LSHT Torqmotors TM and Nichols TM Motors zm09 110A Series

Size: px

Start display at page:

Download "LSHT Torqmotors TM and Nichols TM Motors zm09 110A Series"

Elvin Peters
6 years ago
Views:

Technical Information /Technische Information / Segni / Informacion Tecnica 7 Displacements (3.6 16.

1 Technical Information /Technische Information / Segni / Informacion Tecnica 7 Displacements ( in 3 /rev) 7 Schluckvolumen cm 3 /rev 7 Cylindrée 7 Despazamientos Cont Int Maximum Pressure (to 25 ) (to 3 ) Eingangsdruck Pression entrée Presion Maxima zm9 11 Series HY /US,EU When the Ultimate in Efficiency and Reliability is a Must This high performance motor contains a power element that is pressure loaded against internal leakage for high volumetric efficiency. It is wear compensated, so that its volumetric efficiency will not degrade with use. It can provide up to 5215 lb-in of torque through a one-piece solid fixed axis shaft. This shaft design allows for full stationary spline contact between shaft and rotor, minimizing spline contact stresses. It also allows the shaft to be extended through the rear cover for mounting parking brakes, auxiliary drive functions or encoders for speed readout or closed loop control. Low internal pressure drop means high mechanical efficiency and higher flow capability. This rugged motor is the most compact on the market. Maximum Oil Flow Schluckstrom Débit d huile Caudal Maximo de ceite Maximum Speed Drehzahl Vitesse de rotation Velocidad Maxima (to 3 gpm) lpm 858 rpm Cont Int Maximum Torque (to 4164 lb in) (to 5215 lb in) Max Drehmoment 47 Nm 589 Nm Couple Torque Maximo Maximum Side Load at Key Seitenlast Charges latèrales Carga Maxima Lateral (to 145 lb) 645 N pp Series SD.p Parker Hannifin Corporation

2 Performance Data / Leistungsdaten Puissance / Datos Tecnicos 11 Series HY /US,EU Motor Series 11 Geometric displacement cm 3 /rev in 3 /rev rev/min Geom. Schluckvolumen Cylindrée Cilindrata Max. Max. intermittent flow Max. Drehzahl Intermittierender etrieb: Vitesse de rotation maxi Velocidad maxima a caudal intermitente maximo Max. oil flow Max. Schluckstrom Débit d huile maxi Portata max cont / int* l/min g/min cont / int* Max. differential pressure Max. Druckgefälle Chute de pression maxi Presion diferencial maxima max Max. supply pressure Max. Eingangsdruck Pression maxi entrée Presion maxima de alimentacion cont / int* Nm lb-in Max. torque Max. Drehmoment Couple maxi Torque Maximo max KW HP Max. performance Max. Leistungabgabe Puissance de sortie maxi Maximo rendimento Performance data based on tests using 15W4 oil with a viscosity of 55 cst (215 SUS) at 54 C (13 F.) Performance data is typical. ctual data may vary slightly from one production motor to another. Les donnees sur les performances sont basees sur des tests utilisant de l huile 15W4 d une viscosite de 55 cst (215 SUS) a 54 C (13 F). Ces donnees correspondent a des situations typiques. Les donnees reelles peuvent varier legerement d un moteur de production a l autre. Leistugsdaten sind gemessen mit SE 15W4 bei einer Viskositaet von 43,1 Cst beo 54 C. Geringfuegige bweichungen von den Katalogerten sond moeglich. Datos tecnicos obtenidos con aceite 15W4 de 55 cst (215 SUS) de viscosidad a 54 C (13 F). Los datos proporcionados son valores tipcos. Los valores exactos reales podrian tener una pequena variacion entre distintos motores. * Intermittent operation rating applies to 1% of every minute. Intermittierende Werte maximal 1% von jeder etriebsminute. Fonctionnement interm. 1% max. de chaque minute d`utilisation. Capacidad de funcionamiento intermitente valida para 1% por cada minuto. pp Series SD.p Parker Hannifin Corporation

