Hydraulic Motor & Brake

Transcription

1 SERIES MEDIUM DUTY Hydraulic Motor & rake RE

2 RE (ll Series) For Medium Duty pplications Overview series descriptions RE Series motors offer the perfect compromise between price and performance by producing work horse power at a reasonable cost. lthough these motors perform well in a wide range of applications, they are especially suited for low flow, high pressure applications. During startup, pressure causes the balance plate to flex toward the rotor, vastly improving volumetric efficiency. s the motor reaches operating pressure, the balance plate relaxes, allowing the rotor to turn freely which translates into higher mechanical efficiencies. Transmitting this power to the output shaft is the most durable drive link in its class. Four bearing options, combined with standard mounting flanges and output shafts, allow the motor to be configured to suit nearly any application. features / benefits High Pressure Shaft Seal offers superior seal life and performance and eliminates need for case drain. Three earing Options allow load carrying capability of motor to be matched to application. Heavy-Duty Drive Link is the most durable in its class and receives full flow lubrication to provide long life. Valve-In-Rotor Design provides cost effective, efficient distribution of oil and reduces overall motor length. Pressure-Compensated alance Plate improves volumetric efficiency at low flows and high pressure. typical applications Medium-duty wheel drives, augers, mixers, winch drives, swing drives, grapple heads, feed rollers, broom drives and more Specifications 500/501 - Hydraulic Motor Standard 530/531 - Hydraulic Motor With Heavy Duty earing 510/511 - Hydraulic Motor With Integral Drum rake 520/521 - Hydraulic Motor With Medium Duty earing 50/51 - Hydraulic Motor With Wheel Hub Speed Flow Torque Pressure CODE Displacement rpm lpm [gpm] Nm [lb-in] bar [psi] cm 3 [in 3 /rev] cont. inter. cont. inter. cont. inter. cont. inter. peak 121 [7.] [12] 61 [16] 327 [200] 383 [300] 207 [] 21 [0] 276 [] 162 [.] [16] 76 [20] 75 [] 52 [800] 207 [] 21 [0] 276 [] 20 [12.] [18] 83 [22] 52 [800] 633 [5600] 207 [] 21 [0] 276 [] 232 [1.2] [18] 83 [22] 6 [5700] 712 [6] 207 [] 21 [0] 276 [] 261 [15.] 76 [20] 1 [2] 712 [6] 71 [7000] 207 [] 21 [0] 276 [] [18.3] [22] 5 [25] 825 [7] 38 [8] 207 [] 21 [0] 276 [] 38 [21.2] [22] 5 [25] 21 [8150] 105 [250] 207 [] 21 [0] 276 [] [22.8] [20] 1 [2] 1006 [800] 1158 [10250] 207 [] 21 [0] 276 [] [28.3] 76 [20] 1 [2] 106 [700] 118 [1075] 172 [2500] 18 [2750] 207 [] [32.7] [20] 1 [2] 83 [8700] 123 [1] 138 [] 172 [2500] 207 [] [5.6] [20] 1 [2] 1062 [00] 1237 [1050] 103 [1500] 121 [1750] 138 [] Performance data is typical. Performance of production units varies slightly from one motor to another. Running at intermittent ratings should not exceed 10% of every minute of operation. 2 DELIVERING THE POWER TO GET WORK DONE

3 RE (ll Series) For Medium Duty pplications Displacement Performance Flow - lpm [gpm] Cont. Inter. Pressure - bar [psi] Cont. Inter. 17 [250] 35 [500] 6 [] 10 [1500] 138 [] 173 [2500] 207 [] 21 [0] 121 cm 3 [7. in 3 ] / rev Torque - Nm [lb-in], Speed rpm Intermittent Ratings - 10% of Operation 2 [0.5] [1] 8 [2] 15 [] 23 [6] 30 [8] 38 [10] 5 [12] 53 [1] 61 [16] 21 [187] 2 [215] 57 [500] 5 [7] [33] 111 [8] 10 [23] [872] 1 [807] 8 [75] 51 [8] 5 [7] 118 [103] 116 [1030] 116 [1023] 16 [17] 166 [16] 161 [128] 155 [1372] 15 [1283] 7 [85] 111 [86] 176 [155] 186 [162] 168 [183] 223 [173] 218 [130] 217 [118] 208 [185] 211 [186] 10 [123] 162 [12] 226 [17] 237 [20] 232 [2051] 283 [2505] 272 [211] 276 [2] 267 [2363] 272 [203] 225 [11] 271 [200] 278 [25] 27 [267] 326 [288] 325 [2878] 321 [283] 338 [22] 327 [287] 302 [2673] 335 [26] 328 [203] 385 [30] 385 [30] 385 [303] 33 [3036] 35 [317] 360 [3185] Rotor Overall Efficiency % 0-6% 0-3% Width Theoretical Torque - Nm [lb-in] 13.8 [.52] 33 [25] 67 [58] 133 [1178] [1768] 266 [2357] 333 [26] 3 [3535] 66 [12] Displacement tested at 5 C [12 F] with an oil viscosity of 6cSt [213 SUS] Theoretical rpm Flow - lpm [gpm] Cont. Inter. Pressure - bar [psi] Cont. Inter. 17 [250] 35 [500] 6 [] 10 [1500] 138 [] 173 [2500] 207 [] 21 [0] 162 cm 3 [. in 3 ] / rev Torque - Nm [lb-in], Speed rpm Intermittent Ratings - 10% of Operation 2 [0.5] [1] 8 [2] 15 [] 23 [6] 30 [8] 38 [10] 5 [12] 53 [1] 61 [16] 68 [18] 76 [20] 37 [326] 30 [26] 36 [317] 3 [32] 71 [631] 67 [56] 72 [60] 67 [56] 135 [110] 123 [1087] 108 [52] 105 [2] 77 [685] 80 [70] 80 [711] 75 [66] 158 [135] 16 [1] 1 [1323] 1 [1275] 228 [2022] 213 [188] 1 [176] 15 [1726] 1 [1323] 16 [18] 161 [123] 171 [1510] 235 [2078] 236 [200] 23 [207] 226 [18] 310 [273] 28 [263] 283 [2501] 280 [276] 223 [177] 2 [2158] 22 [213] 253 [221] 317 [2806] 312 [2760] 30 [2736] 30 [268] [3317] 368 [3253] 362 [3201] 3 [302] 310 [271] 32 [2865] 316 [272] 321 [2838] 38 [37] 385 [311] 376 [332] 36 [3270] 57 [00] 35 [387] 1 [3708] 53 [008] 3 [3088] 378 [33] 37 [3] 37 [3351] 62 [088] 56 [033] 55 [022] 0 [380] 51 [78] 502 [3] 2 [30] 81 [258] 51 [32] 518 [586] 513 [537] 522 [623] 7 [37] 551 [880] 516 [56] Rotor Overall Efficiency % 0-6% 0-3% Width Theoretical Torque - Nm [lb-in] 13.8 [.52] 5 [3] 8 [788] 178 [1576] 267 [2365] 356 [3153] 5 [31] 53 [72] 623 [5518] Displacement tested at 5 C [12 F] with an oil viscosity of 6cSt [213 SUS] Theoretical rpm Performance data is typical. Performance of production units varies slightly from one motor to another. DELIVERING THE POWER TO GET WORK DONE 3

