Process Equipment Catalog Pumping Solutions for Process Industries

Transcription

1 Process Equipment atalog Pumping Solutions for Process Industries

2

3 Table of ontents Process Equipment uyer s Guide ontents New Products... 2 Pump Model Overviews... 3 Pump Selection Key for ODD Pumps... 8 hemsafe hemsafe hemsafe hemsafe hemsafe Husky 205 Plastic Pumps Husky 307 Plastic Pumps Husky 515 Plastic Pumps Husky 716 Metal Pumps Husky 1050 Plastic Pumps Husky 1050 Metal Pumps Husky 1050HP Metal Pumps Husky 1590 Plastic Pumps Husky 1590 Metal Pumps Husky Plastic Pumps Husky 2150 Plastic Pumps Husky 2150 Metal Pumps Husky 2200 Plastic Pumps Husky 3300 Plastic Pumps Husky 3300 Metal Pumps Husky Transfer Pump Packages Husky Pump ccessories ycleflo and ycleflo II Surge Suppressors Husky 1050e SoloTech Hose Pumps Hydra-lean Fast-Flo 1: Piston Pumps for Ink pplications Notes

4 New Products hemsafe ir-operated Double Diaphragm Pumps hemsafe pumps feature PTFE or UHMWPE corrosion-resistant fluid paths, which make them ideal for corrosive and abrasive chemicals. Plus they re dead-head capable and can achieve high flow rates while minimizing air consumption and operational noise. See pages for more information. Husky 1050e Electric Double Diaphragm Pumps Our Husky e-series pumps are ideal for applications that require low pulsation and a smooth flow and they re up to 5x more efficient than ODD pumps. The patented air charged drive allows for the reduction of pulsation WITHOUT expensive pulsation dampeners or surge tanks. See pages for more information. SoloTech Peristaltic Hose Pumps SoloTech hose pumps are designed to utilize a single oversized roller that compresses a low friction hose through a full 360 degrees of rotation. This innovative design means longer hose life when pumping caustic, abrasive or sensitive materials for metering or transfer. See pages for more information. 2

5 Model Overview hemsafe ir-operated Double Diaphragm Pumps Model hemsafe 205 hemsafe 307 hemsafe 515 hemsafe 1040 hemsafe 1590 onnection Size 1/4 in (6.3 mm) 3/8 in (9.4 mm) 1/2 in (12.7 mm) 1 in (25.4 mm) 1.5 in (38.1 mm) Thread Type NPT or SPT NPT or SPT NPT or SPT NPT or SPT NPT or SPT ir Valve Standard Standard Standard Standard Standard Maximum Flow Rate 3.7 gpm (14 lpm) 6.7 gpm (25 lpm) 16 gpm (61 lpm) 39 gpm (156 lpm) 100 gpm (376 lpm) Maximum Discharge Pressure 100 psi (7 bar, 0.7 MPa) 100 psi (7 bar, 0.7 MPa) 100 psi (7 bar, 0.7 MPa) 100 psi (7 bar, 0.7 MPa) 100 psi (7 bar, 0.7 MPa) Materials of onstruction vailable enter Section vailable PTFE, UHMWPE PTFE, UHMWPE PTFE, UHMWPE PTFE, UHMWPE PTFE, UHMWPE Polypropylene Polypropylene Polypropylene Polypropylene Polypropylene Pump Weight 4.1 lb (1.9 kg) PTFE 6.8 lb (3.1 kg) PTFE 20 lb (9.1 kg) PTFE 40 lb (18 kg) PTFE 95.2 lb (43.2 kg) PTFE 4 lb (1.8 kg) UHMWPE 6 lb (2.7 kg) UHMWPE 13.7 lb (6.2 kg) UHMWPE 26.4 lb (12 kg) UHMWPE 66 lb (30 kg) UHMWPE Maximum Solids 0.06 in (1.5 mm) 0.08 in (2.0 mm) 0.16 in (4.1 mm) 0.24 in (6.1 mm) 0.32 in (8.1 mm) 3

6 Model Overview Husky Electric Double Diaphragm Pumps Model Husky 1050e Husky 1050e Husky 1050e Material of onstruction luminum Polypropylene Stainless Steel onnection Size 1 in (25.4 mm) 1 in (25.4 mm) 1 in (25.4 mm) Thread Type NPT or SPT NPT or SPT NPT or SPT Motor or LD or LD or LD Power 110V, 22V, or 480V Single or Three Phase 110V, 22V, or 480V Single or Three Phase 110V, 22V, or 480V Single or Three Phase Maximum Flow Rate 39 gpm (148 lpm) 39 gpm (148 lpm) 39 gpm (148 lpm) Maximum Discharge Pressure 70 psi (4.8 bar,.48 Mpa) 70 psi (4.8 bar,.48 Mpa) 70 psi (4.8 bar,.48 Mpa) enter Section vailable luminum luminum or Stainless Steel luminum or Stainless Steel Pump Weight Motor Models LD Motor Models 106 lb (48 kg) 90 lb (41 kg) lb (55 kg) lb (48 kg) lb (47 kg 87.5 lb (40 kg) Maximum Solids 1/8 in (3.2 mm) 1/8 in (3.2 mm) 1/8 in (3.2 mm) Operation manual

7 Model Overview SoloTech Hose Pumps Model SoloTech 10 SoloTech 23 SoloTech 26 SoloTech 30 Material of onstruction (Housing) luminum luminum luminum luminum Hose Material Natural Rubber, SM, Nitril, EPDM Natural Rubber, SM, Nitril, EPDM Natural Rubber, SM, Nitril, EPDM Natural Rubber, SM, Nitril, EPDM arb Material Stainless Steel, PVDF, Hastelloy Stainless Steel, PVDF, Hastelloy Stainless Steel, PVDF, Hastelloy Stainless Steel, PVDF, Hastelloy onnection Type and Size DIN PN /8 in, NSI 150 1/2 NPS, JIS 10K 10 DIN PN in, NSI /4 NPS, JIS 10K 025 DIN PN in, NSI /4 NPS, JIS 10K 025 DIN PN /4 in, NSI /2 NPS, JIS 10K 032 Motor or LD or LD or LD or LD Power 110V, 22V, or 480V Single or Three Phase 110V, 22V, or 480V Single or Three Phase 110V, 22V, or 480V Single or Three Phase 110V, 22V, or 480V Single or Three Phase Maximum Flow Rate* gpm (148 lpm) 4.75 gpm (17.98 lpm) gpm (38.54 lpm) 16.0 gpm (60.57 lpm) Minimum Flow Rate* Motor Models LD Motor Models 0.01 gpm (.038 lpm) gph (.01 lph) 0.1 gpm (.379 lpm) gph (.01 lph) 0.2 gpm (.757 lpm) gph (.01 lph) 0.4 gpm (1.51 lpm) gph (.01 lph) Maximum Discharge Pressure 125 psi (8.6 bar,.86 MPa) 125 psi (8.6 bar,.86 MPa) 125 psi (8.6 bar,.86 MPa) 125 psi (8.6 bar,.86 MPa) Pump Weight Motor Models LD Motor Models 65 lb (29 kg) 55 lb (25 kg) 120 lb (54 kg) 100 lb (45 kg) 215 lb (98 kg) 190 lb (86 kg) 285 lb (129 kg) 235 lb (107 kg) Maximum Solids.201 in (5 mm).672 in (17.1 mm).798 in (20.3 mm).965 in (24.5 mm) Operation Manual Repair Parts Manual

8 Model Overview Husky ir-operated Double Diaphragm Pumps Model Husky 205 Plastic Husky 307 Plastic Husky 515 Plastic Husky 716 Metal Husky 1050 Plastic Husky 1050 Metal Husky 1050HP onnection Size 1/4 in (6.3 mm) 3/8 in (9.4 mm) 1/2 in (12.7 mm) 3/4 in (19.1 mm) 1 in (25.4 mm) 1 in (25.4 mm) 1 in (25.4 mm) Thread Type NPT or SPT NPT or SPT NPT or SPT NPT or SPT NSI/DIN Flange NPT or SPT NPT or SPT ir Valve Standard and Remote Standard Standard and Remote Standard and Remote Standard, Smart and Remote Standard, Smart and Remote Standard Maximum Flow Rate 5 gpm (19 lpm) 7 gpm (26 lpm) 15 gpm (57 lpm) 16 gpm (61 lpm) 50 gpm (189 lpm) 50 gpm (189 lpm) 50 gpm (189 lpm) Maximum Discharge Pressure 100 psi (7 bar, 0.7 MPa) 100 psi (7 bar, 0.7 MPa) 100 psi (7 bar, 0.7 MPa) 100 psi (7 bar, 0.7 MPa) 125 psi (8.6 bar. 0.9 MPa) 125 psi (8.6 bar, 0.9 MPa) 250 psi (17.2 bar, 1.7 MPa) Materials of onstruction vailable enter Section vailable Polypropylene, PVDF, cetal Polypropylene, cetal Polypropylene, PVDF, cetal luminum, 316 SST Polypropylene, onductive Poly, PVDF Polypropylene Polypropylene Polypropylene Polypropylene Polypropylene, onductive Poly luminum, 316 SST, Hastelloy oated luminum, Polypropylene, onductive Poly luminum, 316 SST luminum Pump Weight 2.0 lb (0.9 kg) Polypropylene 4.75 lb (2.2 kg) Polypropylene 6.5 lb (2.9 kg) Polypropylene 8.5 lb (3.9 kg) luminum 18 lb (8.2 kg) Polypropylene 23 lb (10.4 kg) luminum 48 lb (21.8 kg) luminum 2.5 lb (1.1 kg) cetal 2.8 lb (1.3 kg) PVDF 5.2 lb (2.4 kg) cetal 7.8 lb (3.5 kg) cetal 8.5 lb (3.9 kg) PVDF 18 lb (8.2 kg) SST 26 lb (11.8 kg) PVDF lb ( kg) SST 41 lb (18.6 kg) Hastelloy 60 lb (27.2 kg) SST Maximum Solids 0.06 in (1.5 mm) in (1.6 mm) in (2.5 mm) in (2.5 mm) in (3.2 mm) in (3.2 mm) in (3.2 mm) Viscosity Up to 500 cps Up to 1,000 cps Up to 5,000 cps Up to 5,000 cps Up to 10,000 cps Up to 10,000 cps Up to 10,000 cps 6

9 Husky 1590 Plastic Husky 1590 Metal Husky Plastic Husky 2150 Plastic Husky 2150 Metal Husky 2200 Plastic Husky 3300 Plastic Husky 3300 Metal 1-1/2 in (38.1 mm) 1-1/2 in (38.1 mm) 1-1/2 in (38.1 mm) 2 in (50.8 mm) 2 in (50.8 mm) 2 in (50.8 mm) 3 in (76.2 mm) 3 in (76.2 mm) NSI Flange NPT or SPT DIN/NSI NSI Flange NPT or SPT DIN/NSI DIN/NSI NPT and SPT DIN/NSI (L only) Standard and Remote Standard and Remote Standard Standard and Remote Standard and Remote Standard Standard Standard 100 gpm (379 lpm) 100 gpm (379 lpm) 120 gpm (454 lpm) 150 gpm (568 lpm) 150 gpm (568 lpm) 200 gpm (757 lpm) 280 gpm (1,059 lpm)** 300 gpm (1,135 lpm)** 120 psi (8.3 bar, 0.8 MPa) 120 psi (8.3 bar, 0.8 MPa) 125 psi (8.6 bar, 0.9 MPa) 120 psi (8.3 bar, 0.8 MPa) 120 psi (8.3 bar, 0.8 MPa) 125 psi (8.6 bar, 0.9 MPa) 100 psi (7 bar, 0.7 MPa) 125 psi (8.6 bar, 0.9 MPa) with L center Polypropylene, PVDF luminum, 316 SST Polypropylene, PVDF Polypropylene, PVDF luminum, 316 SST, Ductile Iron Polypropylene, PVDF Polypropylene luminum, 316 SST oated luminum, 316 SST oated luminum, 316 SST Polypropylene oated luminum, 316 SST oated luminum, 316 SST Polypropylene Polypropylene luminum, Polypropylene* (*SST pump only) 35 lb (16 kg) Polypropylene 33.5 lb (15.2 kg) luminum 57 lb (25.9 kg) Polypropylene 49 lb (22 kg) Polypropylene 58 lb (26.3 kg) luminum 80 lb (36.3 kg) Polypropylene 200 lb (90.7 kg) Polypropylene 150 lb (68 kg) luminum 49 lb (22 kg) PVDF 86 lb (40 kg) SST 74 lb (33.6 kg) PVDF 68 lb (31 kg) PVDF 111 lb (50.3 kg) SST 106 lb (48.1 kg) PVDF 255 lb (115.6 kg) SST 130 lb (59 kg) Ductile Iron in (4.8 mm) in (4.8 mm) 0.25 in (6.3 mm) 0.25 in (6.3 mm) 0.25 in (6.3 mm) in (9.5 mm) 0.5 in (12.7 mm) 0.5 in (12.7 mm) Up to 15,000 cps Up to 15,000 cps Up to 15,000 cps Up to 20,000 cps Up to 20,000 cps Up to 20,000 cps Up to 20,000 cps Up to 20,000 cps **Maximum flow rate using standard diaphragm at 125 psi (8.6 bar). 7

10 Pump Selection Key Husky ir-operated Double Diaphragm Pumps Diaphragm Pump Designation Key For Husky 205, 307, 515, 716, 1590 and 2150 Pumps Part numbers are located on ID tag on center section of all Husky diaphragm pumps. D X X X X X Diaphragm Pump Pump Size Wetted Parts Seats alls/ hecks Diaphragms PUMP SIZE (air motor type and material) WETTED PRTS SETS LLS/HEKS DIPHRGM 1 = 1/4 (6.35 mm) Standard: Polypropylene center section 2 = 1/4 (6.35 mm) Remote: Polypropylene center section 3 = 3/8 (9.52 mm) Standard: Polypropylene center section 5 = 1/2 (12.7 mm) Standard: Polypropylene center section 4 = 1/2 (12.7 mm) Remote: Polypropylene center section 5 = 3/4 (19.05 mm) Standard: Polypropylene center section 4 = 3/4 (19.05 mm) Remote: Polypropylene center section = 1-1/2 (38.1 mm) Standard: aluminum center section = 1-1/2 (38.1 mm) Remote: aluminum center section T = 1-1/2 (38.1 mm) Standard: stainless steel center section U = 1-1/2 (38.1 mm) Remote: stainless steel center section F = 2 (50.8 mm) Standard: aluminum center section G = 2 (50.8 mm) Remote: aluminum center section V = 2 (50.8 mm) Standard: stainless steel center section 1 = cetal (npt) 2 = Polypropylene (npt) 3 = luminum (npt) 4 = Stainless Steel (npt) 5 = PVDF (npt) 6 = Ductile Iron (npt) = cetal * (bsp) = Polypropylene * (bsp) = luminum (bsp) D = Stainless Steel (bsp) E = PVDF (bsp) F = Ductile Iron (bsp) G = 2 bsp lum Extended H = 2 npt lum Extended 2 = cetal 3 = Stainless Steel 4 = Hardened SST 5 = TPE 6 = Santoprene 7 = una-n 8 = Fluoroelastomer 9 = Polypropylene = PVDF = SST with FKM seal = Santoprene with FKM seal G = Geolast 1 = PTFE 2 = cetal 3 = Stainless Steel 4 = Hardened SST 5 = TPE 6 = Santoprene 7 = una-n 8 = Fluoroelastomer 9 = Polypropylene = PVDF G = Geolast 1 = PTFE 5 = TPE 6 = Santoprene 7 = una-n 8 = Fluoroelastomer G = Geolast * = SP plastic in 1/2 (12.7mm) pumps >1 Plastic pumps flange connections Note: bove matrix is possible combinations. ll combination may not be available. See specific pump listings for available combinations. Diaphragm Pump Kit Designation Key When selecting a kit, use the same code numbers as for the pumps regarding pump size, seat, ball/checks and diaphragm. D O X X X X Diaphragm Pump Kit Pump Size Seats alls/ hecks Diaphragms PUMP SIZE SETS LLS/HEKS DIPHRGM 1 = 1/4 in (6.35 mm) 3 = 3/8 in (9.52 mm) 5 = 1/2 in (12.7 mm) and 3/4 in (19.05 mm) = 1-1/2 in (38.1 mm) metal pump = 1-1/2 in (38.1 mm) plastic pump F = 2 in (50.8 mm) metal pump G = 2 in (50.8 mm) plastic pump 0 = No seat 2 = cetal 3 = Stainless Steel 4 = Hardened SST 5 = TPE 6 = Santoprene 7 = una-n 8 = Fluoroelastomer 9 = Polypropylene = PVDF = SST with FKM seal = Santoprene with FKM seal G = Geolast 1 = PTFE 2 = cetal 3 = Stainless Steel 4 = Hardened SST 5 = TPE 6 = Santoprene 7 = una-n 8 = Fluoroelastomer 9 = Polypropylene = PVDF G = Geolast 0 = No alls/hecks 1 = PTFE 5 = TPE 6 = Santoprene 7 = una-n 8 = Fluoroelastomer G = Geolast 0 = No Diaphragm 8

11 Pump Selection Key ir-operated Double Diaphragm Pumps ir-operated Pump Selector Tool For Husky, hemsafe, Piston, and Sanitary Pumps Find the Right Pump for your pplication To order a Husky or hemsafe pump, use the online selector tool at or contact your distributor. From the homepage at click on selector for desired pump. Example of Product Selector Tool on Maximum Diaphragm Operating Temperature NOTIE: Temperature limits are based on mechanical stress only. ertain chemicals will further limit the fluid temperature range. Stay within the temperature range of the most-restricted wetted component. Operating at a fluid temperature that is too high or too low for the components of your pump may cause equipment damage. cetal Pumps Polypropylene or 180 ºF onductive Poly Pumps 150 ºF 32 ºF cetal una FKM Fluoro Geolast Polychloroprene Polypropylene PTFE Overmold PTFE heck PVDF Diaphragm/all/Seat Material Santoprene luminum, Hastelloy, or Stainless Steel Pumps TPE 150 ºF 100 ºF 50 ºF 150 ºF 32 ºF cetal una FKM Fluoro Geolast Polychloroprene Polypropylene PTFE Overmold PTFE heck PVDF Diaphragm/all/Seat Material Santoprene TPE 150 ºF 100 ºF 50 ºF 275 ºF 225 ºF 180 ºF 32 ºF 10 ºF -40 ºF cetal una FKM Fluoro Geolast Polychloroprene Polypropylene PTFE Overmold PTFE heck PVDF Diaphragm/all/Seat Material Santoprene TPE 250 ºF 200 ºF 150 ºF 100 ºF 50 ºF 0 ºF -50 ºF 225 ºF 180 ºF 32 ºF 10 ºF cetal una PVDF Pumps FKM Fluoro Geolast Polychloroprene Polypropylene PTFE Overmold PTFE heck PVDF Diaphragm/all/Seat Material Santoprene TPE 200 ºF 150 ºF 100 ºF 50 ºF 0 ºF The maximum temperature listed is based on the TEX standard for T4 temperature classification. If you are operating in a non-explosive environment, FKM fluoroelastomer s maximum fluid temperature in aluminum or stainless steel pumps is 320 F (160 ). ctual pump performance may be affected by prolonged usage at temperature. 9

12 Pump Selection Key Fluid Section Materials luminum Medium corrosion and abrasion resistance. Not for use with halogenated hydrocarbons. Polypropylene Wide chemical compatibility. General purpose. onductive Polypropylene Wide chemical compatibility. General purpose. Groundable. Stainless Steel (316 Grade) High level of corrosion and abrasion resistance. cetal Ductile Iron Wide range of solvent resistance. Withstands extreme fatigue. Good level of abrasion resistance. Groundable for use with flammables. Not for use with acids or bases. High abrasion resistance. Hastelloy PVDF Good resistance to aggressive chemicals in corrosive environments. ompatible with high temperature fluids. Strong chemical resistance to acids and bases. Good abrasion resistance. High temperature resistance. PTFE Ideal for corrosive or toxic liquids. High temperature resistance and low coefficient of friction. UHMWPE est option for abrasion resistance. High level of chemical resistance. 10 Fluid section materials vary depending on pump model

13 Pump Selection Key Diaphragm Materials Diaphragm Material* Description PTFE/EPDM Two Piece Widest chemical compatibility, extreme corrosion resistance, very low frictional coefficient, non-adhesive, high heat resistance. PTFE/EPDM Overmolded Same as above. Overmolded design improves wear, durability and cleanability. Longer life than above. Thermoplastic Polyester Elastomer (TPE) Good low temp properties. Good abrasion resistance. Often substituted for una. Santoprene Good abrasion and chemical resistance. OK for use with some solvents (e. g. MEK, cetone), caustic solutions, dilute acids, and alcohols. Often substituted for EPDM or EPR. una-n Good for petroleum-based fluids, water, oils, hydrocarbons and MILD chemicals (e.g. mineral spirits). Fluoroelastomer (FKM) High heat resistance. Good resistance to aggressive chemicals including acids and some solvents (e.g. xylene and mineral spirits). Good resistance to steam as well as animal, vegetable, and petroleum oils. Resists unleaded fuels. Geolast Good abrasion resistance. pproximately same chemical compatibility as una. Polychloroprene Overmolded (R) High resilience. Good with whiskey, wine, beer and natural gas. One source calls an "all purpose Polymer ". bout 30% higher abrasion resistance than una. EPDM, used with 3 pump (Ethylene Propylene Diene M-class rubber) High heat resistance. Good resistance to gas permeability and to steam. OK with caustic solutions, dilute acids, ketones and alcohols. Recommended for use with IP Sanitizing gent OXONI. EPDM Overmolded Slurries with chemical mixtures. una-n Overmolded Oils and nonaggressive chemical slurries. *vailable materials of construction varies depending on pump model 11

14 Pump Selection Key all heck Materials all heck Material Thermoplastic Polyester Elastomer (TPE) Stainless Steel Santoprene Geolast una-n Fluoroelastomer (FKM) PTFE Polychloroprene (R) Polychloroprene (R) Weighted cetal Description Good low temperature properties. Good abrasion resistance. High level of corrosion and abrasion resistance. Passivated 316 grade. Good abrasion and chemical resistance. OK for use with some solvents, (e.g. MEK, acetone) caustic solutions, dilute acids and alcohols. Often substituted for EPDM or EPR. Good abrasion resistance. pproximately same chemical compatibility as una. Good for petroleum-based fluids, water, oils, hydrocarbons and MILD chemicals (e.g. mineral spirits). Not for use with strong solvents or chemicals (e.g. acetone, MEK, ozone, chrlorinated hydrocarbons and nitro hydrocarbons). High heat resistance. Good resistance to aggressive chemicals including acids and some solvents (e.g. Xylene and mineral spirits). Good resistance to steam as well as animal, vegetable and petroleum oils. Resists unleaded fuels. Not for use with ketones, low molecular weight ester and nitro containing compounds. Widest chemical compatibility, extreme corrosion resistance, very low frictional coefficient, non-adhesive, high heat resistance. Poor abrasion resistance. High resilience. Good with whiskey, wine, beer and natural gas. Good with animal and vegetable oil, moderate chemicals, fats and greases. Not for use with strong oxidizing acids, esters, ketones, chlorinated aromatic and nitro hydrocarbons. High resilience. Good with whiskey, wine, beer and natural gas. Good with animal and vegetable oil, moderate chemicals, fats and greases. Not for use with strong oxidizing acids, esters, ketones, chlorinated aromatic and nitro hydrocarbons. Wide range of solvent resistant and withstands extreme fatigue. Good level of abrasion resistance. Not for use with acids or bases. Seat Materials Seat Material Polypropylene Thermoplastic Polyester Elastomer (TPE) Stainless Steel Santoprene Geolast una-n Fluoroelastomer (FKM) luminum cetal PVDF PTFE UHMWPE Description Wide chemical compatibility. General purpose. Good low temp properties. Good abrasion resistance. High level of corrosion and abrasion resistance. Passivated 316 grade. Good abrasion and chemical resistance. OK for use with some solvents, (e.g. MEK, acetone) caustic solutions, dilute acids, and alcohols. Often substituted for EPDM or EPR. Good abrasion resistance. pproximately same chemical compatibility as una. Good for petroleum-based fluids, water, oils, hydrocarbons and MILD chemicals (e.g. mineral spirits). Not for use with strong solvents or chemicals (e. g. acetone, MEK, ozone, chrlorinated hydrocarbons, and nitro hydrocarbons). High heat resistance. Good resistance to aggressive chemicals including acids and some solvents (e. g. Xylene and mineral spirits). Good resistance to steam as well as animal, vegetable and petroleum oils. Resists unleaded fuels. Not for use with ketones, low molecular weight ester and nitro containing compounds. Medium corrosion and abrasion resistance. Not for use with halogenated hydrocarbons. Wide range of solvent resistant and withstands extreme fatigue. Good level of abrasion resistance. Not for use with acids or bases. Strong chemical resistance: cids and bases. Good abrasion resistance. High temperature resistance. Ideal for corrosive or toxic liquids. High temperature resistance. est option for adrasion resistance. High level of chemical resistance. 12

15 hemsafe 205 Plastic Pumps ir-operated Double Diaphragm Selector Tool To order a hemsafe 205, use the online selector tool at or contact your distributor. NOTE: heck the identification plate (ID) for the onfiguration Number of your pump. Use the following matrix to define the components of your pump. Example of Product Selector Tool on Pump onfiguration Options Pump Model (1/4 inch port, 3.6 gpm) 205PT 1/4 in PTFE 205UH 1/4 in UHMWPE enter Section and ir Valve Material P01 Polypropylene center with npt air inlet P03 Polypropylene center with bspt air inlet Fluid overs and Manifolds Seat Material all Material PT3 PTFE, NPT PT PTFE PT PTFE PT4 PTFE, SPT UM UHMWPE UH3 UHMWPE, NPT UH4 UHMWPE, SPT Manifold and Seat Diaphragm Material Seal Material N una-n Overmolded* PT PTFE EP EPDM Overmolded* PO PTFE Overmolded *Only available on 205UH 13

16 hemsafe 205 Plastic Pumps Popular Models Part Number Model Fluid Path Seat all Port Diaphragm 24X430 hemsafe 205 PTFE PTFE PTFE SPT Overmolded PTFE 24X429 hemsafe 205 PTFE PTFE PTFE NPT Overmolded PTFE 24X532 hemsafe 205 UHMWPE UHMWPE PTFE SPT Overmolded EPDM 24X533 hemsafe 205 UHMWPE UHMWPE PTFE NPT Overmolded EPDM 24X508 hemsafe 205 UHMWPE UHMWPE PTFE SPT Overmolded una-n 24X507 hemsafe 205 UHMWPE UHMWPE PTFE NPT Overmolded una-n 24X511 hemsafe 205 UHMWPE UHMWPE PTFE SPT Overmolded PTFE 24X509 hemsafe 205 UHMWPE UHMWPE PTFE NPT Overmolded PTFE Technical Specifications hemsafe 205 Polypropylene Max Flow Rate* 3.7 gpm (14 lpm) Displacement Per ycle gal (0.03 l) onnection Sizes/Types 1/4" NPT, 1/4" SPT Max. Pumpable Solids 0.06 in (1.5 mm) Suction Lift Dry* 6.5 ft (2.0 m) Suction Lift Wet* 31 ft (9.5 m) Weight (PTFE) 4.1 lb (1.9 kg) Weight (UHMWPE) 4 lb (1.8 kg) Max ir/fluid Temperature PTFE 212 F (100 ) UHMWPE 158 F (70 ) Min/Max ir Pressure 30 psi (2 bar) minimum startup air pressure 100 psi (7 bar) maximum supply air pressure Max. Sound Pressure 70.6 d(a) Max. Sound Power 64.2 d(a) Instruction Manual *May vary depending on materials 14

17 hemsafe 205 Plastic Pumps Performance harts Dimensions FLUID OUTLET PRESSURE psi (bar, MPa) (7.0, 0.70) 90 (6.2, 0.62) 80 (5.5, 0.55) 70 (4.9, 0.49) 60 (4.2, 0.42) 50 (3.5, 0.35) 40 (2.8, 0.28) 30 (2.1, 0.21) 20 (1.4, 0.14) 10 (0.7, 0.07) 0 gpm (lpm) (1.9) 1.0 (3.8) hemsafe 205 Performance pprox. ycles per Minute 1.5 (5.7) 2.0 (7.6) 2.5 (9.5) 3.0 (11.4) FLUID FLOW (Pump tested in water with inlet submerged) 3.5 (13.2) 9.0 (0.25) 7.2 (0.20) 6.4 (0.18) 5.6 (0.15) 4.8 (0.13) 4.0 (0.11) 3.2 (0.09) 2.4 (0.06) 1.6 (0.04) 0.8 (0.02) IR ONSUMPTION scfm (m 3 /min) 4.3 in. (113 mm) 1.1 in. (28 mm) 2.7 in. (69 mm) 5.5 in. (139 mm) 1/4 in. NPT or SPT IR PRESSURE = at 100 psi (7 bar, 0.7 MPa) = at 70 psi (4.8 bar, 0.48 MPa) = at 40 psi (2.8 bar, 0.28 MPa) LEGEND ir onsumption Fluid Pressure 1/8 in. NPT or SPT 6.5 in. (166 mm) 4.2 in. (107 mm) 3.3 in. (83 mm) Mounting Pattern 2.8 in. (70 mm) 0.3 in. (7 mm) 2.5 in. (64 mm) 15

