 1-3/4" 2" 2" 2" 2" 2" 2" 2-1/2" Overall Length 34" 34" 34" 34" 18-1/2" 34" 18" 40" 34" 34" 39" 32" 32" 32" 32" 39" 32" 39" 32" 32" 32" 32" 32" 32" 21" Diameter 3-1/4" 3-1/4" 3-1/4" 3-1/4" 3-1/4" 3-1/4" 3-1/4" 3-1/4" 3-1/4" 3-1/4" 4-1/4" 3-1/4" 3-1/4" 3-1/4" 3-1/4" 4-1/4" 3-1/4" 4-1/4" 3-1/4" 3-1/4" 3-1/4" 3-1/4" 3-1/4" 3-1/4" Body Style Round Round Round Round Round Round Round Round Round Round Round Round Round Round Round Round Round Round Round Round Round Round Round Round Round Inlet Clamp MC150 MC150 MC150 MC150 MC200 MC134 MC200 MC134 MC150 MC150 MC134 MC200 MC200 MC200 MC200 MC134 MC134 MC134 MC200 MC200 MC200 MC200 MC200 MC200 Outlet Clamp MC150 MC150 MC150 MC150 MC150 MC134 MC150 MC150 MC150 MC134 MC200 MC200 MC200 MC200 MC134 MC134 MC134 MC200 MC200 MC200 MC200 MC200 MC200 MFLD to MUFF Pipe M M M M M M M M92 MF-2-95

117 2 ENGINE SYSTEMS Vertical Mufflers for Gas & Diesel Tractors Application Muffler TO20, TO30 Continental M112 gas TO35 Continental Gas M115 MF35 Continental gas, M91 Perkins diesel MF50, MH50, F40 gas M91 MF50 Perkins diesel M91 MF65 Continental gas M1111 MF65 Perkins diesel M91 MF85, MF88 Continental M91 gas MF85, MF88 diesel M92 MF135 Continental gas M134 MF135 Perkins gas & diesel M91 MF150 Continental gas M91 MF150 Perkins diesel to s/n M92 9A MF150 Perkins diesel to s/n M92-TP 9A MF150 Perkins diesel s/n M91 9A & up MF150 Diesel with M91 generator MF165, MF175, MF M91 MF165, MF175, MF M95 Economy muffler MF245, MF255, MF265, M92 MF275 MF245, MF255, MF265, M92-TP MF275 MF285, MF1085 oval M91 MF1100 gas and diesel M92 round MF1100 gas and diesel M91 oval MF1130 turbo M91 MF1105, MF M91 Inlet I.D. Flared 3-bolt flange 1-7/8" 1-15/16" 1-3/4" 2" 1-3/4" 2-13/16" 2-1/4" 3-bolt flange 1-7/8" 1-3/4" 2" 2" 1-3/4" 1-3/4" 2-1/8" 2-1/8" 2-1/8" 2-1/8" 2-3/4" 2-3/4" 2-3/4" 3-1/2" 3-7/16" Outlet O.D. Overall Length 1-1/2" 48" 1-1/2" 47" 2" 34" 1-3/8" 18-1/2" 1-3/4" 34" 2" 31" 1-3/4" 34" 2-1/4" 38" 2-1/4" 37" 1-1/2" 42" 2" 34" 1-3/4" 39" 2" 32" 2" 32" 1-3/4" 39" 1-3/4" 39" 2" Bent 40" 2" Bent 40" 2" 37" 2" 37" 2-3/4" 24" 2-3/4" 32" 2-3/4" 32" 3-1/2" 32" 3-1/2" 28" Diameter /4" 3-1/4" 3-1/4" /4" 4-1/4" 4-1/4" /4" 4-1/4" 3-1/4" 3-1/4" 4-1/4" 4-1/4" 5-1/2" 4-1/4" 3-1/4" 3-1/4" 6" x 10" 5-1/2" 5" x 11" 6" x 9-1/2" 6" x 10" Body Style Inlet Clamp Round Round Round -- Round Round Round -- Round Round Round Round Round Round Round Round Oval Oval Oval Round Oval Oval Oval MC200 MC200 MC134 MC134 MC225 MC225 MC178 MC134 MC200 MC200 MC134 MC134 MC225 MC225 MC225 MC225 MC275 MC275 MC275 MC350 MC350 Outlet Clamp MC200 MC150 MC134 MC134 MC225 MC225 MC200 MC134 MC200 MC200 MC134 MC134 Rain Cap WC4 WC3 WC3 WC5 WC5 WC4 WC3 WC4 WC4 WC3 WC3 WC4 WC4 WC7 WC7 WC7 WC10 WC10 MF-2-96

118 3 ELECTRICAL Replacement parts to fit Side Mount Distributor Distributor Repair Parts M91-TP Information For Ordering Distributor Repair Parts NOTE: Original style distributor M91-TP has been supplied by Tisco since February 1987 and replaces Tisco distributor M91-TIS. Visual identification is necessary when ordering replacement parts M91-TP (has external oiler and terminal for coil wire) M91-TIS (no external oiler and has 14" wire attached to housing). Original style side-mount distributor assembly, complete with rotor & cap. Replaces TISCO M91-TIS. Tractors: TO20, TO30, TO35, MF35 (prior to s/n ), F40, MF50 (prior to s/n ). Replaces , , (MF181686M91), , Spark Plug Wiring Set FET12300A MF12106A MF12200A MF12171AA Repair parts for M91-TP original-style distributor supplied by TISCO since February Condenser Cap (A) Rotor (B) Points (C) MF12176 Cam & weight assy. (D) Repair parts for M91-TIS. Replaced older-style distributor supplied by TISCO through January SWS259 SWS260 Spark plug wiring set, waterproof neoprene wire core. Universal, 4 cylinder. Waterproof neoprene cables with distributor nipples & plug end clips and wire core. Tractors: 6 cyl. IBK1009 IGP1016D IGS2224LB Not for use in original MF distributor Cap Rotor Points IAT3076HS Condenser MF-3-97

119 3 ELECTRICAL Ignition Parts Ignition Kits Less Rotor Contain: Points, Gauge, Condenser Ignition Kits With Rotor Contain: Points, Gauge, Condenser, Rotor Application Tune Up Kit Tractors: TO20, TO30, TO35, MF35, MF50, MF65, MF85, MF88, MF-ITK-10 MF90. Combines: 92, 592. Industrial Tractor: 202, 204, 302, 304, 356 Tractor Shovel For DELCO distributor with clip-held cap Tractors: MF35, MF50, MH50, MF65, MF135, MF150, MF165, MF-ITK-40 MF175, MF180, MF1100. Industrials: 202, 204, 302, 304, 356 For DELCO distributor with screw-held cap Tractors: TE20, TEA20 For LUCAS distributor Tractors: 11, 16, 21, 22, 22K, 23, 23K, 30, 30K, 33, MH44, 44LP, 44-6, 44-6K, 44 Special K, 44 Special LP, 55, 55LP, 333, 333K, 444, 444K, 444LP, 555, 555K, 555LP, 101 Jr. Combines: 26, 27, 27L, 35, 60, 70, 72, 80, 82, 90, 92, Super 92. Balers: 1. Industrials: 20, 35, 303, 402, 404. Windrowers: 34. Forage Clippers: 2, 20 For AUTOLITE distributor Tractors: MH44-6. Combines: 92, Super 92 For IGZ distributor Combines: 300 For AUTOLITE distributor Combines: 410 Tractors: MF230, MF235 For PRESTOLITE distributor Autolite Spark Plugs Ignition Kit w/rotor ATK1DCR ATK10DSR ATK2ALR ATK2ALR Ignition Kit Less Rotor ATK1DC ATK10DS ATK30MH ATK2AL Electronic Ignition Kit ED4C ED4CP6 ED4S ED6S Spark Plugs AL386 AL386 AL386 AL295 AL386 Replaces AL65 AL295 AL303 AL306 AL386 AL405 AL3076 Heat Range Medium Hot Medium Hot Medium Medium Hot Medium Hot Medium Hot Cold Thread diameter (14mm) (14mm) (14mm) (14mm) (18mm) (14mm) (18mm) Reach 3/4" 3/8" 3/8" 3/8" 1/2" 3/4" 5/8" Hex size 13/16" 13/16" 13/16" 13/16" 7/8" 13/16" 15/16" Tip type Power Standard Standard Standard Standard Standard Standard Plug type Non-resistor Non-resistor Resistor Resistor Resistor Resistor Non-resistor Champion Cross Reference N12Y, N12YC, N13Y J8, J8C, UJ8 J5, J6, J6C, J6J, RJ6, RJ6C, UJ6, J7, J7J, RJ7 RJ8, RJ8C, J11, J11J, RJ11, UJ11G D10, K13, D14, M14, RD14, K15J, D16, D16J, RD16, UD16, D21, D89D Replaces #376, BT8, 18-8, D16 N6, N6C, RN6, N8, N21, RN79G W10, W14, C16C, W18, W20 MF-3-98

120 3 ELECTRICAL Replacement parts to fit Ignition Parts Application Tractors: TO20, TO30, TO35, MF35, MF50, MF65, MF85, MF88, MF90. Combines: 92, 592. Industrial Tractor: 202, 204, 302, 304, 356 Tractor Shovel For DELCO distributor with clip-held cap Tractors: MF35, MF50, MH50, MF65, MF135, MF150, MF165, MF175, MF180, MF1100. Industrials: 202, 204, 302, 304, 356 For DELCO distributor with screw-held cap Tractors: TE20, TEA20 For LUCAS distributor Tractors: 11, 16, 21, 22, 22K, 23, 23K, 30, 30K, 33, MH44, 44LP, 44-6, 44-6K, 44 Special K, 44 Special LP, 55, 55LP, 333, 333K, 444, 444K, 444LP, 555, 555K, 555LP, 101 Jr. Combines: 26, 27, 27L, 35, 60, 70, 72, 80, 82, 90, 92, Super 92. Balers: 1. Industrials: 20, 35, 303, 402, 404. Windrowers: 34. Forage Clippers: 2, 20 For AUTOLITE distributor Points M M M M91 Tractors: MH44-6. Combines: 92, Super 92 For IGZ distributor Combines: 300 For AUTOLITE distributor M91 Combines: Tractors: MF230, MF235 For PRESTOLITE M91 distributor Condenser M M M M M M M M91 Rotor 4 Cyl Cap 6 Cyl Cap Dust Cover Coil M M M M M M M M M M M91 MF-3-99

121 3 ELECTRICAL M M M M M M M91 Ignition & Starter Switches Switch assembly with 2 keys. Tractors: TO20, TO30, TO35, MF35, MF50, MF65. Starter switch, manual. Tractors: TO20, TO30. Push button switch assembly. Tractors: MF35 starter & horn, MF65 starter; others. 5/8" dash or firewall mount. Ignition & starter switch with keys, 3-prong. For gas engines. Tractors: 50, 135, 150, 165, 175, 180, 230, 235, 245, 255, 265, 1100, 1130, 1500, Industrials: 20, 20C, 30, 30B, 40, 2135, 2200, Combines: 410. Skid Steer Loaders: 811. Starter switch. For diesel engines. Tractors: 50, 135, 150, 165, 175, 180, 230, 235, 245, 255, 265, 275, 285, 1080, 1085, 1100, 1105, 1130, 1135, 1150, 1155, 1500, Industrials: 20, 20C, 30, 30B, 31, 40, 50A, 50C, 302, 304, 356, 2135, 2200, Forklift: Switch, starter & heat, with key. For slide-on style terminals (4). For diesel engines. Tractors: TO35, MF35, MF50, MF65, MF85, MF88, MF90. Industrials: 35, 203, 205. Optional on some models with switch M91, check terminals before ordering. Switch, starter & heat, with key. For screw-on style terminals (3). For diesel engines. Tractors: MF35, MF50, MF65, MF90. Industrials: 35, 203, 205. Optional on some models with switch M91. Check terminals before ordering M3 Switch, starter & heat, 6 prongs, includes 2 keys. Tractors: MF231, MF240, MF250, MF253, MF270, MF282, MF283, MF290, MF298, MF360, MF375, MF383, MF390, MF398, MF3050, MF3060, MF3070, MF3090, MF3505, MF3525, MF3545, MF3630, MF3650, MF3680. Industrials: 20D, 20F, 30E, 30H, 40E, 50E, 50F, 50H, 60H. Combines: 750 (s/n & up), 760 (s/n & up), 850, 855, 860, 865. Replaces: M M91, M93. Uses key M91. Replacement Ignition Keys M1 Key for switch M M M91 Key for switches M91 & M91. Can replace key #180923M1, M1 & M1. Key for switch M91 & M3. MF-3-100

122 3 ELECTRICAL Replacement parts to fit Light Switches Neutral Safety Switches M1 L M M1 LSN425 Light switch with knob M1. Tractors: MF135, MF150, MF165, MF175, MF180, MF230, MF235, MF245, MF250 (prior to s/n 2773N01000), MF255, MF265, MF270, MF275, MF285, MF288 (except Brazil), MF290, MF298, MF1080, MF1085, MF1100, MF1105, MF1130, MF1135, MF1150, MF1155, MF1500, MF1505, MF1800, MF1805. Industrials: 20, 20C, 20D, 30, 30B, 30D, 30E, 31, 40B, 40E, 50C, 50D, 50E, 2135, Replaces M1, M1. Heavy-duty light switch, plastic knob, 1/2" diameter, two on-positions, fused 20 amps. Ignition and light index switch plate. Anodized black aluminum, 1-13/16" O.D. Tractors: GAS / LP T035, MF35 (to s/n ), MF40, MF50 (to s/n ), MH50, MF65 (to s/n ), MF85, MF88. Industrials: 202 Workbull, 204 Workbull. Vintage Iron Three position light switch. Hi-Lo Charge. Tractors: Massey Harris: Pony, 22, 30, 30K, 44-6, 81, 82, 101 Jr, 101 Sr, 102 Jr, 102 Sr. Vintage Iron Light switch knob. Says "Lights". Tractors: Massey Harris: Pony, 22, 30, 30K, 44-6, 81, 82, 101 Jr, 101 Sr, 102 Jr, 102 Sr. Vintage Iron M M M M M1 Switch, neutral safety, for bullet type terminal. Tractors: to MF1130; all utility & industrial models. Switch, neutral safety, has blade type terminals. Tractors: MF240*, MF250*, MF253, MF282, MF283 (except Brazil), MF298*, MF360, MF362, MF375, MF383, MF390, MF393, MF398, MF399. Industrial: 40E*. *Optional with M1. Replaces M2. Switch, neutral safety, has blade type terminals. Tractors: MF25, MF130, MF231, MF240*, MF250*, MF270, MF290, MF298*, MF670, MF690, MF698, MF3505, MF3525, MF3545. Industrials: 20D, 30E, 40E*. *Optional with M2. Also used for differential lock switch on tractors: MF360, MF362, MF375, MF383, MF390, MF393, MF398, MF399. Replaces M2, M91. Terminal clip, for neutral safety switch. Tractors: MF35, MF50, MF65, MF135, MF150, MF165, MF175, MF180, MF255, MF265, MF285, MF1100, MF1130. Industrials: 20, 20C, 30, 30B, 30D, 40, 40B, 50, 50A, 50C, 50D, 202, 204, 2135, Neutral safety switch boot. Tractors: MF35, MF40, MF50, MF65, MF85, MF88, MF135, MF150, MF165, MF175, MF180, MF230, MF235, MF245, MF255, MF265, MF275, MF285, MF1080, MF1085, Super 90. Industrials: 20, 20C, 30, 30B, 30D, 31, 40, 40B, 50, 50A, 50C, 50D, 60, 202, 203, 204, 205, 302, 304, 2135, 3165, 2200, 2500, 4500, Vintage Iron MF-3-101

123 3 ELECTRICAL Starter Solenoids & Switches Starters M M M M M91 Solenoid switch, all metal. Tractors: TO35 using 6-volt. Solenoid switch, all metal, 12-volt. Tractors: TO35, F40, MF35, MF50, MF65, MF85, MF90. Industrials: 202, 204, 302, 304, 356 utility gas & LP models. Solenoid assembly, flange mounting to starter. Replaces Delco on starters , , , Gas & diesel applications. 12-volt. Solenoid assembly, saddle mounting to starter. Services most late models, replaces Delco , on starters , , , others. 12-volt. Solenoid assembly, replaces Delco Tractors: MF97, MF1105, MF1150 (prior to s/n 9B31942), MF1800, MF2745, MF2775, MF2805 & others. Combines: 760 using AV8-540 Perkins diesel 12-volt. Replaces M MFGL M M91 Starter assembly, for 6- or 12-volt systems with Continental gas engine. Tractors: TO20, TO30, TO35, F40, MH50, MF50, MF65. Industrials: Early 302, 304, 356. Can replace OEM starters M91/ , M92/ , M91/ , & Tisco starters 7877-E, E, E. Uses M91 drive & M91 solenoid. New Lucas style starter assembly with solenoid. Tractors: MF174-4S, MF184-4, MF194-4F, MF270, MF274-4, 282, 283 (except Brazil), MF290, MF294-4, MF298, MF362, MF375, MF383, MF390, MF390T, MF393, MF398, MF399, MF670, MF690, MF698, MF699, MF3050, MF3060, MF3070. Industrials: 50E. Replaces M91, M91, M3 Can replace M2 Magneti Marelli starter and M1 and M1 Hitachi starter on above models (Lucas 27539, 26410). Starter, NEW, 10 tooth, 12-volt, clockwise. Tractors: MF175, MF180, MF255, MF265, MF275. Industrial: MF10, MF20C, MF20U, MF30, MF30B, MF40, MF40B, MF40U, MF45U, MF50C, MF50E, MF60, MF60B, MF60C, MF60E, MF2500. Replaces M91, M91, M M91 New Lucas style starter assembly 5 with solenoid, cold climate. Tractors: MF231, MF240, MF250, MF253, MF360. Industrials: 20D, 20E, 30H, 40E. Replaces M2, M5. Can replace M2, M3 & M2 Hitachi starters on above models. Replaces Lucas 26411, MF-3-102

124 3 ELECTRICAL Replacement parts to fit M M3 New Lucas style starter assembly. Tractors: MF2640, MF2675, MF2705, MF3090, MF3505, MF3525, MF3545, MF3630, MF3650 (Lucas 27533, 26398). Starter, NEW, 10 tooth, 12-volt, clockwise, 2.8 KW. Tractors: MF3055, MF3075, MF3120, MF3120T, MF3140, MF3655, MF3660, MF3670, MF3690, MF3890, MF6170, MF6180, MF6270, MF6280, MF6290, MF8120, MF8140, MF8150, MF8160, MF8210, MF8220, MF8240, MF8250. Replaces R1, R1, M1, M1, R1, R01A, M M M1 Starter Parts Starter drive housing. Fits 12-volt Delco starter Tractors: TO35, MF35, F40, MF50, MF65. Industrials: 202, 204 (replaces Delco ). Brush, services Delco Tractors: TO20, TO30, TO35. 4 required. Starter Flywheel Ring Gears TP-RE M M M M M91 Starter Drives Drive assembly, services Auto-Lite starters. For Massey Harris. Tractors: 33, 44, 44K, 44-6, 55, 55K, 55D. Drive assembly, held on with keyway and set screws. Tractors: TO20, TO30, TO35. Services Delco starter , Drive assembly, hole in middle. For gas engines. Tractors: MF35, MF50, MF65. Industrials: 202, 204, 302, 356. Services starter Drive assembly. For Continental Z145. Tractors: MF135, MF150. Replaces Delco Services starter Drive assembly for Delco starters. Fits all MF diesel models; Perkins gas models M M1 Flywheel ring gear. For Continental gas engine. Tractors: TO20, TO30, TO35, MF35, MF50, MF65, MF135, MF150, MF165, MF175, MF teeth, 13-5/8" I.D. Flywheel ring gear. 115 teeth, 13-7/16" ID. For Perkins engine. Tractors: MF135, MF150, MF154S, MF165, MF168, MF174S, MF178, MF184, MF185, MF188, MF194, MF194F, MF230, MF235, MF240, MF245, MF250, MF253, MF255, MF265, MF275, MF283, MF285, MF290, MF333, MF340, MF350, MF355, MF360, MF362, MF365, MF374S, MF375, MF383, MF390, MF393, MF394S, MF398, MF3050, MF3060, MF3065, MF3070, MF3075, MF35, MF65, MF4225, MF4235, MF4240, MF4245, MF4255, MF4265, MF4325, MF4335, MF4345, MF4355, MF590, MF690, MF6120, MF6140, MF6150, MF6235, MF6245, MF6255, MF6265. Industrial Tractors: 20, 203, 205, 20C, 20D, 20E, 20F, 2135, 30, 302, 304, 30B, 30D, 30E, 30H, 3165, 356, 40, 40B, 40E, 50, 50C, 50D, 50E, 50H, 50H, 60H. Combines: 410. Replaces , , M M91 Drive assembly, heavy-duty replacement for M91. Fits all MF diesel models & Perkins gas models with Delco starter. MF-3-103

125 3 ELECTRICAL Battery Cables & Straps Voltage Regulators VR1816 Voltage regulators, 12 volt. Tractors: MH333D, MH444D using Delco generators , M92 Voltage regulator, 6-volt. Tractors: TO20, TO30, TO35. Tisco part number VR1814. Lengths shown are from terminal centers M M M M91 Cable, starter switch to starter. Tractors: TO20, TO30. 16" long. Ground strap. Tractors: TE20, TO20, TO30, TO /2" long. Cable, battery to switch. Tractors: TE20, TO20, TO30; battery to ground for tractors: MF85, MF88 gas. 21" long. Cable, battery to solenoid. Tractors: TO35; battery to ground for tractors: MF35 gas, MF85D, MF88D, MF Super 90 gas. 14-1/2" long. Battery & Hood Hardware M M91 Voltage regulator, 12-volt. For models using generators. Tractors: TO35, MF25, F40, MF35, MF65, MF85, MF88, MF Super 90, MF135, MF150, MF165, MF175, MF180, MF202, MF204, MF203, MF205, MF2135, MF3165. Combines: SP300, SP410, SP510. Voltage regulator, 12-volt. For MF tractors using Delco alternators, replaces Generator Cutout for Autolite CB4014 Generator cutout for Autolite, 6-volt. For most MH models to M M1WN M1WN Bolt with special wing nut, for hood latch assembly. Tractors: TO " dia., 5.25" long. Bolt with wing nut, for hood latch assembly & battery tie rod. Tractors: MF35, MF50, MF135. 5/16"-24 x 5" overall. Battery tie bolt with wing nut. Tractors: MF35, MF50, MF135. 1/4"-20 x 10-3/4" overall. Generator Parts M91 Brush for 12-volt generator, 2 required M3 Generator ball bearing, double-shielded, services newer 12-volt generators. MF-3-104

126 3 ELECTRICAL Replacement parts to fit Alternator Conversion Kit Alternators TO30ALT12V Updates older 6-volt tractors to 12-volt charging system. Kit includes rebuilt unicharge alternator with pulley, internal self-exciting regulator, 12-volt resistor, wiring harness, brackets, hardware, & instructions. Alternator conversion kit, for tractors less tach drive. Tractor: TO30. Uses alternator repair kit ARKSE7. Generic Alternators Sold outright - no cores to bother with. No deposit... No return Alternator, 63 amp., internal regulator. 3 terminal, 3 o'clock position ALT263SE ALT280SE Alternator, 63 amp., internal regulator. 2 terminal, 3 o'clock position. Alternator, 63 amp unicharge one wire connection. Used in kit ALT. Alternator, 80 amp., internal regulator. 2 terminal, 3 o'clock position. Alternator, 80 amp., internal regulator. 3 terminal, 3 o'clock position. Alternator 80 amp unicharge one wire connection Alternator, 61 amp., uses external regulator, comes with pulley. For most MF Tractors 1965 & later. Replaces 52 amp Sold outright only, no core charge. Uses alternator repair kit ARK E M M1 Alternator, 42 amp., internal regulator. 2 terminal 3 o clock position. Exchange alternator. Tractors: MF135, MF150, MF1100, MF1130. Industrials: 20, 30, 40, 50 using Delco Services new M91 & M91, 40 amp. Pulley included. Use alternator repair kit ARK-1. Alternator, NEW, 55 amp, 12 volt, clockwise. Tractors: MF154, MF184, MF194, MF194-4, MF240, MF243, MF245, MF250, MF253, MF255, MF300, MF350, MF360, MF364, MF365, MF373, MF374, MF375, MF377, MF383, MF384, MF387, MF390, MF390T, MF393, MF396, MF397, MF398, MF399, MF699. Replaces M91, M1. New alternator assembly, 65 amp. Tractors: MF240, MF250, MF253, MF270, MF283, MF290, MF298, MF360, MF364S, MF374S, MF375, MF383, MF384S, MF390, MF390T, MF393, MF394S, MF398, MF399, MF670, MF690, MF698, MF699. Industrials: MF20D, MF20E, MF20F, MF30E, MF30H, MF40E, MF50E. Replaces: M91, M92, M92, M92, M91, M91, M91, M91, (Lucas 24087, 24124). MF-3-105

127 3 ELECTRICAL M1 Alternator, New, 70 amp, 12 volt, clockwise. Tractor: MF6110, MF6120, MF6130, MF6140, MF6160, MF6170, MF6180, MF6235, MF6245, MF6255, MF6265, MF6270, MF6280, MF6290. Replaces M91, M, M. Internal Voltage Regulator For Alternators AP3158 Alternator Pulleys Pulley, 3-1/8" dia., 5/8" shaft bore, 2 grooves for 1/2" wide v-belt. Use with alternator ALT Alternator Repair Parts M91 Internal voltage regulator for MF/Delco alternators. Tractors: MF230, MF235, MF245, MF255, MF265, MF275, MF285, MF1085, MF1105, MF1135, MF1155, MF1500, MF1505, MF1800, MF1805, MF2675, MF2705, MF2745, MF2775, MF2805. Industrials: 20C, 30B, 30D, 40B, 50C. Replaces M1 & Delco Services Alternators: DELCO MF DELCO MF M M M M M M M M M M91 * & HD are not interchangeable. Fuse Holders HD BHK1 Bearing, alternator front. Bearing, alternator rear. Diode trio, Delco alternator. Rectifier assembly, Delco alternator. Cannot be replaced by HD Rectifier assembly, Delco alternator. Will not replace Brush holder kit, alternator M M91 Fuse holder, chassis mount with threads for securing nut. Tractors: 135, 150, 165, 175, 180, 230, 235, 245, 255, 265, 275, 285. Industrials: 20, 30, 40, 31, 20C, 30B, 40B, 50C, Replaces M91. Fuse holder, in line assembly. Tractors: 150, 165, 175. Industrials: 30, 31, 40. BHK M91 AMG60 Brush holder kit, alternator (HD brush holder & brushes) Ammeter Assembly Ammeter gauge. For all TO & MF models using amperes, non-luminous. For 2" dia. hole. Ammeter gauge has range, non-luminous, fits 2" dia. hole, stainless bezel, black background, white letters, & white pointer M1 Fuse holder, less fuse. 20 amp, fits ½" hole. Tractors: MF135, MF150, MF165, MF175, MF180, MF230, MF235, MF245, MF255, MF265, MF275, MF285. Industrial: 20, 20C, 30, 30B, 31, 40, 40B, 50C, 2135, 2200, 2500, Vintage Iron Halogen Bulb Halogen bulb 12-volt, 55 watt (L4970). MF-3-106

128 3 ELECTRICAL Replacement parts to fit Sealed Beam Bulbs Taillight Assemblies M91 Light Ring. Retained to headlight with 2 screws. Grey primer with ground wire. Tractors: TO20, TE20, TEA20, TO30, TO35, MF40, MF50, MH50, MF65, MF85, MF88, Super 90. Vintage Iron M M M M M M M1 H7609 L4511 L4019 L4411 Sealed beam bulb 6-volt. Tractors: TE20, TO20, TO30, TO35 (L4019). Sealed beam bulb 12-volt. Tractors: TE20, TO20, TO30, TO35 (early hood mount), MH50, MF50, MF65. Replaces M91 (L4419). Sealed beam bulb 12-volt. Early fender mount models. Tractors: TO35, MH50, MF50, MF65. Inner or upper fender mount models. Tractors: MF150, MF165, MF175, MF180, MF1100, MF1130 (L4411). Sealed beam bulb 12-volt. Outer flat fenders tractor: MF135; Outer or lower fender all late MF tractors, 12-volt (L4406). Sealed beam bulb, 12-volt. Tractors: MF35, MF50, MF65 (L4419). Sealed beam bulb. Tractors: MF235, 255, 265, 275, volt (L44401), 3 spade terminals. 12-volt, halogen sealed beam bulb. 4-1/2" dia. screw terminals (H7606). Halogen sealed beam bulb. 4-1/2" dia., 5, 200 candle power. Trapezoidal light pattern. Can be used in place of L volt sealed beam bulb, 4-1/2" dia. 6-volt sealed beam bulb, 5-3/4" dia. 12-volt sealed beam bulb, 4-1/2" dia HA M R R1 Round red tail light assembly with license lamp window. 4-1/2" diameter /8" c-c mounting stud. Vintage Iron Taillight assembly. Includes 12-volt bulb & mounting bolts. Painted black. Solid bucket 1-3/4" c-c mounting studs. Tractors: TE20, TO20, TO30, TO35, MF35, MF40, MF50, MH50, MF65, MF85, MF90, MF135. Industrials: 202, 203, 204, 205. Vintage Iron Sealed-beam combination rear light bulb, 12-volt. 4-1/2" diameter sealed beam combo light bulb (used with small separate bulb). Vintage Iron Warning Light Rectangular fender and cab mount warning light One red and one amber lens with amber side marker, black ABS mount --- Single contact bulbs #57 (small) & #1156 (large) 12 Volt " wide, 1/2" diameter stud. Serviceable for models with rectangular warning lights. Vintage Iron L volt sealed beam bulb, 4-1/2" dia. L volt sealed beam bulb, 5-3/4" dia. L volt bulb, flood volt warning light, mounts on fender or cab. Two 4" amber lenses. L volt bulb, replacement bulb for MF-3-107