4 RE (ll Series) For Medium Duty pplications Displacement Performance Flow - lpm [gpm] Cont. Inter. Pressure - bar [psi] Cont. Inter. 17 [250] 35 [500] 6 [] 10 [1500] 138 [] 173 [2500] 207 [] 21 [0] 20 cm 3 [12. in 3 ] / rev Torque - Nm [lb-in], Speed rpm Intermittent Ratings - 10% of Operation 2 [0.5] [1] 8 [2] 15 [] 23 [6] 30 [8] 38 [10] 5 [12] 53 [1] 61 [16] 68 [18] 76 [20] 83 [22] 0 [358] 3 [376] [385] 3 [37] 82 [72] 80 [70] 66 [581] 165 [162] 150 [1328] 13 [1183] 121 [1068] 110 [70] 11 [168] 1 [808] 85 [753] 3 [851] [83] 11 [16] 188 [1661] 180 [152] 261 [2312] 273 [213] 253 [222] 232 [2056] 206 [1823] 285 [2520] 133 [1181] [176] 15 [1727] 18 [1752] 28 [2518] 285 [2518] 276 [25] 362 [3] 368 [3253] 335 [26] 33 [3] 308 [2725] 37 [3353] 2 [2] 276 [22] 2 [266] 305 [2701] 38 [36] 02 [3556] 36 [322] 50 [382] [] 35 [3850] 16 [3686] 01 [3552] 86 [303] [3323] 373 [330] 37 [3311] 01 [35] 63 [08] 58 [053] 58 [051] 535 [731] 558 [36] 52 [63] 512 [532] 507 [8] 2 [315] 61 [07] 77 [222] 553 [8] 53 [802] 535 [737] 618 [571] 602 [5328] 58 [522] 5 [52] 526 [656] 52 [72] 5 [818] 636 [5628] 628 [555] 615 [51] 616 [551] 62 [5568] Rotor Overall Efficiency % 0-6% 0-3% Width Theoretical Torque - Nm [lb-in] 17.3 [.682] 56 [] 112 [87] 223 [175] 335 [262] 6 [3] 558 [36] 66 [52] 781 [611] Displacement tested at 5 C [12 F] with an oil viscosity of 6cSt [213 SUS] Theoretical rpm Flow - lpm [gpm] Cont. Inter. Pressure - bar [psi] Cont. Inter. 17 [250] 35 [500] 6 [] 10 [1500] 138 [] 173 [2500] 207 [] 21 [0] 233 cm 3 [1.2 in 3 ] / rev Torque - Nm [lb-in], Speed rpm Intermittent Ratings - 10% of Operation 2 [0.5] 5 [37] 2 [813] 18 [1628] 23 [250] [3323] [1] 8 [2] 101 [80] 223 [172] 316 [273] 1 [3660] 3 [366] 560 [55] [2] 51 [53] 105 [26] 215 [18] 32 [211] 25 [3760] 52 [637] 618 [568] 710 [6286] [] 3 [38] 108 [60] 20 [1851] 326 [288] 35 [386] 53 [771] 655 [57] 721 [6381] [6] 102 [603] 213 [188] 33 [1] 28 [378] 536 [77] 628 [555] 718 [6355] [8] 8 [78] 207 [1830] 316 [273] 25 [3762] 521 [612] 63 [5653] 717 [631] [10] 78 [60] 18 [1750] 311 [2752] 36 [3856] 527 [660] 612 [520] 703 [6218] [12] 18 [166] 26 [262] 25 [376] 510 [517] 5 [530] 68 [608] [1] 177 [1565] 23 [256] 388 [33] 5 [38] 587 [517] 680 [6017] [16] 150 [1326] 272 [208] 37 [] 8 [280] 57 [5077] 66 [525] [18] 12 [1261] 26 [2333] 355 [310] 3 [366] 56 [5032] 655 [57] [20] 122 [1083] 237 [206] 37 [3068] 53 [00] 571 [5057] [22] 210 [1855] 338 [287] 6 [10] 550 [86] Rotor Overall Efficiency % 0-6% 0-3% Width Theoretical Torque - Nm [lb-in] 1.7 [.777] 6 [565] 128 [1131] 256 [2261] 383 [332] 511 [522] 63 [5653] 767 [6783] 8 [71] Displacement tested at 5 C [12 F] with an oil viscosity of 6cSt [213 SUS] Performance data is typical. Performance of production units varies slightly from one motor to another. Theoretical rpm DELIVERING THE POWER TO GET WORK DONE

5 RE (ll Series) For Medium Duty pplications Displacement Performance Flow - lpm [gpm] Cont. Inter. Pressure - bar [psi] Cont. Inter. 17 [250] 35 [500] 6 [] 10 [1500] 138 [] 173 [2500] 207 [] 21 [0] 261 cm 3 [15. in 3 ] / rev Intermittent Ratings - 10% of Operation Torque - Nm [lb-in], Speed rpm [32] 112 [8] 2 [0.5] [1] 15 8 [2] [] 5 23 [6] [8] [10] 16 5 [12] [1] [16] [18] [20] [22] [2] 3 Overall Efficiency % 0-6% 0-3% Rotor Width Theoretical Torque - Nm [lb-in] [633] 13 [1266] 286 [2532] 2 [378] 572 [506] 715 [6330] 858 [756] 1001 [8861] [.872] Displacement tested at 5 C [12 F] with an oil viscosity of 6cSt [213 SUS] 5 [75] 5 [7] [2] 5 [37] [833] 85 [752] 78 [62] 6 [563] 182 [8] [117] 136 [] 132 [1168] 82 [722] 113 [8] 115 [1021] 11 [1010] 115 [1016] 227 [8] 231 [20] 217 [11] 18 [175] 2 [26] 30 [263] 278 [] 263 [2325] 227 [] 20 [2125] 27 [218] 261 [7] 236 [200] 38 [3078] 30 [3013] 35 [3135] 326 [2886] 8 [365] 17 [360] 31 [36] 37 [331] 361 [310] 365 [3] 367 [32] 363 [321] 36 [3221] 77 [22] 70 [155] 6 [108] 5 [31] 552 [88] 550 [870] 521 [61] 512 [535] 6 [386] 78 [227] 88 [318] 86 [] 7 [38] 52 [523] 585 [5180] 567 [5018] 568 [5026] 651 [5763] 63 [568] 636 [5628] 615 [52] 578 [5112] 51 [5] 55 [5268] 50 [5225] 62 [6128] 685 [6063] 672 [55] 668 [508] 752 [665] 70 [6551] 736 [6516] 68 [5736] 703 [6223] 67 [6171] 721 [637] 7 [7027] 76 [708] 802 [705] 765 [6771] 807 [713] 802 [706] Theoretical rpm Flow - lpm [gpm] Cont. Inter. Pressure - bar [psi] Cont. Inter. 17 [250] 35 [500] 6 [] 10 [1500] 138 [] 173 [2500] 207 [] 21 [0] cm 3 [18.3 in 3 ] / rev Intermittent Ratings - 10% of Operation Torque - Nm [lb-in], Speed rpm 51 [52] 5 [83] 2 [0.5] [1] 13 8 [2] [] [6] [8] [10] [12] [1] [16] [18] [20] [22] [2] [25] 316 Overall Efficiency % 0-6% 0-3% Rotor Width Theoretical Torque - Nm [lb-in] [72] 165 [157] 32 [21] [371] 65 [5828] 823 [7285] 88 [872] 1152 [101] [1.000] Displacement tested at 5 C [12 F] with an oil viscosity of 6cSt [213 SUS] 63 [557] 62 [551] 66 [588] 58 [511] 6 [05] 111 [81] 2 [81] 77 [68] 63 [553] 201 [1780] 172 [1522] 1 [1276] 11 [10] 105 [28] 15 [1282] 158 [100] 15 [1281] 10 [121] 128 [1136] 282 [23] 261 [2313] 25 [2165] 22 [183] 33 [2] 327 [285] 321 [2836] 281 [283] 262 [231] 302 [2675] 308 [2722] 316 [273] 20 [2566] 305 [26] 0 [3623] 388 [335] 31 [36] 366 [323] 67 [135] 80 [27] 66 [127] 35 [3853] 3 [3838] 33 [382] 37 [3866] 30 [3805] 2 [5] 31 [360] 503 [7] 72 [177] 530 [687] 508 [8] 666 [588] 611 [510] 575 [508] 55 [3] 553 [8] 510 [513] 571 [5056] 577 [5107] 56 [830] 571 [5056] 683 [603] 61 [5676] 661 [588] 633 [55] 80 [7115] 75 [656] 732 [67] 703 [6223] 707 [6257] 627 [5552] 67 [6011] 680 [6015] 60 [6105] 700 [61] 7 [7028] 783 [627] 80 [7157] 76 [70] 8 [755] 10 [8051] 768 [676] 820 [7258] 801 [7088] 826 [7313] 1 [8131] 881 [77] [838] 16 [8103] 830 [736] 08 [800] 6 [8372] 30 [8233] Theoretical rpm Performance data is typical. Performance of production units varies slightly from one motor to another. DELIVERING THE POWER TO GET WORK DONE 5