18 hemsafe 307 Plastic Pump ir-operated Double Diaphragm Selector Tool To order a hemsafe 307, use the online selector tool at or contact your distributor. NOTE: heck the identification plate (ID) for the onfiguration Number of your pump. Use the following matrix to define the components of your pump. Example of Product Selector Tool on Pump onfiguration Options Pump Model (3/8 inch port, 7.9 gpm) 307PT 3/8 in PTFE 307UH 3/8 in UHMWPE enter Section and ir Valve Material P01 Polypropylene center with npt air inlet P03 Polypropylene center with bspt air inlet Fluid overs and Manifolds Seat Material all Material PT3 PTFE, NPT PT PTFE PT PTFE PT4 PTFE, SPT UH UHMWPE UH3 UHMWPE, NPT UH4 UHMWPE, SPT Manifold and Seat Diaphragm Material Seal Material N una-n Overmolded* PT PTFE EP EPDM Overmolded* PO PTFE Overmolded *Only available on 307UH 16

19 hemsafe 307 Plastic Pumps Popular Models Part Number Model Fluid Path Seat all Port Diaphragm 24X428 hemsafe 307 PTFE PTFE PTFE SPT Overmolded PTFE 24X427 hemsafe 307 PTFE PTFE PTFE NPT Overmolded PTFE 24X536 hemsafe 307 UHMWPE UHMWPE PTFE SPT Overmolded EPDM 24X537 hemsafe 307 UHMWPE UHMWPE PTFE NPT Overmolded EPDM 24X502 hemsafe 307 UHMWPE UHMWPE PTFE SPT Overmolded una-n 24X501 hemsafe 307 UHMWPE UHMWPE PTFE NPT Overmolded una-n 24X504 hemsafe 307 UHMWPE UHMWPE PTFE SPT Overmolded PTFE 24X503 hemsafe 307 UHMWPE UHMWPE PTFE NPT Overmolded PTFE Technical Specifications hemsafe 307 Polypropylene Max Flow Rate* 6.7 gpm (25 lpm) Displacement Per ycle gal (0.07 l) onnection Sizes/Types 3/8" NPT, 3/8" SPT Max. Pumpable Solids 0.08 in (2.0 mm) Suction Lift Dry* 10 ft (3.0 m) Suction Lift Wet* 31 ft (9.5 m) Weight (PTFE) 6.8 lb (3.1 kg) Weight (UHMWPE) 6 lb (2.7 kg) Max ir/fluid Temperature PTFE 212 F (100 ) UHMWPE 158 F (70 ) Min/Max ir Pressure 30 psi (2 bar) minimum startup air pressure 100 psi (7 bar) maximum supply air pressure Max. Sound Pressure 66.1 d(a) Max. Sound Power 58.1 d(a) Instruction Manual *May vary depending on materials 17

20 hemsafe 307 Plastic Pumps Performance harts Dimensions FLUID OUTLET PRESSURE psi (bar, MPa) hemsafe 307 Performance pprox. ycles per Minute (7.0, 0.70) (0.28) (6.2, 0.62) 80 (0.25) 8.0 (5.5, 0.55) (0.22) (4.9, 0.49) 60 (0.20) 6.0 (4.2, 0.42) (0.17) (3.5, 0.35) 40 (0.14) 4.0 (2.8, 0.28) (0.11) (2.1, 0.21) 20 (1.4, 0.14) 10 (0.7, 0.07) (0.08) 2.0 (0.05) 1.0 (0.03) 0 gpm (lpm) (3.8) (7.6) (11.4) (15.1) (18.9) (22.7) (26.5) IR ONSUMPTION scfm (m 3 /min) 5.3 in. (135 mm) 3.0 in. (76 mm) 5.9 in. (150 mm) 3/8 in. NPT or SPT FLUID FLOW (Pump tested in water with inlet submerged) IR PRESSURE = at 100 psi (7 bar, 0.7 MPa) = at 70 psi (4.8 bar, 0.48 MPa) = at 40 psi (2.8 bar, 0.28 MPa) LEGEND ir onsumption Fluid Pressure 1.1 in. (28 mm) 1/8 in. NPT or SPT 7.6 in. (193 mm) 4.9 in. (124 mm) 3.5 in. (89 mm) Mounting Pattern 3.0 in. (76 mm) 0.3 in. (7 mm) 3.0 in. (76 mm) 18

21 hemsafe 515 Plastic Pumps ir-operated Double Diaphragm Selector Tool To order a hemsafe 515, use the online selector tool at or contact your distributor. NOTE: heck the identification plate (ID) for the onfiguration Number of your pump. Use the following matrix to define the components of your pump. Example of Product Selector Tool on Pump onfiguration Options Pump Model (1/2 inch port, 16.6 gpm) 515PT 1/2 in PTFE 515UH 1/2 in UHMWPE enter Section and ir Valve Material P01 Polypropylene center with npt air inlet P03 Polypropylene center with bspt air inlet Fluid overs and Manifolds Seat Material all Material PT3 PTFE, NPT PT PTFE PT PTFE PT4 PTFE, SPT UH UHMWPE UH3 UHMWPE, NPT UH4 UHMWPE, SPT Manifold and Seat Diaphragm Material Seal Material N una-n Overmolded* PT PTFE EP EPDM Overmolded* PO PTFE Overmolded *Only available on 515UH 19

22 hemsafe 515 Plastic Pump Popular Models Part Number Model Fluid Path Seat all Port Diaphragm 24X426 hemsafe 515 PTFE PTFE PTFE SPT Overmolded PTFE 24X425 hemsafe 515 PTFE PTFE PTFE NPT Overmolded PTFE 24X540 hemsafe 515 UHMWPE UHMWPE PTFE SPT Overmolded EPDM 24X541 hemsafe 515 UHMWPE UHMWPE PTFE NPT Overmolded EPDM 24X496 hemsafe 515 UHMWPE UHMWPE PTFE SPT Overmolded una-n 24X495 hemsafe 515 UHMWPE UHMWPE PTFE NPT Overmolded una-n 24X498 hemsafe 515 UHMWPE UHMWPE PTFE SPT Overmolded PTFE 24X497 hemsafe 515 UHMWPE UHMWPE PTFE NPT Overmolded PTFE Technical Specifications hemsafe 515 Polypropylene Max Flow Rate* 16 gpm (60.6 lpm) Displacement Per ycle gal (0.16 l) onnection Sizes/Types 1/2" NPT, 1/2" SPT Max. Pumpable Solids 0.16 in (4.1 mm) Suction Lift Dry* 11 ft (3.3 m) Suction Lift Wet* 31 ft (9.5 m) Weight (PTFE) 20 lb (9.1 kg) Weight (UHMWPE) 13.7 lb (6.2 kg) Max ir/fluid Temperature PTFE 212 F (100 ) UHMWPE 158 F (70 ) Min/Max ir Pressure 30 psi (2 bar) minimum startup air pressure 100 psi (7 bar) maximum supply air pressure Max. Sound Pressure 82.0 d(a) Max. Sound Power 74.8 d(a) Instruction Manual *May vary depending on materials 20

23 hemsafe 515 Plastic Pump Performance harts Dimensions FLUID OUTLET PRESSURE psi (bar, MPa) hemsafe 515 Performance pprox. ycles per Minute (7.0, 0.70) 30.0 (0.85) 90 (6.2, 0.62) (0.76) 24.0 (5.5, 0.55) 70 (4.9, 0.49) (0.68) 21.0 (0.60) 60 (4.2, 0.42) 18.0 (0.51) 50 (3.5, 0.35) 40 (2.8, 0.28) 15.0 (0.42) 12.0 (0.34) (2.1, 0.21) 20 (1.4, 0.14) 10 (0.7, 0.07) (0.25) 6.0 (0.17) 3.0 (0.08) 0 gpm (lpm) (7.6) (15.1) (22.7) (30.3) (37.9) (45.4) (53.0) (60.6) IR ONSUMPTION scfm (m 3 /min) 8.0 in. (20.3 cm) 9.2 in. (23.4 cm) 4.6 in. (11.7 cm) 1/2 in. NPT or SPT FLUID FLOW (Pump tested in water with inlet submerged) 1.6 in. (4.1 cm) IR PRESSURE = at 100 psi (7 bar, 0.7 MPa) = at 70 psi (4.8 bar, 0.48 MPa) = at 40 psi (2.8 bar, 0.28 MPa) LEGEND ir onsumption Fluid Pressure 1/4 in. NPT or SPT 10.9 in. (27.7 cm) 8.5 in. (21.6 cm) 6.0 in. (15.2 cm) 21

24 hemsafe 1040 Plastic Pump ir-operated Double Diaphragm Selector Tool To order a hemsafe 1040, use the online selector tool at or contact your distributor. NOTE: heck the identification plate (ID) for the onfiguration Number of your pump. Use the following matrix to define the components of your pump. Example of Product Selector Tool on Pump onfiguration Options Pump Model (1 inch port, 37.5 gpm) 1040PT 1 in PTFE 1040UH 1 in UHMWPE enter Section and ir Valve Material P01 Polypropylene center with npt air inlet P03 Polypropylene center with bspt air inlet Fluid overs and Manifolds Seat Material all Material PT3 PTFE, NPT PT PTFE PT PTFE PT4 PTFE, SPT UH UHMWPE UH3 UHMWPE, NPT UH4 UHMWPE, SPT Manifold and Seat Diaphragm Material Seal Material N una-n Overmolded* PT PTFE EP EPDM Overmolded* PO PTFE Overmolded *Only available on 1040UH 22

25 hemsafe 1040 Plastic Pump Popular Models Part Number Model Fluid Path Seat all Port Diaphragm 24X424 hemsafe 1040 PTFE PTFE PTFE SPT Overmolded PTFE 24X423 hemsafe 1040 PTFE PTFE PTFE NPT Overmolded PTFE 24X544 hemsafe 1040 UHMWPE UHMWPE PTFE SPT Overmolded EPDM 24X545 hemsafe 1040 UHMWPE UHMWPE PTFE NPT Overmolded EPDM 24X490 hemsafe 1040 UHMWPE UHMWPE PTFE SPT Overmolded una-n 24X489 hemsafe 1040 UHMWPE UHMWPE PTFE NPT Overmolded una-n 24X492 hemsafe 1040 UHMWPE UHMWPE PTFE SPT Overmolded PTFE 24X491 hemsafe 1040 UHMWPE UHMWPE PTFE NPT Overmolded PTFE Technical Specifications hemsafe 1040 Polypropylene Max Flow Rate* 38.8 gpm (146 lpm) Displacement Per ycle gal (0.56 l) onnection Sizes/Types 1" NPT, 1" SPT Max. Pumpable Solids 0.24 in (6.1 mm) Suction Lift Dry* 13 ft (4.0 m) Suction Lift Wet* 31 ft (9.5 m) Weight (PTFE) 40 lb (18 kg) Weight (UHMWPE) 26.4 lb (12 kg) Max ir/fluid Temperature PTFE 212 F (100 ) UHMWPE 158 F (70 ) Min/Max ir Pressure 30 psi (2 bar) minimum startup air pressure 100 psi (7 bar) maximum supply air pressure Max. Sound Pressure 83.3 d(a) Max. Sound Power 78.3 d(a) Instruction Manual *May vary depending on materials 23

26 hemsafe 1040 Plastic Pump Performance harts Dimensions FLUID OUTLET PRESSURE psi (bar, MPa) hemsafe 1040 Performance pprox. ycles per Minute (7.0, 0.70) 50.0 (1.41) (6.2, 0.62) (1.27) (5.5, 0.55) (1.13) 70 (4.9, 0.49) (0.99) 30.0 (4.2, 0.42) 50 (3.5, 0.35) 40 (2.8, 0.28) (0.85) 25.0 (0.70) 20.0 (0.56) 30 (2.1, 0.21) 20 (1.4, 0.14) 10 (0.7, 0.07) 15.0 (0.42) 10.0 (0.28) 5.0 (0.14) 0 gpm (lpm) (15.1) (30.3) (45.4) (60.6) (75.7) (90.8) (106.0) (121.0) (136.0) (151.0) IR ONSUMPTION scfm (m 3 /min) 10.4 in. (26.4 cm) 5.4 in. (13.7 cm) 10.9 in. (27.7 cm) 1 in. NPT or SPT FLUID FLOW (Pump tested in water with inlet submerged) 1.9 in. (4.8 cm) IR PRESSURE = at 100 psi (7 bar, 0.7 MPa) = at 70 psi (4.8 bar, 0.48 MPa) = at 40 psi (2.8 bar, 0.28 MPa) LEGEND ir onsumption Fluid Pressure 1/4 in. NPT or SPT 14.1 in. (35.8 cm) 10.5 in. (26.7 cm) 8.0 in. (20.3 cm) 24

27 hemsafe 1590 Plastic Pumps ir-operated Double Diaphragm Selector Tool To order a hemsafe 1590, use the online selector tool at or contact your distributor. NOTE: heck the identification plate (ID) for the onfiguration Number of your pump. Use the following matrix to define the components of your pump. Example of Product Selector Tool on Pump onfiguration Options Pump Model (1.5 inch port, 85.2 gpm) 1590PT 1.5 in PTFE 1590UH 1.5 in UHMWPE enter Section and ir Valve Material P01 Polypropylene center with npt air inlet P03 Polypropylene center with bspt air inlet Fluid overs and Manifolds Seat Material all Material PT3 PTFE, NPT PT PTFE PT PTFE PT4 PTFE, SPT UH UHMWPE UH3 UHMWPE, NPT UH4 UHMWPE, SPT Manifold and Seat Diaphragm Material Seal Material N una-n Overmolded* PT PTFE EP EPDM Overmolded* PO PTFE Overmolded *Only available on 1590UH 25

28 hemsafe 1590 Plastic Pump Popular Models Part Number Model Fluid Path Seat all Port Diaphragm 24X422 hemsafe 1590 PTFE PTFE PTFE SPT Overmolded PTFE 24X421 hemsafe 1590 PTFE PTFE PTFE NPT Overmolded PTFE 24X549 hemsafe 1590 UHMWPE UHMWPE PTFE SPT Overmolded EPDM 24X551 hemsafe 1590 UHMWPE UHMWPE PTFE NPT Overmolded EPDM 24X514 hemsafe 1590 UHMWPE UHMWPE PTFE SPT Overmolded una-n 24X515 hemsafe 1590 UHMWPE UHMWPE PTFE NPT Overmolded una-n 24X486 hemsafe 1590 UHMWPE UHMWPE PTFE SPT Overmolded PTFE 24X485 hemsafe 1590 UHMWPE UHMWPE PTFE NPT Overmolded PTFE Technical Specifications hemsafe 1590 Max Flow Rate* Polypropylene 99.5 gpm (376 lpm) Displacement Per ycle gal (1.64 l) onnection Sizes/Types Max. Pumpable Solids 1-1/2" NPT, 1-1/2" SPT 0.32 in (8.1 mm) Suction Lift Dry* 16 ft (4.9 m) Suction Lift Wet* 31 ft (9.5 m) Weight (PTFE) Weight (UHMWPE) Max ir/fluid Temperature Min/Max ir Pressure Max. Sound Pressure 95.2 lb (43.2 kg) 66 lb (30 kg) PTFE 212 F (100 ) UHMWPE 158 F (70 ) 30 psi (2 bar) minimum startup air pressure 100 psi (7 bar) maximum supply air pressure 89.8 d(a) Max. Sound Power 91.1 d(a) Instruction Manual *May vary depending on materials 26

29 hemsafe 1590 Plastic Pump Performance harts Dimensions FLUID OUTLET PRESSURE psi (bar, MPa) hemsafe 1590 Performance pprox. ycles per Minute (7.0, 0.70) 110 (3.11) 90 (6.2, 0.62) (2.80) 88 (5.5, 0.55) 70 (4.9, 0.49) (2.49) 77 (2.18) (4.2, 0.42) 50 (3.5, 0.35) 40 (1.87) 55 (1.56) 44 (2.8, 0.28) (1.24) (2.1, 0.21) 20 (1.4, 0.14) 10 (0.7, 0.07) (0.93) 22 (0.62) 11 (0.31) 0 gpm (lpm) (37.8) (75.7) (114) (151) (189) (227) (265) (303) (341) (378) IR ONSUMPTION scfm (m 3 /min) 15.2 in. (38.6 cm) 7.8 in. (19.8 cm) 15.5 in. (39.3 cm) 1-1/2 in. NPT or SPT FLUID FLOW (Pump tested in water with inlet submerged) IR PRESSURE = at 100 psi (7 bar, 0.7 MPa) = at 70 psi (4.8 bar, 0.48 MPa) = at 40 psi (2.8 bar, 0.28 MPa) LEGEND ir onsumption Fluid Pressure 2.4 in. (6.1 cm) 1/2 in. NPT or SPT 20.0 in. (50.8 cm) 13.1 in. (33.2 cm) 9.8 in. (24.9 cm) 27

30 Notes 28

31 Husky 205 Plastic Pumps ir-operated Double Diaphragm Ordering Information D X X X X X Diaphragm Pump Pump Size Wetted Parts Seats alls/ hecks Diaphragms PUMP SIZE (air motor type and material) WETTED PRTS SETS HEK VLVES DIPHRGM 1 = 1/4 (6.35 mm) Standard: polypropylene center section 1 = cetal (npt) 0 = No Seats 2 = cetal 1 = PTFE 2 = 1/4 (6.35 mm) Remote: polypropylene center section 2 = Poly (npt) 9 = Polypropylene 6 = Santoprene 5 = PVDF (npt) = PVDF Popular Models Part Number Part Number (NPT Ported) (SP Ported) Material Standard ir Valve Remote* ir Valve Standard ir Valve Remote* ir Valve Materials for heck Valves Materials for Diaphragms Fluid Kit ir Kit ir ontrol** cetal D11021 D21021 D11021 D21021 cetal PTFE D D11026 D21026 D11026 D21026 cetal Santoprene D PVDF D1501 D2501 D1501 D2501 PVDF PTFE D D1506 D2506 D1506 D2506 PVDF Santoprene D Polypropylene D12091 D22091 D12091 D22091 Polypropylene PTFE D D12096 D22096 D12096 D22096 Polypropylene Santoprene D * Requires ycleflo or external valve control ** ir control includes air regulator and filter with gauge Technical Specifications Wall bracket standard with pump Husky 205 Plastic Pumps cetal Polypropylene PVDF Maximum fluid working pressure 100 psi (7 bar, 0.7 MPa) 100 psi (7 bar, 0.7 MPa) 100 psi (7 bar, 0.7 MPa) Maximum free flow delivery* 5.0 gpm (18.9 lpm) 5.0 gpm (18.9 lpm) 5.0 gpm (18.9 lpm) Maximum pump speed 250 cpm 250 cpm 250 cpm Displacement per cycle** gallon (0.045 liter) gallon (0.045 liter) gallon (0.045 liter) Maximum suction lift (D12096) 10 ft (3 m) dry 10 ft (3 m) dry 10 ft (3 m) dry Maximum size pumpable solids 0.06 in (1.5 mm) 0.06 in (1.5 mm) 0.06 in (1.5 mm) Maximum ambient operating temperature*** 180 F (82 ) 150 F (66 ) 180 F (82 ) Maximum diaphragm operating temperature*** Refer to page 7 Refer to page 7 Refer to page 7 Typical sound level at 70 psi 70 da 70 da 70 da (4.9 bar, 0.49 MPa) 125 cpm Maximum air consumption 9.0 scfm (0.252 m3/min) 9.0 scfm (0.252 m3/min) 9.0 scfm (0.252 m3/min) ir pressure operating range 20 to 100 psi (1.4 to 7 bar, 0.14 to 0.7 MPa) 20 to 100 psi (1.4 to 7 bar, 0.14 to 0.7 MPa) 20 to 100 psi (1.4 to 7 bar, 0.14 to 0.7 MPa) ir inlet size 1/4 npt(f) 1/4 npt(f) 1/4 npt(f) ir exhaust port size 1/4 npt(f) 1/4 npt(f) 1/4 npt(f) Fluid inlet & outlet size**** 1/4 npt(f) 1/4 npt(f) 1/4 npt(f) Weight 2.5 lb (1.1 kg) 2.0 lb (0.9 kg) 2.8 lb (1.3 kg) Wetted parts (in addition to ball, seat and diaphragm materials which may vary by pump) cetal with Stainless Steel fibers, PTFE, cetal, Santoprene Glass-filled Polypropylene, Santoprene, PTFE, Polypropylene Instruction manual ** Displacement per cycle may vary based on suction condition, discharge head, air pressure and fluid type *** ctual pump performance may be affected by prolonged usage at temperature **** Hybrid thread allows for either 1/4 npt or 1/4 bspt fitting PVDF, PTFE, Santoprene 29

32 Husky 205 Plastic Pumps Performance harts Dimensions 120 (8, 0.8) Husky 205 Performance 6 (0.17) ir Inlet 1/4 in npt(f) FLUID OUTLET PRESSURE psi (bar, MPa) 100 (7, 0.7) 80 (5.5, 0.55) 60 (4.1, 0.41) 40 (2.8, 0.28) 20 (1.4, 0.14) 5 (0.14) 4 (0.11) 3 (0.085) 2 (0.057) 1 (0.028) IR ONSUMPTION scfm (m 3 /min) 0 gpm (lpm) (1.9) 1 (3.8) 1.5 (3.8) 2 (7.6) 2.5 (9.5) FLUID FLOW (Pump tested in water with inlet submerged 3 (11.4) 3.5 (13.3) 6.8 in (173 mm) IR PRESSURE LEGEND = at 100 psi (7 bar, 0.7 MPa) ir onsumption = at 70 psi (4.8 bar, 0.48 MPa) Fluid Pressure = at 40 psi (2.8 bar, 0.28 MPa) 6 in (145 mm) Typical System Drawings 3.7 in (94 mm) Fluid Inlet/Outlet 1/4 in npt/bsp Husky 205 Wall-Mount (shown with ycleflo controller) 30

33 Husky 307 Plastic Pumps ir-operated Double Diaphragm Ordering Information D X X X X X Diaphragm Pump Pump Size Wetted Parts Seats alls/ hecks Diaphragms PUMP SIZE (air motor type and material) WETTED PRTS SETS LLS DIPHRGM 3 = 3/8 (9.52 mm) Standard: polypropylene center section 1 = cetal (npt) 2 = cetal 1 = PTFE 1 = PTFE 2 = Poly (npt) 3 = Stainless Steel 3 = SST 5 = TPE 9 = Polypropylene 5 = TPE 6 = Santoprene = cetal (bsp) 6 = Santoprene 7 = una N = Poly (bsp) 7 = una N Popular Models Part Number Part Number (NPT Ported) (SP Ported) Material Standard ir Valve Remote ir Valve Standard ir Valve Remote ir Valve Materials for Seats Materials for alls Materials for Diaphragms Fluid Kit ir Kit ir ontrol* cetal D31211 N D3211 N cetal PTFE PTFE D D31255 N D3255 N cetal TPE TPE D D31277 N D3277 N cetal una-n una-n D D31311 N D3311 N Stainless Steel PTFE PTFE D Polypropylene D32211 N D3211 N cetal PTFE PTFE D D32255 N D3255 N cetal TPE TPE D D32277 N D3277 N cetal una-n una-n D D32311 N D3311 N Stainless Steel PTFE PTFE D D32366 N D3366 N Stainless Steel Santoprene Santoprene D D32911 N D3911 N Polypropylene PTFE PTFE D D32955 N D3955 N Polypropylene TPE TPE D D32966 N D3966 N Polypropylene Santoprene Santoprene D D32977 N D3977 N Polypropylene una-n una-n D * ir control includes air regulator and filter with gauge (see drawing on page 13) 31

34 Husky 307 Plastic Pumps Technical Specifications Husky 307 Plastic Pumps cetal Polypropylene Maximum fluid working pressure 100 psi (7 bar, 0.7 MPa) 100 psi (7 bar, 0.7 MPa) Maximum free flow delivery* 7.0 gpm (26.5 lpm) 7.0 gpm (26.5 lpm) Maximum pump speed 330 cpm 330 cpm Displacement per cycle** 0.02 gallon (0.076 liter) 0.02 gallon (0.076 liter) Maximum suction lift (D31255) 12 ft (3.7 m) dry 12 ft (3.7 m) dry Maximum size pumpable solids 0.06 in (1.5 mm) 0.06 in (1.5 mm) Maximum ambient operating temperature*** 180 F (65.5 ) 150 F (65.5 ) Maximum diaphragm operating temperature*** Refer to page 7 Refer to page 7 Typical sound level at 50 psi 75 da 75 da (3.5 bar, 0.35 MPa) 50 cpm Maximum air consumption 6 scfm (0.17 m3/min) 6 scfm (0.17 m3/min) ir pressure operating range 20 to 100 psi (1.4 to 8.4 bar, 0.14 to 0.84 MPa) 20 to 100 psi (1.4 to 8.4 bar, 0.14 to 0.84 MPa) ir inlet size 1/4 npt(f) or bspt(f) 1/4 npt(f) or bspt(f) Fluid inlet & outlet size**** 3/8 npt(f) 3/8 npt(f) Weight 5.2 lb (2.4 kg) 4.75 lb (2.2 kg) Wetted parts (in addition to ball, seat and cetal with Stainless Polypropylene, PTFE diaphragm materials which may vary by pump) Steel fibers, PTFE Instruction manual *Flow rates are with muffler and do not vary based on diaphragm material **Displacement per cycle may vary based on suction condition, discharge head, air pressure and fluid type ***ctual pump performance may be affected by prolonged usage at temperature Performance hart 120 (8.4, 0.84) Husky 307 Performance 6 (0.17) FLUID OUTLET PRESSURE psi (bar, MPa) 100 (7, 0.7) 80 (5.5, 0.55) 60 (4.1, 0.41) 40 (2.8, 0.28) 20 (1.4, 0.14) 0 gpm (lpm) 0 1 (3.8) 2 (7.6) D D 3 (11.4) 4 (15.2) 5 (19.0) 6 (22.7) FLUID FLOW (Pump tested in water with inlet submerged 7 (26.5) 8 (30.0) 5 (0.14) 4 (0.11) 3 (0.085) 2 (0.057) 1 (0.028) IR ONSUMPTION scfm (m 3 /min IR PRESSURE LEGEND = at 100 psi (7 bar, 0.7 MPa) ir onsumption = at 70 psi (4.8 bar, 0.48 MPa) Fluid Pressure = at 40 psi (2.8 bar, 0.28 MPa) D = at 20 psi (1.4 bar, 0.14 MPa) 32

35 Husky 307 Plastic Pumps Dimensions 1/4 npt(f) ir Inlet 3.14 in (80 mm) 4.98 in (126.5 mm) 2.53 in (64.5 mm) Fluid Outlet: 3/8 npt(f) 6.05 in ( mm) 6.18 in (157 mm) 8.13 in (206.5 mm) 7.24 in (184 mm) 3/8 npt(f) ir Exhaust (muffler included) 6.3 in (160 mm) 8.12 in (206.5 mm) 1.06 in (2.7 mm) 0.66 in (17 mm) 3.5 in (89 mm) Fluid Inlet: 3/8 npt(f) 5.3 in (134.5 mm) Typical System Drawings Husky 307 Wall-Mount with Siphon Feed Husky 307 Drum-Mount with Siphon Feed ir ontrol Kit Wall Mount racket PN

