LSHT Torqmotors and Nichols Motors 110A Series / Serie / Série. Technical Information /Technische Information / Segni / Informacion Tecnica
|
|
- Janice Campbell
- 6 years ago
- Views:
Transcription
1 Technical Information /Technische Information / Segni / Informacion Tecnica 9 Displacements ( in 3 /rev) 9 Schluckvolumen cm 3 /rev 9 Cylindrée 9 Despazamientos Cont Int Maximum Pressure (25 psid) (3 psid) Eingangsdruck Pression entrée Presion Maxima 11 Series / Serie / Série When the Ultimate in Efficiency and Reliability is a Must HY /US,EU This high performance motor contains a power element that is pressure loaded against internal leakage for high volumetric efficiency. It is wear compensated, so that its volumetric efficiency will not degrade with use. It can provide up to 5215 lb-in of torque through a one-piece solid fixed axis shaft. This shaft design allows for full stationary spline contact between shaft and rotor, minimizing spline contact stresses. It also allows the shaft to be extended through the rear cover for mounting parking brakes, auxiliary drive functions or encoders for speed readout or closed loop control. Low internal pressure drop means high mechanical efficiency and higher flow capability. This rugged motor is the most compact on the market. Maximum Oil Flow Schluckstrom Débit d huile Caudal Maximo de ceite Maximum Speed Drehzahl Vitesse de rotation Velocidad Maxima (3 gpm) lpm 858 rpm Cont Int Maximum Torque (4164 lb in) (5215 lb in) Max Drehmoment 47 Nm 589 Nm Couple Torque Maximo Maximum Side Load at Key Seitenlast Charges latèrales Carga Maxima Lateral (145 lb) 645 N 267 Parker Hannifin Corporation
2 Ordering Information / Bestellschlüssel System de Commande / Imformacion para pedidos 11 Series / Serie / Série HY /US,EU 11 Series X Shaft Welle rbre Ejes Engineering Design technischer Entwurf Conception technique Diseño de ingeniería XXX Displacement Schluckvolumen Cylindrée Desplazamiento X Mounting Gehäuse Carter Montaje X Ports nschluß Plan de raccordement Lumbreras X Thru-Shaft durchgehende Welle arbre traversant Eje pasante X X Shaft Material Cross-Over Wellenmaterial Relief Valve Matériel d'arbre Bremslüftventil Material del eje Soupape de sûreté transversale Paint Válvula de alivio transversal X Code 1" Keyed Code SE 2-Bolt, Manifold " 6B Spline 25mm Keyed 1-1/4" Keyed 1-1/4"-14 Tooth Spline cm³/u cm³/tr Code cm³/giro in³/rev / / / / / / / / / 24.1 M S P BM SE 2-Bolt, 7/8"-14 SE SE 2-Bolt, 1/2"-14 NPTF SE B 2-Bolt, Manifold 5 SE B 2-Bolt, 7/8"-14 SE 7/8"-13 Tooth Spline BS 6 Code No Thru Shaft 1 Thru Shaft E Encoder Mount Code Omit S If Not Required Stainless Steel Code Omit R1 If Not Required Cross-Over Relief Valve Consult factory for other available options, configurations ordering codes and lead times. Code Omit F No Paint Black Paint Schwarz lackiert 268 Parker Hannifin Corporation
3 Performance Data / Leistungsdaten Puissance / Datos Tecnicos 11 Series / Serie / Série HY /US,EU Motor Series 11 cm 3 /rev in 3 /rev Geometric displacement Geom. Schluckvolumen Cylindrée Cilindrata rev/min cont / int* l/min g/min Max. differential pressure Max. Druckgefälle Chute de pression maxi Presion diferencial maxima Max. Max. intermittent flow Max. Drehzahl Intermittierender Betrieb: Vitesse de rotation maxi Velocidad maxima a caudal intermitente maximo Max. oil flow Max. Schluckstrom Débit d huile maxi Portata max cont / int* psid max psig Max. supply pressure Max. Eingangsdruck Pression maxi entrée Presion maxima de alimentacion cont / int* Nm lb-in Max. torque Max. Drehmoment Couple maxi Torque Maximo max KW HP Max. performance Max. Leistungabgabe Puissance de sortie maxi Maximo rendimento Performance data based on tests using 15W4 oil with a viscosity of 55 cst (215 SUS) at 54 C (13 F.) Performance data is typical. ctual data may vary slightly from one production motor to another. Les donnees sur les performances sont basees sur des tests utilisant de l huile 15W4 d une viscosite de 55 cst (215 SUS) a 54 C (13 F). Ces donnees correspondent a des situations typiques. Les donnees reelles peuvent varier legerement d un moteur de production a l autre. Leistugsdaten sind gemessen mit SE 15W4 bei einer Viskositaet von 43,1 Cst beo 54 C. Geringfuegige bweichungen von den Katalogerten sond moeglich. Datos tecnicos obtenidos con aceite 15W4 de 55 cst (215 SUS) de viscosidad a 54 C (13 F). Los datos proporcionados son valores tipcos. Los valores exactos reales podrian tener una pequena variacion entre distintos motores. * Intermittent operation rating applies to 1% of every minute. Intermittierende Werte maximal 1% von jeder Betriebsminute. Fonctionnement interm. 1% max. de chaque minute d`utilisation. Capacidad de funcionamiento intermitente valida para 1% por cada minuto. 269 Parker Hannifin Corporation
4 Performance Data / Leistungsdaten Puissance / Datos Tecnicos 11 Series / Serie / Série HY /US,EU cu in / rev 59 cc / rev PRESSURE (PSID) FLOW (GPM) Drehmoment [Nm] Schluckstrom [L/min] Drehzahl [1/min] TORQUE (LB IN) 1664 SPEED (RPM) cu in / rev FLOW (GPM) PRESSURE (PSID) Drehmoment [Nm] 89 cc / rev TORQUE (LB IN) 2491 SPEED (RPM) 566 Schluckstrom [L/min] Cont. Drehzahl [1/min] Cont. with no side load Int. with rated side load Intermittent operation rating applies to 1% of every minute. Intermittierende Werte maximal 1% von jeder Betriebsminute. Fonctionnement interm. 1% max. de chaque minute d`utilisation. Capacidad de funcionamiento intermitente valida para 1% por cada minuto. Performance data based on tests using 15W4 oil with a viscosity of Leistugsdaten sind gemessen mit SE 15W4 bei einer Viskositaet von 43,1 Cst 55 cst (215 SUS) at 54 C (13 F.) Performance data is typical. ctual data beo 54 C. Geringfuegige bweichungen von den Katalogerten sond moeglich. may vary slightly from one production motor to another. Datos tecnicos obtenidos con aceite 15W4 de 55 cst (215 SUS) de viscosidad Les donnees sur les performances sont basees sur des tests utilisant de l huile a 54 C (13 F). Los datos proporcionados son valores tipcos. Los valores 15W4 d une viscosite de 55 cst (215 SUS) a 54 C (13 F). Ces donnees exactos reales podrian tener una pequena variacion entre distintos motores. correspondent a des situations typiques. Les donnees reelles peuvent varier legerement d un moteur de production a l autre. 27 Parker Hannifin Corporation Int.