6 RE (ll Series) For Medium Duty pplications Displacement Performance Flow - lpm [gpm] Cont. Inter. Pressure - bar [psi] Cont. Inter. 17 [250] 35 [500] 6 [] 10 [1500] 138 [] 173 [2500] 207 [] 21 [0] 38 cm 3 [21.2 in 3 ] / rev Torque - Nm [lb-in], Speed rpm Intermittent Ratings - 10% of Operation 2 [0.5] [1] 8 [2] 15 [] 23 [6] 30 [8] 38 [10] 5 [12] 53 [1] 61 [16] 68 [18] 76 [20] 83 [22] 1 [2] 5 [25] 6 [566] 6 [570] 6 [607] 71 [627] 62 [5] 53 [72] 113 [100] 8 [86] 86 [758] 63 [560] 220 [18] 208 [183] 17 [1583] 172 [1526] 36 [326] 13 [1183] 13 [118] 15 [1285] 151 [130] 1 [1618] 13 [1233] 28 [263] 265 [236] 252 [2226] 235 [207] 3 [30] [3320] 352 [3112] 360 [3186] 52 [682] 272 [20] 26 [261] 312 [276] 313 [2767] 315 [2788] 307 [2713] 31 [381] 5 [336] 22 [3738] 0 [361] 571 [505] 513 [5] 55 [06] 53 [72] 67 [5730] 3 [3532] 37 [386] 62 [02] 71 [16] 7 [11] 5 [058] 601 [5317] 581 [51] 570 [50] 5 [85] 63 [613] 683 [60] 685 [606] 666 [580] 600 [5308] 630 [5577] 630 [5577] 626 [5537] 75 [653] 70 [6552] 723 [638] 720 [6] 83 [728] 835 [7385] 813 [718] 72 [6571] 772 [683] 768 [676] 768 [673] 10 [8056] 81 [788] 881 [77] 850 [7522] 86 [8727] 75 [8632] 58 [882] 855 [756] 88 [786] 25 [8182] 28 [8210] 1062 [3] 10 [237] 1031 [126] 1012 [852] 3 [8785] 1032 [137] 1051 [] Rotor Overall Efficiency % 0-6% 0-3% Width Theoretical Torque - Nm [lb-in] 3. [1.553] 5 [8] 11 [1688] 381 [3376] 572 [506] 763 [6752] 5 [83] 11 [10127] 1335 [11815] Displacement tested at 5 C [12 F] with an oil viscosity of 6cSt [213 SUS] Theoretical rpm Flow - lpm [gpm] Cont. Inter. Pressure - bar [psi] Cont. Inter. 17 [250] 35 [500] 6 [] 10 [1500] 138 [] 173 [2500] 207 [] 21 [0] cm 3 [22.8 in 3 ] / rev Torque - Nm [lb-in], Speed rpm Intermittent Ratings - 10% of Operation 2 [0.5] 76 [67] 3 6 [1] 8 [75] 162 [132] 32 [211] 0 [337] 63 [5652] 763 [6756] [2] 82 [72] 171 [1510] 361 [[316] 537 [75] 68 [605] 836 [73] 55 [8] [] 77 [680] 163 [13] 358 [316] 537 [756] 65 [6151] 857 [7587] 8 [8750] 1121 [23] [6] 67 [55] 158 [138] 35 [3130] 527 [661] 65 [6155] 86 [762] 1011 [851] 1168 [1033] [8] 57 [508] 1 [1321] 30 [3010] 510 [512] 65 [615] 85 [776] 100 [830] 1156 [1022] [10] 13 [1187] 322 [28] 5 [383] 681 [602] 836 [73] 1007 [813] 1157 [10235] [12] 115 [1013] 301 [2661] 80 [2] 65 [5711] 80 [715] 80 [867] 111 [1008] [1] 3 [81] 280 [275] 77 [218] 633 [5602] 75 [7036] [802] 1117 [887] [16] 73 [66] 261 [231] 2 [377] 58 [526] 770 [6817] 3 [8267] 1085 [605] [18] 236 [201] 3 [383] 57 [5282] 765 [6771] 07 [8026] 1080 [55] [20] 20 [1851] 38 [336] 561 [6] 70 [65] 877 [776] 1027 [01] [22] 178 [1576] 37 [330] 530 [6] 66 [6] 80 [731] [2] 11 [126] 31 [2822] 511 [523] 662 [5860] Overall Efficiency % 0-6% 0-3% Rotor Performance data is typical. Performance Width Theoretical Torque - Nm [lb-in] of production units varies slightly from one motor to another [08] 205 [1815] 10 [3631] 615 [56] 821 [7261] 1026 [076] 1231 [1082] 136 [12707] [1.252] Displacement tested at 5 C [12 F] with an oil viscosity of 6cSt [213 SUS] 6 DELIVERING THE POWER TO GET WORK DONE Theoretical rpm

