Series 80 Mighty Mouse Technical Reference Complete Product Specification

Transcription

1 80 Mighty Mouse Technical Reference Reference SRIPTION RQUIRMNT PROUR TRI ontact resistance S S39029 Table V Max Wire Test Voltage Size urrent rop I I Test current in amperes. Voltage drop in millivolts. Silver-coated copper wire, +25. ow level contact resistance Wire Max. Size Milliohms I milliamperes maximum and 20 millivolts maximum open circuit voltage Insulation resistance 5000 megohms minimum I I volts ± 50 volts. Test between adjacent contacts and contacts to shell. ielectric withstanding voltage, sea level ielectric withstanding voltage, 70,000 feet altitude No breakdown or flashover #23 contacts 500 volts #20 contacts 750 volts #16 contacts 1800 volts #12 contacts 1800 volts No breakdown or flashover #23 contacts 100 volts #20 contacts 150 volts #16 contacts 1000 volts #12 contacts 1000 volts I I rms 60 z. One minute dwell. Unmated or mated I I rms 60 z. One minute dwell. mated condition urrent carrying capacity ontact Max Size urrent I Method 1 I Test 9b M imensions in inches (millimeters) and are subject to change without notice. NIR, IN IR WY N, X Mail: sales@glenair.com

2 Reference 80 Mighty Mouse Technical Reference SRIPTION RQUIRMNT PROUR Shell-to-shell conductivity, Initial The maximum voltage drop across a mated pair shall not exceed the values shown. Voltage rop I I lectroless nickel plated connectors. Shell-to-shell conductivity, after conditioning (48 hours salt spray) The maximum voltage drop across a mated pair shall not exceed the values shown. Voltage rop I I lectroless nickel plated connectors. Shielding effectiveness, low frequency (100Mz-1000 Mz) requency d Min. ttenuation 800, 801, 802, 804, Mz Mz Mz Mz Mz Mz MI-T para lectroless nickel plated connectors Shielding effectiveness, high frequency (1hz- 10z) requency d Min. ttenuation 800, 801, 802, z z z z I I lectroless nickel plated connectors imensions in inches (millimeters) and are subject to change without notice. NIR, IN IR WY N, X Mail: sales@glenair.com

3 80 Mighty Mouse Technical Reference Reference SRIPTION RQUIRMNT PROUR MNI Vibration, sine microseconds, no cracking, breaking or disengaged from receptacle. onnectors vibration test. MI-ST-202 Method 204, test ondition 30 g s, 3 axes, 4 hours per axis Vibration, random unfire vibration microseconds, no cracking, breaking or disengaged from receptacle. onnectors vibration test. microseconds, no cracking, breaking or disengaged from receptacle. onnectors vibration test. I Test ondition V etter I I milliamp test current 50-2,000 z g rms MI-ST-810 Method Mechanical shock microsecond, no cracking, breaking or disengaged from receptacle. onnectors shock test. I ondition I shocks X 3 axes X 2 directions = 18 shocks 2941 m/s 2 (300 g s), 3 ms, halfsine Mechanical durability, at ambient temperature No deterioration which will adversely affect the connector after 2000 cycles of mating and unmating. onnectors shall meet contact resistance, insulation resistance, shell-to-shell resistance, WV, and mating and unmating force. I I Test 9a Solderability, P tail contacts 95% solder coverage. Smooth, bright and even finish. I ategory 3 I I Test Ta, method 1 8 hours steam aging prior to test 245, 4-5 sec. dwell 10X magnification Resistance To Soldering eat No damage to connector. onnectors shall meet insulation resistance and waterproof sealing requirements. I I Test 12e 260, 10 seconds (P tail) M imensions in inches (millimeters) and are subject to change without notice. NIR, IN IR WY N, X Mail: sales@glenair.com