5 Performance Data / Leistungsdaten Puissance / Datos Tecnicos 11 Series / Serie / Série HY /US,EU cu in / rev PRESSURE (PSID) FLOW (GPM) TORQUE (LB IN) 71 SPEED (RPM) 79 Drehmoment [Nm] 116 cc / rev Schluckstrom [L/min] Drehzahl [1/min] Intermittent operation rating applies to 1% of every minute. Fonctionnement interm. 1% max. de chaque minute d`utilisation. Performance data based on tests using 15W4 oil with a viscosity of 55 cst (215 SUS) at 54 C (13 F.) Performance data is typical. ctual data may vary slightly from one production motor to another. Les donnees sur les performances sont basees sur des tests utilisant de l huile 15W4 d une viscosite de 55 cst (215 SUS) a 54 C (13 F). Ces donnees correspondent a des situations typiques. Les donnees reelles peuvent varier legerement d un moteur de production a l autre. Cont. with no side load Cont. Int. Int. with rated side load Intermittierende Werte maximal 1% von jeder Betriebsminute. Capacidad de funcionamiento intermitente valida para 1% por cada minuto. Leistugsdaten sind gemessen mit SE 15W4 bei einer Viskositaet von 43,1 Cst beo 54 C. Geringfuegige bweichungen von den Katalogerten sond moeglich. Datos tecnicos obtenidos con aceite 15W4 de 55 cst (215 SUS) de viscosidad a 54 C (13 F). Los datos proporcionados son valores tipcos. Los valores exactos reales podrian tener una pequena variacion entre distintos motores. 271 Parker Hannifin Corporation
6 Performance Data / Leistungsdaten Puissance / Datos Tecnicos 11 Series / Serie / Série HY /US,EU cu in / rev PRESSURE (PSID) FLOW (GPM) Drehmoment [Nm] 144 cc / rev TORQUE (LB IN) 451 SPEED (RPM) 458 Schluckstrom [L/min] Drehzahl [1/min] Cont. Cont. with no side load Int. with rated side load Intermittent operation rating applies to 1% of every minute. Intermittierende Werte maximal 1% von jeder Betriebsminute. Fonctionnement interm. 1% max. de chaque minute d`utilisation. Capacidad de funcionamiento intermitente valida para 1% por cada minuto. Performance data based on tests using 15W4 oil with a viscosity of Leistugsdaten sind gemessen mit SE 15W4 bei einer Viskositaet von 43,1 Cst 55 cst (215 SUS) at 54 C (13 F.) Performance data is typical. ctual data beo 54 C. Geringfuegige bweichungen von den Katalogerten sond moeglich. may vary slightly from one production motor to another. Datos tecnicos obtenidos con aceite 15W4 de 55 cst (215 SUS) de viscosidad Les donnees sur les performances sont basees sur des tests utilisant de l huile a 54 C (13 F). Los datos proporcionados son valores tipcos. Los valores 15W4 d une viscosite de 55 cst (215 SUS) a 54 C (13 F). Ces donnees exactos reales podrian tener una pequena variacion entre distintos motores. correspondent a des situations typiques. Les donnees reelles peuvent varier legerement d un moteur de production a l autre. 272 Parker Hannifin Corporation Int.
7 Performance Data / Leistungsdaten Puissance / Datos Tecnicos 11 Series / Serie / Série HY /US,EU cu in / rev PRESSURE (PSID) FLOW (GPM) 174 cc / rev 5 45 TORQUE (LB IN) 519 SPEED (RPM) 229 Schluckstrom [L/min] Drehmoment [Nm] Drehzahl [1/min] Intermittent operation rating applies to 1% of every minute. Fonctionnement interm. 1% max. de chaque minute d`utilisation. Performance data based on tests using 15W4 oil with a viscosity of 55 cst (215 SUS) at 54 C (13 F.) Performance data is typical. ctual data may vary slightly from one production motor to another. Les donnees sur les performances sont basees sur des tests utilisant de l huile 15W4 d une viscosite de 55 cst (215 SUS) a 54 C (13 F). Ces donnees correspondent a des situations typiques. Les donnees reelles peuvent varier legerement d un moteur de production a l autre. 273 Cont. Cont. with no side load Int. with rated side load Parker Hannifin Corporation Int. Intermittierende Werte maximal 1% von jeder Betriebsminute. Capacidad de funcionamiento intermitente valida para 1% por cada minuto. Leistugsdaten sind gemessen mit SE 15W4 bei einer Viskositaet von 43,1 Cst beo 54 C. Geringfuegige bweichungen von den Katalogerten sond moeglich. Datos tecnicos obtenidos con aceite 15W4 de 55 cst (215 SUS) de viscosidad a 54 C (13 F). Los datos proporcionados son valores tipcos. Los valores exactos reales podrian tener una pequena variacion entre distintos motores.
8 Performance Data / Leistungsdaten Puissance / Datos Tecnicos 11 Series / Serie / Série HY /US,EU cu in / rev PRESSURE (PSID) FLOW (GPM) Drehmoment [Nm] TORQUE (LB IN) 618 SPEED (RPM) cc / rev Schluckstrom [L/min] Drehzahl [1/min] Cont. Cont. with no side load Int. with rated side load Intermittent operation rating applies to 1% of every minute. Intermittierende Werte maximal 1% von jeder Betriebsminute. Fonctionnement interm. 1% max. de chaque minute d`utilisation. Capacidad de funcionamiento intermitente valida para 1% por cada minuto. Performance data based on tests using 15W4 oil with a viscosity of Leistugsdaten sind gemessen mit SE 15W4 bei einer Viskositaet von 43,1 Cst 55 cst (215 SUS) at 54 C (13 F.) Performance data is typical. ctual data beo 54 C. Geringfuegige bweichungen von den Katalogerten sond moeglich. may vary slightly from one production motor to another. Datos tecnicos obtenidos con aceite 15W4 de 55 cst (215 SUS) de viscosidad Les donnees sur les performances sont basees sur des tests utilisant de l huile a 54 C (13 F). Los datos proporcionados son valores tipcos. Los valores 15W4 d une viscosite de 55 cst (215 SUS) a 54 C (13 F). Ces donnees exactos reales podrian tener una pequena variacion entre distintos motores. correspondent a des situations typiques. Les donnees reelles peuvent varier legerement d un moteur de production a l autre. 274 Parker Hannifin Corporation Int.
9 Performance Data / Leistungsdaten Puissance / Datos Tecnicos 11 Series / Serie / Série HY /US,EU cu in / rev PRESSURE (PSID) FLOW (GPM) TORQUE (LB IN) 6758 SPEED (RPM) 125 Drehmoment [Nm] 269 cc / rev Schluckstrom [L/min] Drehzahl [1/min] Intermittent operation rating applies to 1% of every minute. Fonctionnement interm. 1% max. de chaque minute d`utilisation. Performance data based on tests using 15W4 oil with a viscosity of 55 cst (215 SUS) at 54 C (13 F.) Performance data is typical. ctual data may vary slightly from one production motor to another. Les donnees sur les performances sont basees sur des tests utilisant de l huile 15W4 d une viscosite de 55 cst (215 SUS) a 54 C (13 F). Ces donnees correspondent a des situations typiques. Les donnees reelles peuvent varier legerement d un moteur de production a l autre. 275 Cont. Cont. with no side load Int. with rated side load Parker Hannifin Corporation Int. Intermittierende Werte maximal 1% von jeder Betriebsminute. Capacidad de funcionamiento intermitente valida para 1% por cada minuto. Leistugsdaten sind gemessen mit SE 15W4 bei einer Viskositaet von 43,1 Cst beo 54 C. Geringfuegige bweichungen von den Katalogerten sond moeglich. Datos tecnicos obtenidos con aceite 15W4 de 55 cst (215 SUS) de viscosidad a 54 C (13 F). Los datos proporcionados son valores tipcos. Los valores exactos reales podrian tener una pequena variacion entre distintos motores.