129 4 POWER TRAIN Brake Shoes Brake Cylinders M2 Brake cylinder, Master assembly. Tractors: MF360 (to engine s/n V39466), MF375 (to engine s/n V39466), MF383 (to engine s/n V39466), MF390 (to engine s/n V39466), MF398 (to engine s/n V39466), MF399 (to engine s/n V39466) M93AF M93AF M91 Kit, 4 shoes with linings bonded. 2" x 15" total shoe length. Tractors: TO20, TO30. Two wheel set. Kit, 4 shoes with linings bonded. 2" x 19-1/2" total shoe length. Tractors: TO35, MF35, F40, MF50, MF135, MF150, MF230, MF235 (std. & orch.), MF245. Two wheel set. Kit, 2 shoes with linings. 2" wide. Priced and sold per pair. Tractors: MF231, MF240. One wheel set. Brake Drum M M93 Brake cylinder, Master assembly. Tractors: MF360 (engine s/n V39466 & up), MF362, MF375 (engine s/n V39467 & up), MF383 engine s/n & up), MF390 (engine s/n V39466 & up), MF390T (engine s/n V39466 & up), MF398 (engine s/n V39466 & up), MF399 (engine s/n V39466 & up). Brake cylinder, Slave assembly (LH). Tractors: MF360, MF362, MF375, MF383, MF390, MF390T, MF393, MF396, MF398, MF M1 Brake cylinder, Master assembly. Tractors: MF690 (w/small double reservoir), MF698 (w/small double reservoir), MF698T, MF M5 Brake drum. Tractors: TO35, MF35, F40, MH50, MF50, MF135 (except orchard), MF150, MF230, MF235 (except orchard), MF240, MF245 (except orchard). Industrials: 20, 20C, 20D, 30 turf, 35, 40, 202, 204, 2135, 2200, Replaces M M M5 Brake Cylinder, Slave assembly. Tractors: MF270, MF290, MF298, MF670, MF690, MF698, MF698T, MF699. Industrials: 24 Telescopic handler, 25 Telescopic handler, 30E, 30H, 40E, 50E, 50E, 50H, 60H. Master brake cylinder assembly. 2 used per tractor. Tractors: MF3050, MF3065, MF3070, MF3075, MF3090, MF3095, MF3120T, MF3125, MF3645, MF3655, MF3670, MF3690, MF6150, MF6170, MF6180, MF8120, MF8140, MF8150, MF8160. Replaces M M91 Master brake cylinder assembly (3 ports) (Dia ). Tractors: MF362, MF365, MF375, MF383, MF390, MF390T, MF393, MF396, MF398, MF399. MF-4-108

130 4 POWER TRAIN Replacement parts to fit M M M93 Master brake cylinder assembly. (Dia ). Tractors: MF1134, MF1024, MF274SK, MF294S, MF560, MF565, MF575, MF590, MF592, MF595, MF690, MF698; Combine Series: MF660, MF830, MF835, MF810. Brake cylinder, Slave assembly (RH). Tractors: MF360, MF362, MF375, MF383, MF390, MF390T, MF393, MF396, MF398, MF399. Brake cylinder, Slave assembly (LH). Tractors: MF360, MF362, MF375, MF383, MF390, MF390T, MF393, MF396, MF398, MF399. Brake Actuators M92AF M1AF Brake Discs Measure disc diameter before ordering. Some models have optional disc. Order M92, 7-1/8" dia. for malleable axles M1, 8-7/8" dia. for cast axles. Brake disc, 7-1/8" x 4", 27 splines. Tractors: MF65, MF85, MF88, MF90 Super, MF135, MF150, MF165, MF175, MF180. Industrials: 30, 31, 40, 50, 203, 205, 302, 304, Tractor Shovel: 356. Forklift: Replaces M1. Brake disc, 8-7/8" x 6", 27 spline. Tractors: MF135, MF165, MF175, MF180, MF235, MF255, MF265, MF275, MF285, MF1080, MF1085. Industrials: 30, 31, 40. Replaces M M M91 Brake actuator assembly (RH side). Tractors: MF360 (w/tangential brakes), MF362, MF365, MF375 (w/tangential brakes), MF390 (w/tangential brakes), MF390T (w/tangential brakes), MF393, MF396, MF398 (w/tangential brakes), MF399, MF4225, MF4235, MF4243, MF4245, MF4253, MF4255, MF4260, MF4263, MF4270, MF4325, MF4335, MF4345, MF4355, MF4360, MF4370. Brake actuator assembly (LH side). Tractors: MF360 (w/tangential brakes), MF362, MF365, MF375 (w/tangential brakes), MF390 (w/tangential brakes), MF390T (w/tangential brakes), MF393, MF396, MF398 (w/tangential brakes), MF399, MF4225, MF4235, MF4243, MF4245, MF4253, MF4255, MF4260, MF4263, MF4270, MF4325, MF4335, MF4345, MF4355, MF4360, MF M M2 Friction disc, used in wet disc brake system. 8-1/2" O.D.,.190" thick. OEM quality, appearance & performance. Tractors: MF245, MF250, MF255, MF265, MF275, MF285, MF1085. Industrials: 11 wheel loader UK, 30B, 30D, 31, 40, 40B, 50A, 50C, 50D, 60 backhoe/loader. Forklifts: 4500, Sugar Harvesters: 102, 201. Intermediate steel disc, used in wet disc brake system. OEM quality, appearance & performance. Tractors: MF245, MF250, MF255, MF265, MF275, MF285, MF1085. Industrials: 11 wheel loader UK, 30B, 30D, 31, 40, 40B, 50A, 50C, 50D, 60 backhoe/loader. Forklifts: 4500, Sugar Harvesters: 102, 201. Brake Disc Actuating Balls Steel ball, brake actuating, 7/8" diameter Steel ball, brake actuating, 1" diameter. MF-4-109

131 4 POWER TRAIN M M M1 Disc Brake Parts Spring, actuator disc return for disc brakes. Tractors: MF154-4, MF184-4, MF235 orchard, MF240, MF245, MF250, MF253, MF255, MF265, MF270, MF275, MF282, MF283, MF285, MF290, MF298, MF360, (prior to s/n V39466), MF375 (prior to s/n V39466), MF383 (prior to s/n V39466), MF390 (prior to s/n V39466), MF398 (prior to s/n V39466), MF399 (prior to s/n V39466), MF670, MF690, MF698, MF699. Industrials: 30B, 30D, 30E, 40B, 40E, 50C, 50D, 50E, 50F. Forklift: 4500, For tractors with cast iron axle: MF135, MF165, MF175, MF180. Industrials: 30, 31, 40, 50A. Spring, actuator disc return for disc brakes. 3 used in each actuator. Tractors: MF65, MF85, MF88, MFSuper90, MF95, MF97, MF150, MF154S, MF174S, MF254-4, MF274-4, MF294-4, MF333, MF444. Industrials: 50, 203, 205, 302, 304, 356 tractor shovel, Forklift: Tractors with malleable iron axle: MF135, MF165, MF175, MF180, MF1080. Industrials: 30, 31, 40. Seal, for brake pull rod, dry disc brakes. Tractors: MF65, MF85, MF88, MF90, MF135 (orchard with malleable iron axle), MF150, MF154-4, MF154-4S, MF165 (with malleable iron axle), MF174-4S, MF175 (with malleable iron axle), MF180 (with malleable iron axle), MF184-4, MF254-4, MF274-4, MF285, MF294-4, MF1080, MF Industrials: 30 (with malleable iron axle), 31 (with malleable iron axle), 40 (with malleable iron axle), 50, 203, 205, 302, 304, M M1 Rod & clevis, 6-1/4" from end of rod to hole center. Disc brake lever to actuating links, except models with cast axle housings. Tractors: MF65, MF135, MF150, MF165, MF175, MF180, MF1080. Industrials: 30, 40, 50, 203, 205, 302, 304, Forklift: 2500 Seal, for brake pull rod, wet disc brakes. Fits into left & right lever brackets. Tractors: MF154-4S, MF174-4S, MF194-4, MF194-4F, MF245, MF250, MF253, MF254-4, MF255, MF265, MF270, MF274-4, MF275, MF282, MF283, MF285, MF290, MF294-4, MF298, MF670, MF690, MF698, MF699, MF1085. Industrials: 30D, 30E, 40E, 50D, 50E. Replaces M1. Brake Cable Assemblies M93 Hand brake cable (RH) 49-1/2" length. Tractors: All 2WD; MF231S, MF240, MF241, MF243, MF253, MF M M M M M91 Hand brake cable (LH) 62" length. Tractors: All 2WD; MF231S, MF240, MF241, MF243, MF253, MF263. Hand brake cable (RH) 49" length. Tractors: MF240 (2WD w/wet brakes; s/n A20286 & up), MF240 (4WD; s/n A20286 & up), MF243 (4WD), MF253 (4WD), MF263 (4WD). Hand brake cable (LH) 60" length. Tractors: MF240 (2WD, w/wet brakes; s/n A20286 & up), MF240 (4WD; s/n A20286 & up), MF243 (4WD), MF253 (4WD), MF263 (4WD). Hand brake cable (RH) 49". For tractors with Concentric brakes W/O spacer. Tractors: MF360, MF375, MF383, MF390, MF398 (all to engine s/n V39465). Hand brake cable (LH) 60". For tractors with Concentric brakes W/O spacer. Tractors: MF360, MF375, MF383, MF390, MF398 (all to engine s/n V39465). MF-4-110

132 4 POWER TRAIN Replacement parts to fit M M M M M M92 Hand brake cable (RH) 44". For tractors with concentric brakes with spacer. Tractors: MF360, MF375, MF390, MF398, MF399 (all to engine s/n V39465). Hand brake cable (LH) 55". For tractors with concentric brakes with spacer. Tractors: MF360, MF375, MF390, MF398, MF399 (all to engine s/n V39465). Hand brake cable (RH) 52". For tractors with Tangential brakes W/O spacer. Tractors: MF360, MF362, MF365, MF375, MF383, MF390, MF390T, MF393, MF396, MF398, MF399. Hand brake cable (LH) 62-1/2". For tractors with Tangential brakes W/O spacer. Tractors: MF360, MF362, MF365, MF375, MF383, MF390, MF390T, MF393, MF396, MF398, MF399. Hand brake cable (RH) 46". For tractors with Tangential brakes with spacer. Tractors: MF362, MF365, MF375, MF383, MF390, MF390T, MF393, MF396, MF398, MF399. Hand brake cable (LH) 57". For tractors with Tangential brakes with spacer. Tractors: MF362, MF365, MF375, MF383, MF390, MF390T, MF393, MF396, MF398, MF399. Clutch Kit M M M M91 Clutch Cover Assemblies For Single Clutch Pressure plate assembly, NEW. 9" SINGLE CLUTCH, 6 SPRINGS. Tractors: TO20, TO30, TO35, MF25, MF35, MF50, MH50, MF202, MF204. Replaces M91, 18355M91. Clutch cover assembly, 11", 10-spline plate, 1-3/4" hub. For split torque single clutch. Tractors: MF165, MF175, MF180. Clutch Cover Assemblies For Dual Clutch Dual clutch assembly, 12" with 10", 25-spline PTO disc. Supplied same as OEM, less 12" disc M92, order separately if needed. Tractors: MF275, MF282, MF283 (except Brazil), MF290, MF383, MF390. Replaces M92. For replacement PTO disc use * Pressure plate with PTO disc only. Order bearings and engine disc separately. Pressure Plates Clutch Pressure Plate Assembly, 8", diaphragm style. Tractors: MF205, MF205-4, MF M94K Clutch kit, for 12" split torque clutch. Kit contains remanufactured pressure plate assembly 12", 12 springs, 1-5/8" hub, 25 spline; NEW disc, H.D. 12", woven lining, 1-1/8" hub. 10 spline; new release & pilot bearings. Tractors: MF285, MF M92 Pressure Plate Assembly, 13", 25 spline 1.5" hub. Tractors: MF375, MF390, MF390T, MF393, MF394S, MF396, MF398, MF399, MF4243, MF4245, MF4253, MF4255, MF4260, MF4263, MF4265, MF4270, MF4345, MF4355, MF4360, MF4370. Used in TISCO kit M92KT. MF-4-111

133 4 POWER TRAIN Clutch Discs For Single and Dual Clutches M91AF Clutch disc, 9", 10-spline, 1-3/8" hub spring loaded with woven heavy-duty lining. For single clutch. Tractors: TO20, TO M M M M M92 Clutch disc, 9", 10-spline, 1-1/8" hub, no damper springs, organic lining. For single clutch. Tractors: TO35, MF35, MH50, MF50, MF135. Clutch disc, 10", 25-spline. For live PTO. For dual clutch M91 or M92. Tractors: MF275, MF282, MF283 (except Brazil), MF290, MF383, MF390. For other dual clutches. Tractors: MF 250, MF270, MF375. Industrials: 20D (with HD clutch), 40E. Replaces M91. Clutch disc, 11", 10-spline, 1-1/8" hub, damper springs, organic lining. For split torque single clutch. Tractors: MF165, MF175, MF180, MF255, MF265. Clutch disc, standard, 12", 10 spline, 1-1/8" hub, with damper springs, organic linig. For split torque single clutch. Tractors: MF240, (s/n 2773N01001 & up), MF270, MF275, MF290, MF670, MF690. For dual clutch. Tractors: MF231, MF240, MF250, MF253, MF270, MF275, MF282, MF283 (except Brazil), MF290. Industrial: 20D. Replaces M94, M93. Clutch disc, 12", 21 spline, 1-1/8" hub, no damper springs, organic lining. For split torque single clutch. Tractors: MF360, MF362, MF390. For dual clutch. Tractors: MF390. Replaces M M91KT M91KT M92KT M91KT Double Clutch Kit Assemblies Double clutch kit assembly "NEW" 11" PP with 1.5" hub 10 spline PTO disc. Includes 11" Rigid Clutch Disc, 10 spline.933" hub, New release & pilot bearing with clutch alignment tool. Tractors: F40, MH50, MF135, MF150; MF35, TO35 (late production). Industrials: 20, 2135, 2200, 40. Double clutch kit assembly "NEW" 11" PP with 1.5" hub 25 spline PTO disc. Includes 11" Rigid Clutch Disc, 10 spline.933" hub, New release & pilot bearing with clutch alignment tool. Tractors: MF135, MF150, MF165, MF175, MF175 U.K., MF178 U.K., MF180, MF230, MF235, MF245, MF255, MF265, MF35, MH50, MF65, TO35. Industrials: 20, 20C, 2135, 30, Split Torgue clutch kit assembly "NEW" 13" PP with 1.5" hub 25 spline. Includes 12.5" 5 PAD Disc, 21 spline 1.00" hub, New release & pilot bearing. Contains clutch alignment tool. Tractors: MF375, MF390, MF390T, MF393, MF394S, MF396, MF398, MF399, MF4243, MF4245, MF4253, MF4255, MF4260, MF4263, MF4265, MF4270, MF4345, MF4355, MF4360, MF4370. Double clutch kit assembly, Medium spring, "NEW" 11" PP 1.5" hub 10 spline PTO disc, Includes 11" Rigid clutch Disc, 10 spline.933" hub, New release & pilot bearing with clutch alignment tool. Tractors: MF135, MF150, MF165, MF175, MF175 U.K., MF178 U.K., MF180, MF235, MF245, MF255, MF265, MF35, MH50, MF65, TO35. Industrials: 20, 20C, 2135, 30, MF-4-112

134 4 POWER TRAIN Replacement parts to fit M92KT M94KT M91KT M91KT Double clutch kit assembly, "NEW" 12" PP 25 spline PTO disc, Includes 12" Rigid clutch Disc, 21 spline.987" hub, New release & pilot bearing. Contains clutch alignment tool. Tractors: MF231, MF240P, MF240S, MF253, MF261, MF263, MF265S, MF271, MF281, MF285S, MF360, MF362, MF365, MF375, MF383, MF390, MF390T. Industrials: 20D, 20F, 30E, 40E. Double clutch kit assembly, "NEW" 12" PP 25 spline PTO disc, light-duty springs. Includes 12" Rigid clutch Disc, 10 spline 1-1/8" hub, New release & pilot bearing with clutch alignment tool. Tractors: MF165, MF175, MF175 U.K., MF178 U.K., MF231, MF240P, MF240S, MF253, MF261, MF263, MF270, MF271, MF275, MF281, MF282, MF283, MF285, MF290 U.K, MF670, MF690. Industrials: 20D, 20E, 20F, 30E, 40E. Double clutch kit assembly, "NEW" 11" PP 1.025" hub, 25 spline PTO disc, Includes 11" Rigid clutch Disc, 10 spline.933" hub, New release & pilot bearing with clutch alignment tool. Tractors: MF135, MF150, MF165, MF175, MF175 U.K., MF178 U.K., MF180, MF235, MF245, MF255, MF265, MF35, MH50, MF65, TO35. Industrials: 20C, 2135, 30, 30B, 30D, 3165, 40B. Double clutch kit assembly, Heavy duty "NEW" 11" PP 1.625" hub, 25 spline PTO disc, Includes 11" Rigid clutch Disc, 10 spline.933" hub, New release & pilot bearing with clutch alignment tool. Tractors: MF175, MF175 U.K., MF178 U.K., MF255, MF M91KT AG08TOOL AG09TOOL AG10TOOL M1 Double clutch kit assembly, "NEW" 12" PP 1.625" hub, 25 spline PTO disc, heavy-duty springs. Includes 12" Rigid clutch Disc, 10 spline 1-1/8" hub, New release & pilot bearing with clutch alignment tool. Tractors: MF165, MF175, MF175 U.K., MF178 U.K., MF231, MF240P, MF240S, MF253, MF261, MF263, MF265S, MF270, MF271, MF271, MF271E, MF275, MF281, MF281, MF281E, MF282, MF283, MF285, MF285S, MF383, MF390, MF471, MF481, MF670, MF690. Industrials: 20D, 20E. Clutch Alignment Tools Clutch Alignment tool, For dual stage type w/1-1/8 10 spline and 1-3/4 10 spline. For M91 KT, M91KT. Clutch Alignment tool, For Dual Stage, 1-1/8 21 splines, 1-5/8 25 splines. For M92KT, M92KT. Clutch Alignment tool, For Dual stage type w/1-1/8 10 splines and 1-5/8 25 splines. For M94KT, M91KT, M91KT, M91KT, M91KT. Clutch Cover Repair Parts Clutch spring, red, 2 13/16" long. For pressure plate in single & dual clutch assemblies. Tractors: MF231, MF240, MF250, MF270, MF275, MF282, MF283 (except Brazil), MF290, MF383, MF390, MF670, MF690. Industrials: 20D, 30E, 40E, 50E. Replaces spring M1, lavender 2-7/16" long, in dual clutches using pressure plate M1, must replace all springs. Tractors: MF65, MF165, MF175, MF255, MF265. Industrials: 30, MF-4-113

135 4 POWER TRAIN M M M1 Insulating washer, for pressure plate spring. For dual clutch. Tractors: TO35, MF35, MF50, MF65, MF135, MF150, MF165, MF175, MF180, MF230, MF231, MF235, MF240, MF245, MF250, MF253, MF255, MF265, MF270, MF275, MF282, MF283 except Brazil, MF290, MF360, MF362, MF375, MF383, MF390. Industrials: 20, 20C, 20D, 30, 30B, 30D, 31, 40, 40B, 40E. For split torque single clutch. Tractors: MF240, MF270, MF275, MF290, MF298, MF360, MF362, MF375, MF390, MF393, MF398, MF399, MF670, MF690, MF698, MF699. Industrials: 30E, 40E, 50E. Replaces M91. Adjusting bolt, 3/8" x 25/32" NF, for clutch release lever. For dual clutch. Tractors: TO35, MF35, MF50, MF65, MF135, MF150, MF165, MF175, MF180, MF230, MF231, MF235, MF240, MF245, MF250, MF253, MF255, MF265, MF270, MF275, MF282, MF283 (except Brazil), MF290, MF360, MF362, MF375, MF383, MF390. Industrials: 20, 20C, 20D, 30, 30B, 30D, 31, 40, 40B, 40E. For split torque single clutch. Tractors: MF240, MF270, MF275, MF290, MF298, MF360, MF362, MF375, MF390, MF393, MF398, MF399, MF670, MF690, MF698, MF699. Industrials: 30E, 40E, 50E. Replaces M1. Use with clutch release levers M1 & M2. Lock nut, 3/8" NF, for clutch release lever adjusting bolt. Use with M1 on same applications. Clutch release lever, for split torque single clutch or dual clutch. Tractors: MF231, MF240, MF250, MF253, MF270, MF275, MF282, MF283 (except Brazil), MF290, MF298, MF383, MF390, MF398, MF399, MF670, MF690, MF698, MF699. Industrials: 20D, 30E, 40E, 50E. Replaces M M M M M M M1 Torsion spring for clutch release lever. For split torque single clutch or dual clutch. Tractors: MF231, MF240, MF250, MF253, MF270, MF275, MF282, MF283 (except Brazil), MF290, MF298, MF383, MF390, MF398, MF399, MF670, MF690, MF698, MF699. Industrials: 20D, 30E, 40E, 50E. Pivot pin, for clutch cover release lever to cover..30" dia., 2.68" L. Tractors: MF240, MF250, MF253, MF270, MF275, MF282, MF283 (except Brazil), MF290, MF298, MF383, MF390, MF398, MF399, MF690, MF698, MF699. Industrials: 20D, 30E, 35, 50E. Also used as an alternate on clutch covers manufactured in the United Kingdom. Tractors: MF35, MF50, MF65. Industrial: 20. Hair pin, use with pivot pin M1 on same applications. Clevis pin, 5/16" x 7/8", clutch release lever to link. For dual clutch. Tractors: TO35, MF35, MF50, MF65, MF135, MF150, MF165, MF175, MF180, MF230, MF235, MF245, MF255, MF265. Industrials: 20, 20C, 30, 30B, 30D, 31, 40, 40B, 202, 203, 302, 304, 2135, Link, clutch release lever to pressure plate. For split torque single clutch or dual clutch. Tractors: MF231, MF240, MF250, MF253, MF270, MF275, MF282, MF283 (except Brazil), MF290, MF298, MF383, MF390, MF398, MF399, MF670, MF690, MF698, MF699. Industrials: 20D, 30E, 40E, 50E. Replaces M91. Clevis pin, 5/16" x 1-1/2", clutch release lever link to pressure plate. For split torque single clutch or dual clutch. Tractors: MF231, MF240, MF250, MF253, MF270, MF275, MF282, MF283 (except Brazil), MF290, MF298, MF383, MF390, MF398, MF399, MF670. MF-4-114

136 4 POWER TRAIN Replacement parts to fit Dual Clutch Assemblies & Components Assembly 1 includes itmes 2 thru 11 only. Items A, B, 12 must be ordered separately. Application Tractors: TO35 (to s/n & s/n to ), F40, MH50 (to s/n , early production), MF35 Complete Assembly 1 Tractors: TO35, MF35 (late production), M91 MF50. Industrial Tractors: 20, 40 (w/10 spline PTO disc) Industrial Tractors: 20, 20C (w/25 spline PTO M91 disc) Industrial Tractors: 20C (except Turf), 30, M91 30B, 30D, 40B (w/25 spline PTO disc) Tractors: MF65. Industrial Tractors: 30 (w/ M91 spline PTO disc) Tractors: MF135, MF150 (w/10 spline PTO M91 disc) Tractors: MF135, MF150 (w/25 spline PTO M91 disc) Tractors: MF165 (w/10 spline PTO disc) M91 Tractors: MF165 (w/25 spline PTO disc) M91 Tractors: MF175, MF180 (w/10 spline PTO M91 disc) Tractors: MF175 (w/25 spline PTO disc) M91 Tractors: MF230 (w/25 spline PTO disc) M91 Tractors: MF235, MF245 (except Orchard) M91 (w/25 spline PTO disc) Tractors: MF255 early production (w/25 spline M91 PTO disc) Tractors MF255 late production (w/25 spline M91 PTO disc) Tractors: MF265 (w/25 spline PTO disc) M91 Tractors: MF270 (w/25 spline PTO disc) Tractors MF275, MF282, MF283 (except M91 Brazil), MF290, MF383, MF390 (w/25 spline PTO disc) Tension Spring M M M M M M M M M M M M M M M M M1 Release Lever M M M M M M M M M M M M M M M M M1 Lever Pin M M M M M M M M M M M M M M M M M1 PTO Clutch Disc M M M M M M M M M M M M M M M M M M91 MF-4-115

137 4 POWER TRAIN Dual Clutch Assemblies & Components Assembly 1 includes itmes 2 thru 11 only. Items A, B, 12 must be ordered separately. Application Flywheel Plate 8 Tractors: TO35 (to s/n & s/n to ), F40, MH50 (to s/n , early production), MF35 Tractors: TO35, MF35 (late production), MF M1 Industrial Tractors: 20, 40 (w/10 spline PTO disc) Industrial Tractors: 20, 20C (w/25 spline PTO M1 disc) Industrial Tractors: 20C (except Turf), 30, 30B, M1 30D, 40B (w/25 spline PTO disc) Tractors: MF65. Industrial Tractors: 30 (w/ M1 spline PTO disc) Tractors: MF135, MF150 (w/10 spline PTO disc) M1 Tractors: MF135, MF150 (w/25 spline PTO disc) M1 Tractors: MF165 (w/10 spline PTO disc) M1 Tractors: MF165 (w/25 spline PTO disc) M1 Tractors: MF175, MF180 (w/10 spline PTO disc) M1 Tractors: MF175 (w/25 spline PTO disc) M1 Tractors: MF230 (w/25 spline PTO disc) M1 Tractors: MF235, MF245 (except Orchard) (w/ M1 spline PTO disc) Tractors: MF255 early production (w/25 spline M1 PTO disc) Tractors MF255 late production (w/25 spline PTO M1 disc) Tractors: MF265 (w/25 spline PTO disc) M1 Tractors: MF270 (w/25 spline PTO disc) Tractors MF275, MF282, MF283 (except Brazil), MF290, MF383, MF390 (w/25 spline PTO disc) Clutch Spring 9 Lever Link M M M M M M M M M M M M M M M M M M M1 Pressure Plate M M M M M M M M M M M M M M M1 Clutch Disc M M M M M M M M M M M M M M M M M92 MF-4-116

138 4 POWER TRAIN Replacement parts to fit Clutch Pilot Bearings Clutch Release Bearings M M M M M2 Clutch pilot bearing " ID, 1.574" OD, 0.470" width. Tractors: TE20, TO20, TO30, F40, MF35, MH50, MF50, MF65 (except diesel), MF85D, MF Super 90, MF135, MF150, MF165, MF175, MF180, MF235, MF255, MF265, MF275. Clutch pilot bearing, heavy-duty, long lasting stainless steel " ID, 1.574" OD, 0.470" width. Tractors: MF50, MF65, MF85, MF88, MF235, MF245, MF255, MF285, MF1080; industrials: 20, 20C, 30, 30B, 31, 35 utility & turf, 40, 40B, 50, 50A, 50C, 202, 203, 204, 205, 302, 304, 2135, 2200, Skidder: 320. Forklifts: 2500, 4500, Clutch pilot bearing " ID, 1.574" OD, 0.470" width. Tractors: MF240, MF250, MF253, MF270, MF282, MF283 (except Brazil), MF360, MF362, MF375, MF383, MF390, MF393, MF398, MF399, MF670, MF690, MF698, MF699. Industrials: 20D, 30E, 40E, 50E. Replaces Carriers For Clutch Release Bearings Carrier for clutch release bearing. Carrier bore 2.228" (2-1/4" approx.); O.D. 2-1/2". Tractors: MF231, MF240, MF250, MF253, MF270, MF282, MF283, MF290, MF298, MF360, MF362, MF375, MF383, MF390, MF393, MF398, MF399, MF670, MF690, MF698, MF699. Industrial: 20D, 30E, 40E, 50E, 50F. Carrier, for clutch release bearing. Carrier bore 2.130" (2-1/8" approx.); O.D " (2-1/2"); check carrier bore before ordering. For single or dual clutch. Tractors: TO35, MF35, MF50, MF65. Industrials: 20, 202, 203, 302, Use with bearing M2 for dual clutch only M M M M M2 D8NN7580CA M1 Bearing, clutch release, 2.07" I.D., 3.550" O.D.,.810" wide. Tractors: TE20, TO20, TO30, MH44, MH444, MH55, MH555. Combine: 300SP. Bearing, clutch release, 2.49" I.D., 4.10" O.D.,.875" wide, 1.535" front to back. For single clutch. Tractors: TO35, MF35, F40, MF50, MF65, MF135. Industrials: 2135, (A /A ) Bearing, clutch release, 2.480" I.D., 4.100" O.D.,.850" wide. For single clutch with independent PTO. Tractors: MF165, MF175, MF180, MF255, MF265. For dual clutch. Tractors: TO35, MF35, F40, MF50, MF65, MF135, MF150, MF165, MF175, MF180, MF235, MF255, MF265, MF275, MF1100, MF1130. Industrials: 202, 203, 302, Bearing, clutch release, relubricatable. Has notch to allow lubrication. 2-1/2" I.D., 4-1/8" O.D., 13/16" wide. Tractors: F40, MF285, MF1080, MF1085, MF1100, MF1105, MF1130, MF1135, MF1150, MF1155, MF1500, MF1505, MF1800, MF1805, MF2805. Bearing, clutch release, 2.50" I.D., 3.936" O.D. Tractors: MF231, MF240, MF250, MF253, MF270, MF282, MF283, MF290, MF298, MF360, MF362, MF375, MF383, MF390, MF393, MF398, MF399, MF670, MF690, MF698, MF699. Industrials: 20D, 30E, 40E, 50E, 50F. Also used an alternate bearing on carrier M2 for dual clutch. Tractors: TO35, MF35, MF50, MF65. Industrials: 20, 202, 203, 302, Clutch release bearing, 2.50" I.D., 4.090" O.D.,.865" wide. Combines: 760, 860. Replaces M1. Release Bearing (Dual clutch), 2.164" I.D., 3.450" O.D.,.765" Thickness. Tractors: MF1120, MF1125, MF1140, MF1145, MF1160, MF1190, MF1220, MF1240, MF1260. MF-4-117