3 Ordering Information / estellschlüssel System de Commande / Imformacion para pedidos 11 Series HY /US,EU 11 Series X Shaft Welle rbre Ejes Engineering Design technischer Entwurf Conception technique Diseño de ingeniería XXX Displacement Schluckvolumen Cylindrée Desplazamiento X Mounting Gehäuse Carter Montaje X Ports nschluß Plan de raccordement Lumbreras X Thru-Shaft durchgehende Welle arbre traversant Eje pasante X X Shaft Material Cross-Over Wellenmaterial Relief Valve Matériel d'arbre remslüftventil Material del eje Soupape de sûreté transversale Paint Válvula de alivio transversal X Code 1" Keyed Code SE 2-olt, Manifold 1 2 1" 6 Spline 25mm Keyed 1-1/4" Keyed cm³/u cm³/tr Code cm³/giro cu in³/rev / / / / / / / 16.4 M S T SE 2-olt, 7/8-14 SE SE 2-olt, 1/2 -SPP 3 SE 2-olt, Manifold 1-1/4"-14 Tooth Spline M 5 SE 2-olt, 7/8-14 SE 7/8"-13 Tooth Spline S 6 Code No Thru Shaft 1 Thru Shaft E Endcoder Code Omit S If Not Required Stainless Steel Code Omit R1 If Not Required Cross-Over Relief Valve Code Omit F Consult factory for other available options, configurations ordering codes and lead times. pp Series SD.p65 No Paint lack Paint Schwarz lackiert 174 Parker Hannifin Corporation

4 Performance Data / Leistungsdaten Puissance / Datos Tecnicos 11 Series HY /US,EU Schluckstrom [L/min] Flow [G/min] US Drehmoment [Nm] Drehmoment [Nm] Drehzahl [1/min] Schluckstrom [L/min] Drehzahl [1/min] Torque [lb/in] Torque [lb/in] Speed [Rpm] Flow [G/min] US Speed [Rpm] Drehmoment [Nm] Schluckstrom [L/min] Drehzahl [1/min] Torque [lb/in] Flow [G/min] US Speed [Rpm] Cont. Cont. with no side load Int. with rated side load Int. Intermittent operation rating applies to 1% of every minute. Fonctionnement interm. 1% max. de chaque minute d`utilisation. Performance data based on tests using 15W4 oil with a viscosity of 55 cst (215 SUS) at 54 C (13 F.) Performance data is typical. ctual data may vary slightly from one production motor to another. Les donnees sur les performances sont basees sur des tests utilisant de l huile 15W4 d une viscosite de 55 cst (215 SUS) a 54 C (13 F). Ces donnees correspondent a des situations typiques. Les donnees reelles peuvent varier legerement d un moteur de production a l autre. pp Series SD.p65 Intermittierende Werte maximal 1% von jeder etriebsminute. Capacidad de funcionamiento intermitente valida para 1% por cada minuto. Leistugsdaten sind gemessen mit SE 15W4 bei einer Viskositaet von 43,1 Cst beo 54 C. Geringfuegige bweichungen von den Katalogerten sond moeglich. Datos tecnicos obtenidos con aceite 15W4 de 55 cst (215 SUS) de viscosidad a 54 C (13 F). Los datos proporcionados son valores tipcos. Los valores exactos reales podrian tener una pequena variacion entre distintos motores. 175 Parker Hannifin Corporation