10 Performance Data / Leistungsdaten Puissance / Datos Tecnicos 11 Series / Serie / Série HY /US,EU cu in / rev 31 cc / rev PRESSURE (PSID) FLOW (GPM) Drehmoment [Nm] TORQUE (LB IN) 2724 SPEED (RPM) 286 Schluckstrom [L/min] Drehzahl [1/min] Cont. Cont. with no side load Int. with rated side load Intermittent operation rating applies to 1% of every minute. Intermittierende Werte maximal 1% von jeder Betriebsminute. Fonctionnement interm. 1% max. de chaque minute d`utilisation. Capacidad de funcionamiento intermitente valida para 1% por cada minuto. Performance data based on tests using 15W4 oil with a viscosity of Leistugsdaten sind gemessen mit SE 15W4 bei einer Viskositaet von 43,1 Cst 55 cst (215 SUS) at 54 C (13 F.) Performance data is typical. ctual data beo 54 C. Geringfuegige bweichungen von den Katalogerten sond moeglich. may vary slightly from one production motor to another. Datos tecnicos obtenidos con aceite 15W4 de 55 cst (215 SUS) de viscosidad Les donnees sur les performances sont basees sur des tests utilisant de l huile a 54 C (13 F). Los datos proporcionados son valores tipcos. Los valores 15W4 d une viscosite de 55 cst (215 SUS) a 54 C (13 F). Ces donnees exactos reales podrian tener una pequena variacion entre distintos motores. correspondent a des situations typiques. Les donnees reelles peuvent varier legerement d un moteur de production a l autre. 276 Parker Hannifin Corporation Int.
11 Performance Data / Leistungsdaten Puissance / Datos Tecnicos 11 Series / Serie / Série HY /US,EU cu in / rev PRESSURE (PSID) FLOW (GPM) Drehmoment [Nm] TORQUE (LB IN) 5169 SPEED (RPM) cc / rev Schluckstrom [L/min] Drehzahl [1/min] Intermittent operation rating applies to 1% of every minute. Fonctionnement interm. 1% max. de chaque minute d`utilisation. Performance data based on tests using 15W4 oil with a viscosity of 55 cst (215 SUS) at 54 C (13 F.) Performance data is typical. ctual data may vary slightly from one production motor to another. Les donnees sur les performances sont basees sur des tests utilisant de l huile 15W4 d une viscosite de 55 cst (215 SUS) a 54 C (13 F). Ces donnees correspondent a des situations typiques. Les donnees reelles peuvent varier legerement d un moteur de production a l autre. 277 Cont. Cont. with no side load Int. with rated side load Parker Hannifin Corporation Int. Intermittierende Werte maximal 1% von jeder Betriebsminute. Capacidad de funcionamiento intermitente valida para 1% por cada minuto. Leistugsdaten sind gemessen mit SE 15W4 bei einer Viskositaet von 43,1 Cst beo 54 C. Geringfuegige bweichungen von den Katalogerten sond moeglich. Datos tecnicos obtenidos con aceite 15W4 de 55 cst (215 SUS) de viscosidad a 54 C (13 F). Los datos proporcionados son valores tipcos. Los valores exactos reales podrian tener una pequena variacion entre distintos motores.
12 Radial Load / Radiale Wellenbelastung Charges Radiale / Carga Radial 11 Series / Serie / Série HY /US,EU Radial Load - N (lb) (3) (25) 8896 (2) 6672 (15) 4448 () 2224 (5) Torque nm (lb-in) () (2) (3) (4) (5) -5.8 (-2) (-1) () 25.4 (1) 5.8 (2) 76.2 (3) Distance From Mounting Face - mm (in) The allowable side load curve is based on L 1 bushing life of 3 x 1 6 RPM. Die zulassige radiale Wellenbelastung bezieht sich auf die Lager-Lebensdauer 3 x 1 6 Umdrehungen. L effort radial admissible sur l arbre depend a une duree de vie 3 x 1 6 de rotation. La curva de carga lateral admisible se basa en vida util de cojinete de 3 x 1 revoluciones. Equation to Calculate the Expected Radial Bearing Life Gelichung zur Ermittlung der Lagerlebensdauer Equation to calculate the dynamic bearing life for a given load: Bestimmung der erlaubten radialen Wellenbelastung mit vorgegebener Last Use F a, F b and S in equation to determine hours of L 1 bearing life. Die Lebensdauer in Stunden ergibt sich durch einsetzen von F a, F b, und S in die nachstehende Formel. L = 3. x 1 6 { Fa } x S F b Where / Mit: S = Shaft Speed RPM / btriebswellendrehzahl in min -1 L = Life In Hours / Lebensdauer in Stunden F a = llowable side load defined by above curve at a distance from mounting flange. / Erlaubte radiale Wellenbelastung als Function der Laenge F b = pplication side load. / nwendungsseitige Wellenbelastung Note: Calculations are based on L 1 bearing life per ISO 281. uslegung basiert auf einer L 1 Lenbendauer nach ISO Parker Hannifin Corporation
13 Mounting,Ports/Gehäuse,nschlüße Carter,Orifices / Montaje,Lumbreras 11 Series / Serie / Série HY /US,EU Code: M SE 2-Bolt, Manifold Ø (4.5) 15.7 (.62) "L" B 28.5 (1.12) 11.2 (.44) 3.1 (.12) 2 x 14.2 (.56) 2x 31.8 (1.25) Ø (3.25) (.95) B 2X 14.2 (.56) 13.3 (5.13) Max 16.4 (4.188) 7/16-2 STRIGHT THD O-RING CSE DRIN ø 2.62 (.812) x 2.3 (.8) Deep Motor with manifold mount is supplied with 2 O-rings. Zum Motor mit Universalanschluß werden 2 O-Ringe geliefert. Deux joints toriques sont livrés avec les moteurs a plan de raccordement universel. Il blocchetto connessioni é corredato da 2 OR. 2 X (1.255) 2x 22.9 (.9) 4x 5/16-18 UNC-2B x 12.7 (.5) Min Full Thread O-rings 2.62 (.812) (.95) 59.9 (2.36) 58.5 (2.35) For Manifold 117.1(4.61) (4.55) For Manifold Code M Weight/Gewicht kg Poids/Peso (lb) (15.4) (16.2) (16.9) (17.5) (18.4) (19.1) (2.6) (21.6) ( 23.7) Length "L" mm "L" (in) (4.41) (4.6) (4.78) (4.98) (5.17) (5.42) (5.8) (6.7) (6.64) 2.3 (.8) Code: S SE 2-Bolt, 7/8"-14 SE O-Ring Ø (4.5) 15.7 (.62) "L" B 28.5 (1.12) 11.2 (.44) 3.1 (.12) 2 x 25.4 (1.) Ø (3.25) (.95) B 2X 14.2 (.56) 13.3 (5.13) Max 16.4 (4.188) 7/16-2 STRIGHT THD O-RING CSE DRIN 7/8-14 SE O-Ring 2 X (1.255) (.95) 59.9 (2.36) 58.5 (2.35) For Manifold 117.1(4.61) (4.55) For Manifold Code S Weight/Gewicht kg Poids/Peso (lb) (15.4) (16.2) (16.9) (17.5) (18.4) (19.1) (2.6) (21.6) (23.7) Length "L" mm "L" (in) (4.41) (4.6) (4.78) (4.98) (5.17) (5.42) (5.8) (6.7) (6.64) English equivalents for metric specifications are shown in ( ). 279 Parker Hannifin Corporation