7 RE (ll Series) For Medium Duty pplications Displacement Performance Flow - lpm [gpm] Cont. Inter. 70 Pressure - bar [psi] Cont. 17 [250] 35 [500] 6 [] 10 [1500] 138 [] 173 [2500] 207 [] 65 cm 3 [28.3 in 3 ] / rev Intermittent Ratings - 10% of Operation Torque - Nm [lb-in], Speed rpm 3 [823] 185 [1635] 2 [0.5] [1] 8 [865] 20 [185] 35 [3851] 65 [5836] 855 [7563] 1025 [071] 116 [10586] 8 [2] [83] [177] [332] 65 [582] 886 [7836] 1066 [3] 1250 [11062] 15 [] [75] 13 [170] 38 [3880] 673 [555] 872 [7715] 1073 [] 1258 [11128] 23 [6] [63] 17 [1587] 2 [2] 663 [5863] 857 [7586] 108 [718] 127 [11317] 30 [8] [6] 16 [155] 07 [357] 627 [5550] 851 [7533] 1067 [] 1276 [11288] 38 [10] [128] 37 [3] 630 [5575] 832 [7363] 1067 [1] 1273 [1126] 5 [12] [1006] [30] 580 [5133] 802 [7101] 1013 [86] 1222 [10817] 53 [1] [16] [18] [20] [22] [2] 16 Overall Efficiency % 0-6% 0-3% Rotor Width Theoretical Torque - Nm [lb-in] [1127] 255 [2253] 50 [506] 76 [6760] 1018 [013] 1273 [11266] 1528 [1351] [1.553] Displacement tested at 5 C [12 F] with an oil viscosity of 6cSt [213 SUS] 7 [857] 83 [736] 56 [7] 235 [2078] 202 [170] 157 [132] 203 [17] 322 [286] 275 [23] 7 [23] 60 [075] 385 [310] 0 [3618] 55 [81] 526 [657] 706 [62] 66 [520] 620 [58] 610 [502] 76 [700] 737 [651] 17 [8117] 883 [7811] 83 [76] 815 [720] 65 [8538] 56 [86] 1122 [33] 110 [10528] 1166 [10317] Peak Theoretical rpm Flow - lpm [gpm] Cont. Inter. 50 Pressure - bar [psi] Cont. Inter. 17 [250] 35 [500] 6 [] 10 [1500] 138 [] 173 [2500] 536 cm 3 [32.7 in 3 ] / rev Intermittent Ratings - 10% of Operation Torque - Nm [lb-in], Speed rpm 10 [21] 17 [178] 2 [0.5] 2 2 [1] 8 8 [2] 15 [1058] 232 [2055] 510 [510] 757 [667] 88 [870] 1223 [10827] 15 [] [85] 22 [18] 505 [6] 783 [630] 3 [8787] 1225 [10838] 23 [6] [62] 213 [1887] 8 [285] 750 [6635] 83 [868] 1251 [11075] 30 [8] [523] 10 [1678] 55 [026] 728 [65] 5 [887] 12 [11008] 38 [10] [155] 38 [387] 71 [6360] 5 [8360] 3 [1066] 5 [12] [1] 61 [16] [18] [20] [22] [2] 170 Overall Efficiency % 0-6% 0-3% Rotor Width Theoretical Torque - Nm [lb-in] [1302] 2 [] 588 [5207] 883 [7811] 1177 [101] 171 [13018] [1.71] Displacement tested at 5 C [12 F] with an oil viscosity of 6cSt [213 SUS] 126 [1111] 13 [118] 13 [1233] 10 [63] 83 [736] 323 [2861] 27 [262] 215 [105] [2031] 20 [2] 18 [3703] 385 [307] 356 [315] 603 [5333] 537 [753] 1 [3] 67 [136] 501 [36] 682 [6035] 668 [508] 612 [517] 82 [7335] 72 [7011] 750 [663] 6 [6183] 755 [667] 52 [821] 8 [757] 86 [76] 110 [816] 3 [8310] 77 [866] 1183 [1067] 1163 [1020] 1116 [876] 11 [10165] 1185 [108] Theoretical rpm Performance data is typical. Performance of production units varies slightly from one motor to another. DELIVERING THE POWER TO GET WORK DONE 7

8 RE (ll Series) For Medium Duty pplications Displacement Performance Flow - lpm [gpm] Cont. Inter. 750 Pressure - bar [psi] Cont. 17 [250] 35 [500] 6 [] 10 [1500] 138 [] 78 cm 3 [5.6 in 3 ] / rev Intermittent Ratings - 10% of Operation Torque - Nm [lb-in], Speed rpm 17 [12] 281 [287] 2 [0.5] [137] 322 [2852] 652 [5768] 67 [855] 1308 [11571] [1] [103] 33 [3] 63 [613] 1027 [088] 1360 [33] 8 [2] [1] 331 [233] 705 [621] 106 [1] 116 [1253] 15 [] [11] 321 [280] 67 [6166] 105 [373] 108 [1262] 23 [6] [1008] 30 [] 678 [6002] 103 [17] 121 [12573] 30 [8] [722] 271 [235] 68 [5733] 1015 [880] 1371 [12130] 38 [10] [77] 2 [2207] 616 [552] 83 [86] 135 [1102] 5 [12] [1] [1325] 533 [718] 05 [8008] 1271 [112] 61 [16] [27] [37] 860 [761] 1225 [1083] 68 [18] [20] [22] [2] 122 Overall Efficiency % 0-6% 0-3% Rotor Width Theoretical Torque - Nm [lb-in] [1815] 10 [3631] 821 [7261] 1231 [1082] 161 [1522] [2.501] Displacement tested at 5 C [12 F] with an oil viscosity of 6cSt [213 SUS] 17 [173] 62 [552] 385 [30] 302 [266] 577 [510] 23 [371] 77 [6608] 670 [532] 6 [8372] 805 [7123] 1311 [10] 1173 [10385] Peak Theoretical rpm Performance data is typical. Performance of production units varies slightly from one motor to another. 8 DELIVERING THE POWER TO GET WORK DONE

9 RE (500/501 Series) Hydraulic Motor housings Dimensions shown are without paint. Paint thickness can be up to 0.13 [.005]. -HOLE, MGNETO MOUNT, LIGNED PORTS 31 7/8-1 UNF 38 G 1/2 STNDRD II 71 [2.80] 66 [2.58] [2.7] Min. 18 [.70] 3.0 [.] 2.8 [.110] 61 [2.3] 137 [5.38] 82.6 [3.250] 82.5 [3.27] [.] [.6] 3 [.12] Ø [.187] 13.3 [.52] 13.1 [.51] 2 [.06] OPTIONL VLVE CVITY 6 [2.52] F E 23 [.1] 60 [2.35] Min. Ø31 [1.2] Spot Face 107 [.21] E: 10 Series/2-Way Valve Cavity 7/8-1 UNF F: Valve Cartridge Installed 6-HOLE, SE MOUNT, LIGNED PORTS 51 7/8-1 UNF 58 G 1/2 II 71 [2.80] 66 [2.58] [2.7] Min. 18 [.70] 3.0 [.] 2.8 [.110] 61 [2.3] 137 [5.38] 82.6 [3.250] 82.5 [3.27] [.] [.6] 3 [.12] Ø [.187] Dimension II is charted on page [.52] 13.1 [.51] 2 [.06] DELIVERING THE POWER TO GET WORK DONE

10 RE (500/501 Series) Hydraulic Motor housings Dimensions shown are without paint. Paint thickness can be up to 0.13 [.005]. -HOLE, WHEEL MOUNT, LIGNED PORTS W31 7/8-1 UNF W38 G 1/2 STNDRD 13.3 [.52] 13.1 [.51] 132 [5.21] 63 [2.7] Min..3 [1.75].2 [1.71] 1 [.76] 5 [.20] JJ 37 [1.5] 3 [.10] Min. 138 [5.5] 82.6 [3.250] 82.5 [3.27] 82 [3.23] [.] 126. [.5] 5 Ø 17.6 [5.812] OPTIONL VLVE CVITY 18 [.72] 2 [1.1] E F 57 [.25] 105 [.13] Ø31 [1.2] Spot Face E: 10 Series/2-Way Valve Cavity 7/8-1 UNF F: Valve Cartridge Installed Dimension JJ is charted on page DELIVERING THE POWER TO GET WORK DONE

11 RE (500/501 Series) Hydraulic Motor technical information llowable Shaft Load / earing curve The bearing curve represents allowable bearing loads based on ISO 281 bearing capacity for an L 10 life of 2,000 hours at 100 rpm. Radial loads for speeds other than 100 rpm may be calculated using the multiplication factor table below. length & weight chart Dimensions II & JJ are the overall motor lengths from the rear of the motor to the mounting flange surface and are referenced on detailed housing drawings listed on pages & 10. II # Length 162 [6.37] 162 [6.37] 165 [6.51] 168 [6.61] Weight kg [lb] 10.6 [23.] 10.6 [23.] 11.0 [2.2] 11.1 [2.] MGNETO & SE MOUNTS mm 170 [6.70] 17 [6.83] 187 [7.38] 180 [7.08] 11.3 [25.0] 11.7 [25.8] 12.8 [28.2] 12.2 [27.0] [7.38] 1 [7.62] 12.8 [28.2] 13.3 [2.] [8.33] 1.8 [32.5] JJ # Length [.72] Weight kg [lb] 11.7 [25.8] [.72] 123 [.86] 11.7 [25.8] 12.1 [26.6] lb ERING SHFT 3 in dan ll RE series motor weights can vary ± 0.5 kg [1 lb] depending on model configurations such as housing, shaft, endcover, options etc [.5] 128 [5.05] 132 [5.18] 16 [5.73] 138 [5.3] 16 [5.73] 152 [5.7] 170 [6.68] 12.2 [26.8] 12. [27.] 12.8 [28.2] 13. [30.6] 13.3 [2.] 13. [30.6] 1. [31.8] 15.8 [3.] WHEEL MOUNTS mm SHFT ERING LOD MULTIPLICTION FCTOR TLE RPM FCTOR RPM FCTOR ERING 500 lb in dan DELIVERING THE POWER TO GET WORK DONE 11