5 Performance Data / Leistungsdaten Puissance / Datos Tecnicos 11 Series HY /US,EU Schluckstrom [L/min] Flow [G/min] US Drehmoment [Nm] Torque [lb/in] Drehmoment [Nm] Drehzahl [1/min] Schluckstrom [L/min] Drehzahl [1/min] Torque [lb/in] Speed [Rpm] Flow [G/min] US Speed [Rpm] Drehmoment [Nm] Schluckstrom [L/min] Drehzahl [1/min] Torque [lb/in] Flow [G/min] US Speed [Rpm] Cont. pp Series SD.p65 Cont. with no side load Int. with rated side load Int. Intermittent operation rating applies to 1% of every minute. Intermittierende Werte maximal 1% von jeder etriebsminute. Fonctionnement interm. 1% max. de chaque minute d`utilisation. Capacidad de funcionamiento intermitente valida para 1% por cada minuto. Performance data based on tests using 15W4 oil with a viscosity of Leistugsdaten sind gemessen mit SE 15W4 bei einer Viskositaet von 43,1 Cst 55 cst (215 SUS) at 54 C (13 F.) Performance data is typical. ctual data beo 54 C. Geringfuegige bweichungen von den Katalogerten sond moeglich. may vary slightly from one production motor to another. Datos tecnicos obtenidos con aceite 15W4 de 55 cst (215 SUS) de viscosidad Les donnees sur les performances sont basees sur des tests utilisant de l huile a 54 C (13 F). Los datos proporcionados son valores tipcos. Los valores 15W4 d une viscosite de 55 cst (215 SUS) a 54 C (13 F). Ces donnees exactos reales podrian tener una pequena variacion entre distintos motores. correspondent a des situations typiques. Les donnees reelles peuvent varier legerement d un moteur de production a l autre. 176 Parker Hannifin Corporation

6 Performance Data / Leistungsdaten Puissance / Datos Tecnicos 11 Series HY /US,EU Drehmoment [Nm] Schluckstrom [L/min] Drehzahl [1/min] Torque [lb/in] Flow [G/min] US Speed [Rpm] Cont. Cont. with no side load Int. with rated side load Int. Intermittent operation rating applies to 1% of every minute. Fonctionnement interm. 1% max. de chaque minute d`utilisation. Performance data based on tests using 15W4 oil with a viscosity of 55 cst (215 SUS) at 54 C (13 F.) Performance data is typical. ctual data may vary slightly from one production motor to another. Les donnees sur les performances sont basees sur des tests utilisant de l huile 15W4 d une viscosite de 55 cst (215 SUS) a 54 C (13 F). Ces donnees correspondent a des situations typiques. Les donnees reelles peuvent varier legerement d un moteur de production a l autre. pp Series SD.p65 Intermittierende Werte maximal 1% von jeder etriebsminute. Capacidad de funcionamiento intermitente valida para 1% por cada minuto. Leistugsdaten sind gemessen mit SE 15W4 bei einer Viskositaet von 43,1 Cst beo 54 C. Geringfuegige bweichungen von den Katalogerten sond moeglich. Datos tecnicos obtenidos con aceite 15W4 de 55 cst (215 SUS) de viscosidad a 54 C (13 F). Los datos proporcionados son valores tipcos. Los valores exactos reales podrian tener una pequena variacion entre distintos motores. 177 Parker Hannifin Corporation

7 Radial Load / Radiale Wellenbelastung Charges Radiale / Carga Radial 11 Series HY /US,EU Radial Load - N (lb) (3) (25) 8896 (2) 6672 (15) 4448 (1) 2224 (5) Torque nm (lb-in) (1).9 (2) (3) (4) (5) -5.8 (-2) (-1) () 25.4 (1) 5.8 (2) 76.2 (3) Distance From Mounting Face - mm (in) The allowable side load curve is based on L 1 bushing life of 3 x RPM. Die zulassige radiale Wellenbelastung bezieht sich auf die Lager-Lebensdauer 3 x 1 6 Umdrehungen. L effort radial admissible sur l arbre depend a une duree de vie 3 x 1 6 de rotation. La curva de carga lateral admisible se basa en vida util de cojinete de 3 x 1 revoluciones. pp Series SD.p Parker Hannifin Corporation