14 Mounting,Ports/Gehäuse,nschlüße Carter,Orifices / Montaje,Lumbreras 11 Series / Serie / Série HY /US,EU Code: P SE 2-Bolt, 1/2" BSPP Ø (4.5) 15.7 (.62) "L" B 28.5 (1.12) 11.2 (.44) 3.1 (.12) 2 x 25.4 (1.) Ø (3.25) (.95) B 2X 14.2 (.56) 13.3 (5.13) Max 16.4 (4.188) 7/16-2 STRIGHT THD O-RING CSE DRIN 1/2-14 NPTF 2 X (1.255) (.95) 59.9 (2.36) 58.5 (2.35) For Manifold 117.1(4.61) (4.55) For Manifold Code T Weight/Gewicht kg Poids/Peso (lb) (15.4) (16.2) (16.9) (17.5) (18.4) (19.1) (2.6) (21.6) ( 23.7) Length "L" mm "L" (in) (4.41) (4.6) (4.78) (4.98) (5.17) (5.42) (5.8) (6.7) (6.64) Code: BM SE B 2-Bolt, Manifold Ø (4.5) "L" B 29.2 (1.15) 14. (.55) 6.4 (.25) 15.7 (.62) 2 x 14.2 (.56) 2x 31.8 (1.25) Ø (3.999) (.95) B 2X 14.2 (.56) (5.66) 176. (6.93) Max 7/16-2 STRIGHT THD O-RING CSE DRIN ø 2.62 (.812) x 2.3 (.8) Deep 2 X (1.255) 2x 22.9 (.9) 4x 5/16-18 UNC-2B x 12.7 (.5) Min Full Thread Motor with manifold mount is supplied with 2 O-rings. O-rings Zum Motor mit Universalanschluß werden 2 O-Ringe geliefert. Deux joints toriques sont livrés avec les moteurs a plan de raccordement universel (.812) Il blocchetto connessioni é corredato da 2 OR. 2.3 (.8) (.95) 6.2 (2.37) (2.35) For Manifold 12.7 (4.75) (4.675) For Manifold Code BM Weight/Gewicht kg Poids/Peso (lb) (15.4) (16.2) (16.9) (17.5) (18.4) (19.1) (2.6) (21.6) (23.7) Length "L" mm "L" (in) (4.41) (4.6) (4.78) (4.98) (5.17) (5.42) (5.8) (6.7) (6.64) English equivalents for metric specifications are shown in ( ). 28 Parker Hannifin Corporation
15 Mounting,Ports/Gehäuse,nschlüße Carter,Orifices / Montaje,Lumbreras 11 Series / Serie / Série HY /US,EU Code: BS SE B 2-Bolt, 7/8"-14 SE O-Ring Ø (4.5) 15.7 (.62) "L" B 29.2 (1.15) 14. (.55) 6.4 (.25) 2x 25.4 (1.) Ø (3.999) (.95) B 2X 14.2 (.56) (5.66) 176. (6.93) Max 7/16-2 STRIGHT THD O-RING CSE DRIN 2 X (1.255) 7/8-14 SE O-Ring (.95) Motor with manifold mount is supplied with 2 O-rings. Zum Motor mit Universalanschluß werden 2 O-Ringe geliefert. Deux joints toriques sont livrés avec les moteurs a plan de raccordement universel. Il blocchetto connessioni é corredato da 2 OR. O-rings 2.62 (.812) 2.3 (.8) 6.2 (2.37) (2.35) For Manifold 12.7 (4.75) (4.675) For Manifold Code BS Weight/Gewicht kg Poids/Peso (lb) (15.4) (16.2) (16.9) (17.5) (18.4) (19.1) (2.6) (21.6) ( 23.7) Length "L" mm "L" (in) (4.41) (4.6) (4.78) (4.98) (5.17) (5.42) (5.8) (6.7) (6.64) English equivalents for metric specifications are shown in ( ). 281 Parker Hannifin Corporation
16 Shafts / btriebswellen rbre / Ejes 11 Series / Serie / Série HY /US,EU Code Code B Code: 1" Keyed 45.5 (1.79) Code: 1 1" 6B Spline 45.5 (1.79) Code: 2 25mm Keyed 54.6 (2.15) Code: 3 1-1/4" Keyed 53.8 (2.12) English equivalents for metric specifications are shown in ( ). 282 Parker Hannifin Corporation
17 Shafts / btriebswellen rbre / Ejes 11 Series / Serie / Série HY /US,EU Code: 1 Keyed 18.6 (.73) Key 1/4 x 1 Woodruff #15 Per SE J (.251) ø (.999) 28.4 (1.12) 1/4-2 UNC thd x (.62) Min Deep Code: (1.) Min Full Spline SE 6B 1" 6B Spline 25.3 (.996) 1/4-2 UNC thd x (.62) Min Deep (.995) Code: 2 25mm Keyed Key 8x7x32mm (1.629) (1.472) 25. (.9843) M8x1.25H-6H x16.(.63) Min Deep 8. ( ) 2.9 (.826) Code: 3 1-1/4" Keyed 47.8 (1.88) 39.4 (1.55) x 7.95 (.313) ø (1.2495) 7.96 (.3135) 34.9 (1.373) 3/8-16 UNC thd x 19.5 (.75) Min Deep Key 7.95 x 31.5 (.313 x 1.24) Square English equivalents for metric specifications are shown in ( ). 283 Parker Hannifin Corporation
18 Shafts / btriebswellen rbre / Ejes 11 Series / Serie / Série HY /US,EU Code Code B Code: 5 1-1/4"-14 Tooth Spline 53.8 (2.12) Code: 6 7/8"-13 Tooth Spline 45.5 (1.79) English equivalents for metric specifications are shown in ( ). 284 Parker Hannifin Corporation
19 Shafts / btriebswellen rbre / Ejes 11 Series / Serie / Série HY /US,EU Code: (1.88) 33. (1.3) Min Full Spline 1-1/4"-14 Tooth Spline ø (1.2265) 3/8-16 UNC thd x 19.5 (.75) Min Deep ø (1.247) Code: 6 7/8"-13 Tooth Spline 25.4 (1.) Min Full Spline 13 Tooth 16/32 1/4-2 UNC thd x (.62) Min Deep ø (.995) ø (.8725) 1/4-2 UNC-2B x 15.7 (.62) Min Full Thd English equivalents for metric specifications are shown in ( ). 285 Parker Hannifin Corporation
20 11 Series / Serie / Série HY /US,EU 286 Parker Hannifin Corporation
LSHT Torqmotors TM and Nichols TM Motors zm09 110A Series
Technical Information /Technische Information / Segni / Informacion Tecnica 7 Displacements (3.6 16.4 in 3 /rev) 7 Schluckvolumen 59 269 cm 3 /rev 7 Cylindrée 7 Despazamientos Cont Int Maximum Pressure
More informationTechnical Information / Technische Information / Segni / Informacion Tecnica
Technical Information / Technische Information / Segni / Informacion Tecnica zm2 T Series / Serie / Série HY13-159-4/,EU 15 Displacements (2.2 24. in 3 /rev) 15 Schluckvolumen 36... 39 cm 3 /rev 15 Cylindrée
More informationLSHT Torqmotors and Nichols Motors 700 Series / Serie / Série. Technical Information /Technische Information / Segni / Informacion Tecnica
Technical Information /Technische Information / Segni / Informacion Tecnica Displacements Series (3. 1.9 in 3 /rev) Schluckvolumen 59 11 cm 3 /rev Cylindrée Parallel (7. 5.8 in 3 /rev) Despazamientos 118
More informationLSHT Torqmotors and Nichols Motors 716 Series / Serie / Série. Technical Information /Technische Information / Segni / Informacion Tecnica
Technical Information /Technische Information / Segni / Informacion Tecnica 6 Displacements Series (3.6 12.9 in 3 /rev) 6 Schluckvolumen 59 211 cm 3 /rev 6 Cylindrée Parallel (7.2 25.8 in 3 /rev) 6 Despazamientos
More informationLSHT Torqmotors and Nichols Motors. Catalog No. HY /US,EU
LSHT Torqmotors and Nichols Motors Catalog No. HY13-159-9/US,EU WRNING FILURE OR IMPROPER SELECTION OR IMPROPER USE OF THE PRODUCTS ND/OR SYSTEMS DESCRIED HEREIN OR RE- LTED ITEMS CN CUSE DETH, PERSONL
More informationHydraulics. Technical Information / Technische Information / Segni / Informacion Tecnica
Technical Information / Technische Information / Segni / Informacion Tecnica Low Speed High Torque, Hydraulic Motors T Series / Serie / Série HY13-1553-1/N,EU 15 Displacements (2.2 24. in 3 /rev) 15 Schluckvolumen
More informationTechnical Information /Technische Information / Segni/Informacion Tecnica. LSHT Torqmotors and Nichols Motors TG Series / Serie / Série
Technical Information /Technische Information / Segni/Informacion Tecnica 3 Displacements (8.6 to 58.5 in 3 /rev) 3 Schluckvolumen 4... 959 cm 3 /rev 3 Cylindrée 3 Despazamientos Maximum Pressure (3 psid)
More informationHydraulics. Technical Information /Technische Information / Segni/Informacion Tecnica. Low Speed High Torque Hydraulic Motors TF Series
Technical Information /Technische Information / Segni/Informacion Tecnica 11 Displacements (4.9-29.1 in 3 /rev) 11 Schluckvolumen 81... 477 cm 3 /rev 11 Cylindrée 11 Despazamientos Cont. Int. Maximum Pressure