36 Husky 515 Plastic Pumps ir-operated Double Diaphragm Ordering Information D X X X X X Diaphragm Pump Pump Size Wetted Parts Seats alls/ hecks Diaphragms PUMP SIZE (air motor type and material) WETTED PRTS SETS LLS DIPHRGM 5 = 1/2 center (12.7 mm) or 3/4 ends (19.05) Standard: polypropylene center section 4 = 1/2 center (12.7 mm) or 3/4 ends (19.05) Remote: polypropylene center section * = SP plastic in 1/2 (12.7 mm) pumps 1 = cetal (npt) 2 = cetal 1 = PTFE 1 = PTFE 2 = Poly (npt) 3 = Stainless Steel 3 = Stainless Steel 5 = TPE 5 = PVDF (npt) 9 = Polypropylene 5 = TPE 6 = Santoprene = cetal * (bsp) = PVDF 6 = Santoprene 7 = una N = Poly * (bsp) D = Urethane Duckbill 7 = una N 8 = Fluoroelastomer E = PVDF (bsp) 8 = Fluoroelastomer 0 = Duckbill Popular Models Part Number Part Number (NPT Ported) (SP Ported) Material Standard ir Valve Remote* ir Valve Standard ir Valve Remote* ir Valve Materials for Seats Materials for alls Materials for Diaphragms Fluid Kit ir Kit ir ontrol** cetal D51211 D41211 D5211 D4211 cetal PTFE PTFE D D51255 D41255 D5255 D4255 cetal TPE TPE D D51277 D41277 D5277 D4277 cetal una-n una-n D D51311 D41311 D5311 D4311 Stainless Steel PTFE PTFE D D51331 D41331 D5331 D4331 Stainless Steel Stainless Steel PTFE D D51D05 D41D05 D5D05 D4D05 Duckbill TPE D05D D51D06 D41D06 D5D06 D4D06 Duckbill Santoprene D05D D51D07 D41D07 D5D07 D4D07 Duckbill una-n D05D Polypropylene D52211 D42211 D5211 D4211 cetal PTFE PTFE D D52277 D42277 D5277 D4277 cetal una-n una-n D D52311 D42311 D5311 D4311 Stainless Steel PTFE PTFE D D52331 D42331 D5331 D4331 Stainless Steel Stainless Steel PTFE D D52336 D42336 D5336 D4336 Stainless Steel Stainless Steel Santoprene D D52911 D42911 D5911 D4911 Polypropylene PTFE PTFE D D52955 D42955 D5955 D4955 Polypropylene TPE TPE D D52966 D42966 D5966 D4966 Polypropylene Santoprene Santoprene D D52977 D42977 D5977 D4977 Polypropylene una-n una-n D D52988 D42988 D5988 D4988 Polypropylene Fluoroelastomer Fluoroelastomer D D52D05 D42D05 D5D05 D4D05 Duckbill TPE D05D D52D06 D42D06 D5D06 D4D06 Duckbill Santoprene D05D D52D07 D42D07 D5D07 D4D07 Duckbill una-n D05D PVDF D5511 D4511 D5E11 D4E11 PVDF PTFE PTFE D D5588 D4588 D5E88 D4E88 PVDF Fluoroelastomer Fluoroelastomer D *Required ycleflo or external valve control ** ir control includes air regulator and filter with gauge (see drawing on page 16) 34

37 Husky 515 Plastic Pumps Technical Specifications Husky 515 Plastic Pumps cetal Polypropylene PVDF Maximum fluid working pressure 100 psi (7 bar, 0.7 MPa) 100 psi (7 bar, 0.7 MPa) 100 psi (7 bar, 0.7 MPa) Maximum free flow delivery* 15 gpm (57 lpm) 15 gpm (57 lpm) 15 gpm (57 lpm) Maximum pump speed 400 cpm 400 cpm 400 cpm Displacement per cycle** 0.04 gallon (0.15 liter) 0.04 gallon (0.15 liter) 0.04 gallon (0.15 liter) Maximum suction lift *** 15 ft (4.5 m) dry 15 ft (4.5 m) dry 15 ft (4.5 m) dry Maximum size pumpable solids 0.09 in (2.5 mm) 0.09 in (2.5 mm) 0.09 in (2.5 mm) Maximum ambient operating temperature 180 F (82 ) 150 F (66 ) 180 F (82 ) Maximum diaphragm operating temperature Refer to page 7 Refer to page 7 Refer to page 7 Typical sound level at 70 psi 74 da 74 da 74 da (4.9 bar, 0.49 MPa) 125 cpm Maximum air consumption 28 scfm (0.672 m3/min) 28 scfm (0.672 m3/min) 28 scfm (0.672 m3/min) ir pressure operating range 30 to 100 psi (2.1 to 7 bar, 0.21 to 0.7 MPa) 30 to 100 psi (2.1 to 7 bar, 0.21 to 0.7 MPa) 30 to 100 psi (2.1 to 7 bar, 0.21 to 0.7 MPa) ir inlet size 1/4 npt(f) 1/4 npt(f) 1/4 npt(f) ir exhaust port size 3/8 npt(f) 3/8 npt(f) 3/8 npt(f) Fluid inlet & outlet size**** 1/2 npt(f) or bspt(f) 1/2 npt(f) or bspt(f) 1/2 npt(f) or bspt(f) Weight 7.8 lb (3.5 kg) 6.5 lb (2.9 kg) 8.5 lb (3.9 kg) Wetted parts Groundable cetal, PTFE, SST Polypropylene, PTFE, SST PVDF, PTFE (in addition to ball, seat and diaphragm materials which may vary by pump) Instruction manual * Flow rates are with muffler and do not vary based on diaphragm material. ** Displacement per cycle may vary based on suction condition, discharge head, air pressure and fluid type *** Duckbill suction lift 11 ft (3.3 m) **** Hybrid thread allows for either 1/4 npt or 1/4 bspt fitting ctual pump performance may be affected by prolonged usage at temperature. Performance harts 100 (7, 0.7) Husky 515 Performance 30 (0.84) FLUID OUTLET PRESSURE psi (bar, MPa) 80 (5.5, 0.55) 60 (4.1, 0.41) 40 (2.8, 0.28) 20 (1.4, 0.14) 0 gpm (lpm) 0 4 (15.2) D D 8 (30) 12 (45.42) FLUID FLOW (Pump tested in water with inlet submerged 16 (60.56) 24 (0.67) 18 (0.50) 12 (0.37) 6 (0.17) IR ONSUMPTION scfm (m 3 /min) IR PRESSURE LEGEND = at 100 psi (7 bar, 0.7 MPa) ir onsumption = at 70 psi (4.8 bar, 0.48 MPa) Fluid Pressure = at 40 psi (2.8 bar, 0.28 MPa) D = at 20 psi (1.4 bar, 0.14 MPa) 35

38 Husky 515 Plastic Pumps Dimensions 1/4 npt(f) ir Inlet 4.7 in (119 mm) 1/2 npt(f) or bspt(f) Fluid Outlet 5.01 in (127 mm) 3/4 npt(f) Outlet in (270 mm) 7.75 in (196.9 mm) 9.94 in (252.5 mm) 8.56 in (217.4 mm) 1/2 npt(f) or bspt(f) Fluid Inlet 6.12 in (155.4 mm) 3/4 npt(f) or bspt(f) Fluid Inlet 3/4 npt(f) Inlet Typical System Drawings Husky 515 Wall-Mount with Drum Feed Husky 515 Drum-Mount with Siphon Feed ir ontrol Kit Wall Mount racket PN

39 Husky 716 Metal Pumps ir-operated Double Diaphragm Ordering Information D X X X X X Diaphragm Pump Pump Size Wetted Parts Seats alls/ hecks Diaphragms PUMP SIZE (air motor type and material) WETTED PRTS SETS LLS DIPHRGM 5 = 3/4 (19.05 mm) Standard: polypropylene center section 3 = luminum (npt) 2 = cetal 1 = PTFE 1 = PTFE 4 = 3/4 (19.05 mm) Remote: polypropylene center section 4 = Stainless Steel (npt) 3 = Stainless Steel 3 = Stainless Steel 5 = TPE 9 = Polypropylene 5 = TPE 6 = Santoprene = luminum (bsp) = PVDF 6 = Santoprene 7 = una N D = Stainless Steel (bsp) D = Duckbill 7 = una N 8 = Fluoroelastomer 8 = Fluoroelastomer Popular Models Part Number Part Number (NPT Ported) (SP Ported) Material Standard ir Valve Remote* ir Valve Standard ir Valve Remote* ir Valve Materials for Seats Materials for alls Materials for Diaphragms Fluid Kit ir Kit ir ontrol** luminum D53211 D43211 D5211 D4211 cetal PTFE PTFE D D53255 D43255 D5255 D4255 cetal TPE TPE D D53277 D43277 D5277 D4277 cetal una-n una-n D D53288 D43288 D5288 D4288 cetal Fluoroelastomer Fluoroelastomer D D53311 D43311 D5311 D4311 Stainless Steel PTFE PTFE D D53331 D43331 D5331 D4331 Stainless Steel Stainless Steel PTFE D D53355 D43355 D5355 D4355 Stainless Steel TPE TPE D D53366 D43366 D5366 D4366 Stainless Steel Santoprene Santoprene D D53377 D43377 D5377 D4377 Stainless Steel una-n una-n D D53388 D43388 D5388 D4388 Stainless Steel Fluoroelastomer Fluoroelastomer D D53911 D43911 D5911 D4911 Polypropylene PTFE PTFE D D53955 D43955 D5955 D4955 Polypropylene TPE TPE D D53966 D43966 D5966 D4966 Polypropylene Santoprene Santoprene D D53977 D43977 D5977 D4977 Polypropylene una-n una-n D D53D05 D43D05 D5D05 D4D05 Duckbill TPE D05D D53D06 D43D06 D5D06 D4D06 Duckbill Santoprene D05D D53D07 D43D07 D5D07 D4D07 Duckbill una-n D05D Stainless Steel D54211 D44211 D5D211 D4D211 cetal PTFE PTFE D D54311 D44311 D5D311 D4D311 Stainless Steel PTFE PTFE D D54331 D44331 D5D331 D4D331 Stainless Steel Stainless Steel PTFE D D54335 D44335 D5D335 D4D335 Stainless Steel Stainless Steel TPE D D54336 D44336 D5D336 D4D336 Stainless Steel Stainless Steel Santoprene D D54355 D44355 D5D355 D4D355 Stainless Steel TPE TPE D D54366 D44366 D5D366 D4D366 Stainless Steel Santoprene Santoprene D D54377 D44377 D5D377 D4D377 Stainless Steel una-n una-n D D54388 D44388 D5D388 D4D388 Stainless Steel Fluoroelastomer Fluoroelastomer D D54911 D44911 D5D911 D4D911 Polypropylene PTFE PTFE D D54966 D44966 D5D966 D4D966 Polypropylene Santoprene Santoprene D * Requires ycleflo or external valve control ** ir control includes air regulator and filter with gauge (see drawing on page 19) 37

40 Husky 716 Metal Pumps Technical Specifications Husky 716 Metal Pumps luminum Stainless Steel Maximum fluid working pressure 100 psi (7 bar, 0.7 MPa) 100 psi (7 bar, 0.7 MPa) Maximum free flow delivery* 16 gpm (61 lpm) 16 gpm (61 lpm) Maximum pump speed 400 cpm 400 cpm Displacement per cycle** 0.04 gallon (0.15 liter) 0.04 gallon (0.15 liter) Maximum suction lift 15 ft (4.5 m) dry 15 ft (4.5 m) dry Maximum size pumpable solids 0.09 in (2.5 mm) 0.09 in (2.5 mm) Maximum ambient operating temperature*** 180ºF (82º) 180ºF (82º) Maximum diaphragm operating temperature*** Refer to page 7 Refer to page 7 Typical sound level at 70 psi air 74 da 74 da (4.9 bar, 0.49 MPa) 200 cpm Maximum air consumption 28 scfm (0.672 m3/min) 28 scfm (0.672 m3/min) ir pressure operating range 30 to 100 psi (2.1 to 7 bar, 0.21 to 0.7 MPa) 30 to 100 psi (2.1 to 7 bar, 0.21 to 0.7 MPa) ir inlet size 1/4 npt(f) 1/4 npt(f) ir exhaust port size 3/8 npt(f) 3/8 npt(f) Fluid inlet & outlet size 3/4 npt(f) or bspt(f) 3/4 npt(f) or bspt(f) Weight 8.5 lb (3.9 kg) 18 lb (8.2 kg) Wetted parts (in addition to ball, seat and diaphragm materials which may vary by pump) luminum, Stainless Steel, PTFE, una-n, Santroprene, Zinc-Plated Steel Instruction manual *Flow rates are with muffler and do not vary based on diaphragm material **Displacement per cycle may vary based on suction condition, discharge head, air pressure and fluid type ***ctual pump performance may be affected by prolonged usage at temperature cetal, Polypropylene, Stainless Steel, Polyester, Santoprene, Fluoroelastomer, Nickel-Plated rass, Epoxy-oated Steel Performance harts 100 (7, 0.7) Husky 716 Performance 30 (0.84) FLUID OUTLET PRESSURE psi (bar, MPa) 80 (5.5, 0.55) 60 (4.1, 0.41) 40 (2.8, 0.28) 20 (1.4, 0.14) 0 gpm (lpm) 0 4 (15.2) D D 8 (30) 12 (45.42) FLUID FLOW (Pump tested in water with inlet submerged 16 (60.56) 24 (0.67) 18 (0.50) 12 (0.37) 6 (0.17) IR ONSUMPTION scfm (m 3 /min) IR PRESSURE LEGEND = at 100 psi (7 bar, 0.7 MPa) ir onsumption = at 70 psi (4.8 bar, 0.48 MPa) Fluid Pressure = at 40 psi (2.8 bar, 0.28 MPa) D = at 20 psi (1.4 bar, 0.14 MPa) 38

41 Husky 716 Metal Pumps Dimensions 1/4 npt(f) ir Inlet 4.25 in (108 mm) 3/4 npt(f) or bspt(f) Fluid Outlet 4.44 in (112.8 mm) 3/4 npt(f) Outlet 3/4 npt(f) or bsp(f) Fluid Outlets 2.76 in (62.5 mm) in (264.9 mm) 9.18 in (233.2 mm) 7.37 in (187.2 mm) 7.8 in (198.1 mm) 6.62 in (168.1 mm) 3/4 npt(f) or bspt(f) Fluid Inlets 3/4 npt(f) Inlet 4.29 in (109 mm) 6.04 in (153.4 mm) 3/4 npt(f) or bsp(f) Fluid Inlets Typical System Drawings Husky 716 Wall-Mount with Drum Feed Husky 716 Drum-Mount with Siphon Feed ir ontrol Kit Wall Mount racket PN

42 PRT NO. ONFIGURTION NO. SERIL NO. DTE ODE SERIES MX WPR PSI-bar MDE IN Husky 1050 Plastic Pumps ir-operated Double Diaphragm Husky 1050 Selector Tool To order a Husky 1050, use the online selector tool at or contact your distributor. Pump ID NOTE: Options for seats, check balls, diaphragms, and seals vary for the 1050, 1050F, 1050P, and pump models. Example of Product Selector Tool on Pump onfiguration Options Pump (1 inch ports, 50 gpm) onductive Polypropylene 1050 P Polypropylene 1050 F PVDF 1050,, or : See TEX ertifications below. enter Section and ir Valve Material ir Valve/Monitoring Fluid overs and Manifolds onductive 01 Standard 1 onductive polypropylene, center flange Polypropylene 01 Pulse ount 2 onductive polypropylene, end flange 01 DataTrak 01D Remote P1 Polypropylene, center flange Polypropylene P01 Standard P2 Polypropylene, end flange P01 Pulse ount P01 DataTrak F1 PVDF, center flange P01D Remote F2 PVDF, end flange heck Valve Seats heck Valve alls Diaphragm Manifold O-Rings cetal cetal N una-n None FK FKM Fluoroelastomer N una-n O Polychloroprene Overmolded PT PTFE PP Polypropylene FK FKM Fluoroelastomer FK FKM Fluoroelastomer PV PVDF PT PTFE PO PTFE/EPDM Overmolded SP Santoprene SP Santoprene PT PTFE/EPDM Two-Piece SS 316 Stainless Steel SS 316 Stainless Steel SP Santoprene N una-n TP TPE TP TPE L luminum GE Geolast GE Geolast GE Geolast R Polychloroprene TP TPE W Polychloroprene w/sst ore TEX ertifications ll onductive Polypropylene 1050 pumps are certified: II 2 G c II T4 DataTrak and Pulse ount are certified: II 2 G EEx ia II T3 Nemko 06TEX

43 Husky 1050 Plastic Pumps Popular Models Part Number Material Standard ir Valve Materials for Seats Materials for alls Materials for Diaphragms ir Valve Replacement Kit Seat Kit all Kit Diaphragm Kit Flange Polypropylene Polypropylene Santoprene Santoprene enter Polypropylene PTFE PTFE/EPDM 2 Piece enter Polypropylene PTFE PTFE/EPDM 2 Piece End onductive Polypropylene cetal PTFE PTFE/EPDM 2 Piece End SST PTFE PTFE/EPDM 2 Piece End PVDF SST PTFE PTFE/EPDM 2 Piece End PVDF PTFE PTFE/EPDM 2 Piece End Technical Specifications Husky 1050 Plastic Pumps onductive Polypropylene Polypropylene PVDF Maximum fluid working pressure 125 psi (8.6 bar, 0.86 MPa) 125 psi (8.6 bar, 0.86 MPa) 125 psi (8.6 bar, 0.86 MPa) Maximum free flow delivery 50 gpm (189 lpm) 50 gpm (189 lpm) 50 gpm (189 lpm) Maximum pump speed 280 cpm 280 cpm 280 cpm Displacement per cycle 0.17 gal (0.64 liters) 0.17 gal (0.64 liters) 0.17 gal (0.64 liters) Maximum suction lift 16 ft (4.9 m) dry, 29 ft (8.8 m) wet 16 ft (4.9 m) dry, 29 ft (8.8 m) wet 16 ft (4.9 m) dry, 29 ft (8.8 m) wet Maximum size pumpable solids 1/8 in (3.2 mm) 1/8 in (3.2 mm) 1/8 in (3.2 mm) Sound Power* at 70 psi (4.8 bar, 0.48 MPa) and 50 cpm at 100 psi (7.0 bar, 0.7 MPa) and full flow Sound Pressure** at 70 psi (4.8 bar, 0.48 MPa) and 50 cpm at 100 psi (7.0 bar, 0.7 MPa) and full flow 78 da 90 da 78 da 90 da 78 da 90 da 84 da 96 da 84 da 96 da 84 da 96 da Maximum air consumption 67 scfm 67 scfm 67 scfm ir consumption at 70 psi (4.8 bar, 0.48 MPa), 25 scfm 25 scfm 25 scfm 20 gpm (76 lpm) ir pressure operating range psi ( bar, MPa) psi ( bar, MPa) psi ( bar, MPa) ir inlet size 1/2 npt(f) 1/2 npt(f) 1/2 npt(f) Fluid inlet size 1 in raised face NSI/DIN flange 1 in raised face NSI/DIN flange 1 in raised face NSI/DIN flange Fluid outlet size 1 in raised face NSI/DIN flange 1 in raised face NSI/DIN flange 1 in raised face NSI/DIN flange Weight 18 lb (8.2 kg) 18 lb (8.2 kg) 26 lb (11.8 kg) Wetted parts Non-wetted Parts enter olts polypropylene and material(s) chosen for seat, ball, and diaphragm options polypropylene and material(s) chosen for seat, ball, and diaphragm options polypropylene stainless steel polypropylene stainless steel Instruction manual Repair/parts manual * Sound power measured per ISO ** Sound pressure was tested 3.28 ft (1 m) from equipment. PVDF and material(s) chosen for seat, ball, and diaphragm options polypropylene stainless steel 41

44 10.3 in (262 mm Husky 1050 Plastic Pumps Polypropylene (1050P) and onductive Polypropylene (1050) Performance harts Dimensions FLUID OUTLET PRESSURE psi (bar, MPa) 120 (8.3, 0.83) 100 (7, 0.7) 80 (5.5, 0.55) 60 (4.1, 0.41) 40 (2.8, 0.28) 20 (1.4, 0.14) D Husky 1050 Performance 15.7 in. (399 mm) 3/4 npt(f) air exhaust port 13.2 in. (335 mm) D 60 (1.68) 50 (1.4) 40 (1.12) 30 (0.84) 1 in. NSI/DIN flange IR ONSUMPTION scfm (m 3 /min) 20 (0.56) 17.8 in. 10 (452 mm) 12.0 in. (0.28) (305 mm) enter Flange: 16.0 in. (406 mm) End Flange: 15.2 in. (386 mm) 8.0 in. (203 mm) 1/2 npt(f) air inlet 0 gpm (lpm) 0 5 (19) 10 (38) (57) (76) (95) (114) (133) 2.5 in. FLUID FLOW gpm (lpm) (Pump tested in water with (63.5 inlet mm) submerged) IR PRESSURE LEGEND = at 125 psi (8.3 bar, 0.83 MPa) ir onsumption = at 100 psi (7 bar, 0.7 MPa) Fluid Pressure = at 70 psi (4.8 bar, 0.48 MPa) D = at 40 psi (2.8 bar, 0.28 MPa) 40 (152) 45 (152) 1 in. NSI/DIN flange 3/4 npt(f) air exhaust port 1 in. NSI/DIN flange enter F End Flan Mounting Pattern 5.0" 10.3" 5.6 in. (142 mm) 9.6 in. (244 mm) 3.9 in. (99 mm) 15.7 in. (399 mm) 13.2 in. (335 mm) 2.5 in. (63.5 mm) 17.8 in. (452 mm) 5.0 in. (127 mm) Typical System Drawings 10.3 in. (262 mm) 1 in. NSI/DIN flange Husky 1050 Floor-Mount 5.6 in. (142 mm) 42

45 PRT NO. ONFIGURTION NO. SERIL NO. DTE ODE SERIES MX WPR PSI-bar MDE IN Husky 1050 Metal Pumps ir-operated Double Diaphragm Husky 1050 Selector Tool To order a Husky 1050, use the online selector tool at or contact your distributor. Pump ID NOTE: Options for seats, check balls, diaphragms, and seals vary for the 1050, 1050H, and 1050S pump models. Example of Product Selector Tool on Pump onfiguration Options Pump (1 inch ports, 50 gpm) enter Section and ir Valve Material ir Valve/Monitoring Fluid overs and Manifolds luminum 01 Standard 1 luminum, standard ports, NPT luminum Pulse ount 2 luminum, standard ports, SPT S 01 DataTrak S1 Stainless steel, standard ports, NPT 01D Remote S2 Stainless steel, standard ports, SPT Stainless Steel E Standard H1 Hastelloy, standard ports, NPT H 1 Natural Gas H2 Hastelloy, standard ports, SPT onductive 01 Standard Hastelloy 1050 Polypropylene 01 Pulse ount 01 DataTrak 01D Remote Polypropylene P01 Standard P01 Pulse ount P01 DataTrak P01D Remote,, or : See TEX ertifications below. heck Valve Seats heck Valve alls Diaphragm Manifold O-Rings cetal cetal N una-n None L luminum N una-n O Polychloroprene Overmolded PT PTFE N una-n R Polychloroprene Standard FK FKM Fluoroelastomer FK FKM Fluoroelastomer W Polychloroprene Weighted GE Geolast GE Geolast FK FKM Fluoroelastomer PO PTFE/EPDM Overmolded PP Polypropylene GE Geolast PT PTFE/EPDM Two-Piece SP Santoprene PT PTFE SP Santoprene SS 316 Stainless Steel SP Santoprene TP TPE TP TPE SS 316 Stainless Steel PV PVDF TP TPE TEX ertifications ll luminum 1050 pumps are certified: II 2 G c II T4 Stainless Steel pumps with aluminum or conductive polypropylene centers are certified: II 2 G c II T4 DataTrak and Pulse ount are certified: II 2 G EEx ia II T3 Nemko 06TEX

46 Husky 1050 Metal Pumps Popular Models Part Number Standard Remote Outlet Materials for Materials for Materials for ir Valve Material ir Valve ir Valve Orientation Porting Seats alls Diaphragms Replacement Kit Seat Kit all Kit Diaphragm Kit luminum Multi Port NPT Thermoplastic Polyester cetal Thermoplastic Polyester Elastomer Elastomer Multi Port NPT cetal PTFE PTFE/EPDM 2 Piece Multi Port NPT Geolast Geolast Geolast Multi Port NPT Santoprene Santoprene Santoprene Multi Port NPT 316 SST PTFE PTFE/EPDM 2 Piece Multi Port NPT Polypropylene PTFE PTFE/EPDM 2 Piece Multi Port NPT 316 SST 316 SST PTFE/EPDM 2 Piece * Multi Port NPT una-n una-n una-n * Multi Port SPT una-n una-n una-n * Multi Port NPT FKM FKM FKM * Multi Port SPT FKM FKM FKM Stainless Steel Multi Port NPT 316 SST PTFE PTFE/EPDM 2 Piece Stainless Steel Flange Models ** enter/ Horizontal Flange 316 SST PTFE PTFE ** enter/ Vertical Flange 316 SST PTFE PTFE ** enter/ Horizontal Flange 316 SST Santoprene PTFE ** enter/ Vertical Flange 316 Santoprene PTFE Hastelloy End NPT FKM PTFE PTFE/EPDM 2 Piece *luminum body with Natural Gas operation capabilities. **ll stainless steel flange models have a fixed center inlet. Typical System Drawings Performance harts Husky 1050 Floor-Mount FLUID OUTLET PRESSURE psi (bar, MPa) 120 (8.3, 0.83) 100 (7, 0.7) 80 (5.5, 0.55) 60 (4.1, 0.41) 40 (2.8, 0.28) 20 (1.4, 0.14) D Husky 1050 Performance D 60 (1.68) 50 (1.4) 40 (1.12) 30 (0.84) 20 (0.56) 10 (0.28) IR ONSUMPTION scfm (m 3 /min) 0 gpm (lpm) 0 5 (19) 10 (38) 15 (57) 20 (76) 25 (95) 30 (114) FLUID FLOW gpm (lpm) (Pump tested in water with inlet submerged) 35 (133) 40 (152) 45 (152) IR PRESSURE LEGEND = at 125 psi (8.3 bar, 0.83 MPa) ir onsumption = at 100 psi (7 bar, 0.7 MPa) Fluid Pressure = at 70 psi (4.8 bar, 0.48 MPa) D = at 40 psi (2.8 bar, 0.28 MPa) 44

47 Husky 1050 Metal Pumps Technical Specifications Husky 1050 Metal Pumps luminum Stainless Steel Hastelloy Maximum fluid working pressure 125 psi (8.6 bar, 0.86 MPa) 125 psi (8.6 bar, 0.86 MPa) 125 psi (8.6 bar, 0.86 MPa) Natural gas operated pump models 120 psi (8.3 bar, 0.83 MPa) Maximum free flow delivery Natural gas operated pump models 50 gpm (189 lpm) 49 gpm (185 lpm) 50 gpm (189 lpm) n/a 50 gpm (189 lpm) n/a Maximum pump speed Natural gas operated pump models 280 cpm 275 cpm 280 cpm n/a 280 cpm n/a Displacement per cycle 0.17 gal (0.64 liters) 0.17 gal (0.64 liters) 0.17 gal (0.64 liters) Maximum suction lift 16 ft (4.9 m) dry, 29 ft (8.8 m) wet 16 ft (4.9 m) dry, 29 ft (8.8 m) wet 16 ft (4.9 m) dry, 29 ft (8.8 m) wet Maximum size pumpable solids 1/8 in (3.2 mm) 1/8 in (3.2 mm) 1/8 in (3.2 mm) Sound Power* at 70 psi (4.8 bar, 0.48 MPa) and 50 cpm at 100 psi (7.0 bar, 0.7 MPa) and full flow 78 da 90 da 78 da 90 da 78 da 90 da Sound Pressure** at 70 psi (4.8 bar, 0.48 MPa) and 50 cpm at 100 psi (7.0 bar, 0.7 MPa) and full flow 84 da 96 da 84 da 96 da 84 da 96 da Maximum air consumption Maximum gas consumtion 67 scfm 67 scfm 67 scfm n/a 67 scfm n/a ir consumption at 70 psi (4.8 bar, 0.48 MPa),20 gpm (76 lpm) Natural gas consumption at 70 psi (4.8 bar, 0.48 MPa),20 gpm (76 lpm) 25 scfm 25 scfm 25 scfm n/a 25 scfm n/a ir pressure operating range Gas pressure operating range psi ( bar, MPa) psi ( bar, MPa) 1/2 npt(f) 1/2 npt(f) psi ( bar, MPa) n/a psi ( bar, MPa) n/a ir inlet size Gas inlet size 1/2 npt(f) n/a 1/2 npt(f) n/a Fluid inlet size 1 in npt(f) or 1 in bspt 1 in npt(f) or 1 in bspt 1 in npt(f) or 1 in bspt Fluid outlet size 1 in npt(f) or 1 in bspt 1 in npt(f) or 1 in bspt 1 in npt(f) or 1 in bspt Weight 23 lb (10.5 kg) with conductive 41 lb (18.6 kg) polypropylene center 36.3 lb (16.5 kg) with polypropylene center 37.3 lb (16.9 kg) with aluminum center 41.4 lb (18.8 kg) Wetted parts aluminum and material(s) chosen for seat, ball, and diaphragm options Non-wetted Parts enter olts aluminum coated carbon steel polypropylene stainless steel Instruction manual Natural gas instruction manual n/a Repair/parts manual Natural gas repair/parts manual n/a * Sound power measured per ISO ** Sound pressure was tested 3.28 ft (1 m) from equipment. stainless steel and material(s) chosen for seat, ball, and diaphragm options aluminum stainless steel hastelloy, stainless steel and material(s) chosen for seat, ball, and diaphragm options polypropylene stainless steel n/a n/a Stainless Steel Standard Porting luminum Standard Porting Hastelloy Standard Porting Stainless Steel Forward Flange Stainless Steel Vertical Flange 45