12 RE (500/501 Series) Hydraulic Motor Shafts Spline Spline Extended 10 1 Straight 15 1 Straight Extended 6 Spline SE J Standard 25 [1.00] KK 0 [1.58] 6. [.251] 6. [.250] 25. [1.020] 2.6 [.70] 5 [.18] KK 0 [1.58] Ø25.3 [.6] Ø25.2 [.2] 28.2 [1.110] 28.0 [1.101] Ø25. [.] Ø25.3 [.8] 5/16-18 UNC, Min. Depth 18 [.70] 5/16-18 UNC, Min. Depth 18 [.70] Torque: 678 Nm [6000 lb-in] / Straight Extended / Straight Torque: 655 Nm [5800 lb-in] 12 25mm Straight KK 5 [2.1] KK 8.0 [.31] 8.0 [.313] 8 [.33] 8 [1.0] 37.5 [1.75] 36.2 [1.25] 8.0 [.31] 8.0 [.313] 30. [1.218] 2.7 [1.168] 5 [.21] 6 [1.83] 35.3 [1.388] 35.0 [1.376] 31.8 [1.250] 31.7 [1.2] 28.0 [1.102] 27.7 [1.01] Ø25.0 [.8] Ø25.0 [.83] 5/8-18 UNF, Min. Depth 21 [.83] M8x1.25, Min. Depth 16 [.63] Torque: 1 Nm [10600 lb-in] 08 32mm Straight Extended 21 32mm Straight Torque: 678 Nm [6000 lb-in] / Tapered / Tapered Extended KK KK 5 [2.1] 35 [1.37] 10.0 [.3] 10.0 [.32] 12 [.6] 8 [1.0] 32.6 [1.285] 31. [1.235] 8.0 [.31] 1 [.75] 8.0 [.313] 2.3 [.57] 5 [.20] 23.0 [.07] 3.8 [1.372] 3.5 [1.35] 32.0 [1.] 32.0 [1.25] [.15] 31.8 [1.250] 31.7 [1.2] Torque: 1 Nm [10600 lb-in] M8x1.25, Min. Depth 16 [.63] Torque: 1 Nm [10600 lb-in] Ø [.17] 1:8 Taper slotted hex nut is standard on this shaft. 0 1 Tooth Spline Extended 23 1 Tooth Spline mounting / shaft length chart 1 Tooth Spline 12/2 Pitch Standard NSI Spline 33 [1.31] Wire Ring Torque: 1 Nm [10600 lb-in] 31.7 [1.2] 31.6 [1.25] KK 5 [2.1] 8 [1.0] 1 [1.60] 5/8-18 UNF, Min. Depth 21 [.83] Ø2 [.06] Dimension KK is the overall distance from the motor mounting surface to the end of the shaft and is referenced on detailed shaft drawings above. Shaft lengths vary ± 0.8 mm [.030 in.] KK # Magneto & Mounts 50 [1.7] 76 [3.01] 88 [3.5] 88 [3.5] 88 [3.5] 50 [1.7] 56 [2.21] 76 [3.01] 61 [2.1] 61 [2.1] 66 [2.58] 61 [2.1] 2 [3.62] Wheel Mounts 1 [3.60] 118 [.6] 12 [5.0] 12 [5.0] 12 [5.0] 1 [3.60] 8 [3.8] 118 [.6] 103 [.05] 103 [.05] 107 [.22] 103 [.05] 13 [5.26] 12 DELIVERING THE POWER TO GET WORK DONE

13 RE (500/501 Series) Hydraulic Motor ordering information CHOOSE SERIES DESIGNTION 5. SELECT PINT OPTION 500 Counterclockwise Rotation 501 Clockwise Rotation C lack lack, Unpainted Mounting Surface No Paint 6. SELECT VLVE CVITY / CRTRIDGE OPTION The 500 & 501 series are bi-directional. Reversing the inlet hose will reverse shaft rotation. For applications requiring the motor to rotate in only one direction, shaft seal life may be prolonged by pressurizing the port of the motor. 2. SELECT DISPLCEMENT OPTION 121 cm 3 /rev [7. in 3 /rev] 162 cm 3 /rev [. in 3 /rev] 20 cm 3 /rev [12. in 3 /rev] 232 cm 3 /rev [1.2 in 3 /rev] 261 cm 3 /rev [15. in 3 /rev] cm 3 /rev [18.3 in 3 /rev] 3. SELECT MOUNT & PORT OPTION W31 W Hole, Magneto Mount, ligned Ports, 7/8-1 UNF -Hole, Magneto Mount, ligned Ports, G 1/2 6-Hole, SE Mount, ligned Ports, 7/8-1 UNF 6-Hole, SE Mount, ligned Ports, G 1/2 -Hole, Wheel Mount, ligned Ports, 7/8-1 UNF -Hole, Wheel Mount, ligned Ports, G 1/2 38 cm 3 /rev [21.2 in 3 /rev] cm 3 /rev [22.8 in 3 /rev] 65 cm 3 /rev [28.3 in 3 /rev] 536 cm 3 /rev [32.7 in 3 /rev] 78 cm 3 /rev [5.6 in 3 /rev] C D None Valve Cavity Only 6 bar [ psi] Relief 86 bar [1250 psi] Relief E F G 10 bar [1500 psi] Relief 121 bar [1750 psi] Relief 138 bar [ psi] Relief Valve cavity is not available on the 51 & 58 housings. 7. SELECT N DD-ON OPTION Standard Lock Nut C Solid Hex Nut W Speed Sensor, Dual, -Pin Male Weatherpack Connector X Speed Sensor, Dual, -Pin M12 Male Connector Y Speed Sensor, Single, 3-Pin Male Weatherpack Connector Z Speed Sensor, Single, -Pin M12 Male Connector 8. SELECT MISCELLNEOUS OPTION None C Freeturning Rotor E Hydraulic Declutch With Freeturning Rotor Speed sensor option is not available with wheel mounts. SELECT SHFT OPTION Spline 1 6 Spline Extended 1-1/ Straight Extended 32mm Straight Extended 1 Tooth Spline Extended 1 Straight 25mm Straight Straight Extended 1-1/ Straight 32mm Straight 1-1/ Tapered 1 Tooth Spline 1-1/ Tapered Extended Extended shafts are designed for use with one of the speed sensor options listed in STEP 7. DELIVERING THE POWER TO GET WORK DONE 13

14 RE (520/521 Series) Hydraulic Motor With Medium Duty earing housings Dimensions shown are without paint. Paint thickness can be up to 0.13 [.005]. 6-HOLE, SE MOUNT, LIGNED PORTS 51 7/8-1 UNF 58 G 1/2 71 [2.80] 66 [2.58] [2.7] Min. 1 [.73] 3.0 [.] 2.8 [.110] 86 [3.0] LL 137 [5.38] 82.6 [3.250] 82.5 [3.27] 13.3 [.52] 13.1 [.51] Ø [.187] 3 [.12] 2 [.06] 6-HOLE, SE MOUNT, LIGNED MNIFOLD PORTS 57 1/2 Drilled LL 71 [2.80] [2.8] Min. 1 [.73] 3.0 [.] 2.8 [.110] 86 [3.0] 1 [.56] 1 [.56] 2 [.07] 137 [5.38] 82.6 [3.250] 82.5 [3.27] 17 [.68] 3 [.12] 13.3 [.52] 13.1 [.51] Ø [.187] 2 [.06] () M8x1.25, Min. Depth 13 [.50] -HOLE, WHEEL MOUNT, LIGNED PORTS W31 7/8-1 UNF W38 G 1/2 133 [5.23] 70 [2.76] 13.3 [.52] 13.1 [.51] 62 [2.5] Min. 1 [.76] 20 [.78] MM 37 [1.] 3 [.10] Min. 11 [5.56] 5.3 [3.750] 5.2 [3.78] 8 [3.50] [.] 126. [.5] 22.5 Ø 17.6 [5.812] Dimensions LL & MM are charted on page DELIVERING THE POWER TO GET WORK DONE