139 4 POWER TRAIN M1 Bushing For Clutch Release Fork Shaft Bushing, for clutch release fork shafts. 1" I.D. x 1-1/16" x 1-1/2". (2) required for transmission case. Tractors: TO35, MF35, MF50, MF65, MF135, MF150, MF165, MF175, MF180, MF230, MF235, MF240, MF245, MF250, MF253, MF255, MF265, MF270, MF275, MF282, MF283, MF285, MF290, MF298, MF1080, MF1085. Industrials: 20, 20C, 20D, 30, 30B, 30D, 30E, 31, 40, 40B, 40E, 50, 50A, 50C, 50E, 50F, 202, 203. Forklifts: 2500, 4500, M M1 Shifter Knobs and Cover Black knobs with engraved cream color inlay shift pattern. For shift levers with 3/8" NF threads. Machine applicatin of knobs will vary depending on type of transmission. Tractors: MF135, MF150, MF165, MF175, MF230, MF235, MF245, MF255, MF265, MF275, MF285; industrials: 20, 20C, 30, 30B, 30D, 31, 40, 40B, 50C, 50D. 4-speed shift knob. Vintage Iron Hi-lo shift knob. Vintage Iron M2 Spring For Clutch Release Fork & Carrier Spring, clutch release fork to carrier (2) required. Tractors: MF135, MF150, MF165, MF175, MF180, (s/n 9A & up). MF230, MF235, MF240, MF245, MF250, MF253, MF255, MF265, MF270, MF275, MF282, MF283, MF285, MF290, MF298, MF360, MF362, MF375, MF383, MF390, MF393, MF398, MF399, MF670, MF690, MF698, MF699, MF1080 (s/n 9A & up), MF1085. Industrials: 20, 30, 40, 50A, (s/n 9A & up). 20C, 20D, 30B, 30D, 30E, 40B, 40E, 50, 50A, 50C, 50D, 50E, 50F. Forklifts: 4500, M M M M1 Ball type shift lever knob, transmission gearshift lever & planetary shift lever. For all TE, TO, MF models. Vintage Iron Cover, gear shift lever to shift housing. For all TE, TO, MF models. Supersedes M3. Vintage Iron 3-speed shift knob. Can replace plain knob & pattern label M1 & M1. Vintage Iron Rubber gear shift boot. 2-1/16" bottom ID, 11/16" hole diameter. Tractors: MF95, MF97. Vintage Iron MF-4-118

140 4 POWER TRAIN Replacement parts to fit M M M M1 Clutch Discs, Plates, and Springs Spring, piston return, for multi-power transmission, 6 required. Tractors: MF35, MF50, MF65, MF135, MF150, MF165, MF175, MF180, MF235, MF240, MF245, MF255, MF265, MF270, MF275, MF290, MF298, MF375, MF390, MF398. Industrials: 30. Clutch plate, external lugs for multi-power transmission, 3 required. Tractors: MF35, MF50, MF65, MF135, MF150, MF165, MF175, MF180, MF235, MF240, MF245, MF255, MF265, MF270, MF275, MF290, MF298, MF375, MF390, MF398. Industrials: 30. Friction disc, internal teeth, for multi-power transmission & independent PTO. For multi-power, 3 required. Tractors: MF35, MF50, MF65, MF135, MF150, MF165, MF175, MF180, MF235, MF240, MF245, MF255, MF265, MF270, MF275, MF290, MF298, MF375, MF390, MF398. Industrials: 30. For independent PTO, 7 required. Tractors: MF240, MF265 (s/n 9A & up, 2-speed only), MF270, MF275 (s/n 9A & up, 2 speed only), MF290, MF298, MF360, MF375, MF390, MF390T, MF398, MF399, MF670, MF690, MF698, MF699. Industrials: 30E, 40E, 50E. Replaces M1, M1, M1, M1, M1, M1. Clutch plate, external teeth, for independent PTO, 7 required. Tractors: MF240, MF265, (s/n 9A & up, 2-speed only), MF270, MF275 (s/n 9A & up, 2-speed only), MF290, MF298, MF360, MF375, MF390, MF390T, MF398, MF399, MF670, MF690, MF698, MF699. Industrials: 30E, 40E, 50E M M M M M1 Transmission Parts Parts are common to all single & dual clutch, 6-speed & multi-power models: TO35, MF35, MH50, MF65, MF135, MF150, MF165, MF175, MF180, with exceptions noted. Needle bearing kit, for transmission reverse idler gear. Not for shuttle, instant reverse, or 12-speed transmissions, (1) required. Tractors: TO35 (s/n & up), MF35, MH50, MF50, MF65, MF135, MF150, MF165, MF175, MF180, MF230, MF231, MF235, MF240, MF245, MF250, MF253, MF255, MF265, MF270, MF275, MF285, MF290, MF298, MF360, MF375, MF383, MF390 (except 8 speed synchromesh), MF390T, MF1080, MF1085. Industrials: 20, 20C, 30, 31, 40, 40B, 40E, 50C, 50D, 202, 203, 204, 205, 2135, Bearing, needle, for countershaft. For all single and dual clutch, 6-speed and multi-power models. Tractors: TO35, MF35, MH50, MF65, MF135, MF150, MF165, MF175, MF180. Filter screen, transmission. Industrials: 30, 30B, 30D, 40, 40B, 50, 50A, 50C, 50D, 202, 203, 204, 205, 302, 304, Bearing, ball, for main shaft rear & countershaft. For all single and dual clutch, 6-speed and multi-power models. Tractors: TO35, MF35, MH50, MF65, MF135, MF150, MF165, MF175, MF180. Bearing, ball, for PTO drive pinion. For all single and dual clutch, 6-speed and multi-power models. Tractors: TO35, MF35, MH50, MF65, MF135, MF150, MF165. MF-4-119

141 4 POWER TRAIN M M M2 O-ring, 4" I.D. x 5/64" thick. For transmission front PTO pinion shaft & input shaft retainer to housing. For 8-speed & late multi-power. Tractors: MF135, MF150, MF165, MF175, MF180. For all 6-, 8-, 12-speed & multi-power except where noted. Tractors: MF235 (except 6-speed), MF240 (except 6-speed), MF245 (excpet 6-speed), MF250, MF253, MF255, MF265, MF270, MF275, MF282, MF285, MF290, MF298, MF360, MF375, MF383, MF390, MF390T, MF398, MF399, MF670, MF690, MF698, MF699, MF1080, MF1085. For industrials except with instant reverse or where noted: 20 except 6-speed, 20C except 6-speed, 20D, 30 except 6-speed, 30B, 30D, 30E, 31 except 6-speed, 40B, 50A late 8-speed, 50C, 50D, 50E. Bearing, for PTO front drive shaft housing, " O.D. Determine bearing O.D. before ordering. For 6 & 8 speed & multi-power transmission. Tractors: MF135, MF150, MF165, MF175, MF180, MF235, MF240, MF245, MF250, MF253, MF255, MF265, MF270, MF275, MF282, MF283, MF285, MF290, MF298, MF383, MF390, MF398 (also for 12 speed), MF399 (also for 12 speed), MF690, MF699, MF1080, MF1085. Industrials: 20, 20C, 20D, 30, 30B, 30D, 30E, 31, 40B, 40E, 50C, 50D, 50E. Bearing, ball, for PTO shaft. For all single and dual clutch, 6-speed and multi-power models. Tractors: TO35, MF35, MH50, MF65, MF135, MF150, MF M M M M M M1 Oil seal, 1-1/8" I.D. x 1-9/16" O.D., for recess in rear of PTO main drive pinion shaft. For 1500/540 or 1700/540 regular transmission & 6-speed transmission with dual clutch & live PTO (not for manual shuttle or multi-power). Tractors: TO35, MF35, MH50, MF50, MF65, MF135, MF150, MF165, MF175, MF230, MF235, MF245. Industrials: 20, 20C, 30, 31, 35, 202, 203, 2135, Bearing, ball, input drive shaft. For all single and dual clutch, 6-speed and multi-power models. Tractors: TO35, MF35, MH50, MF65, MF135, MF150, MF165, MF175, MF180. Bearing, ball, for countershaft front. Also used for multi-power mainshaft front. Replaces M1. For all single and dual clutch, 6-speed and multi-power models. Tractors: TO35, MF35, MH50, MF65, MF135, MF150, MF165, MF175, MF180. Bearing, needle, for power input pilot, multi-power. For all single and dual clutch, 6-speed and multi-power models. Tractors: TO35, MF35, MH50, MF65, MF135, MF150, MF165, MF175, MF180. Gasket, inspection cover on differential case. Tractors: TE20, TO20, TO30. Gasket, Steering cover transmission. For all single and dual clutch, 6-speed and multi-power models. Tractors: TO35, MF35, MH50, MF65, MF135, MF150, MF165, MF M1 Gasket, transmission housing top differntial case. For all single and dual clutch, 6-speed and multi-power models. Tractors: TO35, MF35, MH50, MF65, MF135, MF150, MF175. MF-4-120

142 4 POWER TRAIN Replacement parts to fit Transmission Friction Disc & Plate For Instant Reverse Clutch M1 Bolts, Nuts & Resin Kit Bolt, 1/2" x 1-45/64' NF, special head, ring gear to case. 12 used M1 Friction disc, 5-1/4" O.D., 45 internal splines,.060" thick. For hydraulic shuttle/instant reverse clutch. Industrials: 30, 30B, 30E, 40, 40B, 50, 50A, 50C, 50D, 50E, 204, 205, 304. Replaces M M M M4 Friction plate, 5-7/16" O.D., 50 external splines. For hydraulic shuttle/instant reverse clutch. Industrials: 30, 30B, 30E, 40, 40B, 50, 50A, 50C, 50D, 50E, 204, 205, 304. Hydraulic Oil Filter Filter element for hydraulic lift pump, top mount. 2-7/16" O.D. 1-29/32" I.D. & 4" long. Tractors: MF35, MF50, MF65, MF85, MF88, MF90, MF1080. Industrials: 202, 203, 204, 205, 302, 304, 2135, 2200, Also the following models with pumps having 10-spline camshaft. Tractors: MF135, MF150, MF165, MF175, MF180. Industrials: 20, 30, 31, 40, 302, 304. Filter, hydraulic oil cooler, multi-power transmission " ID, 1.775" OD, 4.500" length. Tractors: Super 90, MF135, MF165, MF175, MF180, MF1080, MF1100, MF1130. Industrials: 30, 30B, 30E, 40, 50A, 50E, 50F, 204, 205, 302, M M M M1 Nut, 1/2"-20, special hex for M1 bolt. High strength adhesive. Gasket for Planetary Ring Gear Gasket, for outer planetary ring gear on rear axle housing. Tractors: MF65, MF85, MF88, MF90, MF135, MF150, MF165, MF175, MF180, MF235, MF245 (prior to s/n P40085), MF250, MF253, MF255, MF265, MF270, MF275, MF282, MF290, MF360, MF375 (early models), MF383 (early models), MF390 (early models), MF670, MF690 (s/n T & up, 2 wheel drive), MF1080. Industrials: 30, 30B, 30D, 30E, 31, 40, 40B, 40E, 50, 50A, 50C, 50D, 50E, 203, 205, 302, 304, Replaces M2. Differential Rear Drive Coupling Drive coupling, differential, rear. Tractors: TO35, MF50, MF65. Industrials: 202, 204 Work Bull, 203, 205, 356 Tractor shovel, 2200 Treever, 2135 utility. 5" long, 10 splines 1-1/4" & 2" long. MF-4-121

143 4 POWER TRAIN Drive Coupler for Gear and Pinion Set M1 Coupler, 3-13/16" long, rear drive shaft to pinion. Tractors: MF230 (s/n 9A & up). Industrials: 20D. We suggest measuring the pinion spline length & length of coupler to determine if M91 (4-5/16" long) was previously installed & whether M1 coupler is needed. Tractors: TO35 (s/n & up), MF68, MH50, MF50, MF240 (prior to s/n 2773N01001), MF245 std. clearance (s/n 9A & up). Multi-Power Transmission Parts Because of tractor &/or transmission serial numbers, early or late production, it is important to know the tooth & spline count before ordering replacement PTO pinion shaft Application Tractor: MF35 Tractor: MF50 Tractor: MF65 Tractor: MF135 Tractor: MF150 Tractor: MF165 Tractor: MF175 Tractor: MF180 Tractor: MF235 Tractor: MF245 Tractor: MF255 Tractor: MF265 Tractor: MF M3 Seal, For PTO Pinion Shaft Retainer. Multi-Power Trans. 1.58" ID; 1.945" OD M91 Retainer Housing, PTO Pinion Shaft, Multi-Power Trans. Less Bearing & Seal M4 Seal, For PTO Pinion Shaft. Multi-Power Trans. 17 TEETH, 10 SPLINES M92 PTO pinion shaft, for multi-power transmission. 17 teeth, 10 splines. Seal not included. MF-4-122

144 4 POWER TRAIN Replacement parts to fit Rear Axles, Bearings & Related Parts Application TO20, 16 spline TO30, 19 spline TO35, MF35, MF50, early MF135, MF150 using 19 spline end Axle Seal Outer Cup M M M M M M1 Cone M M M1 Axle Collar M M M1 Differential Gear & Pinion Sets, Bearings Axle Seal Inner M M2 Inner Diff. Brg. Cup M M M1 Rear Wheel Bolt M M M2 All kits contain bolts, nuts & resin kit for installation Application Ring Gear & Pinion Set Tractor: TO35 (s/n & up), MF35, MF135 (early production), MF M91 (light duty without lock) Tractor: MF135 (late production), MF235 (with lock) M91 Tractor: MF65, MF165, MF175, MF180, MF235 (Orchard), MF255, MF265, MF275 Industrial Tractor: 20D M91 Tractor: TO35 (s/n & up), MF50, MF240 (to s/n 2773N01001), MF245 (standard clearance, s/n 9A & up), MF230 (s/n 9A & up) Gear & pinion set, 37/6 tooth count. Pinion effective spline length 4-5/16", pinion overall length 10". Used as a service replacement for several original production gear sets. This replacement required using a different drive coupler M1 (3-3/16" long). We suggest measuring the pinion & spline length & length of coupler to determine if M91 was previously installed & whether M1 coupler is needed. Carrier Bearings Cup M M M M1 Carrier Bearings Cone M M M M1 MF-4-123

145 4 POWER TRAIN DTC M A M1 Differential Sleeve Bearings Double tapered cup (53376D) for differential. Tractors: TE20, TO20, TO30, TO35 (prior to s/n ), MF35, MF50 (using sleeve no M91), MF65 (prior to s/n CL ), MF135, MF150, MF165, MF175, MF180. Cone (53177) for differential. Tractors: TO35 (s/n & up), MF50 (using sleeve M92), MF35, MF135, MF150, MF165, MF175, MF180, MF235, MF255, MF265, MF275. Single cup (53375) for differential, two used. Tractors: MF35, MF135, MF150, MF165, MF175, MF180, MF235, MF255, MF265, MF275. Single cup (HM903210) two used, for differential. Tractors: TO35 (s/n & up, using sleeve M93), MF35, MF65 (s/n CL & up), MF165, MF180 (using sleeve M92), MF175, MF235, MF255, MF265, MF M M M M1 Outer oil seal in rear axle housing, for tractors with wet brakes " ID, 3.383" OD,.562" width. Tractors: MF255, MF265 (except orchard), MF275, MF285. MF298, MF398, MF399, MF690 (prior to s/n T ), MF698, MF699, MF1085. Industrials: 30, 30B, 30D, 31, 40, 40B, 50A, 50C, 50D. Gasket, rear axle housing, outer. Tractors: TO20, TO30, TO35. Rear axle or differential carrier plate oil seal. 2" ID, 3.187" OD. Tractors: MF65, MF85, Super 90, MF135 orchard, MF150, MF165, MF175, MF180. Industrials: 30, 40, 50, 203, 205, 302, 304; also MF1080, MF1085, MF235 orchard, MF255, MF275, MF285 with dry brakes. Used as clutch bearing support assembly seal on tractors: MF2675, MF2705, MF2745, MF2775, MF2805. Gasket, rear axle housing, inner. Tractor: TO M M3SK Cone (HM903249), for differential. Tractors: TO35 (s/n & up, using sleeve M93), MF35, MF65 (s/n CL & up), MF165, MF180 (using sleeve M92), MF175, MF235, MF255, MF265, MF275. Rear Axle Gaskets and Seals Rear axle or differential carrier plate oil seal, & speedi-sleeve. Tractors: MF65, MF85, Super 90, MF135 orchard MF150, MF165, MF175, MF180. Industrials: 30, 40, 50, 203, 205, 302, 304, also MF1080, MF1085, MF235 orchard, MF255, MF275, MF285 with dry brakes. Used as clutch bearing support assembly seal. Tractor: MF2675, MF2705, MF2745, MF2775, MF M Gasket, rear axle housing, inner. Tractors: TO30, TO35, MF35, MF50, MF65, MF135, MF150, MF165. Industrials: 20, 20C, 20D, 203, 205, 302, 304. Speedi-Sleeve, 007" thick. Use with M3 seal. Press on to resurface damaged shafts. Speedi-Sleeves are corrosion resistant stainless steel, smoothly finished, & ultra-thin to allow use of original seal, no oversized seal required. Saves money on replacement of shafts. SS92 Sure seal, one pair. Tractor: TO20. MF-4-124

146 4 POWER TRAIN Conversion PTO Assembly Replacement parts to fit Complete assembly replaces & converts M91 from 1-1/8" to 1-3/8" spline. Assembled & ready to install. Includes new 1-3/8" splined PTO shaft, seal, bearing, cover, cap, & bearing retainer ring M1 PTO shaft oil seal. 1-3/4" I.D., 2.685" O.D. Tractors: TO35, MF35, F40, MF50, MF65, MF135, MF150, MF165, MF175, MF PTO conversion assembly to 1-3/8" PTO. Tractors: TE20, TO20, TO /8" PTO Shaft and Components GA1773 PTO shaft ball bearing. Tractors: TE20, TO20, TO PTO shaft only, 1-3/8" 6-spline, converts original M1 from 1-1/8" 6-spline, to 1-3/8" 6-spline. Tractors: TE20, TO20, TO30 (includes retainer sleeve) M1 PTO cap, aluminum alloy replacement. Tractors: TE20, TO20, TO30 all with 1-1/8" or 1-3/8" shafts Retainer sleeve for Tisco , 1-3/8" 6-spline PTO shaft M92 PTO shaft, 1-3/8" dia. 6-spline. Tractors: MF35, TO35, MF50, MF M1 PTO shaft oil seal. 1-5/8" I.D., 2.450" O.D. Tractors: TE20, TO20, TO30. Same as D9NN703BB. MF-4-125

147 4 POWER TRAIN Bearings for PTO Output Shaft M1 Bearing for PTO stub shaft, 540 RPM. Tractors: MF285, MF1085. (88508) M M1 CRK600 Bearing, outer, for PTO output shaft. 45mm ID, 75mm OD, 16mm width. Tractors: TO30, MF35, MH50, MF50, MF65, MF135, MF150, MF165, MF175 (late model), MF235. For models with dry brakes. Tractors: MF255, MF265 (prior to s/n 9A349239), MF275 (to s/n 9A349239). For models using snap rings on bearing. Tractors: MF180, MF230. Industrials: 30, 31, 40 (with dry brakes), 202, 203, 302, 2135, 3165, 20 (with snap ring & bearing). Oil Seal For PTO Output Shaft Oil seal, outer, for PTO output shaft. Tractors: MF230 (axle s/n FD101, CD8028 & up), MF231, MF235 (live PTO with axle s/n FD101 & up), MF240, MF245, MF250, MF253, MF255 (with wet brakes), MF265 (with wet brakes), MF270, MF275, MF282, MF285, MF290, MF298, MF360 (prior to s/n P38370), MF375, MF383, MF390, MF390T, MF398, MF399, MF670, MF690, MF698, MF699, MF1080, MF1085, MF3050, MF3060, MF3070, MF3090. Industrials: 20 (axle s/n FD101, CD8028 & up), 20C, 20D, 30 (with wet brake), 30B, 30D, 30E, 31 (axle s/n FD101, CD8028 & up), 40 (with wet brake), 40B, 40E, 50C, 50D, 50E. Over-Running Couplers Coupler repair kit, services all Hub City over-running couplers. Contains keys, roll pin, set screw, springs, spacer, & retaining ring. MF-4-126

148 5 WHEELS AND ALES Replacement parts to fit Steering Wheel Steering Wheel Cap M M1-OE M M M91 Steering wheel, 17-3/4" diameter, 3/4" hub with 3/16" keyway. Tractors: TE, TO20, TO30, TO35, MF35, MF135, MF50, MF65. Vintage Iron Steering wheel OEM style, 17-3/4" diameter, 3/4" hub with 3/16" keyway, METAL SPOKES. Tractors: TE, TO20, TO30, TO35, MF35, MF135, MF50, MF65. Vintage Iron Steering wheel, 17-3/4" diameter, 5" dish, splined hub. Tractors: MF230 (with power steering, prior to s/n 9A & late production manual), MF235 (with power steering s/n 9A & up, except orchard diesel), MF245 (prior to s/n 9A349239), MF255 (prior to s/n 9A324137), MF265 (prior to s/n 9A349239), MF1500, MF1505, MF1800, MF1805. Industrials: 20C diesel (prior to s/n 9A & early gas with 5" dish), 30B diesel (prior to s/n 9A & all gas), 40B (prior to s/n 9A331974). Combines: 540, 750 (s/n & up), 760 (s/n & up), Replaces M2. Vintage Iron Steering wheel, 3 spoke (uncovered). 15" diameter, 11/16" 3/4" shaft. Tapered, keyed, & stepped hub. Tractors: Massey Harris: Pony, Pacer. Vintage Iron Steering wheel, 3 spoke (covered). 18" diameter, 7/8" 13/16" tapered shaft. Keyed hub. Tractors: 95. Vintage Iron M91 Cap, for steering wheel. Tractors: MF231, MF270, MF283 (except Brazil), MF290, MF298, MF670, MF690, MF698, MF699. Industrials: 50E. For non-telescoping steering column. Tractors: MF4800, MF4840, MF4880, MF4900. Vintage Iron Steering Column Grommet M1 Steering column grommet " length x 3.085" width x 1.480" hole I.D. Tractors: MF35 (s/n & up). Industrials: 202, 203, 204, 205. Vintage Iron M M M M1 Steering Shaft & Bearing Shaft, steering gear. Tractors: TE20, TO20, TO /2" long. Bearing inner cone, use with M1. Roller bearing, use with M1. Bearing cup, steering shaft. Use with M1. Steering Gear Thrust Bearing New design one piece "mono-bearing" replaces conventional bearing cup & cone. Made of a new material called Delrin, similar to nylon used in industrial applications. This new material is self-lubricating & very resistant to wear & shock, resists high temperature & high pressure deformation. Easy-to-follow replacement instructions are included with each bearing. 8N Mono-bearing, for steering shaft on tractors with manual steering. Tractors: TO35, MF35, MF135. Industrials: 35, Replaces M1 (10790Z) cup, & M1 (10790S) cone. 2 required per tractor. 1-3/4" O.D., 7/8" I.D., 7/16" wide. MF-5-127

149 5 WHEELS AND ALES M M1-HD Bushing for Steering Shaft Bushing (metal), for steering shaft, used in front axle support, 2 required. Tractors: MF165 (except LPG), MF175, MF255 (prior to s/n 9A324146), MF265 (prior to s/n 9A324139), MF270, MF275 (prior to s/n 9A324137), MF282, MF283 (except Brazil), MF290, MF670, MF690, MF699. Industrials: 30, 31, Also used in power rack, upper bushing only. Tractors: MF180 (s/n 9A48873 & up), MF1080, MF1100, MF1130, MF1150, MF1155. Row crop & western models. Tractors: MF1085, MF1105, MF1135. Replaces M1, M1. Bushing (Moly type), for steering shaft, used in front axle support, 2 required. Tractors: MF165 (except LPG), MF175, MF255 (prior to s/n 9A324146), MF265 (prior to s/n 9A324139), MF270, MF275 (prior to s/n 9A324137), MF282, MF283 (except Brazil), MF290, MF670, MF690, MF699. Industrials: 30, 31, Also used in power rack, upper bushing only. Tractors: MF180 (s/n 9A48873 & up), MF1080, MF1100, MF1130, MF1150, MF1155. Row crop & western models. Tractors: MF1085, MF1105, MF1135. Replaces M1, M1, M " O.D., 1.900" I.D., 1.675" long M M M92 Power Steering Cylinder and Parts Heavy-duty cylinder comes complete with both ball joint ends and is repairable. Universal design, can be used on left or right side on tractors equipped with 2 cylinders mounted behind front axle. The OEM no longer supplies this part. They replace with individual left hand or right hand cylinders at greater cost. Power steering cylinder, Left hand with two ball joint ends. 12-1/2" long, 5/8" dia. rod, 5.640" stroke. Tractors: MF135 orchard, MF240, MF250. Industrials: 20, 35 utility, 202, 203, 204, 205, 2135, MF20D, MF20E. Replaces M92. Power steering cylinder, Right hand with two ball joint ends. 12-1/2" long, 5/8" dia. rod, 5.640" stroke. Tractors: MF135 orchard, MF240, MF250. Industrials: 20, 35 utility, 202, 203, 204, 205, 2135, MF20D, MF20E. Replaces M92. Cylinder, steering complete (9" long) for hydrostatic or power steering. Tractors: MF240, MF253, MF360, MF362. Industrials: MF20F, MF30E, MF30H, MF40E. Replaces M91. Bushing for Steering Assembly M1 Bushing, main steering arm assembly or power steering cylinder support. Tractors: MF50, MF65, MF135, MF150, MF165, MF175, MF255, MF265, MF270, MF275, MF282, MF285, MF290, MF670, MF690. Industrials: 30, 31, 50F, 50H, 302, 304. (3/4" x 7/8" x 1-1/4") MF-5-128

150 5 WHEELS AND ALES Replacement parts to fit Power Steering Cylinder Ends Power Steering Pumps M FT MT M1 CK34 Ball joint end assembly, for power steering cylinder. Tractors: MF235 orchard diesel, MF245 orchard (with cyl M91, M91, M91 or M91), MF265 (s/n 9A & up with cylinder M91 & M91), MF285 (s/n 9A & up). Industrials: 20C, 30B, 30D (all with cyl M91 & M91), 40, 40B (with cyl M91 & M91), 80 backhoe loader. Forklifts: 2200, Rod end ball joint, with internal threads. For Tisco universal power steering cylinder M92 (sold until 2006). Cylinder head tie rod end, with external threads. For Tisco universal power steering cylinder M92 (sold until 2006). Dust Boot. Universal, 1.200" base x.475" height x.500" hole I.D. Front power steering cylinder ends (will not fit rear cylinder ends). Tractors: TE20, TEA20, TO20, TO30, TO35, MF20, MF35, MF135, MF230, MF235, MF2135, Super 90. Industrials: 202, 203, 205. Vintage Iron Seal Kit For Power Steering Cylinder Seal kit, for power steering cylinders on tractors with 2-cylinder operation. Industrials: 50, 50A, 70 backhoe loader (s/n & up), 356 tractor shovel (s/n & up). Forklift: 2200, Also for original production cylinders M91, M91, M91, M91. Tractors: MF235 orchard, MF245 orchard. Industrials: 20C, 30B, 30D, 40, 40B. Forklift: M M M M92 Power steering pump, straight cut gear, 14 teeth, replaces Parker Hannifin. Tractors: MF285, MF1080, MF1085 (except with hydrostatic p/s pump). Replaces M93. When installing M91 as replacement for M93, MF indicates it is necessary, on some models, to install different lines & fittings. For repairs order seal kit PSP-KIT1. Power steering pump, helical cut gear, 13 teeth, replaces Parker Hannifin. Tractors: MF65 diesel (s/n & up), MF165 diesel, MF255 gas. Industrials: 30 diesel, 40B, 50A, 302 diesel, 304 diesel, 356 diesel, 3165 diesel. Replaces M92 & M91. For repairs order seal kit PSP-KIT1. Power steering pump, helical cut gear, 14 teeth, replaces Parker Hannifin. Tractors: MF165 Perkins gas, MF175, MF255 diesel, MF265 (except with hydrostatic p/s pump), MF275. Industrials: 30 gas, 31, 50C, 50D, 6500 forklift. Replaces M91, M92 & M94. When installing M91 as replacement for M92, M92, or M94, MF indicates it is necessary to install different lines & fittings. For repairs, order seal kit PSP-KIT1. Power steering pump, straight cut gear, 13 teeth, includes drive gear, reservoir & adjustable relief valve preset at 1500 psi. in tractors using Perkins 3 cyl. gas or diesel engines. Tractors: MF35, MF50, MF135, MF150, MF230, MF235, MF245, MF250. Industrials: 20, 20C, 30B, 30D, 30E, 40, 203, 205, 2135, Forklift: 2500, Replaces M91, M92, M91. MF-5-129

151 5 WHEELS AND ALES M92-IMP M M M M M91 Power steering pump, straight cut gear, 13 teeth, includes drive gear, reservoir & adjustable relief preset at 1500 psi. Tractors: MF35, MF50, MF135, MF150, MF230, MF235, MF245, MF250. Industrials: 20, 20C, 30B, 30D, 30E, 40, 203, 205, 2135, Forklift: 2500, Replaces M92, M91, M92, M91, M91. Replaces M92. Power steering pump, helical cut gear, 12 teeth, for tractors with Continental gas engines. Tractors: TO35 (Standard Motors diesel & Cont. gas), MF35, MF50, MH50, MF135, MF150. Industrials: 35, 202, 204, Forklift: Replaces M92, M91, M92, M91, M91. Hydraulic steering/tandem pump. Tractors: MF3050, MF3060, MF3065, MF3070, MF3080, MF3085, MF3090, MF3095, MF3115, MF3120, MF3125, MF6110, MF6120, MF6130, MF6140, MF6150, MF6160, MF6170, MF6180, MF6190, MF6235, MF6245, MF6255, MF6260, MF6265, MF6270, MF6280, MF6290. Replaces M1. Power steering pump. Tractors: MF362, MF365, MF375, MF383, MF390, MF390T. Replaces M92. Steering orbital motor. Tractors: MF240, MF253, MF261, MF263, MF271, MF360, MF362, MF365, MF375, MF383, MF390, MF390T, MF393, MF398, MF399, MF4225, MF4233, MF4240, MF4243, MF4245, MF4253, MF4263, MF4270. Replaces M91. Hydraulic/power steering pump. Tractors: MF399 w/a engine. Replaces M M92 PSP-KIT1 PSP-KIT M M ML Repair & Seal Kits Seal kit, power steering pumps. Tractors: MF270, MF283, MF298, MF670, MF690, MF698. For pump M91 on tractors: MF375, MF383, MF390. For pump M91 on tractor: MF282. For pump M92 on tractor: MF290. Repair kit, power steering pump. Contains seals, o-rings, gaskets, thrust & wear plates. For pumps M91, M91, M91, M91, M91. Seal kit, power steering pump. Contains, seals & gaskets. For pumps M91, M91, M91, M91, M91. Filters for Power Steering Pumps Oil filter element, power steering pump. Tractors: MF253. For Plessey pumps. Industrials: 20 (s/n 9A & up). Forklift: 2500 (late production with Perkins eng.), 4500 (with Perkins diesel). Replaces M1. Oil filter element, power steering pumps. Tractors: MF270, MF282, MF283, MF290, MF298, MF375, MF383, MF390, MF670, MF690, MF698. Also for original Plessy pump # Tractors: MF255, MF265 (prior to s/n 9A349239), MF275 (prior to s/n 9A349239). Industrials: 50C. Power Steering Plate Power steering plate. Mounts under steering wheel nut. 2-1/2" O.D., 5/8" center hole with keyway. Anodized red aluminum. Tractors: MF35, MF65, MF85, MF88, Super 90. Industrials: 202, 203, 204, 205, 303, 404. Vintage Iron MF-5-130

