SPECIFICATION FOR APPROVAL

Transcription

1 SPEIFITION FOR PPROVL Ⅰ. onfiguration and dimensions: 'S W NO. S0704 F - REV PE 1 1R0 E F (P Pattern) Unit:m/m 7.30 ± ± ± typ. E 4.60 typ. F 4.80 ref ref. 1. ref. Ⅱ. escription: a. Ferrite drum core construction. b. Magnetically shielded. c. Enamelled copper wire: class d. Product weight: 0.880g(ref.) e. Moisture sensitivity Level 1 f. Products comply with RoS' requirements g. alogen free available 2 Temperature Rising rea +4.0 / sec max. Preheat rea 1 ~ 200 / 60 ~ 120sec Peak Temp:2 max. Max. Peak Temp - 5 :30sec max. Max time above 217 :60sec~1sec max. Reflow rea +3.0 / sec max. Forced ooling rea -(1.0 ~ 5.0) / sec max. Peak Temperature: Ⅲ. eneral specification: a. Storage temp.: b. Operating temp.: ( Temp. rise included. ) c. Ressistance to solder heat:2. 10 secs. Temperature ( ) sec~120sec Time ( seconds ) 60sec max. 60sec~1sec 200 2

2 SPEIFITION FOR PPROVL Ⅳ. Electrical characteristics: 'S W NO. S0704 F - REV PE 2 W No. Inductance Test Freq. R (Ω) Irms Isat (u) (z) / 1V max. () () S07041R0MF - 1.0±20% S07042R2MF - 2.2±20% S07043R3MF - S07044R7MF - 3.3±20% 4.7±20% S07045R6MF - 5.6±20% S07046R8MF - 6.8±20% S MF - 1±20% S MF - S07041MF - S MF ±20% 15.0±20% 18.0±20% S MF ±20% S MF - S MF ±20% 33.0±20% S MF - S MF ±20% 47.0±20% S MF - S MF ±20% 68.0±20% S MF - S MF ±20% 10±20% S MF - S MF - 12±20% 15±20% S MF - 18±20% S MF - 22±20% S MF - S MF - S MF - S MF - S MF - S MF - 27±20% 33±20% 39±20% 47±20% 56±20% 68±20% S MF - 82±20% S MF - 100±20% ). :Packaging information: ode 2)."- ":Reference code 3). Electrical specifications at 25 4). L Test Freq.:z / 1V 5). Irms base on Temp. rise 40 max. 6). Isat base on L/L0=25% max.

3 SPEIFITION FOR PPROVL REF. : Ⅴ. urve: S ML 'S W NO. S0704 F - REV PE S ML S ML S ML

4 SPEIFITION FOR PPROVL Ⅵ. Packaging information: ( 1 ) onfiguration T 'S W NO. S0704 F - REV PE 4 2.0±0.5 over Tape N Embossed arrier arrier Tape Width : End P:12 m/m 4 m/m Start 1R0 1R0 1R0 1R0 Leader Trailer no component 200 m/m min. omponents no component 400 m/m min. User direction of feed ( 2 ) imensions Unit:m/m Style N T ±0.8 13± ( 3 ) Q'TY &.W. Per package ode Q'TY (pcs) Inner : Reel.W. (gw) Style Q'TY (pcs) Outer : arton.w. (Kg) Size (cm) 1, , x 37 x 22

5 SPEIFITION FOR PPROVL Ⅶ. Reliability test: 1.igh Temperature Exposure 2.Temperature ycling 3.iased umidity Test 4.Operational Life 5.Exeternal Visual 6.Physical imensions 7.Resistance to solvents 8.Vibration Test 9.Resistance To Soldering eat Test 10.Rated current 11.Temperature rise 12.Over load 13.Solderability Test 14.Electrical haracteriazation 15.Withstanding Voltage Test 16.rop 17.Terminal Strength Test Item Reference documents MIL-ST-202 Method 108 JES22 Method J-104 MIL-ST-202 Method 103 MIL-ST-202 Method 330 J-ST-002 User Spec. MIL-ST-202 Method 201 JES JIS Temperature: 85±5 2.Time:96 ours 3.umidity: 85±5% R. 1.Temperature: Time:96 hours. 3.pply rated current. Inspect product MIL-ST-883 Method 2009 constructions, marking and workmanship. JES22 Method J-100 MIL-ST-202 Method 215 MIL-ST-202 Method 204 MIL-ST-202 Method Temperature: Time:96 hours. Verify physical dimensions to the applicable product detail specification. Immerse into solvent for 3±0.5 minutes & brush 10 times for therr cycles. 1.Frequency and mplitued : z, 1.5 mm. 2.irection:X, Y, Z 3.Test duration:2 hours for each direction, 6 hours in total. 1.ighest temperature: 2±5 2.Time(temp. 217 ):60~1 Second. 3.IR reflow times:3 times. pply rated current for 5 second. pply rated current for 10 minutes. pply twice as rated current for 5 minutes. (It's not application to some special design) 1.aking in pre-testing: 155±5 / 16ours±30 min. 2.Peak temperature:240±5 3.Time(temp. 217 ):60~1 second. 4.IR reflow times:1 times. 1.Operating temperature: -40 ~125 2.Room temperature:25. 1.V:0V 2.Time:1minutes 'S W NO. REV. Test ondition 1.Temperature: -40 ~ Number of cycle:96 cycle 3.well time:30 minutes Packaged & rop down from 1m.In 1 angle 1ridges & 2 surfaces orientation. 1.pply push force to samples mounted on P. 2.Force of 1.8 kg for 60±1 seconds S0704 F - PE Test Specification 1.No pollution on the surface of products. 2.lear marking. 3.No crack. Per product specification standard 1.No body change in apperarance. 2.No marking blurred. 3.Inductance shall not change The terminal shall be at least 95% covered with fresh solder. 1.uring the test no breakdown. 2.The characteristic is normal after test. 1.No case deformation or change in appearance. fter test, inductors shall be no mechanical 5