More informationTechnical Information / Technische Information / Segni / Informacion Tecnica
Technical Information / Technische Information / Segni / Informacion Tecnica 15 Displacements (2.2 24. in 3 /rev) 15 Schluckvolumen 36... 39 cm 3 /rev 15 Cylindrée 15 Despazamientos Cont Int Maximum Pressure
More informationLSHT Torqmotors TM and Nichols TM Motors zm04 TJ Series
Technical Information / Technische Information / Segni / Informacion Tecnica zm4 HY13-159-4/,EU 14 Displacements (2.5 24. in 3 /rev) 14 Schluckvolumen 41... 39 cm 3 /rev 14 Cylindrée 14 Despazamientos
More informationTechnical Information /Technische Information / Segni/Informacion Tecnica. LSHT Torqmotors and Nichols Motors TK Series / Serie / Série
Technical Information /Technische Information / Segni/Informacion Tecnica 7 Displacements (15.3 to 61. in 3 /rev) 7 Schluckvolumen 25... 1 cm 3 /rev Cylindrée 7 Despazamientos Maximum Pressure ( psid)
More informationLSHT Torqmotors TM and Nichols TM Motors TF Series
Technical Information /Technische Information / Segni/Informacion Tecnica 11 Displacements (4.9-29.1 in 3 /rev) 11 Schluckvolumen 81... 477 cm 3 /rev 11 Cylindrée 11 Despazamientos Cont. Int. Maximum Pressure
More informationLSHT Torqmotors TM and Nichols TM Motors zm08 TK Series
Technical Information /Technische Information / Segni/Informacion Tecnica 7 Displacements (15.3 to 61. in 3 /rev) 7 Schluckvolumen 25... 1 cm 3 /rev Cylindrée 7 Despazamientos Cont. Int. Maximum Pressure
More informationLSHT Torqmotors TM and Nichols TM Motors zm07 TH Series
Technical Information /Technische Information / Segni/Informacion Tecnica 13 Displacements (8.6 to 58.5 in 3 /rev) 13 Schluckvolumen 141... 959 cm 3 /rev 13 Cylindrée 13 Despazamientos Cont. Int. Maximum
More informationHydraulics. Technical Information / Technische Information / Segni / Informacion Tecnica
Technical Information / Technische Information / Segni / Informacion Tecnica TE Series / Serie / Série HY13-1553-1/N,EU 14 Displacements (2.5 24. in 3 /rev) 14 Schluckvolumen 45... 39 cm 3 /rev 14 ylindrée
More informationTechnical Information /Technische Information / Segni / Informacion Tecnica 7 Displacements (3.6 16.4 in 3 /rev) 7 Schluckvolumen 59 269 cm 3 /rev 7 Cylindrée 7 Despazamientos Cont Int Maximum Pressure
More informationCAUTION! Exceptional Strength and Durability in a High Performance Motor/Brake Package
Technical Information /Technische Information / Segni/Informacion Tecnica 13 Displacements (8.6 to 58.5 in3/rev) 13 Schluckvolumen 141... 959 cm 3 /rev 13 Cylindrée 13 Despazamientos Cont. Int. Maximum
More informationHydraulics. Low Speed High Torque Brake Motors BH Series. Technical Information /Technische Information / Segni/Informacion Tecnica C204
Technical Information /Technische Information / Segni/Informacion Tecnica 12 Displacements (8.6 to 58.5 in 3 /rev) 12 Schluckvolumen 140... 958 cm 3 /rev 12 ylindrée 12 Despazamientos ont. Int. Maximum
More informationHydraulics. Low Speed High Torque Brake Motors BG Series. Technical Information /Technische Information / Segni/Informacion Tecnica C170
Technical Information /Technische Information / Segni/Informacion Tecnica 12 Displacements (8.6 to 58.5 in 3 /rev) 12 Schluckvolumen 140... 960 cm 3 /rev 12 ylindrée 12 Despazamientos ont. Int. Maximum
More informationÀ cylindrée fixe Gamme MAP 50
pplications Moteur à pistons axiaux M+S À cylindrée fixe Gamme MP Cylindrée de 6,6 à cm Vitesse de rotation maxi de tmin Couple maxi danm Puissance maxi 6 Kw ébit d huile maxi : 9 lmin Charge axiale maxi
More informationMotors & Pumps- Hydraulic Pumps, Motors & Power Units
- Hydraulic umps, Motors & ower Units - Rapid Response...12-1 12-6 Hydraulic umps - Check Valves...12-7 Hydraulic umps - ower Units...12-8 12-9 12MOTORS & UMS Hydraulic umps - Vane ump...12-10 Motors...12-11
More informationC9: BMM, BMP, BMR, BMH, BMJ Series & Valves CONTENT. Usage Guide 2. BMM Series Hydraulic Motors 3. BMP Series Hydraulic Motors 11
C9: BMM, BMP, BMR, BMH, BMJ Series & Valves CONTENT Usage Guide 2 BMM Series Hydraulic Motors 3 BMP Series Hydraulic Motors 11 BMR Series Hydraulic Motors 24 BMH Series Hydraulic Motors 35 BMJ Series Hydraulic
More informationGear Pumps / Motors. Series PGP / PGM Fixed Displacement Pumps, Cast-Iron and Aluminium Designs
Gear Pumps / Motors Series PGP / PGM Fixed Displacement Pumps, Cast-Iron and Aluminium Designs Table of contents Heavy-duty Pumps and Motors Series PGP, PGM Contents Page Series 500 Aluminium Table of
More informationHPVR-10 AXIAL PISTON PUMPS
The HPVR series of inline axial piston variable displacement pumps, are available in five displacements and three compact frame sizes. These pumps feature medium-high working pressure capabilities that
More informationSeries PHP10 Variable Volume, Piston Pumps
Catalog HY13-1553-1/N,EU Series PHP1 Series PHP1 Variable Volume, Piston Pumps Bulletin 2-18/US 123 Catalog HY13-1553-1/N,EU Series PHP1 Performance Information Series PHP1 Pressure Compensated, Variable
More informationOMP Hydraulic Motor Versions
Versions VERSIONS Mounting flange Shaft Port size European version US version Side port version End port version Flange port version G 1 /2 X X X No No OMP Cyl. 25 mm G 1 /2 X X X Yes No OMP G 1 /2 X X
More informationMobile Hydraulic Pumps T6G, T67G, T6ZC. Denison Vane Technology, fixed displacement
Mobile Hydraulic Pumps T6G, T67G, T6ZC Denison Vane Technology, fixed displacement aerospace climate control electromechanical filtration fluid & gas handling hydraulics pneumatics process control sealing
More informationSPECIAL HYDRAULIC MOTORS AND MOTOR-BRAKES
SPECIAL HYDRAULIC AND MTRBRAKES CNTENTS Page Hydraulic Motors Series HP... Hydraulic Motors Series HR...11 Hydraulic Motors Series MLHRW...1 Hydraulic Motors Series...2 Hydraulic Motorbrakes Series BHR...3
More informationIndustrial Hydraulic Pumps T7DBB, T7DBBS. We are doing our parts to keep you moving! Denison Vane Technology, fixed displacement
Industrial T7DBB, T7DBBS Denison Vane Technology, fixed displacement Hydraulic Motors Hydraulic Valves Hydraulic Cylinders Hydraulic Filtration Hydraulic Accumalators We are doing our parts to keep you
More informationFixed Displacement Motor AA2FM (A2FM)