152 5 WHEELS AND ALES Replacement parts to fit Run Tee Used with power steering lines. Axle Lock Bolt Secures axle extension to axle assembly. Our bolt is 1/2" longer to accommodate front bumper M M M M2 Run tee for power steering lines, 37 JIC, adjustable O.R.B., threads 9/16"- 18 for 3/8" O.D. tube. Used on a wide range of ag & industrial tractors primarily with the power steering lines. Front Axle Pivot Pin Pivot pin for swept back axles. 1-3/4" O.D., 4-3/4" long. Has 7/8" dia. bolt hole & 1" dia. crank hole. Tractors: TO20, TO30, TO35, MF35, MF135 (prior to s/n 9A86902). Industrials: 20 (prior to s/n 9A86902), 2135 turf & narrow. Replaces M1. Use with flanged axle bushing M1. Axle Support Bushings Front pivot support bushing. Tractors: TE20, TO20, TO30, TO /16" O.D., 1-25/32" I.D., 1-1/2" long. Front pivot support bushing, flanged. For swept back axles. Tractors: TE20, TO20, TO30, TO35, MF35, MF135, MF235. Industrial: 20, " O.D., 1.750",.820" long. Bushing front axle support pivot pin. For straight adjustable axles. Tractors: MF135 vineyard, MF235, MF245 vineyard. Replaces M M1-L M M M91 Lock bolt for adjustable front axles. Tractors: F40, MH50, MF50, MF65, MF150, MF175, MF230 (s/n 9A & up), MF245 semi-swept, MF255, MF265, MF275. Industrials: 20C, 30, 31, 3165 turf. Can replace M1. Usable length 3-3/4", 5-1/8" overall, 3/4"-16 thread. Hex nut, 3/4" SAE, for lock bolt M1 for adjustable front axles. Tractors: F40, MH50, MF50, MF65, MF150, MF175, MF230 (s/n 9A & up), MF245 semi-swept, MF255, MF265, MF275. Industrials: 20C, 30, 31, 3165 turf. Front Axle Drag Link Ends Length shown is from end of shaft/tube to center of post/ball stud. Drag link end assembly, front, 3.250" to center of post,.687"-18 right hand thread. Tractors: TO20, TO30, TO35, MF35. Drag link end assembly, rear, 3.594" to center of post,.687"-18 left hand thread. Tractors: TO20, TO30, TO35, MF35. Drag link end assembly, front. 3.75" to center of post,.812"-16 right hand thread. For drag links with adjustable end. Tractors: F40, MH50, MF50, MF65, MF135 orchard, MF150, MF165, MF175. Industrials: 20, 35 utility, 202, 203, 204, 205, 356 tractor shovel, 2135 utility, M92 Drag link end, rear, threaded. 3" to center of post. Tractors: MF135, MF240, MF250. Industrials: 20D with adjustable axle, 2135 narrow axle. Replaces M1. MF-5-131

153 5 WHEELS AND ALES Front Axle Tie Rod Parts With adjustable front axle *Length shown is fron end of shaft/tube to center of post/ball stud M91 Inner tie rod end, right hand, adjustable. 6" to center of post,.812"-16 right hand thread. For hi & lo clearance tractors. Tractors: MF50 & MH50 (prior to s/n ), MF65 (gas, prior to s/n ), MF65 (diesel, prior to s/n ) M91 Outer right hand tie rod end for hi & lo clearance tractors, " to center of post,.737" O.D. Tractors: MF50 & MH50 (prior to s/n ), MF65 (gas, prior to s/n ), MF65 (diesel, prior to s/n ). Replaces M M92 Inner tie rod end, right hand, adjustable. 6.50" to center of post,.812"-16 right hand thread. For hi & lo clearance models. Tractors: MF50 (s/n to ), MF65 (gas, s/n to ), MF65 (diesel, s/n to ) M91 Outer left hand tie rod end for hi & lo clearance tractors, " to center of post,.737" O.D. Tractors: MF50 & MH50 (prior to s/n ), MF65 (gas, prior to s/n ), MF65 (diesel, prior to s/n ). Replaces M M91 Tie rod end, left hand or right hand, outer. 15" to center of post,.742" O.D. Notched, adjustable, for front axle. Tractors: MF165 (except LP), MF175, MF255, MF265 (except Orchard), MF275. Industrials: 30 Turf, 3165 Turf M91 Tie rod tube, right hand, for hi & lo clearance tractors, overall length ". Tractors: MF50 & MH50 (prior to s/n ), MF65 (gas, prior to s/n ), MF65 (diesel, prior to s/n ) M91 Tie rod tube with end, right hand, inner, includes clamp " to center of post,.75" I.D. For adjustable front axle. Tractors: MF165 (except LP), MF175, MF255, MF265 (except Orchard), MF275. Industrials: 30 Turf, 3165 Turf M91 Inner tie rod, left hand for hi & lo clearance tractors, overall length 15.25". Tractors: MF50 (s/n to ), MF65 (gas, s/n to ), MF65 (diesel, s/n to ) M1 Tie rod end, left hand, inner " to center of post, 1" O.D., female thread. For adjustable front axle. Tractors: MF165 (except LP), MF175, MF255, MF265, MF275. Industrials: 30, 31, 3165 Turf. MF-5-132

154 5 WHEELS AND ALES Replacement parts to fit M91 Tie rod tube with clamp, LH, 13-3/8" overall length. For adjustable front axles. Tractors: MF165 (except LP), MF175, MF255, MF265 (except Orchard), MF275. Industrials: 30 Turf, 3165 Turf M91 Tie rod end, left hand, slotted, " to center of post,.937" O.D., includes boot & grease fitting. For semi-swept adjustable axle. Tractors: MF230 (s/n 9A & up), MF245 (including vine & narrow orchard). Industrials: 20C Turf M92 Tie rod end, outer left hand or right hand, slotted " to center of post,.937" O.D. For adjustable front axle. Tractors: MF180, MF1080, MF M92 Tie rod end, threaded, includes boot & grease fitting " to center of post, 1"-16 right hand threads,.705" small part of taper. For semi-swept adjustable axle. Tractors: MF230 (s/n 9A & up), MF245 (including vine & narrow orchard). Industrials: 20C Turf M91 Tie rod tube with clamp, for left hand or right hand " overall length, 1"-16 female thread. For adjustable front axle. Tractors: MF180, MF1080, MF M92 Tie rod end, outer, LH or RH, recess for set screw (7). 14-3/4" to center of post. For adjustable front axle. Tractors: MF270, MF282, MF283 (except Brazil), MF670, MF M92 Tie rod end, inner, left hand or right hand, 3.875" to center of post, 1"-16 right hand thread. For adjustable front axle. Tractors: MF180, MF1080, MF M91 Tie rod end inner, right hand, slotted, 15.5" to center of post,.937" O.D. Tractors: MF285 (with adjustable front axle) M91 Tie rod center tube with clamp, bolt, nut & lock washer. 33" overall length, 1"-16 female thread. For semi-swept adjustable axle. Tractors: MF230 (s/n 9A & up), MF245 (except vine & orchard). Industrials: 20C Turf. MF-5-133

155 5 WHEELS AND ALES M92 Tie rod end outer, right hand, 5.03" to center of post, 1"-16 right hand thread. Tractors: MF285 (with adjustable front axle) M91 Tie rod end, inner, left hand or right hand. 4" to center of post, 1"-16 right hand thread. For adjustable or fixed front axle. Tractors: MF1100, MF1105, MF1130, MF1135, MF1150, MF M91 Tie rod tube, RH, includes set screw & lock nut. 17-3/4" overall length. For adjustable front axle. Tractors: MF270, MF282, MF283 (except Brazil), MF670, MF M91 Tie rod end, threaded, 5" to center of post. For fixed & adjustable front axles. Tractors: MF2675, MF M91 Tie rod end with socket & clamp, inner, left hand, 17" to center of post. Tractors: MF285 (with adjustable front axle). UTRB Universal tie rod boot " base x.965" height x.500" hole I.D. Vintage Iron M91 Tie rod end outer, left hand, slotted. 15.5" to center of post,.937" O.D. Tractors: MF285 (with adjustable front axle) R1 Tie Rod Boot. Base 1.450" x Height.600" x Hole ID.550". Vintage Iron Steering Arms M93 Tie rod end, slotted, left hand or right hand " to center of post,.937" O.D. For adjustable front axle. Tractors: MF1100, MF1105, MF1130, MF1135, MF1150, MF M M1 Steering arm. Left hand arm. Tractors: MF165, MF175, MF255, MF265, MF275, MF285. Industrials: MF630, MF31, MF3165. Steering arm. Right hand arm. Tractors: MF165, MF175, MF255, MF265, MF275, MF285. Industrials: MF630, MF31, MF3165. MF-5-134

156 5 WHEELS AND ALES Replacement parts to fit Spindle Assemblies M96 Spindle assembly, Right hand. (Vertical shaft 11.00"). Tractors: MF175 UK M96 Spindle assembly, Left hand. (Vertical shaft 11.00"). Tractors: MF175 UK M91 Spindle assembly, Right hand (used with 348mm axles). (Vertical shaft "). Tractors: MF375, MF390, MF390T, MF393, MF396, MF398, MF M94 Spindle assembly, Right hand. (Vertical shaft " x 1.245" dia). Tractors: MF35 UK (s/n & up), MF135 UK, MF M91 Spindle assembly, Left hand (used with 348mm axles). (Vertical shaft "). Tractors: MF375, MF390, MF390T, MF393, MF396, MF398, MF399. Front Axle Knees M94 Spindle assembly, Left hand. (Vertical shaft " x 1.245" dia). Tractors: MF35 UK (s/n & up), MF135 UK, MF M92 Spindle, LH, or RH, for standard adjustable axles. Vertical shaft, 12-7/16" x 1.492". Not for row crop wide, orchard or lo-profile. Tractors: MF165 (except LPG), MF175, MF255 (to s/n 9A324146), MF265 (to s/n 9A324139), MF275 (to s/n 9A324137) M92 Front axle knee, Right hand, HD. (Vertical height 8.750"). Tractors: MF135 UK (s/n & up), MF235 (std straight axle), MF M M95 Spindle assembly, Right hand. (Vertical shaft " x 1.50" dia). Tractors: MF165 UK high clearance (to s/n ), MF255 row crop (export, to s/n 9A282625), MF270 std, MF282, MF283 std clearance, MF290 std clearance. Spindle assembly, Left hand. (Vertical shaft " x 1.50" dia). Tractors: MF165 UK high clearance (to s/n ), MF255 row crop (export, to s/n 9A282625), MF270 std, MF282, MF283 std clearance, MF290 std clearance M92 Front axle knee, Left hand, HD. (Vertical height 8.750"). Tractors: MF135 UK (s/n & up), MF235 (std straight axle), MF M M95 Spindle assembly, Right hand. (Vertical shaft 10.00" x 1.50" dia). Tractors: MF165 (UK HD & South Africa), MF255 std (export), MF270 lo-clearance, MF290. Spindle assembly, Left hand. (Vertical shaft 10.00" x 1.50" dia). Tractors: MF165 (UK HD & South Africa), MF255 std (export), MF270 lo-clearance, MF M91 Front axle knee, Right or Left hand, HD. (Vertical height "). Tractors: MF165 UK (to engine s/n ), MF175 UK (s/n & up), MF178 (s/n & up), MF255 (to s/n 9A282265), MF270, MF282, MF283 (std clearance), MF290 (std clearance) M94 Spindle assembly, Right hand. (Vertical shaft " x 1.50" dia). Tractors: MF165 UK, MF240, MF250. Industrials: MF20D, MF20E M94 Spindle assembly, Left hand. (Vertical shaft " x 1.50" dia). Tractors: MF165 UK, MF240, MF250. Industrials: MF20D, MF20E M91 Front axle knee, Right or Left hand. (Vertical height 7.625"). Tractors: MF165, MF255 (std), MF270 (low clearance), MF290 (low clearance). MF-5-135

157 5 WHEELS AND ALES Front Spindles, Bearings and Axle Parts Application Tractor: TE20, TO20, TO30, TO35, MF35, FE35 (Right Hand) Tractor: TE20, TO20, TO30, TO35, MF35, FE35 (Left Hand) Industrial Tractor: 40 Tractor: MF65, MF50 (Right Hand) Industrial Tractor: 40 Tractor: MF65, MF50 (Left Hand) Tractor: MF135, MF235 Tractor: MF150, MF165, MF175, MF180, MF245, MF255, MF265, MF275, MF1080 Tractor: MF85, MF90, Super 90 Tractor: MF1100, MF1130, MF1105, MF1135, MF1150 Industrial Tractor: 30 Tractor: MF255, MF265, MF275, MF285, MF1085 Spindle (A) Bushing (B) M M M M M M M M M M Thrust Seal and Bearing Wear (C) Sleeve (D) M M M M M M M M M M M M1 Inner Cone (E) BR BR BR BR M1 LM M1 LM M M M1 Inner Cup (F) M M M M M1 LM M1 LM M Outer Cone (H) M M M M M1 LM M1 LM LM LM67048 Outer Cup (G) M M M M M1 LM11910 LM LM LM67010 Bearing Kit (J) M M M M M M92 FW M91 FW86 MF-5-136

158 5 WHEELS AND ALES Replacement parts to fit Special Spindle Thrust Bearing Front Axle Spindle Bushings M1 Spindle bushing. Tractors: TE20, TO20, TO30, TO35, FE35, MF35, MF135 (deluxe, special, and vine with swept back axle), MF235 (except orchard, & vine). Industrials: 20 turf, 2135 (except turf) " O.D., 1.240" I.D., 1.500" long M91-SP M1 Replaces OEM ball bearing unit Special spindle thrust bearing made of molybdenum disulfide impregnated nylon made to outlast original ball-type bearing by as much as three to one Designed for use where severe applications require both high friction and heavy load wear resistance Spindle thrust bearing. Tractors: MF65 Utility, MF50 Multi purpose, MF135 Orchard only, MF165 South Africa, MF175 Minute Maid Corp, MF230 Semi swept axle, MF235 Diesel (Gas s/n 9A & up), MF245 (standard-vine-narrow orchard semi swept Orchard, no adju.), 202, 203, 204, 205, 2135 utility (with solid axle), 3165 utility (with solid axle), 2200 tractor, 4500 forklift, 20 industrial (with solid axle), 30 industrial (with solid axle), 40 industrial and navy (with solid axle), 31 industrial, 20C industrial (with solid axle), 30B industrial, 40B industiral (prior to s/n 9A326404). Spindle thrust bearing. 1-1/4" I.D., 2-3/16" O.D., 5/8" deep. Tractors: MF35 (dual slot spindle), TE20, TO20, TO30, TO35, MF35, FE35, F40, MF50, MF65 (low and hi clearance), MF135 (deluxe and standard), MF235 Vine (with either swept or straight axle), MF235 (standard swept axle), MF245 Vine (with straight axle), MF230 (with swept axle), 2135 Turf (narrow vine), 20 Industrial (turf adjustable), MF150 (Standard and Row), MF165 (row crop LPG). Thrust bearing, front axle spindle " I.D., 2.875" O.D.,.787" deep. Industrials: 40B (s/n 9A & up), 50, 50A, 50C, 50D, 50E, 302, 304. Forklifts: 2500, 6500, 6500H M M1-HD Spindle bushing. Tractors: F40, MH50 (except multi-purpose), MF50, MF65 (except utility), MF150 (prior to s/n 9A with swept back axle), MF165LPG " O.D., 1.240" I.D., 1.500" long. Special Moly bushings replace steel OEM part. Moly bushings have superior wear tolerance, self-lubricating, no machining. Spindle bushing (Moly type). Tractors: MH50 multi-purpose, MF65 utility, MF85, MF88, Super MF90, MF135 orchard, MF150 (s/n 9A & up with semi-swept axle), MF165 (except LPG), MF175, MF180, MF230 (s/n 9A & up with semi-swept back axle), MF235 orchard, MF245 (except vineyard), MF255, MF265, MF275, MF285, MF1080, MF1085. Industrials: 20 (except turf), 20C, 30 turf, 30B, 30D, 35 utility, 40, 40B (prior to s/n 9A326404), 202, 204, 205, 405, 302 (prior to s/n ), 304 (prior to s/n ), 2135 utility, 3165 turf. Forklift: " O.D., 1.500" I.D., 1.500" long. MF-5-137

159 5 WHEELS AND ALES Dust Seal For Front Axle Spindle Wheel Bearing Kits M2 LN10-2 LN M1 Dust seal, felt, 1-15/32" I.D. x 2-9/64" O.D. x 1/4" wide. For top of front axle spindle. Tractors: MH50 (fixed axle), MF65 (fixed axle), MF85, MF88, MF90, MF135 (fixed axle), MF165 (except LPG), MF175, MF180, MF230 (except swept back axle), MF231, MF235 orchard, MF240 (prior to s/n 2773N01001), MF245 (except vineyard with fixed axle), MF250, MF253, MF255, MF265, MF270, MF275, MF282, MF283, MF285, MF290, MF360, MF670, MF690, MF1080, MF1085. Industrials: 20 (fixed axle), 20C, 20D, 30, 30B, 30D, 30E, 31, 35 utility, 40, 40B, 40E, 200 (fixed axle), 302 (prior to s/n ), 304 (prior to s/n ), 2135 utility, Wheel Clamp Lock Nut No re-threading necessary on worn shafts. Directions: put on inside sleeve nut (A) & adjust to suit bearing; hold with wrench in position while screwing on outside ring nut (B) tightly. Picture (C) shows the lock nut complete. 3/4" /8" - 14 Front Axle Grease Seal For Hub Front axle hub seal " I.D., 3.374" O.D. Tractors: MF250 (with 6.00 x 10 rim), MF253 (with 179mm high axle), MF270, MF282, MF283 (except Brazil), MF290, MF298, MF360, MF375, MF383, MF390, MF398, MF399, MF670, MF690, MF698, MF699. Industrials: 20D (with fixed axle), 30E, 40E M92 FW M M1WF Wheel bearing kit, for front wheel using 5-1/2" wide hub M91. Tractors: MF135, MF150, MF165, MF175, MF180, MF230, MF235 (except vine & orchard), MF245 (except vine & orchard), MF255 (prior to s/n 9A324145), MF265 (prior to s/n 9A324138), MF275 (prior to s/n 9A324136), MF1080, MF1085 (all tricycle and early production with hub using 9/16" national fine wheel bolts, not for fixed or adjustable axle). Industrials: 20, 20C turf, 30 turf, 2135 (s/n & up, using 6-hole hub, except narrow). Wheel bearing kit, for front wheels using 5-1/4" wide hub M91. Tractors: MF225 (s/n 9A & up), MF265 (s/n 9A & up), MF275 (s/n 9A & up), MF285, MF1085 (late production with fixed or adjustable axle). Not for tricycle axle or hub using 9/16" national fine wheel bolts. Industrial: 30 (except turf). Front Hub Caps Hub cap, front wheel, threaded O.D. 3" for front hubs with threaded recess. Tractors: MF135, MF150, MF165, MF175, MF180, MF235, MF255, MF265, MF275, MF1000, MF1080, MF1085, MF1105, MF1130, MF1135. Industrials: 20, 30, 2135, Hub cap, front wheel, threaded O.D. 2-3/4", with grease fitting. For front hubs with threaded recess. Tractors: MF250 (with split rim 6.00 x 10), MF253 (with 179mm high axle), MF270, MF282, MF283 (except Brazil), MF290, MF360, MF375, MF383, MF390, MF398, MF399, MF670, MF690. Industrials: 20D (fixed axle), 30E, 40E. MF-5-138

160 5 WHEELS AND ALES Replacement parts to fit Wheel Hub Assembly Front Wheel & Wheel Bolts M91 Hub assembly, front wheel, 6-hole with cups (LM11910 & LM48510) & wear sleeves. Tractors: MF135, MF165, MF175, MF180, MF230, MF235 (except vineyard & orchard), MF245 (except vineyard & orchard), MF255 (prior to s/n 9A324145), MF265 (prior to s/n 9A324138), MF275 (prior to s/n 9A324136), MF1080, MF1085 (early production with 5-1/2" wide hub). Industrials: 20, 20C turf, 30 turf, 2135 (s/n & up, s/n 9A50318 & up), using 6-hole hub, except narrow). Replaces hubs M91, M91, & M93. Order M1 hub bolts when replacing older hubs with new hub M M M M M1 Front wheel, with weight holes. 4:50 x 16, 6-bolt, 6" bolt circle with 4.62 pilot for 5:50 or 6:00 x 16 tires lb. capacity. Same as TW450. Front wheel, with weight holes. 5.50" x 16", 6-bolt 6" bolt circle with 4.62" pilot for 7.50" x 16" tires lb. capacity. Same as TW550. Front wheel, 8" x 16" 6-bolt, 6" bolt circle with 4.62 pilot. For rear wheel applications. Combines: 410, 510, 540, 550, 750. Hub bolts, front wheel, tapered, 9/16" x 1" threads, 1-9/16" total length M M M M92 Hub assembly, front wheel, 6-hole. For models with standard duty axles. Tractors: MF165, MF250, MF255, MF270, MF290, MF362, MF670, MF690. For models with heavy duty axles. Tractors: MF283, MF360, MF375, MF383, MF390, MF390T, MF393, MF398, MF399. Industrials: 20D, 20F, 30E, 30H, 40E. * Does not contain cups or cones Hub bolts, front wheel, tapered, 9/16" x 1" threads, 1-9/16" total length. Wear sleeve, front wheel hub, for M91. Hub, front wheel. Tractors: MF255, MF265, MF275, MF M M M1 Bolt, front wheel, tapered, 1/2" x 1" NF threads. For tractors: MF231, MF240, MF250 except Lo-profile, MF253; industrials: 20D turf or adjustable axle. Replaces M1. Stud, hub, front wheel, 1/2" x 1-3/8" NF. Tractors: TE20, TO20, TO30, MF30, TO35, MF35, MH50, MF50, MF135, MF150, MF165, MF175, MF180, MF1080, MF1085. Stud, hub, front wheel, 1/2" x 1-1/2" NF, for 6-hole non-threaded front wheel hub. Tractors: MF65 utility, MF85, MF Super 90, MF250 (Lo-profile with 15" wheels), MF253 (with 179mm high axle), MF270, MF282, MF283, MF290, MF360, MF375, MF383, MF390, MF398, MF399, MF670, MF690, MF1100, MF1130. Industrials: 20D (except turf with fixed axle), 35 turf, 40E. Use with nut M M1 Nut, front wheel, 1/2" NF for front wheel stud M1, M1. MF-5-139

161 5 WHEELS AND ALES MF-FWL-1 Bolt Kit Bolt, front wheel bolt lug kit. Contains 6 special long 4140 chrome-moly heat treated bolts & 6 special heavy-duty 45 tapered shoulder nuts. Will not vibrate loose as originals do. Used on most MF tractors. Rear Wheel Rims and Bolts M91 Power Adjust Rims, Clamp and Attaching Parts Power adjust rim, 10 x 28, 4 rail type. For double ramp clamp, holes in rail for stop body screw are drilled parallel to axle (not at angle). Use with stop body M1, stop body screw M1, clamp M1, M M M M M M M M M1 Rim, 10 x 28 demountable rim with 6 loop clamps. Painted aluminum. Rim, 11 x 28 demountable rim with 6 loop clamps. Painted aluminum. Rim, 12 x 24 demountable rim for 13 x 24 or 14 x 24 tires, with 6 loop clamps. Bolt, 5/8" x 2-7/8" NF, for rear wheel disc to rim. Tractors: MF25, MF130, MF240, MF250, MF2640, MF3630, MF3650. Industrials: 20D, 30E. Use with nut Nut, 5/8"-18" x 1-1/16", use with rear wheel bolt M1. Stud, rear wheel. Tractors: TO20, TO30, TO35, MF35 std., MF50, MF135 vineyard, MF150 std., MF235 std. & vineyard, MF245 std. & vineyard. 9/16" x 2" NF. Nut, rear wheel stud. 9/16" NF. Used with M1 & M2 stud. Stud, rear wheel. 5/8"-18 thread, 2.150" long. Tractors: MF35 & MF135 orchard, MF150 (row crop with planetary), MF235, MF245 orchard, MF255, MF265, MF275, MF165, MF175, MF180 (with wet or dry brakes). 5/8"-18 thread, 2.150" length. Nut, rear wheel. 5/8"-18 thread. For MF65 only M M M1 Stop body, for power adjust rims M91, M91, & M91. Use with double ramp clamp M1 or M2. Replaces M1. Screw, for stop body M1. Use with power adjust rims M91, M91 & M91. Clamp, disc to rim. Double ramp type for power adjust rims M91, M91, & M91. For use on a wide range models. Tractors: TO35, MF35, MH50, MF50, MF65, MF90, MF135, MF150, MF165, MF175, MF180, MF184-4, MF230, MF235, MF240, MF245, MF250, MF253, MF255, MF265, MF275, MF282, MF285, MF360, MF362, MF375, MF390, MF390T, MF398, MF399, MF698, MF1080, MF1085, MF1100, MF1105, MF1130, MF1150, MF1155, MF1500, MF1505, MF1800, MF2675, MF2705, MF2745, MF2775, MF2805, MF4800, MF4840. Industrials: 30, 31, 40B. Replaces M1, M2. MF-5-140

162 6 HITCH AND HYDRAULICS Replacement parts to fit HLBMF61 HLBMF62 HLBMF M M2 Leveling Box Assembly And Related Parts Leveling Box Assembly, standard right hand, category I, 20-1/2" closed, 26" open. Contains fork, shaft, pinion (185220M1-10-1/2"), housing, gear, bearing, handle & hardware. Replaces Services all catergory I standard models. Leveling box assembly, right hand. 23" closed, 27" open. Includes 14-5/8" shaft & pinion M1 & fork M1. For high clearance models. Tractors: MF50, MF65, MF150, MF165. Leveling box assembly, right hand. 21" closed, 25" open. Includes 12-9/32" shaft & pinion M2 & fork M1. For low clearance models. Tractors: MF50, MF65, MF150, MF165. Leveling box assembly, Standard clearance, Cat II. 19" closed, 24-1/2" open. Contains fork, shaft, pinion, housing, gear, bearing, handle & hardware. Tractors: MF165, MF240. Industrials: MF20D Pinion gear, leveling box. Tractors: TE, TO, & MF prior to M E-HD M M M2 Heavy-duty leveling box assembly, right hand. 1" shaft & pinion 14-3/4" long. Tractors: MF65, MF165, MF175, MF265. Extra heavy-duty leveling box assembly, right hand. 1" shaft & pinion 14-3/4" long. Tractors: MF65, MF165, MF175, MF265. Fork, leveling box, heavy-duty, 12-3/4" long, for 1" shaft. Use with heavy-duty leveling box M95. Tractors: MF65, MF165, MF175, MF265. Fork, leveling box, extra heavy-duty, 16-1/2" long, for 1" shaft. Used with extra heavy-duty leveling box E-HD. Tractors: MF65, MF165, MF175, MF265. Fork can also be used on tractors: MF185, MF275, MF283, MF285, MF375, MF383. Shaft & pinion, leveling box, 14-3/4" long, 1" shaft. For heavy-duty & extra heavy-duty leveling boxes M1 & EHD. Tractors: MF65, MF165, MF175, MF265. Left Hand Leveling Rod M1 Thrust bearing, pinion shaft in leveling box M1 Knuckle, leveling box to lift arm. Tractors: TE, TO, & MF models using 3/4" offset M92 Lift link, left hand, non-adjustable. Hole centers 19-13/16". Tractors: TO35, MF35, F40, MH50, MF50, MF135, MF150. Industrials: 202, 204, 2135, M M1 Pin, knuckle to leveling box & knuckle to arm; 5/8" x 3". Crank handle, for leveling box assembly M1-HD Lift link, left hand, non-adjustable, heavy-duty. Hole centers 23-1/4", 24-1/4", 25-1/4". Tractors: MF135, MF150, MF230, MF235, MF245. Industrials: 20, 20C, 30, 202, 204, 2135, Replaces M1. MF-6-141