48 Husky 1050 Metal Pumps Dimensions luminum 1 in. npt(f) or 1 in. bspt fluid outlet ports (4) 3/4 npt(f) air exhaust port 7.3 in. (185 mm) 14.7 in. (373 mm) 14.4 in in. (366 mm) (323 mm) 1/2 npt(f) air inlet 15.9 in. (404 mm) 10.9 in. (277 mm) 1.8 in. (46 mm) Mounting Pattern 5.5" 1 in. npt(f) or 1 in. bspt fluid inlet ports (4) 5.0" Stainless Steel and Hastelloy 3/4 npt(f) air exhaust port 1 in. npt(f) or 1 in. bspt fluid outlet ports (4) 13.9 in. (353 mm) 12.9 in. (328 mm) 11.8 in. (300 mm) 13.7 in. (348 mm) 9.5 in. (241 mm) 1/2 npt(f) air inlet 1.1 in. (28 mm) 1 in. npt(f) or 1 in. bspt fluid inlet ports (4) Mounting Pattern 5.5" 5.0" 5.7 in. (145 mm) 9.6 in. (245 mm) in. (102 mm)

49 PRT NO. ONFIGURTION NO. SERIL NO. DTE ODE SERIES MX WPR PSI-bar MDE IN Husky 1050HP Metal Pumps High Pressure ir-operated Diaphragm Husky 1050HP Selector Tool To order a Husky 1050HP, use the online selector tool at or contact your distributor. Pump ID NOTE: Options for seats, check balls, diaphragms, and seals vary for pump models. Example of Product Selector Tool on Pump onfiguration Options Pump enter Section and ir Valve Material ir Valve Manifolds 1050HP luminum luminum 01 Standard 1 2 S1 S2 luminum, Standard Ports, NPT luminum, Standard Ports, SPT Stainless Steel, Standard Ports, NPT Stainless Steel, Standard Ports, SPT heck Valve Seats heck Valve alls Diaphragm Material Manifold O-Rings SS 316 Stainless Steel W Santoprene N Santoprene PT PTFE SP Santoprene GE Geolast O Polychloroprene Overmolded GE Geolast SP Santoprene PT PTFE/Santoprene Two-Piece SS 316 Stainless Steel SP Santoprene 47

50 Husky 1050HP Metal Pumps Popular Models Part No. Seat all Fluid Diaphragm enter Diaphragm Fluid overs Fluid Manifold Porting 24W756 Stainless Steel Santoprene Santoprene Santoprene Stainless Steel luminum NPT 24W757 Stainless Steel Santoprene Santoprene Santoprene Stainless Steel luminum SPT 24W758 Stainless Steel Santoprene Santoprene Santoprene Stainless Steel Stainless Steel NPT 24W759 Stainless Steel Santoprene Santoprene Santoprene Stainless Steel Stainless Steel SPT 24W762 Santoprene Santoprene Santoprene Santoprene Stainless Steel luminum NPT 24W763 Santoprene Santoprene Santoprene Santoprene Stainless Steel luminum SPT 24W764 Geolast Geolast una-n Santoprene Stainless Steel luminum NPT 24W765 Geolast Geolast una-n Santoprene Stainless Steel luminum SPT 24W766 Stainless Steel Weighted Neoprene una-n Santoprene Stainless Steel luminum NPT 24W767 Stainless Steel Weighted Neoprene una-n Santoprene Stainless Steel luminum SPT 24W768 Stainless Steel Weighted Neoprene Neoprene Overmold Santoprene Stainless Steel luminum NPT 24W769 Stainless Steel Weighted Neoprene Neoprene Overmold Santoprene Stainless Steel luminum SPT 24X388 Stainless Steel Stainless Steel 2-piece PTFE/Santoprene Santoprene Stainless Steel Stainless Steel NPT 24X389 Stainless Steel Stainless Steel 2-piece PTFE/Santoprene Santoprene Stainless Steel Stainless Steel SPT Technical Specifications Maximum fluid working pressure psi (14 bar, 1.4 MPa) ir pressure operating range psi ( bar, MPa) Fluid displacement per cycle Low Pressure Setting gal (0.64 l) High Pressure Setting gal (0.76 l) ir consumption at 70 psi (4.8 bar), 20 gpm (76 lpm) Low Pressure Setting...26 scfm (0.7 m3/min) High Pressure Setting...51 scfm (1.4 m3/min) Maximum values with water as media under submerged inlet conditions at ambient temperature: Maximum air consumption Low Pressure Setting...59 scfm (1.7 m3/min) High Pressure Setting...95 scfm (2.7 m3/min) Maximum free-flow delivery Low Pressure Setting gpm (189 lpm) High Pressure Setting gpm (174 lpm) Maximum pump speed Low Pressure Setting cpm High Pressure Setting cpm Maximum suction lift* Dry...16 ft (4.9 m) Wet...29 ft (8.8 m) Maximum size pumpable solids...1/8 in (3.2 mm) Recommended cycle rate for continuous use cpm (in Low or High setting) ir inlet size /4 npt(f) Fluid inlet size....1 in npt(f) or bspt Fluid outlet size....1 in npt(f) or bspt Weight luminum manifolds...48 lb (21.8 kg) SST manifolds lb (27.2 kg) Wetted parts.... aluminum or stainless steel plus the material(s) chosen for seat, ball, and diaphragm options Non-wetted external parts... aluminum, coated carbon steel, sst *Varies based on ball/seat selection and wear, operating speed, material properties, and other variables 48

51 Husky 1050HP Metal Pumps Performance harts Low Pressure Setting 125 (8.6, 0.86) Husky 1050HP Performance pprox. ycles per Minute (2.8) FLUID OUTLET PRESSURE psi (bar, MPa) 100 (7, 0.7) 75 (5.2, 0.52) 50 (3.4, 0.34) 25 (1.7, 0.17) 0 gpm (lpm) E D 0 10 (38) E 20 (76) 30 (114) D 40 (151) 50 (189) 80 (2.3) 60 (1.7) 40 (1.1) 20 (0.6) IR ONSUMPTION scfm (m 3 /min) FLUID FLOW (Pump tested in water with inlet submerged) IR PRESSURE LEGEND = at 125 psi (8.3 bar, 0.83 MPa) ir onsumption = at 100 psi (7 bar, 0.7 MPa) Fluid Pressure = at 70 psi (4.8 bar, 0.48 MPa) D = at 40 psi (2.8 bar, 0.28 MPa) High Pressure Setting Husky 1050HP Performance pprox. ycles per Minute 250 (17, 1.7) (3.5) FLUID OUTLET PRESSURE psi (bar, MPa) 200 (13, 1.3) 150 (10, 1.0) 100 (7, 0.7) 50 (3.4, 0.34) D E E D 100 (2.8) 75 (2.1) 50 (1.4) 25 (0.7) IR ONSUMPTION scfm (m 3 /min) 0 gpm (lpm) 0 10 (38) 20 (76) 30 (114) 40 (151) 50 (189) FLUID FLOW (Pump tested in water with inlet submerged) IR PRESSURE LEGEND = at 125 psi (8.3 bar, 0.83 MPa) ir onsumption = at 100 psi (7 bar, 0.7 MPa) Fluid Pressure = at 70 psi (4.8 bar, 0.48 MPa) D = at 40 psi (2.8 bar, 0.28 MPa) 49

52 Husky 1050HP Metal Pumps Dimensions E Key luminum SST 12.7 in (323 mm) 11.8 in (300 mm) 14.4 in (366 mm) 12.9 in (328 mm) 15.3 in (389 mm) 13.7 in (348 mm) D 10.9 in (277 mm) 9.5 in (241 mm) E 1.8 in (46 mm) 1.1 in (28 mm) F 10.8 in (274 mm) 10.7 in (272 mm) G 21.5 in (546 mm) 20.6 in (523 mm) ll dimensions are approximate 1 in npt(f) or bspt Fluid Outlet 3/4 npt(f) ir Inlet 1 in npt(f) or bspt Fluid Outlet D 1 in npt(f) or bspt Fluid Inlet F G 1 in npt(f) or bspt Fluid Inlet 12.3 in (312.4 mm) 9.4 in (239 mm) 15.6 in (396 mm) 5.0 in (127 mm) 6.2 in (157 mm) 3/4 npt(f) ir Exhaust Port 50

53 PRT NO. ONFIGURTION NO. SERIL NO. DTE ODE SERIES MX WPR PSI-bar MDE IN Husky 1590 Plastic Pumps ir-operated Double Diaphragm Husky 1590 Selector Tool To order a Husky 1590, use the online selector tool at or contact your distributor. Pump ID NOTE: heck the identification plate (ID) for the onfiguration Number of your pump. Use the following matrix to define the components of your pump. Example of Product Selector Tool on Pump onfiguration Options Pump (1.5 inch ports, 90 gpm) P Polypropylene 1590 F PVDF 1590 enter Section and ir Valve Material ir Valve/Monitoring Fluid overs and Manifolds luminum 01 Standard w/una-n Seals F2 PVDF, end flange 01D Remote w/ una-n Seals Stainless Steel S01 Standard P2 Polypropylene, end flange S01D Remote heck Valve Seats heck Valve alls Diaphragm Manifold O-Rings N una-n cetal N una-n None FK Fluoroelastomer N una-n FK Fluoroelastomer PT PTFE GE Geolast FK Fluoroelastomer GE Geolast PP Polypropylene GE Geolast PT PTFE/EPDM Two-Piece PV PVDF PT PTFE PO PTFE Overmolded S 17-4 Stainless Steel SD 440 Stainless Steel SP Santoprene SP Santoprene SP Santoprene TP TPE SS 316 Stainless Steel TP TPE TP TPE 51

54 Husky 1590 Plastic Pumps Ordering Information D X X X X X Diaphragm Pump Pump Size Wetted Parts Seats alls/ hecks Diaphragms PUMP SIZE (air motor type and material) WETTED PRTS SETS LLS DIPHRGM = 1-1/2 (38.1 mm) Standard: aluminum center section 2 = Poly (flange) 3 = Stainless Steel 1 = PTFE 1 = PTFE = 1-1/2 (38.1 mm) Remote: aluminum center section 5 = PVDF (flange) 4 = Hardened SST 2 = cetal 5 = TPE T = 1-1/2 (38.1 mm) Standard: stainless steel center section 5 = TPE 4 = Hardened SST 6 = Santoprene U = 1-1/2 (38.1 mm) Remote: stainless steel center section 6 = Santoprene 5 = TPE 7 = una N 7 = una N 6 = Santoprene 8 = Fluoroelastomer 8 = Fluoroelastomer 7 = una N G = Geolast 9 = Polypropylene 8 = Fluoroelastomer = PVDF G = Geolast G = Geolast Popular Models Part Number Part Number (NSI-Flange) (SP Ported) Material Standard ir Valve Remote* ir Valve Standard ir Valve Remote* ir Valve Materials for Seats Materials for alls Materials for Diaphragms Fluid Kit ir Kit ir ontrol** Standard Pumps with luminum enter Section Polypropylene D2311 Stainless Steel PTFE PTFE D D2377 D2377 Stainless Steel una-n una-n D D2777 D2777 una una-n una-n D D2888 D2888 Fluoroelastomer Fluoroelastomer Fluoroelastomer D D2911 D2911 Polypropylene PTFE PTFE D D2955 Polypropylene TPE TPE D D2966 Polypropylene Santoprene Santoprene D D2977 Polypropylene una-n una-n D D2988 Polypropylene Fluoroelastomer Fluoroelastomer D D29GG D29GG Polypropylene Geolast Geolast D09GG PVDF D5311 Stainless Steel PTFE PTFE D D5666 Santoprene Santoprene Santoprene D D5811 D5911 Fluoroelastomer PTFE PTFE D D5888 D5888 Fluoroelastomer Fluoroelastomer Fluoroelastomer D D511 D511 PVDF PTFE PTFE D D588 PVDF Fluoroelastomer Fluoroelastomer D *Requires ycleflo or external valve control ** ir control includes air regulator and filter with gauge 52

55 Husky 1590 Plastic Pumps Technical Specifications Husky 1590 Plastic Pumps Polypropylene PVDF Maximum fluid working pressure 120 psi (8.4 bar, 0.84 MPa) 120 psi (8.4 bar, 0.84 MPa) Maximum free flow delivery* 100 gpm (378.5 lpm) 100 gpm (378.5 lpm) Maximum pump speed 200 cpm 200 cpm Displacement per cycle** 0.5 gallon (1.96 liter) 0.5 gallon (1.96 liter) Maximum suction lift (D2366) 20 ft (6.1 m) dry 20 ft (6.1 m) dry Maximum size pumpable solids 0.19 in (4.8 mm) 0.19 in (4.8 mm) Maximum operating temperature*** 150 F (65.5 ) 150 F (65.5 ) Maximum diaphragm operating temperature*** PTFE Santoprene una-n TPE Fluoroelastomer Geolast Typical sound level at 70 psi (4.9 bar, 0.49 MPa) 125 cpm 220 F (104.4 ) 180 F (82.2 ) 180 F (82.2 ) 150 F (65.5 ) 250 F (121.1 ) 150 F (65.5 ) 77 da 77 da 220 F (104.4 ) 180 F (82.2 ) 180 F (82.2 ) 150 F (65.5 ) 250 F (121.1 ) 150 F (65.5 ) Maximum air consumption 125 scfm (3.5 m3/min.) 125 scfm (3.5 m3/min.) ir pressure operating range 20 to 120 psi (1.4 to 8.4 bar, 0.14 to 0.84 MPa) 20 to 120 psi (1.4 to 8.4 bar, 0.14 to 0.84 MPa) ir inlet size 1/2 npt(f) 1/2 npt(f) Fluid inlet & outlet size**** 1-1/2 in (38.1 mm) NSI-flange 1-1/2 in (38.1 mm) NSI-flange Weight 35 lb (16 kg) 49 lb (22 kg) Weight with stainless steel center section 48.3 lb (21.9 kg) 62.3 lb (28.2 kg) Instruction manual * Flow rates are with muffler and do not vary based on diaphragm material ** Displacement per cycle may vary based on suction condition, discharge head, air pressure and fluid type *** ctual pump performance may be affected by prolonged usage at temperature 53 53

56 Husky 1590 Plastic Pumps Performance harts Dimensions FLUID OUTLET PRESSURE psi (bar, MPa) 120 (8.4, 0.84) 100 (7, 0.7) 80 (5.5, 0.55) 60 (4.1, 0.41) 40 (2.8, 0.28) 20 (1.4, 0.14) 0 gpm (lpm) 0 D 20 (76) Husky 1590 Performance 40 (152) 60 (227) 80 (303) FLUID FLOW (Pump tested in water with inlet submerged IR PRESSURE LEGEND = at 120 psi (8.4 bar, 0.84 MPa) ir onsumption = at 100 psi (7 bar, 0.7 MPa) Fluid Pressure = at 70 psi (4.8 bar, 0.48 MPa) D = at 40 psi (2.8 bar, 0.28 MPa) D 100 (379) 120 (454) 100 (2.80) 85 (2.38) 70 (1.96) 55 (1.54) 40 (1.12) 25 (0.70) IR ONSUMPTION scfm (m 3 /min) in (304.5 mm) 3/4 npt(f) ir Exhaust (muffler included) 7.55 in ( mm) 1/2 npt(f) ir Inlet 6.0 in (152.5 mm) in (445.5 mm) 10 in (254 mm) Outlet Port ID: 1.75 in (44.5 mm) in (412.5 mm) Flange Diameter: 5.5 in (140 mm) Eight Slots: 0.73 in (18.5 mm) in (552.5 mm) in (489 mm) 3.0 in (76 mm) Inlet Port ID: 1.75 in (44.5 mm) Typical System Drawings 0.25 in (6 mm) 6.0 in (152.5 mm) in (265.5 mm) Husky 1590 bove Ground Gravity Feed 54

57 PRT NO. ONFIGURTION NO. SERIL NO. DTE ODE SERIES MX WPR PSI-bar MDE IN Husky 1590 Metal Pumps ir-operated Double Diaphragm Husky 1590 Selector Tool To order a Husky 1590, use the online selector tool at or contact your distributor. Pump ID NOTE: heck the identification plate (ID) for the onfiguration Number of your pump. Use the following matrix to define the components of your pump. Example of Product Selector Tool on Pump onfiguration Options Pump (1.5 inch ports, 90 gpm) luminum 1590 S Stainless Steel 1590 enter Section and ir Valve Material ir Valve/Monitoring Fluid overs and Manifolds luminum 01 Standard 1 luminum, standard ports, NPT 01D Remote 2 luminum, standard ports, SPT 01E Standard S1 Stainless steel, standard ports, NPT Stainless Steel S01 Standard S2 Stainless steel, standard ports, SPT S01D Remote,, or : See TEX ertifications below. heck Valve Seats heck Valve alls Diaphragm Manifold O-Rings N una-n cetal N una-n None FK Fluoroelastomer N una-n FK Fluoroelastomer PT PTFE GE Geolast FK Fluoroelastomer GE Geolast PP Polypropylene GE Geolast PT PTFE/EPDM Two-Piece PV PVDF PT PTFE SP Santoprene S 17-4 Stainless Steel SD 440 Stainless Steel TP TPE SP Santoprene SP Santoprene SS 316 Stainless Steel TP TPE TP TPE TEX ertifications ll luminum 1590 pumps are certified: II 2 G c II T4 Stainless Steel pumps with aluminum or conductive polypropylene centers are certified: II 2 G c II T4 DataTrak and Pulse ount are certified: II 2 G EEx ia II T3 Nemko 06TEX

58 Husky 1590 Metal Pumps Ordering Information D X X X X X Diaphragm Pump Pump Size Wetted Parts Seats alls/ hecks Diaphragms PUMP SIZE (air motor type and material) WETTED PRTS SETS LLS DIPHRGM = 1-1/2 (38.1 mm) Standard: aluminum center section 3 = luminum (npt) 3 = Stainless Steel 1 = PTFE 1 = PTFE = 1-1/2 (38.1 mm) Remote: aluminum center section 4 = Stainless Steel (npt) 4 = Hardened SST 2 = cetal 5 = TPE T = 1-1/2 (38.1 mm) Standard: stainless steel center section = luminum (bspt) 5 = TPE 4 = Hardened SST 6 = Santoprene U = 1-1/2 (38.1 mm) Remote: stainless steel center section D = Stainless Steel (bspt) 6 = Santoprene 5 = TPE 7 = una-n 7 = una-n 6 = Santoprene 8 = Fluoroelastomer 8 = Fluoroelastomer 7 = una-n G = Geolast 9 = Polypropylene 8 = Fluoroelastomer = PVDF G = Geolast G = Geolast Technical Specifications Husky 1590 Metal Pumps luminum Stainless Steel Maximum fluid working pressure 120 psi (8.4 bar, 0.84 MPa) 120 psi (8.4 bar, 0.84 MPa) Maximum free flow delivery* 100 gpm (378.5 lpm) 100 gpm (378.5 lpm) Maximum pump speed 200 cpm 200 cpm Displacement per cycle** 0.5 gallon (1.96 liter) 0.5 gallon (1.96 liter) Maximum suction lift (D2366) 20 ft (6.1 m) dry 20 ft (6.1 m) dry Maximum size pumpable solids 0.19 in (4.8 mm) 0.19 in (4.8 mm) Maximum operating temperature*** 150 F (65.5 ) 150 F (65.5 ) Maximum diaphragm operating temperature*** PTFE Santoprene una-n TPE Fluoroelastomer Geolast Typical sound level at 70 psi (4.9 bar, 0.49 MPa) 125 cpm 220 F (104.4 ) 180 F (82.2 ) 180 F (82.2 ) 150 F (65.5 ) 250 F (121.1 ) 150 F (65.5 ) 77 da 77 da 220 F (104.4 ) 180 F (82.2 ) 180 F (82.2 ) 150 F (65.5 ) 250 F (121.1 ) 150 F (65.5 ) Maximum air consumption 125 scfm (3.5 m3/min.) 125 scfm (3.5 m3/min.) ir pressure operating range 20 to 120 psi (1.4 to 8.4 bar, 0.14 to 0.84 MPa) 20 to 120 psi (1.4 to 8.4 bar, 0.14 to 0.84 MPa) ir inlet size 1/2 npt(f) 1/2 npt(f) Fluid inlet & outlet size**** 1-1/2 npt(f) or bspt(f) 1-1/2 npt(f) or bspt(f) Weight 33.5 lb (15.2 kg) 86 lb (40 kg) Weight with stainless steel center section n/a 98.8 lb (44.8 kg) Instruction manual *Flow rates are with muffler and do not vary based on diaphragm material **Displacement per cycle may vary based on suction condition, discharge head, air pressure and fluid type *** ctual pump performance may be affected by prolonged usage at temperature 56

59 Husky 1590 Metal Pumps Popular Models Part Number Part Number (NPT Ported) (SP Ported) Material Standard ir Valve Remote* ir Valve Standard ir Valve Remote* ir Valve Seat Material all Material Diaphragm Material Fluid Kit ir Kit ir ontrol** Standard Pumps with luminum enter Section luminum D3311 D3311 D311 D311 Stainless Steel PTFE PTFE D D3341 D341 Hardened SST Stainless Steel PTFE D D3366 D3366 D366 D366 Stainless Steel Santoprene Santoprene D D3377 D3377 D377 D377 Stainless Steel una-n una-n D D3525 D3525 D525 D525 TPE cetal TPE D D3555 D555 TPE TPE TPE D D3666 D3666 D666 D666 Santoprene Santoprene Santoprene D D3777 D3777 D777 D777 una-n una-n una-n D D3888 D3888 D888 D888 Fluoroelastomer Fluoroelastomer Fluoroelastomer D D3GGG D3GGG DGGG DGGG Geolast Geolast Geolast D0GGG D3911 D911 Polypropylene PTFE PTFE D D3977 D977 Polypropylene una-n una-n D Stainless Steel D4311 D4311 DD311 DD311 Stainless Steel PTFE PTFE D D4341 DD341 Stainless Steel Hardened SST PTFE D D4377 D4377 DD377 DD377 Stainless Steel una-n una-n D D4525 DD525 TPE cetal TPE D D4666 D4666 DD666 DD666 Santoprene Santoprene Santoprene D D4777 D4777 DD777 DD777 una-n una-n una-n D D4888 D4888 DD888 DD888 Fluoroelastomer Fluoroelastomer Fluoroelastomer D D4GGG D4GGG DDGGG DDGGG Geolast Geolast Geolast D0GGG D4911 DD911 Polypropylene PTFE PTFE D orrosion Resistant Pumps with Stainless Steel enter Section Stainless Steel DT4311 DU4311 DTD311 DUD311 Stainless Steel PTFE PTFE D DT4377 DU4377 DTD377 DUD377 Stainless Steel una-n una-n D DT4388 DU4388 DTD388 DUD388 Stainless Steel Fluoroelastomer Fluoroelastomer D DT4666 DU4666 DTD666 DUD666 Santoprene Santoprene Santoprene D DT4888 DU4888 DTD888 DUD888 Fluoroelastomer Fluoroelastomer Fluoroelastomer D DT4911 DU4911 DTD911 DUD911 Polypropylene PTFE PTFE D *Requires ycleflo or external valve control ** ir control includes air regulator and filter with gauge Stainless Steel Flange Models* Part Number Outlet Diaphragm Seat Material all Material Orientation Material ir Valve Seat Kit all Kit Diaphgram Kitt Horizontal Stainless Steel PTFE Overmolded PTFE D0300 D Vertical Stainless Steel PTFE Overmolded PTFE D0300 D DR311 Horizontal Stainless Steel PTFE PTFE D0300 D0010 D0001 DP311 Vertical Stainless Steel PTEF PTFE D0300 D0010 D0001 DR366 Horizontal Stainless Steel Santoprene Santoprene D0300 D0060 D0006 DP366 Vertical Stainless Steel Santoprene Santoprene D0300 D0060 D0006 *ll stainless steel flange models have a fixed center inlet. 57

60 Husky 1590 Metal Pumps Performance harts Dimensions FLUID OUTLET PRESSURE psi (bar, MPa) 120 (8.4, 0.84) 100 (7, 0.7) 80 (5.5, 0.55) 60 (4.1, 0.41) 40 (2.8, 0.28) 20 (1.4, 0.14) D Husky 1590 Performance D 100 (2.80) 85 (2.38) 70 (1.96) 55 (1.54) 40 (1.12) 25 (0.70) IR ONSUMPTION scfm (m 3 /min) 10.8 in (273 mm) 1/2 npt(f) ir Inlet 7.75 in (197 mm) 16.8 in (427 mm) 18.3 in (465 mm) 19.6 in (497 mm) 0 gpm (lpm) 0 20 (76) 40 (152) 60 (227) 80 (303) FLUID FLOW (Pump tested in water with inlet submerged IR PRESSURE LEGEND = at 120 psi (8.4 bar, 0.84 MPa) ir onsumption = at 100 psi (7 bar, 0.7 MPa) Fluid Pressure = at 70 psi (4.8 bar, 0.48 MPa) D = at 40 psi (2.8 bar, 0.28 MPa) 100 (379) 120 (454) 3/4 npt(f) ir Exhaust (muffler included) 6.0 in (152.5 mm) 15.9 in (404 mm) 4.8 in (121 mm) Outlet Port ID: 1.5 npt(f) 1.5 in (38 mm) Inlet Port ID: 1.5 npt(f) 0.25 in (6 mm) 6.0 in (152.5 mm) in (265.5 mm) Typical System Drawings Refer to manual for additional dimensions Husky 1590 bove Ground Gravity Feed 58

61 PRT NO. ONFIGURTION NO. SERIL NO. DTE ODE SERIES MX WPR PSI-bar MDE IN Husky Plastic Pumps Husky ir-operated Double Plastic Diaphragm Pumps Husky Selector Tool To order a Husky 15120, use the online selector tool at or contact your distributor. Pump ID NOTE: heck the identification plate (ID) for the onfiguration Number of your pump. Use the following matrix to define the components of your pump. Example of Product Selector Tool on Pump onfiguration Options Pump (1.5 inch ports, 120 gpm) 15120P Polypropylene 15120F PVDF enter Section and ir Valve Material For Use With Fluid overs and Manifolds Polypropylene P01 Standard Diaphragms P1 Polypropylene, enter Flange, NSI/DIN P2 Polypropylene, End Flange, NSI/DIN Polypropylene P01G Overmolded Diaphragms F2 PVDF, End Flange, NSI/DIN Seat Material all Material Diaphragm Material Manifold/Seat Seal Material PP Polypropylene FK FKM FK FKM Fluoroelastomer PT PTFE PV PVDF PT PTFE PO PTFE/EPDM Overmolded SP Santoprene SP Santoprene PT PTFE/Santoprene Two-Piece SS 316 Stainless Steel SP Santoprene 59

62 Husky Plastic Pumps Popular Models Part Number ir Section Fluid Section Porting Seat all Diaphragm ir Valve Replacement Kit Seat Kit all Kit Diaphragm Kit Polypropylene Polypropylene enter Polypropylene PTFE 2-Piece PTFE W225 24W228 24W Polypropylene Polypropylene enter Polypropylene PTFE PTFE OM W225 24W228 24W Polypropylene Polypropylene End Polypropylene PTFE 2-Piece PTFE W225 24W228 24W Polypropylene Polypropylene End Polypropylene PTFE PTFE OM W225 24W228 24W Polypropylene Polypropylene enter Polypropylene Santoprene Santoprene W225 24W229 24W Polypropylene Polypropylene End Polypropylene Santoprene Santoprene W225 24W229 24W Polypropylene Polypropylene enter SST FKM FKM W227 24W230 24W Polypropylene Polypropylene enter SST PTFE 2-Piece PTFE W227 24W228 24W Polypropylene Polypropylene enter SST PTFE PTFE OM W227 24W228 24W Polypropylene Polypropylene End SST FKM FKM W227 24W230 24W Polypropylene Polypropylene End SST PTFE 2-Piece PTFE W227 24W228 24W Polypropylene Polypropylene End SST PTFE PTFE OM W227 24W228 24W Polypropylene Polypropylene enter Santoprene Santoprene Santoprene W226 24W229 24W Polypropylene Polypropylene End Santoprene Santoprene Santoprene W226 24W229 24W Polypropylene PVDF End PVDF FKM FKM W223 24W230 24W Polypropylene PVDF End PVDF PTFE 2-Piece PTFE W223 24W228 24W Polypropylene PVDF End PVDF PTFE PTFE OM W223 24W228 24W217 Technical Specifications Husky Pumps Polypropylene PVDF Maximum fluid working pressure 125 psi (8.6 bar, 0.86 MPa) 125 psi (8.6 bar, 0.86 MPa) Maximum free flow delivery* 120 gpm (454 lpm) 120 gpm (454 lpm) Maximum pump speed 190 cpm 190 cpm Displacement per cycle** 0.63 gallon (2.4 liter) 0.63 gallon (2.4 liter) Maximum suction lift (D2366) 16 ft (4.9 m) dry 16 ft (4.9 m) dry Maximum size pumpable solids 0.25 in (6.3 mm) 0.25 in (6.3 mm) Maximum operating temperature*** 150 F (65.5 ) 225 F (107 ) Maximum diaphragm operating temperature*** PTFE PTFE overmolded diaphragm Santoprene una-n TPE Fluoroelastomer Geolast Typical sound power at 70 psi (4.9 bar, 0.49 MPa) 50 cpm 150 F (65.5 ) 150 F (65.5 ) 150 F (65.5 ) 150 F (65.5 ) 150 F (65.5 ) 150 F (65.5 ) 150 F (65.5 ) 220 F (104.4 ) 180 F (82.2 ) 180 F (82.2 ) 180 F (82.2 ) 150 F (65.5 ) 225 F (107 ) 150 F (65.5 ) 90.9 da 90.9 da Maximum air consumption 85 scfm (2.4 m 3 /min.) 85 scfm (2.4 m 3 /min.) ir pressure operating range 20 to 125 psi (1.4 to 8.6 bar, 0.14 to 0.86 MPa) 20 to 125 psi (1.4 to 8.6 bar, 0.14 to 0.86 MPa) ir inlet size 1/2 npt(f) 1/2 npt(f) Fluid inlet & outlet size 1-1/2 npt(f) or bspt(f) 1-1/2 npt(f) or bspt(f) Weight 57 lb (25.9 kg) 74 lb (33.5 kg) Instruction manual *Flow rates are with muffler and do not vary based on diaphragm material **Displacement per cycle may vary based on suction condition, discharge head, air pressure and fluid type *** ctual pump performance may be affected by prolonged usage at temperature 60