Fixed Displacement Motor 2FM (2FM) Series 6, for Open and Closed Circuits xial Piston, ent xis Design 5800 psi 6500 psi rueninghaus Hydromatik Sizes 5 1000 Nominal Pressure up to Peak Pressure up to (400
More informationDouble Pump Operating Specifications
Double Pump Operating Specifications Shaft End Pump Cover End Pump Typical Typical Typical Typical del. input del. input Delivery L/min kw Delivery L/min kw USgpm @ (USgpm) (hp) USgpm @ (USgpm) (hp) 12
More informationPerformance Information Series PVP 100/140 Pressure Compensated, Variable Volume, Piston Pumps
Catalog HY13-155-2/US Technical Information Series PVP 1/14 Performance Information Series PVP 1/14 Compensated, Variable Volume, Piston Pumps Features High Strength Cast-Iron Housing for Reliability and
More informationHYDRAULIC MOTORS GENERAL INFORMATION
GENERAL INFORMATION MGL... Document: HM-1-Dec 2012 Applications: -Agricultural harvesters and seeders -Conveyors -Machine tools -Food industries -Turn equipment -Brush drivers -Sweepers and floor polishers
More informationTorqmotor Series TF/TG/TH/TK
Sepehr Hydraulic Asia Series TF/TG/TH/TK max. 49 kw Catalogue HY11-3213/EU Ed. 06 / 2003 Series DE Hinweis Die in diesem Katalog oder in Form anderer Informationen durch die Parker Hannifin GmbH, ihre
More informationGEAR PUMPS DIMENSIONAL DETAILS
DIMENSIONAL DETAILS OUTLET INLET TYPE DISPLACEMENT CM 3 /REV FLOW AT 1500 REV/MIN MAX. WORKING PRESSURE MAX. SPEED DIMENSIONS MM P1 P2 P3 RPM L M D2 1.4 2.0 270 290 310 6000 40 79 D3 2.1 2.9 270 290 310
More informationYMSY. Advanced design in disc distribution flow,which can automatically compensate in operating with high volume efficiency and long life.
The series motors adapts an advanced ROLLER gear set designed with disc distribution flow and high pressure. This motor series uses the ROTOR gear type manufactured with most advanced technology and quality
More informationUS version. Drain connection
Versions OMT Versions Mounting flange Standard flange Shaft Port size Europea n version US version Drain connection Check valve Low pressure release High pressure release Cyl. 4 mm G 3/4 X Yes Yes OMT
More informationSize CC-A Flange Options-B Shaft Options-C Ports Features. SAE A 2 Bolt - (H2) 4 Bolt Magneto (H6) 4 Bolt Square (H4)
Gerolor Motors S Series Size CC-A Flange Options-B Shaft Options-C Ports Features S S S S S S S S2 2 S31 31 S0 0 SAE A 2 Bolt - (H2) 4 Bolt Magneto (H6) 4 Bolt Square (H4) 1.0" Keyed (R) mm Keyed (A) 1.0'
More informationMobile Hydraulic Pumps T6DCCM. We are doing our parts to keep you moving! Denison Vane Technology, fixed displacement
Mobile Hydraulic Pumps T6DCCM Denison Vane Technology, fixed displacement Hydraulic Pumps Hydraulic Motors Hydraulic Valves Hydraulic Cylinders Hydraulic Filtration Hydraulic Accumalators We are doing
More informationSeries 20 Axial Piston Motors. Technical Information
Series 20 xial Piston Motors Technical Information General Description INTRODUCTION Sauer-Danfoss a world leader in hydraulic power systems has developed a family of axial piston motors. DESCRIPTION Sauer-Danfoss
More informationDisc Valve Hydraulic Motors 2000 Series
Disc Valve Hydraulic Motors 10.2014 inspired hydraulics. Änderungen und Druckfehler vorbehalten 10.2014 EN EATON_Motoren english Highlights Port A Features Three zone design for longer life and true bi-directionality.
More informationHydraulic Pumps T7 for variable speed drives
FC Hydraulic Pumps T7 for variable speed drives Denison Vane Technology Catalogue HY29-11/UK Content General Information Introduction and product key features 3 Main Technical Data Main table for single
More informationHydraulic Motor & Brake
SERIES 500-501 - 510-511 - 520-521 - 530-531 - 50-51 - MEDIUM DUTY Hydraulic Motor & rake RE RE (ll Series) For Medium Duty pplications Overview series descriptions RE Series motors offer the perfect compromise
More informationVickers. Vane Pumps. Double Thru-drive Vane Pumps. High speed, high pressure VQT Series for mobile equipment. Released 7/93
Vickers Vane Pumps Double Thru-drive Vane Pumps High speed, high pressure VQT Series for mobile equipment Released 7/93 612 Introduction Double VQT high performance pumps are fixed displacement units that
More informationMOVICONTROL. Single and Double Fixed Vane Pumps SERIES V10, V20, 25V/VQ, 35V/VQ, 45V/VQ.
Single and Double Fixed Vane Pumps SERIES V10, V20, 25V/VQ, 35V/VQ, 45V/VQ www.movicontrol.com.br V10/V20 Series Features Balanced vane type pumps are excellent for medium- to low-pressure mobile and industrial
More informationFIXED DISPLACEMENT VANE PUMPS
FIXED DISPLACEMENT VANE PUMPS Single Vane Pumps Double Vane Pumps Thru-Drive Vane Pumps HS - HQ - VH - SERIES Working pressure: up to 210 bar Displacements: from 3 cc to 200 cc Pumps, cartridges and spare
More informationMobile Hydraulic Pumps T6DCM, T6DCP, T6DCMW. We are doing our parts to keep you moving! Denison Vane Technology, fixed displacement
Mobile Hydraulic Pumps T6DCM, T6DCP, T6DCMW Denison Vane Technology, fixed displacement Hydraulic Pumps Hydraulic Motors Hydraulic Valves Hydraulic Cylinders Hydraulic Filtration Hydraulic Accumalators
More informationSeries 20 Axial Piston Motors. Technical Information
Series 20 xial Piston Motors Technical Information General Description INTRODUCTION Sauer-Danfoss a world leader in hydraulic power systems has developed a family of axial piston motors. DESCRIPTION Sauer-Danfoss
More informationPiston Pumps Series P2 / P3 Variable Displacement
Piston Pumps Series P2 / P3 Variable Displacement Catalogue HY11-2600/UK July 2003 Contents Series P2/P3 Description Technical information 3 Ordering code 4 Control options LA and LB 6 Control options
More informationP2060 P2075 P2105 P2145 P3105 P3145
Technical Information Technical Features P2 Series Compact design Low noise level Service friendly Reliable Long-lasting Flexible Easy to install High self-priming speed Technical Data P3 Series P2 Series
More informationMOTOR SCM ISO
MOTOR SCM 012-130 ISO SCM 012-130 ISO is a range of robust axial piston motors especially suitable for mobile hydraulics. SCM 012-130 ISO is of the bent-axis type with spherical pistons. The design results
More informationMOTOR SCM M2
MOTOR SCM 025 108 M2 Sunfab SCM M2 is a range of robust axial piston motors especially suitable for winch-, slewing-, wheeland track drives. Sunfab SCM M2 is of the bent-axis type with spherical pistons.