15 RE (520/521 Series) Hydraulic Motor With Medium Duty earing technical information llowable Shaft Load / earing curve The bearing curve represents allowable bearing loads based on ISO 281 bearing capacity for an L 10 life of 2,000 hours at 100 rpm. Radial loads for speeds other than 100 rpm may be calculated using the multiplication factor table on page 11. SE MOUNTS mm 500 length & weight chart Dimensions LL & MM are the overall motor lengths from the rear of the motor to the mounting flange surface and are referenced on detailed housing drawings listed on page 1. LL # Length 187 [7.37] 187 [7.37] 11 [7.51] 13 [7.61] 16 [7.70] 1 [7.83] 213 [8.38] 205 [8.08] 213 [8.38] 21 [8.62] 237 [.33] Weight kg [lb] 13.3 [2.] 13.3 [2.] 13.7 [30.2] 13.8 [30.] 1.1 [31.0] 1. [31.8] 15.5 [3.2] 15.0 [33.0] 15.5 [3.2] 16.1 [35.] 17.5 [38.5] lb ERING -3 * SHFT 3 in dan ll RE series motor weights can vary ± 0.5 kg [1 lb] depending on model configurations such as housing, shaft, endcover, options etc. MM # Length [.72] [.72] 123 [.86] 126 [.5] 128 [5.05] 132 [5.18] 16 [5.73] 138 [5.3] 16 [5.73] 152 [5.7] 170 [6.68] Weight kg [lb] 12. [28.] 12. [28.] 13.2 [2.2] 13.3 [2.] 13.6 [30.0] 1.0 [30.8] 15.1 [33.2] 1.5 [32.0] 15.1 [33.2] 15.6 [3.] 17.0 [37.5] WHEEL MOUNTS mm SHFT ERING lb in dan DELIVERING THE POWER TO GET WORK DONE 15

16 RE (520/521 Series) Hydraulic Motor With Medium Duty earing Shafts Spline 0 1 Tooth Spline NN NN 5 [2.1] 6 Spline SE J Standard 25 [1.00] 0 [1.58] 1 Tooth Spline 12/2 Pitch Standard NSI Spline 8 [1.0] 1 [1.60] Ø25.3 [.6] Ø25.2 [.2] 33 [1.31] Wire Ring 31.7 [1.2] 31.6 [1.25] 5/16-18 UNC, Min. Depth 18 [.70] 5/8-18 UNF, Min. Depth 21 [.83] Ø2 [.06] Torque: 678 Nm [6000 lb-in] / Straight Torque: 1 Nm [10600 lb-in] 15 1 Straight 8.0 [.31] 8.0 [.313] 8 [.33] NN 5 [2.1] NN 8 [1.0] 0 [1.58] 37.5 [1.75] 25. [1.020] 36.2 [1.25] 6. [.251] 2.6 [.70] 6. [.250] 5 [.18] 35.3 [1.388] 35.0 [1.376] 31.8 [1.250] 31.7 [1.2] 28.2 [1.110] 28.0 [1.101] Ø25. [.] Ø25.3 [.8] 5/8-18 UNF, Min. Depth 21 [.83] 5/16-18 UNC, Min. Depth 18 [.70] Torque: 1 Nm [10600 lb-in] Torque: 655 Nm [5800 lb-in] 08 32mm Straight / Tapered NN NN 5 [2.1] 35 [1.37] 10.0 [.3] 10.0 [.32] 12 [.6] 8 [1.0] 32.6 [1.285] 31. [1.235] 8.0 [.31] 1 [.75] 8.0 [.313] 2.3 [.57] 5 [.20] 23.0 [.07] 3.8 [1.372] 3.5 [1.35] 32.0 [1.] 32.0 [1.25] [.15] 31.8 [1.250] 31.7 [1.2] Torque: 1 Nm [10600 lb-in] M8x1.25, Min. Depth 16 [.63] Torque: 1 Nm [10600 lb-in] Ø [.17] 1:8 Taper slotted hex nut is standard on this shaft. mounting / shaft length chart Dimension NN is the overall distance from the motor mounting surface to the end of the shaft and is referenced on detailed shaft drawings above. Shaft lengths vary ± 0.8 mm [.030 in.] NN # SE Mounts 51 [2.02] 63 [2.7] 62 [2.7] 63 [2.7] 51 [2.02] 67 [2.63] Wheel Mounts 11 [.6] 131 [5.15] 130 [5.15] 131 [5.15] 11 [.6] 135 [5.31] 16 DELIVERING THE POWER TO GET WORK DONE

17 RE (520/521 Series) Hydraulic Motor With Medium Duty earing ordering information CHOOSE SERIES DESIGNTION. SELECT SHFT OPTION 520 Counterclockwise Rotation 521 Clockwise Rotation Spline 1-1/ Straight 32mm Straight Tooth Spline 1 Straight 1-1/ Tapered 5. SELECT PINT OPTION The 520 & 521 series are bi-directional. Reversing the inlet hose will reverse shaft rotation. For applications requiring the motor to rotate in only one direction, shaft seal life may be prolonged by pressurizing the port of the motor. 2. SELECT DISPLCEMENT OPTION 121 cm 3 /rev [7. in 3 /rev] 162 cm 3 /rev [. in 3 /rev] 20 cm 3 /rev [12. in 3 /rev] 232 cm 3 /rev [1.2 in 3 /rev] 261 cm 3 /rev [15. in 3 /rev] cm 3 /rev [18.3 in 3 /rev] SELECT MOUNT & PORT OPTION W31 W38 6-Hole, SE Mount, ligned Ports, 7/8-1 UNF 38 cm 3 /rev [21.2 in 3 /rev] cm 3 /rev [22.8 in 3 /rev] 65 cm 3 /rev [28.3 in 3 /rev] 536 cm 3 /rev [32.7 in 3 /rev] 78 cm 3 /rev [5.6 in 3 /rev] 6-Hole, SE Mount, ligned Manifold Ports, 1/2 Drilled 6-Hole, SE Mount, ligned Ports, G 1/2 -Hole, Wheel Mount, ligned Ports, 7/8/1 UNF -Hole, Wheel Mount, ligned Ports, G 1/2 lack lack, Unpainted Mounting Surface Z No Paint 6. SELECT VLVE CVITY / CRTRIDGE OPTION None 7. SELECT N DD-ON OPTION Standard Lock Nut C Solid Hex Nut 8. SELECT MISCELLNEOUS OPTION None C Freeturning Rotor E Hydraulic Declutch With Freeturning Rotor DELIVERING THE POWER TO GET WORK DONE 17