63 Husky Plastic Pumps Dimensions 9.9 in (25.1 mm) 21.0 in (53.3 mm) 23.8 in (60.4 mm) 20.6 in (52.3 mm) 26.8 in (68.1 mm) 17.2 in (43.7 mm) 3.2 in (8.1 mm) 13.8 in (35.1 mm) 7.5 in (19.1 mm) 3.8 in (9.6 mm) 12.4 in (31.5 mm) 61

64 Husky Plastic Pumps Performance harts 1-Piece olt Through Design pprox. ycles per Minute FLUID OUTLET PRESSURE psi (bar, MPa) 120 (8.3, 0.83) 100 (7.0, 0.70) 80 (5.5, 0.55) 60 (4.1, 0.41) 40 (2.8, 0.28) D D 90 (2.5) 75 (2.1) 60 (1.7) 45 (1.3) 30 (0.8) IR ONSUMPTION scfm (m 3 /min) IR PRESSURE LEGEND = at 125 psi (8.3 bar, 0.83 MPa) ir onsumption = at 100 psi (7 bar, 0.7 MPa) Fluid Pressure = at 70 psi (4.8 bar, 0.48 MPa) D = at 40 psi (2.8 bar, 0.28 MPa) 20 (1.4, 0.14) 15 (0.4) 0 gpm (lpm) 0 20 (76) 40 (151) 60 (227) 80 (303) FLUID FLOW (Pump tested in water with inlet submerged) 100 (379) 120 (454) 2-Piece olt Through Design Husky Performance pprox. ycles per Minute FLUID OUTLET PRESSURE psi (bar, MPa) 120 (8.3, 0.83) 100 (7.0, 0.70) 80 (5.5, 0.55) 60 (4.1, 0.41) 40 (2.8, 0.28) D 90 (2.5) IR ONSUMPTION scfm (m 3 /min) 75 (2.1) 60 (1.7) IR PRESSURE = at 125 psi (8.3 bar, 0.83 MPa) LEGEND ir onsumption D 45 (1.3) 30 (0.8) = at 100 psi (7 bar, 0.7 MPa) Fluid Pressure = at 70 psi (4.8 bar, 0.48 MPa) D = at 40 psi (2.8 bar, 0.28 MPa) 20 (1.4, 0.14) 15 (0.4) 0 gpm (lpm) 0 20 (76) 40 (151) 60 (227) 80 (303) FLUID FLOW (Pump tested in water with inlet submerged) 100 (379) 120 (454) Overmolded Design pprox. ycles per Minute FLUID OUTLET PRESSURE psi (bar, MPa) 120 (8.3, 0.83) 100 (7.0, 0.70) 80 (5.5, 0.55) 60 (4.1, 0.41) 40 (2.8, 0.28) D D 90 (2.5) 75 (2.1) 60 (1.7) 45 (1.3) 30 (0.8) IR ONSUMPTION scfm (m 3 /min) IR PRESSURE LEGEND = at 125 psi (8.3 bar, 0.83 MPa) ir onsumption = at 100 psi (7 bar, 0.7 MPa) Fluid Pressure = at 70 psi (4.8 bar, 0.48 MPa) D = at 40 psi (2.8 bar, 0.28 MPa) 20 (1.4, 0.14) 15 (0.4) 0 gpm (lpm) 0 20 (76) 40 (151) 60 (227) 80 (303) FLUID FLOW (Pump tested in water with inlet submerged) 100 (379) 120 (454) 62

65 PRT NO. ONFIGURTION NO. SERIL NO. DTE ODE SERIES MX WPR PSI-bar MDE IN Husky 2150 Plastic Pumps ir-operated Double Diaphragm Husky 2150 Selector Tool To order a Husky 2150, use the online selector tool at or contact your distributor. Pump ID NOTE: heck the identification plate (ID) for the onfiguration Number of your pump. Use the following matrix to define the components of your pump. Example of Product Selector Tool on Pump onfiguration Options Pump (1.5 inch ports, 90 gpm) P Polypropylene 2150 F PVDF 2150 enter Section and ir Valve Material ir Valve/Monitoring Fluid overs and Manifolds luminum 01 Standard w/una-n Seals F2 PVDF, end flange 01D Remote w/ una-n Seals Stainless Steel S01 Standard P2 Polypropylene, end flange S01D Remote heck Valve Seats heck Valve alls Diaphragm Manifold O-Rings N una-n cetal N una-n None FK Fluoroelastomer N una-n FK Fluoroelastomer PT PTFE GE Geolast FK Fluoroelastomer GE Geolast PP Polypropylene GE Geolast PT PTFE/EPDM Two-Piece PV PVDF PT PTFE SP Santoprene S 17-4 Stainless Steel SD 440 Stainless Steel TP TPE SP Santoprene SP Santoprene SS 316 Stainless Steel TP TPE TP TPE 63

66 Husky 2150 Plastic Pumps Ordering Information D X X X X X Diaphragm Pump Pump Size Wetted Parts Seats alls/ hecks Diaphragms PUMP SIZE (air motor type and material) WETTED PRTS SETS LLS DIPHRGM F = 2 (50.8 mm) Standard: aluminum center section 2 = Poly (npt) 3 = Stainless Steel 1 = PTFE 1 = PTFE G = 2 (50.8 mm) Remote: aluminum center section 5 = PVDF (npt) 4 = Hardened SST 2 = cetal 5 = TPE V = 2 (50.8 mm) Standard: stainless steel center section 5 = TPE 4 = Hardened SST 6 = Santoprene 6 = Santoprene 5 = TPE 7 = una-n 7 = una-n 6 = Santoprene 8 = Fluoroelastomer 8 = Fluoroelastomer 7 = una-n G = Geolast 9 = Polypropylene 8 = Fluoroelastomer = PVDF G = Geolast G = Geolast Popular Models Part Number Part Number (NSI-Flange) (SP Ported) Material Standard ir Valve Remote* ir Valve Standard ir Valve Remote* ir Valve Materials for Seats Materials for alls Materials for Diaphragms Fluid Kit ir Kit ir ontrol** Standard Pumps with luminum enter Section Polypropylene DF2311 Stainless Steel PTFE PTFE D0G DF2377 DG2377 Stainless Steel una-n una-n D0G DF2777 DG2777 una una-n una-n D0G DF2888 DG2888 Fluoroelastomer Fluoroelastomer Fluoroelastomer D0G DF2911 DG2911 Polypropylene PTFE PTFE D0G DF2955 Polypropylene TPE TPE D0G DF2966 Polypropylene Santoprene Santoprene D0G DF2977 Polypropylene una-n una-n D0G DF2988 Polypropylene Fluoroelastomer Fluoroelastomer D0G DF29GG DG29GG Polypropylene Geolast Geolast D0G9GG PVDF DF5311 Stainless Steel PTFE PTFE D0G DF5666 Santoprene Santoprene Santoprene D0G DF5811 DG5911 Fluoroelastomer PTFE PTFE D0G DF5888 DG5888 Fluoroelastomer Fluoroelastomer Fluoroelastomer D0G DF511 DG511 PVDF PTFE PTFE D0G DF588 PVDF Fluoroelastomer Fluoroelastomer D0G *Requires ycleflo or external valve control ** ir control includes air regulator and filter with gauge 64

67 Husky 2150 Plastic Pumps Technical Specifications Husky 2150 Plastic Pumps Polypropylene PVDF Maximum fluid working pressure 120 psi (8.4 bar, 0.84 MPa) 120 psi (8.4 bar, 0.84 MPa) Maximum free flow delivery* 150 gpm (568 lpm) 150 gpm (568 lpm) Maximum pump speed 145 cpm 145 cpm Displacement per cycle** 1.03 gallon (3.90 liter) 1.03 gallon (3.90 liter) Maximum suction lift 18 ft (5.48 m) wet or dry 18 ft (5.48 m) wet or dry Maximum size pumpable solids 0.25 in (6.3 mm) 0.25 in (6.3 mm) Maximum operating temperature*** 150 F (65.5 ) 150 F (65.5 ) Maximum diaphragm operating temperature*** PTFE Santoprene una-n TPE Fluoroelastomer Geolast Typical sound level at 70 psi (4.9 bar, 0.49 MPa) 125 cpm 220 F (104.4 ) 180 F (82.2 ) 180 F (82.2 ) 150 F (65.5 ) 250 F (121.1 ) 150 F (65.5 ) 78 da 78 da 220 F (104.4 ) 180 F (82.2 ) 180 F (82.2 ) 150 F (65.5 ) 250 F (121.1 ) 150 F (65.5 ) Maximum air consumption 175 scfm (4.9 m3/min) 175 scfm (4.9 m3/min) ir consumption at 70 psi/60 gpm 60 scfm (1.7 m3/min) 60 scfm (1.7 m3/min) ir pressure operating range 20 to 120 psi (1.4 to 8.4 bar, 0.14 to 0.84 MPa) 20 to 120 psi (1.4 to 8.4 bar, 0.14 to 0.84 MPa) ir inlet size 1/2 npt(f) 1/2 npt(f) Fluid inlet & outlet size**** 2 in (51 mm) NSI-flange 2 in (51 mm) NSI-flange Weight 49 lb (22 kg) 68 lb (30.8 kg) Weight with stainless steel center section 68.5 lb (31 kg) 87.5 lb (39.6 kg) Instruction manual * Flow rates are with muffler and do not vary based on diaphragm material ** Displacement per cycle may vary based on suction condition, discharge head, air pressure and fluid type *** ctual pump performance may be affected by prolonged usage at temperature 65

68 Husky 2150 Plastic Pumps Performance harts Dimensions FLUID OUTLET PRESSURE psi (bar, MPa) 120 (8.4, 0.84) 100 (7, 0.7) 80 (5.5, 0.55) 60 (4.1, 0.41) 40 (2.8, 0.28) 20 (1.4, 0.14) D Husky 2150 Performance D 150 (4.2) 125 (3.5) 100 (2.8) 75 (2.1) 50 (1.4) 25 (0.7) IR ONSUMPTION scfm (m 3 /min) 13.7 in (348 mm) 8.74 in (221.9 mm) 1/2 npt(f) ir Inlet 11 in (280.5 mm) in (489 mm) in (654 mm) in (578 mm) 0 gpm (lpm) 0 20 (76) 40 (152) 60 (227) 80 (303) 100 (379) 120 (454) FLUID FLOW (Pump tested in water with inlet submerged 140 (531) 160 (606) 3/4 npt(f) ir Exhaust (muffler included) 6.0 in (152.5 mm) in (501.5 mm) 3.5 in (89 mm) IR PRESSURE LEGEND = at 120 psi (8.4 bar, 0.84 MPa) ir onsumption = at 100 psi (7 bar, 0.7 MPa) Fluid Pressure = at 70 psi (4.8 bar, 0.48 MPa) D = at 40 psi (2.8 bar, 0.28 MPa) Port Diameter: 2.2 in (56 mm) Flange Diameter: 6 in (152.5 mm) Eight Slots: 0.75 in (19 mm) 0.5 in (13 mm) Typical System Drawings 6.0 in (152.5 mm) 12.5 in (317.5 mm) Husky 2150 bove Ground Gravity Feed 66

69 PRT NO. ONFIGURTION NO. SERIL NO. DTE ODE SERIES MX WPR PSI-bar MDE IN Husky 2150 Metal Pumps ir-operated Double Diaphragm Husky 2150 Selector Tool To order a Husky 2150, use the online selector tool at or contact your distributor. Pump ID NOTE: heck the identification plate (ID) for the onfiguration Number of your pump. Use the following matrix to define the components of your pump. Example of Product Selector Tool on Pump onfiguration Options Pump (2.0 inch ports, 150 gpm) luminum 2150 S Stainless Steel 2150 enter Section and ir Valve Material ir Valve/Monitoring Fluid overs and Manifolds luminum 01 Standard 1 luminum, standard ports, NPT 01D Remote 2 luminum, standard ports, SPT Stainless Steel S01 Standard S1 Stainless steel, standard ports, NPT S01D Remote S2 Stainless steel, standard ports, SPT,, or : See TEX ertifications below. heck Valve Seats heck Valve alls Diaphragm Manifold O-Rings N una-n cetal N una-n None FK Fluoroelastomer N una-n FK Fluoroelastomer PT PTFE GE Geolast FK Fluoroelastomer GE Geolast PP Polypropylene GE Geolast PO PTFE Overmolded PV PVDF PT PTFE PT PTFE/EPDM Two-Piece S 17-4 Stainless Steel SD 440 Stainless Steel SP Santoprene SP Santoprene SP Santoprene TP TPE SS 316 Stainless Steel TP TPE TP TPE TEX ertifications ll luminum 2150 pumps are certified: II 2 G c II T4 Stainless Steel pumps with aluminum or conductive polypropylene centers are certified: II 2 G c II T4 DataTrak and Pulse ount are certified: II 2 G EEx ia II T3 Nemko 06TEX

70 Husky 2150 Metal Pumps Ordering Information D X X X X X Diaphragm Pump Pump Size Wetted Parts Seats alls/ hecks Diaphragms PUMP SIZE (air motor type and material) WETTED PRTS SETS LLS DIPHRGM F = 2 (50.8 mm) Standard: aluminum center section 3 = luminum (npt) 3 = Stainless Steel 1 = PTFE 1 = PTFE G = 2 (50.8 mm) Remote: aluminum center section 4 = Stainless Steel (npt) 4 = Hardened SST 2 = cetal 5 = TPE V = 2 (50.8 mm) Standard: stainless steel center section 6 = Ductile Iron (npt) 5 = TPE 4 = Hardened SST 6 = Santoprene = luminum (bspt) 6 = Santoprene 5 = TPE 7 = una-n D = Stainless Steel (bspt) 7 = una-n 6 = Santoprene 8 = Fluoroelastomer F = Ductile Iron (bspt) 8 = Fluoroelastomer 7 = una-n G = Geolast 9 = Polypropylene 8 = Fluoroelastomer H = 2 npt lum Extended = PVDF G = Geolast G = 2 bsp lum Extended G = Geolast Technical Specifications Husky 2150 Metal Pumps luminum Stainless Steel Ductile Iron Maximum fluid working pressure 120 psi (8.4 bar, 0.84 MPa) 120 psi (8.4 bar, 0.84 MPa) 120 psi (8.4 bar, 0.84 MPa) Maximum free flow delivery* 150 gpm (568 lpm) 150 gpm (568 lpm) 150 gpm (568 lpm) Maximum pump speed 145 cpm 145 cpm 145 cpm Displacement per cycle** 1.03 gallon (3.90 liter) 1.03 gallon (3.90 liter) 1.03 gallon (3.90 liter) Maximum suction lift (DF3666) 20 ft (6.1 m) dry 20 ft (6.1 m) dry 20 ft (6.1 m) dry Maximum size pumpable solids 0.25 in (6.3 mm) 0.25 in (6.3 mm) 0.25 in (6.3 mm) Maximum operating temperature*** 150 F (65.5 ) 150 F (65.5 ) 150 F (65.5 ) Maximum diaphragm operating temperature*** PTFE Santoprene una-n TPE Fluoroelastomer Geolast Typical sound level at 70 psi (4.9 bar, 0.49 MPa) 125 cpm 220 F (104.4 ) 180 F (82.2 ) 180 F (82.2 ) 150 F (65.5 ) 250 F (121.1 ) 150 F (65.5 ) 220 F (104.4 ) 180 F (82.2 ) 180 F (82.2 ) 150 F (65.5 ) 250 F (121.1 ) 150 F (65.5 ) 78 da 78 da 78 da 220 F (104.4 ) 180 F (82.2 ) 180 F (82.2 ) 150 F (65.5 ) 250 F (121.1 ) 150 F (65.5 ) Maximum air consumption 175 scfm (4.9 m3/min) 175 scfm (4.9 m3/min) 175 scfm (4.9 m3/min) ir pressure operating range 20 to 120 psi (1.4 to 8.4 bar, 0.14 to 0.84 MPa) 20 to 120 psi (1.4 to 8.4 bar, 0.14 to 0.84 MPa) 20 to 120 psi (1.4 to 8.4 bar, 0.14 to 0.84 MPa) ir inlet size 1/2 npt(f) 1/2 npt(f) 1/2 npt(f) Fluid inlet & outlet size**** 2 in (51 mm) npt(f) 2 in (51 mm) npt(f) 2 in (51 mm) npt(f) Weight 58 lb (26.3 kg) 111 lb (50 kg) 130 lb (59 kg) 62 lb (28.1 kg) - Extended Weight with stainless steel center section n/a 134 lb (60 kg) n/a Instruction manual * Flow rates are with muffler and do not vary based on diaphragm material ** Displacement per cycle may vary based on suction condition, discharge head, air pressure and fluid type *** ctual pump performance may be affected by prolonged usage at temperature 68

71 Husky 2150 Metal Pumps Popular Models Part Number Part Number (NPT Ported) (SP Ported) Material Standard ir Valve Remote* ir Valve Standard ir Valve Remote* ir Valve Seat Material all Material Diaphragm Material Fluid Kit ir Kit ir ontrol** Standard Pumps with luminum enter Section luminum*** DF3311 DG3311 DF311 DG311 Stainless Steel PTFE PTFE D0F DF3341 DG3341 DF341 DG341 Stainless Steel Hardened SST PTFE D0F DF3366 DG3366 DF366 DG366 Stainless Steel Santoprene Santoprene D0F DF3377 DG3377 DF377 DG377 Stainless Steel una-n una-n D0F DF3525 DG3525 DF525 DG525 TPE cetal TPE D0F DF3555 DF555 TPE TPE TPE D0F DF3666 DG3666 DF666 DG666 Santoprene Santoprene Santoprene D0F DF3777 DG3777 DF777 DG777 una-n una-n una-n D0F DF3888 DG3888 DF888 DG888 Fluoroelastomer Fluoroelastomer Fluoroelastomer D0F DF3GGG DG3GGG DFGGG DGGGG Geolast Geolast Geolast D0FGGG DF3911 DG3911 DF911 DG911 Polypropylene PTFE PTFE D0F DF3977 DG3977 DF977 Polypropylene una-n una-n D0F Stainless Steel DF4311 DG4311 DFD311 DGD311 Stainless Steel PTFE PTFE D0F DF4341 DFD341 Stainless Steel Hardened SST PTFE D0F DF4366 DG4366 DFD366 DGD366 Stainless Steel Santoprene Santoprene D0F DF4377 DG4377 DFD377 DGD377 Stainless Steel una-n una-n D0F DF4525 DFD525 TPE cetal TPE D0F DF4666 DG4666 DFD666 DGD666 Santoprene Santoprene Santoprene D0F DF4777 DG4777 DFD777 DGD777 una-n una-n una-n D0F DF4888 DG4888 DFD888 DGD888 Fluoroelastomer Fluoroelastomer Fluoroelastomer D0F DF4GGG DG4GGG DFDGGG DGDGGG Geolast Geolast Geolast D0FGGG DF4911 DFD911 Polypropylene PTFE PTFE D0F Ductile DF6311 DFF311 Stainless Steel PTFE PTFE D0F DF6366 DFF366 Stainless Steel Santoprene Santoprene D0F DF6441 DFF441 Hardened SST Hardened SST PTFE D0F DF6466 DG6466 DFF466 DGF466 Hardened SST Santoprene Santoprene D0F DF6525 DFF525 TPE cetal TPE D0F DF6666 DG6666 DFF666 DGF666 Santoprene Santoprene Santoprene D0F DF611 DFF11 PVDF PTFE PTFE D0F DF688 DFF88 PVDF Fluoroelastomer Fluoroelastomer D0F DF6GGG DG6GGG DFFGGG DGFGGG Geolast Geolast Geolast D0FGGG orrosion Resistant Pumps with Stainless Steel enter Section Stainless Steel DV4311 DVD311 Stainless Steel PTFE PTFE D0F DV4377 DVD377 Stainless Steel una-n una-n D0F DV4388 DVD388 Stainless Steel Fluoroelastomer Fluoroelastomer D0F DV4666 DVD666 Santoprene Santoprene Santoprene D0F DV4888 DVD888 Fluoroelastomer Fluoroelastomer Fluoroelastomer D0F DV4911 DVD911 Polypropylene PTFE PTFE D0F *Requires ycleflo or external valve control. ** ir control includes air regulator and filter with gauge. *** lso available in Extended Height version; use DFH or DFG designations Stainless Steel Flange Models* Part Number Outlet Diaphragm Seat Material all Material Orientation Material ir Valve Seat Kit all Kit Diaphgram Kit Horizontal Stainless Steel PTFE Overmolded PTFE D0F300 D0F Vertical Stainless Steel PTFE Overmolded PTFE D0F300 D0F DFR311 Horizontal Stainless Steel PTFE PTFE D0F300 D0F010 D0F001 DFP311 Vertical Stainless Steel PTFE PTFE D0F300 D0F010 D0F001 DFR366 Horizontal Stainless Steel Santoprene Santoprene D0F300 D0F060 D0F006 DFP366 Vertical Stainless Steel Santoprene Santoprene D0F300 D0F060 D0F006 *ll stainless steel flange models have a fixed center inlet. 69

72 Husky 2150 Metal Pumps Performance harts Dimensions FLUID OUTLET PRESSURE psi (bar, MPa) 120 (8.4, 0.84) 100 (7, 0.7) 80 (5.5, 0.55) 60 (4.1, 0.41) 40 (2.8, 0.28) 20 (1.4, 0.14) D Husky 2150 Performance D 150 (4.2) 125 (3.5) 100 (2.8) 75 (2.1) 50 (1.4) 25 (0.7) IR ONSUMPTION scfm (m 3 /min) 12.3 in (312.5 mm) 8.39 in (213 mm) 1/2 npt(f) ir Inlet 9.06 in (230 mm) in (492 mm) in (543 mm) 23.0 in (584 mm) 0 gpm (lpm) 0 20 (76) 40 (152) 60 (227) 80 (303) 100 (379) 120 (454) FLUID FLOW (Pump tested in water with inlet submerged 140 (531) 160 (606) 3/4 npt(f) ir Exhaust (muffler included) 6.0 in (152.5 mm) in (443 mm) 2.0 in (51 mm) IR PRESSURE LEGEND = at 120 psi (8.4 bar, 0.84 MPa) ir onsumption = at 100 psi (7 bar, 0.7 MPa) Fluid Pressure = at 70 psi (4.8 bar, 0.48 MPa) D = at 40 psi (2.8 bar, 0.28 MPa) 6.25 in (159 mm) Port Diameter: 2 in (51 mm) 0.38 in (9.5 mm) 6.0 in (152.5 mm) 12.5 in (317.5 mm) Typical System Drawings Husky 2150 bove Ground Gravity Feed 70

73 PRT NO. ONFIGURTION NO. SERIL NO. DTE ODE SERIES MX WPR PSI-bar MDE IN Husky 2200 Plastic Pumps Husky ir-operated Double Plastic Diaphragm Pumps Husky 2200 Selector Tool To order a Husky 2200, use the online selector tool at or contact your distributor. Pump ID NOTE: heck the identification plate (ID) for the onfiguration Number of your pump. Use the following matrix to define the components of your pump. Example of Product Selector Tool on Pump onfiguration Options Pump (2 inch ports, 200 gpm) 2200P Polypropylene 2200F PVDF enter Section and ir Valve Material For Use With Fluid overs and Manifolds Polypropylene P01 Standard Diaphragms P1 Polypropylene, enter Flange, NSI/DIN P2 Polypropylene, End Flange, NSI/DIN Polypropylene P01G Overmolded Diaphragms F2 PVDF, End Flange, NSI/DIN Seat Material all Material Diaphragm Material Manifold/Seat Seal Material PP Polypropylene FK FKM FK FKM Fluoroelastomer PT PTFE PV PVDF PT PTFE PO PTFE/EPDM Overmolded SP Santoprene SP Santoprene PT PTFE/Santoprene Two-Piece SS 316 Stainless Steel SP Santoprene 71

74 Husky 2200 Plastic Pumps Popular Models Part Number ir Section Fluid Section Porting Seat all Diaphragm ir Valve Replacement Kit Seat Kit all Kit Diaphragm Kit Polypropylene Polypropylene enter Polypropylene PTFE 2-Piece PTFE 24V231 24V248 24V251 24V Polypropylene Polypropylene enter Polypropylene PTFE PTFE OM 24V231 24V248 24V251 24V Polypropylene Polypropylene End Polypropylene PTFE 2-Piece PTFE 24V231 24V248 24V251 24V Polypropylene Polypropylene End Polypropylene PTFE PTFE OM 24V231 24V248 24V251 24V Polypropylene Polypropylene enter Polypropylene Santoprene Santoprene 24V231 24V248 24V252 24V Polypropylene Polypropylene End Polypropylene Santoprene Santoprene 24V231 24V248 24V252 24V Polypropylene Polypropylene enter SST FKM FKM 24V231 24V250 24V253 24V Polypropylene Polypropylene enter SST PTFE 2-Piece PTFE 24V231 24V250 24V251 24V Polypropylene Polypropylene enter SST PTFE PTFE OM 24V231 24V250 24V251 24V Polypropylene Polypropylene End SST FKM FKM 24V231 24V250 24V253 24V Polypropylene Polypropylene End SST PTFE 2-Piece PTFE 24V231 24V250 24V251 24V Polypropylene Polypropylene End SST PTFE PTFE OM 24V231 24V250 24V251 24V Polypropylene Polypropylene enter Santoprene Santoprene Santoprene 24V231 24V249 24V252 24V Polypropylene Polypropylene End Santoprene Santoprene Santoprene 24V231 24V249 24V252 24V Polypropylene PVDF End PVDF FKM FKM 24V231 24V247 24V253 24V Polypropylene PVDF End PVDF PTFE 2-Piece PTFE 24V231 24V247 24V251 24V Polypropylene PVDF End PVDF PTFE PTFE OM 24V231 24V247 24V251 24V241 Technical Specifications 72 Husky 2200 Pumps Polypropylene PVDF Maximum fluid working pressure 125 psi (8.6 bar, 0.86 MPa) 125 psi (8.6 bar, 0.86 MPa) Maximum free flow delivery* 200 gpm (757 lpm) 200 gpm (757 lpm) Maximum pump speed Standard diaphragm Overmolded diaphragm Displacement per cycle** Standard diaphragm Overmolded diaphragm 125 cpm 155 cpm 125 cpm 155 cpm 1.6 gallon (6.1 liter) 1.3 gallons (4.9 liter) 1.6 gallon (6.1 liter) 1.3 gallons (4.9 liter) Maximum suction lift (D2366) 16 ft (4.9 m) dry 16 ft (4.9 m) dry Maximum size pumpable solids 0.25 in (6.3 mm) 0.25 in (6.3 mm) Maximum operating temperature*** 150 F (65.5 ) 225 F (107 ) Maximum diaphragm operating temperature*** PTFE PTFE overmolded diaphragm Santoprene una-n TPE Fluoroelastomer Geolast Typical sound power at 70 psi (4.9 bar, 0.49 MPa) 50 cpm Maximum air consumption Standard diaphragm Overmolded diaphragm ir pressure operating range 150 F (65.5 ) 150 F (65.5 ) 150 F (65.5 ) 150 F (65.5 ) 150 F (65.5 ) 150 F (65.5 ) 150 F (65.5 ) 220 F (104.4 ) 180 F (82.2 ) 180 F (82.2 ) 180 F (82.2 ) 150 F (65.5 ) 225 F (107 ) 150 F (65.5 ) 95.2 da 90.9 da 140 scfm (4.0 m 3 /min.) 157 scfm (4.4 m 3 /min.) 20 to 125 psi (1.4 to 8.6 bar, 0.14 to 0.86 MPa) 140 scfm (4.0 m 3 /min.) 157 scfm (4.4 m 3 /min.) 20 to 125 psi (1.4 to 8.6 bar, 0.14 to 0.86 MPa) ir inlet size 3/4 npt(f) 3/4 npt(f) Fluid inlet & outlet size 2 npt(f) or bspt(f) 2 npt(f) or bspt(f) Weight 80 lb (36.3 kg) 106 lb (48.1 kg) Instruction manual *Flow rates are with muffler and do not vary based on diaphragm material **Displacement per cycle may vary based on suction condition, discharge head, air pressure and fluid type *** ctual pump performance may be affected by prolonged usage at temperature