More informationCROSS HYDRAULICS PTY LTD SECTION
OVERVIEW The motor series is an economical alternative to more complex geroler designs that still provides high efficiency across a wide performance range. These motors are intended for medium-duty applications
More informationWide range of hydraulic motors & valves BM2 BM1 H PORT BM1 LINE PORT BM1 S PORT HMM BM4 BM3 WHEEL MOTOR MOTOR WITH SPEED SENSOR
Wide range of hydraulic motors & valves BM2 BM1 H PORT BM1 LINE PORT BM1 S PORT HMM BM4 BM3 WHEEL MOTOR MOTOR WITH SPEED SENSOR 4K BM5 BEARINGLESS BM5 BMT BM6 BEARINGLESS BM6 MOTOR BALANCE VALVE MOTOR
More informationAXIAL PISTON PUMPS SHPV SECTIONAL VIEW
AXIAL PISTON PUMPS SHPV SECTIONAL VIEW 2 SYSTEM CIRCUIT PUMP AND MOTOR CIRCUIT working loop (high pressure) working loop (low pressure) control fluid suction line case drain fluid Above figure shows schematically
More informationSCM ISO. SCM ISO is a range of robust axial piston motors especially suitable for mobile hydraulics.
SCM 010-130 ISO is a range of robust axial piston motors especially suitable for mobile hydraulics. SCM 010-130 ISO is of the bent-axis type with spherical pistons. The design results in a compact motor
More informationTruck Hydraulics. Series F1, F2, T1 Fixed Displacement Pumps
Series F1, F2, T1 Fixed Displacement Pumps aerospace climate control electromechanical filtration fluid & gas handling hydraulics pneumatics process control sealing & shielding Contents Hydraulic Pumps,
More informationFEATURES SPECIFICATIONS
FETURES 1 Heavy-Duty Drive Link is up to 30% stronger than competitive designs for longer life. 1 2 3 H 2 Three-Zone Orbiting Valve precisely meters oil to produce exceptional volumetric efficiency. 3
More informationTorqmotor TM. Series TF / TG / TH / TK max 49 kw Low-speed hydraulic motor
Torqmotor TM Series TF / TG / TH / TK max 49 kw Low-speed hydraulic motor aerospace climate control electromechanical filtration fluid & gas handling hydraulics pneumatics process control sealing & shielding
More informationHYDRAULIC MOTORS MLHH
HYDRAULIC APPLICATION» Conveyors» Feeding mechanism of robots and manipulators» Metal working machines» Textile machines» Machines for agriculture» Food industries» Mining machinery etc. CONTENTS Specification
More informationAXIAL PISTON MOTORS SHMF
SECTIONAL VIEW Purge relief valve High pressure relief valves (adjustable) Cylinder block assembly Shaft seal Output shaft Valve block Shuttle valve Swashplate 2 SYSTEM CIRCUIT PUMP AND MOTOR CIRCUIT working
More informationwhitedriveproducts SERIES Hydraulic Motor LIGHT DUTY
SERIES 0-1 - LIHT DUTY Hydraulic Motor RS RS (ll Series) For Light Duty pplications Overview RS Series motors are the most economical model in the White Drive Products product line, but are not low-tech.
More informationSeries PVP Variable Volume, Piston Pumps
Catalog HY13-1553-1/N,EU Series PVP Variable Volume, Piston Pumps Catalog 26-12-1/US hpm12-1.p65, lw, jk 57 Catalog HY13-1553-1/N,EU hpm12-1.p65, lw, jk 58 Catalog HY13-1553-1/N,EU Introduction Series
More informationENGINEERING DATA. High Torque, Low Speed Motors H, S, 2000, 6000, and 10,000 Series. w w w. F l u i D y n e F P. c o m
ENGINEERING DATA High Torque, Low Speed Motors H, S, 2000, 6000, and 10,000 Series Interchangeable with: Charlynn White Ross Parker Danfoss w w w. INDEX Cross Reference Guide...2 Introduction...3 H-Series...4
More informationD SERIES HYDRAULIC PUMP
uk distributor for D SERIES HYDRAULIC PUMP quality products for mechanical & fluid power jbj Techniques Limited, www.jbj.co.uk Introduction to Concentric D Series Hydraulic Pumps Concentric offers one
More informationQuality. 1. Cam ring 2. Cam roller 3. Piston 4. Shaft coupling Connection block 10. Valve plate 11. Axial bearing 6
Functional description Hägglunds hydraulic industrial motor COMPACT CB is of the radial-piston type with a rotating cylinder block/hollow shaft and a stationary housing. The cylinder block is mounted in
More informationSCM SAE. Other advantages: Sunfab s SCM SAE is a range of robust axial piston motors especially suitable for mobile hydraulics.
Sunfab s SCM 010-130 SAE is a range of robust axial piston motors especially suitable for mobile hydraulics. SCM 010-130 SAE is of the bent-axis type with spherical pistons. The design results in a compact
More informationAxial Piston Pump Series PV Design 45 Variable Displacement. Catalogue HY /UK February 2007
Design 45 Variable Displacement February 2007 Introduction With thru drive for single and multiple pumps Swash plate type for open circuit Technical Features Low noise level Fast response (eg. PV046: upstroke
More informationSCM M2. Other advantages:
Sunfab s SCM 025-108 M2 is a range of robust axial piston motors with cartridge flange especially suitable for winch-, slewing-, wheel- and track drives. SCM 025-108 M2 is of the bent-axis type with spherical
More informationEA5506. Electrically Actuated Carbon Steel PN16 Ball Valve. Description
Electrically Actuated Carbon Steel PN16 Ball Valve Direct Mount No Brackets Needed Carbon Steel Body WCB Full Bore DN15-DN100 / 1/2-4" Powerful Electric Actuator Many Optional Extras Offered Seats Description
More informationDisplacements cm 3 /r [in 3 /r] Design code [21.0] 400 [24.4] 434 [26.5] 480 [29.3] 677 [41.3] HP30 Motor
HP30 Motor Design code -003 Displacements cm 3 /r [in 3 /r] 344 [21.0] 400 [24.4] 434 [26.5] 480 [29.3] 677 [41.3] Engineered for performance For the past 55 years, Char-Lynn has been recognized as the
More informationPerformance Information Series PVP 41/48 Pressure Compensated, Variable Volume, Piston Pumps
Catalog HY13-1553-1/N,EU Technical Information Performance Information Compensated, Variable Volume, Piston Pumps Features High Strength Cast-Iron Housing for Reliability and Quiet Operation Vickers Porting
More information10,000 Series. Highlights C-6
Highlights Features higher flows Benefits demanding mobile and industrial applications from Applications Description This is the biggest disc valve motor of our line with up to 45 GPM and 24,000 in-lb
More informationHigh Torque Low Speed Motors MR - MRE
High Torque Low Speed Motors MR - MRE Calzoni Radial Piston Technology aerospace climate control electromechanical filtration fluid & gas handling hydraulics pneumatics process control sealing & shielding
More informationYMTE SPECIFICATION DATA
SPECIFICATION DATA For individual motor performance charts consult equivalent YMT series data DISTRIBUTION TYPE GEOMETRIC DISPLACEMENT MAX. SPEED RPM MAX. TORQUE [IN. LB.] N*M MAX. OUTPUT [HP] KW MAX.
More informationVeljan Gear Pumps. E' Series Features:-
E' Series Features:- Heavy duty sleeve bushing design in a small frame size Displacements from 43.5cc/rev to 146.5cc/rev Working pressures up to 240bar Speeds up to 3500rpm Flows up to 38.7gpm High strength
More informationCONTENT Axial Piston Motors and Pumps Fixed Displacement. Technical Specification Guide...2. Hydraulic motor MAP Hydraulic motor MAP50...
