Husky 3300 Air-Operated Diaphragm Pump

Transcription

1 / aximiliano Thous, , Valencia (spaña) Operation usky 3300 ir-operated iaphragm Pump N eavy-duty 3-inch pump with large flow paths for fluid transfer applications, including high-viscosity materials. or professional use only. See page 4 for model information, including approvals. 125 psi (0.86 Pa, 8.6 bar) aximum Working Pressure, luminum or Stainless Steel Pumps with luminum enter Section 100 psi (0.7 Pa, 6.9 bar) aximum Working Pressure, Polypropylene or Stainless Steel Pumps with Polypropylene enter Section Important Safety Instructions Read all warnings and instructions in this manual. Save these instructions. Polypropylene luminum Stainless Steel TI17454a TI16556a TI16561a

2 / aximiliano Thous, , Valencia (spaña) onfiguration Number atrix onfiguration Number atrix heck the identification plate (I) for the 20-digit onfiguration Number of your pump. Use the following matrix to define the components of your pump. Sample onfiguration Number: TPTPN TP TP N Pump odel enter luid Section and overs and ir Valve anifolds Seats alls iaphragms anifold and Seat Seals Pump onfiguration Number ti17770a Pump 3300 luminum 3300P Polypropylene 3300S enter Section and ir Valve aterial or Use With luid overs and anifolds luminum 01 Standard iaphragms 1 luminum, center flange, npt 01 Optional seals with 2 luminum, center flange, bspt Standard iaphragms 01 Overmolded iaphragms P1 Polypropylene, center flange Polypropylene P01 Standard iaphragms S1 Stainless steel, npt P01 Overmolded iaphragms S2 Stainless steel, bspt Stainless Steel 3300 (aluminum) and 3300S (stainless steel) pumps with aluminum center sections are certified: II 2 c II T4 Pumps with polypropylene fluid or center sections are not TX certified. heck Valve Seats heck Valve alls iaphragm anifold and Seat Seals* cetal cetal N una-n N una-n luminum N una-n O Polychloroprene Overmolded N una-n R Polychloroprene Standard luoroelastomer W Polychloroprene Weighted R Polychloroprene eolast luoroelastomer eolast luoroelastomer PP Polypropylene eolast PO PT/P Overmolded SP Santoprene PT PT PT PT/Santoprene Two-Piece SS 316 Stainless Steel SP Santoprene SP Santoprene TP TP TP TP TP TP * odels with una-n, luoroelastomer or TP seats do not use o-rings. PT PT

3 / aximiliano Thous, , Valencia (spaña) luminum Pump imensions luminum Pump imensions ir Inlet (opposite side from muffler) ti16558a ti16557a ti16559a in. (62.2 cm) in. (72.7 cm) 4.13 in. (10.5 cm) in. (82.7 cm) in. (30.6 cm) in. (61.2 cm) in. (50.0 cm) 8.25 in. (21.0 cm) 18.8 in. (47.8 cm) in. (42.1 cm) in. (33.0 cm) 16.5 in. (41.9 cm)

4 / aximiliano Thous, , Valencia (spaña) Polypropylene Pump imensions Polypropylene Pump imensions ir Inlet (opposite side from muffler) ti16563a ti16562a ti16564a in. (93.5 cm) in. (105.2 cm) in. (115.2 cm) 4.60 in. (11.7 cm) in. (37.0 cm) in. (74.0 cm) in. (67.8 cm) 8.30 in. (21.1 cm) in. (47.9 cm) in. (49.0 cm) in. (33.0 cm) in. (42.1 cm)

5 / aximiliano Thous, , Valencia (spaña) Stainless Steel Pump imensions Stainless Steel Pump imensions ir Inlet (opposite side from muffler) ti17456a ti17455a ti17457a 23.8 in. (60.5 cm) in. (70.8 cm) 30.5 in. (77.5 cm) 4.5 in. (11.4 cm) in. (31.3 cm) in. (62.7 cm) in. (49.2 cm) 8.25 in. (21.0 cm) in. (48.4 cm) in. (42.7 cm) 13.0 in. (33.0 cm) 16.5 in. (41.9 cm)

6 / aximiliano Thous, , Valencia (spaña) Performance harts Performance harts Test onditions: Pump tested in water with inlet submerged. 125 (0.86, 8.6) pprox. ycles per inute luid Pressure Operating ir Pressure 125 psi (0.83 Pa, 8.3 bar) 100 psi (0.7 Pa, 7.0 bar) 70 psi (0.48 Pa, 4.8 bar) 40 psi (0.28 Pa, 2.8 bar) luid Pressure - psi (Pa, bar) 100 (0.69, 7.0) 75 (0.52, 5.2) 50 (0.34, 3.4) 25 (0.17, 1.7) (189) (379) (568) (757) luid low gpm (lpm) 250 (946) 300 (1136) ow to Read the harts 1. ocate fluid flow rate along bottom of chart. 2. ollow vertical line up to intersection with selected operating air pressure curve. 3. ollow left to scale to read fluid outlet pressure (top chart) or air consumption (bottom chart). ir onsumption - scfm (cubic meters/min.) 375 (10.6) 300 (8.5) 225 (6.4) 150 (4.2) 75 (2.1) pprox. ycles per inute ir onsumption (189) 100 (379) 150 (568) 200 (757) 250 (946) 300 (1136) luid low gpm (lpm)