75 Husky 2200 Plastic Pumps Dimensions enter Flange End Flange 24.1 in (61.2 mm) 25.1 in (63.8 mm) 27.2 in (69.1 mm) 30.3 in (77.0 mm) 28.7 in (72.9 mm) 31.7 in (80.5 mm) 3.1 in (7.9 mm) 3.6 in (9.1 mm) 12.8 in (32.5 mm) 26.3 in (66.8 mm) 12.0 in (30.5 mm) 25.6 in (65.0 mm) 18.5 in (47.0 mm) 19.8 in (50.3 mm) 16.3 in (41.4 mm) 16.3 in (41.4 mm) 7.0 in (17.8 mm) 7.0 in (17.8 mm) 8.2 in (20.8 mm) 13.9 in (35.3 mm) 8.2 in (20.8 mm) 13.9 in (35.3 mm) 73

76 Husky 2200 Plastic Pumps Performance harts olt Through Design 125 (8.6, 0.86) Husky 2200 Performance pprox. ycles per Minute (5.0) FLUID OUTLET PRESSURE psi (bar, MPa) 100 (7, 0.69) 75 (5.2, 0.52) 50 (3.4, 0.34) 25 (1.7, 0.17) D D 140 (4.0) 105 (3.0) 70 (2.0) 35 (1.0) IR ONSUMPTION scfm (m 3 /min) 0 gpm (lpm) 0 40 (151) 80 (303) 120 (454) 160 (606) 200 (757) FLUID FLOW (Pump tested in water with inlet submerged) IR PRESSURE LEGEND = at 125 psi (8.3 bar, 0.83 MPa) ir onsumption = at 100 psi (7 bar, 0.7 MPa) Fluid Pressure = at 70 psi (4.8 bar, 0.48 MPa) D = at 40 psi (2.8 bar, 0.28 MPa) Overmolded Design 125 (8.6, 0.86) Husky 2200 Performance pprox. ycles per Minute (5.0) FLUID OUTLET PRESSURE psi (bar, MPa) 100 (7, 0.69) 75 (5.2, 0.52) 50 (3.4, 0.34) 25 (1.7, 0.17) D D 140 (4.0) 105 (3.0) 70 (2.0) 35 (1.0) IR ONSUMPTION scfm (m 3 /min) 0 gpm (lpm) 0 40 (151) 80 (303) 120 (454) 160 (606) 200 (757) FLUID FLOW (Pump tested in water with inlet submerged) IR PRESSURE LEGEND = at 125 psi (8.3 bar, 0.83 MPa) ir onsumption = at 100 psi (7 bar, 0.7 MPa) Fluid Pressure = at 70 psi (4.8 bar, 0.48 MPa) D = at 40 psi (2.8 bar, 0.28 MPa) 74

77 Husky 3300 Plastic Pumps ir-operated Double Diaphragm Husky 3300 Selector Tool To order a Husky 3300, use the online selector tool at or contact your distributor. Pump onfiguration Number NOTE: Options for seats, check balls, diaphragms, and seals vary. Pump onfiguration Options Example of Product Selector Tool on Pump (3 inch ports, 300 gpm) P Polypropylene 3300 : See TEX ertifications below. enter Section and ir Valve Material ir Valve/Monitoring Fluid overs and Manifolds luminum 01 Standard Diaphragms P1 Polypropylene, center flange 01G Overmolded Diaphragms Polypropylene P01 Standard Diaphragms P01G Overmolded Diaphragms heck Valve Seats heck Valve alls Diaphragm Manifold and Seat Seals cetal cetal N una-n --- Models with una-n, L luminum N una-n O Polychloroprene Overmolded FKM Fluoroelastomer or TPE seats do not use N una-n R Polychloroprene Standard R Polychloroprene o-rings. FK FKM Fluoroelastomer W Polychloroprene Weighted FK FKM Fluoroelastomer N una-n GE Geolast FK FKM Fluoroelastomer GE Geolast PT PTFE PP Polypropylene GE Geolast PO PTFE/EPDM Overmolded SP Santoprene PT PTFE PT PTFE/Santoprene Two-Piece SS 316 Stainless Steel SP Santoprene SP Santoprene TP TPE TP TPE TP TPE TEX ertifications Pumps with polypropylene fluid or center sections are not TEX certified. 75

78 Husky 3300 Plastic Pumps Popular Models Material Part Number Materials for Seats Materials for alls Materials for Diaphragms ir Valve Replacement Kit Seat Kit all Kit Diaphragm Kit O-Ring Kit Polypropylene Polypropylene PTFE 2 pc PTFE 24K857 24K933 24K943 24K905 24K927 Polypropylene Polypropylene Santoprene Santoprene 24K857 24K933 24K944 24K902 24K927 Polypropylene Santoprene Santoprene Santoprene 24K857 24K934 24K944 24K902 24K927 Polypropylene Stainless Steel PTFE 2 pc PTFE 24K857 24K935 24K943 24K905 24K927 Polypropylene Polypropylene FKM FKM 24K857 24K933 24K945 24K903 24K927 Technical Specifications Husky 3300 Plastic Pumps Maximum fluid working pressure Maximum free flow delivery* Standard diaphragms at 100 psi (7.0 bar, 0.7 MPa) Overmolded diaphragms at 100 psi (7.0 bar, 0.7 MPa) Maximum pump speed* Standard diaphragms at 100 psi (7.0 bar, 0.7 MPa) Overmolded diaphragms at 100 psi (7.0 bar, 0.7 MPa) Maximum suction lift * (varies widely based on ball/seat selection and wear, operating speed, material properties, and other variables) Maximum size pumpable solids Noise (da)*** Sound Power at 50 psi (3.4 bar) and 50 cpm Sound Power at 120 psi (8.3 bar) and full flow Sound Pressure at 50 psi (3.4 bar) and 50 cpm Sound Pressure at 120 psi (8.3 bar) and full flow Maximum air consumption ir pressure operating range ir inlet size Fluid inlet/outlet Weight Instruction manual Repair/parts manual Polypropylene 100 psi (7.0 bar, 0.7 MPa) 280 gpm (1,059 lpm) 260 gpm (984 lpm) 97 cpm 130 cpm 8 ft (2.4 m) dry 0.5 in (13 mm) 92 da 99 da 86 da 93 da 275 scfm (7.8 m 3 /min.) 20 to 100 psi (1.4 to 7.0 bar, 0.14 to 0.7 MPa) 3/4 npt(f) 3 in (76.2 mm) NSI/DIN flange 200 lb (91 kg) * Maximum values with water as media at ambient temperature. Water level is approximately 3 feet above pump inlet. ** Startup pressures and displacement per cycle may vary based on suction condition, discharge head, air pressure, and fluid type. *** Sound power measured per ISO Sound pressure was tested 3.28 ft (1 m) from equipment. *** ctual pump performance may be affected by prolonged usage at temperature 76

79 Husky 3300 Plastic Pumps Performance harts Dimensions FLUID OUTLET PRESSURE psi (bar, MPa) 125 (8.6, 0.86) 100 (7, 0.69) 75 (5.2, 0.52) 50 (3.4, 0.34) 25 (1.7, 0.17) D Husky 3300 Performance pprox. ycles per Minute D 375 (10.6) 300 (8.5) 225 (6.4) 150 (4.2) 75 (2.1) IR ONSUMPTION scfm (m 3 /min) ir Inlet (opposite side from muffler) in. (37.0 cm) in. (74.0 cm) gpm (lpm) (189) 100 (379) 150 (568) 200 (757) 250 (946) FLUID FLOW (Pump tested in water with inlet submerged) 300 (1136) in. (67.8 cm) IR PRESSURE LEGEND = at 125 psi (8.3 bar, 0.83 MPa) ir onsumption = at 100 psi (7 bar, 0.7 MPa) Fluid Pressure = at 70 psi (4.8 bar, 0.48 MPa) D = at 40 psi (2.8 bar, 0.28 MPa) in. (33.0 cm) in. (49.0 cm) 8.30 in. (21.1 cm) in in. (42.1 cm) (43.1 cm) Typical System Drawings D G 77

80 Husky 3300 Metal Pumps ir-operated Double Diaphragm Husky 3300 Selector Tool To order a Husky 3300, use the online selector tool at or contact your distributor. Pump onfiguration Number NOTE: Options for seats, check balls, diaphragms, and seals vary. Pump onfigurations Example of Product Selector Tool on Pump (3 inch ports, 300 gpm) enter Section and ir Valve Material ir Valve/Monitoring Fluid overs and Manifolds luminum 01 Standard Diaphragms 1 luminum, center flange, npt luminum 3300 Optional FKM seals with 2 luminum, center flange, bspt 01E Standard Diaphragms S 01G Overmolded Diaphragms S1 Stainless steel, center flange, npt Stainless Steel 3300 Polypropylene P01 Standard Diaphragms S2 Stainless steel, center flange, bspt P01G Overmolded Diaphragms : See TEX ertifications below. heck Valve Seats heck Valve alls Diaphragm Manifold and Seat Seals cetal cetal N una-n --- Models with una-n, L luminum N una-n O Polychloroprene Overmolded FKM Fluoroelastomer or TPE seats do not use N una-n R Polychloroprene Standard R Polychloroprene o-rings. FK FKM Fluoroelastomer W Polychloroprene Weighted FK FKM Fluoroelastomer N una-n GE Geolast FK FKM Fluoroelastomer GE Geolast PT PTFE PP Polypropylene GE Geolast PO PTFE/EPDM Overmolded SP Santoprene PT PTFE PT PTFE/Santoprene Two-Piece SS 316 Stainless Steel SP Santoprene SP Santoprene TP TPE TP TPE TP TPE TEX ertifications luminum 3300 and Stainless Steel 3300 pumps with aluminum center sections are certified: II 2 GD c II T4 78

81 Husky 3300 Metal Pumps Popular Models Diaphragm ir Valve Diaphragm O-Ring Material Part Number Seat Material all Material Material Replacement Kit Seat Kit all Kit Kit Kit luminum TPE cetal TPE 24K855 24K932 24K937 24K901 24K909 luminum Geolast Geolast Geolast 24K855 24K931 24K939 24K900 24K909 luminum Stainless Steel PTFE 2 pc PTFE 24K855 24K935 24K943 24K905 24K927 luminum cetal PTFE 2 pc PTFE 24K855 24K928 24K943 24K905 24K927 luminum Santoprene Santoprene Santoprene 24K855 24K934 24K944 24K902 24K909 Stainless Steel Stainless Steel PTFE 2 pc PTFE 24K857 24K935 24K943 24K905 24K927 Stainless Steel Santoprene Santoprene Santoprene 24K857 24K934 24K944 24K902 24K927 Stainless Steel Flange Models* Part Number Outlet Orientation Porting Seat Material all Material Diaphragm Material ir Valve Seat Kit all Kit Diaphgram Kit Rotatable enter Stainless Steel PTFE PTFE 24K860 24K935 24K943 24K Rotatable enter Santoprene Santoprene Santoprene 24K860 24K934 24K944 24K Rotatable enter Stainless Steel Santoprene Santoprene 24K860 24K935 24K944 24K902 Technical Specifications Husky 3300 Metal Pumps luminum Stainless Steel Maximum fluid working pressure with luminum enter Section with Polypropylene enter Section 125 psi (8.6 bar, 0.86 MPa) 125 psi (8.6 bar, 0.86 MPa) 100 psi (7.0 bar, 0.7 MPa) Maximum free flow delivery* Standard diaphragms at 125 psi (8.6 bar, 0.86 MPa) Standard diaphragms at 100 psi (7.0 bar, 0.7 MPa) Overmolded diaphragms at 125 psi (8.6 bar, 0.86 MPa) Overmolded diaphragms at 100 psi (7.0 bar, 0.7 MPa) Maximum pump speed* Standard diaphragms at 125 psi (8.6 bar, 0.86 MPa) Standard diaphragms at 100 psi (7.0 bar, 0.7 MPa) Overmolded diaphragms at 125 psi (8.6 bar, 0.86 MPa) Overmolded diaphragms at 100 psi (7.0 bar, 0.7 MPa) Maximum suction lift * (varies widely based on ball/seat selection and wear, operating speed, material properties, and other variables) 300 gpm (1,135 lpm) 280 gpm (1,059 lpm) 270 gpm (1,022 lpm) 260 gpm (984 lpm) 103 cpm 97 cpm 135 cpm 130 cpm 8 ft (2.4 m) dry 28 ft (8.5 m) wet 300 gpm (1,135 lpm) 280 gpm (1,059 lpm) 270 gpm (1,022 lpm) 260 gpm (984 lpm) 103 cpm 97 cpm 135 cpm 130 cpm 8 ft (2.4 m) dry 28 ft (8.5 m) wet Maximum size pumpable solids 0.5 in (13 mm) 0.5 in (13 mm) Noise (da)*** Sound Power at 50 psi (3.4 bar) and 50 cpm Sound Power at 120 psi (8.3 bar) and full flow Sound Pressure at 50 psi (3.4 bar) and 50 cpm Sound Pressure at 120 psi (8.3 bar) and full flow 92 da 99 da 86 da 93 da 92 da 99 da 86 da 93 da Maximum air consumption with luminum enter Section with Polypropylene enter Section ir pressure operating range with luminum enter Section with Polypropylene enter Section 335 scfm (9.5 m 3 /min.) 335 scfm (9.5 m 3 /min.) 275 scfm (7.8 m 3 /min.) 20 to 125 psi (1.4 to 8.6 bar, 0.14 to 0.86 MPa) 20 to 125 psi (1.4 to 8.6 bar, 0.14 to 0.86 MPa) 20 to 100 psi (1.4 to 7.0 bar, 0.14 to 0.7 MPa) ir inlet size 3/4 npt(f) 3/4 npt(f) Fluid inlet 3 in (76.2 mm) npt or bspt with NSI/DIN flange 3 in (76.2 mm) npt or bspt Weight 150 lb (68 kg) 255 lb (116 kg) Instruction manual Repair/parts manual * Maximum values with water as media at ambient temperature. Water level is approximately 3 feet above pumpinlet. ** Startup pressures and displacement per cycle may vary based on suction condition, discharge head, air pressure, and fluid type. *** Sound power measured per ISO Sound pressure was tested 3.28 ft (1 m) from equipment. 79

82 Husky 3300 Metal Pumps Performance harts Husky 3300 Performance pprox. ycles per Minute FLUID OUTLET PRESSURE psi (bar, MPa) 125 (8.6, 0.86) 100 (7, 0.69) 75 (5.2, 0.52) 50 (3.4, 0.34) 25 (1.7, 0.17) D D 375 (10.6) 300 (8.5) 225 (6.4) 150 (4.2) 75 (2.1) IR ONSUMPTION scfm (m 3 /min) gpm (lpm) (189) 100 (379) 150 (568) 200 (757) 250 (946) 300 (1136) FLUID FLOW (Pump tested in water with inlet submerged) IR PRESSURE LEGEND = at 125 psi (8.3 bar, 0.83 MPa) ir onsumption = at 100 psi (7 bar, 0.7 MPa) Fluid Pressure = at 70 psi (4.8 bar, 0.48 MPa) D = at 40 psi (2.8 bar, 0.28 MPa) Typical System Drawings D G 80

83 Husky 3300 Metal Pumps Dimensions luminum in. (30.6 cm) in. (61.2 cm) Stainless Steel in. (31.3 cm) in. (62.7 cm) ir Inlet (opposite side from muffler) ir Inlet (opposite side from muffler) in. (50.0 cm) in. (49.2 cm) in. (42.1 cm) in. (42.7 cm) in. (33.0 cm) 8.25 in. (21.0 cm) 16.5 in in. (41.9 cm) (42.9 cm) 13.0 in. (33.0 cm) 8.25 in. (21.0 cm) in. (42.9 cm) 16.5 in. (41.9 cm) 81

84 Husky Transfer Pump Packages 55 Gallon (208 liter) Size Ordering Information Pump omponents Drum Kit omponents Package Number Pump Type Pump Number Seats alls Diaphragms Drum Kit Number Tube Material Tube Part Number Easy Out Seal and Mounting ase Husky 515 Polypropylene Husky 515 cetal Husky 515 cetal Husky 716 luminum Husky 716 luminum Husky 716 luminum Husky 716 Stainless Steel Polypropylene PTFE PTFE Polypropylene cetal PTFE PTFE Stainless Steel cetal PTFE PTFE luminum cetal Santoprene Santoprene luminum cetal una-n una-n luminum cetal PTFE PTFE luminum D54311 Stainless Steel PTFE PTFE Stainless Steel Dimensions 8.5 in. (216 mm) 8.5 in. (216 mm) djustable from 2.6 in. (66 mm) to 5.1 in. (130 mm) 6.8 in. (173 mm) djustable from 2.6 in. (66 mm) to 5.1 in. (130 mm) 6.9 in. (175 mm) djustable from 2.6 in. (66 mm) to 5.1 in. (130 mm) djustable from 31.5 in. (800 mm) to 34.0 in. (864 mm) djustable from 31.5 in. (800 mm) to 34.0 in. (864 mm) djustable from 31.5 in. (800 mm) to 34.0 in. (864 mm) Poly, cetal and luminum Pumps Stainless Steel Pumps Overall height depends on pump. See page 12 or 15 for pump dimensions 82

85 Husky Transfer Pump Packages Technical Specifications cetal Polypropylene luminum Stainless Steel Husky 55 gal Transfer Pump Husky 515 Husky 515 Husky 716 Husky 716 Maximum Dimensions fluid working pressure 100 psi (7 bar, 0.7 MPa) 100 psi (7 bar, 0.7 MPa) 100 psi (7 bar, 0.7 MPa) 100 psi (7 bar, 0.7 MPa) Maximum free flow delivery* 12 gpm (57 lpm) 12 gpm (57 lpm) 14 gpm (61 lpm) 14 gpm (61 lpm) Maximum pump speed 400 cpm 400 cpm 400 cpm 400 cpm Displacement per cycle** 0.04 gallon (0.15 liter) 0.04 gallon (0.15 liter) 0.04 gallon (0.15 liter) 0.04 gallon (0.15 liter) Maximum size pumpable solids in (2.5 mm) in (2.5 mm) in (2.5 mm) in (2.5 mm) Typical sound level at 70 psi 67 da 67 da 67 da 67 da (4.9 bar, 0.49 MPa) 125 cpm Maximum air consumption 28 scfm (0.672 m3/min) 28 scfm (0.672 m3/min) 28 scfm (0.672 m3/min) 28 scfm (0.672 m3/min) ir pressure operating range 25 to 100 psi (1.8 to 7 bar, 0.18 to 0.7 MPa) 25 to 100 psi (1.8 to 7 bar, 0.18 to 0.7 MPa) 25 to 100 psi (1.8 to 7 bar, 0.18 to 0.7 MPa) 25 to 100 psi (1.8 to 7 bar, 0.18 to 0.7 MPa) ir inlet size 1/4 npt(f) 1/4 npt(f) 1/4 npt(f) 1/4 npt(f) ir exhaust port size 3/8 npt(f) 3/8 npt(f) 3/8 npt(f) 3/8 npt(f) Fluid inlet size 3/4 npt(f) 3/4 npt(f) 3/4 npt(f) 3/4 npt(f) Fluid outlet size 1/2 and 3/4 npt(f) 1/2 and 3/4 npt(f) 3/4 npt(f) 3/4 npt(f) Wetted parts (fluid covers and groundable acetal, PTFE polypropylene, PTFE aluminum, stainless steel, stainless steel, PTFE manifolds) PTFE, zinc-plated steel Pump weight 7.8 lb (3.5 kg) 6.5 lb (2.9 kg) 8.5 lb (3.9 kg) 18 lb (8.2 kg) Drum package weight tube material Drum kit weight easy-out seal material 12.3 lb (5.6 kg) aluminum 4.5 lb (2.0 kg) aluminum 14.3 lb (6.5 kg) stainless steel 6.5 lb (2.9 kg) stainless steel 10.5 lb (4.8 kg) polypropylene 4.0 lb (1.8 kg) polypropylene 13.0 lb (5.9 kg) aluminum 4.5 lb (2.0 kg) acetal 27.5 lb (12.5 kg) stainless steel 6.5 lb (2.9 kg) acetal Drum package instruction manual Instruction manual * Flow rates are with muffler and do not vary based on diaphragm material ** Displacement per cycle may vary based on suction condition, discharge head, air pressure and fluid type 9.5 lb (4.3 kg) stainless steel 83

86 Husky Transfer Pump Packages Pump and gitator Packages Ordering Information PRT NUMER HUSKY 55 GL (200 L) DISPENSING PKGE Husky 515 acetal pump , stainless steel drum cover , heavy-duty agitator , air-powered drum cover elevator , air controls, hose and dispense valve Husky 515 acetal pump, stainless steel drum cover, heavy-duty agitator, drum cover elevator PRT NUMER HUSKY TWISTORK PKGE Husky 515 D52911 Polypropylene pump mounted on Twistork Husky 515 D51911 cetal pump mounted on Twistork Technical Specifications Husky 515 on Twistork gitator Maximum air input pressure 100 psi (7 bar) Maximum fluid output pressure 100 psi (7 bar) Maximum siphon flow rate with 100 cps material with 1000 cps material 12 gpm (45.4 lpm) 1.2 gpm (4.54 lpm) ir inlet Quick-coupler, nipple (pin) Fluid outlet size 3/4 npt(f) Maximum recommended agitator speed 800 rpm gitator air consumption at 400 rpm at 800 rpm 2.5 scfm (0.07 m3 /min) 5.7 scfm (0.16 m3 /min) Pump air consumption at 12 gpm (45.4 lpm) approximately 12 scfm (0.34 m3 /min) Maximum operating temperature 150º F (66º ) Weight 32 lb (14.5 kg) Maximum noise level* 85 d() Instruction manual * Tested to GI-PNEUROP

87 Husky Transfer Pump Packages Dimensions Husky 55 gal Dispensing Package Husky Twistork Package height of unit from base to top of pump when elevator is raised 10.7 in (272 mm) 95 in. (2413 mm) 8.7 in (221 mm) 7.9 in (201 mm) 10.8 in (274 mm) 32 in (813 mm) minimum 35.1 in (892 mm) maximum 61.1 in (1552 mm) 57 in. (1448 mm) Elevator ase Mounting Hole Layout 8.88 in. (225.6 mm) 5.5 in. (140 mm) 0.56-in. (14.2 mm) holes 85

88 Husky Pump ccessories ir-operated Double Diaphragm Husky 205 ccessories Part Number IR ONTROLS Regulator / Filter ssembly 1/4 npt(f) (6.35 mm) Quick onnect ir oupler 1/4 npt (6.35 mm) Quick onnect ir Nipple 1/4 npt (6.35 mm) mbe ir Shut Off Valve 1/4 npt (6.35mm), bleed type, relieves trapped air downline of valve ir Runaway Valve (stops pump from cavitating when empty) ir Muffler (comes with pump) GLLON SIPHON KITS Polypropylene Suction Kit (includes siphon hose, tube and connectors) cetal Suction Kit (includes siphon hose, tube and connectors) PVDF Suction Kit (includes siphon hose, tube and connectors) REMOTE PUMP ONTROLLERS ycleflo (cpm rate and batch control) v ycleflo II (rate controller with solenoid valve) 120v Husky 307 ccessories IR ONTROLS Regulator / Filter ssembly 1/4 npt(f) (6.35 mm) Quick onnect ir oupler 1/4 npt (6.35 mm) Quick onnect ir Nipple 1/4 npt (6.35 mm) mbe ir Shut Off Valve 1/4 npt (6.35 mm), bleed type, relieves trapped air downline of valve ir Runaway Valve (stop pump from cavitating when empty) ir Muffler (comes with pump) GLLON SIPHON KITS Polypropylene Suction Kit (includes siphon hose, tube and connectors) cetal Suction Kit (includes siphon hose, tube and connectors) REMOTE PUMP ONTROLLERS Husky 307 pumps are not equipped to run in remote mode N/ SPLIT MNIFOLD KITS y varying the manifold kits, pumps can be configured in different ways (one inlet and two outlets, two inlets and one outlet, and two inlets and two outlets, etc), allowing for system flexibility. Pumps need to be ordered separately. One kit is required for each side (top or bottom). See for details. cetal Split Manifold Kit Polypropylene Split Manifold Kit Rubber Foot Kit WLL MOUNTING RKET Wall mounting bracket for Husky 307 pumps

89 Husky Pump ccessories Husky 515 and Husky 716 ccessories Part Number IR ONTROLS Regulator / Filter ssembly 1/4 npt(f) (6.35 mm) Quick onnect ir oupler 1/4 npt (6.35 mm) Quick onnect ir Nipple 1/4 npt (6.35 mm) mbe ir Shut Off Valve 1/4 npt (6.35 mm), bleed type, relieves trapped air downline of valve ir Runaway Valve (stop pump from cavitating when empty) ir Muffler (comes with pump) enter Section onversion Kit (converts an old style Husky 715 to a Husky 515/716) enter Section onversion Kit (converts an old remote style Husky 715 to a Husky 515/716) GLLON SIPHON KITS Drum Kit (includes easy out seal mounting base and siphon tube). Pump models can be mounted to base, but may require opening bottom inlet. See for details. Mounting ase with a Polypropylene Siphon Tube Mounting ase with a luminum Siphon Tube Mounting ase with a Stainless Steel Siphon Tube (used with non sst pumps) Mounting ase with a Stainless Steel Siphon Tube (for sst pump only) REMOTE PUMP ONTROLLERS ycleflo (cpm rate and batch control) v ycleflo II (rate controller with solenoid valve) 120v SPLIT MNIFOLD KITS (HUSKY 515 ONLY) y varying the manifold kits, pumps can be configured in different ways (one inlet and two outlets, two inlets and one outlet, and two inlets and two outlets, etc), allowing for system flexibility. Pumps need to be ordered separately. See manual for details. Polypropylene Inlet Manifolds Polypropylene Outlet Manifolds cetal Inlet Manifolds cetal Outlet Manifolds PVDF Inlet Manifolds PVDF Outlet Manifolds WLL MOUNTING RKET Wall mounting bracket for Husky 515 & Husky 716 pumps MISELLNEOUS ESSORIES Duckbill Replacement Parts (urethane) for 515 and 716 Husky Pumps SURGE SUPPRESSORS Surge suppressors are designed to reduce the pulsation caused during pump changeover. The suppressor construction is generally closely matched with the pump s material (Stainless Steel with Stainless Steel, cetal with luminum, etc.) and are available in either an adjustable or automatic version. See for details. utomatic Husky 750, 3/4 (19.05 mm) Polypropylene (wetted bottom and top housings) with a una-n bladder with PTFE bellows with a Fluoroelastomer bladder