18 RE (530/531 Series) Hydraulic Motor With Heavy Duty earing housings Dimensions shown are without paint. Paint thickness can be up to 0.13 [.005]. 6-HOLE, SE MOUNT, LIGNED PORTS 51 7/8-1 UNF 58 G 1/2 71 [2.80] 66 [2.61] [2.7] Min. 1 [.73] 3.0 [.] 2.8 [.110] 86 [3.0] OO 137 [5.38] 82.6 [3.250] 82.5 [3.27] 13.3 [.52] 13.1 [.51] Ø [.187] -HOLE, WHEEL MOUNT, LIGNED PORTS * T31 7/8-1 UNF T38 G 1/2 W31 7/8-1 UNF W38 G 1/ [.52] 13.1 [.51] 132 [5.21] 63 [2.7] Min. 5.3 [1.785] 5.1 [1.775] 26 [1.02] 53 [2.07] OO 6 [.25] 132 [5.21] 82.6 [3.250] 82.5 [3.27] [.] 126. [.5] 5 Ø 17.6 [5.812] Dimension OO is charted on page 1. *The W31 & W38 housings offer a higher side load capacity. Refer to the bearing curves listed on page DELIVERING THE POWER TO GET WORK DONE

19 RE (530/531 Series) Hydraulic Motor With Heavy Duty earing technical information llowable Shaft Load / earing curve The bearing curve represents allowable bearing loads based on ISO 281 bearing capacity for an L 10 life of 2,000 hours at 100 rpm. Radial loads for speeds other than 100 rpm may be calculated using the multiplication factor table on page 11. SE MOUNTS T31 & T38 WHEEL MOUNTS mm mm SHFT SHFT ERING ERING lb in dan lb in dan W31 & W38 WHEEL MOUNTS mm ERING SHFT lb in dan length & weight chart Dimension OO is the overall motor length from the rear of the motor to the mounting flange surface and are referenced on detailed housing drawings listed on page 18. OO # SE Mounts 187 [7.37] 187 [7.37] 11 [7.51] Wheel Mounts 156 [6.15] 156 [6.15] 15 [6.2] Weight kg [lb] 13.3 [2.] 13.3 [2.] 13.7 [30.2] 13 [7.61] 162 [6.38] 13.8 [30.] 16 [7.70] 165 [6.8] 1.1 [31.0] 1 [7.83] 168 [6.61] 1. [31.8] 213 [8.38] 182 [7.16] 15.5 [3.2] 205 [8.08] 17 [6.86] 15.0 [33.0] ll RE series motor weights can vary ± 0.5 kg [1 lb] depending on model configurations such as housing, shaft, endcover, options etc [8.38] 21 [8.62] 237 [.33] 182 [7.16] 188 [7.0] 206 [8.11] 15.5 [3.2] 16.1 [35.] 17.5 [38.5] DELIVERING THE POWER TO GET WORK DONE 1

20 RE (530/531 Series) Hydraulic Motor With Heavy Duty earing Shafts 27 35mm Straight /2 Straight PP PP 58 [2.28] 78 [3.08] 10.0 [.3] 10.0 [.32] 6 [.2] 5.5 [1.71] 5.0 [1.772].6 [.376].5 [.] 10[.3] 38. [1.530] 37.6 [1.80] 38.0 [1.31] 38.0 [1.38] 35.0 [1.37] 35.0 [1.378] 2. [1.671] 2.1 [1.657] 38.1 [1.] 38.0 [1.8] M8x1.25, Min. Depth 18 [.6] 0 [1.58] Wire Ring 3/8-16 UNC, Min. Depth 1 [.75] Torque: 1 Nm [10600 lb-in] Torque: 1 Nm [10600 lb-in] 28 35mm Tapered /2 Tapered PP PP 8.0 [.31] 8.0 [.313] 22 [.87] 3 [.12] 36 [1.2] 22. [.00] 22.6 [.80] 8.0 [.31] 8.0 [.313] 1 [.75] 5 [.20] [1.72] 31.8 [1.250] 30.5 [1.] 35.0 [1.378] 3.5 [1.358] 38.1 [1.500] 38.1 [1.] [.15] [.15] Ø5 [.20] 1:10 Taper Ø [.17] 1:8 Taper Torque: 1 Nm [10600 lb-in] slotted hex nut is standard on this shaft. Torque: 1 Nm [10600 lb-in] slotted hex nut is standard on this shaft. M 1-3/8 Tapered mounting / shaft length chart 8.0 [.31] 8.0 [.313] 21 [.83] 5 [.20] PP 1 [1.63] 31.8 [1.250] 30.5 [1.] Dimension PP is the overall distance from the motor mounting surface to the end of the shaft and is referenced on detailed shaft drawings above. PP # Mounts SE N/ N/ 87 [3.2] Wheel Mounts 10 [3.7] 105 [.1] 118 [.63] 35.1 [1.380] 3. [1.] Shaft lengths vary ± 0.8 mm [.030 in.] 31 M 8 [3.32] 83 [3.28] 115 [.53] 11 [.] [.15] Torque: 1 Nm [10600 lb-in] Ø [.17] 1:8 Taper slotted hex nut is standard on this shaft. 20 DELIVERING THE POWER TO GET WORK DONE

21 RE (530/531 Series) Hydraulic Motor With Heavy Duty earing ordering information CHOOSE SERIES DESIGNTION. SELECT SHFT OPTION 530 Counterclockwise Rotation 531 Clockwise Rotation mm Straight 35mm Tapered 1-1/2 Straight 31 M 1-1/2 Tapered 1-3/8 Tapered The 27 & 28 shafts are not available with SE mounts. The M shaft is only available with the T mount wheel motors. 5. SELECT PINT OPTION The 530 & 531 series are bi-directional. Reversing the inlet hose will reverse shaft rotation. For applications requiring the motor to rotate in only one direction, shaft seal life may be prolonged by pressurizing the port of the motor. 2. SELECT DISPLCEMENT OPTION Z lack lack, Unpainted Mounting Surface No Paint 121 cm 3 /rev [7. in 3 /rev] 162 cm 3 /rev [. in 3 /rev] 20 cm 3 /rev [12. in 3 /rev] 232 cm 3 /rev [1.2 in 3 /rev] 261 cm 3 /rev [15. in 3 /rev] cm 3 /rev [18.3 in 3 /rev] cm 3 /rev [21.2 in 3 /rev] cm 3 /rev [22.8 in 3 /rev] 65 cm 3 /rev [28.3 in 3 /rev] 536 cm 3 /rev [32.7 in 3 /rev] 78 cm 3 /rev [5.6 in 3 /rev] 3. SELECT MOUNT & PORT OPTION 51 6-Hole, SE Mount, ligned Ports, 7/8-1 UNF 58 6-Hole, SE Mount, ligned Ports, G 1/2 T31 -Hole, Wheel Mount, ligned Ports, 7/8/1 UNF T38 -Hole, Wheel Mount, ligned Ports, G 1/2 W31 -Hole, Wheel Mount, ligned Ports, 7/8/1 UNF W38 -Hole, Wheel Mount, ligned Ports, G 1/2 6. SELECT VLVE CVITY / CRTRIDGE OPTION None 7. SELECT N DD-ON OPTION Standard Lock Nut C Solid Hex Nut 8. SELECT MISCELLNEOUS OPTION None C Freeturning Rotor E Hydraulic Declutch With Freeturning Rotor DELIVERING THE POWER TO GET WORK DONE 21

22 RE (50/51 Series) Hydraulic Motor With Wheel Hub housings Dimensions shown are without paint. Paint thickness can be up to 0.13 [.005]. -HOLE, WHEEL HU MOUNT, LIGNED PORTS W31 7/8-1 UNF (6) 1/2-20 SE Mounting Studs, Ø152 [6.00] olt Circle 32 [1.25] 138 [5.] QQ 187 [7.37] [.8] 126. [.5] () 1/2-20 SE Mounting Studs, Ø18 [5.81] olt Circle 21 [.83] 26 [1.03] Dimension QQ is charted on page 23. Hub option details STNDRD HU [1.72] 117 [.62] LOCKING HU 56 [2.21] 117 [.62] 27 [1.08] 22 DELIVERING THE POWER TO GET WORK DONE