163 6 HITCH AND HYDRAULICS Left Hand Rod And Yoke Assembly Lower Forks M1 Fork, leveling box, 10-1/4" long, 3/4" NC thread. Tractors: TE20, TO20, TO30, TO35 (when used with 14" shaft) M M91 Left hand rod & yoke assembly, 3/4" thread, 4-1/8" thread length, 14-7/8" long. Tractors: MF65, MF165, MF235 orchard, MF245 orchard, MF265, MF275 (low-profile with 16" rims). Left hand rod & yoke assembly, 1" thread, 4-1/4" thread length, 16-1/4" long. Tractors: MF150, MF175, MF180, MF265 (std. with 24" rims). Shafts With Leveling Gear M1 Fork, leveling box, 1-1/2" across fork, 14-1/2" long, 3/4" NC thread. Tractors: TE20, TO20, TO30, MF35, MF135, MF150, MF65 (used in standard right hand assembly with 10-1/2" shaft), also left hand on MF65, MF230, MF231, MF235, MF240, MF245, MF250. Industrials: 20, 20C, 20D, 30E, 40E, 202, 204, 2135 (late production turf and utility), Also left hand fork on tractors: MF231, MF240, MF250; industrials: 20D, 30E, 40E. Lift Shaft Bushings M M M2 Shaft & pinion, leveling box, 10-1/2" long, 3/4" NC thread. Tractors: TE20, TO20, TO30, MF35, MF135 (Used in standard RH assy. with 14-1/2" yoke). Shaft & pinion, leveling box, 14-5/8" long, 3/4" NC thread. Tractors: MF65 (hi-clearance), MF150 row crop, MF165 row crop. Industrials: 30, 40. Shaft & pinion, leveling box, 12-9/32" long, 3/4" NC thread. Tractors: MF65, MF235, MF245, MF M M1 Bushing, hydraulic lift shaft; 2-3/8" O.D., 2" I.D., 3" long. Tractors: TE20, TO20, TO30. Bushing, hydraulic lift shaft. 2.36"O.D., 1.97"I.D., 1.39" long. Tractors: TO35, MF35, MF50, MF65, MF135, MF150, MF165. For shaft M2, 4 required. Shaft M3 uses bushing M1, not supplied by Tisco. Hydraulic Lift Parts Hydraulic Lift Arms M M91 Arm, hydraulic lift, right or left, 51-splines. Tractors: MF135, MF175, MF235, MF230, MF245. Industrials: 202, 203, 204, 205, 302, 304, 2135, 3165, 2200, 30, 20, 40, 40B 40C. Replaces M1. Lower lift arm assembly. Category II. Tractors: MF135 (s/n & up), MF240. Industrials: MF20D. Right or Left. 36" hole centers M M3 Shaft, hydraulic lift, 37 splined end. Tractors: TO35, MF35, MF50. Early production tractors: MF135, MF150, MF165. Industrials: 35 turf, 2135 utility. Shaft, hydraulic lift, 51-splined end. Tractors: MF135, MF150, MF165 (late production). MF-6-142

164 6 HITCH AND HYDRAULICS Replacement parts to fit Hydraulic Lift Cover Gasket Set Hydraulic Lift Cylinder & Piston M1 Cylinder, hydraulic lift, for 2-1/2" dia. piston. Tractors: TE20, TO20, TO30. Replaces M1. LCRK M M M M M M3 9N M M1 Gasket kit, lift cover repair. Tractors: TE20, TO20, TO30. Individual Gaskets Gasket, hydraulic lift cover. Tractors: TE20, TE-A20, TO20, TO30. Disc gasket for quadrant lever friction plate. 3" O.D., 9/16" I.D.,.175" thick. Tractors: TO20, TO30. Gasket, hydraulic lift cover to quadrant. Tractors: TO20, TO30. Gasket, pump base. Tractors: TE20, TO20, TO30. Gasket, valve chamber. Tractors: TE20, TO20, TO30. Gasket, inspection cover on differential case. Tractors: TE20, TO20, TO30. Gasket, hydraulic lift cylinder housing. Tractors: TE20, TE-A20, TO20, TO30. Gasket, hydraulic lift cover. Tractors: TO35, MF35, F40, MH50, MF50, MF65, MF150, MF165, MF175, MF180, MF230, MF235, MF245, MF255, MF265, MF275. Industrials: 20, 20C, 30, 30B, 30D, 31, 40, 40B, 50A, 50C. Gasket, pump base drain plug, also transmission filler plug. Tractors: TO20, TO M M M M M M M91 Piston, hydraulic lift, less rings. 2-1/2" dia. Tractors: TE20, TO20, TO30, TO35 (prior to s/n ), F40, MH50. Piston rings, hydraulic lift, 3 required, for 2-1/2" dia. piston. Tractors: TE20, TO20, TO30, TO35 (prior to s/n ), F40, MF50. Piston, hydraulic lift, includes rings, 3" dia. Tractors: TO35 (s/n & up), MF35, MF50, MF65. For early production tractors: MF135, MF150, MF165 using 3" dia. piston. Piston ring kit, 3" dia. 3 rings for M91 piston, hydraulic lift. Tractors: TO35 (s/n & up), MF35, MF50, MF65. For early production tractors: MF135, MF150, MF165 using 3" dia. piston. Piston Rings, for 3-1/8" dia. hydraulic lift piston M91, 3 required. These rings will not work on new style piston M91. Cylinder, hydraulic lift for 3-1/8" dia. piston. Tractors: MF135, MF150, MF165, MF230, MF235, MF240, MF245, MF250, MF282. Industrials: 20, 20C, 20D, 30, 30E, , 203, 204, 205, 302, 304, 2135, Use with M91 piston with rings. Piston, with rings, hydraulic lift, 3-1/8" dia. Tractors: MF135, MF150, MF165, MF230, MF235, MF240, MF245, MF250, MF255, MF265, MF282. Industrials: 20, 20C, 20D, 30, 30E, 40, 202, 203, 204, 205, 302, 304, 2135, Replaces M91. MF-6-143

165 6 HITCH AND HYDRAULICS Quadrant Stop Kit Lift Arm Ends-Various Models QSK3FF Quadrant stop kit, includes wing nut and flat washer. Tractors: TE20, TO20, TO30. Economy Lower Lift Arms M92 Lift arm end, category I, left hand, 7/8" pin hole M91 Lower lift arm, universal, less pin & chain. Tractors: TE20, TO20, TO30. Right or left. 32" hole centers. Forged Lower Lift Arm Assemblies M92 SBA M92 Lift arm end, category I, right hand, 7/8" pin hole. Lift arm end, right hand, Spee-Ball for 7/8" & 1-1/8" pins. Can replace M92 & M92. Tractors: MF65, MF85, MF150, MF165, MF175, MF180, MF265 & MF275. Lift arm end, right hand, category II, 1-1/8" pin hole. Tractors: MF65, MF85, MF88, MF Super 90, MF175, MF180, MF255, MF265, MF270, MF275, MF283, MF290, MF383, MF390, MF393, MF670, MF E91 Lower lift arm with forged ball-joint ends, category I accomodates 7/8" drawbar or lower link pins. Universal arm for Massey Ferguson M91 right or left. 32" hole centers M92 Lift arm end, left hand, category II, 1-1/8" pin hole. Tractors: MF65, MF85, MF88, MF Super 90, MF175, MF180, MF255, MF265, MF270, MF275, MF283, MF290, MF383, MF390, MF393, MF670, MF690. Lower Link Shafts M M M1WC Lower lift arm, category I, universal right or left. Tractors: Late TO35, MF35, MF50, MF135, MF hole centers, 5/8 thick. Lower lift arm, category I, with replaceable ball end & 7/8" ball other end, universal right or left. Tractors: Early TO35, MF35, MF50, MH50, F40. Industrials: 202, 204. Standard 31-1/2" hole centers, 5/8" thick. Lower Lift Arm Balls Lift arm ball, category I, use in M91, M1 & M91 lift arms. Tractors: MF135, MF240, MF250, MF20D, MF M M3 Pivot shaft for lower link. Threaded ends 5/8" NF & 5/8" NF, 5-1/4" OAL. Tractors: TO20, TO30, TO35, MF35, MF135, MF150. Industrials: 2135, 3165, 202, 204. Pivot shaft, for lower link, except Orchard & Vine. Threaded ends 5/8" NF & 3/4" NF, 6" OAL. Tractors: MF230, MF231, MF235, MF240, MF245. Industrials: 20, 20C, 20D, 30 turf M1WC Lift arm ball, category II ball, use in M91, M92 & M92 lift arms. Tractors: MF135, MF M1 Clip, lower lift arm, use with M91, M1 & M1 lift arm balls. MF-6-144

166 6 HITCH AND HYDRAULICS Replacement parts to fit Lift Arm Repair End Lift Arm Lock Pin Kit Forged universal weld-on ends with ball joint. Repairs any lower arm. LLK65 Bushing kit, lift arm, contains M1 bushing, M1 spring & 2 each of M1 screw & M1 washer. Tractors: MF65, MF165, MF175, MF E E1 Lift arm repair end, bent, forged. Category I, 7/8" pin hole, 1-3/4" width at weld end. 5-1/4" overall length. Lift arm repair end, bent, forged. Category II, 1-1/8" pin hole, 1-3/4" width at weld end. 5-1/2" overall length. B2226 Lower Lift Arm Weld-On Ball Joints Weld-on ball joint, 5/8" bore. Category 0. Lower Link Reducing Sleeves 30544E1 Lift arm ball joint, 7/8" bore. Category E1 Lift arm ball joint, 1-1/8" bore. Category 2. Converts Category II to Category I 30291E1 P2004 Bushing, lower lift arm. Category II to category I, 1-1/8" to 7/8", 1-3/4" long. Lower lift arm reducer bushing. Category II to category I, 1-1/8" O.D. to 7/8" I.D., 1-3/8" long E1 Lift arm ball joint, 1-7/16" bore. Category 3. Lift Arm Cuff SBJ2 Lift arm combination ball joint. For 7/8" or 1-1/8" pins. Category I & II. 1/4" thick race for light arms. TLAC65L Lift arm cuff, one piece formed, no welded seams. For lower lift arm. Replaces TLAC65. SBJ3 Lift arm combination ball joint. For 7/8" or 1-1/8" pins. Category I or II. 7/16" thick race for heavy lift arms. MF-6-145

167 6 HITCH AND HYDRAULICS Quality Forged Top Links and Repair Parts Replacement top links with bright plated 1-1/8" threaded forged ends. Available in category I & category II. 16" & 20" body centers are one piece with swedged ends. Has easy to use locking device with its own handle. Adjustment handle is conveniently placed through body center E91 Top link, 20" body, 1" category II ball joints. Adjusts 25" to 37". Painted red E91 Replacement top link, 16" body, 3/4" category I ball joints. Adjusts 20-1/2" to 29" overall. Painted red. JSA2024R Top link, 24" body, 1" Category II ball joints. Adjusts 29" to 41". Painted red E91 Replacement top link, 20" body, 3/4" category I ball joints. Adjusts 25" to 35" overall. Pained red. JSA2221 Top link end, 1-1/8" right hand thread. Category II, 1" pin hole. JSA1024R Top link, 24" body, 3/4" category I ball joints. Adjusts 29" to 39" overall. Painted red. JSA2222 Top link end, 1-1/8" left hand thread. Category II, 1" pin hole. JSA1200R Top link, 16" body combination Category II tractor & Category I implement ends, Adjust 19-1/2" to 29-1/2" overall. Painted red. Economy Forged Top Link and Repair Parts JSA1111 Top link end, 1-1/8" right hand thread, Category I, 3/4" pin hole E91 Forged, plated ends with 1-1/8" threads. Category I only. 16" center body is one-piece with swedged ends. Easy to use lever type locking device. Convenient adjustment handle through body center. Top link, 16" body, 3/4" category I ball joints. Adjusts 20-1/2" to 29" overall. Dichromate plated center body. JSA1111 Top link end, 1-1/8" right hand thread, Category I, 3/4" pin hole. JSA1112 Top link end, 1-1/8" left hand thread, Category I, 3/4" pin hole. JSA1112 Top link end, 1-1/8" left hand thread, Category I, 3/4" pin hole E91 Category II top links. 16" body, 1" category II ball joints. Adjusts 21" to 33" overall. Painted red. MF-6-146

168 6 HITCH AND HYDRAULICS Replacement parts to fit Heavy Duty Category II Top Link and Repair Parts Original Type Top Link Assemblies and Repair Parts Original type top links with forged 1-1/8" threaded dichromate plated ends. Available in category I, category II or category I & II. One piece bodies are available in 18-3/4" or 21-1/2" sizes. Adjusting handle folds away flush with body. Forged repelacement ends will fit original center tubes E91 Heavy duty top link, 16" body, 1" category II ball joints. Forged ends with 1-1/4" NC threads. Swedged steel center section. Adjusts 23" to 32" overall. Dichromate plated Top link, category I, 1" threaded ends, 18-3/4" center tube, extends to 30-1/4". RE1717L Top link end, 1-1/4" left hand thread, category II, I" pin hole Top link, category I, 1" threaded ends, 21-1/2" center tube, extends to 32-1/2". RE1718R Top link end, 1-1/4" right hand thread, category II, I" pin hole A91 Top link, category I by category II, 1" threaded ends, 21-1/2" tube, extends 32-1/2" A91 Top link, category II, 1" threaded ends, 21-1/2" center tube, extends to 32-1/2" M93 Top link end, 1-1/16" left hand threaded implement end; category II, 1" pin hole. MF-6-147

169 6 HITCH AND HYDRAULICS Weld-On Ball Joints M93 Top link end, right hand threaded tractor end; category II, 1" pin hole E1 Ball joint, weld-on, 5/8" bore category 0. (A) 30538E1 Ball joint, weld-on, 3/4" bore, category I. (B) TL1218C Top link, category I & II ends. 18-3/4" center tube. Adjust from 23" to 30" E E1 Ball joint, weld-on, 1" bore, category II. (B) Ball joint, weld-on, 1-1/4" bore, category III. (A) Top Link Reducer Bushings TL2018C Top link, category II both ends. 18-3/4" center tube. Adjust from 23" to 30". B80209 Bushing, category I to category 0, 1-5/8" long, 3/4" O.D. x 5/8" I.D. P2007 Bushing, category II to category I, 1-15/16" long, 1" O.D., 3/4" I.D M92 Top link end, 1-1/16" left hand threaded implement end; category I, 3/4" pin hole. Replaces 30115E E1 Bushing, category III to category II, 2" long, 1-1/4" O.D., 1" I.D. Forged Weld-On Repair Ends 30541E1 Top link repair end. Category I 3/4" pin hole M91 Top link end, 1-1/16" right hand threaded, flat side, tractor end; category I, 3/4" pin hole E1 Top link repair end. Category II, 1" pin hole. MF-6-148

170 6 HITCH AND HYDRAULICS Replacement parts to fit Stabilizer Kits & Parts for TO Models, MF35, MF50 Stabilizer Kits & Parts for MF65, MF165, MF175, MF180 SK100 SK100HD Stabilizer kit for category I 3-point hitch, 31-1/2" hole spacing. Contains 2 arms, 2 brackets, 2 stabilizer pins with nut and lock washer, and 2 linch pins with chains. Tractors: TO20, TO30, TO35, F40, MH50, MF50. Stabilizer kit for category I, 3-point hitch, 31-1/2 hole spacing. Same as SK100 except contains 2-high alloy steel arms. SK65J SK65HCJ Stabilizer kit, low-clearance. Tractors: MF65, MF165, MF175, MF180. Contains 2 adjustable arms, right & left brackets, pins & hardware for mounting. Replaces & Stabilizer kit, high-clearance. Tractors: MF65, MF165, MF175, MF180. Contains 2 adjustable arms, right & left brackets, pins & hardware for mounting. Replaces & M M1-HD SK SK100-33HD M M1-HD /776M M1-WNL S36 DKPWCH Stabilizer arm for 3-point hitch, 31-1/2" hole spacing. Stabilizer arm for 3-point hitch, high alloy steel, 31-1/2" hole spacing. Stabilizer kit for category I 3-point hitch, 33" hole spacing. Contains 2 arms, 2 brackets, 2 stabilizer pins with nut & lock washer, & 2 linch pins with chains. Tractors: MF35, MF50, MF135, MF150, MF230, MF235, MF245. Stabilizer kit for category I 3-point hitch, 33" hole spacing. Same as SK except contains 2-high alloy steel arms. Stabilizer arm, 3-point hitch, 33" hole spacing. Stabilizer arm, 3-point hitch, high alloy steel 33" hole spacing. Stabilizer bracket. 3-point hitch, universal, left or right hand. Stabilizer pin with nut & lock washer. Nut, 5/8"-18 x 1-1/16" for M1-WNL pin. Lock washer, 5/8" for M1-WNL pin. Linch pin with ring & chain, 7/16" pin dia. x 1-5/8" long, 1-11/16" ring dia., DKP pin with safety chain. SK6756 SK150FA JSA M M1 SKB62 SKB63 SKB67 SKB68 Stabilizer kit, standard-clearance. Tractors: MF65, MF165, MF175, MF180. Contains 2 adjustable arms, right & left brackets, pins & hardware for mounting. Replaces & Stabilizer kit, flat axle models. Tractors: MF150, MF165, MF175, MF180. Contains 2 adjustable arms, right & left brackets, pins & hardware for mounting. Stabilizer arm, complete with both ends. Adjustable from 27-1/2" to 37"; body length 23"; thread size 7/8"; pin holes 7/8". End only for JSA1003 stabilizer arm. 7/8" national fine left hand thread, 7/8" pin hole, 9-1/8" length, center of hole to end. End only for JSA1003 stabilizer arm. 7/8" national fine right hand thread, 7/8" pin hole, 8-7/8" length, center of hole to end. Stabilizer bracket, left hand for high-clearance tractors (SK65-HCJ). 6-1/2" drop-under axle. Stabilizer bracket, right hand for high-clearance tractors (SK65-HCJ). 6-1/2" drop-under axle. Stabilizer bracket, left hand for low-clearance tractors (SK65J). 3-1/2" drop-under axle. Stabilizer bracket, right hand for low-clearance tractors (SK65J). 3-1/2" drop-under axle. SKB69 Stabilizer bracket, right hand for standard clearance tractors (SK-6756 & SBK-3250). 3" drop-under axle. MF-6-149

171 6 HITCH AND HYDRAULICS SKB70 SKB150 Stabilizer bracket, left hand for standard clearance tractors (SK-6756 & SBK-3240). 3" drop-under axle. Stabilizer bracket, right hand or left hand for flat axle tractors. 5-1/2" drop-under axle. Linkage Pins Massey Ferguson replacement pins Stabilizer Kits for Industrial Tractors 30127E91 Top link pin. Category I, 3/4" pin dia., 2-7/8" useable length, 4-5/8" overall length E91 Top link pin. Category I, 3/4" pin dia., 3-7/8" useable length, 5-5/8" overall legnth. Replaces M1. P2325 Top Link pin. Category II, 1" pin dia., 3-1/4" useable length 4-3/4" overall length E91 Top link pin Category II, 1" pin dia., 4-1/2" useable length, 6" overall length. Replaces P2450. SK-IND M2TSK M M1WN P7065 Stabilizer kit. Contains 4 mounting brackets with pins & 2-JSA5050 top links. Fits most 3-point hitches on light industrial models. Telescoping Stabilizer Stabilizer, telescoping arm, for 3-point hitch. Adjustable from 26" to 35". Tractors: MF250, MF251, MF253, MF255, MF261, MF265, MF270, MF275, MF283, MF285, MF290, MF298, MF360, MF375, MF383, MF390, MF390T, MF393, MF396, MF396T, MF398, MF399, MF670, MF690, MF698, MF1085. Bracket, used with telescoping stabilizer M2TSK. Pin with nut, use with bracket M2 & M2TSK telescoping stabilizer. Stabilizer Pins Stabilizer pin. 5/8" fine threaded end, 7/8" pin end with 1/2" working area. Use nut & 34811S36 lock washer M M M E E E91 P E91 P2005 P7212 Top link pin Category I, 3/4" dia., 3" useable length, 4-5/8" overall length. Top link pin. Category I, 3/4" dia., 4" useable length, 5-5/8" overall length. Top link pin Category I, Hinged upper hitch pin assy. 3/4" dia., 9-5/8" useable length. Tractors: TO35, MF35, F40, MF50, MF65. Lower link pin. Category I, 7/8" pin dia. 1-3/4" useable length, 5-1/2" overall length, 7/8" thread dia. adj. jam nut. Replaces P2009. Lower link pin. Category I, 7/8" pin dia., 2" useable length, 6-3/16" overall length. 7/8" thread dia. adj. jam nut. Replaces P2009-L. Lower link pin. Category I, 7/8" pin dia., 1-3/4" useable length, 5-1/2" overall length, 7/8" thread dia. fixed shoulder. Replaces P2000. Lower link pin. Category II to I, 1-1/8" pin dia., 1-3/4" useable length, 5-1/8" overall length, 7/8" thread dia., adj. jam nut. Replaces 30135E91. Lower link pin. Category II to I, 1-1/8" pin dia., 2-1/4" useable length, 6-1/2" overall length, 7/8" thread dia. fixed shoulder. Replaces P6502. Lower link pin. Category II, 1-1/8" pin dia., 1-3/4" useable length, 6-1/4" overall length, 1-1/8" thread dia., adj. jam nut. Lower link pin. Category II, 1-1/8" pin dia., 2" useable length, 6-5/16" overall length, 1-1/8" thread dia., fixed shoulder. Replaces 30138E M1-WNL Anchor pin with nut & lock washer. 7/8" dia., 3" overall length, 1" useable length, 5/8"-18 thread 1-3/16" thread length. MF-6-150

172 6 HITCH AND HYDRAULICS Replacement parts to fit Lower Stay Anchor Pin Kit For MF65 Drawbars M1 Drawbar, category I, 7/8" pins. 11 holes, 26" bar length. PLSK M1 Stabilizer pin kit. Contains pin, bushing & special nut. Tractor: MF65. Stabilizer pin. Tractor: MF M1HT DB212 Drawbar, heat treated, category I, 7/8" pins. 11 holes, 26" bar length. Drawbar, category II, 1-1/8" pins, 3" wide, 1-1/4" thick, 32" useable length, thirteen 3/4" dia. holes. Painted red M M1 Stabilizer bushing. Tractors: MF 65, MF180. Special hex nut, stabilizer pin. Tractors: MF65. Stay Chain & Clevis Kit DB214 Drawbar, category II, 1-1/8" pin, one piece, high carbon steel, 3" wide, 1-1/4" thick, 32" useable length, seven holes, 1-1/8" dia. Painted red. Drawbar Stay Arms WP Stay chain & clevis kit, with pins. Tractors: TO20, TO30, TO35, MF35, MF /2" long. Clevis & Pin Kit DBSU DBSL Stay arm upper, 1/4" thick steel. Tractors: TE20, TO20, TO30. Stay arm lower, 1/4" thick steel. Tractors: TW20, TO20, TO30. Swinging Drawbar Assembly Kit includes drawbar, hanger & clevis assembly M1 Clevis, pin & cotter key, 2 of each. Tractors: TO20, TO30, TO35, F40, MF50. Clevis Eyebolt Assembly SDA6 SDA1 Swinging drawbar kit. Contains drawbar, hanger & clevis assembly. Tractors: TO20, TO30, TO35, MF50. Drawbar. 2" wide, 7/8" thick, 30-3/8" long. SDA2 Clevis assembly with pins, for SDA6. SDA3 Drawbar hanger. PT3 Pin for clevis assembly, 7/8" dia. CEK M91 Lift arm eyebolt kit. Contains eyebolt assembly with bushing & nut. Tractors: TO20, TO30, TO35, MF50. Eyebolt assembly, lift arm sway chain. Tractors: TO20, TO30, TO35, MF35, MF50. SDA75 SDA2-75 Swinging drawbar kit. Contains drawbar, hanger & clevis assembly. Tractors: MF35, MF50, MF65, MF135, MF150, MF165 (requiring 3/4" clevis studs). Clevis assembly with pin, for SDA M1 Bushing, for lift arm eyebolt assembly M1. MF-6-151

173 6 HITCH AND HYDRAULICS Pivot Pin For Swinging Drawbar Linch Pin Merchandiser M Pivot Pin, for swinging drawbar. 1" O.D. by 1-7/8" working length. Fits original swinging drawbar M1. Tractors: TO35, MF35, MH50, MF50, MF65, MF135, MF150, MF165, MF230, MF235, MF245, MF255. Industrials: MF20C, MF30B, MF40B, MF3165. Drawbar Bolt Bolt for swinging drawbar support, 3/4" 1-3/4" national coarse thread with special cone neck & grip lock adhesive. Tractors: MF135, MF150, MF165, MF175, MF180, MF230, MF235, MF245, MF255, MF265, MF275, MF285, MF298, MF698, MF699, MF1080. Industrials: 20, 20C, 30, 30B, 31, 40B, 50C. Replaces Hitch Pins With Hair Pin Lock DKLP200 Linch pin merchandising display. Box of 200, DKLP-91, 7/16" dia. x 1-3/4" long, 1-5/8" dia. ring. Agricultural Implement Linch Pins DKLP91 Linch pin, 7/16" dia. pin x 1-3/4" useable length, 1-5/8" dia. ring. DKPWCH DKP1/4 DKP3/16 DKP-SD-1 Linch pin with ring & chain, 7/16" pin dia. x 1-5/8" long, 1-11/16" ring dia., DKP pin with safety chain. Linch pin, 1/4" O.D. pin x 1-1/4" long. Linch pin, 3/16" O.D. pin x 1-1/4" long. Linch pin, heavy-duty, 7/16" dia. pin, 1-7/8" useable length, 1-5/8" dia., extra heavy ring. P6254 P6256 Hitch pin, 5/8" x 4-1/2" useable length. Hitch pin, 5/8" x 6-1/4" useable length. Hydraulic Reservoir Dip Stick 30285E1 Hitch pin, 3/4" x 4-1/4" useable length E1 Hitch pin, 3/4" x 6-1/4" useable length. P8754 7/8" x 4-1/4" hitch pin E1 P1004 P1006 Hitch pin, 7/8" x 6-1/4" useable length. 1" x 4-1/4" hitch pin. Hitch pin, 1" x 6-1/4" useable length M1 Hydraulic oil level indicator. Tractors: TO20, TO30, TO35. Hydraulic Pump O-Ring Kit M91 Hydraulic Pump O-Ring Kit, 26 pieces to repair or service hydraulic lift pump. Tractors: TO35, MF35. MF-6-152

174 6 HITCH AND HYDRAULICS Replacement parts to fit M M92 Gasket For Pump Base Drain Plug Gasket, pump base drain plug, also transmission filler plug. Tractors: TO20, TO30. Hydraulic Lift Pumps Hydraulic lift pump " O.D. 21-spline shaft, for models with pressure control valve. Tractors: MF230, MF240, MF245, MF250, MF255, MF265, MF270, MF275, MF282, MF283, MF290, MF298, MF670, MF690, MF698, MF699. Industrials: 20C, 20D, 30, 30B, 30D, 30E, 31, 40, 40B, 50C, 50D, 50E. Replaces M94, M92, M92, M92, M M92 HPOK1 9N621KIT M1 Hydraulic lift pump. Tractors: MH50, MF133, MF135, MF140, MF148, MF152, MF165, MF168, MF175, MF178, MF185, MF188, MF1200. Industrials: 20C, 50. Hydraulic Lift Pump Repair Parts Hydraulic pump overall kit. Contains cam blocks, pistons, chamber kits, PTO shaft bushing, relief valve, & gaskets. Tractors: TE20, TO20, TO30. Repair kit, hydraulic pump chamber. Tractors: TE20, TO20, TO30. Cam block, hydraulic pump. Tractors: TE20, TO20, TO M93 Hydraulic lift pump assembly. 1-3/8" O.D. 10-spline shaft. Tractors: TO35 (s/n & up), MF35, MF50, MF65. Industrials: 203, 205, 202 & 204 work bull models M1 Piston, hydraulic pump. Tractors: TE20, TO20, TO M1 Hydraulic pump, Tandem main pump, single stage. Tractors: MF2640, MF2675, MF2705, MF2745, MF2775, MF2805, MF3505, MF3525, MF3545, MF3630, MF3645, MF3650, MF3655, MF3660, MF3670, MF3680, MF3690, MF8120, MF8140, MF8150, MF8160. Replaces M1, M M1 Bushing, hydraulic pump base, for PTO shaft. Tractors: TE20, TO20, TO M91 Hydraulic auxilary tandem pump. Tractors: MF174F, MF184F, MF194F, MF362, MF374S, MF374F, MF375, MF382, MF383, MF384S, MF390, MF390T, MF394S. Replaces M91, M91, M91, M91, M M91 Hydraulic auxilary pump. Tractors: MF396, MF399 (ENGINE ). Replaces M91, M91. MF-6-153

175 6 HITCH AND HYDRAULICS Hydraulic Lift Pump Repair Kits Valve Chamber Repair Kit HPOK3WCB HPOK2WCB Hydraulic pump overhaul kit. Contains valve chamber assemblies, pistons, piston rings & cam blocks. Tractors: TO35 (s/n & up), MF35, MF50 (s/n & up), MF65, MF135, MF165 using M1.91 diameter piston. Hole sizes: (B) 3/8" 9.5mm; (C) 7/16" 11.1mm; (D) 15/32" 11.9mm. Hydraulic pump overhaul kit. Contains valve chamber assemblies, pistons, piston rings & cam blocks. Tractors: MF135, MF150, MF165 (using.98 diameter piston), MF175, MF180. Hole sizes: (B) no hole; (C) 33/64" 13.1mm; (D) 3/8" 9.5mm M91 Chamber repair kit, hydraulic pump valve. Contains valves, springs, snap rings & o-rings to repair all 4 chamber ports in one tractor. Services M1 & M1 body on early TO35. Tractors: TO35, MF35, MF50, MF65, MF135, MF150, MF165, MF175, MF180. Hydraulic Pump Valve Chamber Assemblies HPOK3LCB HPOK2LCB M2 Hydraulic pump overhaul kit. Contains valve chamber assemblies, pistons, & piston rings. Tractors: TO35 (s/n & up), MF35, MF50 (s/n & up), MF65, MF135, MF165 (using M1.91 diameter piston). Hole sizes: (B) 3/8" 9.5mm; (C) 7/16" 11.1mm; (D) 15/32" 11.9mm. Hydraulic pump overhaul kit. Contains, valve chamber assemblies, pistons, & piston rings. Tractors: MF135, MF150, MF165 (using.98 diameter piston), MF175, MF180. Hole sizes: (B) no hole; (C) 33/64" 13.1mm; (D) 3/8" 9.5mm. Cam Blocks, Hydraulic Pump Cam block, front, hydraulic lift pump, with lip. Tractors: TO35, MF35, MF50, MF65, MF135, MF165, MF175, MF180. Supersedes & replaces M M1VA M M3VA Hydraulic pump valve chamber assembly. Contains valves, springs, plugs, o-rings, & snap rings installed. Tractors: TO35 (s/n & up), MF35, MF50 (s/n & up), MF65, MF135, MF165 using M1.91" diameter piston. Hole sizes: (B) 3/8", 9.5mm. (C) 7/16", 11.1mm. (D) 15/32", 11.9mm. O-ring, hydraulic pump valve chamber to pump body, 1/6" x 7/16" I.D. (9 required). Hydraulic pump valve chamber assembly. Contains valves, springs, plugs, o-rings, & snap rings installed. Tractors: MF135, MF150, MF165 using.98" diameter piston; MF175, MF180. Hole sizes: (B) no hole. (C) 33/64", 13.1mm. (D) 3/8", 9.5mm M2 Cam block, rear, hydraulic lift pump, without lip. Tractors: TO35, MF35, MF50, MF65, MF135, MF165, MF175, MF180. Supersedes & replaces M1. MF-6-154