90 Husky Pump ccessories Husky 515 and Husky 716 ccessories (continued) Part Number SURGE SUPPRESSORS (ONTINUED) Stainless Steel (wetted bottom and top housings) with a una-n bladder with PTFE bellows with a Fluoroelastomer bladder cetal (wetted bottom and top housings) with a una-n bladder with PTFE bellows djustable Husky 750, 3/4 (19.05 mm) Polypropylene (wetted bottom and top housings) with a una-n bladder with PTFE bellows with a Fluoroelastomer bladder Stainless Steel (wetted bottom and top housings) with a una-n bladder with PTFE bellows with a Fluoroelastomer bladder cetal (wetted bottom and top housings) with a una-n bladder with PTFE bellows PTFE/EPDM OVERMOLDED DIPHRGMS Industrial upgrade kits includes new airside diaphragm plate Upgrade kit for 0.5 in (1.27 cm) and 0.75 in (1.905 cm) pump 24N321 LEK DETETOR Leak detectors are designed to shut off the pump in the event a diaphragm fails. The leaking material flows out the air section and is captured by the leak detector reservoir. Once the reservoir is filled, a signal is sent that would shut off the pump. These detectors should only be used when a massive failure is allowed. Polypropylene Housings with PV Wetted Parts Shut Off Valve Kit (used in conjunction with ) Husky 1050, 1050HP, 1590, 15120, 2150, 2200 ccessories IR ONTROLS Regulator / Filter ssembly 1/2 npt(f) (12.7 mm) Quick onnect ir oupler 1/2 npt (12.7 mm) Quick onnect ir Nipple 1/2 npt (12.7 mm) mbe ir Shut Off Valve 1/2 npt (12.7mm), bleed type, relieves trapped air downline of valve ir Runaway Valve (stop pump from cavitating when empty) ir Muffler (comes with pump) 1050 pumps 24D642 ir Muffler (comes with pump) 1590 and 2150 pumps enter Section onversion Kit (converts an aluminum center section to sst. Includes air covers). Husky Husky GLLON SIPHON KIT Siphon kit is used for drawing fluids from 55-gallon sized containers, through a 2 bung opening. Kit comes with carbon steel tube, 8 (2.44m) polyethylene hose and couplings REMOTE PUMP ONTROLLERS ycleflo (cpm rate and batch control) v ycleflo II (rate controller with solenoid valve) 120v DUL INLET MNIFOLD luminum Husky 1050 only 24D205 ONVERSION KITS Remote Valve onversion Kit for luminum Husky 1050 only 24D037 Remote Valve onversion Kit for Polypropylene Husky 1050 only 24D038 Remote Valve onversion Kit for onductive Polypropylene Husky 1050 only 24D039 88

91 Husky Pump ccessories Husky 1050, 1050HP, 1590, 15120, 2150, 2200 ccessories (continued) Part Number SURGE SUPPRESSORS Surge suppressors are designed to reduce the pulsation caused during pump changeover. The suppressor construction is generally closely matched with the pump s material (Stainless Steel with Stainless Steel, cetal with luminum, etc.) and are available in either an adjustable or automatic version. See for details. utomatic Husky 2000, 2 in (50.8 mm) Polypropylene (wetted bottom and top housings) with a una-n bladder with PTFE bellows Stainless Steel (wetted bottom and top housings) with a una-n bladder with PTFE bellows with a Fluoroelastomer bladder djustable Husky 2000, 2 in (50.8 mm) Polypropylene (wetted bottom and top housings) with a una-n bladder with PTFE bellows Stainless Steel (wetted bottom and top housings) with a una-n bladder with PTFE bellows with a Fluoroelastomer bladder PTFE/EPDM OVERMOLDED DIPHRGMS Industrial upgrade kits includes new airside diaphragm plate Upgrade kit for 1 inch (2.54 cm) Husky 1040 pump Upgrade kit for 1 inch (2.54 cm) Husky 1050 pump Upgrade kit for 1.5 inch (3.81 cm) pump Upgrade kit for 2 inch (5.08 cm) pump LEK DETETOR Leak detectors are designed to shut off the pump in the event a diaphragm fails. The leaking material flows out the air section and is captured by the leak detector reservoir. Once the reservoir is filled, a signal is sent that would shut off the pump. These detectors should only be used when a massive failure is allowed. Polypropylene Housings with PV Wetted Parts Shut Off Valve Kit (used in conjunction with ) WLL MOUNTING RKET Wall mounting bracket for Husky 1050 pumps Dampener repair kit for feet mounting on the wall bracket Isolator replacement kit (SPR 9026) 24E769 MISELLNEOUS ESSORIES Flange Kits. Used to transition a flanged pump to a npt connection to transition from a threaded connection to a flange. It is recommended that the flange kit be compatible with the pump material. Polypropylene 1 inch (24.14 mm) flange for Husky 1050 D72XXX pumps. 1 NSI x 1 npt (f) Stainless Steel 1 inch (24.14 mm) flange for Husky 1050 D71XXX and D74XXX pumps 1 NSI x 1 npt (f) PVDF 1 inch (24.14 mm) flange for Husky 1050 D75XXX pump 1 NSI x 1 npt (f) Polypropylene 1-1/2 inch (36.84 mm) flange for Husky 1590 D2XXX pump 1-1/2 NSI x 1-1/2 (f) PVDF 1-1/2 inch (36.84 mm) flange for Husky 1590 D5XXX pump. 1-1/2 NSI x 1-1/2 (f) Polypropylene 2 inch (48.28 mm) flange for Husky 2150 DF2XXX pump. 2 NSI x 2 (f) PVDF 2 inch (48.28 mm) flange for Husky 2150 DF5XXX pump 2 NSI x 2 (f)

92 Husky Pump ccessories Husky 3300 ccessories IR ONTROLS Regulator / Filter ssembly 3/4 npt(f) (19.5 mm) Quick onnect ir oupler 3/4 npt (19.5 mm) Quick onnect ir Nipple 3/4 npt (19.5 mm) mbe ir Shut Off Valve 3/4 npt (19.5 mm), bleed type, relieves trapped air downline of valve ir Runaway Valve (stop pump from cavitating when empty) ir Muffler (comes with pump) GLLON SIPHON KITS Typically, 3 pumps are not used for emptying 55-gallon containers N/ REMOTE PUMP ONTROLLERS Husky 3300 pumps are not equipped to run in remote mode N/ SPLIT MNIFOLD KITS There are no Husky 3300 with a split manifold option N/ SURGE SUPPRESSORS Surge suppressors are designed to reduce the pulsation caused during pump changeover. The suppressor construction is generally closely matched with the pump s material (Stainless Steel with Stainless Steel, cetal with luminum, etc.) and are available either in adjustable or automatic version. See for details. utomatic Husky 2000, 2 in (50.8 mm) Polypropylene (wetted bottom and top housings) with a una-n bladder with PTFE bellows djustable Husky 2000, 2 in (50.8 mm) Polypropylene (wetted bottom and top housings) with a una-n bladder with PTFE bellows Popular Industrial Pump ombinations with PTFE/EPDM Overmolded Diaphragms* Pump Part No. Pump Size ir Motor Fluid Section Seats alls Threads 24N in Poly Poly Poly PTFE NPT 24N in Poly Poly Poly PTFE SPT 24N in Poly PVDF PVDF PTFE NPT 24N in Poly cetal cetal PTFE NPT 24N in Poly cetal SST SST NPT 24N in Poly cetal cetal PTFE SPT 24N in Poly L cetal PTFE NPT 24N in Poly L SST PTFE NPT 24N in Poly L SST SST NPT 24N in Poly SST cetal PTFE NPT 24N in Poly SST SST PTFE NPT 24N in Poly SST SST SST NPT in Poly Poly SST PTFE NPT in L SST SST PTFE NPT in Poly PVDF PVDF PTFE NPT in L L SST SST NPT in L L SST PTFE NPT in Poly Poly Poly PTFE enter Flange in Poly Poly Poly PTFE End Flange in Poly PVDF PVDF PTFE End Flange in L SST SST SST NPT in L SST SST PTFE SPT in Poly SST SST PTFE NPT Pump Part No. Pump Size ir Motor Fluid Section Seats alls Threads in L SST SST PTFE NPT in L Poly SST PTFE End Flange in L Poly Poly PTFE End Flange in SST SST SST PTFE NPT 24G in L L SST PTFE SPT 24J in L L SST PTFE NPT 24J in L L SST cetal NPT in L SST SST PTFE NPT in L L SST PTFE NPT in L Poly SST PTFE End Flange in L Poly Poly PTFE End Flange in SST SST SST PTFE NPT 24J in L L SST cetal NPT 24G in L L SST PTFE SPT in L ast Iron SST PTFE NPT in L ast Iron SST Geolast NPT in L ast Iron SST Santo NPT * Over 500 industrial pump models available with overmolded diaphragm options. Visit Husky pump selector at for more configuration models. 90

93 ycleflo and ycleflo II Solenoid Pump ontrollers Ordering Information ycleflo Pneumatic pump controller, V ycleflo II Pneumatic pump controller, 120V ycleflo Instruction Manual ycleflo II Instruction Manual Product Selector Highlighted areas indicate the different sizes of remote pumps and available materials of construction for seats, balls and diaphragms that can be used with the ycleflo and ycleflo II controller. PUMP SIZE (air motor type and material) WETTED PRTS SETS LLS DIPHRGM 2 = 1/4 (6.35 mm) Remote: polypropylene center section 1 = cetal (NPT) 0 = Seat with ball 1 = PTFE 1 = PTFE 4 = 1/2 (12.7 mm) Remote: polypropylene center section 2 = Poly (NPT) 2 = cetal 2 = cetal 5 = TPE 4 = 3/4 (19.05 mm) Remote: polypropylene center section 3 = luminum (NPT) 3 = Stainless Steel 3 = Stainless Steel 6 = Santoprene = 1-1/2 (38.1 mm) Remote: aluminum center section 4 = Stainless Steel (NPT) 4 = Hardened SST 4 = Hardened SST 7 = una-n U = 1-1/2 (38.1 mm) Remote: stainless steel center section 5 = PVDF (NPT) 5 = TPE 5 = TPE 8 = Fluoroelastomer G = 2 (50.8 mm) Remote: aluminum center section 6 = Ductile Iron (NPT) 6 = Santoprene 6 = Santoprene G = Geolast 7 = una-n 7 = una-n = cetal * (SPT) 8 = Fluoroelastomer 8 = Fluoroelastomer = Poly * (SPT) 9 = Polypropylene 9 = Polypropylene = luminum (SPT) = PVDF = PVDF D = Stainless Steel (SPT) G = Geolast G = Geolast E = PVDF (SPT) F = Ductile Iron (SPT) = SST with viton seal = Santoprene with H = 2 npt lum Extended viton seal G = 2 bsp lum Extended D = Urethane Duckbill Mounting Dimensions ycleflo ycleflo II 4 in (102 mm) in (187 mm) in (225 mm) 5 in (127 mm) in (187 mm) 5 in (127 mm) 91

94 ycleflo and ycleflo II How To Determine The est Remote Pump: 1. onfigure the best seat, ball and diaphragm combination, as well as fluid wetted parts, based on material compatibility and application requirements. If the material is a mild acid, the choice could be a DX Determine dispense time and volume accuracy. In two minutes, 50 gallons need to be dispensed ±5% accuracy 3. Use the displacement volume chart below to choose the pump size with an outlet volume/cycle that is most closely divisible into your required flow.* Husky 1590 produces.5 gal/cycle Husky 2150 produces 1.03 gal/cycle Husky 205 Husky 515 Husky 716 Husky 1050 Husky 1050HP Husky 1590 Husky Husky 2150 Husky 2200 Volume/cycle 1/4 in 1/2 in 3/4 in 1 in 1 in 1-1/2 in 1-1/2 in 2 in 2 in ubic centimeters (cc) Liters Grams (assumes s.g =1.0) Kilograms (kg) Gallons Quarts Pints Ounces ubic inch Determine the number of cycles required. alculate the dispense time by dividing required flow by outlet volume per cycle. Husky 1590 = 50 gal/0.5 gal/cycle = 100 cycles Husky 2150 = 50 gal/1.03 gal/cycle = cycles 5. Determine if cycle output is within the dispense accuracy required. Husky 2150 requires cycles to pump 50 gallons. Only full cycles are possible, so either 48 or 49 cycles can be counted. t the 48 cycle count, dispense would be gallons. t the 49 cycle count, dispense would be gallons. Husky 1590 requires 100 cycles to pump 50 gallons. No partial cycles required. 6. fter determining the best size, use the pump ordering matrix to decide which remote center section is most suitable for the application D2911 (aluminum center section) or DU5911 (stainless steel center section). Since a mild acid is being pumped, D2911, an aluminum center section would be the best choice. ycleflo ycleflo II * Displacement values are estimates based on average running conditions. 92

95 Surge Suppressors Husky 750 and Husky 2000 Ordering Information Husky 750, 3/4 in npt(f) Surge Suppressors utomatic Polypropylene wetted bottom housing and non-wetted top housing Stainless Steel wetted bottom housing and non-wetted top housing Weight 9 lb (4.1 kg) 16 lb (7.3 kg) Suppressor with una-n bladder Suppressor with PTFE bellows Suppressor with Fluoroelastomer bladder djustable Polypropylene wetted bottom housing and non-wetted top housing Stainless Steel wetted bottom housing and non-wetted top housing Weight 9 lb (4.1 kg) 16 lb (7.3 kg) Suppressor with una-n bladder Suppressor with PTFE bellows Suppressor with Fluoroelastomer bladder Husky 2000, 2 in npt(f) Surge Suppressors utomatic Polypropylene wetted bottom housing and non-wetted top housing Weight 18 lb (8.2 kg) 36 lb (16.3 kg) Suppressor with una-n bladder Suppressor with PTFE bellows Suppressor with Fluoroelastomer bladder n/a djustable Polypropylene wetted bottom housing and non-wetted top housing Weight 18 lb (8.2 kg) 36 lb (16.3 kg) Suppressor with una-n bladder Suppressor with PTFE bellows Suppressor with Fluoroelastomer bladder n/a Stainless Steel wetted bottom housing, polypropylene non-wetted top housing Stainless Steel wetted bottom housing, polypropylene non-wetted top housing utomatic utomatic djustable utomatic Technical Specifications djustable Surge Suppressors Husky 750 Husky 2000 Max. air input pressure 120 psi (0.84 MPa, 8.4 bar) 120 psi (0.84 MPa, 8.4 bar) ir line connection 1/4 npt 1/4 npt Fluid inlet size 3/4 in npt(f) 2 in npt(f) Instruction manual

96 Husky 1050e Pumps Electric Double Diaphragm Selector Tool To order a Husky 1050e, use the online selector tool at or contact your distributor. NOTE: heck the identification plate (ID) for the onfiguration Number of your pump. Use the following matrix to define the components of your pump. Example of Product Selector Tool on Pump onfiguration Options Pump 1050 Wetted Section Material Drive Type enter Section Material Motor and Gearbox luminum E Electric luminum 04 Standard Induction Motor with Gearbox P Polypropylene S Stainless Steel 04 rushless D Motor S Stainless Steel 04 Induction Motor, TEX t 04D Explosionproof Induction Motor «04E NEM Gearbox + 04F IE Gearbox + 05 Standard Induction Motor with ompressor (120V) 05 rushless D Motor with ompressor (120V) 06 Standard Induction Motor with ompressor (240V) 06 rushless D Motor with ompressor (240V) Fluid overs and Manifolds Seat Material all Materials Diaphragm Material Manifold 0-Rings 1 luminum, NPT cetal cetal N una-n -- Models with 2 luminum, SPT L luminum N una-n O Polychloroprene Overmold N, FK, or TP P1 Polypropylene, center flange N una-n R Polychloroprene Standard FK FKM Fluoroelastomer seats do not use P2 Polypropylene, end flange FK FKM Fluoroelastomer W Polychloroprene Weighted GE Geolast o-rings S1 Stainless steel, NPT GE Geolast FK FKM Fluoroelastomer PO PTFE/EPDM Overmold PT PTFE S2 Stainless steel, SPT PP Polypropylene GE Geolast PT PTFE/EPDM 2 Piece SP Santoprene PT PTFE PS PTFE/Santoprene 2 Piece SS 316 Stainless Steel SP Santoprene SP Santoprene TP TPE SS 316 Stainless Steel TP TPE TP TPE pprovals: t luminum and stainless steel pumps with code 04 are certified: «Motors coded 04D are certified: + luminum and stainless steel pumps with code 04E or 04F are certified: ll Models (except 04D, 05, and 05) are certified: 94 II 2 G ck Ex d II T3 Gb lass1, Zone 1, Ex d II T3 0 <Ta<40 II 2 G ck II T3 Gb

97 Husky 1050e Pumps Popular Models Husky 1050e Popular Models Part Number enter Section Fluid Section Porting Seat all Diaphragm Motor* ompressor** luminum luminum NPT Hytrel cetal Hytrel Standard 2 HP Yes (120V) luminium luminium SPT Hytrel cetal Hytrel Standard 2 HP Yes (240V) luminum luminum NPT Santoprene Santoprene Santoprene Standard 2 HP Yes (120V) luminium luminium SPT Santoprene Santoprene Santoprene Standard 2 HP Yes (240V) luminum luminum NPT Stainless Steel Weighted Neoprene Neoprene Overmolded rushless D Yes (120V) luminium luminium SPT Stainless Steel Weighted Neoprene Neoprene Overmolded rushless D* Yes (240V) luminum luminum NPT Stainless Steel PTFE 2-Piece PTFE w/ Santoprene acker rushless D Yes (120V) luminium luminium SPT Stainless Steel PTFE 2-Piece PTFE w/ Santoprene acker Standard 2 HP Yes (240V) luminum luminum NPT una-n una-n una-n rushless D Yes (120V) luminium luminium NPT una-n una-n una-n rushless D Yes (240V) luminum Polypropylene enter Flange Santoprene Santoprene Santoprene Standard 2 HP Yes (120V) luminium Polypropylene enter Flange Santoprene Santoprene Santoprene Standard 2 HP Yes (240V) luminum Polypropylene enter Flange Polypropylene PTFE 2-Piece PTFE w/ Santoprene acker rushless D Yes (120V) luminium Polypropylene enter Flange Polypropylene PTFE 2-Piece PTFE w/ Santoprene acker Standard 2 HP Yes (240V) luminum Polypropylene enter Flange Polypropylene PTFE PTFE Overmolded rushless D Yes (120V) luminium Polypropylene enter Flange Polypropylene PTFE PTFE Overmolded rushless D Yes (240V) Stainless Steel Polypropylene enter Flange Polypropylene PTFE 2-Piece PTFE w/ Santoprene acker rushless D Yes (120V) Stainless Steel Polypropylene enter Flange Polypropylene PTFE 2-Piece PTFE w/ Santoprene acker rushless D Yes (240V) luminum Stainless Steel NPT Stainless Steel PTFE 2-Piece PTFE w/ Santoprene acker Standard 2 HP Yes (120V) luminium Stainless Steel SPT Stainless Steel PTFE 2-Piece PTFE w/ Santoprene acker Standard 2 HP Yes (240V) Stainless Steel Stainless Steel NPT Stainless Steel PTFE PTFE Overmolded Standard 2 HP Yes (120V) Stainless Steel Stainless Steel NPT Stainless Steel PTFE PTFE Overmolded Standard 2 HP Yes (240V) luminum Stainless Steel NPT Stainless Steel PTFE 2-Piece PTFE w/ Santoprene acker rushless D Yes (120V) luminium Stainless Steel SPT Stainless Steel PTFE 2-Piece PTFE w/ Santoprene acker rushless D Yes (240V) *rushless D includes Graco ontroller Husky 1050e Hazardous Location Pumps Part Number enter Section Fluid Section Porting Seat all Diaphragm Motor ompressor luminum luminum NPT Santoprene Santoprene Santoprene 2 HP North merican lass 1, Div 1 No luminum luminum NPT Stainless Steel PTFE 2-Piece PTFE w/ Santoprene acker 2 HP TEX Motor No luminium luminium SPT Stainless Steel PTFE 2-Piece PTFE w/ Santoprene acker 2 HP TEX Motor No luminum Stainless Steel NPT Stainless Steel PTFE 2-Piece PTFE w/ Santoprene acker 2 HP North merican lass 1, Div 1 No luminum Stainless Steel NPT Stainless Steel PTFE 2-Piece PTFE w/ Santoprene acker 2 HP TEX Motor No luminium Stainless Steel SPT Stainless Steel PTFE 2-Piece PTFE w/ Santoprene acker 2 HP TEX Motor No Husky 1050e art Mounted Systems Part Number enter Section Fluid Section Porting Seat all Diaphragm Motor* ompressor 24Y388 luminum luminum NPT Stainless Steel Weighted Neoprene Neoprene Overmolded rushless D Yes (120V) 24Y553 luminum luminum NPT Santoprene Santoprene Santoprene rushless D Yes (120V) 24Y554 luminium luminium NPT Santoprene Santoprene Santoprene rushless D Yes (240V) 24Y555 luminum luminum NPT Hytrel cetal Hytrel rushless D Yes (120V) 24Y556 luminium luminium NPT Hytrel cetal Hytrel rushless D Yes (240V) 24Y557 luminum luminum NPT una-n una-n una-n rushless D Yes (120V) 24Y558 luminium luminium NPT una-n una-n una-n rushless D Yes (240V) 24Y559 luminum Polypropylene End Flange Polypropylene PTFE 2-Piece PTFE w/ Santoprene acker rushless D Yes (120V) 24Y560 luminium Polypropylene End Flange Polypropylene PTFE 2-Piece PTFE w/ Santoprene acker rushless D Yes (240V) 24Y561 luminum Stainless Steel NPT Stainless Steel PTFE 2-Piece PTFE w/ Santoprene acker rushless D Yes (120V) 24Y562 luminium Stainless Steel NPT Stainless Steel PTFE 2-Piece PTFE w/ Santoprene acker rushless D Yes (240V) *rushless D includes Graco motor control and compressor **Options available without compressor 95

98 Husky 1050e Pumps ccessories Part Number enter Section 24Y661 Leak sensor kit for Husky 1050e pumps 16K911 VFD (Variable Frequency Drive), 2 Horsepower V Single or Three Phase Input Power 16K912 VFD (Variable Frequency Drive), 2 Horsepower V Three Phase Input Power 24Y e ompressor ox Kit (240V) 24Y e ompressor ox Kit (120V) 24Y543 art kit for Husky 1050e 17F734 2 Horsepower Explosion Proof lass 1 Division 1 Motor 17F745 2 Horsepower TEX Hazardous Location Motor 17J334 earing Puller Tool 24Y627 ushing Installation Tool Flange Kit - Polypropylene 1" NSI x 1" npt(f) Flange Kit - Stainless Steel 1" NSI x 1" npt(f) Flange Kit - PVDF 1" NSI x 1" npt(f) Overmolded PTFE Upgrade Kit 24D205 Dual Inlet Manifold for luminum Husky 1050e Technical Specifications Husky 1050e Maximum fluid working pressure ir pressure operating range ir inlet size 70 psi (4.8 bar, 0.48 Mpa) 20 to 80 psi (1.4 to 5.5 bar, 0.14 to 0.55 MPa) 3/8 in npt(f) Maximum suction lift* Wet: 29 ft (8.8 m); Dry: 16 ft (4.9 m) Maximum size pumpable solids mbient air temperature range for operation and storage** 1/8 in (3.2 mm) 32 F to 104 F (0 to 40 ) Fluid displacement per cycle 0.17 gallons (0.64 L) Maximum free-flow delivery Maximum pump speed 42 gpm (158 lpm) 280 cpm Fluid Inlet and outlet Size luminum and stainless steel Polypropylene motor power LD motor power Operation manual in npt(f) or 1 in bspt 1 in NSI/DIN Raised Face Flange 2 HP 2.2 HP 96

99 Husky 1050e Pumps Performance harts Outlet Pressure - PSI (MPa, bar) Pump with 2hp VFD Frequency - Hz (Pump Speed per Minute) (36) (72) (109) (145) (181) (217) (253) (290) 80 (5.5, 0.55) 70 (4.8, 0.48) 60 (4.1, 0.41) 50 (3.4, 0.34) 40 (2.8, 0.28) 30 (2.1, 0.21) 20 (1.4, 0.14) 10 (0.7, 0.07) (19) (38) (57) (76) (95) (114) (132) (151) Fluid Flow - gpm (lpm) NPSHr (feet W) Outlet Pressure - PSI (MPa, bar) rushless D Motor Pump Speed in ycles per Minute (5.5, 0.55) (4.8, 0.48) 60 (4.1, 0.41) 50 (3.4, 0.34) 40 (2.8, 0.28) (2.1, 0.21) 20 (1.4, 0.14) 10 (0.7, 0.07) (19) (38) (57) (76) (95) (114) (132) (151) Fluid Flow - gpm (lpm) NPSHr (feet W) KEY = Power Limit urve = Net Positive Suction Head Required LEGEND ontinuous Duty Operating Range KEY = Power Limit urve = Net Positive Suction Head Required LEGEND ontinuous Duty Operating Range 60 (4.1, 0.41) Low Pulsation Mode Frequency Outlet Pressure - PSI (MPa, bar) 50 (3.4, 0.34) 40 (2.8, 0.28) 30 (2.1, 0.21) 20 (1.4, 0.14) D E F G 10 (0.7, 0.07) (19) (38) (57) (76) (95) Fluid Flow - gpm (lpm) KEY = 22 Hz, 80 cycles per minute D = 25 psi (1.7 bar) air pressure = 31 Hz, 115 cycles per minute E = 37 psi (2.5 bar) air pressure = 40 Hz, 150 cycles per minute F = 50 psi (3.5 bar) air pressure G = Transition line (Low Pulsation Mode is shaded) 97

100 Husky 1050e Pumps Dimensions Husky 1050e luminum J E G F D H Gearbox Only (04E and 04F) Gearbox and Motor (04, 04 and 04D) LD (04) Gearbox, Motor and ompressor (05 and 06) LD (05 and 06) Ref. in cm in cm in cm in cm in cm D N N 04D 04D E F G E 04E F 04F H N 04D 04D E 04E F 04F J N 04D 04D Husky 1050e Stainless Steel G E D J H Gearbox Only (04E and 04F) Gearbox and Motor (04, 04 and 04D) LD (04) Gearbox, Motor and ompressor (05 and 06) LD (05 and 06) Ref. in cm in cm in cm in cm in cm D N N 04D 04D E G E 04E F 04F H N 04D 04D E 04E F 04F J N 04D 04D Refer to manual for additional dimensions 98

101 Husky 1050e Pumps Dimensions Husky 1050e Polypropylene G J H E D Ref. Gearbox Only (04E and 04F) (04, 04 and 04D) Gearbox and Motor LD (04) Gearbox, Motor and ompressor (05 and 06) LD (05 and 06) in cm in cm in cm in cm in cm D N E enter Flange E End Flange 04D D G E E F 04F H N 04D 04D E E F 04F J N 04D 04D N Refer to manual for additional dimensions 99

102 SoloTech Hose Pumps Positive Displacement Hose Pumps Selector Tool To order a SoloTech pump, use the online selector tool at or contact your distributor. Pump onfiguration Options heck the identification plate (ID) for the onfiguration Number of your pump. Use the following matrix to define the components of your pump. Pump Hose Size Hose Material/olor ST mm motor with low-speed gear reducer NR Natural Rubber/lack mm motor with medium-speed gear reducer S hlorosulfonated Polyethylene (SM)/Orange mm motor with high speed gear reducer EP Ethylene propylene diene monomar (EPDM)/lue mm rushless D (LD) motor with gear reducer N Nitrile (NR/Yellow) arb Materials Roller Housing Options SS Stainless Steel 1 luminum 1 luminum 0 None PV PVDF HS Hastelloy Popular Models Graco Pumps with LD Motors (Includes Graco ontroller) hoose Your Hose & Hose arb Materials Hose Material Hose arb Material SoloTech 10 SoloTech 23 SoloTech 26 SoloTech 30 Natural Rubber 316 SST 19Z001 19Z033 19Z065 19Z097 PVDF 19Z196 19Z200 19Z204 19Z SST 19Z002 19Z034 19Z066 19Z098 SM PVDF 19Z003 19Z035 19Z067 19Z101 Hastelloy- 19Z004 19Z039 19Z071 19Z103 Nitrile 316 SST 19Z005 19Z038 19Z070 19Z SST 19Z006 19Z036 19Z068 19Z099 EPDM PVDF 19Z007 19Z037 19Z069 19Z102 Hastelloy- 19Z008 19Z040 19Z072 19Z