7 / aximiliano Thous, , Valencia (spaña) Technical ata Technical ata usky 3300 US etric aximum fluid working pressure luminum or Stainless Steel with 125 psi 0.86 Pa, 8.6 bar luminum enter Section Polypropylene or Stainless Steel with 100 psi 0.7 Pa, 7 bar Polypropylene enter Section ir pressure operating range** luminum or Stainless Steel with psi Pa, bar luminum enter Section Polypropylene or Stainless Steel with psi Pa, bar Polypropylene enter Section ir consumption ll pumps 90 scfm at 70 psi, 100 gpm 2.5 m 3 /min at 4.8 bar, 379 lpm aximum air consumption* luminum or Stainless Steel with 335 scfm luminum enter Section 9.5 m 3 /min Polypropylene or Stainless Steel with 275 scfm Polypropylene enter Section 7.8 m 3 /min aximum free-flow delivery* Standard diaphragms 300 gpm at 125 psi 1135 lpm at 8.6 bar Standard diaphragms 280 gpm at 100 psi 1059 lpm at 7 bar Overmolded diaphragms 270 gpm at 125 psi 1022 lpm at 8.6 bar Overmolded diaphragms 260 gpm at 100 psi 984 lpm at 7 bar aximum Pump Speed* Standard diaphragms 103 cpm at 125 psi 103 cpm at 8.6 bar Standard diaphragms 97 cpm at 100 psi 97 cpm at 7 bar Overmolded diaphragms 135 cpm at 125 psi 135 cpm at 8.6 bar Overmolded diaphragms 130 cpm at 100 psi 130 cpm at 7 bar aximum suction lift (varies widely based on ball/seat selection and wear, operating speed, material properties, and other variables)* ry 8 ft. 2.4 meters Wet 28 ft. 8.5 meters Recommended cycle rate for continuous duty cpm Recommended cycle rate for circulation systems 20 cpm aximum size pumpable solids 1/2 in. 13 mm luid flow per cycle** Standard diaphragms 2.9 gal 11.0 l Overmolded diaphragms 2.0 gal 7.6 l Noise (da)*** Sound Power Sound Pressure 92 at 50 psi and 50 cpm, 99 at 120 psi and full flow 86 at 50 psi and 50 cpm 93 at 120 psi and full flow 92 at 3.4 bar and 50 cpm 99 at 8.3 bar and full flow 86 at 3.4 bar and 50 cpm 93 at 8.3 bar and full flow

8 / aximiliano Thous, , Valencia (spaña) Technical ata Inlet/Outlet Sizes luid inlet - Polypropylene luid inlet - luminum luid inlet - Stainless Steel ir Inlet - all pumps Wetted parts ll pumps Non-wetted external parts Polypropylene luminum Stainless Steel 3 in. NSI/IN flange 3 in.-8 npt or 3 in.-11 bspt with 3 in. NSI/IN flange 3 in.-8 npt or 3 in.-11 bspt 3/4 in. npt(f) aterials chosen for seat, ball, and diaphragm options, plus the pump s material of construction - aluminum, polypropylene, or stainless steel. luminum pumps also have carbon-coated steel. stainless steel, polypropylene aluminum, coated carbon steel stainless steel, polypropylene or aluminum (as used in center section) Weight Polypropylene 200 lb 91 kg luminum 150 lb 68 kg Stainless Steel 255 lb 116 kg Notes * aximum values with water as media at ambient temperature. Water level is approximately 3 feet above pump inlet. ** Startup pressures and displacement per cycle may vary based on suction condition, discharge head, air pressure, and fluid type. *** Sound power measured per ISO Sound pressure was tested 3.28 ft (1 m) from equipment. Santoprene is a registered trademark of the onsanto o. octite is a registered trademark of the octite orporation

9 / aximiliano Thous, , Valencia (spaña) Technical ata luid Temperature Range NOTI Temperature limits are based on mechanical stress only. ertain chemicals will further limit the fluid temperature range. Stay within the temperature range of the most-restricted wetted component. Operating at a fluid temperature that is too high or too low for the components of your pump may cause equipment damage. iaphragm/all/seat aterial luid Temperature Range luminum Pumps Polypropylene Pumps cetal 10 to to to to 66 una-n 10 to to to to 66 luoroelastomer* -40 to to to to 66 eolast -40 to to to to 66 Polychloroprene overmolded diaphragm 0 to to to to 66 or Polychloroprene check balls Polypropylene 32 to to to to 66 PT overmolded diaphragm 40 to to to to 66 PT check balls 40 to to to to 66 Santoprene or two-piece PT/Santoprene -40 to to to to 66 diaphragm TP -20 to to to to 66 * The maximum temperature listed is based on the TX standard for T4 temperature classification. If you are operating in a non-explosive environment, fluoroelastomer s maximum fluid temperature in aluminum pumps is 320 (160 )