8 Mounting,Ports/Gehäuse,nschlüße Carter,Orifices / Montaje,Lumbreras 11 Series HY /US,EU Code: M "L" SE 2-olt, Manifold 15.7 (.62) 28.5 (1.12) 11.2 (.44) 3.1 (.12) 2 x 14.2 (.56) 2x 31.8 (1.25) (.95) 2X 14.2 (.56) Ø (4.5) Ø (3.25) 13.3 (5.13) Max 16.4 (4.188) 7/16-2 STRIGHT THD O-RING CSE DRIN ø 2.62 (.812) x 2.3 (.8) Deep Motor with manifold mount is supplied with 2 O-rings. Zum Motor mit Universalanschluß werden 2 O-Ringe geliefert. Deux joints toriques sont livrés avec les moteurs a plan de raccordement universel. Il blocchetto connessioni é corredato da 2 OR. 2 X (1.255) 2x 22.9 (.9) 4x 5/16-18 UNC-2 x 12.7 (.5) Min Full Thread O-rings 2.62 (.812) 2.3 (.8) (.95) 59.9 (2.36) 58.5 (2.35) 117.1(4.61) (4.55) Code M Weight/Gewicht kg Poids/Peso (lb) (15.4) (16.2) (16.9) (17.5) (18.4) (19.1) (2.6) Length "L" mm "L" (in) (4.41) (4.6) (4.78) (4.98) (5.17) (5.42) (5.8) Code: S "L" SE 2-olt, 7/8-14 SE O-Ring 15.7 (.62) 28.5 (1.12) 11.2 (.44) 3.1 (.12) 2 x 25.4 (1.) (.95) 2X 14.2 (.56) Ø (4.5) Ø (3.25) 13.3 (5.13) Max 16.4 (4.188) 7/16-2 STRIGHT THD O-RING CSE DRIN 2 X (1.255) 7/8-14 SE O-Ring (.95) 59.9 (2.36) 58.5 (2.35) 117.1(4.61) (4.55) Code S Weight/Gewicht kg Poids/Peso (lb) (15.4) (16.2) (16.9) (17.5) (18.4) (19.1) (2.6) Length "L" mm "L" (in) (4.41) (4.6) (4.78) (4.98) (5.17) (5.42) (5.8) English equivalents for metric specifications are shown in ( ). pp Series SD.p Parker Hannifin Corporation

9 Mounting,Ports/Gehäuse,nschlüße Carter,Orifices / Montaje,Lumbreras 11 Series HY /US,EU Code: T SE 2-olt, 1/2 SPP Ø (4.5) 15.7 (.62) "L" 28.5 (1.12) 11.2 (.44) 3.1 (.12) 2 x 25.4 (1.) Ø (3.25) (.95) 2X 14.2 (.56) 13.3 (5.13) Max 16.4 (4.188) 7/16-2 STRIGHT THD O-RING CSE DRIN 1/2 SPP 2 X (1.255) (.95) 59.9 (2.36) 58.5 (2.35) 117.1(4.61) (4.55) Code T Weight/Gewicht kg Poids/Peso (lb) (15.4) (16.2) (16.9) (17.5) (18.4) (19.1) (2.6) Length "L" mm "L" (in) (4.41) (4.6) (4.78) (4.98) (5.17) (5.42) (5.8) Code: M SE 2-olt, Manifold Ø (4.5) "L" 29.2 (1.15) 14. (.55) 6.4 (.25) 15.7 (.62) 2 x 14.2 (.56) 2x 31.8 (1.25) Ø (3.999) (.95) 2X 14.2 (.56) (5.66) 176. (6.93) Max pp Series SD.p65 7/16-2 STRIGHT THD O-RING CSE DRIN ø 2.62 (.812) x 2.3 (.8) Deep 2 X (1.255) 2x 22.9 (.9) 4x 5/16-18 UNC-2 x 12.7 (.5) Min Full Thread Motor with manifold mount is supplied with 2 O-rings. O-rings Zum Motor mit Universalanschluß werden 2 O-Ringe geliefert. Deux joints toriques sont livrés avec les moteurs a plan de raccordement universel (.812) Il blocchetto connessioni é corredato da 2 OR. (.95) Code M Weight/Gewicht kg Poids/Peso (lb) (15.4) (16.2) (16.9) (17.5) (18.4) (19.1) (2.6) Length "L" mm "L" (in) (4.41) (4.6) (4.78) (4.98) (5.17) (5.42) (5.8) English equivalents for metric specifications are shown in ( ). 2.3 (.8) 6.2 (2.37) (2.35) 12.7 (4.75) (4.675) 18 Parker Hannifin Corporation