176 6 HITCH AND HYDRAULICS Replacement parts to fit Hydraulic Pump Pistons, Rings Lift Pump Control Valves M92 Valve assembly, hydraulic pump control. Tractors: MF35, MF50, MF M92 Valve assembly, hydraulic pump control. Tractors: MF135, MF150, MF165, MF175, MF M M M1 Piston, hydraulic lift pump. Tractors: TO35 (prior to s/n ), MF50 (prior to s/n , using.80" diameter piston). No rings required. Piston, hydraulic lift pump. Tractors: TO35 (s/n & up), MF35, MF50 (s/n & up), MF65, MF135 & MF165 (using.91" diameter piston). Supersedes & replaces M1. Piston ring,.91" dia. hydraulic lift pump, 2 required on piston M1. Supersedes M M Valve assembly, conversion service kit, hydraulic pump control. Contains valve M93, plus components to convert & replace M92 in early production. Tractors: MF135, MF150, MF165, MF175, MF180. O-ring, for lift pump control valves, 3/32" x 3/4" I.D. For use with M92 & M M M M1 Piston, hydraulic lift pump. Tractors: MF135, MF150, MF165 (using.98" diameter piston), MF175, MF180. Piston ring,.98" dia. hydraulic lift pump, 2 required on piston M1. Needle Bearing For Hydraulic Lift Pump Needle bearing, for recess in rear of camshaft for hydraulic lift pump. B108 bearing,.625" I.D.,.812" O.D.,.500" wide. Tractors: TO35, MF35, MH50, MF50, MF65, MF135, MF150, MF165, MF175, MF180, MF230, MF231, MF235, MF240, MF245, MF250, MF253, MF255, MF265, MF270, MF275, MF282, MF283, MF285, MF290, MF298, MF360, MF375, MF383, MF390, MF390T, MF398, MF399, MF670, MF690, MF698, MF699, MF1080, MF1085. Industrials: 20, 20C, 20D, 30, 30B, 30D, 30E, 31, 35, 40, 40B, 40E, 50C, 50D, 50E, 202, 203, 204, 205, 302, 304, 2135, M91 Control valve, hydraulic lift pump, with collar & retainer. Tractors: MF231, MF240, MF250, MF255, MF265, MF270, MF275, MF290, MF298, MF360, MF365, MF383, MF390, MF393, MF399, MF670, MF690, MF698, MF699. Industrials: 20D, 30, 30B, 30D, 30E, 40B, 40E, 50C, 50D, 50E. Also for lift pumps on the following models except MKII pumps/pumps with rear mounted safety valve. Tractors: MF230, MF235, MF245. Industrials: 20C, 31, 40. Replaces M91. MF-6-155

177 6 HITCH AND HYDRAULICS Safety Relief Valves Hydraulic Front Pump M M M M M M94 Relief valve, hydraulic pump. Tractors: TO20, TO30. Relief valve, hydraulic pump, 2550 psi. Tractors: TO35, MF50, MF65, MF135, MF150, MF165, MF175, MF180. Relief valve, hydraulic pump, 2750 psi. Tractors: MF30, MF135, MF150, MF165, MF175, MF180, MF235, MF255. O-ring for relief valves. Auxiliary Hydraulic Pump Auxiliary hydraulic pump assembly. Tractors: MF165, MF175, MF180, MF235, MF240, MF245, MF250, MF253, MF255, MF265, MF270, MF275, MF283, MF285, MF290, MF298, MF670, MF690, MF698, MF699, MF1085. Industrial: 30. Replaces M93, M93, M92, M91, M91, M91. Hydraulic pump assembly, less auxiliary hydraulic system. Tractors: MF135, MF150, & MF165 with rear axle s/n C5051 & up. MF175, MF235, MF240 (s/n 2773 NO1001 & up), MF245, MF255, MF265. Industrials 20C, 30, 30E, 31, 40B, 50C, 50D, 50E (with independent PTO). L LB Hydraulic pump, less bracket RPM. Can replace M91 by changing the in & out plumbing. SAEA mounting. 3-1/4" pilot, 4-3/8" bolt spacing on 2 bolt flange M M1 Pump, hydraulic front mount for backhoes, crawlers, forklifts, & loaders, 7/8" 13-spline shaft GPM at 2000 rpm. Tractors: MF30, MF32, MF32A, MF34A, MF34B, MF40, MF52, MF54, MF100, MF200, MF212, MF225, MF235, MF400C, MF2200, MF2244, MF2500, MF4500, MF6500. H10190RF210RM adapter included. Hydraulic pump, Tandem main pump, single stage. Tractors: MF2640, MF2675, MF2705, MF2745, MF2775, MF2805, MF3505, MF3525, MF3545, MF3630, MF3645, MF3650, MF3655, MF3660, MF3670, MF3680, MF3690, MF8120, MF8140, MF8150, MF8160. Replaces M1, M2. MF-6-156

178 6 HITCH AND HYDRAULICS Replacement parts to fit L Pump Drive Couplers for Loader Backhoes L601-9 Pump Drive Couplers for Loader Backhoes L Coupler complete, Morflex series 302. Contains center member, 2 drive flanges with set screws, & 4 bolts with lock nuts M91 Center member for L601-14, 3-1/8" dia., four 1/4" holes, 1-15/16" spacing. Same as L L601-9 Coupler complete, Morflex series 352. Contains center member, 2 drive flanges with set screws, & 4 bolts with lock nuts M91 Center member for L601-9, 3-5/8" dia., four 5/16" holes, 2-1/4" spacing. Same as L M91 Z80507 Drive flange for L601-14, 3/4" round bore with set screw 1/4" x 3/8". 1-15/16" spacing. Same as L36-3. Capscrews for L601-14, 1/4"-28 x 1-1/2", Gr 5, hex head M1 Drive flange for L601-9, 3/4" round bore with set screw 1/4" x 3/8". 2-1/4" spacing. Same as L36-7. L80-7 Capscrews for L601-9, 5/16"- 24 x 1-5/8", gr 5 hex head. H61-16 Self locking hex nuts for L601-14, 1/4"-28. L61-2 Self locking hex nuts for L601-9, 5/16"-24. L36-4 L36-5 Optional drive flange for L601-14, 5/8" round bore with set screw 1/4" x 3/8" #SSH /16" spacing. Optional drive flange for L601-14, 7/8" round bore with set screw 1/4" x 3/8" #SSH /16" spacing. L36-6 L36-8 Optional drive flange for L601-9; 5/8" round bore with set screw 1/4" x 3/8" #SSH /4" spacing. Optional drive flange for L601-9; 7/8" round bore with set screw 1/4" x 3/8" #SS /4" spacing. L36-19 Optional drive flange for L601-9; 1" round bore with set screw 1/4" x 3/8" #SS /4" spacing. L78-13 Optional drive flange for L601-9, 13-spline for 7/8" dia. shaft 5/16" dia. bolt holes 2-1/4" on center. MF-6-157

179 6 HITCH AND HYDRAULICS M M M M M92 Adapter Plates & Drive Shafts For front mounted hydraulic pumps. Adapter plate, for front mounted hydraulic pump drive. 5-1/4" dia. with 3 bushings, mounting holes 3.465" on center, 4" bolt circle, 3/4" left hand threaded center hole. Tractors: MF35, MF150, MF65, MF135, MF150, MF235 orchard, MF245 orchard. Industrials: 20, 20C, 30, 30B, 30D, 35, 40, 50, 202, 203, 204, 205, 2135, Adapter plate, for front mounted hydraulic pump drive. 5-1/4" dia. with 4 bushings, mounting holes 2.835" on center, 4" bolt circle, 7/8" left hand threaded center hole. Tractors: MF135 orchard, MF165, MF175. Industrials: 30, 40B, 50A, 50C, 50D, 2200, Bushing for front mount hydraulic adapter plates. Tractors: MF35, MF50, MF65, MF135, MF150, MF165, MF175, MF235 orchard, MF245 orchard. Industrials: 20, 20C, 30, 30B, 30D, 35, 40, 40B, 40E, 50, 50A, 50C, 50D, 202, 203, 204, 205, 2135, 2200, Used in adapter plates M93 & M91. Drive shaft with coupler attached. For front mounted hydraulic pump drive, 11-3/8" overall length, adapter end 3/4" left hand threads, coupler end 3/4" round bore with 3/16" keyway. Tractors: MF135 orchard. Industrials: 20, 35 utility, 202 (s/n & up), 203, 204 (s/n & up), 205, Drive shaft with coupler attached. For front mounted hydraulic pump drive, 11-5/8" overall length, adapter end 3/4" left hand threads, coupler end 7/8" 13-splines. Industrials: M M M M M4 Drive shaft with coupler attached, for front mounted hydraulic pump, 14-1/8" overall length, adapter end 7/8" left hand threads, coupler end 7/8" 13-splines. Tractors: MF165, MF175. Industrials: 30, Drive shaft with coupler attached, for front mounted hydraulic pump. 15-1/2" overall length, adapter end 7/8" left hand thread, coupler end 7/8" 13-splines. Industrials: 40B, 50A. Drive shaft with coupler attached, for front mounted hydraulic pump, 15-7/8" overall length, adapter end 7/8" left hand threads, coupler end 7/8" 13-splines. Industrials: 50C, 50D. Hydraulic Lift Pump Filter Element Filter element for hydraulic lift pump, top mount. 2-7/16" O.D. 1-29/32" I.D. & 4" long. Tractors: MF35, MF50, MF65, MF85, MF88, MF90, MF1080. Industrials: 202, 203, 204, 205, 302, 304, 2135, 2200, Also for models with pumps having 10-spline camshaft. Tractors: MF135, MF150, MF165, MF175, MF180. Industrials: 20, 30, 31, 40, 302, 304. Filter, hydraulic oil cooler, multi-power transmission. Tractors: Super 90, MF135, MF165, MF175, MF180, MF1080, MF1100, MF1130. Industrials: 30, 30B, 30E, 40, 50A, 50E, 50F, 204, 205, 302, M91 Drive shaft with coupler attached, for front mounted hydraulic pump drive, 12-3/8" overall length, adapter end 3/4" left hand threads, coupler end 7/8" 13-splines. Industrials: 20C, 30B, 30D. MF-6-158

180 6 HITCH AND HYDRAULICS Replacement parts to fit Hydraulic Oil Filter Assembly Break-Away Clamps M M1 Oil filter assembly, hydraulic, with 25 micron element, 20 gallon per minute spin-on filter with in-line mounting head having 3/4" ports. Head has by-pass feature set at 15 psi. Rated at 200 psi. Same as SF1-25. Oil filter element, hydraulic, 25 micron. Used on M91. Same as 1A9023. Loader/Backhoe Cylinder Packing Kits Break-away clamp, single, hydraulic M91 S M1 Break-away clamp, double, hydraulic (5006-4). Break-away clamp, double, hydraulic. For use with S20-4 & S40-4 couplers. Quik-cover assembly HV4957 fits this clamp. Dust Covers Rubber plug with chain & ring. For Pioneer hydraulic couplers (5205-4) M92 Loaders: 200 (lift cylinder and self leveling). Pioneer Hydraulic Couplers External Hydraulic Valve - Single Spool M91 Quick coupler, hydraulic, female body half, 1/2" NPT. Same as M1 Quick coupler, hydraulic, male tip half, 1/2" NPT. Same as M Quick coupler, hydraulic, female body half, 3/4"-16 SAE. Same as Quick coupler, hydraulic, male tip half, 3/4"-16 ORB thread, 2500 PSI. 1-1/16" hex size. Converts tractor for operation of cylinders on pull type implements, front loaders, hydraulic motors, or other optional external hydraulics. Single spool, double acting control valve mounts conveniently on flat or shell fenders. Selector/isolator allows operation of single or double acting cylinders. Mounting hardware & instructions included. For all TO35 & later Massey Ferguson models where M1 lift cover plate is accessible Quick coupler, hydraulic, female body half, 1/2" NPT. Couples under pressure from both sides. TS3200M External hydraulic valve kit, single spool, double acting control valve. Contains isolator valve, valve, couplers, clamp, hoses, adapters, hardware, & instructions. MF-6-159

181 6 HITCH AND HYDRAULICS Selector/Isolator Assembly Combination one-way or two-way isolator-selector allows single acting or double acting external hydraulic service. TS300 Selector/isolator assembly. For TO35 & later tractors thru MF1080, without individual external hydraulic systems. Three-position spool, forward position allows one-way (push) for single acting cylinder. Center position allows operation of the 3-point arms, & the rear position will feed power to a 4-way control valve for two-way (push-pull) operation of double acting cylinder. Fits all MF tractors where M1 lift cover is used. Remote Hydraulic Valve Kit Application: Massey Ferguson Tractors TO35 thru MF1080. Note: Coupler kits must be ordered separately, to provide quick-couplers and hoses for the third spool of this valve. HV4298 Replaces S42-4 S H31-SPL-44 Coupler kit for TISCO 4000 series valves. Description Qty in HV4298 CLAMP 1 COMPLETE COUPLER 2 DUST PLUG 2 HYD HOSE ASSY 2 MF-6-160

182 6 HITCH AND HYDRAULICS Replacement parts to fit HV4000 Series Remote Hydraulic Valve Kits Application: For TO35 to MF1080 models originally equipped with a M1 two-bolt manifold plate (transfer cap) at top of hydraulic system. This plate is located just forward of the operator s seat on top of the hydraulic top cover. Major Sales Features: Isolator selector is installed in place of the manifold plate. Select either internal or external system operation-not simultaneous operation. Installation is quick, clean & simple. Valve can be installed in any convenient location on tractor fender or inside wall of cab. Kit contains all hoses & couplers for all spools. Improved quick couplers allow one hand hook up of hydraulic cylinder hoses (Safeway S40-4 coupler). Hydraulic coupling plugs. HV4211 HV4220 HV4221 Replaces S42-4 S HV4970 HV4971 HV4972 HV4973 HV4012 HV4020 HV4021 TS300 Single spool hydraulic valve kit. Contains a 1 spool valve with handle, selector valve, quick-coupler (female half), break-way clamp, dust plugs, and hoses. Double spool hydraulic valve kit. Contains a 2 spool valve with handles, selector valve, quick-coupler (female half), break-way clamp, dust plugs, & hoses. Double spool hydraulic valve kit with one float spool. Contains a 2 spool valve with handles, selector valve, quick-coupler (female half), break-way clamp, dust plugs, & hoses. Description CLAMP COMPLETE COUPLER DUST PLUG HYD HOSE ASSY HYD HOSE ASSY HYD HOSE ASSY HYD HOSE ASSY HYDRAULIC VALVE KIT HYDRAULIC VALVE KIT HYDRAULIC VALVE KIT ISOLATOR VALVE Qty in HV Qty in HV Special Hose Assemblies Qty in HV Replaces HV4970 HV4971 HV4972 HV4973 H31-SPL-32 H31-SPL-36 H31-SPL HOSE TYPE 3/8" - 1 wire 3/8" - 1wire 3/8" - 1 wire 3/8" - 1 wire 3/8" - 1 wire 3/8" - 1 wire 3/8" - 1 wire 3/8"-1 wire HOSE END LEFT 9/16" - 18 ORB 90 Male Swivel 9/16" ORB Male Swivel 9/16" - 18 ORB 90 Male Swivel 9/16" - 18 ORB 90 Male Swivel 9/16" - 18 ORB 90 Male Swivel 9/16" - 18 ORB 90 Male Swivel 9/16" - 18 ORB 90 Male Swivel 3/8" NPT 90 Male Swivel OVERALL LENGTH (IN) 18" 21" 30-1/2" 32-1/2" 32" 36" 44" 24" HOSE END RIGHT 1/2" NPT Male Solid 1/2" NPT Male Solid 3/8" NPT Male Solid 3/8" NPT Male Solid 3/8" NPT Male Solid 1/2" NPT Male Solid 1/2" NPT Male Solid 1/2" NPT Female Solid MF-6-161

183 6 HITCH AND HYDRAULICS Hydraulic Valve Replacement Handles and Parts HV4988 Handle, offset, used in HV4984 & HV4985 valve assemblies. HV4989 Handle, straight. Used in HV4984 and HV A92 Hydraulic valve, 3-spool, 3/4" ORB work points, with manifold & two elbows. For tractors: MF35 & later models thru MF1080. This valve allows operator to use auxiliary hydraulics & 3-point lift at the same time without switching valves. Valve mounts underneath the seat, some tractors may require slight seat modification. Control Valves For External Hydraulic Kits HV4990 HV4998 HV4999 HV4987 Handle, hydraulic valve, for 4000 series valve. 90 degree short angle. Handle, hydraulic valve, for 4000 series valve. 70 medium angle. Handle, hydraulic valve, for 4000 series valve. 45 long angle. Knob, hydraulic valve handle, for 4000 series valve. HV4975 Link kit, hydraulic valve handle, for 4000 series valve. TS200BA Valve for TS3200M. Single spool, 4-way, 3-position, spring loaded to neutral. No relief valve, no power beyond option. In & out ports 3/4", work ports 1/2" NPT. MF-6-162

184 6 HITCH AND HYDRAULICS Replacement parts to fit HV4000 Series Hydraulic Valves One Spool Valves HV4000 Valve Components HV4910 Handle kit for 4000 series hydraulic valve. Includes handle & mounting hardware. HV4911 Handle mounting kit for 4000 series hydraulic valve, includes bail & hardware for mounting the HV4910 standard handle. HV4010 HV4012 Valve, hydraulic, with handle, single spool, 2000 psi. relief, tandem (4-way) spool, spring center to neutral. Valve, hydraulic, with handle, single spool multi-valve. NO RELIEF, tandem (4-way) spool, convertible to 3-way, spring center to neutral, with 90 rotated handle. Two Spool Valves HV4917 HV Handle kit for 4000 series hydraulic valve, includes handle & mounting kit with hardware. Has special bracket used for 90 rotated handle. 90 Handle mounting kit for 4000 series hydraulic valve, includes hardware for mounting the HV handle kit. Replaces HV4913. HV4923 Spool seal kit for 4000 series hydraulic valve, front & rear spool sealing o-rings. HV4020 HV4021 Valve, hydraulic, with handles, two spool, 2000 psi. relief, tandem (4-way) spools, spring center to neutral. Valve, hydraulic with handles, two spool, 2000 psi. relief, one spool tandem (4-way) float position with spring center to nuetral & one spool tandem (4-way) spring center to neutral. Three Spool Valves HV4930 HV4931 Float spool detent kit for 4000 series hydraulic valve. Contains all parts needed to convert standard spool to a float spool. Standard spring center kit for 4000 series hydraulic valve. Kit contains all parts needed to repair or convert existing spool. *Note: On any two spool valve, only one spool can be equipped with a float detent. HV4030 HV4034 Valve, hydraulic, with handles, three spool, 2000 psi. relief, all spools tandem (4-way) spring center to neutral. Hydraulic valve, three spool, less handles psi relief valve, one spool 3-way spring centered with one position detent. Two spools 4-way spring center to neutral. HV4932 Three position detent kit (no spring) for 4000 series hydraulic valve. Any tandem action spool can be converted to detent using this kit. Spool will remain in detent position until physically moved to neutral. NOT A PRESSURE RELEASE DETENT KIT. MF-6-163

185 6 HITCH AND HYDRAULICS HV4000 Series Hydraulic Valves HV4940 HV4941 Power beyond plug kit for 4000 series hydraulic valve. Can be installed in place of allen head plug in side of valve casting. Allows plumbing additional hydraulic control valve into system. Closed center plug kit for 4000 series hydraulic valve. Can be installed in place of allen head plug in side of valve casting. Allows use of valve with closed center hydraulic system (such as MF1100 series with variable displacement hydraulic pump). MF-6-164

186 6 HITCH AND HYDRAULICS Replacement parts to fit Hydraulic Top Link Cylinders Standard Tisco cylinders, all ports 9/16"-18 ORB with two adapters 9/16"-18 ORBM x 1/4" NPTM 90 degree swivel. HTL2101-2" bore for MF40 HTL3102-3" bore for standard category II replacement on most US tractors to 80 hp HTL3103-3" bore for MF50E HTL3106-3" bore for industirals 20C and 206. Replaces HTL2101 HTL3102 HTL3103 HTL3106 Equiv. Gannon ** * STROKE LENGTH 8" 8" 8" 8" CLOSED LENGTH A 24-1/16" 21" 26" 20" BARREL LENGTH B 12-7/16" 12-7/16" 12-7/16" 12-7/16" ROD HOLE DIA. C 3/4" 1" 1" 3/4" ROD END WIDTH D 1-3/4" 1-3/4" 1-3/4" 1-3/4" BASE END DIA. E 3/4" 1" 1" Hydraulic Side Link Cylinders Standard Tisco cylinders. All ports 9/16" 18 ORB with two adapters 9/16" - 18 ORBM x 1/4" NPTM swivel. 3/4" BASE END WIDTH F 1-3/8" 1-3/4" 1-3/4" 1-3/8" BASE TO BALL C/L 7-9/16" 2-1/2" 5-1/2" 3-1/2" HSL3203-3" bore for MF50C. Replaces HSL3202 EQUIV. GANNON STROKE LENGTH 4" A1 A2 A3 23" BARREL LENGTH B 8-7/16" Hydraulic Cylinder Seal Kits CLEVIS DEPTH C 3/4" CLEVIS WIDTH D 3/4" BASE END DIA. 3/4" BASE END WIDTH 2" BASE TO BALL C/L 3" HSK2002 Seal kit, for 2" bore HTL & HSL series top & side link cylinders. Contains seals & o-rings for 2" cylinder repair. For cylinders HTL2101, HTL2102, HTL2103, HSL2201, HSL2202, HSL2203. Replaces HSK2001. HSK3002 Seal kit, for 3" bore HTL & HSL series top & side link cylinders. Contains seals & o-rings for 3" cylinder repair. For cylinders HTL3101, HTL3102, HTL3103, HSL3201, HSL3202, HSL3203. Replaces HSK3001. MF-6-165

187 7 FORAGE AND HARVESTING Sickle Assemblies Application Sickle Mower: 41, 51, M92 (s/n & up) Welded Gear Box Mower Conditioner: M91 Power Cut 1/4" x 7/8" K Knifeback Replaces Part RIVETED/BOLTED TYPE OF No. SECTION SECTION Riveted Riveted BOLTED "Big Tooth" Sickle Section Designed to last longer and stay sharper than ordinary sickle sections. Ideal for coarser, dryer stem crops (10 serrations per inch). H, US, CR H, US H TS CR LENGTH (FT) 7' 9' 16' INCLUDES NUMBER HEAD NUMBER OF SECTIONS M M1 Headless Universal Chrome End Sections Replaces Section Part No M M K Eliminates dead space at end of cutter bar & prevents clogging. Every 2-pack card of 2US-PK & 3TS-PK has mounting instructions printed on the reverse side. Sections are priced & sold by the piece, but shipped in package multiples only. If sections are packaged 10 per box, please order in multiples of 10 sections (10, 20, etc.). If sections are packaged 2 sections per card, please order in multiples of 2 sections (2, 4, etc.) M2BT Big Tooth section, 10 serrations per inch. H TS CR, 3" x 3-1/4", 2" hole spacing. Used with rigid header #1859. Combines: 510, 540, 550, 750, 850 (prior to s/n ), 860 (prior to s/n ). Can replace M M1BT Big Tooth section, 10 serrations per inch. H TS plain, 3" x 3-1/4". Windrowers: 885 (with auger header). 1S-B Smooth end section, chrome, heavy- duty. Packaged 10 sections per box. Replaces 1SG. 3TS-PK Topserrated end section, chrome, heavy-duty. Packaged 2 sections. Replaces 3TSG. MF-7-166

188 7 FORAGE AND HARVESTING Replacement parts to fit Sickle Sections 3" x 3-1/4" Windrowers: 885 (with auger header) M1 -hvy gauge, top serrated, plain finish, uses RIV101. 3" x 3-1/4" Mowers: 30, 31, 32, 51, 52, 71, 135, FEO, MH5, MH6 (1940 & up) M CR " x 2-1/2" Combines with wobble drive. Floating cutter bar on combines: 750 & 760 (s/n & up) -Hvy. gauge, Top serrated, Chrome finish, uses CR8-5 rivet. For use on combines with wobble drive & floating cutter bars. 3" x 3" Combines: 35, 60, 72, 80, 90, 92, Super 92, 300, 410, 510 (1954 & up) Sickle section, heavy gauge, 3" x 3-3/16" under serrated, chrome finish, uses RIV101 rivet. Regular gauge, 3" x 3-3/16", under serrated, plain finish, uses RIV105 rivet. 3" x 3-3/16" Mowers: AEO-A20, AEO-B20, PEO21, PEOA21 ( ), FEO ( ), MH41, MH60 (1940 & up) M M1 L M M M1 Heavy gauge, under serrated, plain finish, uses RIV101. Heavy gauge, under serrated, chrome finish, uses RIV101. Regular gauge, under serrated, plain finish, uses RIV105. 3" x 3-1/4" Mower Conditioners: 725, 925 Heavy gauge, top serrated, plain finish, uses RIV101. Heavy gauge, under serrated, plain finish, uses RIV101. Section Rivets and Rivet Assortments No. 5-1/2" x 9/16" oval head rivet (1 lb) M1 Heavy gauge, 3" x 3-3/16", smooth edge, plain finish, uses RIV101 rivet. Heavy gauge, under serrated, plain finish, uses RIV101. CR85 Rivets, #5-1/2 x 5/8" countersunk head rivet (1 lb) M CR Regular gauge, under serrated, plain finish, uses RIV105. Regular gauge, 3" x 3-3/16" under serrated, chrome finish, uses RIV105 rivet. RIV66 Packaged assortment of 66 rivets. 1/2" & 7/16" lengths, #5-1/2 oval head section rivets M1 3" x 3-1/4" Combine: 35, 60, 72, 80, 90, 92 Super 92, 300, 410, 510 (1954 & up) Regular gauge, top serrated, chrome finish, uses RIV105. Replaces M2. RIV66H Same as above, except rivets are 9/16" & 15/16" lengths. For heavy sections M2 Heavy gauge, top serrated, chrome finish, uses RIV101. Replaces M1H and M2H. RIV77 Packaged assortment of 77 rivets, 4 lengths, #5-1/2 oval head, for knife head & sections. MF-7-167

189 7 FORAGE AND HARVESTING Sikl-Fix Rivet Vise Sicklehead Parts SF11 KE114A17 KE114A24 KE114A25 KE114A26 KE114A27 KE114A28 Heavier strong frame! Combination rivet-punch & rivet set vise. Removes & replaces sections on all mowers & other knives without removal or teardown of knife or sickle bar. Now has a frame made of higher tensile strength ductile iron. Knockout screw has been lengthened to add frame strength when riveting. Painted red. Sikl-Fix vise. Vise frame Riveting screw, 3/4" THD Riveting screw cup Riveting screw spring Knockout punch Knockout screw M M M M M M1 Dyna-Balance Mowers: 30, 31, 41, 51, 71, 135 Head only, replaces M1. (A) Connector only, for sickle head. (B) Seal for sickle head connector bearing, 2 required. Also used in counterweight except on 41. (C) Needle bearing, for sickle head connector. Replaces M1. (D) Spacer, for sickle head connector bearing. (E) Bolt, has special long shoulder for sickle head connector. (F) Guard & Plow Bolts Tisco supplies coarse thread 7/16"-14 plated bolts, does not include nuts. KE115A28 Knockout screw body, female, 3/4" THD KE116A28 Knockout screw punch holder, 1/2" x 20 THD KE114A1812 Knockout screw punch holder KBSMFC1 Sickle Head Bearing Kit Kit, needle bearing M1 plus 2 seals M1 to repair sickle head on combines: SP300, SP410, SP S36 Bolt, guard & plow. 7/16"-14 x 1-1/2", No. 3 head, use with M91 and M91. Bolt, guard & plow. 7/16"-14 x 1-3/4", No. 3 head, use with M1, M1. Nut, 5/16"-24 x 1/2". Ledger Plates 34670S Nut, 7/16"-14 x 11/16". Nut, 5/8"-18 x 1-1/16" for M1-WNL pin S36 Lock washer, 7/16" S36 Lock washer, 5/8" for M1-WNL pin M1 Use with guards M1, M1, M91, M91, M91, M91. Mowers: Ferguson AEO-A20, AEO-B20, PEO-21 & MH 41 & 60, (1942 & up). MF-7-168

190 7 FORAGE AND HARVESTING Replacement parts to fit DM700 Guards 7/16" bars. Massey Ferguson (LA67 & L215) M1 Stub guard. Windrowers: 725, 925, 885. FD M M M2 For 1/2" bars. Allis Chalmers, Case, Detroit (N12 & 15294), Ferguson, Ford, Massey Ferguson, Oliver, Worthington. Can Replace Massey Ferguson M1. Malleable guard, heavy-duty, center. Replaces M91, M91, M1. Mowers: AEO-A20, AEO-B20, PEO-21 & Massey Harris 41 & 60, (1942 & up). Bar size 1/2", guard plate number M1. Guard, heavy-duty center. Mowers: Regular & Dyna-Balance FEO & Side Mount. Guard plate # M1. Two-prong guard, forged steel, for all combines. Buchanan # BC240A. FLW30 Wearing Plates Universal wear plate. Fits all mowers, combines, and swathers with 3" spacing. Knife Clips K Low knife clip; can replace Massey Ferguson numbers M1, M M M1 Knife clip, high arch type. Mowers: Ferguson AEO-A20, AEO-B20, PEO-21. Knife clip, low arch type. Mowers: PEO-A21, Massey Harris 41, M1 Two-prong guard, forged steel. Combines: 540, 550, 750, 760, 850, 860 (all with floating cutter bar). Buchanan # BU231. Improve Cutting Action With Sic-L-Clip M1 Two-prong guard, forged steel. Hay-Tedder: MF81. Buchanan # BU M M1 BU215H Two-prong guard, forged steel. Windrowers: 35, 655, 675, 775, 875. Buchanan # BU235. Two-prong guard, forged steel. Mower Conditioners: 725, 925. Swathers: 775 (table s/n & up), 885. Buchanan # BU215A. Two-prong guard, double heat treat, forged steel. Mower Conditioners: 725, 925. Swathers: 775 (table s/n & up), 885. Buchanan # BU215BH. Can replace M1. SLC330 SLC331 SLC370 SLC371 SLC400 Use one clip every foot on sickle knife. Saves wear on sections. Steel spring holds sections against ledger plates for improved cutting. 4 models fit most cutter bars. Each model packed 12 per display carton. Standard model for 3/8" bolts. Hi-Clear model for 3/8" bolts. Standard model for 7/16" or 1/2" bolts. Hi-Clear model for 7/16" or 1/2" bolts. Replacement Nylatron wear strip (std. pkg. 25). Mower Pittman Wood M1 Pitman wood, 34" length. Mowers: MF32, MF42, MF52. MF-7-169