CONTENT CONTENT Aial Piston Motors and Pumps Fied Displacement PAGE Technical Specification Guide...2 Hydraulic motor...6 Hydraulic motor MAP5...1 Hydraulic motor MAP1...2 MAP5 Hydraulic pump PAP5...29
More informationGear Housing Widths 1.00" 1.25" 1.50" 1.75" 2.00" 2.25" 2.50" Gear Housing Widths / Flow Rate [ VGP - D Series ]
'D' Series Features:- Heavy duty sleeve bushing design in a small frame size Displacements from 20.6cc/rev to 104.2cc/rev Working pressures up to 240bar Speeds up to 3500rpm Flows up to 27.5gpm High strength
More informationDisc Valve Hydraulic Motors 4000 Compact Series
Disc Valve Hydraulic Motors 10.2014 inspired hydraulics. Änderungen und Druckfehler vorbehalten 10.2014 EN EATON_Motoren english Port B Port A Features Shuttle Valve with Back- Pressure Relief Valve Highlights
More informationDisc Valve Hydraulic Motors
Disc Valve Hydraulic Motors State of the art motors benefiting from years of experience and inovating constantly to fit your demands. C-i Disc Valve Hydraulic Motors Highlights Product Description In the
More informationDisc Valve Hydraulic Motors Series 6000
Disc Valve Hydraulic Motors Series 6000 10.2014 inspired hydraulics. Änderungen und Druckfehler vorbehalten 10.2014 EN EATON_Motoren english Highlights Features 9 displacements available Presents a multitude
More informationwhite drive products SERIES HYDRAULIC MOTORS
white drive products WR SERIES HYDRULIC MOTORS WR overview The WR Series motor incorporates the latest advances for smooth performance, efficiency and durability. It features an optimized Roller Stator
More informationGM25 Motor Dimensional Information
GM25 Series Birotational Hydraulic Motors GM25 Series hydraulic motors are designed for low noise, high efficiency birotational operation. Cast iron construction insures reliability and strength. A number
More informationCONTINENTAL HYDRAULICS PVER VANE PUMPS
CONTINENTAL HYDRAULICS PVER VANE PUMPS 5505 WEST 123RD STREET SAVAGE, MN 55378-1299 / PH: 952.895.6400 / WWW.CONTINENTALHYDRAULICS.COM PVER PUMPS FEATURES AND BENEFITS The PVER series vane pumps are variable
More informationOrbital Motors OMS, OMT and OMV Orbital Motors
MKING MODERN LIVING POSSIBLE Technical Information Orbital Motors OMS, OMT and OMV Orbital Motors powersolutions.danfoss.com Revision history Table of revisions Date Changed Rev November 214 Converted
More informationSize CC-A Flange Options-B Shaft Options-C Ports Features. SAE A 2 Bolt - (E2) 4 Bolt Square (E4)
Gerolor Motors BMRS Series Size CC-A Flange Options-B Shaft Options-C Ports Features 100 100 1 1 1 1 200 200 2 3 2 3 3 3 SAE A 2 Bolt - (E2) 4 Bolt Square (E4) 1-1/4" Keyed (G) 32mm Keyed (B) 1-1/4' 14T
More informationMJ SERIES LOW SPEED HIGH TORQUE MOTORS
MJ SERIES LOW SPEED HIGH TORQUE MOTORS HIGH EFFICIENCY TORQUE MOTORS The MJ Series Low Speed High Torque Motor is available in 10 displacement sizes. The MJ Series motor is constructed using heavy-duty
More informationDisc Valve Hydraulic Motors Series 4000
Disc Valve Hydraulic Motors Series 0 10.20 inspired hydraulics. Änderungen und Druckfehler vorbehalten 10.20 EN EATON_Motoren english Highlights Features 10 displacements, a variety of mounting flanges
More informationBENT AXIS PISTON MOTORS SERIES HPM FLANGE ISO HPM. pag.3
ENT AXIS PISTON MOTORS SERIES HPM FLANGE ISO 3019-2 HPM pag.3 TECHNICAL FEATURES ENT AXIS PISTON MOTORS SERIES HPM FLANGE ISO 3019-2 TECHNICAL FEATURES Displacement cm 3 /rev 12 17 25 34 40 47 55 64 80
More informationPVE /117 ED VARIABLE DISPLACEMENT VANE PUMPS WITH DIRECT PRESSURE ADJUSTMENT SERIES 30 OPERATING PRINCIPLE TECHNICAL SPECIFICATIONS
14 110/117 ED PVE VARIABLE DISPLACEMENT VANE PUMPS WITH DIRECT PRESSURE ADJUSTMENT OPERATING PRINCIPLE The PVE pumps are variable displacement vane pumps with direct pressure regulator. The pump group
More informationPowrFlow PVX Vane Pumps
PowrFlow PVX Vane Pumps POWRFLOW PVX VANE PUMPS YOUR SOURCE FOR VANE PUMPS FOR THE MOST DEMANDING APPLICATIONS What Makes PowrFlow PVX Vane Pumps Your Best Buy? Continental Hydraulics PowrFlow PVX Vane
More informationCatalog PowrFlowTM PVX Vane Pumps
Catalog PowrFlowTM PVX Vane Pumps Your source for vane pumps for the most demanding applications. What Makes PowrFlow PVX Vane Pumps Your Best Buy? Continental Hydraulics PowrFlow PVX Vane Pumps deliver
More informationMobile Hydraulic Pumps T6EM, T6EP. We are doing our parts to keep you moving! Denison Vane Technology, fixed displacement
Mobile Hydraulic Pumps T6EM, T6EP Denison Vane Technology, fixed displacement Hydraulic Pumps Hydraulic Motors Hydraulic Valves Hydraulic Cylinders Hydraulic Filtration Hydraulic Accumalators We are doing
More informationPVX-11 VANE PUMPS. See pages 12 thru 14 for PVX-11 dimensions. VARIABLE DISPLACEMENT, PRESSURE COMPENSATED PERFORMANCE SPECIFICATIONS
PVX-11 VANE PUMPS VARIABLE DISPLACEMENT, COMPENSATED NOTE: See pages thru 14 for PVX-11 dimensions. PERFORMANCE SPECIFICATIONS Displacement (Nominal) 1.5 in 3 /rev. (25 cm 3 /rev.) Displacement (Actual)
More informationTMVW Orbital Motors. Technical Information
Orbital Motors Technical Information A Wide Range of Orbital Motors A Wide Range of Orbital Motors F300030 Tif Sauer-Danfoss is a world leader within production of low speed orbital motors with high torque.
More informationwhitedriveproducts SERIES Hydraulic Motor LIGHT DUTY
whitedriveproducts SERIES 145-146 - LIGHT DUTY Hydraulic Motor www.cenhyd.com 1(800)264-9571 WD WD (All Series) whitedriveproducts overview The WD motor series is an economical solution for light duty
More informationSKU: DR4306. Fixed Orifice Double Regulating Valve
SKU: DR4306 VOLT Fixed Orifice Double Regulating Valve 1/2" - 2" Brass Double Regulating Valve with Test Points 1/2" - 2" Messing Doppelregelventilmit Testpunkte 1/2" - 2" Latón Doble Válvula reguladora
More informationSpool Valve Hydraulic Motors Series J
Spool Valve Hydraulic Motors Series J 10.201 inspired hydraulics. Änderungen und Druckfehler vorbehalten 10.201 EN EATON_Motoren J Series english J Series Highlights Thrust Bearing Bushing Port B Port
More informationW1200 SERIES HYDRAULIC PUMP
W1200 SERIES HYDRAULIC PUMP HYDRAULIC SYSTEMS DIVISION Outstanding Hydraulic Products, Service and Expertise, Worldwide 2 Table of Contents Description Page Number W1200 Product Specifications and Performance
More informationHYDRAULIC MOTORS MM APPLICATION OPTIONS CONTENTS GENERAL MOTORS
HYDRAULIC APPLICATION Conveyors Textile machines Mining machinery Machine tools Ventilators Construction plant equipment and access platforms etc. CONTENTS Specification data... 5 Function diagrams...
More information