23 RE (50/51 Series) Hydraulic Motor With Wheel Hub technical information llowable Shaft Load / earing curve The bearing curve represents allowable bearing loads based on ISO 281 bearing capacity for an L 10 life of 2,000 hours at 100 rpm. Radial loads for speeds other than 100 rpm may be calculated using the multiplication factor table on page 11. WHEEL HU MOUNTS mm length & weight chart Dimension QQ is the overall motor length from the rear of the motor to the mounting flange surface and are referenced on detailed housing drawings listed on page 22. ll RE series motor weights can vary ± 0.5 kg [1 lb] depending on model configurations such as housing, shaft, endcover, options etc. QQ # Length 70 [2.77] 70 [2.77] 7 [2.0] 76 [2.] 7 [3.0] 82 [3.22] 6 [3.77] 88 [3.7] 6 [3.77] 102 [.01] [.72] Weight kg [lb] 22.3 [.1] 22.3 [.1] 22.6 [.] 22.7 [50.1] 23.0 [50.7] 23. [51.5] 2. [53.] 23. [52.7] 2. [53.] 25.0 [55.1] 26. [58.2] ERING 500 lb dan 2 in ordering information CHOOSE SERIES DESIGNTION. SELECT SHFT OPTION 50 Counterclockwise Rotation 51 Clockwise Rotation 61 6-olt Wheel Flange 5. SELECT PINT OPTION Z lack No Paint 6. SELECT VLVE CVITY / CRTRIDGE OPTION The 50 & 51 series are bi-directional. Reversing the inlet hose will reverse shaft rotation. For applications requiring the motor to rotate in only one direction, shaft seal life may be prolonged by pressurizing the port of the motor. 2. SELECT DISPLCEMENT OPTION 121 cm 3 /rev [7. in 3 /rev] 162 cm 3 /rev [. in 3 /rev] 20 cm 3 /rev [12. in 3 /rev] 232 cm 3 /rev [1.2 in 3 /rev] 261 cm 3 /rev [15. in 3 /rev] cm 3 /rev [18.3 in 3 /rev] cm 3 /rev [21.2 in 3 /rev] cm 3 /rev [22.8 in 3 /rev] 65 cm 3 /rev [28.3 in 3 /rev] 536 cm 3 /rev [32.7 in 3 /rev] 78 cm 3 /rev [5.6 in 3 /rev] None 7. SELECT N DD-ON OPTION Standard H Locking Hub 8. SELECT MISCELLNEOUS OPTION None C Freeturning Rotor E Hydraulic Declutch With Freeturning Rotor 3. SELECT MOUNT & PORT OPTION W31 -Hole, Wheel Hub Mount, ligned Ports, 7/8-1 UNF DELIVERING THE POWER TO GET WORK DONE 23

24 RE (510/511 Series) Hydraulic Motor With Integral Drum rake housings Dimensions shown are without paint. Paint thickness can be up to 0.13 [.005]. -HOLE, WHEEL RKE MOUNT, LIGNED PORTS X31 7/8-1 UNF X38 G 1/ [.52] 13.1 [.51] 132 [5.21] 63 [2.7] Min. 26 [1.02] 53 [2.07] RR 6 [.25] 132 [5.21] [.] 126. [.5] 5 Dimension RR is charted on page 25. Hub option details 5-OLT, WHEEL HU Ø 17.6 [5.812] 28 [1.10] 52 [2.05] Ø11 [.50] 157 [6.18] 171 [6.75] 7 [3.12] 187 [7.38] (5) 1/2-20 SE Mounting Studs 10 [.31] -OLT, WHEEL HU 28 [1.10] 52 [2.05] 102 [.00] 187 [7.38] 171 [6.75] 157 [6.18] 10 [.31] 2 DELIVERING THE POWER TO GET WORK DONE

25 RE (510/511 Series) Hydraulic Motor With Integral Drum rake technical information RKE lever position & pull Direction brake holding torque Cable Force 20 FORWRD REVERSE kg Position 1, Right Hand Position 1, Left Hand Position 2, Right Hand Position 2, Left Hand 500 lb-in lb 100 Nm Holding Torque llowable Shaft Load / earing curve The bearing curve represents allowable bearing loads based on ISO 281 bearing capacity for an L 10 life of 2,000 hours at 100 rpm. Radial loads for speeds other than 100 rpm may be calculated using the multiplication factor table on page 11. MOTOR RKE mm 0 length & weight chart Dimension RR is the overall motor length from the rear of the motor to the mounting flange surface and is referenced on detailed housing drawings listed on page /511 motor/brake weights can vary ± 0.5 kg [1 lb] depending on model configurations such as housing, shaft, endcover, options etc. RR # Length 156 [6.15] 156 [6.15] 15 [6.2] 162 [6.38] 165 [6.8] 168 [6.61] 182 [7.16] 17 [6.86] 182 [7.16] 188 [7.0] 206 [8.11] Weight kg [lb] 1. [2.] 1. [2.] 15.2 [3.7] 15.3 [3.] 15.6 [.5] 16.0 [5.3] 17.1 [7.7] 16.5 [6.5] 17.1 [7.7] 17.6 [.0] 1.0 [52.0] ERING lb in dan DELIVERING THE POWER TO GET WORK DONE 25

26 RE (510/511 Series) Hydraulic Motor With Integral Drum rake ordering information CHOOSE SERIES DESIGNTION. SELECT SHFT OPTION 510 Counterclockwise Rotation 511 Clockwise Rotation /2 Tapered 5. SELECT PINT OPTION Z lack No Paint 6. SELECT VLVE CVITY / CRTRIDGE OPTION The 510 & 511 series are bi-directional. Reversing the inlet hose will reverse shaft rotation. For applications requiring the motor to rotate in only one direction, shaft seal life may be prolonged by pressurizing the port of the motor. 2. SELECT DISPLCEMENT OPTION 121 cm 3 /rev [7. in 3 /rev] 162 cm 3 /rev [. in 3 /rev] 20 cm 3 /rev [12. in 3 /rev] 232 cm 3 /rev [1.2 in 3 /rev] 261 cm 3 /rev [15. in 3 /rev] cm 3 /rev [18.3 in 3 /rev] SELECT MOUNT & PORT OPTION X31 X38 38 cm 3 /rev [21.2 in 3 /rev] cm 3 /rev [22.8 in 3 /rev] 65 cm 3 /rev [28.3 in 3 /rev] 536 cm 3 /rev [32.7 in 3 /rev] 78 cm 3 /rev [5.6 in 3 /rev] -Hole, Wheel rake Mount, ligned Ports, 7/8-1 UNF -Hole, Wheel rake Mount, ligned Ports, G 1/2 None 7. SELECT N DD-ON OPTION Standard 8. SELECT MISCELLNEOUS OPTION Y 5 olt Hub, Position 2, Right Hand Y 5 olt Hub, Position 2, Left Hand YE olt Hub, Position 2, Right Hand YF olt Hub, Position 2, Left Hand Z 5 olt Hub, Position 1, Left Hand Z 5 olt Hub, Position 1, Right Hand ZE olt Hub, Position 1, Left Hand ZF olt Hub, Position 1, Right Hand 26 DELIVERING THE POWER TO GET WORK DONE

27 North merica White Drive Products, Inc. P.O. ox 1127 Hopkinsville, KY. US 221 Phone: Fax: Europe White Drive Products GmbH Mannsnetterstrasse 3 D-8815 Opfenbach, Germany Phone: Fax: infoeu@.com sia White (China) Drive Products Co., Ltd. 1-8 Ning Zhen Gong Lu Zhenjiang, 221, Jiangsu, China Phone: Fax: infochina@.com Delivering The Power To Get Work Done! RE Catalog