191 7 FORAGE AND HARVESTING TIM Mower Bearings Cup: all mowers. Blades for Rotary Disc/Drum Mowers TIM Cone: all mowers M1 Disc mower blade, LH. 4.75" (120.65mm) length, 2" (50.80mm) width,.72" (18.3mm) hole diameter, 11 degree. Disc Mowers: MF M M1 Ball bearing, blade drive shaft housing. For riding mowers: MF626, MF832/8. Replaces 204RPN-2. Needle bearing, 1" bore, 1.25" O.D. For mower spindle shaft on MF610 riding mower. Replaces B M1 Disc mower blade, RH. 4.75" (120.65mm) length, 2" (50.80mm) width,.72" (18.3mm) hole diameter, 11 degree. Disc Mowers: MF127. Spring Teeth & Fingers for Rakes, Balers, Windrowers & Combines Mower Belts M1 Double tine, for five bar pick-up. Balers: 124 & M1 Belt, 105" length. For Dyna-Balance models. Mowers: MF30 wide, MF31, MF41, MF51 (early) M1 Double tine tooth. Balers: 9, 10, 12. Kosch All-Steel Grassboard M1 Used on round balers, Model 1440; 32 teeth used prior to s/n & 40 teeth after same s/n. Model 1560: 40 teeth used prior to s/n & 60 teeth after same s/n. SGB10 Clean sweep all steel board, custom fit to Massey Ferguson mowers M1 Tooth, rubber. Balers: 1440, 1455, 1550, MF-7-170

192 7 FORAGE AND HARVESTING Replacement parts to fit Flat Head Socket Drive Baler Bolts Grade A alloy, zinc plated M1 Tooth, universal reel C5. For use on combines Bolt, flat head socket drive, 1/2"-13 x 1-1/4". For bale chamber shear blade, all balers. H1611 Tooth, Hume reel. For use on combines. Baler Shear Bolts & Nuts Tisco replacement shear bolts & nuts are designed to exacting OEM specifications. For your convenience, shear bolts are priced each, sold in packages of 10 bolts & nuts M2 Shear bolts: 5/16"-24 x 3-1/8", hex head, grade 2, zinc plated. Nuts: 5/16"-24, steel, hex nut, zinc plated M1 Rakes: MH21, 25 (s/n & up) M1 Baler Friction Slip Clutch Disc Friction slip clutch disc, used in slip clutch assemblies. Balers: 450, 560, 1440, 1450, 1550, Skidsteer Loader: /2" O.D., 2-5/8" I.D M M1 Rake tooth for model 20 to s/n Rake tooth for model 36 rake M91 Switch For Twine Tie Activator Switch, electric twine tie activator. Round Balers: 634, 640, 645, 656, 1440, 1455, 1550, 1560, Baler Wire Guide Bearing M1 Rake tooth. Wheel Rakes: MF29 (s/n & up), MF39 (s/n & up). 10" off-set M91 Roller bearing, V-groove for wire guide. Balers: 10, 126, 130, 220, 224, 228 (646311). 1-1/8" O.D., 1/4" I.D M1 Rake tooth. Wheel Rakes: MF29 (to s/n ). 12-1/2" off-set. MF-7-171

193 7 FORAGE AND HARVESTING Bale Counters Bearings For Corn Heads M M2 Left hand pull lever. Balers: 3, 9, 10, 36. Left hand push lever. Balers: 124, 126. Spacer M1 For Corn Heads: 24, 34, 44, 44-0, 54C; 33, 43, 63, 63C; 64, 83; 62, 82; 1134, 1144, 1164; 1143, 1153, 1163, Bearing, spherical ball, snapping roll upper shaft. Replaces RA104RRB M1 Ball bearing, double shielded, snapping roll gear train bearing. 30mm bore. Replaces 206PP, RS Ball bearing, double shielded, snapping roll gear train bearing. 35mm bore. Replaces 207NPP, RS M1 Use this spacer to attach a 1100 series bearing retainer ( M91) to a 44 series gear box (263234M1). For corn head snapping roll bearing retainer 4 spacers required per retainer. Attach with longer bolts (not supplied) 5/16" x 1-3/4" course thread M1 Bearing, double sealed, snapping roll gear train bearing. Replaces RS. Ball bearing. Mfr. ref. # RS, this bearing is used in a variety of locations on combine models 750, 760, 850, 860. Used in sprockets & pulleys. Replaces RS. Needle Bearing For Combine Corn Heads Flute The new Tisco flute is built to exacting specifications of a special abrasion resistant 3/16" steel, red oxide coated. Matches the most recent OEM part M1 Needle bearing. Used on combine corn heads with #263169M92 corn head gear set M2 Flute, for snapping rolls on corn heads, series: 1134, 1144, 1164; 1143, 1153, 1163, Can also replace flutes M91 & M1 on corn heads series: 24, 34, 55, 44-0, 54, 33, 43, 63, 63C, 62, 82; 64, 83; 222, 322, 422; 321, 421, 621. MF-7-172

194 7 FORAGE AND HARVESTING Replacement parts to fit Ear Corn Deflectors Dust Seal M2 Deflector, left or right, for outer or inner units. For corn heads (except low-profile): 24, 33, 34, 43, 44, 44-0, 62, 63, 63C, 64 To s/n , 82, 83 to s/n ; for outer units only on: 1134, 1143, 1144, 1153, 1163, 1164, For low-profile corn heads, outer units only on; 24, 33, 34, 43, 44, 54C, 63, 63C, 64, 83. Gathering Chain For Corn Heads M2 For combine engine air intake. Dust seal, for engine air intake, rotary style (drum shaped screen). Combines: 750 (prior to s/n ), 760 (prior to s/n ), 850, 860. Flex Tines M91 CL2060H Gathering chain: fits corn heads on most late SP combines. Consists of 2060H chain with 8-C6E corn gatherer link spaced every 8th pitch. For corn head models: 24, 34, 44; 33, 43, 63; 62, 82; 64, 84; 222, 322, 422; 321, 421, ; 621; 1134, 1144, 1164; 1143, 1153, 1163, 1183; 540 sweet corn harvester. Connecting And Offset Links For Corn Head Gathering Chain Used with #241090M91 gathering chain or wherever 2060H gathering chain is used. Connecting link, for 2060H chain K Flex tine, for combine reels with teardrop style bats. Length 12". Packed 50 pieces per box K Flex tine, for combine reels with wood bats. Length 12". Packed 50 pieces per box. Tine Bar Bearing M91 MF Tine Bar Bearing. Rakes: 25, 37, 585, /8" OD 2-1/8" overall length 1-1/2" thread length 3/4" thread HL2060H Offset link, for 2060H chain. MF-7-173

195 7 FORAGE AND HARVESTING M M M2 Straw Chopper Knife Kit and Tooth Kits For Hesston manufactured straw choppers designed for various MF combines. Each kit consists of three knives, three bushings, & three bolts. The quantity of knives used per combine ranges from 42 to 54 depending on combine width. Knife set, for straw chopper. Combines: 300 (s/n & up), 510 (s/n & up), 540, 550, 750, 751, 760, 850, 851, 852, 860. Tooth kit, for Hesston manufactured straw choppers. Contains one tooth, bolt, nut, & lock washer. Combines: 300 (s/n & up), 510 (s/n & up), 540, 550, 750, 751, 760, 850, 851, 860. Use with Tisco straw chopper kit M93. Auger Finger Holders Auger finger holder, heavy cast, for 9/16" dia. finger. Crankshaft journal bore 1-1/8" approx. Combines: 300, 510 (with 1859 series table), 550 (with 1859 series table), 750, 751, 760, 850, 851, 860. Grain Header: Auger Fingers & Guides M2 Auger finger for 9/16" ball, 8-1/2" long. Combines: SP300 (with quick attach tables, s/n & up), SP410, SP510. FH8DMH FH8-25DMH M M M M1 Poly finger guide kit, with bolts. Improved replacement for all models using M1 1/2" diameter fingers. Package of 25 of FH8DMH poly finger guides. For 1/2" diameter fingers (bulk pack). Kit, formed poly finger guides (2) with special bolts (4). Improved replacement for models using M2, 9/16" diameter fingers. Replaces CFHKMF916. Package of M91 poly finger guides, with bolts. For 9/16" diameter fingers (bulk pack). Combine Rubber Paddle Blades Made from multi-plied conveyor belting. Easier to install - the blades lay flat. Rubber paddle blade. Combines: 760 & 860. Eight used on grain machines. Not for drive shaft at top. Replaces M2. Rubber paddle blade. Combines: 750, 751PT, 850, 851PT, 852PT. Eight used on grain machines. Not for drive shaft at top. Replaces M2. Rubber paddle blade. Combines: 750, 751PT, 850, 851PT, 852PT. Two used per machine on paddle drive shaft. Replaces M2. MF-7-174

196 7 FORAGE AND HARVESTING Replacement parts to fit Idler Sprockets Combine Slip Clutch & Bushing M M M M M1 Idler sprocket, 8 tooth, CA550 & 2060 chain, 1/2" bore. Most corn heads. Idler sprocket, 17 teeth, 5/8" bore. Used on auger drive idler. Swather: 775, 785. Idler sprocket, for corn head gathering chain. Has 8 teeth, 5/8" dia. bore. Use with CA550 & 2060 chain, also with gathering chain M91. Corn Heads: 1134, 1144, 1164, 1143, 1153, 1163, Idler sprocket, 18 teeth, 5/8" bore. For drive mounting plate on forage box: 114, 116. Idler sprocket, 15 teeth, 1/2" bore. Primarily used on idler tension arm or lower drive roller. Round Balers: 450, 640, 1440, 1450, 1455, 1550, 1560, Combine Wooden Idler Blocks RASC M M M M91 Slip clutch kit, for straw walker & return elevator drives. Combines: MF410, MF510, MF750, MF760. Slip clutch, outer Slip clutch, inner Bushing, 7/8" I.D., 1 O.D. (2 used) Combine Drive Chain Assemblies Pitch indicates distance center to center of roller pins. Double strand #60, 3/4" pitch roller chain, made up of 162 pitches. Corn Heads: 24, 33, 43, 63C, M1 Wooden idler block, used on the cylinder drive, grain elevator, & other applications. Combines: 205, 300, 410, 510 (s/n to ), 540 & /16" O.D., 7/16" I.D., 1-1/8" wide. Wooden Boxings (Bearing) Part number is for one pair of wooden boxings (two bearing halves) with bolts, nuts, & shims M92 Wooden boxings (one pair) with bolts, nuts, & shims. For straw walkers. Combines: 750, 751, 850, M92 Wooden boxings (one pair) with bolts, nuts, & shims. For straw walkers. Combines: 760, 860. MF-7-175

197 7 FORAGE AND HARVESTING Combine Belts The information below is drawn from OEM parts reference and vendor belt interchange data. Serial numbers and other information relating to specific machines are shown in parentheses. Reference is made to applications for machines identified as S/N (early production or for prior serial number machines) or S/N (late production or for late serial number machines) M M M M M M M M M M M M2-D M1-D M M M4-D M4-D M M M M1-D M M2-D M1-D M1-D M M1-D M M1-D M M1-D M M M M M M1-D M1 Application Reel countershaft (s/n 410 & up); (cleaning fan 510 and 550) Reel (s/n 410 & up), grain auger (510 and 550) Return auger and walker Tank unloader Pair, radiator fan (Diesel) pair, radiator fan Pair, shaker shoe Pair, shaker countershaft Pair, radiator fan, gas Fan and shaker shoe. 750, 760 A/C (Frigidaire) Straw chopper, #2, Straw chopper, # (to s/n ), 760 (to s/n ) Return elevator Straw walker Traction drive, 4 speed, upper. 750 (to s/n ) Traction drive, 4 speed, upper & lower. 750 (to s/n ), 850 upper Straw walker Unloader drive Cleaning fan Main drive 760 (air intake), 860 (rotary screen) Cylinder drive Straw chopper, # Straw chopper, # Grain tank unload, auger Main drive Wobble drive Traction drive, upper Reel drive Traction drive, lower, grain Knife drive (refer to OEM guide for s/n breaks) Slinger (aux. cylinder) Straw spreader Hydraulic pump (refer to OEM guide for s/n breaks) Wobble drive Straw chopper, # (prior to s/n ), 760 (prior to s/n ) Alternator, V MF-7-176

198 8 IMPLEMENTS AND BEARINGS Replacement parts to fit Self-Aligning Spherical Ball Bearings With Collars Wide Inner ring bearings designed for extremely dirty & wet conditions - available in non-relubricating & re-lube types. Both extended inner ring (RA & GRA series) and wide inner ring (1100 & G1100 series). Suffixes PPB & RRB indicate double seals & spherical outside diameters for us in housings with same spherical inside surfaces to allow unrestricted self-alignment. Bearings listed will be individually packaged complete with eccentric locking collars and labeled according to numbers ordered. Part numbers are used only for purposes of identification. Replaces M M M M M M M M1 TWAHB8MF M M M1 REF. # (A) (A) (A) (A) (B) (A) (A) (A) (A) (B) (A) (A) (A) BORE SIZE (IN) 1-1/4" 3/4" 1-1/16" 1-3/16" 1-3/8" 1-1/8" 1-1/2" 1-3/8" 1-1/4" 1-1/2" 7/8" 1" 1" Cultivator Gauge Wheels & Related Items Cultivator gauge wheel assembly, for single arm gauge wheels. Contains 2 wheel halves, a bearing, & a 4" x 12" tire. Wheel half, cultivator. Rim diameter 8-5/8", rim width 2". Special sealed ball bearing for cultivator gauge wheel, 2.890" overall length, bearing 1.531" L, shaft 1.198" L x.6267" O.D. Cultivator tire, 4" x 12". OUTER DIA. (IN) " " " " " " " " " " " " " M M1 OUTER DIA. (MM) 62mm 47mm 62mm 62mm 72mm 62mm 80mm 72mm 72mm 80mm 52mm 52mm 52mm Cultivator Washer MFR. REF. NO. RA103RRB2 RA012RRB RA101RRB RA103RRB 1106KRRB RA102RRB RA108RRB RA106RRB RA104RRB 1108KRRB RA014RRB RA100RRB RA100RRB Special cultivator washer, sweep to arm. Special Ball Bearing Special ball bearing with hex bore used on MF54 flail forage harvester & on 260 heavy-duty forage harvester. MF-8-177

199 8 IMPLEMENTS AND BEARINGS Combine Bearings These bearings are used in several combine models with the majority found in combines: 750, 760, 850 & 860. We did not attempt to list specific usage because these bearings have many applications. However, we do list a manufacturer reference number opposite the Massey part number & an example location where each bearing could be used M M M1 Ball bearing. Mfg. number RS. Used in a variety of locations on combines listed above, including table and reel drive. Ball bearing. Mfg. number RS. Used in a variety of locations on combines listed above, including auger. Ball bearing, double shielded, 25mm bore, replaces 305NPP, RS. Ball bearing. Mfg. number RS. Used in a variety of locations on combines listed above, including elevator to table drive Ball bearing, spherical O.D., 20mm bore, replaces 204PPB M1 Ball bearing. Mfg. number RS. Used in a variety of locations on combines listed above, including table and reel drive M M M M M Ball bearing. Mfr. ref. # RS, this bearing is used in a variety of locations on combine models 750, 760, 850, 860. Used in sprockets & pulleys. Ball bearing. Mfg ref. number RS. Used in a variety of locations on combines referenced above. Ball bearing, double shielded, I.D " (25mm), O.D ", W ". Replaces 205PP, RS. Ball bearing. Mfg. number RSQ. Used in a variety of locations on combines listed above, including hydraulic pump drive. Ball bearing, double shielded, 17mm bore. Replaces 203PP, RS. Ball bearing, double shielded, 15mm bore. Replaces 202PP, RS. Ball bearing, double shielded, snapping roll gear train bearing. 30mm bore, replaces 206PP, RS. Ball bearing. Mfg. number RS. Used in a variety of locations on combines listed above, including grain elevator drive. Ball bearing. Mfg. number RS. Used in a variety of locations on combines listed above, including auger. Ball bearing, double shielded, 20mm bore, replaces 204PP-IMP, RS. Ball bearing, double shielded, snapping roll gear train bearing. 35mm bore, replaces 207NPP, RS M M M M M M M M M M1 Ball bearing, double shielded, 50mm bore, replaces 210NPP, 6210-RS. Ball bearing, double shielded, 35mm bore, replaces 307NPP, RS. Ball bearing. Mfg. number 6204-RSJ. Used in a variety of locations on combines listed above, including radiator fan shaft. Ball bearing. Mfg. number RS. Used in a variety of locations on combines listed above, including electric variable speed reel drive. Ball bearing, double shielded, 40mm bore, replaces 308NPP, RS. Ball bearing, spherical O.D., 30mm bore, replaces 206NPPB. Ball bearing. Mfg. number Used in a variety of locations on combines listed above, including cylinder drive. Ball bearing, spherical O.D. 25mm bore, replaces 205PPB. Ball bearing. Mfg. number RS. Used in a variety of locations on combines listed above, including elevator top shaft drive. Needle bearing, replaces B2016. Ball bearing. Mfg. number RS. Used in a variety of locations on combines listed above, including table and reel drive. LM67048L cone with LM67000 seal assembly. Used with cone on combines 35PT & SP, cylinder drive shaft in pulley hub. Corn heads 20 & 22, main auger drive shaft & snapping rolls. Bearing cone, 1.625" I.D.,.78" width. MF-8-178

200 8 IMPLEMENTS AND BEARINGS Replacement parts to fit M M1 Ball bearing. Mfg. number RS. Used in a variety of locations on combines listed above, including cylinder drive. Bearing cup, 2.891" O.D.,.58" width. Popular Disc Copy:Spherical O.D. ball bearings for various disc applications. Manufacture Reference Number M1 Ball bearing. Mfg. number 6018Z. Used in a variety of locations on combines listed above, including cylinder drive M1 Ball bearing, spherical O.D., 15mm bore, replaces 203NPPB M1 Ball bearing. Mfg. number RS. Used in a variety of locations on combines listed above, including grain pan and shaker shaft M M M M M M1 Bearing cone, 1.000" I.D.,.56" width. Bearing cup, 1.98" O.D.,.42" width. Ball bearing. Mfg. number RS. Used in a variety of locations on combines listed above, including rasp bar cylinder. Ball bearing. Mfg. number RS. Used in a variety of locations on combines listed above, including grain elevator drive. Ball bearing, double shielded, special size, 35mm bore, replaces 207KRR3. Ball bearing. Mfg. number 210ZJ. Used in a variety of locations on combines listed above, including grain elevator drive. 6210Z. Replaces M M M M M M PR FAFNIR GW211PPB3 W211PPB3 W208PPB23 W208PPB6 W209PPB5 GW209PPB5 B.C.A. DS211TTR3 DS211TT3 DS208TT2A DS208TT6 DS209TT5 DS209TTR5 NEW DEP. RAS4511BE AS4511BE AS4509B AS4509A RAS4509A Flangette for Self-Aligning Bearings Sold in pairs only. Flangettes, round, non-relube, with 4 holes; for " (80mm) O.D. bearings (F4-80) M M M M M M M M M1 Ball bearing, double shielded, replaces 203KRR2. Ball bearing. Mfg. number RS. Used in a variety of locations on combines listed above, including radiator fan drive. Bearing race (IRA-8), 300 combines various applications. Roller assembly (B1212), 300 combines various applications. Ball bearing. Mfg. number RA100RRB. Used in a variety of locations on combines listed above, including grain elevator drive. Ball bearing. Mfg. number Used in a variety of locations on combines listed above, including elevator to table drive. Needle bearing, knife head on combines: SP300, SP410, SP510. Needle bearing, 1" bore, 1.25" O.D. For auger drive shaft on combines: 410, 510. Replaces B168. Bearing cone, 1.5" I.D.,.72" width PR M2 FTR352 3-bolt round steel flangette used to retain power transmission bearing. O.D " (52mm) used with 7/8", 13/16", 15/16" & 1" bore bearings. For pull-type machines. Combines: 35, 60, 72, 405, 751 & 851. For self-propelled machines Combines: 35, 60, 72, 80, 82, 90, 92, 92 Super, 300, 5. (F3-52) Flangettes, round, non-relube, with 3 holes, for " (62mm) O.D. bearings (F3-62) Flangettes, round, non-relube, with 3 holes, for " (72mm) O.D. bearings (F3-72) Flangettes, triangular, non-relube, for " (52mm) O.D. bearings. Replaces M M1 Bearing cup, " O.D.,.55" width. MF-8-179

201 8 IMPLEMENTS AND BEARINGS Wheel Bearing Kit for Harrows and Plows Tapered Bearing Cups and Cones MF-WBK520 Wheel bearing kit, services one wheel. Disc Harrows: 520, 620, 720, 820. Plows: 43, 345 (with 1-3/4" O.D.) gauge wheel, 370 (reversible) gauge wheel. Chisel Plows: 129 (main wheels & crank type gauge wheel), M M1 Tapered cup (LM603011). Tapered cone (LM603049) M1 Seal M1 Wear sleeve LM29710-TIM Bearing cup LM29749-TIM Bearing cone LM67010-TIM Bearing cup LM67048-TIM Bearing cone MF-8-180

202 8 IMPLEMENTS AND BEARINGS Replacement parts to fit 6000 Series Bearings (Flat Edge) Replaces M1 Reference Number 6010-Z A Bore Dia. (A) " 6200 Series Bearings (Flat Edge) B O.D. (B) " C Width (C) " Bearing Sides 1 shield Replaces M M M M M M M M M M M M M1 Reference Number RS RS RS 16MM RS 6203-ZZ 6203ZZ RS RS RS RS RS 6208Z RS RS 6210Z RS 6210ZZ 6211Z A Bore Dia. (A) " " " " " " " " " 1.378" " " " " " " " " B O.D. (B) " 1.378" " " " " " " " " " " " " " " " 3.937" C Width (C) " " " " " " " " " " " " 0.748" 0.748" " " " " Bearing Sides 2 contact seals 2 contact seals 2 contact seals 2 contact seals 2 shields 2 shields 2 contact seals 2 contact seals 2 contact seals 2 contact seals 2 contact seals 1 shield 2 contact seals 2 contact seals 1 shield 2 contact seals 2 shields 1 shield MF-8-181

203 8 IMPLEMENTS AND BEARINGS 6300 Series Bearings (Flat Edge) Replaces M M M1 Reference Number RS RS RS RS RS RS A Bore Dia. (A) " " " 1.378" " " " B O.D. (B) " " " " " " 3.937" C Width (C) " " 0.748" " " " " Bearing Sides 2 contact seals 2 contact seals 2 contact seals 2 contact seals Open 2 contact seals 2 contact seals MF-8-182

204 9 MISCELLANEOUS Replacement parts to fit M M91R M91 CL621029C0 CL625855C Compressors Air conditioning compressor. Reman A6, 12 Volt 2 o'clock, New 5.58" clutch, Superheat compressor. Superheat switch not included. Tractors: MF1080, MF1085, MF1100, MF1105, MF1130, MF1135, MF1150, MF1155, MF1500, MF1505, MF1800, MF1805, MF2640, MF2675, MF2705, MF2745, MF2775, MF2805, MF3505, MF3525, MF3545, MF4800, MF4840, MF4880, MF4900. Combine: 540, 550, 750, 760, 850, 860. Air conditioning compressor, Reman York - LH suction, Rotolock. Clutch not included. Combine: 510, 8590, 8680, Air conditioning compressor, New York LH suction, Rotolock. Clutch not included. Combine: 510, 8590, 8680, Air conditioning compressor, New York RH suction, Rotolock. Clutch not included. Combine: 510, 8450, Air conditioning compressor, New York RH suction, Tube-O. Clutch not included. Combine: Air conditioning compressor, New Original Sanden - ear mount - SD7H15, 5 1/4" 2-groove clutch, vertical tube o-ring. Tractors: MF9240. Air conditioning compressor, New Original Sanden - ear mount - SD7H15, 5-1/4" 2-groove clutch, horizontal tube - o-ring. Combine: 8680, 8780, M2R M91S M92 Air conditioning compressor, New Aftermarket original Sanden- ear mount - SD7H15, 5-1/2" 2-groove clutch. Tractors: MF366, MF3545, MF3630, MF3645, MF3650, MF3655, MF3660, MF4233, MF4240, MF4243, MF4245, MF4253, MF4255, MF4260, MF4263, MF4265, MF4270, MF5460, MF5470, MF5480, MF6140, MF6150, MF6170, MF6180, MF6190, MF6235, MF6245, MF6255, MF6270, MF6280, MF6290, MF6445, MF6455, MF6460, MF6465, MF6470, MF6475, MF6480, MF6485, MF6490, MF6495, MF6497, MF6499, MF7465, MF7475, MF7480, MF7485, MF7490, MF7495, MF8120, MF8140, MF8150, MF8160, MF8210, MF8220, MF8240, MF8245, MF8250, MF8260, MF8270, MF8280, MF8450, MF8460, MF8470, MF8480. Air conditioning compressor, New compressor. Kit, A6 to Seltec conversion kit. Mounts to original compressor. Kit allows for the use of the original hoses and adapts to original A6 mounting brackets. Tractors: MF1080, MF1085, MF1100, MF1105, MF1130, MF1135, MF1150, MF1155, MF1805, MF2640, MF2675, MF2705, MF2745, MF2775, MF2805, MF3505, MF3525, MF3545, MF4800, MF4840, MF4880, MF4900. Combine: 850. Air conditioning compressor, replacement for Frigidaire A-6 compressor. Includes 5.58" dia. clutch & dust cover, high pressure relief valve. With 12V coil at 10 o-clock, SAE thread. Less superheat switch (comes plugged with non-functional heat switch, new oring & snap ring). MF-9-183

205 9 MISCELLANEOUS Blower Switch Pressure Switches M M M M91 Blower Switch - 3-speed blower switch with knob. Tractors: MF285, MF1085, MF1105, MF1135, MF1155, MF1500, MF1505, MF1800, MF1805, MF3050, MF4800, MF4840, MF4880, MF4900, MF9240. Combine: 750, 760. Thermostatic Switch Thermostatic switch - rotary adjustable, 48" capillary tube, with knob. Tractors: MF150, MF1080, MF1085, MF1100, MF1105, MF1130, MF1135, MF1155, MF1800, MF1805, MF2640, MF2675, MF2705, MF2745, MF2775, MF2805, MF3525, MF3545, MF3505, MF4800, MF4840, MF4880, MF4900, MF6140, MF6150, MF6170, MF6180, MF6190, MF6235, MF6245, MF6255, MF6270, MF6280, MF6290, MF8120, MF8140, MF8150, MF8160, MF8210, MF8220, MF8240, MF8245, MF8250. Thermostatic switch - rotary adjustable, 36" capillary tube. Combine: 8560, 8570, Thermostatic switch. Rotary adjustable, 36" capillary tube. Tractors: MF699, MF670, MF690, MF698, MF660, MF680, MF3050, MF3060, MF3065, MF3070, MF3075, MF3080, MF3090, MF3095, MF3120, MF3120T, MF3125, MF3125 French, MF3140, MF3630, MF3645, MF3650, MF3655, MF3660, MF3670, MF3680, MF3690, MF6140, MF6150, MF6170, MF6180, MF6190, MF6235, MF6245, MF6255, MF6270, MF6280, MF6290, MF8120, MF8140, MF8150, MF8160, MF8210, MF8220, MF8240, MF8245, MF8250, MF8260, MF8270, MF M M M1 Switch HI-LO pressure, Binary switch - 7/16"-2 female flare thread, normally open. Tractors: MF3645, MF3655, MF3660, MF3670, MF3680, MF3690, MF4225, MF4233, MF4235, MF4240, MF4243, MF4245, MF4253, MF4255, MF4260, MF4263, MF4265, MF4270, MF6140, MF6150, MF6170, MF6180, MF6190, MF6235, MF6245, MF6255, MF6270, MF6280, MF6290, MF8120, MF8140, MF8150, MF8160, MF8210, MF8220, MF8240, MF8245, MF8250, MF8260, MF8270, MF8280. Compressor mounted switch - A6 superheat switch. Tractors: MF1080, MF1085, MF1100, MF1105, MF1130, MF1135, MF1150, MF1155, MF1500, MF1505, MF1800, MF1805, MF2640, MF2675, MF2705, MF2745, MF2775, MF2805, MF3525, MF3545, MF3505, MF4800, MF4840, MF4880, MF4900. Combine: 540, 550, 750, 760, 850, 860. High pressure switch - normally closed. Closes 225 psi, opens 375 psi. Tractors: MF9240. Low pressure switch - open - drier mount, normally open. Opens 30 psi, closes 30 psi. Combine: 8560, 8570, 8590, High pressure switch - closed - thermo-disc switch. Opens at 200 F. Combine: 510, 760. MF-9-184