103 SoloTech Hose Pumps Graco Pumps with Motors hoose Your Hose & Hose arb Materials Hose Material Hose arb Material SoloTech 10 SoloTech 23 SoloTech 26 SoloTech 30 Low Mid High Low Mid High Low Mid High Low Mid High Natural Rubber 316 SST 19Z009 19Z017 19Z025 19Z041 19Z049 19Z057 19Z081 19Z089 19Z073 19Z121 19Z105 19Z113 PVDF 19Z195 19Z194 19Z193 19Z199 19Z198 19Z197 19Z203 19Z202 19Z201 19Z207 19Z206 19Z SST 19Z010 19Z018 19Z026 19Z042 19Z050 19Z058 19Z082 19Z090 19Z074 19Z122 19Z106 19Z114 SM PVDF 19Z011 19Z019 19Z027 19Z045 19Z053 19Z061 19Z085 19Z093 19Z077 19Z125 19Z109 19Z117 Hastelloy- 19Z012 19Z021 19Z029 19Z046 19Z055 19Z063 19Z087 19Z095 19Z078 19Z127 19Z111 19Z119 Nitrile 316 SST 19Z013 19Z020 19Z028 19Z044 19Z052 19Z060 19Z084 19Z092 19Z076 19Z124 19Z108 19Z SST 19Z014 19Z022 19Z030 19Z043 19Z051 19Z059 19Z083 19Z091 19Z075 19Z123 19Z107 19Z115 EPDM PVDF 19Z015 19Z023 19Z031 19Z047 19Z054 19Z062 19Z086 19Z094 19Z079 19Z126 19Z110 19Z118 Hastelloy- 19Z016 19Z024 19Z032 19Z048 19Z056 19Z064 19Z088 19Z096 19Z080 19Z128 19Z112 19Z120 Hose Pumps with No Motor Drive and NEM onnection hoose Your Hose & Hose arb Materials Hose Material Hose arb Material SoloTech 10 SoloTech 23 SoloTech 26 SoloTech 30 Low Mid High Low Mid High Low Mid High Low Mid High Natural Rubber 316 SST 19X009 19X041 19X025 19X057 19X089 19X073 19X105 19X137 N 19X153 19X185 19X SST 19X010 19X042 19X026 19X058 19X090 19X074 19X106 19X138 N 19X154 19X186 19X170 SM PVDF 19X011 19X043 19X027 19X059 19X091 19X075 19X107 19X139 N 19X156 19X188 19X172 Hastelloy- 19X012 19X044 19X028 19X060 19X092 19X076 19X108 19X140 N 19X158 19X190 19X174 Nitrile 316 SST 19X016 19X048 19X032 19X064 19X096 19X080 19X112 19X144 N 19X160 19X192 19X SST 19X013 19X045 19X029 19X061 19X093 19X077 19X109 19X141 N 19X155 19X187 19X171 EPDM PVDF 19X014 19X046 19X030 19X062 19X094 19X078 19X110 19X142 N 19X157 19X189 19X173 Hastelloy- 19X015 19X047 19X031 19X063 19X095 19X079 19X111 19X143 N 19X159 19X191 19X175 Hose Pumps with No Motor Drive and IE onnection hoose Your Hose & Hose arb Materials Hose arb Hose Material Material SoloTech 10 SoloTech 23 SoloTech 26 SoloTech 30 Low Mid High Low Mid High Low Mid High Low Mid High Natural Rubber 316 SST 19X001 19X033 19X017 19X049 19X081 19X065 19X097 19X129 19X113 19X145 19X177 16X SST 19X002 19X034 19X018 19X050 19X082 19X066 19X098 19X130 19X114 19X146 19X178 19X162 SM PVDF 19X003 19X035 19X019 19X051 19X085 19X067 19X099 19X133 19X115 19X149 19X181 16X165 Hastelloy- 19X004 19X036 19X020 19X055 19X086 19X071 19X103 19X134 19X119 19X151 19X183 16X167 Nitrile 316 SST 19X005 19X037 19X021 19X054 19X084 19X070 19X102 19X132 19X118 19X148 19X180 16X SST 19X006 19X038 19X022 19X052 19X083 19X068 19X100 19X141 19X116 19X147 19X179 16X163 EPDM PVDF 19X007 19X039 19X023 19X053 19X087 19X069 19X101 19X135 19X117 19X150 19X182 16X166 Hastelloy- 19X008 19X040 19X024 19X056 19X088 19X072 19X104 19X136 19X120 19X152 19X184 19X

104 SoloTech Hose Pumps Hose Pumps with No Motor Drive or Gearbox hoose Your Hose & Hose arb Materials Hose Material Hose arb Material SoloTech 10 SoloTech 23 SoloTech 26 SoloTech 30 Natural Rubber 316 SST 19Y008 19Y017 19Y026 19Y035 PVDF 19Y007 19Y016 19Y025 19Y SST 19Y003 19Y012 19Y021 19Y030 SM PVDF 19Y002 19Y011 19Y020 19Y029 Hastelloy- 19Y001 19Y010 19Y019 19Y028 Nitrile 316 SST 19Y000 19Y009 19Y018 19Y SST 19Y006 19Y015 19Y024 19Y033 EPDM PVDF 19Y005 19Y014 19Y023 19Y032 Hastelloy- 19Y004 19Y013 19Y022 19Y031 ccessories Replacement Hose Kits Includes 2 lamps Hose arb Material SoloTech 10 SoloTech 23 SoloTech 26 SoloTech 30 Natural Rubber 24Y797 24Y801 24Y805 24Y809 SM 24Y798 24Y802 24Y806 24Y810 EPDM 24Y799 24Y803 24Y807 24Y811 Nitrile 24Y800 24Y804 24Y808 24Y812 VFDs (Variable Frequency Drives) Hp Input Voltage Output Voltage Part Number or 240 V (1 Phase) 240 V (3 Phase) 16K V (1 or 3 Phase) V (3 Phase) 16K or 240 V (1 Phase) 240 V (3 Phase) 16K V (1 or 3 Phase) V (3 Phase) 16K or 240 V (1 Phase) 240 V (3 Phase) 16K V (1 or 3 Phase) V (3 Phase) 16K V (1 or 3 Phase) V (3 Phase) 16K V (3 Phase) V (3 Phase) 16K V (1 or 3 Phase) V (3 Phase) 17K V (3 Phase) V (3 Phase) 17K697 Leak Detector Kits Description Part Number SoloTech Leak Detector Kit 24Y849 Leak Sensor onnection able for Pumps (9.8ft / 3meter) 17H389 Leak Sensor onnection able for Pumps (24.6ft / 7.5meter) 17H390 Leak Sensor onnection able for Pumps (52.5ft / 16meter) 17H391 Leak Sensor onnection able for LD Pumps (9.8ft / 3meter) Leak Sensor onnection able for LD Pumps (24.6ft / 7.5meter) 17H349 Leak Sensor onnection able for LD Pumps (52.5ft / 16meter) 17H352 Hose Pump Lubricant Description Glycerin ased Hose Lube (1 quart) Glycerin ased Hose Lube (1/2 gallon) Glycerin ased Hose Lube (1 gallon) Glycerin ased Hose Lube (55 gallon drum) Silicone ased Hose Lube (1 gallon) Silicone ased Hose Lube (55 gallon drum) Part Number 24K692 24Y920 24K694 24M435 24K686 24M

105 SoloTech Hose Pumps Technical Specifications Model SoloTech 10 SoloTech 23 SoloTech 26 SoloTech 30 Hose Size 10 mm 23 mm 26 mm 30 mm Max flow - gpm (lpm).685 (2.60) 4.75 (17.98) (38.54) 16.0 (60.57) Flow - gallon/rev (liter/rev) (0.0265) (0.190) (.412) (0.662) Pump Speed Range Low Mid High Low Mid High Low Mid High Low Mid High Gearbox Ratio 157:1 48:1 19.5:1 157:1 48: :1 145:1 47: :1 150:1 48:1 19.7:1 Motor Pumps LD Motor Pumps Horsepower Pump 60 Hz - rpm Flow 60 Hz - gpm (lpm) Minimum Flow Rate - gpm (lpm) (0.32) 0.01 (.038) 0.27 (1.02) 0.05 (.189).685 (2.60) 0.1 (.379) 0.57 (2.16) 0.1 (.379) 1.89 (7.15) 4.75 (17.98) 1.35 (5.11) 4.18 (15.82) (38.54) 2.1 (7.95) 6.55 (24.80) Gearbox Ratio 37.66: : : :1 Max. Pump Speed Range (RPM) Horsepower Flow Rate Range - gpm (lpm) ( ) ( ) ( ) ( ) 0.3 (1.14) 0.8 (3.03) 0.2 (.757) 0.7 (2.65) 1.7 (6.44) 0.4 (1.51) 1.1 (4.16) 16.0 (60.57) 2.7 (10.22) Maximum Working Pressure 125 psi (8.6 bar) 125 psi (8.6 bar) 125 psi (8.6 bar) 125 psi (8.6 bar) Maximum Suction Lift - ft (m) 29 (8.9) 29 (8.9) 29 (8.9) 29 (8.9) Pump Inlet / Outlet Size DIN PN /8 in, NSI 150 1/2 NPS, JIS 10K 10 DIN PN in, NSI /4 NPS, JIS 10K 025 DIN PN in, NSI /4 NPS, JIS 10K 025 DIN PN /4 in, NSI /2 NPS, JIS 10K 032 Operation Manual Repair Parts Manual

106 SoloTech Hose Pumps Performance harts NOTE: s back pressure increases, flow rate may decrease, especially for low-viscosity fluids at low cycle rates. Data were obtained using water as a medium with no back pressure. L Motor (low speed) M Motor (medium speed) H Motor (high speed) D MPM rushless D motor Shading indicates the recommended continuous duty range. SoloTech 10 SoloTech 26 Pump Flow Rate gpm (lpm) 0.7 (2.65) 0.6 (2.27) 0.5 (1.89) 0.4 (1.51) 0.3 (1.14) 0.2 (0.76) 0.1 (0.38) 0.0 D Pump Speed, ycles per Minute Pump Flow Rate gpm (lpm) 11 (41.6) 10 (37.9) 9 (34.1) 8 (30.3) 7 (26.5) 6 (22.7) 5 (18.9) 4 (15.1) 3 (11.4) 2 (7.6) 1 (3.8) 0.0 D Pump Speed, ycles per Minute SoloTech 23 SoloTech 30 Pump Flow Rate gpm (lpm) 5.0 (18.9) 4.5 (17.0) 4.0 (15.1) 3.5 (13.3) 3.0 (11.4) 2.5 (9.5) 2.0 (7.6) 1.5 (5.7) 1.0 (3.8) 0.5 (1.9) 0.0 D Pump Speed, ycles per Minute Pump Flow Rate gpm (lpm) (60.6) 16 (56.8) 15 (53.0) 14 (49.2) 13 (45.4) 12 (41.6) 1 1 (37.9) 10 D (34.1) 9 (30.3) 8 (26.5) 7 (22.7) 6 (18.9) 5 (15.1) 4 (11.4) 3 (7.6) 2 (3.8) Pump Speed, ycles per Minute 104

107 SoloTech Hose Pumps Dimensions SoloTech 10 and SoloTech 23 Pumps E D D E Ref. in cm in cm in cm in cm in cm ST10 H ST10 M ST10 L ST23 H ST23 M ST23 L SoloTech 26 and SoloTech 30 Pumps E E F F D D Ref. Ref. ST26 H ST26 M H ST26 M L ST30 ST26 H L ST30 H M ST30 L M ST30 L D E in cm in cm in cm in D cm in E cm 21.7 in 55.1 cm 16.5 in 41.9 cm 34.0 in 86.4 cm 14.0 in 35.6 cm 2.0 in cm Refer to manual for additional dimensions 105

108 SoloTech Hose Pumps Dimensions SoloTech 10, SoloTech 23 and SoloTech 26 LD Pumps D E Ref. ST10 MPM ST23 MPM ST26 MPM D E in cm in cm in cm in cm in cm SoloTech 30 LD Pumps E E F F D D Ref. Ref. ST26 H ST26 M H ST26 M L ST30 ST26 H L ST30 H M ST30 L M ST30 L D E in cm in cm in cm in D cm in E cm 21.7 in 55.1 cm 16.5 in 41.9 cm 34.0 in 86.4 cm 14.0 in 35.6 cm 2.0 in cm Refer to manual for additional dimensions 106

109 Hydra-lean ir-operated Pressure Washers Ordering Information Pneumatic Hydra-lean Package Order Number or or or W473 with Hose Reel or Package Instruction Manual ir Motor Part Number N34DN0 N65DN0 N65DN0 N65DN0 N65DN ir Motor Manual Pump Lower Part number Pump Manual Wetted Parts SST/PTFE/ F-PTFE SST/F-PTFE/ UHMWPE SST/F-PTFE/ UHMWPE SST/F-PTFE/ UHMWPE SST/F-PTFE/ UHMWPE SST/R/ UHMWPE Pump Std. Repair Kit See Maual See Maual Optional PTFE Repair Kit N/ Std. Discharge hose (3/8 x 50 ft) 4500 psi with M & F QD's Std. Gun/Wand ssy / Std. 60 Mesh Inlet Strainer 15T284 15T284 15T284 15T284 15T Hydraulic Hydra-lean Package Order Number 24V616 24V628 24W474 with Hose Reel 24V617 24V629 Package Instruction Manual Hydraulic Motor Part Number 24W139 24W139 24W139 24W139 24W139 Hydraulic Motor Manual Pump Lower Part number Pump Manual Wetted Parts SST/PTFE/ F-PTFE SST/F-PTFE/ UHMWPE SST/F-PTFE/ UHMWPE SST/F-PTFE/ UHMWPE SST/F-PTFE/ UHMWPE Pump Std. Repair Kit Optional PTFE Repair Kit Std. Gun/Wand ssy Std. 60 Mesh Inlet Strainer 15T284 15T284 15T284 15T284 15T284 Hydra-lean Hydraulic art-mount* (Wall mount unit also available) Hydra-lean ir-operated Wall-Mount Hydra-lean ir-operated art-mount Hydra-lean ir-operated 10:1 Drum-Mount *Hose Reel is only included with cart mount package 24W

110 Hydra-lean Pressure Washers Technical Specifications Pneumatic Hydra-lean Part Number Pump Package :1 art Mount :1 Wall Mount :1 art Mount :1 Wall Mount :1 art Mount Max. Working Pressure 1250 psi (86 bar, 8.6 MPa) 1250 psi (86 bar, 8.6 MPa) 2275 psi (157 bar, 15.7 MPa) 2275 psi (157 bar, 15.7 MPa) 3065 psi (211 bar, 21.1 MPa) 24W473** 30:1 art Mount 3065 psi (211 bar, 21.1 MPa) :1 Wall Mount 3065 psi (211 bar, 21.1 MPa) :1 art Mount 4000 psi (276 bar, 27.6 MPa) :1 Wall Mount 4000 psi (276 bar, 27.6 MPa) :1 Drum Mount 1800 psi (125 bar, 12.5 MPa) Max. ir Input Pressure 100 psi (7 bar, 0.7 MPa) 100 psi (7 bar, 0.7 MPa) 100 psi (7 bar, 0.7 MPa) 100 psi (7 bar, 0.7 MPa) 100 psi (7 bar, 0.7 MPa) 100 psi (7 bar, 0.7 MPa) 100 psi (7 bar, 0.7 MPa) 100 psi (7 bar, 0.7 MPa) 100 psi (7 bar, 0.7 MPa) 180 psi (12.5 bar, 1.2 MPa) Fluid Flow at 60 cpm 8.7 gpm (33.0 lpm) 8.7 gpm (33.0 lpm) 9.2 gpm (34.7 lpm) 9.2 gpm (34.7 lpm) 6.8 gpm (25.9 lpm) 6.8 gpm (25.9 lpm) 6.8 gpm (25.9 lpm) 4.6 gpm (17.4 lpm) 4.6 gpm (17.4 lpm) 3.0 gpm (11.4 lpm) Volume per ycle ir Inlet Size Fluid Inlet Size Fluid Outlet Size 18.6 oz (550 cc) 3/4 npt(f) 1 in 3/8 in 18.6 oz (550 cc) 3/4 npt(f) 1 in 3/8 in 19.6 oz (580 cc) 3/4 npt(f) 1 in 3/8 in 19.6 oz (580 cc) 3/4 npt(f) 1 in 3/8 in 14.5 oz (430 cc) 3/4 npt(f) 1 in 3/8 in 14.5 oz (430 cc) 3/4 npt(f) 1 in 3/8 in 14.5 oz (430 cc) 3/4 npt(f) 1 in 3/8 in 9.8 oz (290 cc) 3/4 npt(f) 1 in 3/8 in 9.8 oz (290 cc) 3/4 npt(f) 1 in 3/8 in 6.4 oz (189 cc) 1/2 npt(f) 1/2 in 3/4 in Hydraulic Hydra-lean Part Number 24V616 24W474** 24V628 24V617 24V629 Pump Package 3000H art 3000H art 3000H Wall 4300H art 4300H Wall Max. Working Pressure 3,000 psi (206.7 bar) 3,000 psi (206.7 bar) 3,000 psi (206.7 bar) 4,300 psi (296.3 bar) 4,300 psi (296.3 bar) Max. Stall Pressure 3,500 psi (241 bar) 3,500 psi (241 bar) 3,500 psi (241 bar) 5,000 psi (344 bar) 5,000 psi (344 bar) Max. Hydraulic Inlet Pressure 1,900 psi (131 bar) 1,900 psi (131 bar) 1,900 psi (131 bar) 1,900 psi (131 bar) 1,900 psi (131 bar) Hydraulic Flow Required 12 gpm (45.4 lpm) 12 gpm (45.4 lpm) 12 gpm (45.4 lpm) 18 gpm (68.1 lpm) 18 gpm (68.1 lpm) Fluid Flow at 60 PM 6.8 gpm (25.9 lpm) 6.8 gpm (25.9 lpm) 6.8 gpm (25.9 lpm) 9.2 gpm (34.7 lpm) 9.2 gpm (34.7 lpm) Hydraulic Inlet Size Hydraulic Outlet Size Fluid Inlet Size Fluid Outlet Size 3/4 JI 3/4 JI 1 in 3/8 in 3/4 JI 3/4 JI 1 in 3/8 in 3/4 JI 3/4 JI 1 in 3/8 in 3/4 JI 3/4 JI 1 in 3/8 in 3/4 JI 3/4 JI 1 in 3/8 in **Hose Reel is included with cart mount package 24W474 Maximum fluid pressure when spraying with available Graco spray tips. Smaller tips or stalled conditions result in higher pressure. 108

111 Hydra-lean Pressure Washers ccessories GUNS ND WNDS 15T282 Optional replacement SST spray gun 15T in (81 cm) SST wand 15T in (25 cm) SST wand Gun SST quick disconnent connections Fluoroelastomer (FKM) o-ring kit for gun For use with aggressive cleaning chemicals SPRY TIPS D D Oscillating Spray Tip in (3.8 mm), 5,000 psi (344 bar) maximum pressure Rotating Spray Tip in (3.8 mm), 4,500 psi (310.0 bar) maximum pressure Rotating Spray Tip in (4.0 mm), 5,000 psi (344 bar) maximum pressure Diameter Orfice Spray Tip in (0.5 mm), 15º Diameter Orfice Spray Tip in (0.5 mm), 25º Diameter Orfice Spray Tip in (0.8 mm), 40º Diameter Orfice Spray Tip in (1.1 mm), 25º Diameter Orfice Spray Tip in (1.7 mm), 40º Diameter Orfice Spray Tip in (2.0 mm), 0º Diameter Orfice Spray Tip in (1.6 mm), 40º OTHER E F G H mesh inlet strainer with 1 in npt(f) connection 15T272 24W X732 24W670 Quick oupling For adding a second hose with gun to the outlet of the pump Hose Reel Kit 5,000 psi (344 bar) maximum pressure Foaming ttachment 5,000 psi (344 bar) maximum pressure Pulsation Dampener, Forged Steel 4,750 psi (327.3 bar) maximum pressure Pulsation Dampener, Stainless Steel 3,000 psi (206.7 bar) maximum pressure (not pictured) hemical Injector Kit 4,500 psi (310 bar) maximum pressure 109

112 Hydra-lean Pressure Washers Dimensions Pneumatic Hydra-lean Wall Mount Package art Mount Package in (452 mm) 44.3 in (1125 mm) 50.0 in (1270 mm) 30.8 in (782 mm) 17.1 in (434 mm) 17.1 in (434 mm) 5.6 in (142 mm) Refer to manual for additional package dimensions 25.7 in (653 mm) Hydraulic Hydra-lean Wall Mount 24W in (45.0 cm) Wall Mount 20.4 in (51.8 cm) art Mount 52.0 in (123.1 cm) 47.3 in (120.1 cm) 55.9 in (142.0 cm) 23.4 in (59.4 cm) 28.4 in (72.1 cm) 12.6 in (32.0 cm) 12.7 in (32.3 cm) 12.7 in (32.3 cm) 3.7 in (9.4 cm) Refer to manual for additional dimensions in (65.3 cm) 110

113 Ordering Information PRT NUMER ONSTRUTION PKING Drum/S/SST (ETL-UL, E) T&L Drum/S/SST (ETL-UL, E) PE Drum/SST (ETL-UL, E) PE Stubby/S/SST (ETL-UL, E) L Stubby/S/SST (ETL-UL, E) PE Stubby/SST (ETL-UL, E) PE Drum/S/SST (E) T Drum/S (E) R Stubby/S (E) R Drum/S (E) R Stubby/SST (E) R Drum/SST (E) R Drum/SST (E) T Stubby/S (E) L Stubby/S (E) T Stubby/SST (E) T Drum/S (E) L Drum/S (E) T N = Neoprene SST = 304 Stainless Steel L = Leather S = arbon Steel T = PTFE PE = Polyethylene R = Rubber Performance harts Selector Tool Technical Specifications Fast-Flo 1:1 Priming Piston Maximum fluid working pressure 180 psi (12.4 bar, 1.24 MPa) Maximum pump speed 100 cpm Pump cycles per gallon (3.8 l) 25 Maximum air input pressure 180 psi (12.4 bar, 1.24 MPa) Maximum operating temperature 120 F (49 ) Typical sound level 72 da ir inlet 1/4 npt (f) Fluid outlet 3/4 npt (f) Weight 20 lbs (9.07 kg) Drum; 11 lbs (4.99 kg) Stubby Instruction Manual Dimensions Fast-Flo 1:1 ir-operated Piston Transfer Pumps To order a FastFlo pump, use the online selector tool at or contact your distributor. FLUID OUTLET PRESSURE psi (bar, MPa) 120 (8.4, 0.84) 100 (7, 0.7) 80 (5.5, 0.55) 60 (4.1, 0.41) 40 (2.8, 0.28) 20 (1.4, 0.14) 0 gpm (lpm) 0 YLE RTE (8.4) 250 (7.0) 1 (3.8) Fast-Flo 1:1 Performance 2 (7.6) FLUID FLOW 3 (11) 4 (15.2) 200 (5.6) 150 (4.2) 100 (2.8) 50 (1.4) IR ONSUMPTION scfm (m 3 /min) 45.6 in. (1158 mm) Extends to 63.5 in. (1614 mm) 51.7 in. (1315 mm) IR PRESSURE = at 100 psi (7 bar, 0.7 MPa) = at 70 psi (4.8 bar, 0.48 MPa) = at 40 psi (2.8 bar, 0.28 MPa) LEGEND ir onsumption Fluid Pressure 36.2 in. (920 mm) 8.9 in. (228 mm) 111

114 Piston Pumps for Ink pplications Ink pplications Selector Tool To order a SoloTech pump, use the online selector tool at or contact your distributor. Ordering Information and Technical Specifications Piston Pumps with Sealed Wet up Ink Pump Package Part No. Ratio DataTrak Remote DataTrak Power Source Displacement per ycle Maximum ir or Hydraulic Input Pressure psi (MPa, bar) Maximum Fluid Working Pressure psi (MPa, bar) :1 ir 500 cc 100 (0.7, 7.0) 1400 (9.7, 97) :1 x ir 500 cc 100 (0.7, 7.0) 1400 (9.7, 97) :1 x ir 500 cc 100 (0.7, 7.0) 1400 (9.7, 97) :1 ir 200 cc 100 (0.7, 7.0) 2300 (15.9, 159) :1 x ir 200 cc 100 (0.7, 7.0) 2300 (15.9, 159) :1 x ir 200 cc 100 (0.7, 7.0) 2300 (15.9, 159) :1 ir 500 cc 100 (0.7, 7.0) 2600 (17.9, 179) :1 x ir 500 cc 100 (0.7, 7.0) 2600 (17.9, 179) :1 x ir 500 cc 100 (0.7, 7.0) 2600 (17.9, 179) :1 Hydraulic Oil 500 cc 1500 (10, 103) 2300 (15.9, 159) Motor onversion Kits Part No D625 Description To install an L200M heck-mate displacement pump on an existing King air motor To install an L500M heck-mate displacement pump on an existing King air motor To install an L500M heck-mate displacement pump on an existing Viscount II hydraulic motor Piston Pumps with Sealed Wet up Stroke length Pneumatic Hydraulic 4.75 in ( mm) 4.69 in ( mm) Maximum fluid operating temperature 180 F (82.3 ) ir or Hydraulic Inlet Size 3/4 npt (f) Fluid outlet size 200 cc displacement pump: 1 npt (f) 500 cc displacement pump: 1-1/2 npt (f) Maximum pump speed 60 cpm (Do not exceed maximum recommended speed of fluid pump, to prevent premature pump wear) Other Part No. Description Floor Stand Kit See manual Pneumatic Hydraulic 112

115 Piston Pumps for Ink pplications Ordering Information and Technical Specifications Name of Pump Senator 19:1 Viscount II 1900 ulldog 31:1 Viscount II 3100 Lower size Maximum fluid pressure 1900 psi (131 bar, 13.1 MPa) 1900 psi (131 bar, 13.1 MPa) 3100 psi (213 bar, 21.3 MPa) 3100 psi (213 bar, 21.3 MPa) Maximum motor inlet pressure 100 psi (air) (6.9 bar, 0.69 MPa) 450 psi (oil) (31 bar, 3.1 MPa) 100 psi (air) (6.9 bar, 0.69 Mpa) 750 psi (oil) (51.7 bar, 5.1 MPa) Flow 60 cpm 2.8 gpm (10.6 lpm) 2.8 gpm (10.6 lpm) 2.8 gpm (10.6 lpm) 2.8 gpm (10.6 lpm) fm or gpm required per gallon 24 cfm 4.3 gpm (16.2 lpm) 32 cfm 4.3 gpm (16.2 lpm) Fluid pump outlet size 1 npt (f) 1 npt (f) 1 npt (f) 1 npt (f) Motor inlet size 3/4 npt (f) 3/4 npt (f) 3/4 npt (f) 3/4 npt (f) Weight of pump 160 lb (73 kg) 177 lb (80 kg) 160 lb (73 kg) 177 lb (80 kg) Instruction manual in Supply Senator 19:1 Viscount II 1900 ulldog 31:1 Viscount II 3100 Pump ir controls: FRL, 1/ ir run away control, 3/ ir speed control, 1/2 (f) Floor stand (3 inlet) Hydraulic controls* Outlet hydraulic hose connector 1 (m) x 1-1/2 (f), 1500 psi rated Not included Not included Misc. Information Senator 19:1 Viscount II 1900 ulldog 31:1 Viscount II 3100 Pump lower section Ram plate replacement seals *Hydraulic controls include hydraulic flow and pressure control, ball valves, 3 ft supply and return hose 19:1 Senator 31:1 ulldog 113

116 Piston Pumps for Ink pplications Ordering Information and Technical Specifications Name of Pump ulldog 12:1 Viscount II 1200 King 24:1 Viscount II 2400 Lower size Maximum fluid pressure 1200 psi (82.8 bar, 8.28 MPa) 1200 psi (82.8 bar, 8.28 MPa) 2400 psi (165 bar, 16.5 MPa) 2400 psi (165 bar, 16.5 MPa) Maximum motor inlet pressure 100 psi (air) (6.9 bar, 0.69 MPa) 750 psi (oil) (51.7 bar, 5.1 Mpa) 100 psi (air) (6.9 bar, 0.69 Mpa) 1500 psi (oil) (103 bar, 10.3 Mpa) Flow 60 cpm 7.5 gpm (28.4 lpm) 7.5 gpm (28.4 lpm) 7.5 gpm (28.4 lpm) 7.5 gpm (28.4 lpm) fm or gpm required per gallon 20 cfm 1.6 gpm (6 lpm) 25 cfm 1.6 gpm (6 lpm) Fluid pump outlet size 1-1/2 npt (m) 1-1/2 npt (m) 1-1/2 npt (m) 1-1/2 npt (m) Motor inlet size 3/4 npt (f) 3/4 npt (f) 3/4 npt (f) 3/4 npt (f) Weight of pump 142 lb (65 kg) 196 lb (89 kg) 160 lb (73 kg) 196 lb (89 kg) Instruction manual in Supply ulldog 12:1 Viscount II 1200 King 24:1 Viscount II 2400 Pump ir controls: FRL, 1/ ir run away control, 3/ ir speed control, 1/2 (f) Floor stand (3 inlet) Hydraulic controls* Outlet hydraulic hose connector 1 (m) x 1-1/2 (f), 1500 psi rated Not included Not included Misc. Information ulldog 12:1 Viscount II 1200 King 24:1 Viscount II 2400 Pump lower section Ram plate replacement seals *Hydraulic controls include hydraulic flow and pressure control, ball valves, 3 ft supply and return hose 12:1 ulldog Viscount II :1 King 114

117 Piston Pumps for Ink pplications Ordering Information and Technical Specifications Piston Pumps President 20:1 Lower size 450 Maximum fluid pressure 2000 psi (140 bar. 14 MPa) Maximum motor inlet pressure 100 psi ( 7 bar, 0.7 MPa) Flow 60 cpm 1.2 gpm (4.5 lpm) fm or gpm required per gallon 35 cfm Fluid pump outlet size 3/4 npt (f) Motor inlet size 1/2 npt (f) Weight of pump 50 lb (22.7 kg) Instruction manual in Supply President 20:1 Pump ir controls: FRL, 3/8 (f) Floor stand (3 inlet) ir run away control, 3/4 (f) ir speed control 1/2 (f) Misc. Information President 20:1 Pump lower section Ram plate replacement seals :1 President 115