10 Mounting,Ports/Gehäuse,nschlüße Carter,Orifices / Montaje,Lumbreras 11 Series HY /US,EU Code: S "L" 29.2 (1.15) SE 2-olt, 7/8-14 SE O-Ring Ø (4.5) 15.7 (.62) 14. (.55) 6.4 (.25) 2x 25.4 (1.) Ø (3.999) (.95) 2X 14.2 (.56) (5.66) 176. (6.93) Max 7/16-2 STRIGHT THD O-RING CSE DRIN 2 X (1.255) 7/8-14 SE O-Ring (.95) Motor with manifold mount is supplied with 2 O-rings. O-rings Zum Motor mit Universalanschluß werden 2 O-Ringe geliefert. Deux joints toriques sont livrés avec les moteurs a plan de raccordement universel (.812) Il blocchetto connessioni é corredato da 2 OR. 2.3 (.8) 6.2 (2.37) (2.35) 12.7 (4.75) (4.675) Code S Weight/Gewicht kg Poids/Peso (lb) (15.4) (16.2) (16.9) (17.5) (18.4) (19.1) (2.6) Length "L" mm "L" (in) (4.41) (4.6) (4.78) (4.98) (5.17) (5.42) (5.8) English equivalents for metric specifications are shown in ( ). pp Series SD.p Parker Hannifin Corporation

11 Shafts / btriebswellen rbre / Ejes 11 Series HY /US,EU Code Code Code: 1" Keyed 45.5 (1.79) Code: 1 1" 6 Spline 45.5 (1.79) Code: 2 25mm Keyed 54.6 (2.15) Code: 3 1-1/4" Keyed 53.8 (2.12) English equivalents for metric specifications are shown in ( ). pp Series SD.p Parker Hannifin Corporation

12 Shafts / btriebswellen rbre / Ejes 11 Series HY /US,EU Code: 1" Keyed 18.6 (.73) Key 1/4 x 1 Woodruff #15 Per SE J (.251) ø (.999) 1/4-2 UNC thd x (.62) Min Deep 28.4 (1.12) Code: 1 1" 6 Spline 25.4 (1.) Min Full Spline SE 6 ø 25.3 (.996) 1/4-2 UNC thd x (.62) Min Deep ø (.995) Code: 2 25mm Keyed Key 8x7x32mm (1.629) (1.472) (.9843) (8mm) M8x1.25H-6H x16.(.63) Min Deep 2.9 (.826) Code: 3 1-1/4" Keyed 47.8 (1.88) 39.4 (1.55) x 7.95 (.313) ø (1.2495) 7.96 (.3135) 34.9 (1.373) 3/8-16 UNC thd x 19.5 (.75) Min Deep Key 7.95 x 31.5 (.313 x 1.24) Square English equivalents for metric specifications are shown in ( ). pp Series SD.p Parker Hannifin Corporation

13 11 Series HY /US,EU Code Code Code: 5 1-1/4"-14 Tooth Spline 53.8 (2.12) Code: 6 7/8"-13 Tooth Spline 45.5 (1.79) English equivalents for metric specifications are shown in ( ). pp Series SD.p Parker Hannifin Corporation

14 11 Series HY /US,EU Code: (1.88) 33. (1.3) Min Full Spline 1-1/4"-14 Tooth Spline ø (1.2265) 3/8-16 UNC thd x 19.5 (.75) Min Deep ø (1.247) Code: 6 7/8"-13 Tooth Spline 25.4 (1.) Min Full Spline 13 Tooth 16/32 1/4-2 UNC thd x (.62) Min Deep ø (.995) ø (.8725) 1/4-2 UNC-2 x 15.7 (.62) Min Full Thd English equivalents for metric specifications are shown in ( ). pp Series SD.p Parker Hannifin Corporation

Technical Information / Technische Information / Segni / Informacion Tecnica

Technical Information / Technische Information / Segni / Informacion Tecnica zm2 T Series / Serie / Série HY13-159-4/,EU 15 Displacements (2.2 24. in 3 /rev) 15 Schluckvolumen 36... 39 cm 3 /rev 15 Cylindrée