MOBILE OIL COOLERS ELEMENTS

Transcription

1 ntroduction RS TS 2000K SRS STR S T-RS 2000KV SRS WT UT- TR YPSS KVV

2 Performance R PRR T RJT orsepower@50 T P = 5 PS = 10 PS = 25 PS = 50 PS 50 SUS 2010K 2005K 2015K KS KSV 2050K 2050KV 2040K 2040KV 2030K 2030KV 2024K 2024KV 2020K 2020KV 2015KV W - P R STT PRSSUR RP T R P - S WTR K 2020KV 2024K 2024KV 2030K 2030KV 2040K 2040KV KS 2050K 2050KV KSV 2005K 2010K 2015K 2015KV VTY - SP R VTY RRT TR ( ) SP PRSSUR RP RRT TR ( ) SUS

3 ntroduction air/oil Series oil coolers are designed to mount in front the engine radiator or other fan (or air flow) provided by the customer. The all aluminum ar and Plate construction is very robust and resistant to external damage. With reasonable care, the coolers may be pressure washed to remove external debris. turbulators greatly enhance performance providing the maximum heat transfer in a very compact size. omponents are vacuum brazed leaving the internal passages free contamination. ompatible fluids ineral ils: & P. Water - il mulsion. Water - lycol. onsult actory for other fluids. nstallation Series coolers should be installed as close as possible to the radiator to ensure the air flow does not bypass the cooler. nsure proper pipe size to reduce restriction. (ack pressure) o not exceed either the maximum rated flow or pressure. Serious damage or failure could result, and are not covered by warranty. Use caution while fitting pipes to avoid putting excessive strain on pipes, connections, or the heat exchanger. or best heat dissipation it is suggested that the oil inlet be to the lower connection, but is not required. or low oil flow piping to the lower connection will purge air assuring maximum performance. s with a factory installed bypass UST be piped correctly to function properly. The inlet for the 2000KV and PV models is on the same manifold as the bypass valves. aintenance il side cleaning (internal): ll internal surfaces are aluminum. ny commercial cleaner may be used providing it is suitable for use on aluminum surfaces. ften this cleaning agent can be used on the external surfaces as well. ounter flushing the internal passages is the most effective cleaning method. fter cleaning the cooler should be flushed with the fluid used in the application to remove/prevent contamination. odel odes odel Size/Series K = o ypass KV = With ypass P : 2024KV--J - 22 ooler nly ode = ooler nly ir side cleaning (external): This can be done with either compressed air or water. f a pressure washer is used, keep the jet water parallel to the fins to avoid any damage. The use steam or hot water is helpful if the accumulation oily dirt is present. Selection Procedures The performance curves are based on the following: 1000 Standard eet Per inute ( SP) ir Velocity. 50 ntering Temperature ifference (T) T= ntering Temperature - ntering R Temperature 50 SUS il f your application conditions are different, use the following selection procedure: STP 1. etermine the eat oad orsepower eat = P STP 2. etermine the ctual T esired ntering il Temperature - ntering ir Temperature= T STP 3. ind the ir Velocity orrection actor S ir low cross ooler = SP R VTY T² ooler ace rea nce you have calculated the SP Velocity enter the air velocity correction curve to determine the correction factor. STP 4. alculate the djusted P for Selection P 50 P eat esired ir Velocity = or Use oad T orrection With actor Selection hart STP 5. Select The odel rom The urves Read up from the P to the required heat rejection. Select and model on, or above this point. Technical Specifications. aterial: long life aluminium.. perating pressure: 280 PS. Test pressure: 500 PS. ax operating temperature: or specially aggressive atmospheres contact. Port / daptor Type P= SPP Thread J = J Thread J90 = 90 J ypass Pressure Setting 2000K Series lank = o ypass 2000KV Series 22 = 22 psi ( 1.5 ar ) 44 = 44 psi ( 3 ar ) 3

4 imensions J SPP.8 Ø 0.35 x K 2020K 2024K 2030K 2040K easure ver-all dimensions and technical characteristic are not binding SPP J J 90 SPP J , # 16 # 20 1/2 SPP 1/2 SPP 1/2 SPP 1/2 SPP 1/2 SPP ace area et weight J SPP reather Ø 1/4"SPP Ø 1/2"SPP.8 Ø 0.35 x0.59 easure SPP J J 90 ver-all dimensions and technical characteristic are not binding 2050K SPP J 1.25 # 20 ace area et weight

5 imensions J SPP Ø1/4"SPP.8 Ø 0.35 x0.59 Ø 1/2"SPP easure SPP J J 90 ver-all dimensions and technical characteristic are not binding KS SPP J 1.50 # 24 ace area et weight J SPP y pass 43 psi (VR1302).4 eli coil Ø 1/2"SPP.4 Ø 0.35 x KV 2020 KV 2024 KV 2030 KV 2040 KV easure SPP J J 90 ver-all dimensions and technical characteristic are not binding , SPP J 1 # 16 ace area et weight

6 imensions J SPP reather Ø 1/4"SPP.4 eli coil 6 Valve y-pass 43 psi (VR1302).4 Ø 0.35 x Ø 1/2"SPP 2050 KV ver-all dimensions and technical characteristic are not binding ace area et weight reather ø1/4"spp.4 eli coil 6 Valve y-pass 43 psi (VR1302).4 Ø0.35"x0.59" easure SPP J J 90 SPP J 1.25 # J SPP Ø 1/2"SPP KSV easure SPP J J 90 ver-all dimensions and technical characteristic are not binding SPP J 1.50 # 24 ace area et weight

7 Sales etwork US T RS nc. (ain ffice and anufacturing) Southern ve. Suite 2 Phoenix, Z US Ph ax sales@emmegiinc.com emmegiinc.com SVK T RS s.r.o. U..Razusa Topolcany Ph ax sro@emmegi-heat-exchangers.com SW / T RS R. ox Visitors: ybrovagen 4 Ph (0) ax + 46 (0) info.nordic@emmegi-heat-exchangers.com S / P T RS td 17.9/.orporation Park, 11 n ai Street, Siu ek Yuen, Shatin, ong Kong Ph ax emmegi@biznetvigator.com RY mb Philipp-Reis-Straße revenbroich-kapellen vertrieb@emmegi-gmbh.de Sales ffice -37, Shed khla ndustrial rea, Phase W varun@emmegi-heat-exchangers.com T RS (eijing) o.,td. 706,7/. uilding, hina oreign anguage ansion, 89 West, 3 rd Ring () Road, aidian istrict,eijing, PR.hina,Post code: Ph ax emmegi@vip.sina.com UK UK (Sales ffice) vergreen, The Reddings heltenham 51 6R Ph ax sales@emmegi.co.uk eadquarters T S.p.. Via ewton,52 - Zona ndustriale assano d dda () - taly Tel ax info@emmegi-heat-exchangers.com