206 9 MISCELLANEOUS Replacement parts to fit MF M M1 Pressure switch kit, compressor mounted. A6 compressor R134 binary pressure switch kit. Tractors: MF1080, MF1085, MF1100, MF1105, MF1130, MF1135, MF1150, MF1155, MF1500, MF1505, MF1800, MF1805, MF2640, MF2675, MF2705, MF2745, MF2775, MF2805, MF4800, MF4840, MF4880, MF4900. Combine: 540, 550, 750, 760, 850, 860. High-Pressure Switch. Normally closed, compressor mount. Replaces red, tan, and dark orange, includes pigtail. Opens 430 psi, closes 200 psi. Tractors: MF4800, MF4840, MF4880, MF4900, MF2640, MF2675, MF2705, MF2745, MF2775, MF2805. Combines: 550, 850, 855, 860, 865, 8570, Limiter Fuse Thermal limiter fuse, compressor mounted switch. Tractors: MF1080, MF1085, MF1100, MF1105, MF1130, MF1135, MF1150, MF1155, MF1500, MF1505, MF1800, MF1805, MF2640, MF2675, MF2705, MF2745, MF2775, MF2805, MF3525, MF3545, MF3505, MF4800, MF4840, MF4880, MF4900. Combine: 550, 750, 760, 850, 855, 860, 865. Receiver Driers M91 2-1/2" diameter receiver drier - 2-1/2" x 8" male o-ring, R12 and R134a compatible. Tractors: MF2675, MF2705, MF2745, MF2775, MF M M M M1 3" diameter receiver drier - 3" x 6" male flare, R12 and R134a compatible. Tractors: MF285, MF1080, MF1085, MF1100, MF1105, MF1130, MF1135, MF1150, MF1155, MF1500, MF1505, MF1800, MF1805, MF4800, MF4840, MF4880, MF4900. Combine: 750, " diameter receiver drier - 3" x 9-1/2" male flare, male switch port. Tractors: MF670, MF690, MF698. 3" diameter receiver drier - 3" x 7" male o-ring, male switch port, R12 and R134a compatible. Tractors: MF365, MF375, MF383, MF390, MF390T, MF393, MF396, MF398, MF399, MF3050, MF3060, MF3065, MF3070, MF3075, MF3080, MF3090, MF3095, MF3120, MF3120T, MF3125, MF3125 French, MF3140, MF3505, MF3525, MF3545, MF3630, MF3645, MF3650, MF3655, MF3660, MF3670, MF3680, MF " diameter receiver drier - 3" x 9" male o-ring, R12 and R134a compatible. Tractors: MF307, MF3050, MF3065, MF3645, MF3655, MF3660, MF3670, MF3690, MF4225, MF4233, MF4235, MF4240, MF4243, MF4245, MF4253, MF4255, MF4260, MF4263, MF4265, MF4270, MF6140, MF6150, MF6170, MF6180, MF6190, MF6235, MF6245, MF6255, MF6270, MF6280, MF6290, MF8120, MF8140, MF8150, MF8160, MF8210, MF8220, MF8240, MF8245, MF8250, MF8260, MF8270, MF8280. MF-9-185

207 9 MISCELLANEOUS M M M W1 3" diameter receiver dries - 3" x 1-1/2" male o-ring, R12 and R134a compatible. Combine: 8680, 8780, Expansion Valves Expansion valve, bulb type - flare - internally equalized with 12" capillary tube, R12 and R134a compatible. Tractors: MF1085, MF1105, MF1135, MF1155, MF1500, MF1505, MF1800, MF1805, MF4800, MF4840, MF4880, MF4900. Combine: 510, 750, 760. Expansion valve, bulb type - flare - externally equalized with 12" tube length, R12 and R134a compatible. Combine: Expansion valve, bulb type - flare - externally equalized with 19" capillary tube, R12 and R134a compatible. Combine: 8560, 8590, Expansion valve, bulb type - o-ring - externally equalized with 14" capillary tube, R12 and R134a compatible. Tractors: MF670, MF690, MF698, MF699, MF2640, MF2675, MF2705, MF2745, MF2775, MF2805, MF3505, MF3525, MF3545. Expansion valve, block valves. R12 and R134a compatible, 1/4" mounting holes. Tractors: MF285, MF3050, MF3060, MF3065, MF3070, MF3075, MF3080, MF3090, MF3095, MF3120, MF3120T, MF3125, MF3125 French, MF3140, MF3630, MF3645, MF3650, MF3655, MF3660, MF3670, MF3680, MF3690, MF6235, MF6245, MF6255, MF6260, MF6265, MF6270, MF6280, MF6290, MF9240. Combine: 850, 855, 860, 865, 8570, M M M91 Expansion valve, block valves. R12 and R134a compatible, 1/4" mounting holes. Tractors: MF4225, MF4233, MF4235, MF4240, MF4243, MF4245, MF4253, MF4255, MF4260, MF4263, MF4265, MF4270, MF6140, MF6150, MF6170, MF6180, MF6190, MF6235, MF6245, MF6255, MF6260, MF6265, MF6270, MF6280, MF6290, MF8120, MF8140, MF8150, MF8160, MF8210, MF8220, MF8240, MF8245, MF8250. Block valves - expansion valve, R12 and R134a compatible. Tractors: MF306, MF3050, MF3645, MF3655, MF3660, MF3670, MF3690, MF6140, MF6150, MF6170, MF6180, MF6190, MF6235, MF6245, MF6255, MF6270, MF6280, MF6290, MF8120, MF8140, MF8150, MF8160, MF8210, MF8220, MF8240, MF8245, MF8250, MF8260, MF8270, MF8280. Expansion valve. O-ring, internally-equalized with 12" capillary tube, R12 and R134A compatible. Tractors: MF374S, MF375, MF383, MF384S, MF390, MF390T, MF393, MF394S, MF396, MF398, MF399, MF2675, MF2705, MF2745, MF2775, MF2805. Combines: 550, 750, 760, 850, 860. MF-9-186

208 9 MISCELLANEOUS Replacement parts to fit Blower Motors M91 Blower motor - double shaft - 12 volt single speed 2 wire motor with 3/8" shafts. Combine: 8560, 8570, M M91 Blower motor - double shaft - 12 volt 3 speed 4 wire motor with 3/8" shafts, heavy duty ball bearing motor. Tractors: MF285, MF1085, MF1105, MF1135, MF1155, MF1500, MF1505, MF1800, MF1805, MF4800, MF4840, MF4880, MF4900, MF9240. Combine: 750, 760, 850, 855, 860, 865. Blower Motor, replacement motor with 5/16" shafts. 12 volt single speed, 2 wire motor. Original replacement motor. Tractors: MF2640, MF2675, MF2705, MF2745, MF2775, MF2805, MF3505, MF3525, MF3545. Blower Assemblies BU10211R MF Bumpers and Mounting Arms Complete, sturdy angle iron grill, same for all models. Mounting arms sold separately for optional applications. Bumper & grill assembly, mounting arms NOT included. Assembly comes painted. Heavy-duty front bumper. Four bars for extra protection. Bumper comes primed. (311541HD) M91 Blower assemblies - blower motor with wheels. 5/16" shaft, 14" overall length, 2.880" motor diameter. 2 spade wires. Tractors: MF3065, MF3070, MF3075, MF3080, MF3090, MF3095, MF3120, MF3120T, MF3125, MF3125 France, MF3630, MF3645, MF3650, MF3655, MF3660, MF3670, MF3680, MF3690, MF6140, MF6150, MF6170, MF6180, MF6190, MF6235, MF6245, MF6255, MF6270, MF6280, MF6290, MF8120, MF8140, MF8150, MF8160, MF8210, MF8220, MF8240, MF8245, MF8250, MF8260, MF8270, MF8280. BU10212R BU10220 Mounting arm, right or left. Tractors: TE20, TO20, TO30, MF35 (axle mount). Two required with BU10211R. Arm comes painted. Mounting arm right or left. Tractors: MF135 (axle mount). 2 required with BU10211R. Arm comes painted. BU1027 Bumper kit, for axle mount. Tractors: MF135. Kit contains 1 - BU10211R grill and 2 - BU10220 mounting arms. Kit components come primed. MF-9-187

209 9 MISCELLANEOUS Emblems M2 Front emblem, includes clips. 6" wing span, 6" nose to tail, 3-5/8" center to center (bolt holes) Painted red. Retaining clip not included. Tractors: MF50, MF65, MF85, MF88, MF97, MF98. Vintage Iron M MPAR M M M1 SNETMF MPAR Front emblem with bracket. 3-3/4" W x 1-1/2" H, 2-1/8" C.C. Includes clips. Ferguson rectangle w/blue background, USA made. Tractors: TO20, TE20, TEA20, TO30. Vintage Iron Side Emblems, Ferguson. Blue background, 1-5/16" H x 9-5/8" W. Includes clips, sold as a pair. Attaches w/3 pegs. Tractors: TO20, TE20, TEA20. Vintage Iron Front emblem. 4-1/2" W x 2-1/2" H, 2" C.C. Includes clips. Ferguson shield w/red background. USA made. Tractors: TO35 (s/n & up). Vintage Iron Front emblem. Die cast (metal). Painted and chromed. Tractors: MF35. Vintage Iron Side emblem, "Ferguson 35". 1-1/4" x 9-7/8". Includes clips. Sold individually. Red background. Attaches w/3 pegs " between pegs. Tractors: TO35, MF35. Vintage Iron Blank engine serial number tag with 4 rivets. Black anodized aluminum " long x 1.885" tall. Customer must stamp number. Tractors: F40, TO35, MF35, MF50, MH50, Early MF135. Industrials: 202, 203, 204, Vintage Iron Side emblem pair, "Massey Ferguson 30". 1-5/16" x 9-5/8". Sold as a pair. Blue background. Attaches w/3 pegs. Tractors: TO30. Vintage Iron M1 SNETTO M M M M1 Front emblem. 4.5" tall, 6.25" long. Tractors: MF50 (Gas / LP, to s/n ), MF65 (Gas / LP / Diesel, to s/n ), MF85, MF88, MF95, MF98, Super 95. Vintage Iron Blank engine serial number tag with 4 rivets. Black anodized aluminum " long x 1.885" high. Customer must stamp numbers. Tractors: TO20, TE20 (w/continental Z120 engine). Vintage Iron Metal Nose Cone Assembly & Replacement Parts Metal nose cone assembly. Contains new style stamped metal nose cone (primed), screen, bar & emblem. Tractors: MF135, MF150, MF165, MF175, MF180. Industrials: 20, 30, 31, 2135, Nose cone comes primed. Replaces M91. Nose cone, metal, less screen, bar & emblem. Tractors: MF135, MF150, MF165, MF175, MF180. Industrials: 20, 30, 31, 2135, Replaces plastic or early style cast metal nose cones. Nose cone comes primed. Screen, black painted steel, for metal or plastic nose cones. Tractors: MF135, MF150, MF165, MF175, MF180. Industrials: 20, 30, 31, 2135, Plastic center nose cone bar with emblem. Tractors: MF135, MF150, MF165, MF175, MF180. Industrials: 20, 30, 31, 2135, Vintage Iron MF-9-188

210 9 MISCELLANEOUS Replacement parts to fit M91 Individual Grill Parts Top grill door. Tractors: MF230, MF235, MF245. Industrial: 20C M91 Front grill door. Tractors: MF150, MF165, MF175. Industrials: 30, 31, MGK M91 Grill kit. Tractors: MF135. Industrials: 20, Center bar & hinge assembly. Tractors: MF40 (late model), MF50, MF M M91 Grill, front. Tractors: TE20, TO20, TO30. Lower Grill Pan. Tractors: TO35 gas (s/n & up), MF35 gas & diesel. Vintage Iron M92 Grill shell. Tractors: MF135. Industrials: 20, M91 Lower grill pan. Tractors: TO35 gas (to s/n ). Vintage Iron M M M M M91 Top grill door. Tractors: MF255, MF265, MF275, MF285. Left grill door, clip-on design for easy access to radiator & air cleaner. Tractors: MF40 (late model), MF50, MF65. Use existing hardware. Right grill door, bolt-on design. Duplicates the OEM part. Tractors: MF40 (late model), MF50, MF65. Use existing hardware. Bottom grill door. Tractors: MF230, MF235, MF245. Industrials: 20C. Front grill door. Tractors: MF135. Industrials: 20, M R M1 Front Grill. Tractors: TO35, MF35. Uses original mounting brackets (not available for purchase). Vintage Iron Front grill screen fastening spring. Secures screen to grill. 4 required, sold individually. Tractors: TE20, TO20, TO30, TO35. Vintage Iron Rubber Hood Trim Rubber hood trim, between grill frame, hood & side panels. 115" long, cut to fit. Tractors: MF230, MF235, MF245, MF255, MF265, MF275, MF285, MF1085, MF1105, MF1135, MF1155. Replaces M1, M1. MGK165 Grill kit. Tractors: MF150, MF165, MF175. Industrials: 30, 31, M91 Bottom grill door. Tractors: MF255, MF265, MF275, MF M93 Grill shell. Tractors: MF150, MF165, MF175. Industrials: 30, 31, MF-9-189

211 9 MISCELLANEOUS Panels & Hood Assemblies (Primed) M1 Bracket assembly for side panel, Right side. Tractors: MF150 (s/n 9A15400 & up), MF165, MF175. Industrials: MF30, MF31, MF M2 Panel, Right side with lamp mounting holes. Tractors: MF135. Industrials: MF20, MF2135. Panel comes primed M92 Hood assembly. Tractors: MF150, MF165, MF175. Industrials: MF30, MF31, MF3165. Hood comes primed M2 Panel, Left side with lamp mounting holes. Tractors: MF135. Industrials: MF20, MF2135. Panel comes primed M91 Panel assembly front, Right side. Tractors: MF230 (prior to s/n 9A243032). Panel comes primed M91 Side panel support assembly. Tractors: MF135. Industrials: MF20, MF M91 Side panel support assembly. Tractors: MF135. Industrials: MF20, MF M91 Panel assembly front, Left side. Tractors: MF230 (prior to s/n 9A243032). Panel comes primed M91 Bracket assembly for side panel, Left side. Tractors: MF150 (s/n 9A15400 & up), MF165, MF175. Industrials: MF30, MF31, MF M92 Panel assembly front, left side. Tractors: MF245. Industrials: MF20C. Panel comes primed. MF-9-190

212 9 MISCELLANEOUS Replacement parts to fit M92 Panel assembly front, right side. Tractors: MF245. Industrials: MF20C. Panel comes primed M91 Hood assembly for tractors with vertical exhaust. Tractors: MF255 (s/n 9A & up), MF265 (s/n 9A & up). Hood comes primed M1 Door assembly, battery. Tractors: MF230 (prior to s/n ), MF235 (prior to s/n 9A229258), MF245 (prior to s/n ), MF265 (prior to s/n ). Industrials: MF20C, MF30B. Door comes primed M91 Hood assembly for tractors with horizontal exhaust. Tractors: MF255 (s/n 9A & up), MF265 (s/n 9A & up), MF275 (s/n 9A & up). Hood comes primed M91 Door assembly, battery. Tractors: MF230 (s/n 9A & up), MF245 (s/n 9A & up), MF265 (s/n 9A & up). Industrials: MF20C, MF30D. Door comes primed M94 Hood assembly, Gas vertical or horizontal exhaust only. Tractors: MF255, MF265. Hood comes primed M1 Panel riser, upper on fenders. Tractors: MF245 (s/n 9A & up), MF255 late production, MF265 (s/n 9A & up), MF275 (s/n & up), MF285 (s/n & up) M1 Panel assembly rear, Left side. Tractors: MF255 (s/n 9A66365 & up), MF265 (s/n 9A66365 & up). Panel comes primed M92 Panel assembly, Right side. Tractors: MF255, MF265, MF275, MF285. Panel comes primed. MF-9-191

213 9 MISCELLANEOUS Fenders Panel comes primed. To install, remove fasteners from old panel & bolt new panel in place. Panel can be shipped U.P.S M92 Panel assembly, Left side. Tractors: MF255, MF265, MF275, MF285. Panel comes primed M1WN Bolt with wing nut, for hood latch assembly & battery tie rod. Tractors: MF35, MF50, MF135. 5/16"-24 x 5" overall M1 Fender panel, dished type, less mounting brackets. For tractors without roll-over protection structure. Tractors: TE20, TO20, TO30, TO35, MF35, F40, MH50, MF50, MF65 (except orchard), MF85 std., MF135 (except vineyard & orchard), MF150, MF165, MF175, MF230, MF235 (except vineyard & orchard), MF245, MF255 (with 16" rims), MF265 std., MF275 std., MF285 std. Industrials: 20 (except turf), 20C (except turf), 30 (except turf), 30B, 35 utility, 40, 50, 50A, 202, 203, 204, 205, 2135 utility, 3165 utility, also these models with 4-post R.O.P.S., 30D, 40B, 50C. Panel comes primed M91 Bolt with special wing nut, for hood latch assembly. Tractors: TO " dia., 5.25" long M92 Hood latch assembly with chrome handle. Tractors: MF20, MF25, MF40, MF50, MF50A, MH50, MF65, MF70, MF85, MF88, MF135, Super 90. Industrials: 202, 203, 204, 205, 302, 304, 356, Vintage Iron M91LR Rear fender, dished type with mounting bracket. For tractors without roll-over protection structure. Tractors: TE20, TO20, TO30, TO35, MF35, F40, MH50, MF50, MF65 (except orchard), MF150, MF165, MF175, MF230, MF235 (except vineyard & orchard), MF245, MF255 (with 16" rims), MF265 std., MF275 std., MF285 std. Industrials: 20 (except turf), 20C (except turf), 30 (except turf), 30B, 35 utility, 40, 50, 50A, 202, 203, 204, 205, 2135 utility, 3165 utility, also these models with 4-post R.O.P.S., 30D, 40B, 50C. Panel comes primed M91 Fender panel assembly, Right side. Tractors: MF135, MF150 (s/n & up), MF165 (s/n 9A & up), MF175, MF180. Industrials: MF30. Fender comes primed. MF-9-192

214 9 MISCELLANEOUS Replacement parts to fit Toolbox M91 Fender panel assembly, Left side. Tractors: MF135, MF150 (s/n & up), MF165 (s/n 9A & up), MF175, MF180. Industrials: MF30. Fender comes primed M1 Toolbox, fits in fender. Tractors: TO35, TE35, MF35, MF40, MF50, MF65, MF135, MF2135. Industrials: 203, 204, 205, 202 Workbull. Vintage Iron CAB INTERIOR KITS Restore your TRACTOR to "NEW" condition Gives cab a "NEW" appearance Safer, quieter, and cleaner cab environment Increases resale value Easy installation with instructions, custom fit technology FMMF1085 Floor mat. Tractors: MF1085, MF1105, MF1135, MF M92 Fender assembly, Left side. Tractors: MF175 (UK). Fender comes primed. Headliner Adhesive M92 Fender assembly, Right side. Tractors: MF175 (UK). Fender comes primed. HLA393 Adhesive, Headliner, trim and laminating. High temperature, Contact-type adhesive, 1-5 min. work time, Unusually high initial or Green strength. MF-9-193

215 9 MISCELLANEOUS Gas Struts Application Strut Tractors: MF550, MF560, MF565, MF575, MF590, MF592, MF595, M1 MF2620, MF2625, MF2640, MF2645, MF2675, MF2680, MF2685, MF2705, MF2720, MF2725, MF2745, MF2775, MF2805. Tractors: MF230, MF231, MF233, MF234C, MF234CF, MF234S, M1 MF235, MF240, MF240S, MF243, MF245, MF250, MF253, MF254, MF254S, MF255, MF260, MF261, MF263, MF263T, MF264T, MF264TCF, MF264TS, MF265, MF273, MF274, MF274C, MF275, MF275E, MF283, MF284, MF284S, MF285S, MF290, MF293, MF294, MF298, MF265, MF342, MF350, MF352, MF355, MF360, MF362, MF365, MF372N, MF375, MF382N, MF390, MF396, MF398, MF399. Tractors: MF3050, MF3055, MF3060, MF3065, MF3065S, MF3070, M2 MF3075, MF3080, MF3085, MF3090, MF3095, MF3115, MF3120, MF3120T, MF3125, MF3140, MF3610, MF3630, MF3635, MF3645, MF3650, MF3655, MF3660, MF3670, MF3680, MF3690. Tractors: MF4215, MF4220, MF4225, MF4225HV, MF4235, MF4240, M1 MF4245, MF4255, MF4260, MF4265, MF4270, MF4315, MF4320, MF4325, MF4335, MF4345, MF4355, MF4360, MF4365, MF4370. Tractors: MF6110, MF6120, MF6130, MF6140, MF6150, MF6160, M1 MF6170, MF6180, MF6190, MF6235, MF6245, MF6255, MF6260, MF6265, MF6270, MF6280, MF6290, MF8110, MF8120, MF8130, MF8140, MF8150, M 8160, MF8170, MF8180, MF8210, MF8220, MF8240, MF8240TRA, MF8250, MF8250TRA, MF8260, MF8260TRA, MF8270, MF8270TRA, MF8280, MF8280TRA. Tractors: MF233, MF253, MF263, MF273, MF283, MF293, MF333, M1 MF353, MF354, MF363, MF363L, MF363S, MF364, MF373, MF374, MF383, MF383S, MF384, MF393, MF394AP, MF3050, MF3055, MF3060, MF3065, MF3065S, MF3070, MF3075, MF3080, MF3085, MF3090, MF3095. Tractors: MF230, MF231, MF233, MF234C, MF235, MF240, MF243, M91 MF244CF, MF245, MF250, MF253, MF254, MF254C, MF255, MF260, MF261, MF263, MF263T, MF264T, MF265, MF273, MF274, MF275, MF283, MF284, MF285, MF290, MF293, MF294, MF298, MF265, MF342, MF350, MF352, MF355, MF360, MF362, MF365, MF372N, MF375, MF382N, MF390, MF396, MF398, MF399. Tractors: MF4215, MF4220, MF4225, MF4235, MF4240, MF4245, M91 MF4255, MF4260, MF4265, MF4270, MF4315, MF4320, MF4325, MF4335, MF4335HV, MF4345, MF4355, MF4360, MF4365, MF4370. Tractors: MF342, MF350, MF352, MF355, MF360, MF362, MF365, M2 MF372N, MF375, MF382N, MF390, MF396, MF398, MF399. Tractors: MF6110, MF6120, MF6130, MF6140, MF6150, MF6160, M3 MF6170, MF6180, MF6190, MF6235, MF6235HV, MF6245, MF6245HV, MF6255, MF6255HV, MF6260, MF6265, MF6270, MF6280, MF6290, MF8110, MF8120, MF8130, MF8140, MF8150, MF8160, MF8170, MF8180, MF8210, MF8220, MF8240, MF8240TRA, MF8250, MF8250TRA, MF8260, MF8260TRA, MF8270, MF8270TRA, MF8280, MF8280TRA. Tractors: MF154, MF174, MF184, MF194, MF233, MF253, MF263, M1 MF273, MF283, MF293, MF333, MF353, MF354AP, MF363, MF364, MF373, MF374, MF383, MF384, MF393, MF394. Type Overall Length Rear Window " Rear Window 19.65" Rear Window " Rear Window " Rear Window 23.11" Rear Window 14.15" Roof Hatch 8.465" Roof Hatch 8.41" Door 9.83" Door 8.84" Door 12.38" Piston Stroke 8.875" 10.22" 13.78" 7.874" " 6.88" 2.756" 4.36" 4.72" 4.32" 6.29" End Type Ball & Socket Clip-on ball joint sockets Ball & Socket Clip-on ball joint sockets Clip-on ball joint sockets Eyelets Steel eyelet and 6mm screw rod end fitting Eyelet and screw rod end Ball & Socket Threaded female ball joint Eyelets MF-9-194

216 9 MISCELLANEOUS Replacement parts to fit Replacement Paint for Massey Ferguson *Additional colors available direct from factory: Flint Gray - fast dry TP320FGAL Massey Harris Brown TP335QT TP230GAL Gray Gallon Massey Harris Red TP340GAL TP340QT TP340SP TP230QT TP230SP Quart Spray Flint Gray Metallic Massey Harris Straw Yellow TP345GAL TP345QT TP345SP TP320GAL TP320QT Gallon Quart Miscellaneous Paint TP320SP Spray Silver Gray TP750GAL Gallon TP750QT MF French Silver Mist Quart TP750SP Massey Ferguson French Silver Mist - spray Red TP300GAL Gallon Satin Black TP300QT Quart TP225GAL Gallon TP300SP Spray TP225QT Quart Industrial Yellow TP225SP Spray TP540GAL Gallon Aluminum TP540QT Quart TP312GAL Gallon TP312QT Quart TP312SP Spray White Gloss TP462GAL Gallon TP462QT Quart TP462SP Spray Black Gloss TP550GAL Gallon TP550QT Quart TP550SP Spray MF-9-195

217 9 MISCELLANEOUS Primer Acrylic Hardner TP2700GAL TP2700QT TP2700SP TP2710GAL TP2710SP TP2720GAL Gray Gallon Quart Spray White Gallon Spray Yellow Gallon TP12HP TP12P Acrylic hardener, lead free. For alkyd gloss tractor and implement enamel, 8 oz. can. Improves initial dry time and hardness development. Use with slow dry alkyd base tractor and implement gloss enamel. Not compatible with fast dry enamel or other paints Acrylic hardener, 16 oz. can, lead free. For alkyd gloss tractor and implement enamel. Improves initial dry time and hardness development. Use with slow dry alkyd base tractor and implement gloss enamel. Not compatible with fast dry enamel or other paints. TP2720QT Quart TP2720SP Spray Red TP3987GAL Gallon TP3987QT Quart TP3987SP Spray MF-9-196

218 9 MISCELLANEOUS Replacement Decals for Massey Ferguson Replacement parts to fit D-MF265 Model MF265. Contains 4 pieces. D-MF135 Model MF135. Contains 6 pieces. D-MF275 Model MF275. Contains 4 pieces. D-MF165 Model MF165. Contains 6 pieces. D-MF290 Model MF290. Contains 4 pieces. D-MF240 Model MF240. Contains 2 pieces. D-MF35 Model MF35. Contains 5 pieces. D-MF245H Model 245. Contains 4 pieces. D-MF35 Model MF35. Contains 5 pieces. D-MF255H Model 255. Contains 4 pieces. D-MF M1 Model MF65. Contains 5 pieces. Hood emblem, Massey Ferguson triangle. Tractors: MF35, MF35, MF65. MF-9-197

219 9 MISCELLANEOUS Seat Assembly Seat Cushions & Backrests M96 One piece black seat assembly with vinyl cover formed over foam cushion on a steel frame. Has holes for drainage & welded on mounting brackets. Replaces M91 thru M95. Tractors: MF135, MF230, MF235, MF245, MF255, MF265, MF275, MF285. Industrials: 20C, 30B, 30D, 40B, 50C & 50D. Seat Cushion for Combines BR204 MFCC12 Complete backrest assembly. Gray vinyl with red trim, 2" foam with holes and wing nuts for easy mounting and height adjustment. Tractors: TEA20, TE20, TO20, MF25, MF30, TO30, MF31, MF35, TO35, MF35, MF50, MF50A, MF65, MF85, MF88, MF98, MF135, MF150, MF178, MF185, MF230, MF235, MF240, MF245, MF250, MF283. Industrials: MF20C, MF20D, MF30, MF40. Complete seat cushion assembly. Gray vinyl with red trim, 4-1/2" foam and attached strap to fasten seat cushion under frame. Tractors: TEA20, TE20, TO20, MF25, MF30, TO30, MF31, MF35, TO35, MF35, MF50, MF50A, MF65, MF85, MF88, MF98, MF135, MF150, MF178, MF185, MF230, MF235, MF240, MF245, MF250, MF283. Industrials: MF20C, MF20D, MF30, MF40. JT77B Seat cushion, black (19-1/2" x 14-5/8"). Durable weatherproof black leatherette cover, steel corners. FC810 Seat cushion and backrest assembly complete. Consists of one BR204 & MFCC12. Gray with red trim. Tractors: TEA20, TE20, TO20, MF25, MF30, TO30, MF31, MF35, TO35, MF35, MF50, MF50A, MF65, MF85, MF88, MF98, MF135, MF150, MF178, MF185, MF230, MF235, MF240, MF245, MF250, MF283. Industrials: MF20C, MF20D, MF30, MF40. BR205 Complete backrest assembly. Black vinyl with black trim, 2" foam with holes and wing nuts for easy mounting and height adjustment. Tractors: MF35, MF50, MF60, MF135, MF140, MF235, MF245, MF250, MF283, MF303E, MF1030. Industrials: MF202, MF203, MF204, MF3357. MFCC13 Complete seat cushion assembly. Black vinyl with black trim, 4-1/2" foam and attached strap to fasten seat cushion under frame. Tractors: MF35, MF50, MF60, MF135, MF140, MF235, MF245, MF250, MF283, MF303E, MF1030. Industrials: MF202, MF203, MF204, MF3357. FC811 Seat cushion and backrest assembly complete. Consist of one BR205 & MFCC13. Black vinyl with black trim. Tractors: MF35, MF50, MF60, MF135, MF140, MF235, MF245, MF250, MF283, MF303E, MF1030. Industrials: MF202, MF203, MF204, MF3357. MF-9-198

220 9 MISCELLANEOUS Replacement parts to fit Complete Seat Cushions, Backrest Inlays, & Covers Three-Pieces Seat Assembly for MF1100, MF M M M M M92 Fits all models with Keystone seats Cushion assembly, gray. Tractors: MF150, MF165, MF175, MF180, MF1080. Cushion cover, grey. Fits all models with keystone seats. Zippered to form fit the old cushion. Has bottom strap for multiple application. Tractors: MF150, MF165, MF175, MF180 & MF1080 (early production models). Formed backrest, grey. 23-1/8" bolt centers. Fits all models with keystone seats. Tractors: MF150, MF165, MF175, MF180 (early production). Formed backrest, grey. 21-7/8" bolt centers. Tractors: MF150, MF165, MF175, MF180 (late production). Formed backrest, black. Tractors: MF50 (s/n & up), MF65 (s/n & up), and MF150, MF165, MF175, MF180 (all with s/n 9A & up); MF255, MF265, MF275, MF285. Industrials: 31. Replaces M M M M M M1 Upper backrest. Tractors: MF1100, MF1130 Wrap around arm rest. Tractors: MF1100, MF1130. Seat cushion. Tractors: MF1100, MF1130 Seat Parts Bucket seat pan (metal). Tractors: 35, 40, MF35, MF50, MF65 Utility, MF85, MF88, MF95, MF130, MF135, MF150, MF180, MF230, MF235. Industrial: 30. Seat spring. Tractors: TE20, TEA20, TO20, TO30, FE35, F40, MF35, F40, F50. Massey Ferguson Seat Riser M92 Seat cushion assembly, black. Tractors: MF50 (s/n & up), MF65 (s/n & up), MF150, MF165, MF175, MF180 (all with s/n 9A & up); MF255, MF265, MF275, MF285. Industrials: 31. Replaces M M M93 Seat riser, for mounting TISCO suspension seats TS1050 and TS1050AT. Use if additional clearance is needed between seat base and lift linkage when seat is moved to most rearward position. Can also be used as replacement riser for OEM production seats. Tractors: MF240, MF290, MF298. Industrials: 40E, 50E. MF-9-199