4 Reference 80 Mighty Mouse Technical Reference SRIPTION RQUIRMNT PROUR Impact No impairment of function. onnector shall meet contact resistance, insulation resistance and waterproof sealing. I I test 7b 1 meter 8 drops ontact retention ontact Min. Min. Size Pounds Newtons I ontact separation force ontact Min. Min. Size Ounces Newtons S S39029 oupling torque Threaded coupling connector coupling torque shall not exceed the following requirements. 800, 801 Shell Size 805 Inch Pound 5, 6, 7 8, 9 8 8,9 10, , , 15, , quick-disconnect connectors Unmating force ( 804) ontact rrangement Inch Pound imensions in inches (millimeters) and are subject to change without notice. NIR, IN IR WY N, X Mail: sales@glenair.com

5 80 Mighty Mouse Technical Reference Reference SRIPTION RQUIRMNT PROUR Unmated connectors shall retain their inserts in their proper location in the shell and there shall be no evidence of cracking, breaking, separation from the shell, or loosening of parts. Insert retention Ser. 800, Shell Size Min. orce in Pounds 5 Ser Ser I Residual magnetism 2 μ maximum. I Operating temperature -65 to +150 NVIRONMNT Water immersion, mated No evidence of water penetration into mated connectors. 100 MΩ insulation resistance. MI-ST-810 Method meter immersion 1 hour Water immersion, open face panel mount receptacles with non-removable printed circuit board or solder cup contacts onnectors with waterblock potting process (lenair Modification ode 518 required). 1 X 10-4 cc/second maximum helium leak rate at 1 atmosphere pressure differential following thermal shock conditioning. I cycles thermal shock -57 to min. dwell 5 minute transfer rate umidity, cyclic (damp heat, cyclic) (moisture resistance) No deterioration which will adversely affect the connector. 100 megohms minimum insulation resistance during the final cycle. ollowing the recovery period, connectors shall meet contact resistance, shell-to-shell resistance and WV requirements. I ondition Method III I % R 10 cycles (10 days) +25 to +65 Step 7b vibration deleted. 24 hour recovery period. M imensions in inches (millimeters) and are subject to change without notice. NIR, IN IR WY N, X Mail: sales@glenair.com

6 Reference 80 Mighty Mouse Technical Reference SRIPTION RQUIRMNT PROUR 21 day humidity (damp heat, long term) Thermal shock No deterioration which will adversely affect the connector. ollowing the drying period, connectors shall meet 100 megohms minimum, contact resistance, shell-to-shell resistance, WV, mating and unmating requirements. No mechanical damage or loosening of parts. ollowing thermal shock, connector shall meet contact resistance, WV, insulation resistance and shell-to-shell resistance requirements. I ondition Method II I Severity 90-95% R 40 pply 100 volts during test. 4 hours drying time at ambient temperature prior to final measurements. I Test ondition IV I cycles consisting of minutes, minutes max., minutes, minutes max. orrosion (salt mist) No exposure of base metal. onnectors shall meet WV and contact resistance requirements following the test. I I % salt solution 35 Unmated connectors ode : 48 hours ode M: 48hours ode MT: 500 hours ode N: 500 hours ode ZN: 500 hours ode ZNU: 500 hours ode UR: 500 hours Sand and dust Mated connectors shall withstand the effects of blowing sand and dust MI-ST-810, Method ungus onnector materials shall be fungus inert. MI-ST-810, Method luid immersion No visible damage from immersion in various fuels and oils. onnector shall meet coupling torque and dielectric withstanding voltage requirements. I Unmated connectors ltitude immersion No evidence of moisture on connector interface or contacts. onnector shall meet dielectric withstanding voltage. I Wired crimp connectors with supplemental potting. Printed circuit board and solder cup connectors with standard factory-installed potting. Outgassing The entire connector assembly shall be capable of meeting a maximum Total Mass oss (TM) of 1% and a Total ollected Volatile Material oss (TVM) of 0.1% following additional processing for outgassing control. STM-595 imensions in inches (millimeters) and are subject to change without notice. NIR, IN IR WY N, X Mail: sales@glenair.com